|
VICTOR
1260-3
12 DIGIT HEAVY DUTY PRINTING CALCULATOR
INSTRUCTION MANUAL
OPERATIONS AND MAINTENANCE
Before Turning On - Please remove ribbon-cushion placed on a ribbon and check the rating
label on the bottom to see if the rated voltage corresponds to the local voltage before plug in
AC cord.
Note: Ribbon cushion is located under
printer cover.
CAUTIONS
1. Do not place the machine in hot, dusty or damp locations.
2. To clean the housing use a silicon-treated cloth. Do not use water or detergents.
3. Do not place anything on the housing, particularly on the head of the printer
mechanism.
4. Turn off the power switch before removing the plug from AC wall outlet.
5. Turn the power switch off while not in use.
6. The socket-outlet shall be installed near the equipment and shall be easily accessible.
ACTIVATE BACKUP BATTERY
Before start using the calculator, please remove the insulation paper below the backup
battery.
1. Turn the AC power switch OFF and remove the battery compartment cover located on
the bottom case.
2. Remove the insulation paper located below the backup battery.
3. PRESS THE RESET SWITCH.
4. Replace the battery compartment cover.
5. Turn ON the AC power switch.
6. Program the date and time according to the instruction manual.
Backup Battery
CR2025
3
Reset Button
1
2
Insulation
Paper
REMOVE BEFORE USING THE MACHINE
Depress Reset in Battery Compartment
Program Date & Time – See Operator Manual
2
REPLACING INK RIBBON
Your calculator is shipped with a 2-color ribbon already in place. You do not need to install or
change it before you begin using the calculator. When you have been using your calculator
for some time, however, the print will gradually become faint, indicating that you should
change the ribbon. To change the ribbon, follow these steps.
1. Remove paper roll, tearing paper at rear of calculator. Use the Paper Advance (↑) key to
feed the remaining paper tape through the printer. Then remove the printer cover.
2. Remove the old ribbon by pulling upward.
3. Install the ribbon spool with the black edge up. Roll from the outside of the full spool and
place the first spool on the spindle not engaged by the lever. Thread the new ribbon
along the outside of the guides and in front of the print wheels. Switch the lever to the
other side and replace the second spool.
4. Rotate the spools to take up any slack. Replace the printer cover and the paper tape.
Correct direction
Incorrect direction
HOW TO FEED THE PAPER TAPE
1. Put the new paper roll on the paper arm.
2. Insert the paper into the slot as indicated.
3. Depress the paper feed key.
4. Suitable paper roll:
Width: max. 57.5mm (2.25”)
Diameter: max. 50mm (1.97”)
Paper: Normal paper
(45kg/1000 sheets/788 x 1091 mm)
3
BATTERY REPLACEMENT
1. Turn the AC power switch off
2. Remove - the battery compartment cover located on the calculator bottom case.
3. Remove the old battery and install a new CR2025 or equivalent.
4. Turn on the AC power switch
5. PRESS THE RESET BUTTON
6. Replace the battery compartment cover.
7. Reprogram the date and time.
(See page 27 & 28)
Bottom Case
Battery
Holder
1.
Battery Cover
5.
Reset Switch
3.
Battery
CAUTION
Danger of explosion if battery is incorrectly replaced. Only
replace with the same or equivalent type recommended by
the manufacturer.
Dispose of used batteries according to the manufacturers’
instructions.
4
KEYBOARD LAYOUT
1. Decimal Selector
2. Rounding Selector
3. Sigma Switch
4. Grand Total Switch
5. Print Switch
6. Paper Feed
7. Back Space
8. Cost
17. Equal
18. Multiplication
19. Sign Change
20. Delta Percentage
21. Clear Entry / Clear
22. Numeric Key Pad
23. Subtraction
24. Addition
9. Sell
25. Item Count
10. Margin
26. Non-add / Subtotal
27. Total
28. Memory Total
29. Memory Subtotal
30. Memory Subtraction
31. Memory Addition
11. Time/Date Display
12. Tax Rate Preset
13. Tax 1
14. Tax 2
15. Percentage
16. Division
5
This section describes the mode switches, data entry keys, and operating keys provided
on your calculator. The following terms are used in discussing your calculator’s operation:
• The accumulator is the area of the calculator’s logic that stores a running total of
the results of addition and subtraction operations. It is the “adding machine” portion
of the calculator.
• The calculating register is the area of the calculator’s logic where the intermediate
and final results of multiplication, division and percentage calculations are stored.
The contents of the calculating register do not affect the accumulator.
• The keyboard register is the area of the calculators logic that stores the value that
will immediately be used in the next calculation.
• The item count register is the area of the calculator’s logic that counts your entries
into the accumulator. Each positive entry is counted as one item. Each Negative
entry is subtracted resulting in a net item count. It is also net or gross
programmable.
• The memory register is the area of the calculator’s logic that accumulates
amounts you add to or subtract from the memory. Because the memory register is
independent of the accumulator and the calculating register, it retains its value until
you clear it with the Memory Total (MT) key.
6
SLIDE SWITCH FEATURES
This section illustrates and describes the mode switches you can use to control your
calculator’s operation.
1. A F 0 2 3 4 Decimal Point Selector
A
Monetary Add Mode: At this setting, amounts entered are assumed to
be monetary. The calculator automatically supplies a decimal point to
the left of the last two digits entered. Use this setting to add, subtract,
multiply and divide decimals.
Units/price mode operation:
Multiplication: The first factor will be entered as a whole number and the
second factor will have a decimal point supplied to the left of the last two
digits.
Division: The first factor will have a decimal point supplied to the left of
the last two digits and the second factor will be entered as a whole
number.
F
Floating decimal point mode; this setting specifies that all digits of the
result be shown up to a maximum of 12 digits. If the result exceeds
these capacities, excess digits to the right of the decimal point are
dropped. No rounding takes place.
0,2,3,4
Fixed decimal point mode; these settings specify the number of digits to
the right of the decimal point that are shown in the result.
2. ↓ 5/4 ↑
Rounding Switch
↓
Absolute round down (truncation).
5/4
This setting causes automatic round off. If the last digit of the result that
will be printed or printed/displayed upon rounding is followed by a value
of 0 to 4, the digit is unchanged. If the last digit of the result that will be
printed or printed/displayed upon rounding is followed by a value of 5 to
9, the digit is rounded up.
↑
Absolute round up.
3. ∑ Switch
•
Calculation without sigma.
∑
Calculation with Sigma. The results of multiplication or division
calculations completed by the = or % keys are automatically added to
the accumulator. The sum of these accumulations is displayed by
pressing #/S key and displayed and cleared by pressing the T key.
7
4. Grand Total Switch
•
Calculation without Grand Total.
GT
Any total taken with T key is automatically accumulated to memory. The
accumulated grand total can be recalled by pressing the MT key.
5. OFF ON PRINT
Printer Selects Switch
OFF
Turn Off the calculator.
ON
Printer is activated only when feed key or #/S key is pressed.
PRINT
Printer is activated as long as calculator is turned on.
KEY FEATURES
6. [↑] Paper Feed key
Advance the paper roll.
7. [→] Right Shift key
Deletes right most character of a live entry.
8. [COST] Cost key
Used to enter the Cost factor in a Gross Profit Margin calculation.
9. [SELL] Sell key
Used to enter the Selling price in Gross Profit Margin calculation.
10. [MARGIN] Profit Margin key
Used to enter the desired Margin in a Gross Profit Margin calculation.
11. [TIME/DATE] Time and Date Display key
Used to display or program the date and time. Depressing this key once will
cause the date to display, a second depression will display the time. Holding the
key down for three seconds will cause the date or time to flash, this is the
program mode.
12. [RATE] TAX Rate Preset key
Used to enter TAX rate.
13. [TAX 1] Tax 1 key
Calculate an amount of Tax 1 with tax rate preset by RATE key. Use + key for
calculating an amount include VAT, and – key for calculating an amount
excluding VAT.
14. [TAX 2] Tax 2 key
Calculate an amount of Tax 2 with tax rate preset by RATE key. Use + key for
calculating an amount include VAT, and – key for calculating an amount
excluding VAT.
8
15. [%+] Percent key
Completes percent calculation when X or ÷ key is used.
16. [÷] Division key
The Division key performs division, automatic constant division and
intermediate sequential operations. It establishes the next amount as a constant
divisor. The ÷ key also causes the calculator to divide when you depress the
=, %, M+, M-, X or ÷ key. Each divisor entry is retained as a constant (except M+
and M- entries) until you depress the X, ÷ or CE/C key.
17. [=] Equal key
To get the result in multiplication or division.
18. [X] Multiplication key
The multiplication key performs multiplication, automatic constant multiplication
and intermediate sequential operations. It establishes the amount entered or the
previous printed or printed/displayed amount as a constant multiplicand. The X
key also causes the calculator to multiply when you depress the =, %, M+, M-, X
or ÷ key. Each multiplicand entry is retained as a constant (except M+ and M-
entries) until you depress the X, ÷, or CE/C key.
19. [+/-] Sign Change key
Reverse the sign on the display.
20. [Δ%] Delta Percentage
Automatically compares any two amounts and then calculates and prints the
difference and percent of change.
21. [CE/C] Clear Entry / Clear key
Clears a live entry by pressing this key once. Press twice to clear the
accumulator or pending calculation. Does not clear the Memory or Grand total.
22. [0]-[9], [00] & [•] Numeric keys.
The calculator uses the conventional 10-key indexing keyboard, and include the
double zero key and decimal point key. Whole numbers are entered exactly as
they are written.
23. [–] Minus key
Subtracts an amount from the accumulator. To subtract the same amount more
than one time (repeat subtraction), enter that amount once and depress the –
key as many times as necessary. If this key is depressed immediately after %
key, it works as percent minus key.
24. [+] Plus key
Adds an amount to the accumulator. To add the same amount more than one
time (repeat addition), enter that amount once and depress the + key as many
times as necessary. If this key is depressed immediately after % key, it works as
percent plus key.
9
25. [N] Item Count Key
Calculations with item count and/or averaging. Also used to set the N count to
Gross or Net.
26. [# / S] Date / Subtotal Key
# : It will print live entry as an identifier as an invoice number with “#” mark.
S : It prints but does not clear the accumulator.
27. [T] Total Key
Prints and clears the accumulator. When this key is pressed with the “GT” switch
is on, the result is accumulated automatically in the memory register.
28. [MT] Memory Total key
Prints and clears the memory.
29. [MS] Memory Subtotal key
Prints but do not clear the memory.
30. [M-] Memory Minus key
Subtracts an amount from memory. If there is a live calculation pending, the
Memory Minus key will complete the calculation and subtract the amount from
Memory.
31. [M+] Memory Plus key
Adds an amount to memory. If there is a live calculation pending, the Memory
plus key will complete the calculation and accumulate the result to Memory.
32. [÷], [=] Square Root key
By pressing the ÷ and then the = key, the square root result will be achieved.
TROUBLESHOOTING
Many problems such as no power, no key response etc. Can be resolved using the
RESET button. Please follow these instructions:
1. Machine must be plugged in and ON, and in the PRINT mode.
2. Turn machine over so you can see the battery compartment.
3. Open the battery compartment and locate the RESET button located next to the
silver battery.
4. Depress the RESET button; you will hear the machine cycle. If you do not hear the
machine recycle, push the button a 2nd time.
5. Replace the battery compartment cover and turn the machine right side up.
6. Test the machine.
If this procedure has not successfully resolved your problem please call 1-800-628-2420
for future assistance.
10
APPLICATION EXAMPLES
1. BACKSPACE
Decimal
Rounding
Σ
GT
Print
4
5/4
.
.
PRINT
Calculation
Enter
5.4321 [+]
2.3457 [→]
Display
5.4321
2.345
Paper
5.4321 + 2.34567 = ?
5.4321 +
67
[+]
[T]
7.77777
7.7778
2.34567 +
7.7778 T
2. ROUNDING FOR ADDITION / SUBTRACTION
Decimal
Rounding
Σ
GT
Print
0
↓
.
.
PRINT
Calculation
Enter
3.4
2.1
Display
3.4
Paper
3.4 + 2.1 = ?
[+]
[+]
[T]
3.4 +
2.1 +
5. T
5.5
5.
Decimal
Rounding
Σ
GT
Print
0
5/4
.
.
PRINT
Calculation
Enter
3.4
2.1
Display
3.4
Paper
3.4 + 2.1 = ?
[+]
[+]
[T]
3.4 +
2.1 +
6. T
5.5
6.
3. ADDITION & SUBTRACTION
Decimal
Rounding
Σ
GT
Print
F
5/4
.
.
PRINT
Calculation
Enter
Display
2.
Paper
2 + 3.1415926 - 6 = ?
2
[+]
[+]
[−]
[T]
2. +
3.1415926
6
5.1415926
- 0.8584074
- 0.8584074
3.1415926 +
6.
0.8584074 -T
−
11
4. ADDITION / SUBTRACTION IN ADD MODE
Decimal
Rounding
Σ
GT
Print
A
5/4
.
.
PRINT
Calculation
Enter
123
Display
1.23
Paper
1.23 − 4.56 + 7.89 = ?
[+]
1.23 +
456
[−]
[#/S]
[+]
- 3.33
- 3.33
4.56
4.56
−
3.33 -S
7.89 +
4.56 T
789
[T]
4.56
5. ITEM COUNT PRESETTING
Decimal
Rounding
Σ
GT
Print
A
5/4
.
.
PRINT
The Item count is Programmable for Gross Count or Net Count.
Gross Item Count: All entries both positive (+) and Negative (-) increment the counter
positively.
Example: 10 + 2 + 3 – 5 = 10
Item count is 4
Net Item Count: Plus entries increment the counter, minus entries decrement the
counter.
Example: 10 + 2 + 3 – 5 = 10
Item count is 2
Calculation
Enter
[CE/C]
Display
Paper
0.
0. C
0
Setting Item
(Press & Hold 3 sec)[N]
[+]
(Blinking) 000.
0000.
000
Cross Item Count
[CE/C]
(Press & Hold 3 sec)[N]
[-]
0.
0. C
0
Setting Item
(Blinking) 000.
000
Net Item Count
0000.
12
6. (A) ADDITION / SUBTRACTION WITH ITEM COUNT IN GROSS SETTING
Decimal
Rounding
Σ
GT
Print
A
5/4
.
.
PRINT
Calculation
Enter
1132
Display
11.32
Paper
11.32 + 7.98 − 33.33 = ?
[+]
11.32 +
7.98 +
798
[+]
19.30
[N]
[#/S]
[−]
[N]
[T]
0002.
002
003
19.30
19.30 S
33.33 –
3333
- 14.03
0003.
- 14.03
14.03 -T
0. C
[CE/C]
0.
6. (B) ADDITION / SUBTRACTION WITH ITEM COUNT IN NET SETTING
Decimal
Rounding
Σ
GT
Print
A
5/4
.
.
PRINT
Calculation
Enter
1132
Display
11.32
Paper
11.32 + 7.98 − 33.33 = ?
[+]
11.32 +
7.98 +
798
[+]
19.30
[N]
[#/S]
[−]
[N]
[T]
0002.
002
001
19.30
19.30 S
33.33 –
3333
- 14.03
0001.
- 14.03
14.03 -T
0. C
[CE/C]
0.
13
6. (C) ITEM COUNT WITH AVERAGING
Decimal
Rounding
Σ
GT
Print
A
5/4
.
.
PRINT
Calculation
Enter
123
456
789
987
Display
1.23
Paper
11.32 + 7.98 − 33.33 = ?
[+]
[+]
[+]
[+]
[T]
[N]
[N]
1.23 +
4.56 +
7.89 +
9.87 +
23.55 T
5.79
13.68
23.55
23.55
0004.
5.89
004
5.89 ∗
7. GRAND TOTAL MEMORY
Decimal
Rounding
Σ
GT
Print
A
5/4
.
GT
PRINT
Calculation
Enter
Display
0.
Paper
13.20 9.55
8.30 7.36
[CE/C]
[+]
0. C
13.2
8.3
13.20
21.50
24.45
24.45
13.20
8.30
2.95
+
+
+
+ 2.95 18.33
24.45 +35.24 =T?
[+]
2.95
[+]
24.45 MT
[T]
M
+
9.55
7.36
18.33
[+]
[+]
[+]
[T]
M
M
M
M
9.55
16.91
35.24
35.24
9.55
7.36
+
+
+
18.33
35.24 MT
+
[MT]
59.69
59.69 MT
14
8. REPETATIVE CALCULATION WITH REFERENCE TO DATE
Reference date is April 25, 2004
Decimal
Rounding
Σ
GT
Print
A
5/4
.
.
PRINT
Calculation
Enter
4.25.2004 [#/S]
Display
4.252004
6.54
Paper
# 4.25.2004
6.54 + 6.54 + 6.54 −
7.89 − 7.89 = ?
654
[+]
[+]
[+]
[−]
[−]
[T]
6.54 +
6.54 +
6.54 +
7.89 −
7.89 −
3.84 T
13.08
19.62
11.73
3.84
789
3.84
9. MULTIPLICATION
Decimal
Rounding
Σ
GT
Print
2
↓
.
.
PRINT
Calculation
Enter
Display
1.238
456.
Paper
1.238 x 456 =?
1.238
456
[x]
[=]
1.238 x
456.00 =
564.52 ∗
564.52
10. SEQUENTIAL (CHAIN) MULTIPLICATION
Decimal
Rounding
Σ
GT
Print
3
↑
.
.
PRINT
Calculation
Enter
3.21
Display
3.21
Paper
3.21 x 4.5 x 6.324 =?
[x]
[x]
[=]
3.210
4.5
3.210 x
4.500 x
4.5
14.445
6.324
91.351
6.324 =
91.351 ∗
6.324
15
11. CONSTANT MULTIPLICATION
Decimal
Rounding
Σ
GT
Print
2
5/4
.
.
PRINT
Calculation
2 x 4 = 8
Enter
Display
2.00
Paper
2
4
[x]
[=]
2.00 x
4.00 =
8.00 ∗
2 x 5 = 10
2 x 6 = 12
8.00
5
6
[=]
[=]
10.00
12.00
5.00 =
10.00 ∗
6.00 =
12.00 ∗
12. CONSTANT MULTIPLICATION WITH ACCUMULATION
Decimal
Rounding
Σ
GT
Print
2
5/4
Σ
.
PRINT
Calculation
Enter
1.79
Display
1.79
Paper
$1.79 x 167 = $298.93
1.79 x –230 = -411.70
1.79 x 140 = +186.16
= ?
[x]
[=]
1.79 x
167.00 =
298.93 +
167
298.93
230
[+/-]
[=]
- 230.
- 411.70
230.00 −=
411.70 −+
104
[=]
[T]
186.16
73.39
104.00 =
186.16 +
73.39 T
13. DIVISION
Decimal
Rounding
Σ
GT
Print
3
↓
.
.
PRINT
Calculation
Enter
178
6
Display
178.000
29.666
Paper
178 ÷ 6 = ?
[÷]
[=]
178.000 ÷
6.000 =
29.666 ∗
16
14. CONSTANT DIVISION
Decimal
Rounding
Σ
GT
Print
2
5/4
.
.
PRINT
Calculation
Enter
755
4
Display
755.00
188.75
Paper
755 ÷ 4 = 188.75
409 ÷ 4 = 102.25
32 ÷ 4 = 8.00
[÷]
[=]
755.00 ÷
4.00 =
188.75 ∗
409
32
[=]
[=]
102.25
8.00
409.00 =
102.25 ∗
32.00 =
8.00 ∗
15. DIVISION WITH ACCUMULATION
Decimal
Rounding
Σ
GT
Print
4
5/4
Σ
.
PRINT
Calculation
Enter
Display
Paper
145 ÷ 12.25 +
15130 ÷ 123.50 +
159.36 ÷ 10.25 = ?
145
[÷]
[=]
145.0000
11.8367
145.0000 ÷
12.2500 =
11.8367 +
12.25
15130 [÷]
123.50 [=]
15,130.0000
122.5101
15,130.0000 ÷
123.5000 =
122.5101 +
159.36 [÷]
159.3600
15.5473
10.25
[=]
159.3600 ÷
10.2500 =
15.5473 +
[T]
149.8941
149.8941 T
17
16. UNIT / PRICE CALCULATION
Decimal
Rounding
Σ
GT
Print
A
5/4
Σ
.
PRINT
Calculation
Enter
132
Display
132.00
748.44
Paper
132 x $5.67 = $748.44
146 x $4.45 = $649.70
155 x $3.11 = $482.05
Total = ?
[x]
[=]
132.00 x
5.67 =
567
748.44 +
146
445
[x]
[=]
146.00
649.70
146.00 x
4.45 =
155
311
[x]
[=]
155.00
482.05
649.70 +
155.00 x
3.11 =
[T]
1,880.19
482.05 +
1,880.19 T
17. TAX RATE PRESETTING
Decimal
Rounding
Σ
GT
Print
2
↑
.
.
PRINT
Calculation
Enter
Display
0.
Paper
[CE/C]
Preset TAX 1 = 7.5% (Press & Hold 3 sec)[RATE]
0. C
(Blinking) 0.
7.50
…1…
7.5
[TAX 1]
7.50 %
0. C
[CE/C]
0.
(Blinking) 0.
18.60
Preset TAX 2 = 18.6% (Press & Hold 3 sec)[RATE]
18.6 [TAX 2]
…2…
18.60 %
18
18. TAX CALCULATION
Decimal
Rounding
Σ
GT
Print
2
↑
.
.
PRINT
Calculation
Enter
Display
0.
Paper
Price without Tax 1
=261.56
[CE/C]
0. C
261.56 [TAX 1]
[+]
261.56
281.18
261.56
Price with Tax 1 = ?
…1…
7.50 %
19.62 Δ
281.18 ∗
281.18
Price without Tax 1
[TAX 1]
281.18
261.56
…1…
[−]
7.50 %
19.62 Δ
261.56 ∗
0. C
Price without Tax 2
=300
[CE/C]
0.
300.
300
[TAX 2]
300.00
Price with Tax 2 = ?
[+]
355.80
…2…
18.60 %
55.80 Δ
355.80 ∗
355.80
Price without Tax 2
[TAX 2]
355.80
300.00
…2…
[−]
18.60 %
55.80 Δ
300.00 ∗
19
Calculation
Enter
Display
Paper
VAT including TAX 1 and TAX 2:
200
200.00
[TAX 1]
[TAX 2]
[+]
200.
…1…
200.
7.50 %
15.00 Δ
252.20
…2…
18.60 %
37.20 Δ
…1,2…
52.20 Δ
252.20 ∗
Price excluding TAX 1 and TAX 2:
[TAX1]
[TAX2]
[−]
252.20
252.20
200.00
252.20
…1…
7.50 %
15.00 Δ
…2…
18.60 %
37.20 Δ
…1,2…
52.20 Δ
200.00 ∗
NOTE: TAX calculation is fix to 2 decimal points and the result
will be rounded up.
19. PERCENT ADD ON
Decimal
Rounding
Σ
GT
Print
2
↓
.
.
PRINT
Calculation
Enter
3.95
Display
3.95
Paper
Price = $3.95
[x]
3.95
5.00 %
0.19
x
Discount = 5%
Tax Amount = $0.19
Net Amount= $4.14
5
[%+]
0.19
∗
[+]
4.14
4.14 +%
20
20. PERCENT DISCOUNT
Decimal
Rounding
Σ
GT
Print
2
5/4
.
.
PRINT
Calculation
Enter
Display
169.50
23.73
Paper
Price = $169.50
Discount = 14%
Discount Amount = $23.73
Net = $145.77
169.5
14
[x]
169.50 x
14.00 %
23.73 ∗
[%+]
[−]
145.77
145.77 -%
21. CHAIN DISCOUNT WITH TOTAL AMOUNT OF DISCOUNT
Decimal
Rounding
Σ
GT
Print
2
5/4
.
.
PRINT
Calculation
Enter
23.15
Display
23.15
23.15
3.47
Paper
$23.15 less 15/10/5% =
$16.82 Net
[M+]
[x]
23.15 M+
M
M
23.15
15.00 %
3.47
x
Total Amount of
Discount $6.33
15
10
5
[%+]
∗
[−]
M
19.68
19.68 -%
[x]
M
M
19.68
1.97
19.68 x
10.00 %
[%+]
1.97
∗
[−]
M
17.71
17.71 -%
[x]
M
M
17.71
0.89
17.71 x
5.00 %
[%+]
0.89
∗
[−]
M
M
16.82
16.82 -%
[M−]
[MT]
16.82
6.33
16.82 M−
6.33 MT
21
22. PERCENT CHANCE AND AMOUNT OF DIFFERENCE
Decimal
Rounding
Σ
GT
Print
2
5/4
.
.
PRINT
Calculation
Enter
Display
60.00
Paper
Last Year’s Expense $60.00
This Year’s Expense $130.00
Amount of Difference $70.00
Percent of Chance 116.67%
60
[Δ%]
[=] / [%+]
60.00
130.00
Δ
=
130
116.67
70.00 Δ∗
116.67 Δ%
23. CONSTANT PERCENT CHANGE AND AMOUNT OF DIFFERENCE
Decimal
Rounding
Σ
GT
Print
2
5/4
.
.
PRINT
Calculation
Enter
125000
Display
Paper
Last Year‘s Expense
$125,000
[Δ%]
[=]
125,000.00
40.00
125,000.00
175,000.00
Δ
=
This Year’s Expense
$175,000
175000
50,000.00 Δ∗
Next Year’s Expense
$210,000
210000
[=]
68.00
40.00 Δ%
210,000.00
=
Percent of Chance ?
85,000.00 Δ∗
Amount of Difference ?
68.00 Δ%
22
24. GROSS PROFIT MARGIN CALCULATION COST-SELL-MARGIN
Decimal
Rounding
Σ
GT
Print
0
5/4
.
.
PRINT
Calculation
Cost = 100
Margin = 20%
Sell = ?
Enter
100
20
Display
100.
Paper
[COST]
100.
C
20. M%
25. Δ∗
[MARGIN]
125.
125.
S
Cost = 100
Sell = 125
Margin = ?
100
125
[COST]
[SELL]
100.
20.
100.
125.
C
S
25. Δ∗
20. M%
Sell = 125
Margin = 20%
Cost = ?
125
20
[SELL]
125.
100.
125.
S
20. M%
25. Δ∗
0
[MARGIN]
100.
C
25. MARKDOWN AND SELLING PRICE
Decimal
Rounding
Σ
.
GT
.
Print
PRINT
2
5/4
Calculation
Enter
Display
100.00
- 6.5
Paper
Item Cost $100
100
6.5
[COST]
100.00
C
6.50 M%
6.10 Δ∗
Markdown (Percent) 6.5%
(Base on to be
[+/-]
[MARGIN]
93.90
determined selling price)
Markdown (Amount) $ 6.10
Selling Price $ 93.90
93.90
S
23
26. SQUARE ROOT-You can use the ÷ and = key to calculate square root
Decimal
Rounding
Σ
GT
Print
2
5/4
.
.
PRINT
Calculation
Enter
Display
Paper
58.00
58.00 R
7.62
÷
58 = 7.62
58
[÷]
[=]
58.00
7.62
∗
27. INVOICE – INVOICE NUMBER 88901; DATE 10/3/04
Decimal
Rounding
Σ
GT
Print
A
5/4
Σ
.
PRINT
Calculation
Enter
88901
10.3.04 [#/S]
Display
88,901.
10.304
16.00
Paper
Quantity Price Net
[#/S]
# 88901
# 10.03.04
16
3.29 52.64
1.39 150.12
202.76
16.00 x
3.29 =
108
Gross
16
[x]
[=]
3.29
52.64
52.64 +
Less 10% Discount
- 20.28
108
[x]
[=]
108.00
150.12
108.00 x
1.39 =
150.12 +
182.48
+ 9.12
191.60
1.39
Tax 5%
Net
[T]
202.76
202.76 T
[x]
202.76
20.28
10
5
[%+]
202.76 x
10.00 %
20.28 +
[−]
182.48
182.48 -%
[x]
182.48
9.12
[%+]
182.48 x
5.00 %
9.12 +
[+]
191.60
0.
[CE/C]
191.60 +%
0. C
24
28. PAYROLL
Decimal
Rounding
Σ
GT
Print
2
5/4
Σ
.
PRINT
Calculation
Given
Find
Regular Pay
Total Deductions $ 44.12
$ 5.75 Hourly Rate
38 Hours Worked
7.15% FICA
$ 218.50
Net Pay
$ 174.38
$ 23.75 Withholding
$ 4.75 Insurance
Calculation
See Above
Enter
5.75
Display
Paper
[x]
5.75
5.75
38.00
x
38
[M+]
M
218.50
=
218.50 M+
[x]
M
M
218.50
15.62
7.15
[%+]
218.50 x
7.15 %
23.75
4.75
[+]
[+]
[T]
M
M
M
39.37
44.12
44.12
15.62 +
23.75 +
4.75 +
[M−]
[MT]
M
44.12
44.12 T
174.38
44.12 M-
174.38 MT
25
29. MEMORY CALCULATION
Decimal
Rounding
Σ
GT
Print
F
5/4
.
.
PRINT
Calculation
Enter
Display
0.
Paper
[CE/C]
[+]
0. C
100. +
200. +
300. T
100 + 200 = ?
900 - 500 = ?
100
200
100.
300.
300.
[+]
20 X 7
12 X 5
Total
= ?
= ?
?
[T]
[M+]
[+]
M
300.
900.
400.
400.
300. M+
900. +
900
500
M
M
M
[−]
[T]
500.
−
400. T
[M+]
[X]
M
M
M
400.
20.
400. M+
20
7
20.
7.
x
=
∗
[=]
140.
140.
[M+]
[X]
M
M
M
140.
12.
140. M+
12
5
12.
5.
x
[M+]
60.
=
60. M+
[MS]
[MT]
M
900.
900.
900. MS
900. MT
26
30. SETTING THE DATE
Set Slide Switches as Example Below:
EXAMPLE: Set DATE to September 14, 2004 (09-14-04)
Step
1.
Enter
Depress This Key
Your Display Will Show
Tape Will Read
Clear Key (CE/C)
0.
0.C
TIME/DATE Key and hold until
Flashing Numbers in This Format -
MM-DD-YYYY
2.
display flashes
3.
4.
5.
6.
09
14
04
9
914
91404
Tap TIME/DATE Key
09-14-2004
7.
#/S Key
09-14-2004
# 9.14.2004
Decimal
Rounding
Σ
.
GT
.
Print
PRINT
2
5/4
1. Depress the CE/C key. Your display with show 0. and the tape will read 0.C.
2. Depress the TIME/DATE key and hold until the display is flashing.
3. Enter the month, in our example, 09. Your display will show 9.
4. Enter the day, in our example, 14. Your display will show 914.
5. Enter the year, in our example 2004, as 04. Your display will show 91404.
6. Tap the TIME/DATE key to set the DATE. Your display will now show 09-14-2004.
7. To PRINT the DATE, depress the (#/S) key, your tape will show # 9.14.2004.
NOTE: The only key to enter the Date/Time display mode is the TIME/DATE key. The only
key to exit the Time/Date display mode is the CE/C.
27
31. SETTING THE TIME
Set Slide Switches as Example Below:
EXAMPLE: Set TIME to 4:37 PM
Step #
1.
Enter
Depress This Key
Your Display Will Show
Tape Will Read
Clear Key (CE/C)
0.
0.C
TIME/DATE Key and hold
Flashing Numbers in This Format -
MM-DD-YYYY
2.
3.
until display flashes
Tap TIME/DATE key to
switch to Time Mode
Flashing Numbers in This
Format – HH-MM-SS
4.
5.
6.
16
37
16
1637
Tap TIME/DATE Key
P 04-37-00
7.
#/S Key
P 04-37-00
#•04 •37
Decimal
Rounding
Σ
.
GT
.
Print
PRINT
2
5/4
1. Depress the CE/C key. Your display with show 0. and the tape will read 0.C.
2. Depress the TIME/DATE key and hold until the display is flashing.
3. Tap the TIME/DATE key to go to Time Mode.
4. Enter the hour, in our example 16 in military time. Your display will show 16.
5. Enter the minutes, in our example 37. Your display will show 1637.
6. Tap the TIME/DATE key to set the TIME. Your display will now show P 04-37-00 and the
seconds will begin counting.
7. To PRINT the TIME, depress the (#/S) key, your tape will show #•04•37.
NOTE: On the PRINT on the paper tape, the dot in front (#•07•05) means PM, there will
be no dot printed for AM.
28
TECHNICAL SPECIFICATIONS
Type:
Basic Operations:
Capacity:
Desktop Adding Machine/Calculator, Electronic Print/VFD
Addition/subtraction and multiplication/division
Input and result 12 digits.
Decimal System:
Functions:
Add Mode(A), Floating(F), Fixed(0,2,3,4)
4 rules, successive calculation, memory calculation, grand
total or sigma calculation, constant calculations, 2 tax
calculation, delta percentage calculation, cost, sell and margin
calculation.
Printer:
Power Consumption:
Ink:
Character wheel selection type.
11 W
VICTOR Twin Spool Ribbon #7010
Width 57.5 ± 0.5mm X Diameter 50mm
12 digit VFD display.
Paper width:
Display:
Operating Temp:
Dimensions:
Weight:
32°~104°F, 0°C ~ 40°C
L295 X W210 X H72 mm
1.53 kg
29
WARRANTY
Your new VICTOR electronic calculator is guaranteed to the original purchaser for three (3) years
for all parts and labor, providing repair work is performed at an authorized VICTOR Regional
Service Center and the unit is sent prepaid. Warranty repair requires a copy of the original
purchase invoice or receipt to be packed with the machine. The address and phone number of our
National Service Depot is below.
Any warranty, statutory or otherwise, does not include service and/or replacement or
repair of parts when damage or defect is a result of accident, abuse, or the elements.
GARANTIE
Votre nouvelle calculatrice électronique VICTOR est garantie au premier acheteur pendant une
période de trios ans pour toutes les pieces et la main
d’œuvre, à condition que les reparations soient effectuées dans un Centre de Service
Régional VICTOR autorisé et que l’appareil soit envoyé par courier affranchi. Pour
les Centres de Service situés à l’extérieur deś Etats-Unis, veuillez counsulter votre
distributeur de fournitures de bureau local ou le site Web de VICTOR. Pour qu’une
reparation soit couverte par la garantie, il faut joindre la facture ou le reçu d’achat
avec l’appareil.
Toute garantie, légale ou autre, n’inclut pas l’entretien et/ou le remplacement ou la
reparation de pieces lorsque le dommage ou la défectuosité est dû à un accident, à un
mauvais usage ou aux éléments.
LA GARANTÍA
Su nueva calculadora electronica de VICTOR se garantiza a el comprador original durante tres
años para todas las partes y labora, mientras proporcionando el trabajo del la reparación ha
realizado en un Centro Regional de Reparaciones autorizado por VICTOR y la unidad se envía por
el correo pagado por adelantado. Para los Centros de Servicio fuera del EE.UU por favor
consultan su suministro de la ofician local distribuidor o VICTOR Web Site. La reparación de la
garantía requiere una copia de la factura de la compra original o recibo ser condensado con la
máquina.
Cualquier garantía, estatutario o por otra parte, no incluya el servicio y o reemplazo o reparación
de partes cuando daño o defecto es un resultado de accidente, abuse,
o los elementos.
Victor Technology
780 West Belden Avenue
Addison, IL 60101 USA
Telephone: 800-628-2420
Fax: 630-268-8450
30
REGISTER ON LINE AT www.victortech.com
Or
FILL OUT THIS FORM AND MAIL TO THE ADDRESS ON BACK
Date Purchased: ___________________ Model No.___________Serial No._______________
User’s Name: __________________________________________________________________
Company Name (if applicable): ___________________________________________________
Address: ______________________________________________________________________
City: ____________________________________ State: _______________ Zip: ____________
Purchased From: _______________________________________________________________
Address: ______________________________________________________________________
City: ____________________________________ State: _______________ Zip: ____________
*****************************************************************************
VICTOR EXTENDED PROTECTION PROGRAM
ONLY $25.00
Act now and extend your VICTOR warranty for another full year!
Covers all parts and labor.
Name: ______________________________________ Date: ____________________
Address: ______________________________________________________________
City: ________________________________ State: ___________ Zip: ____________
To receive repair coverage on your VICTOR calculator for one full year from expiration of VICTOR’S 3 year
warranty, enclose this form and proof of purchase (invoice) showing your name, complete address, model and
serial number along with your check or money order for $25.00 payable to: Victor Technology, Attn: Extended
Warranty Dept., 780 West Belden, Addison, IL 60101.
VICTOR will acknowledge receipt, send you an authorized coverage agreement, and provide the address of the authorized
VICTOR Regional Service Center nearest you.
Repair necessitated by accident or abuse is excluded.
If repairs are needed during the coverage period, ship your VICTOR calculator to the nearest authorized VICTOR Regional Service
Center, freight PREPAID. It will be promptly repaired and returned to you freight prepaid.
31
Place
Stamp
Here
Retain packing box and materials. Offer void 30 days after Purchase.
Victor Technology
780 West Belden Avenue
Addison, IL 60101
32
Corporate Office
And
National Service Office
VICTOR TECHNOLOGY
780 W. Belden Avenue
Addison, IL 60101
Phone: 630-268-8400
Fax: 630-268-8450
|