Topfield High Defninition Digital Satellite Receiver HV7700 HSCI User Manual

TOPFIELD  
TF 7700 HSCI  
User Guide  
High Definition  
Digital Satellite Receiver  
Common Interface  
Contents iii  
Contents  
1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
1
1
2
2
4
6
1.2 Controlling the digital receiver . . . . . . . . . . . . . . . . . .  
1.2.1 The front panel . . . . . . . . . . . . . . . . . . . . . . .  
1.2.2 The remote control . . . . . . . . . . . . . . . . . . . . .  
1.3 What is common interface? . . . . . . . . . . . . . . . . . . . .  
7
7
7
9
2.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
2.2 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . .  
2.3 Rear panel connections . . . . . . . . . . . . . . . . . . . . . . .  
2.4 Connecting up your digital receiver . . . . . . . . . . . . . . . 10  
2.4.1 Connecting the antenna . . . . . . . . . . . . . . . . . . 10  
2.4.2 Connecting to your television . . . . . . . . . . . . . . 11  
15  
3.1 Language settings . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
3.2 Video and audio settings . . . . . . . . . . . . . . . . . . . . . . 16  
3.2.1 Colour model . . . . . . . . . . . . . . . . . . . . . . . . 16  
iv Contents  
3.2.2 Video cassette recorder . . . . . . . . . . . . . . . . . . 17  
3.2.3 Television aspect ratio . . . . . . . . . . . . . . . . . . . 17  
3.2.4 High definition television . . . . . . . . . . . . . . . . . 18  
3.2.5 Sound mode . . . . . . . . . . . . . . . . . . . . . . . . 19  
3.3 Local time setting . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
3.4 Parental control . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
3.5 Adjusting the on-screen display . . . . . . . . . . . . . . . . . . 23  
24  
4.1 Searching broadcasting services . . . . . . . . . . . . . . . . . . 24  
4.1.1 Configuring LNB settings . . . . . . . . . . . . . . . . . 24  
4.1.2 Configuring DiSEqC 1.2 settings . . . . . . . . . . . . . 26  
4.1.3 Configuring USALS settings . . . . . . . . . . . . . . . 28  
4.1.4 Searching services . . . . . . . . . . . . . . . . . . . . . 29  
4.2 Editing the transponder list . . . . . . . . . . . . . . . . . . . . 32  
4.3 Resetting to factory settings . . . . . . . . . . . . . . . . . . . . 33  
4.4 Resetting to installer settings . . . . . . . . . . . . . . . . . . . 33  
35  
5.1 Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
5.2 Watching television . . . . . . . . . . . . . . . . . . . . . . . . . 35  
5.2.1 The services list . . . . . . . . . . . . . . . . . . . . . . . 35  
5.2.2 The favourite services list . . . . . . . . . . . . . . . . . 38  
5.2.3 Viewing programme information . . . . . . . . . . . . 39  
5.2.4 Selecting audio tracks . . . . . . . . . . . . . . . . . . . 40  
5.2.5 Selecting subtitle tracks . . . . . . . . . . . . . . . . . . 40  
5.2.6 Viewing teletext . . . . . . . . . . . . . . . . . . . . . . 40  
5.3 Viewing electronic programme guide . . . . . . . . . . . . . . 40  
5.4 Watching multifeed programme . . . . . . . . . . . . . . . . . 42  
5.5 Making timer events . . . . . . . . . . . . . . . . . . . . . . . . 42  
Contents  
v
44  
6.1 Editing the services list . . . . . . . . . . . . . . . . . . . . . . . 44  
6.2 Editing the favourite list . . . . . . . . . . . . . . . . . . . . . . 46  
6.3 How to use on-screen keyboard . . . . . . . . . . . . . . . . . . 48  
6.4 Transferring receiver data . . . . . . . . . . . . . . . . . . . . . 48  
50  
7.1 From a USB storage . . . . . . . . . . . . . . . . . . . . . . . . . 51  
7.2 From your computer via RS-232 port . . . . . . . . . . . . . . . 51  
54  
1
Chapter 1  
Introduction  
The TF 7700 HSCI digital receiver is fully compliant with the  
international Digital Video Broadcasting (DVB) standard, and  
can receive digital broadcasts. For its operation, you need an  
antenna, which must be installed appropriately.  
NOTE  
In general we equate a channel with a frequency. How-  
ever, unlike analogue broadcasts, digital broadcasts are not  
all assigned to their own frequencies; instead, multiple tele-  
vision broadcasts are transmitted through a single frequency.  
The frequency in digital broadcasting is usually called trans-  
ponder. To reduce confusion in this manual, the word service  
is preferably used than channel as a term to indicate one tele-  
vision or radio broadcast.  
1.1 Features  
The TF 7700 HSCI digital receiver has the following features:  
• Supports DiSEqC 1.0, DiSEqC 1.1, DiSEqC 1.2 and US-  
ALS.  
     
2
Introduction  
• Can store up to 5000 television and radio services.  
You can edit the services list.  
You can make a favourite list with your favourite ser-  
vices.  
You can view information about the current television  
or radio programme.  
• Has an electronic programme guide that provides an  
overview of programme schedules for next few hours.  
You can update the firmware of the digital receiver to  
the latest version, which will be provided by the manu-  
facturer.  
1.2 Controlling the digital receiver  
The digital receiver can be operated with the remote control  
and the buttons on the front panel.  
NOTE  
When the digital receiver is off but plugged into a wall outlet,  
we say that it is in standby mode; on the other hand, when it is  
on, it is in operation mode. Even when you are not using the  
digital receiver, you should keep it plugged into a wall outlet  
to be in standby mode so that it can run timer events at any  
time.  
1.2.1 The front panel  
The front panel of the digital receiver has buttons to control  
the digital receiver, and specific lamps and a display to indi-  
cate its status. The following indicates what they mean.  
   
1.2 Controlling the digital receiver  
3
STANDBY button switches the digital receiver between  
standby mode and operation mode.  
CHANNEL  
,
buttons move to the next or previous ser-  
vice. They are also used to navigate in the menus and  
interactive screens.  
VOLUME  
,
buttons increase and decrease the volume.  
They are also used to change options for a menu item.  
Front display displays the current time in standby mode,  
and displays the current service in operation mode.  
4
Introduction  
1.2.2 The remote control  
1
button switches the digital  
receiver between standby mode  
and operation mode.  
1
2
14  
15  
3
4
16  
2
button pauses live television.  
£
3
V.Format button changes video res-  
¢
¡
olution. See § 3.2.4 for more de-  
tails.  
5
17  
18  
6
7
4
Numeric buttons are used to en-  
ter service numbers and menu op-  
tions.  
19  
20  
8
9
21  
5
button switches between the  
current service and the previously  
viewed one.  
10  
10  
22  
20  
11  
12  
13  
6
button displays teletext.  
7
button is used to select an  
audio track and sound mode, or  
a video track of multifeed pro-  
gramme.  
23  
£
8
MENU button displays the main  
¢
¡
menu. It is also used to return  
to the previous menu from a sub-  
menu.  
£
9
OK button displays the services  
list. It is also used to select menu  
items. See § 5.2.1 for more details.  
¢
¡
£
¢
£
¡
10  
V+ , Vbuttons increase and decrease the volume.  
They are also used to change options for a menu item.  
¢
¡ ¢  
¡
£
11  
EXIT button is used to leave the current screen.  
   
1.2 Controlling the digital receiver  
5
12  
These buttons have different functions per menu. They  
will be guided by on-screen help.  
£
13  
SAT button displays the satellite list.  
¢
¡
14  
button mutes the sound. Press again to switch it  
back on.  
£
15  
A/R button changes aspect ratio. See § 3.2.3 for more  
details.  
¢
¡
16  
button switches between television services and ra-  
dio services.  
£
17  
FAV button displays the favourite list.  
¢
¡
18  
button is used to select a subtitle track.  
19  
button sets a sleep timer.  
£
£
20  
P+ , Pbuttons move to the next or previous service.  
They are also used to navigate in the menus and interac-  
tive screens.  
¢
¡ ¢  
¡
£
21  
GUIDE button displays the electronic programme guide.  
¢
¡
22  
button displays more information about the current  
programme or a programme highlighted in the elec-  
tronic programme guide.  
£
23  
AUX button switches the output of the TV SCART socket  
between the digital receiver and the device connected to  
the VCR SCART socket. See § 3.2.2 for more details.  
¢
¡
 
6
Introduction  
1.3 What is common interface?  
Some broadcasts are scrambled so that only  
paid subscribers can enjoy them. Scrambled ser-  
vices can only be viewed with a Conditional Ac-  
cess Module (CAM) and a subscription card be-  
longing with the scrambling system.  
Common Interface (CI) is an interface for condi-  
tional access modules. The front of the digital  
receiver has two common interface slots.  
To watch a pay service, you should take the following steps:  
1. Purchase a conditional access module and a subscrip-  
tion card for the pay service you want to watch.  
2. Insert the subscription card into the conditional access  
module.  
3. Insert the conditional access module into the common  
interface slot on the front of the digital receiver.  
To view the information about  
the module and subscription  
card inserted into the digital re-  
ceiver, select the Common Inter-  
face menu.  
   
7
Chapter 2  
Setup  
2.1 Unpacking  
Before going any further, check that you have received the fol-  
lowing items with your digital receiver.  
• Remote control unit  
• Two batteries for the remote control (AAA 1.5 V)  
• One component cable  
• One HDMI cable (optional)  
• A copy of this user guide  
NOTE  
Accessories may vary according to your local area.  
2.2 Safety precautions  
Please read the following safety precautions carefully.  
• The mains power must be 90 to 250 volt. Check it before  
connecting the digital receiver to the wall outlet. For  
     
8
Setup  
the power consumption of the digital receiver, refer to  
Table 2.1.  
• The wall outlet should be near the equipment. Do not  
run an extention lead to the unit.  
• Do not expose the digital receiver to any moisture. The  
digital receiver is designed for use indoors only. Use dry  
cloth when cleaning the digital receiver.  
• Place the digital receiver on a firm and level surface.  
• Do not place the digital receiver close to heat emitting  
units or in direct sunlight, as this will impair cooling.  
Do not lay any objects such as magazines on the digi-  
tal receiver. When placed in a cabinet, make sure there  
is a minimum space of 10 centimetres around it. For  
the physical specification of the digital receiver, refer to  
Table 2.2.  
• Protect the power cord from being walked on or  
pinched. If wires are exposed or cord is damaged, do  
not use the digital receiver and get cord replaced.  
• Never open the digital receiver casing under any cir-  
cumstances. Warranty will be void.  
• Refer all servicing to a qualified service technician.  
Table 2.1: Power specification  
Input voltage  
90 to 250 V AC, 50/60 Hz  
Power consumption 37 W at maximum in operation  
8 W in standby  
Table 2.2: Physical specification  
Size  
Weight  
430× 60× 265 mm  
2.9 kg  
Operating temperature  
Storage relative humidity  
0 to 45 °C  
5 to 95 %  
     
2.3 Rear panel connections  
9
2.3 Rear panel connections  
The TF 7700 HSCI has some connections on the back panel.  
1
5
8
VIDEO  
LNB IN  
Y
TV  
L
Pb  
Pr  
R
YPbPr  
SCART  
LNB OUT  
AUDIO  
S/PDIF  
HDMI  
RS-232  
USB  
VCR  
2
3
4
6
7
9
10 11  
12  
Check what connections your television set has in comparison  
with the digital receiver.  
1
LNB IN Satellite broadcasting signal input socket.  
2
LNB OUT Satellite broadcasting signal output socket  
through the LNB IN socket for another digital re-  
ceiver.  
3
YPbPr SCART Video output selection switch. See  
§ 3.2.4 for for more details.  
4
HDMI Audio and video output socket for the high defi-  
nition television set.  
5
VIDEO Composite video output socket for the television  
set. (yellow)  
6
AUDIO L/R Stereo audio output socket for the television  
set or audio system. (white/red)  
7
Y/Pb/Pr Component video output socket for the televi-  
sion set. (green/blue/red)  
8
TV Audio and video output socket for the television set.  
9
VCR Audio and video input/output socket for the  
video cassette recorder or suchlike.  
 
10 Setup  
10  
S/PDIF Dolby digital output socket for the audio sys-  
tem.  
11  
RS-232 Serial port for firmware update and data trans-  
fer.  
12  
USB USB port for firmware update and data transfer.  
Table 2.3: Connectors specification  
HDMI  
High definition video output  
Left & right audio output  
Dolby digital audio output  
VIDEO  
AUDIO  
YPbPr  
TV  
composite video (CVBS) output  
Left & right audio output  
Component video (YUV) output  
CVBS/S-Video/RGB/YUV video output  
Left & right audio output  
VCR  
CVBS video output  
Left & right audio output  
CVBS/S-Video/RGB/YUV video input for bypass  
Left & right audio input for bypass  
Dolby digital audio output  
S/PDIF  
RS-232 115.2 kbps at maximum  
USB 2.0  
2.4 Connecting up your digital receiver  
There are several ways to set up the digital receiver. Set up  
the digital receiver suitably to your television and other appli-  
ances. If you have any problem with your setup or need help,  
contact your dealer.  
2.4.1 Connecting the antenna  
Whatever sort of connection you have between the digital re-  
ceiver and the television, you need to connect the digital re-  
ceiver to your television antenna so that it can receive digital  
television services.  
     
2.4 Connecting up your digital receiver 11  
Connect the antenna cable to the LNB IN  
socket.  
If you have another digital receiver, link it  
from the LNB OUT connector.  
2.4.2 Connecting to your television  
Between all the following connectors of your digital receiver,  
we recommend you use the first connector to get best picture  
quality. If your television does not have the matching connec-  
tor then use the next connector in the following order for best  
picture quality.  
1. HDMI connector (HDMI)  
2. SCART connector (TV)  
3. Component connector (YPbPr)  
4. Composite connector (VIDEO)  
You should configure audio and video settings after connect-  
ing up the digital receiver. See § 3.2 for detailed description.  
To use the HDMI connector  
If you have a high definition television set,  
you should use a HDMI cable for best re-  
sults. Plug one end of the cable into the  
HDMI socket on the digital receiver, and the  
other end into the matching socket on your  
television. In this case, you do not have to  
make audio connections because the HDMI  
connector can output stereo audio or Dolby  
digital audio.  
   
12 Setup  
To use the SCART connector  
For best results with a standard television  
set, you should use a SCART cable, plugging  
one end into the TV socket on the digital re-  
ceiver and the other end into a free SCART  
socket on your television.  
Some televisions have inputs via Com-  
ponent or S-Video connectors rather than  
SCART.  
If you have such a television, use an appropriate conversion  
cable to link the TV socket on the digital receiver to the match-  
ing socket on your television.  
If you connect with a standard SCART cable, you do not have  
to make audio connections because the SCART connector can  
output stereo audio. But if you use a conversion cable, such as  
SCART-to-Component, you have to make audio connections.  
NOTE  
You cannot view high definition video with the SCART con-  
nector.  
To use the component video connector  
You will need to obtain a component video  
cable (RCA cable) to use the component  
video connector. Plug one end of the ca-  
bles into the Y (green), Pb (blue) and Pr (red)  
sockets on the digital receiver, and the other  
end into the matching sockets on your tele-  
vision.  
Y
b
P
P
r
 
2.4 Connecting up your digital receiver 13  
To use the composite video connector  
You will need to obtain a composite video  
cable (RCA cable) to use the composite video  
connector. Plug one end of the cable into  
the VIDEO (yellow) socket on the digital re-  
ceiver, and the other end into the matching  
socket on your television.  
NOTE  
You cannot view high definition video with the composite  
video connector.  
To connect the audio connectors  
You will need to obtain an audio cable (RCA  
cable) to connect the audio connectors. Plug  
one end of the cable into the AUDIO L  
(white) and AUDIO R (red) sockets on the  
digital receiver, and the other end into the  
matching sockets on your television or au-  
dio system.  
To enjoy Dolby digital audio, your televi-  
sion or audio system must be able to decode  
Dolby digital audio, and you will need to ob-  
tain a S/PDIF cable. Plug one end of the ca-  
ble into the S/PIDF socket on the digital re-  
ceiver, and the other end into the matching  
socket on your audio system.  
2.4.3 Connecting to your video cassette recorder  
The digital receiver can also output video to another appliance  
such as a video cassette recorder or video receiver through an  
auxiliary SCART connector.  
   
14 Setup  
You will need to obtain a SCART cable to  
use the auxiliary SCART connector. Plug  
one end of the cable into the VCR socket on  
the digital receiver, and the other end into  
the matching socket on your video cassette  
recorder or suchlike.  
2.4.4 Inserting batteries in the remote control  
To insert the batteries, open the battery compartment by re-  
moving the lid, and then insert the batteries observing the po-  
larity, which is marked on the base of the battery compart-  
ment.  
If the digital receiver no longer reacts properly to remote con-  
trol commands, the batteries may be flat. Be sure to remove  
used batteries. The manufacturer accepts no liability for dam-  
age resulting from leaking batteries.  
NOTE  
Batteries, including those which contain no heavy metals, may  
not be disposed of with household waste. Please dispose of  
used batteries in an environmentally sound manner. Find out  
about the legal regulations which apply in your area.  
   
15  
Chapter 3  
Preference Settings  
3.1 Language settings  
You can select the language in  
which the menu would be dis-  
played. In addition to that, you  
can select which language of au-  
dio track as well as of subtitle  
track to be output.  
Select the System Setting >  
Language Setting menu. You  
should see a screen like the left  
figure.  
Menu language  
The digital receiver supports many menu languages: Dutch,  
English, German, French, Italian, Russian, Turkish and so  
forth. Set the Menu Language option to your desired lan-  
guage. Once you select a language, the menu will be immedi-  
ately displayed in the selected language.  
     
16 Preference Settings  
Subtitle language  
Set the Subtitle Language option to your desired language.  
When you watch a programme, the subtitle track of the se-  
lected language will be displayed if available.  
Apart from this setting, you can select a subtitle track with the  
button. See § 5.2.5 for further information.  
Audio language  
Set the Audio Language option to your desired language.  
When you watch a programme, the audio track of the selected  
language will be output if available.  
Apart from this setting, you can select an audio track with the  
button. See § 5.2.4 for further information.  
3.2 Video and audio settings  
You have to configure the video  
and audio settings appropri-  
ately to your television set and  
appliances.  
Select the System Setting >  
A/V Output Setting menu. You  
should see a screen like the left  
figure.  
3.2.1 Colour model  
Through the TV SCART connector, the digital receiver is able  
to output video in various colour models. If you have the dig-  
ital receiver linked to your television via this connector, you  
should set the SCART Output option to your desired colour  
model. If you have connected via the RCA connector labeled  
     
3.2 Video and audio settings 17  
VIDEO on the back panel, you do not have to set this option  
because the digital receiver outputs CVBS video through the  
RCA connector independent of SCART connector.  
It is known in general that the RGB colour model provides the  
best video quality with little difference from the YUV colour  
model but the CVBS colour model does the least. So RGB  
would be most desirable for this option.  
3.2.2 Video cassette recorder  
You can have the digital receiver linked to your video cassette  
recorder or such an appliance via the VCR SCART connec-  
tor. In that case, the digital receiver will operate differently  
depending on the setting of the VCR Scart Type option. If  
the option is set to Standard, the digital receiver will pass the  
video from the video cassette recorder to your television when  
it starts playback. But if the option is set to External A/V, the  
digital receiver will not pass the video automatically. To pass  
£
it, you have to press the AUX button.  
¢
¡
3.2.3 Television aspect ratio  
If you have a wide-screen television, set the TV Aspect Ratio  
option to 16:9.  
Otherwise, if you have a normal-screen television, set the TV  
Aspect Ratio option to 4:3.  
You cannot fully enjoy wide-screen programmes with your  
normal-screen television as the above figures show. The left  
figure shows a normal picture displayed in the normal screen.  
To watch wide-screen programmes in the shape like the center  
     
18 Preference Settings  
figure, set the 16:9 Display Format option to Letter Box. Wide-  
screen pictures then will be reduced to fit to the width of the  
normal screen. Otherwise, to watch them in the shape like the  
right figure, set it to Center extract. Wide-screen pictures then  
will be cut out on the left and right sides equally to fit to the  
width of the normal screen.  
3.2.4 High definition television  
The digital receiver supports various video resolutions from  
576 to 1080. In general a resolution of 720 or more is consid-  
ered high definition. The higher the resolution is, the better  
quality you can enjoy. However, if your television set does  
not support high definition, you cannot enjoy high definition  
quality picture.  
Set the Video Format option as you desire. If you set this  
option to 576P, the digital receiver will present even high def-  
inition programmes in resolution of 576. On the contrary, if  
you set it to 1080I, the digital receiver will present even stan-  
dard definition programmes in resolution of 1080. It is rec-  
ommended to set it to Auto if you have a high definition tele-  
vision. With that setting the digital receiver will present a pro-  
gramme as it is without any resolution conversion. You can  
£
change the resolution with the V.Format button when you are  
watching a programme. Whenever you press it, the video res-  
olution is changed in turn.  
¢
¡
If you have the digital receiver linked to your television  
via the component video connectors (Y, Pb and Pr) or  
the HDMI connector you have to toggle the video out-  
put selection switch on the back panel to the YPbPr po-  
sition. Otherwise if you have connected it to your tele-  
vision via the TV SCART connector, you have to toggle  
ART  
SC  
the switch to the SCART position. The available values  
of the Video Format option vary depending on which  
position you toggle the switch to.  
YPbPr  
   
3.3 Local time setting 19  
NOTE  
You can enjoy only standard definition video with the follow-  
ing connectors:  
• Composite video connector (VIDEO)  
• SCART connector (TV)  
3.2.5 Sound mode  
Basically, there are two audio sources as you can find two au-  
dio sockets on the back panel of the digital receiver. You can  
enjoy only one source or both of them in either stereo or mono.  
Set the Sound Mode option as you desire.  
Apart from this setting, you can change the sound mode with  
the  
button. See § 5.2.4 for detailed description.  
The digital receiver can output two types of digital audio sig-  
nals via the S/PDIF connector. One is an encoded signal, and  
the other is a decoded signal. If your digital audio appliance  
does not have a Dolby Digital decoder, you have to set the  
Dolby Digital option to PCM. Otherwise, set it to Bitstream.  
3.3 Local time setting  
You should set your local time for timer events. If you do not  
set the local time right, the programme time table provided by  
the programme guide may be distrustful. For the programme  
guide, refer to § 5.3.  
     
20 Preference Settings  
Select the System Setting >  
Time Setting menu. You should  
see a screen like the left figure.  
You can make the local time to  
be automatically set by using  
Greenwich Mean Time (GMT).  
To use Greenwich mean time,  
take the following steps:  
1. Set the Mode option to Auto; then the Time Offset option  
becomes enabled.  
2. Set the Time Offset option to the time difference between  
your time zone and GMT referring to Table 3.1.  
3. To get Greenwich mean time, set the GMT Collection op-  
tion to one among the following:  
Normal from all transponders  
CAS TP from transponders of pay services  
User Select from transponders specified by you  
If you set it to User Select, then the Satellite and Trans-  
ponder options become enabled. Select your desired  
satellite and transponders at those options. With the  
above settings, the digital receiver will scan all trans-  
ponders specified one by one until to get the Greenwich  
mean time.  
4. Make sure that your local time is correctly displayed on  
the Local Time option.  
To set the local time yourself, set the Mode option to Man-  
ual and enter your local time into the Local Time option with  
the numeric buttons. The time format is day/month/year 24-  
hour:minute.  
 
3.3 Local time setting 21  
Table 3.1: Time offset table  
Time offset City  
GMT 12:00 Eniwetok, Kwajalein  
GMT 11:00 Midway Island, Samoa  
GMT 10:00 Hawaii  
GMT 09:00 Alaska  
GMT 08:00 Pacific Time US, Canada  
GMT 07:00 Mountain Time US, Canada  
GMT 06:00 Central Time US, Canada, Mexico City  
GMT 05:00 Eastern Time US, Canada, Bogota, Lima  
GMT 04:00 Atlantic Time Canada, La Paz  
GMT 03:30 Newfoundland  
GMT 03:00 Brazil, Georgetown, Buenos Aries  
GMT 02:00 Mid-Atlantic  
GMT 01:00 Azores, Cape Verde Islands  
GMT  
London, Lisbon, Casablanca  
Paris, Brussels, Copenhagen, Madrid  
South Africa, Kaliningrad  
Baghdad, Riyadh, Moscow, St. Petersburg  
Tehran  
Abu Dhabi, Muscat, Baku, Tbilisi  
Kabul  
Ekaterinburg, Islamabad, Karachi, Tashkent  
Bombay, Calcutta, Madras, New Delhi  
Almaty, Dhaka, Colombo  
GMT + 1:00  
GMT + 2:00  
GMT + 3:00  
GMT + 3:30  
GMT + 4:00  
GMT + 4:30  
GMT + 5:00  
GMT + 5:30  
GMT + 6:00  
GMT + 7:00  
GMT + 8:00  
GMT + 9:00  
GMT + 9:30  
Bangkok, Hanoi, Jakarta  
Beijing, Perth, Singapore, Hong Kong  
Tokyo, Seoul, Osaka, Sapporo, Yakutsk  
Adelaide, Darwin  
GMT + 10:00 Eastern Australia, Guam, Vladivostok  
GMT + 11:00 Magadan, Solomon Islands, New Caledonia  
GMT + 12:00 Fiji, Auckland, Wellington, Kamchatka  
If daylight saving time is observed in your state at the mo-  
ment, set the Daylight Saving Time option to On.  
NOTE  
Daylight saving adds one hour to the time when the option is  
set to On, and it removes one hour when the option is set to  
Off. When setting time offset via Greenwich Mean Time, make  
sure time does not include daylight saving.  
   
22 Preference Settings  
3.4 Parental control  
In general television programmes are classified according to  
the level of violence, nudity and language of its content. When  
you are watching a programme, you can check its programme  
classification on the information box. For the information box,  
see § 5.2.3.  
You can prevent your children from watching specific pro-  
grammes by specifying a programme classification.  
Select the System Setting >  
Parental Control menu. You  
should see a screen like the  
left figure, and you will be  
asked your Personal Identifica-  
tion Number (PIN). The number  
is initially set to 0000.  
If you wish to restrict 15 or above rated programmes, set the  
Censorship option to 15 (age). Setting it to No block restricts  
no programme; on the other hand, setting it to Total block re-  
stricts every programme.  
NOTE  
If a programme does not have any programme classification  
information, your censorship setting will not take effect.  
If anyone is trying to watch a programme that is of or above  
the censorship setting, the person has to enter the personal  
identification number to override.  
To change the number, select the Change PIN Code menu;  
then an input box appears. You have to enter a desired num-  
ber twice for confirmation.  
   
3.5 Adjusting the on-screen display 23  
You can also restrict uses of some menus. Selecting the Access  
Control menu displays a list of menus that you can lock. If the  
Time Setting item is set to Locked, you have to enter the per-  
sonal identification number to access the Time Setting menu.  
If you enter a wrong number, you cannot use the menu. To  
release a shut item, set it to Unlocked.  
3.5 Adjusting the on-screen display  
You can adjust the transparency level of the on-screen display.  
Select the System Setting menu and set the OSD Transparency  
option as you desire. Its available range is from 0 to 50 percent.  
You can adjust the display time of the information box. For  
the information box, see § 5.2.3. To adjust its display time,  
select the System Setting menu and set the Info Box Display  
Time option as you desire. Its available range is from 1 to 30  
seconds. If you set this option to No Info Box, the information  
box will not be displayed when you switch services. However,  
pressing the  
button will display the information box. If you  
set this option to Never Hide, the information box will always  
be displayed.  
In addition, you can raise or lower the position of the informa-  
tion box. Select the System Setting menu and set the Info Box  
Position option as you desire. Its available range is from 10  
to +3 line. The more high the value is set, the more low the  
information box will be positioned.  
   
24 Service Search  
Chapter 4  
Service Search  
After connecting up the digital receiver, you will need to per-  
form a service search.  
4.1 Searching broadcasting services  
This digital receiver can be operated with both fixed and mo-  
torized antenna system. You have to configure antenna set-  
tings according to your antenna system in the following order:  
1. Configure LNB settings. (Refer to § 4.1.1.)  
2. Set the position of your desired satellites if you have a  
motorized antenna. You can control the antenna in DiS-  
EqC 1.2 mode or USALS mode. Refer DiSEqC 1.2 to  
§ 4.1.2, and refer USALS to § 4.1.3.  
3. Perform service search.  
4.1.1 Configuring LNB settings  
There are in large two frequency bands for satellite broadcasts.  
One is C band which ranges approximately from 4 to 6 GHz.  
       
4.1 Searching broadcasting services 25  
The other is Ku band which ranges approximately from 12 to  
18 GHz.  
The LNB (Low Noise Block converter)  
is used to take a wide band of rel-  
atively high frequencies, amplify and  
convert them to similar signals carried  
at a much lower frequency, which is  
called IF (Intermediate Frequency).  
LNB  
High frequencies from satellites are  
converted into 950 to 2150 MHz by a  
LNB.  
Select the Installation > LNB  
Setting menu to configure the  
LNB settings. You should see  
a screen like the left figure.  
£
Pressing the OK button on the Satellite Name option displays  
¢
¡
the satellite list in alphabetic order. Select the satellite toward  
which your antenna is set to face. Even if you cannot find  
your desired satellite, you can add your desired satellite to  
the satellite list. See § 4.2 for detailed description.  
The digital receiver has a database about broadcasting satel-  
lites and their transponders, containing the following infor-  
mation: satellite position, frequency range, symbol rate, po-  
larization and LNB frequency corresponding to the frequency  
range. So you might not have to specify the LNB Frequency  
option. However, if you have selected the Other entry at the  
 
26 Service Search  
Satellite Name option to specify a satellite that is not in the  
satellite list, you might have to fill in the correct LNB fre-  
quency. The absolute difference between a broadcasting fre-  
quency and its LNB frequency must be within 950 to 2150  
MHz. For example, if the frequency band of your desired  
satellite ranges from 3660 to 4118 MHz, you have to set the  
LNB Frequency option to 5150 MHz.  
The LNB has to be supplied with power to operate. Set the  
LNB Power option to On if it does not have any other power  
supply.  
You had better ignore the 22 kHz option.  
The digital receiver is designed to be compatible with DiSEqC  
(Digital Satellite Equipment Control) switches. It is possible  
to connect several antennas to one digital receiver by DiSEqC  
switches. A DiSEqC 1.0 switch allows switching between up  
to 4 satellite sources and a DiSEqc 1.1 switch allows switching  
between up to 16 satellite sources.  
Set the DiSEqC 1.0 and DiSEqC 1.1 options according to your  
antenna configuration.  
For example, to select the antenna con-  
nected to the A5 input in the left fig-  
ure, set the DiSEqC 1.1 option to 2 of  
4 and the DiSEqC 1.0 option to 1 of 4.  
If you have a mini DiSEqC 1.0 switch  
which has only two inputs, you should  
set the DiSEqC 1.0 option to Mini A in-  
stead of 1 of 4.  
4.1.2 Configuring DiSEqC 1.2 settings  
Your motorized antenna will turn toward your desired satel-  
lites horizontally by DiSEqC 1.2.  
   
4.1 Searching broadcasting services 27  
When you switch to an service, if the service is  
provided by a satellite other than current one,  
it will take longer time than usual because the  
antenna has to turn to its position.  
To use the DiSEqC 1.2, select the  
Installation > Motorized DiSEqC  
1.2 menu. You should see a  
screen like the left figure.  
At first you have to set the Mo-  
torized DiSEqC 1.2 option to  
Enable.  
To get the correct position of your desired satellite, perform  
the following steps:  
1. Choose your desired satellite at the Satellite Name op-  
tion.  
2. Set the DiSEqC Command Mode to User.  
3. Select the Goto option at the Motor Control menu. Then  
the antenna will turn toward your selected satellite with  
the position data that the digital receiver has.  
4. If the receiving quality, which is displayed at the bottom  
right of the screen, is not good, tune the antenna finely  
with the options of the Movement menu. If you select  
the 2(E) movement option, the antenna will move to the  
east by two degrees. At this time you had better check  
the receiving quality of every transponder and choose  
the best one at the Transponder (or Frequency) option.  
It will be helpful to your fine tuning.  
 
28 Service Search  
5. Finally select the Store option at the Motor Control menu  
to save the tuned position when the receiving quality  
has turned good.  
There are more motor control options for installers, but this  
manual does not describe them. If you are an installer, refer  
them to the manual for the STAB rotor.  
4.1.3 Configuring USALS settings  
USALS (Universal Satellite Automatic Location System), also  
known as DiSEqC 1.3, calculates the positions of all available  
satellites from your location. Compared to DiSEqC 1.2, it is no  
longer required to manually search and store every satellite  
position. Just pointing to a known satellite position is enough.  
This position will act as the central point. The USALS will  
then calculate positions of visible satellites.  
To use the USALS, select the  
Installation > USALS Setting  
menu. You should see a screen  
like the left figure.  
At first you have to set the Mo-  
torized DiSEqC 1.3 option to  
Enable.  
To calculate every satellite position, perform the following  
steps:  
1. Choose your desired satellite at the Satellite Name op-  
tion.  
2. Input your location to the My Longitude and My Latitude  
£
£
options with the V, V+ and numeric buttons.  
¢
¡¢  
¡
   
4.1 Searching broadcasting services 29  
3. Input the position of your selected satellite to the Satel-  
lite Angle option if it is not correct.  
4. Select the Goto the position option. Then the antenna  
will turn toward your selected satellite calculating its  
position.  
5. If the receiving quality, which is displayed at the bottom  
right of the screen, is not good, then tune the antenna  
finely with the options of the Move menu. The changed  
position is automatically saved. At this time you had  
better check the receiving quality of every transponder  
and choose the best one at the Transponder (or Fre-  
quency) option. It will be helpful to your fine tuning.  
4.1.4 Searching services  
To perform service search, se-  
lect the Installation > Service  
Search menu. You should see a  
screen like the left figure.  
There are four service search methods:  
• Searching every service of a satellite.  
• Searching every service of a transponder.  
• Searching one service of a transponder.  
• Searching every service of a SMATV (Satellite Master  
Antenna Television) transponder.  
To search every service of a satellite, perform the following  
steps:  
   
30 Service Search  
1. Choose your desired satellite at the Satellite Name op-  
tion.  
2. Set the Search Mode option to Auto.  
To search every service of a transponder, perform the follow-  
ing steps:  
1. Choose your desired satellite at the Satellite Name op-  
tion.  
2. Set the Search Mode option to Manual.  
3. Choose your desired transponder at the Frequency op-  
tion or input it with the numeric buttons.  
4. Input the symbol rate of your desired transponder to the  
Symbol Rate option with the numeric buttons.  
5. Set the Polarization option to the polarization of your de-  
sired transponder.  
6. Set the Modulation option to the modulation method of  
your desired transponder. If your desired transponder  
has high definition broadcasts, you should set this op-  
tion to DVB-S2 QPSK or DVB-S2 8PSK. Then the FEC  
option and the Pilot option will become enabled. You  
also should set these options correctly.  
NOTE  
You can get transponder information from a satellite magazine  
To search one service of a transponder, perform the following  
steps:  
1. Choose your desired satellite at the Satellite Name op-  
tion.  
2. Set the Search Mode option to Advanced.  
 
4.1 Searching broadcasting services 31  
3. Choose your desired transponder at the Frequency op-  
tion or input it with the numeric buttons.  
4. Input the symbol rate of your desired transponder to the  
Symbol Rate option with the numeric buttons.  
5. Set the Polarization option to the polarization of your de-  
sired transponder.  
6. Specify the PIDs of your desired service at the PID menu  
with the numeric buttons. PID (Packet Identifier) is a set  
of numbers that identifies transport stream packets.  
To search every service of a SMATV transponder, if the digi-  
tal receiver is connected to a SMATV, perform the following  
steps:  
1. Choose your desired satellite at the Satellite Name op-  
tion.  
2. Set the Search Mode option to SMATV.  
3. Choose your desired transponder at the Frequency op-  
tion or input it with the numeric buttons.  
4. Input the symbol rate of your desired transponder to the  
Symbol Rate option with the numeric buttons.  
5. Set the Polarization option to the polarization of your de-  
sired transponder.  
You can search pay services as well as free services. To search  
only free services. set the FTA/Scrambled option to FTA only.  
FTA means free service. To search only pay services, set it to  
CAS only. CAS means pay service. To search both free services  
and pay services, set it to FTA + CAS.  
To start service search, select the Start Search item; then a list  
box appears, in which found services will be listed. When it  
£
has completed, press the OK button to save found services.  
¢
¡
£
To stop at any time, or to exit without saving, press the EXIT  
¢
¡
button.  
 
32 Service Search  
4.2 Editing the transponder list  
You can add, delete or mod-  
ify satellite or transponder in-  
formation. Select the Installa-  
tion > SAT/TP Edit menu. You  
should see a screen like the left  
figure.  
To add a satellite entry, select the Add Satellite option. Then  
the on-screen keyboard appears. Enter your desired name and  
save it. See § 6.3 for how to use the on-screen keyboard.  
To change a satellite entry’s name, select your desired entry at  
the Satellite Name option and select the SAT Name Edit op-  
tion. Then the on-screen keyboard appears. Change the name  
as you desire and save it.  
To delete a satellite entry, select your desired entry at the Satel-  
lite Name option and select the Delete Satellite option; then  
you are asked for confirmation. If you select Yes, it will be  
deleted.  
To add a transponder entry, select your desired entry at the  
Satellite Name option and select the Add new TP option. Then  
a transponder information box appears. Input a frequency  
and its symbol rate with the numeric buttons, and specify its  
polarization.  
To delete a transponder entry, select your desired entry at the  
Frequency option and select the Delete TP option; then you  
are asked for confirmation. If you select Yes, it will be deleted.  
   
4.3 Resetting to factory settings 33  
4.3 Resetting to factory settings  
The digital receiver maintains the following data:  
• Satellite list  
• Services list  
• Favourite list  
• Timer list  
• Preference settings  
You can reset all data of the digital receiver. If you want to re-  
set all the data, select the Installation > Factory Setting menu,  
then you will be asked for confirmation. If you select Yes,  
service entries, favourite entries and timer events will all be  
deleted, and preference options will be reset to the manufac-  
turer’s factory settings.  
4.4 Resetting to installer settings  
You can store your own data including the following:  
• Satellite list  
• Services list  
• Favourite list  
• Preference settings  
Also you can restore them at any time.  
To store your data, select the Installation > System Recovery  
menu and select the Store option; then the digital receiver will  
ask your personal identification number. The number may be  
different from yours because this function is usually permitted  
only to installers. If you have entered a right number, you  
will be asekd for confirmation. If you select Yes, your data  
will be stored. Whenever you store your data, they are all  
overwritten. Refer personal identification number to § 3.4.  
To restore your data, select the Installation > System Recovery  
menu and select the Recover option; then you will be asekd  
     
34 Service Search  
for confirmation. If you replay with yes, your data will be  
restored.  
35  
Chapter 5  
Daily Usage  
5.1 Volume control  
£
£
Use the Vand V+ buttons to alter the volume to a com-  
fortable level. You may need to adjust the volume on your  
television set too. To temporarily switch off the sound, press  
the  
¢
¡
¢
¡
button. Press it again to restore the sound to previous  
level.  
5.2 Watching television  
£
£
To change services, press the P+ or Pbutton. Pressing the  
¢
¡
¢
¡
button switches to the previously viewed service. You  
can switch to your desired service by entering its service num-  
ber with the numeric buttons. You can also select a service to  
watch in the services list.  
5.2.1 The services list  
£
To view the services list, press the OK button.  
¢
¡
         
36 Daily Usage  
On the services list, you can see  
the service information:  
• Service number and name  
• Transmitting satellite  
• Transponder information  
A dollar sign ($) may be marked on some entries, indicating  
pay service. To watch pay services, you need the subscription  
card.  
To select a desired service, put the highlight bar on its entry  
£
£
£
with the P+ or Pbutton and press the OK button; then it  
¢
¡
¢
¡
¢
¡
will be presented.  
£
£
Pressing the Vor V+ button skips over 10 entries up or  
¢
¢
¡
¢
¡
down. Entering a service number with the numeric buttons  
puts the highlight bar on its entry.  
£
Pressing the F3 button performs an alphabetic browse. For  
instance, when the highlight bar is on an entry of which initial  
is B, pressing the F3 button puts the highlight bar on the first  
¡
£
¢
¡
entry of which initial is C.  
£
To sort the services list by service name, press the F2 but-  
ton. Pressing this button once more makes it sorted by service  
¢
¡
number.  
£
Pressing the F4 button displays the additional options, with  
¢
¡
which you can do the following:  
• Select your desired satellite at the Satellite option, then  
only services provided by the selected satellite will be  
listed.  
• By setting the Show Provider option to On, you can view  
the provider of the services, which is usually the name  
 
5.2 Watching television 37  
of the television company responsible for broadcasting  
them.  
To change the name of the highlighted service, select the  
Rename option; then the on-screen keyboard appears,  
with which you can enter a new name. See § 6.3 for how  
to use the on-screen keyboard.  
You can prevent other family members from watching  
the highlighted service by setting the Lock option to  
Locked. You have to enter your personal identification  
number to watch or unlock it.  
To delete the highlighted service, select the Delete op-  
tion; then you are asked for confirmation. If you select  
Yes, it will be deleted. If you want to restore it as before,  
you have to perform service search again. See § 4.1.4 for  
service search.  
To add the highlighted service into a favourite group, se-  
lect the Add to Fav option; then the favourite groups will  
be displayed. Put the highlight bar on a desired group  
£
and press the OK button.  
¢
¡
You can additionally sort the services list with the Sort-  
ing option as follows:  
Default by service number  
Alphabetic by service name  
Satellite by satellite  
FTA–CAS from free services to pay services  
CAS–FTA from pay services to free services  
Provider by service provider  
Fav–NoFav from favourite services to unfavourite  
services.  
£
Pressing the SAT button displays the satellite list. Once you  
select a desired satellite in the satellite list, only services pro-  
vided by the selected satellite are listed.  
¢
¡
 
38 Daily Usage  
You can switch between the television services list and the ra-  
dio services list by pressing the button.  
5.2.2 The favourite services list  
You can select a service to watch on a favourite list as well as  
on the services list.  
To display the favourite lists,  
£
press the FAV button; it will be  
¢
¡
displayed. As you move the  
highlight bar up or down on the  
favourite group list, favourite  
services belonging to the high-  
lighted group are listed.  
For how to edit the favourite  
lists, refer to § 6.2.  
To select a favourite service, put the hightlight bar on a desired  
£
group and press the V+ button; a highlight bar appears on the  
¢
¡
favourite services list. Once you select a desired service with  
£
the OK button, it will be presented. Otherwise, to select other  
¢
¡
£
group, press the Vbutton.  
¢
¡
After you have selected a favourite service, if you then switch  
£
£
to another service using the P+ or Pbutton, it will be also  
¢
¡
¢
¡
another favourite service of the selected group. The digital re-  
ceiver will remind you what group you have selected by dis-  
playing its name at the top right of the screen whenever you  
switch services. If you wish to get out of the current group,  
select the All services group on the favourite list.  
Besides that, you can add or delete a favourite group or ser-  
vice.  
To add a service you are watching currently in a  
favourite group, put the highlight bar of the group list on a de-  
£
sired group and press the F3 button. To create a new group,  
¢
¡
£
press the F2 button. To delete a group or a service, press the  
¢
¡
£
F4 button.  
¢
¡
 
5.2 Watching television 39  
5.2.3 Viewing programme information  
Pressing button displays the information box, on which  
you can see all of the following:  
• Service number and name  
• Transmitting satellite  
• Transponder information  
• Signal level and quality  
• Programme name  
• Programme classification symbol  
• Programme summary  
• Broadcasting time  
• Current time  
In addition, you might see the following symbols:  
• Subtitle symbol ( ) if subtitle tracks are provided on the  
current programme.  
Teletext symbol ( ) if teletext pages are provided on the  
current service.  
• Lock symbol ( ) if the current service is locked.  
• Dollar symbol ($) if the current service is a pay service.  
• Multifeed symbol ( ) if the current programme is pro-  
vided in a multifeed service. To use this feature, refer to  
§ 5.4.  
If the electronic programme guide is provided on the cur-  
rent service, you can see the information about the next pro-  
£
£
grammes with the Vor V+ button. To adjust the sound vol-  
¢
¡
¢
¡
£
£
ume in this case, press the Vor V+ button continuously un-  
¢
¡
¢
¡
til the sound bar appears and reaches your desired level.  
Pressing the  
button once more displays detailed informa-  
tion about the current programme. To hide the information  
£
box, press the EXIT button.  
¢
¡
   
40 Daily Usage  
5.2.4 Selecting audio tracks  
Some programmes are provided with audio tacks in one or  
more languages. Pressing the button displays available au-  
dio tracks. Once you select an audio track, it will be sounded.  
In addition, you can enjoy audio tracks in four sound modes:  
Stereo, Mono, Left or Right. However, if a multifeed pro-  
gramme is provided at the moment, video tracks will be dis-  
played. In this case, you have to press the  
to select an audio track.  
button once more  
5.2.5 Selecting subtitle tracks  
Some programmes are provided with subtitle tracks in one or  
more languages. If the current programme provides subtitle  
tracks, the subtitle symbol ( ) will be marked on the infor-  
mation box. Pressing the  
button displays available subtitle  
tracks. Once you select a subtitle track, it will be displayed.  
5.2.6 Viewing teletext  
On some services, such information as weather reports, news  
or stock quotations is provided by means of teletext. If the  
current service provides teletext, the teletext symbol ( ) will  
be displayed on the information box. Press the  
view teletext pages.  
button to  
Select a desired page to view by entering the page number  
with the numeric buttons. You can zoom into a teletext page  
£
£
with the F3 button, and adjust its transparency with the F4  
¢
¡
¢
¡
£
button. To hide the teletext screen, press the EXIT button.  
¢
¡
5.3 Viewing electronic programme guide  
The Electronic programme Guide shows the current and  
scheduled programmes that are or will be available on each  
service with a short summary for each programme.  
         
5.3 Viewing electronic programme guide 41  
£
Pressing the GUIDE button dis-  
¢
¡
plays the electronic programme  
guide, on which you can see the  
following:  
• Scheduled programmes  
• programme summary  
• Broadcasting date  
• Broadcasting time  
To see detailed information of a desired programme, put the  
£
£
highlight bar on your choice with the P+ or Pbutton and  
¢
¡
¢
¡
press the  
button. To switch to another service, press the  
£
£
Vor V+ button. You can travel over previous days with the  
¢
£
¡
¢
¡
£
F2 button, and can travel over next days with the F3 button.  
¢
¡
¢
¡
To see the programme guide for radio broadcasts, press the  
button. To switch it back, press the  
button again.  
£
Pressing the F1 button displays the programme guide in the  
form of a spreadsheet. To switch it back, press the F1 button  
¢
¡
£
¢
¡
again.  
You can make a timer event on the electronic programme  
guide as follows:  
1. Select a service you want.  
£
2. Press the GUIDE button to display its programme guide.  
¢
¡
£
3. Select a programme you want with the OK button, then  
¢
¡
P is marked up on the entry. At the same time, a timer  
event with the selected programme will be made in the  
timer list. Refer the timer list to § 5.5.  
4. To remove the marking, press the OK button once again.  
¢
¡
42 Daily Usage  
5.4 Watching multifeed programme  
Some broadcasts such as sports channels can provide a variety  
of perspectives on a programme at the same time. We call it a  
multifeed programme. You can select and watch a perspective  
you prefer.  
If a multifeed programme is provided on the current service,  
the multifeed symbol ( ) will be marked on the information  
box. Press the  
button, then available video tracks will be  
listed. Once you select one, it will be presented. At this time,  
you have to press the  
tracks.  
button once more to select audio  
5.5 Making timer events  
You can make the digital receiver to present your desired ser-  
vice at a specific time. Even if the digital receiver is off, it will  
turn on at the specified time.  
To input a timer recording, se-  
lect the Timer Setting menu;  
then the timer list will be dis-  
played.  
To add a new timer event, press  
£
the F1 button, and a box like  
the left figure appears. Take the  
following steps:  
¢
¡
1. If you want a radio programme, set the Type option to  
Radio; otherwise, set it to TV.  
2. Set the Satellite option to the satellite which transmits  
£
the service you want. Pressing the OK button on this  
option displays a satellite list, from which you can select  
your desired satellite.  
¢
¡
     
5.5 Making timer events 43  
3. Set the Wakeup Service option to the service which pro-  
£
vides the programme you want. Pressing the OK button  
on this option displays a services list, from which you  
can select your desired service.  
¢
¡
4. There are five timer modes:  
One Time means literally ‘one time.’  
Every Day means literally ‘every day.’  
Every Weekend means ‘Saturday and Sunday every  
week.’  
Weekly means ‘one day every week.’  
Every Weekday means ‘from Monday to Friday ev-  
ery week.’  
If your favourite programme is broadcasted at week-  
ends and you wish to watch every episode of the pro-  
gramme, set the Mode option to Every Weekend.  
5. Set the Wakeup Day option to a desired date, on which  
the digital receiver will turn on. The date format is  
day/month/year-day of the week.  
Set the Wakeup Time option to a desired time, at which  
the digital receiver will turn on. The time format is  
hour:minute.  
6. Set the Duration option to a desired time, in which the  
digital receiver will turn off.  
7. To set a timer event with the above settings, select the  
OK option; otherwise, it will not be made.  
To delete a timer event, put the highlight bar on the entry you  
£
want to remove and press the F2 button; then you are asked  
for confirmation. If you select Yes, it will be deleted.  
¢
¡
 
44 Listing Services  
Chapter 6  
Listing Services  
6.1 Editing the services list  
You would have got the services list after service search. You  
can rename, move, lock or delete service entries on the ser-  
vices list.  
Select the Organizing Svc/Fav >  
Organizing Services menu. You  
should see a screen like the left  
figure.  
There are editing options on the  
left column and service entries  
on the right column.  
Once you put the highlight bar on a desired option on the left  
£
column and press the OK button, you can select a desired ser-  
¢
¡
vice to edit on the right column. To go over to the other col-  
£
umn, press the F1 button.  
¢
¡
     
6.1 Editing the services list 45  
To edit the radio services list, press  
button; then radio ser-  
vice entries will be listed on the right column. To switch back  
to the television services list, press it again.  
To change the name of a service, select the Rename and select  
a desired service; then the on-screen keyboard appears. See  
§ 6.3 for how to use the on-screen keyboard.  
Unlike analogue broadcasts, each service does not have a  
proper service number in digital broadcasts. Service numbers  
are just assigned to the services in the order that they were  
found in the service search. So you can reassign a service num-  
ber by moving a service entry. To move a service entry, select  
the Move option and select a desired service; then the selected  
service becomes darker. As you move it up or down, it gets  
£
renumbered according to the position. Press the OK button to  
fix it.  
¢
¡
You can lock some services to prevent your children from  
watching them. To lock a service, select the Lock option and  
select a desired service; then a lock symbol will be marked  
on the selected service. If anyone tries to watch a locked ser-  
vice, the person has to enter the personal identification num-  
ber that is set to the Change PIN Code option. See § 3.4 for  
£
this option. To unlock a locked service, press the OK button  
on it.  
¢
To delete a service, select the Delete option and select a de-  
£
£
sired service with the OK button, and then press the EXIT  
¢
¡
¢
¡
button; you will be asked for confirmation. If you select Yes,  
the selected service will be deleted. If you want to undo the  
deleted service, there is nothing you can do but perform a ser-  
vice search again.  
Once you select the Sort option on the left column, sorting  
options are displayed as follows:  
Default by service number  
Alphabetic by service name  
Satellite by satellite  
 
46 Listing Services  
FTA–CAS from free services to pay services  
CAS–FTA from pay services to free services  
Provider by service provider  
Fav–NoFav from favourite services to unfavourite services.  
Transponder by transponder  
6.2 Editing the favourite list  
You can make your own favourite services list. In fact, you can  
define multiple favourite services lists, each being a ‘group’ of  
chosen services.  
Select the Organizing Svc/Fav >  
Organizing Favorites menu. You  
should see a screen like the left  
figure.  
There are 3 columns:  
• Group list (left)  
• Favourite list (centre)  
• Services list (right)  
The services list contains all available services, whereas the  
favourite list contains only chosen services that have been  
added to the highlighted group. As you move the highlight  
bar up or down on the group list, favourite services belonging  
to the highlighted group are shown in the favourite list.  
You can add up to 30 groups. To add a group, select the NEW  
option in the group list; then the on-screen keyboard appears.  
See § 6.3 for how to use the on-screen keyboard.  
To rename a group, put the highlight bar on a desired group  
you wish to rename and press the F2 button; then the on-  
screen keyboard appears. See § 6.3 for how to use the on-  
screen keyboard.  
¡
   
6.2 Editing the favourite list 47  
To delete a group, put the highlight bar on a desired group you  
£
wish to delete and press the F3 button; then a confirmation  
box appears. If you select Yes, it will be deleted.  
¢
¡
You can add a favourite service to a group by performing the  
following steps:  
1. Put the highlight bar on a desired group entry in the  
£
group list and press the OK button to select it. The high-  
light bar then moves to the services list.  
¢
¡
2. To add a service to the selected group, put the highlight  
£
bar on a desired service entry and press the OK button.  
The selected service entry is added to the favourite list.  
Repeat this step to add more entries.  
¢
¡
£
3. Press the F1 button and the highlight bar is moved to  
¢
¡
the favourite list. You can delete a favourite entry with  
£
the OK button.  
¢
¡
£
4. To select another group, press the F1 button again. By  
¢
¡
£
pressing the F1 button, the highlight bar is moved to  
¢
¡
each column.  
To add radio services, press the  
button; then radio service  
entries will be listed in the services list. To recall the television  
services list after adding radio services, press the  
again.  
button  
With your favourite services list, you can select your favourite  
services more easily. Refer to § 5.2.2 for more information.  
48 Listing Services  
6.3 How to use on-screen keyboard  
You can move the highlight key  
£
horizontally with the Vand  
¢
¡
£
V+ buttons and vertically with  
¢
¡
£
£
the P+ and Pbuttons. Press-  
¢
¡
¢
¡
£
ing the OK button on a key en-  
¢
¡
ters its letter in the input line.  
To type a space, select the Space  
key. To type lower case letters or  
numerals, select the Other key.  
To delete a letter, put the cursor on a desired letter at the input  
line and then select the Del key. You must select the Save key  
£
to complete naming; otherwise, if you press the EXIT button,  
it will not be named.  
¢
¡
6.4 Transferring receiver data  
The digital receiver retains such data as follows:  
• Services list  
• Favourite lists  
• Preference settings  
It is possible to transfer receiver data to your digital receiver  
from another same digital by receiver connecting them with a  
RS-232 cable.  
To transfer receiver data, perform the following steps:  
     
6.4 Transferring receiver data 49  
1. Plug one end of a RS-232 cable (9 pin D-  
sub cable) into the RS-232 port on the  
digital receiver, and the other end into  
the matching port on the other digital re-  
ceiver.  
2. turn on the source digital receiver.  
3. Select the Installation > Transfer Firmware  
> Transfer Data to Other IRD menu.  
4. To start the data transfer, turn on the tar-  
get digital receiver.  
NOTE  
You had better memorize some important data such as video  
settings before starting transfer to avoid loosing them.  
 
50 Firmware Update  
Chapter 7  
Firmware Update  
The digital receiver has a stable and convenient firmware to  
use. However, a new firmware may be released to improve the  
digital receiver. You can get the latest firmware and an update  
utility from the web site, http://www.i-topfield.com.  
You have to check the firmware  
information of your digital re-  
ceiver before downloading a  
new firmware. Select the Infor-  
mation > IRD Status menu. You  
should see a screen like the left  
figure.  
NOTE  
You can only update with new firmware of which System ID  
is identical to yours. Otherwise you will fail in firmware up-  
date.  
   
7.1 From a USB storage 51  
7.1 From a USB storage  
If you have a USB storage, you can update the firmware from  
it. To update the firmware from your USB storage, perform  
the following steps:  
1. Download a new firmware from the Topfield web site.  
2. Copy the firmware file to your USB storage.  
3. Insert the USB storage into the USB port on the digital  
receiver.  
4. Select the Installation > USB Firmware Upgrade menu,  
then the files in the USB storage are listed.  
5. Place the highlight bar on the right firmware file and  
£
press the OK button, then a countdown will be dis-  
played on the front of the digital receiver.  
¢
¡
6. When ‘END’ message appears, restart the digital re-  
ceiver.  
NOTE  
Your USB storage must be formatted in the FAT file system. If  
not, the digital receiver cannot recognize your USB storage. In  
addition, the digital receiver can only recognize files and di-  
rectories which are named with only alphabetic, numeric and  
underscore letters. If there is a file or forlder named with other  
letters, the digital receiver cannot recognize not only it but also  
the subsequent files and folders.  
7.2 From your computer via RS-232 port  
It is possible to transfer a new firmware to the digital receiver  
from your computer by connecting them with a RS-232 cable.  
You need TFD-Down, a firmware transfer utility for this, which  
is available from the web site, http://www.i-topfield.com.  
     
52 Firmware Update  
To update the firmware with this method, perform the follow-  
ing steps:  
1. Download a new firmware applicable to  
the digital receiver from the Topfield web  
site.  
2. Turn off the digital receiver.  
3. Plug one end of a RS-232 cable (9 pin D-  
sub cable) into the RS-232 port on the  
digital receiver, and the other end into the  
matching port on your computer.  
4. Run TFD-Down.  
The instructions on how to use TFD-Down are as follows:  
1. Press the Find button to select the new  
firmware file.  
2. Press the Download button.  
3. To start the file transfer, turn on the digital  
receiver.  
4. When the file transfer is complete, the  
display panel on the digital receiver  
will count down to zero while the new  
firmware is being applied.  
5. Restart the digital receiver.  
7.3 From another digital receiver via RS-232 port  
It is possible to transfer a new firmware to the digital receiver  
from another same digital receiver by connecting them with a  
RS-232 cable.  
To update the firmware with this method, perform the follow-  
ing steps:  
   
7.3 From another digital receiver via RS-232 port 53  
1. Turn off the target digital receiver.  
2. Plug one end of a RS-232 cable (9 pin D-  
sub cable) into the RS-232 port on the  
digital receiver, and the other end into  
the matching port on the other digital re-  
ceiver.  
3. If not already on, turn on the source digi-  
tal receiver.  
4. Select the Installation > Transfer Firmware  
> Transfer Firmware to Other IRD menu.  
5. To start the file transfer, turn on the target  
digital receiver.  
6. When the file transfer is complete, the  
display panel on the digital receiver  
will count down to zero while the new  
firmware is begin applied.  
 
54 INDEX  
Index  
16:9, 17  
DiSEqC, 26  
16:9 Display Format, 18  
22 kHz, 26  
DiSEqC 1.0, 26  
DiSEqC 1.1, 26  
4:3, 17  
DiSEqC Command Mode, 27  
Dolby Digital, 19  
Download, 52  
Duration, 43  
DVB, 1  
A/V Output Setting, 16  
Access Control, 23  
Add new TP, 32  
Add Satellite, 32  
Add to Fav, 37  
Advanced, 30  
DVB-S2 8PSK, 30  
DVB-S2 QPSK, 30  
AUDIO L, 13  
Electronic programme Guide, 40  
Audio Language, 16  
AUDIO R, 13  
Auto, 30  
Factory Setting, 33  
FEC, 30  
Find, 52  
Button, 4  
Frequency, 27, 2932  
FTA, 31  
C band, 24  
CAM, 5  
FTA + CAS, 31  
FTA only, 31  
CAS, 31  
FTA/Scrambled, 31  
CAS only, 31  
Censorship, 22  
Center extract, 18  
Change PIN Code, 22  
CI, 5  
GMT, 20  
GMT Collection, 20  
Goto, 27  
Goto the position, 29  
Common Interface, 6  
HDMI, 11, 18  
Daylight Saving Time, 21  
Delete, 37, 45  
high definition, 18  
Delete Satellite, 32  
Delete TP, 32  
Info Box Display Time, 23  
Info Box Position, 23  
 
55  
information box, 39  
Pilot, 30  
IRD Status, 50  
PIN, 22  
Polarization, 30, 31  
Ku band, 25  
keyboard, 48  
Radio, 42  
radio services list, 45  
Recover, 33  
Rename, 37, 45  
RS-232, 49, 52, 53  
Language Setting, 15  
Letter Box, 18  
LNB, 25  
LNB Frequency, 25, 26  
LNB IN, 11  
S/PDIF, 19  
LNB OUT, 11  
S/PIDF, 13  
LNB Power, 26  
LNB Setting, 25  
Local Time, 20  
Lock, 37, 45  
SAT Name Edit, 32  
SAT/TP Edit, 32  
Satellite, 20, 36, 42  
Satellite Angle, 29  
satellite list, 25, 37  
Satellite Name, 2528, 3032  
SCART, 18  
SCART Output, 16  
Search Mode, 30, 31  
Service Search, 29  
services list, 35  
Show Provider, 36  
SMATV, 29  
Manual, 30  
Menu Language, 15  
Mini A, 26  
Mode, 20, 43  
Modulation, 30  
mono, 19  
Motor Control, 27, 28  
Motorized DiSEqC 1.2, 27  
Motorized DiSEqC 1.3, 28  
Move, 29, 45  
SMATV, 31  
Sort, 45  
Movement, 27  
Sorting, 37  
multifeed, 42  
My Latitude, 28  
My Longitude, 28  
Sound Mode, 19  
Space, 48  
specifications, 8, 10  
Start Search, 31  
stereo, 19  
NEW, 46  
No block, 22  
Store, 28, 33  
normal-screen television, 17  
subtitle, 40  
Subtitle Language, 16  
Symbol Rate, 30, 31  
System ID, 50  
System Recovery, 33  
System Setting, 23  
on-screen keyboard, 46  
Organizing Favorites, 46  
Organizing Services, 44  
OSD Transparency, 23  
Other, 25  
teletext, 40  
Parental Control, 22  
PID, 31  
PID, 31  
television services list, 45  
TFD-Down, 51, 52  
time format, 20  
56 INDEX  
Time Offset, 20  
Time Setting, 20, 23  
timer list, 42  
Timer Setting, 42  
Total block, 22  
Transfer Data to Other IRD, 49  
Transfer Firmware to Other IRD, 53  
Transponder, 20, 27, 29  
transponder, 1  
TV, 12, 18, 19, 42  
TV Aspect Ratio, 17  
Type, 42  
USALS, 28  
USALS Setting, 28  
USB, 51  
USB Firmware Upgrade, 51  
User, 27  
VCR, 14  
VCR Scart Type, 17  
VIDEO, 11, 13, 19  
Video Format, 18  
Wakeup Day, 43  
Wakeup Service, 43  
Wakeup Time, 43  
wide-screen television, 17  
YPbPr, 18  
Correct disposal of this product  
This marking shown on the product or its literature indicates that it should  
not be disposed with other household wastes at the end of its working life.  
To prevent possible harm to the environment or human health from uncon-  
trolled waste disposal, please separate this from other types of wastes and  
recycle it responsibly to promote the sustainable reuse of material resources.  
Household users should contact either the retailer where they purchased  
this product or their local government office for details of where and how  
they can dispose this product for environmentally safe recycling.  
Business users should contact their supplier and check the terms and condi-  
tions of the purchase contract. This product should not be mixed with other  
commercial wastes for disposal.  
Topfield continues to improve the digital receiver which this guide explains. So some ex-  
planations and illustrations in this guide could be different from the actual digital receiver.  
Copyright © 2007, Topfield Co., Ltd.  
English version  
110T-73126-201-1 Rev. 1  

Whynter Beverage Dispenser WC 2128D User Manual
Victory Refrigeration VDW 95 38 User Manual
Traxxas Satellite Radio 1506 User Manual
Sony WALKMAN WM FX453 User Manual
Sony SCD CE775 User Manual
Sony DCR TRV60E User Manual
Sony Cyber shot DSC H50 User Manual
Sony Car Stereo System MEX BT4000P User Manual
Samsung SCL710 User Manual
Samsung Camcorder SCB 2000PH User Manual