NX55P
12-inch Powered Loudspeaker Cabinet
Features:
· Integrated 1200 Watt Amplifier (Peak) (550 Watts Program)
· Bi-amplified Power Module
· Max SPL 131dB Peak (125dB Continuous)
· 1.4-inch Aluminum Diaphragm Horn Driver (1-inch Exit)
· Designed as Front-of-house or Monitor Loudspeaker
· 80° x 50° Custom Waveguide Horn
· Rugged Lightweight Molded Composite Cabinet Construction
· XLR ,1/4-inch Microphone& Line Inputs
· All-Metal Grille, Integrated Flypoints, Handles & Stand Mount
· 125 dB Maximum SPL
Overview:
The NX55P active speaker enclosure uses a combination of amplifier technologies to create the best
combination of lightweight enclosure and high quality sound.
The 1200-watt (Peak) bi-amplified NX55P uses a two-tier class H linear technology for high frequencies, allowing the horn to produce loud clean transients to
keep up with the high output of the woofer. The two-tier amplifier technology is a lower weight, more efficient amplifier with higher headroom and lower
operating temperature, and a perfect solution for powering the top end. The woofer or low frequency amplifier uses Class D switching technology to reduce
overall weight of the amplifier section, and deliver maximum power to the 12-inch woofer.
The NX55P can easily be used in any orientation, and close to walls, floors and in close arrays with multiple cabinets. Particular care was taken designing
the components to reduce extraneous heat production.
The NX55P has a versatile direct input system and built-in mixer. The mixer allows the loudspeaker to be used
directly with a microphone and / or line source. The loop output allows additional active cabinets to be driven
from one cabinet’s mixer stage, or a series of cabinets to be driven from one source. The NX55P has user
defeatable 100Hz high pass filters that allow either cabinet to be used more efficiently with any Yorkville active
subwoofer.
NX55P Specifications:
NX55P
Model
Active 2-Way Bi-Amplified
1200 Watt Amplifier (Peak)
(550 Watts Program)
45 - 18000
SYSTEM TYPE
PROGRAM POWER (watts)
FREQ. RESPONSE (Hz +/- 3dB)
MAXIMUM SPL (dB)
X-OVER FREQUENCY (Hz)
LF DRIVER(S)
Integrated bar handles, 1/4-20 flypoints and integrated stand mount adaptor, as well as 1/4-inch TRS and XLR
inputs ensure the NX55P can be easily integrated into any live or DJ PA set up.
131dB Peak (125dB Continuous)
2000
12" Woofer
Molded Composite
1" Aluminum
HF HORN
HF DRIVER
1.4"
HF HORN THROAT DIAMETER
HF DISPERSION (H° x V°)
HF PROTECTION
LF PROTECTION
Optional NX Flying Hardware
80 X 50
Thermal / Peak Limiter
Thermal / Overcurrent
Molded Composite
Perforated Metal
The NXF flyware is a unique and versatile U-bracket system that attaches to the integrated flypoints on NX cabinets
for a safe and secure installation. Once mounted, the cabinets can be flown at almost any angle with a standard
shackle and cable system. In addition, the cabinet can be angled up to 30 degrees left or right across the
horizontal plane within the NXF U-bracket. Flying an array of NX cabinets with ideal spacing between boxes is
possible by joining multiple NXF U-Brackets and their mounted cabinets together with a simple arraying adaptor.
CONSTRUCTION
GRILLE
XLR-F (mic) 1/4" TRS balanced (x2)
Mic/Line Gain / 2-Band EQ
+/- 6 dB Input Trim Control
Subwoofer Tuning / Selection Switch
XLR-M / XLR-F 1/4" TRS balanced (x2)
1 x Side Bar
INPUTS
MIXER / CONTROLS
NXF35U - Steel U-Bracket flying assembly
NXF35W - Wall Mounting Bracket (to attach NXF35U assembly to wall or pillar)
NXF35A - Array Link Assembly (to properly array NXF350U flying assemblies - sold in pairs)
LOOP IN / OUTPUTS
HANDLES
1/4-20 x 5
FLYWARE TYPE / QUANTITY
FLYWARE LOCATIONS
2 Top / 1 Bottom
NXF Brackets
OPTIONAL ACCESSORIES
STAND MOUNT ADAPTOR
DIMENSIONS (DxWxHxBW inches)
DIMENSIONS (DxWxHxBW cm)
WEIGHT (lbs / kg)
Yes
12.25 x 16 x 26.5 x 9
31.1 x 40.6 x 67.3 x 22.9
41 / 18.6
y o r k v i l l e . c o m
|