NX750P
15-inch Powered Loudspeaker Cabinet
Features:
· Integrated 1600 Watt Amplifier (Peak) (750 Watts Program)
· Bi-amplified Power Module
· Max SPL 133dB Peak (127dB Continuous)
· 15-inch High Efficiency Woofer
· 1.5-inch Polyester Horn Driver (1-inch Exit)
· Designed as Front-of-house or Monitor Loudspeaker
· 80° x 50° Custom Waveguide Horn
· Rugged Lightweight Molded Composite Cabinet Construction
· XLR ,1/4-inch Microphone& Line Inputs
· All-Metal Grille, Integrated Flypoints, Handles & Stand Mount
· 126 dB Maximum SPL
Overview:
The NX750P is the culmination of all of Yorkville’s research and development of molded technology to this point in time. The injection molded
loudspeaker enclosure is loaded with a high performance 15-inch woofer and an 80º x 50º rotatable custom Waveguide horn.
It delivers 1600 Watts (Peak) and uses the same combination of amplifier technologies that have already been proven in Yorkville active loudspeakers.
The horn amplifier uses a two-tier class H linear technology, allowing the horn to produce loud clean transients to keep up with the high output of the
woofer. The two-tier amplifier technology is a lower weight, more efficient amplifier with higher headroom and lower operating temperature. It is a
perfect solution for powering the top end.
Like the NX55P, careful consideration was taken in the design process to ensure the NX750P can easily
be used in any orientation, close to walls, floors, and in close arrays with multiple cabinets. Particular care
was taken designing the components to reduce extraneous heat production.
NX750P Specifications:
NX750P
Model
Active 2-Way Bi-Amplified
Integrated 1600 Watt Amplifier (Peak)
(750 Watts Program)
50 - 26000
SYSTEM TYPE
The NX750P has a versatile direct input system and built-in mixer. The mixer allows the loudspeaker to
be used directly with a microphone and / or line source. The loop output allows additional active cabinets
to be driven from one cabinet’s mixer stage, or a series of cabinets to be driven from one source. If desired,
multiple NX750P’s can be combined using the mixer inputs on each cabinet and coupling the loop outputs.
This way you would have the ideal presentation system with two microphone inputs and two line inputs
without any additional mixer.
PROGRAM POWER (watts)
FREQ. RESPONSE (Hz +/- 3dB)
MAXIMUM SPL (dB)
X-OVER FREQUENCY (Hz)
LF DRIVER(S)
133dB Peak (127dB Continuous)
1300
15" High Efficiency Woofer
Injected Molded Waveguide
1.5" Polyester
HF HORN
HF DRIVER
The microphone input has equalization and high pass filtering appropriate for vocal applications. The trim
control allows looped cabinets to be individually adjusted in level. The NX750P has user defeatable 100Hz
high pass filters to allow the cabinet to be used more efficiently with any Yorkville active subwoofer.
1"
HF HORN THROAT DIAMETER
HF DISPERSION (H° x V°)
HF PROTECTION
LF PROTECTION
80 x 50 Rotatable
Thermal/Peak Limiter
Thermal/Overcurrent
Injection Molded
CONSTRUCTION
GRILLE
Perforated Metal
XLR-F (mic) / 1/4" TRS x 2
Mic/Line Gain / 2-Band EQ
+/- 6 dB Input Trim Control
Subwoofer Tuning / Selection Switch
XLR-M / XLR-F 1/4" TRS x 2
1 x Side Bar
INPUTS
Optional NX Flying Hardware
MIXER / CONTROLS
The NXF flyware is a unique and versatile U-bracket system that attaches to the integrated flypoints
on NX cabinets for a safe and secure installation. Once mounted, the cabinets can be flown at almost
any angle with a standard shackle and cable system. In addition, the cabinet can be angled up to
30 degrees left or right across the horizontal plane within the NXF U-bracket. Flying an array of NX
cabinets with ideal spacing between boxes is possible by joining multiple NXF U-Brackets and their
mounted cabinets together with a simple arraying adaptor.
LOOP IN / OUTPUTS
HANDLES
1/4-20 x 5
FLYWARE TYPE / QUANTITY
FLYWARE LOCATIONS
2 Top / 2 Back / 1 Bottom
NXF Brackets
OPTIONAL ACCESSORIES
STAND MOUNT ADAPTOR
DIMENSIONS (DxWxHxBW inches)
DIMENSIONS (DxWxHxBW cm)
WEIGHT (lbs / kg)
Yes
32 x 22 x 15 x 9.5
84 x 56 x 38 x 24
62 / 28
NXF6000 - Steel U-Bracket flying assembly
NXF600W - Wall Mounting Bracket (to attach NXF35U assembly to wall or pillar)
NXF600A - Array Link Assembly (to properly array NXF600U flying assemblies - sold in pairs)
y o r k v i l l e . c o m
|