TP209/244/409/424/430;
HT409/424; BTW09/24
English
P/N 41491
Price $5.00
Rev. B • V1 • 6/99
Middleby Cooking Systems Group • 1400 Toastmaster Drive • Elgin, IL 60120 • (847)741-3300 • FAX (847)741-4406
Solid State Slot Toaster
Models TP209, TP224, TP409, TP424, TP430,
HT409, HT424, BTW09, BTW24
OWNER'S OPERATING AND
INSTALLATION MANUAL
© 1999 Toastmaster, A Middleby Company.
is a registered trademark of Toastmaster, A Middleby Company. All rights reserved.
CAUTION
WARNING: IN CASE OF FIRE
Using any parts other than genuine Toastmaster factory
parts relieves the manufacturer of all liability.
Disconnect the toaster from its power source IMMEDI-
ATELY. This allows the unit to cool, making it easier to
put out the fire.
IMPORTANT
Contact your authorized service agent to perform mainte-
nance and repairs. A service agency directory is supplied
with your toaster.
WARNING
FORYOURSAFETYDONOTSTOREORUSEGASO-
LINEOROTHERFLAMMABLEVAPORSORLIQUIDS
IN THE VICINITY OF THIS OR ANY OTHER APPLI-
ANCE
IMPORTANT
Toastmaster (manufacturer) reserves the right to change
specifications and product design without notice. Such
revisionsdonotentitlethebuyertocorrespondingchanges,
improvements, additions or replacements for previously
purchased equipment.
WARNING
IMPROPER INSTALLATION, ADJUSTMENT, ALTER-
ATION, SERVICE OR MAINTENANCE CAN CAUSE
PROPERTY DAMAGE, INJURY OR DEATH. READ
THE INSTALLATION AND OPERATING INSTRUC-
TIONS THOROUGHLY BEFORE INSTALLING OR
SERVICING THIS EQUIPMENT.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
This manual provides detailed information for the installa-
tion and operation of your toaster. It also contains informa-
tion to assist the operator in diagnosing problems in the
event of a malfunction. This manual is an important tool for
the operator and should be kept readily available.
WARNING
DO NOT PICK UP THE TOASTER BY INSERTING
FINGERS INTO THE TOASTER SLOTS AND GRASP-
INGTHEHEATINGELEMENTS. ELECTRICALSHOCK
AND DAMAGE TO THE HEATING ELEMENTS CAN
OCCUR.
WARNING
NEVER INSERT A KNIFE, FORK, OR SIMILAR OB-
JECT INTO THE TOASTING CHAMBER. ELECTRI-
CAL SHOCK AND DAMAGE TO THE HEATING ELE-
MENTS CAN OCCUR.
WARNING
DISCONNECT THE UNIT FROM ITS ELECTRICAL
POWER SUPPLY BEFORE CLEANING OR SERVIC-
ING.
1
2. Turn the color selection knob (if necessary) to set the desired
darkness. A medium color setting is achieved at the 9 o’clock
position.
III. OPERATION
A. Location and Function of Controls
This section provides a basic description of the toaster controls, their
location, and the functions they perform. The operator MUST be
familiar with the controls. See Figure 3.
NOTE
It will be necessary to determine the color setting for each different
bakery product that is to be toasted. Test a single piece at the 9
o’clock setting, and then adjust the Color Selection Knob as
necessary to find the proper setting.
Figure 3 -Toaster Controls
3. Press the Operating Lever DOWN to lower the product into the
toasting chambers.
4. Wait for the toasting cycle to complete, and the toasted product will
automatically be raised.
OR
Operating
Lever
Push the Operating Lever UP to manually raise the product at any
time during the toasting cycle.
C. Clearing Jams
WARNING
DISCONNECT THE TOASTER FROM ITS ELECTRICAL
POWER SUPPLY BEFORE ATTEMPTING TO CLEAR A
JAM.
WARNING
Color
Selection
Knob
DO NOT TOUCH HOT SURFACES ON THE TOASTER,
OR REACH INTO THE TOASTING CHAMBER, UNTIL THE
UNIT HAS COOLED THOROUGHLY.
WARNING
NEVER INSERT A KNIFE, FORK, OR SIMILAR OBJECT
INTO THE TOASTING CHAMBER. THIS CAN CAUSE AN
ELECTRICAL SHOCK OR DAMAGE THE HEATING
ELEMENTS.
1. Color Selection Knob
Adjusts the darkness of the toasted bakery product.
•
•
Turn the knob to the LEFT for lighter toasting.
Turn the knob to the RIGHT for darker toasting.
D. Cleaning
2. Operating Lever
WARNING
•
Press the lever DOWN to load the bakery product into the
DISCONNECT THE TOASTER FROM ITS ELECTRICAL
POWER SUPPLY BEFORE CLEANING OR SERVICING.
toaster.
•
Push the lever UP to manually raise the product during the
toasting cycle. If the operating lever is not raised manually, it
will be automatically raised at the end of the toasting cycle.
WARNING
DO NOT TOUCH HOT SURFACES ON THE TOASTER,
OR REACH INTO THE TOASTING CHAMBER, UNTIL THE
UNIT HAS COOLED THOROUGHLY.
B. Operation Procedure
CAUTION
WARNING
THE REMOVABLE CRUMB TRAY MUST BE IN PLACE BEFORE THE
TOASTER MAY BE OPERATED. If the tray is removed for cleaning,
ensure that it is replaced before operation.
WHEN CLEANING THE TOASTER, NEVER APPLY
ENOUGH LIQUID TO STAND IN PLACE ON THE UNIT.
DO NOT SPRAY, RINSE, OR SUBMERGE THE TOASTER.
EXCESSIVE MOISTURE IN THE UNIT WILL CAUSE A
SEVERE ELECTRICAL HAZARD AND MAY OTHERWISE
DAMAGE THE TOASTER.
1. Insert the bakery product into the slots. For extra-wide, one-sided
slots, check that the side of the product that is to be toasted faces
the LEFT side of the slot, as shown in Figure 4.
CAUTION
DO NOT clean your toaster using abrasive cleaners or pads. Both will
scratch and dull the finish.
Figure 4 - Loading extra-wide, one-sided slots
Models HT409/424, BTW09/24 only
1. Wipe the exterior of the toaster with a sponge or cloth soaked in hot
or warm detergent water. Wipe with a clean, damp cloth to remove
the excess detergent, and then wipe again to dry the toaster.
Side of bakery
product to be
toasted faces
2. Remove the crumb tray, and empty it. Wash the crumb tray in
warm detergent water, and rinse it.
LEFT
3. After the crumb tray is dry, replace it in the toaster.
3
Model TP209
Wiring Diagram - Terminal Board
ELEMENTS
SWITCH
SOLENOID
TIMER
NOTE: All other wiring connections match
the TP224 wiring diagram at the bottom of
this page.
Electrical Specifications
•
•
120V, 50/60 Hz, 1 Ph, 1.1kW, 9.0A
Plug type: NEMA 5-15P
Model TP224
Wiring Diagram
Schematic
TIMER
ELEMENTS
SOLENOID
SWITCH
SOLENOID
TIMER
MICROSWITCH
ELEMENTS
TERMINAL
BOARD
Electrical Specifications
•
•
•
208V, 50/60 Hz, 1 Ph, 1.0kW, 4.8A OR
240V, 50/60 Hz, 1 Ph, 1.3kW, 5.3A
Plug type: NEMA 6-15P
4
Model TP409
Wiring Diagram - Terminal Board
Schematic
ELEMENTS
SWITCH
SOLENOID
TIMER
ELEMENTS
TIMER
SWITCH
SOLENOID
NOTE: All other wiring connections match
the TP424/430 wiring diagram at the bottom
of this page.
Electrical Specifications
•
•
120V, 50/60 Hz, 1 Ph, 2.2kW, 18.3A
Plug type: NEMA 5-20P (USA) OR NEMA 5-30P
(Canada)
Models TP424 & TP430
Schematic
Wiring Diagram
TIMER
TIMER
ELEMENTS
SOLENOID
SOLENOID
SWITCH
SOLENOID
MICROSWITCH
MICROSWITCH
TIMER
ELEMENTS
ELEMENTS
SOLENOID
SWITCH
TIMER
Electrical Specifications
Model TP424:
•
•
•
208V, 50/60 Hz, 1 Ph, 2.0kW, 9.6A OR
240V, 50/60 Hz, 1 Ph, 2.6kW, 10.8A
Plug type: NEMA 6-15P
TERMINAL BOARD
Model TP430:
•
208V (Canada), 50/60 Hz, 1 Ph, 2.6kW, 12.5A
•
Plug type: NEMA 6-20P
5
Model HT409
Wiring Diagram - Terminal Board
Schematic
ELEMENTS
SWITCH
SOLENOID
TIMER
ELEMENTS
TIMER
SWITCH
SOLENOID
NOTE: All other wiring connections match
the HT424 wiring diagram at the bottom of
this page.
Electrical Specifications
•
•
120V, 50/60 Hz, 1 Ph, 2.0kW, 16.6A
Plug type: NEMA 5-20P
Model HT424
Schematic
Wiring Diagram
TIMER
TIMER
ELEMENTS
SOLENOID
SOLENOID
SWITCH
SOLENOID
MICROSWITCH
MICROSWITCH
TIMER
ELEMENTS
ELEMENTS
SOLENOID
TIMER
SWITCH
Electrical Specifications
•
•
•
208V, 50/60 Hz, 1 Ph, 1.7kW, 8.0A OR
240V, 50/60 Hz, 1 Ph, 2.2kW, 9.2A
Plug type: NEMA 6-15P
TERMINAL BOARD
6
Model BTW09
Wiring Diagram - Terminal Board
Schematic
ELEMENTS
SWITCH
SOLENOID
TIMER
ELEMENTS
TIMER
SWITCH
SOLENOID
NOTE: All other wiring connections match
the BTW24 wiring diagram at the bottom of
this page.
Electrical Specifications
•
•
120V, 50/60 Hz, 1 Ph, 1.8kW,15.0A
Plug type: NEMA 5-20P
Model BTW24
Schematic
Wiring Diagram
TIMER
TIMER
ELEMENTS
SOLENOID
SOLENOID
SWITCH
SOLENOID
MICROSWITCH
MICROSWITCH
TIMER
ELEMENTS
ELEMENTS
SOLENOID
TIMER
SWITCH
Electrical Specifications
•
•
•
208V, 50/60 Hz, 1 Ph, 1.6kW, 7.7A OR
240V, 50/60 Hz, 1 Ph, 1.8kW, 7.5A
Plug type: NEMA 6-15P
TERMINAL BOARD
7
A Middleby Company
Toastmaster • 1400 Toastmaster Drive • Elgin, IL 60120 • USA • (847)741-3300 • FAX (847)741-4406
Middleby Corp 24-Hour Service Hotline 1-800-238-8444
8
|