ET1000
U S E R G U I D E
EZTALKER by Tekkeon is a sleek cord-free headset that enables
comfortable handsfree communication with your mobile phone. EZTALKER
1000 works with your Bluetooth-ready mobile phone to provide clear,
high-quality communication.
Charging EZTALKER
Before using ezTalker, you must charge the headset for approximately
two hours. When fully charged, the battery provides up to four hours of
talk time and up to 168 hours of standby time.
While using your EZTALKER headset, you can store your mobile phone in
your pocket, backpack, or briefcasejust about anywhere in close
proximity that is convenient for you.
To Charge the Headset
1. Insert ezTalker into the charging cradle as
shown.
2. Plug the charger into the charging jack on
the right side of the charging cradle.
Unpacking EZTALKER
Your ezTalker package includes
the following:
3. Plug the charger into a wall outlet. While the
headset is charging, the amber LED on the
headset will remain on. When the headset is
fully charged, the amber LED will turn off.
Figure 1.
ezTalker inserted into
charging cradle
!
ezTalker Headset
!
"Charging cradle with belt clip
ꢀCharger
"
4. Unplug the charger cable from the wall outlet and the charging
cradle.
%ezEarhook
ꢀ
%
ꢁezFit Ring
BATTERY INDICATION: When the battery is low (less than 10% of
capacity), the amber LED will flash and you’ll hear a double beep every
32 seconds.
'Comfort Pad
(User guide (not shown)
ꢁ
'
Getting to Know EZTALKER
Pairing EZTALKER to Your Mobile Phone
Pairing is the process of linking the headset with your Bluetooth mobile
phone. Before using ezTalker with your mobile phone you must pair the
devices. After this process is complete, you can use the headset only
with its paired mobile phone. To use ezTalker with a different mobile
phone, you must repeat the pairing process with the new mobile phone.
In this case, the headset will no longer work with the original mobile
phone.
TALK Button
Used for turning headset on/off,
pairing, and making/receiving calls
Amber and Blue LEDs
Provides visual indication of headset
status: power on/off, pairing mode,
muting mode, charging mode, and low
battery
BEFORE YOU PAIR THE HEADSET, ENSURE THAT THE BATTERY IS FULLY CHARGED, AND
REVIEW THE INSTRUCTIONS IN YOUR MOBILE PHONE USER GUIDE FOR PAIRING YOUR
MOBILE PHONE TO A BLUETOOTH HEADSET.
Volume Control
Used to adjust the speaker volume
and to mute the microphone
To Pair the Devices
1. Turn on the mobile phone and place it within 10 feet of the headset.
Microphone
Speaker
2. Initiate the Bluetooth device-pairing (discovery) feature on the
mobile phone. Refer to the mobile phone user guide for
instructions on initiating this feature.
3. With the headset turned off, press and hold the TALK button
approximately five seconds, until the blue and amber LEDs flash
alternately or until you hear the PAIRING tone.
4. Release the TALK button. The headset is now in Pairing Mode.
Getting Started
Before using ezTalker, you must:
5. Follow the mobile phone prompts, and when prompted for the
passkey (also called passcode or BT PIN), enter 0000 (the ezTalker
passkey). When pairing is complete, the headset will be placed in
Standby Mode, ready to make and receive calls, the amber LED
will turn off, and the blue LED will flash at two-second intervals.
ꢂ
ꢂ
ꢂ
ꢂ
Charge ezTalker
Pair ezTalker to your mobile phone
Fit ezTalker to your ear
Power ezTalker
Directions for each of these activities are provided in the following four
sections. Once these steps are completed, you will be ready to use
ezTalker!
1
U S E R G U I D E
Transferring Calls
Visual And Audible Indicators
You can transfer calls from your mobile phone to your headset.
Two LEDs (blue and amber) indicate the status of the headset, while
tones heard through the headset provide an audible indication of a
requested action. Following are descriptions of visual and audible
indicators provided by your ezTalker headset.
To Transfer Calls from Your Mobile Phone To The Headset
1. With the call connected to your mobile phone, press the TALK button
on your headset.
Visual Indicators
LED Status
Indicates
Adjusting the Volume
Blue LED flashes at two-
second intervals
Blue and amber LEDs flash
alternately
Headset is in standby mode,
ready to make and receive calls
Headset is in Pairing Mode
To Increase the Volume
1. Press and release the top of the VOLUME
Amber LED flashes
Both LEDs are off
Battery is low
Headset is off
Figure 5.
Volume buttons
button + to increase the volume one level.
Repeat until you have reached the desired
Audible Indicators
Tone
Series of tones, increasing in Headset has been turned on.
pitch
Series of tones, decreasing
in pitch
One long beep and one short Battery is low
beep every 32 seconds
Double chime
level.
Indicates
To Decrease the Volume
1. Press and release the bottom of the VOLUME button - to decrease
the volume one level. Repeat until you have reached the desired
level.
Headset is about to turn off.
Headset has been put into
Muting EZTALKER
You can mute and un-mute the microphone temporarily so that you
cannot be heard by the connected party.
Pairing Mode.
Beeps every four seconds
Headset is muted.
To Mute the Headset
Troubleshooting
If your headset is not communicating with your mobile phone, ensure
that the headset is on and charged, and that you have paired the
headset with your mobile phone.
1. Press and hold either VOLUME button (+/-) for three seconds. While
the headset is muted, you will hear a beep every four seconds.
To Un-Mute the Headset
1. When the microphone is muted, press and hold either VOLUME
button (+/-) for three seconds.
If you encounter poor reception via the headset, verify that you have
good reception on your mobile phone or move closer to your mobile
phone. If the reception is still poor, try moving the mobile phone away
from your body, or to the same side of your body as your headset.
Storing EZTALKER
When you’re not using ezTalker, you can store it in the charging cradle.
If you are in a noisy environment and your mobile phone does not
accept voice commands, dial the number from the mobile phone keypad
as the loud background noise may interfere with voice commands.
3
U S E R G U I D E
FCC Statement for Class B Digital Devices
Limited Warranty
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try and correct the interference by one or more of the following
measures:
The product enclosed herein is warranted to be free of operational defects for a
period of one year from the date of purchase. In the event of a defect in operation
during the warranty period Tekkeon, Inc. will replace the defective product when
the owner returns all product contents. The limited warranty will be considered
void if the unit is tampered with, subject to misuse, negligence or accidental
damage, has been improperly serviced, or if the security seal is removed. This
warranty is limited to replacement only and shall not cover any other damages. Any
product returned to Tekkeon, Inc. with no fault found will be returned to the owner
at the owner’s expense.
To obtain warranty coverage, please complete and submit the enclosed EzTalker
registration card.
ꢂ
ꢂ
ꢂ
Reorient or locate the receiving antenna.
Disclaimer of Warranties
Increase the separation between the equipment and receiver.
Any user of this product does so at the user’s own risk. To the maximum extent
permitted by applicable law, Tekkeon, Inc. and its suppliers provide the hardware
and any support services related thereto “as is” and with all faults; and hereby
disclaim all warranties and conditions, whether express, implied or statutory,
including, but not limited to implied warranties of merchantability, fitness for a
particular purpose, non-infringement, lack of negligence or correspondence to
description, except for those warranties specifically and expressly provided in the
Limited Warranty.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
ꢂ
Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
With respect to the use of this product, in no event shall the company be liable for
any loss of profit or any other commercial damage, including but not limited to
special, incidental, consequential and other damages.
"Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device."
Customer Service Information
Customer service for EzTalker is available at:
Tekkeon, Inc.
c/o ezTalker
3002 Dow Avenue, #218
Tustin, CA 92780
888-787-5888 / 714-832-1266
Tekkeon, Inc. must issue a Return Merchandise Authorization (RMA) number for all
exchanges or refunds.
© 2003 Tekkeon, Inc.
Revision B5
All Rights Reserved
4
|