3-214-657-11(1)
Digital HD Video Camera Recorder
Handycam Handbook
HDR-CX6EK/CX7E/
CX7EK
© 2007 Sony Corporation
• When connecting your camcorder to
another device with a cable, be sure to
insert the connector plug in the correct
way. Pushing the plug forcibly into the
terminal will damage the terminal and
may result in a malfunction of your
camcorder.
• Connect the A/V connecting cable to the
Handycam Station when using your
camcorder attached to the Handycam
Station.
• Do not aim at the sun. Doing so might
cause your camcorder to malfunction.
Take images of the sun only in low light
conditions, such as at dusk.
About changing the language setting
• The on-screen displays in each local
language are used for illustrating the
operating procedures. Change the screen
language before using your camcorder if
• Disconnect the AC Adaptor from the
Handycam Station holding both the
Handycam Station and the DC plug.
• Be sure to slide the POWER switch to
OFF (CHG) when you insert the
On recording
• Before starting to record, test the
recording function to make sure the image
and sound are recorded without any
problems.
• Compensation for the contents of
recordings cannot be provided, even if
recording or playback is not possible due
to a malfunction of the camcorder, storage
media, etc.
• TV color systems differ depending on the
country/region. To view your recordings
on a TV, you need a PAL system-based
TV.
• Television programs, films, video tapes,
and other materials may be copyrighted.
Unauthorized recording of such materials
may be contrary to the copyright laws.
camcorder into the Handycam Station or
remove the camcorder from it.
About menu items, LCD panel and
lens
• A menu item that is grayed out is not
available under the current recording or
playback conditions.
• The LCD screen is manufactured using
extremely high-precision technology, so
over 99.99% of the pixels are operational
for effective use. However, there may be
some tiny black points and/or bright
points (white, red, blue, or green in color)
that appear constantly on the LCD screen.
These points are normal results of the
manufacturing process and do not affect
the recording in any way.
On playing back recorded images on
other devices
• To view the HD (high definition) images
on the “Memory Stick PRO Duo” on other
devices, the device must comply with the
AVCHD format. Otherwise, you cannot
view the images.
Save all your recorded image data
Black point
• To prevent your image data from being
lost, save all your recorded images on
external media. It is recommended that
you save the image data on a disc such as
Also, you can save your image data using
White, red, blue or
green point
• Exposing the LCD screen or the lens to
direct sunlight for long periods of time
may cause malfunctions.
3
• It is recommended that you save your
image data periodically, after recording.
Notes on battery pack/AC Adaptor
• While the access lamp is lit, be sure to
avoid the following. They may cause
malfunctions.
– Removing the battery pack
– Removing the AC Adaptor (while operating
the camcorder on the external power source)
– Ejecting the “Memory Stick PRO Duo”
• Be sure to remove the battery pack or the
AC Adaptor after turning off the POWER
switch.
About this Handbook
• The images of the LCD screen used in this
Handbook for illustration purposes are
captured using a digital still camera, and
therefore may appear different.
• Design and specifications of recording
media and other accessories are subject to
change without notice.
About the Carl Zeiss lens
Your camcorder is equipped with a Carl
Zeiss lens, which was developed jointly by
Carl Zeiss, in Germany, and Sony
Corporation, and produces superior images.
It adopts the MTF measurement system for
video cameras and offers a quality typical
of a Carl Zeiss lens. Also, the lens for your
camcorder is T -coated to suppress
unwanted reflections and faithfully
reproduce colors.
MTF= Modulation Transfer Function. The
number value indicates the amount of light
from a subject coming into the lens.
4
Table of Contents
Read this before operating your
Playing back from a face image
Searching for desired movies by date
Playing back a series of still images
“
HOME” and “ OPTION”
menus .......................................12
Step 3: Turning the power on and
Dubbing to VCR or DVD/HDD
Printing recorded images (PictBridge
Step 4: Adjusting the camcorder to
Step 5: Inserting a “Memory Stick
category ....................................54
Formatting the “Memory Stick PRO
Recording and playback with ease
Checking the “Memory Stick PRO
Repairing the image database file
Recording sound with more presence
Recording high quality still images
....................................................... 31
Recording in dark places
What you can do with the
Adjusting the exposure for backlit
Recording the fast action in slow-
HOME MENU .......................57
List of the
(SETTINGS) category
items .............................................. 58
5
Indicators displayed during recording/
(Items to adjust the sound and the
(Items for when connecting other
Activating functions using the
Recording items on the OPTION
Viewing items on the OPTION
Functions set in the
OPTION
Warning indicators and messages
Files/folder structure on the “Memory
About the “InfoLITHIUM” battery
About handling of your camcorder
6
Subject examples and solutions
Checking your golf
swing
Getting a good
shot of a ski slope
or beach
Capturing still
images during
movie recording
A child on the
stage under a spot
light
Flowers in close-
up
Fireworks with all
its splendor
Focusing on the
dog on the left
A sleeping child
under dim light
side of the screen
7
Enjoying Your Camcorder
Operation flow
• On the “Memory Stick PRO Duo” you can use with your camcorder, see page 11.
• You can record movies and still images on a “Memory Stick PRO
Duo.”
• You can select the image quality: HD (high definition) image
quality or SD (standard definition) image quality (p. 59).
HD (high definition) image quality
AVCHD format
SD (standard definition) image
quality
MPEG2 format
Image resolution: about 3.75 times
of that of SD (standard definition)
image quality
Records with SD (standard
definition) image quality.
b Notes
“AVCHD 1080i format” is abbreviated as “AVCHD” in this manual, except when it must be
described in more detail.
8
You can enjoy movies with HD (high definition) image
quality, with the same image quality as they were recorded.
You can enjoy movies recorded with HD (high definition)
image quality, but they will be converted to SD (standard definition) image quality.
b Notes
• To view the HD (high definition) images on the “Memory Stick PRO Duo” on other devices, the
device must comply with the AVCHD format. Otherwise, you cannot view the images.
• Some AVCHD format devices may not be able to play the “Memory Stick PRO Duo.”
z Tips
and camcorder.
x Saving images on a disc using a computer
x Importing images to a computer
z Tips
• You can view movies with HD (high definition) image quality on computers, using the supplied
“Picture Motion Browser.”
• See “Picture Motion Browser Guide” on the supplied CD-ROM about handling images on a
computer.
9
BDelete images.
If the “Memory Stick PRO Duo” is full, you cannot record
new images. Delete image data that has been saved on a
computer or a disc from the “Memory Stick PRO Duo.” If
you delete images that have been saved elsewhere, you can
record new images on newly freed up space of the
“Memory Stick PRO Duo.”
Expected recording time of movies
The recording time depends on the capacity of “Memory Stick PRO Duo” and recording mode
(p. 59).
Approximate recordable time in minutes (Minimum recordable time in minutes)
“Memory Stick PRO
Duo” capacity
512MB
1GB
2GB
4GB
8GB
HD (high definition) image quality
AVC HD 15M (XP)
3* (3)
7 (7)
15 (15)
25 (20)
35 (25)
45 (35)
30 (30)
55 (40)
65 (45)
85 (70)
60 (60)
115 (80)
140 (100)
175 (145)
(highest quality)
AVC HD 9M (HQ)
6 (4)
10 (10)
15 (10)
20 (15)
(high quality)
AVC HD 7M (SP)
8 (6)
(standard quality)
AVC HD 5M (LP)
10 (8)
(long play)
SD (standard definition) image quality
SD 9M (HQ)
6 (5)
10 (10)
20 (10)
40 (25)
25 (25)
40 (25)
80 (55)
55 (50)
80 (50)
115 (100)
170 (100)
325 (215)
(high quality)
SD 6M (SP)
10 (5)
(standard quality)
SD 3M (LP)
15 (10)
160 (105)
(long play)
* Since the recordable time is less than 5 minutes,
appears (p. 84).
z Tips
• Figures such as 15M and 9M in the table show the average bit rate. M stands for Mbps.
10
“Memory Stick” you can use with your camcorder
• For recording movies, it is recommended that you use a “Memory Stick PRO Duo” of 512
MB or larger marked with:
–
(“Memory Stick PRO Duo”)
–
(“Memory Stick PRO-HG Duo”)
• A “Memory Stick PRO Duo” of up to 8 GB has been confirmed to operate correctly with this
camcorder.
• See the following URL on the “Memory Stick” you can use on your camcorder.
http://www.sony.net/memorystick/supporte/
• You can record movies of a maximum of 3,999 scenes with HD (high definition) image
quality, and 9,999 scenes with SD (standard definition) image quality.
Your camcorder uses the VBR (Variable Bit Rate) format to automatically adjust image quality to suit the
recording scene. This technology causes fluctuations in the recording time of the “Memory Stick PRO Duo.”
Movies containing quickly moving and complex images are recorded at a higher bit rate, and this reduces
the overall recording time.
11
Enjoying your camcorder
“ HOME” and “ OPTION”
- Taking advantage of two types of menus
“
HOME MENU” - the starting point for operations with your
camcorder
(HELP)
Displays a description of the item (p. 13)
Category
BCategories and items of the HOME MENU
(CAMERA) category
(MANAGE MEMORY STICK) category
Item
Page
Item
Page
MOVIE*
FORMAT*
PHOTO*
SMTH SLW REC
INFO
REPAIR IMG.DB F.
(VIEW IMAGES) category
(SETTINGS) category*
Item
Page
VISUAL INDEX*
INDEX*
* You can also set these items during Easy
available in the
(SETTINGS) category, see
INDEX*
PLAYLIST
(OTHERS) category
Item
Page
DELETE*
EDIT
PLAYLIST EDIT
PRINT
COMPUTER
TV CONNECT Guide*
12
Using the HOME MENU
4
5
Touch the desired item.
Example: [EDIT]
1
While pressing the green button
in the center, slide the POWER
switch in the direction of the
arrow to turn on the power.
Follow the guide on the screen for
further operation.
To hide the HOME MENU screen
Touch
.
2
3
Press
(HOME) A (or B).
BWhen you want to know something
about the function of each item on
the HOME MENU - HELP
(HOME) B
1
Press
(HOME).
The HOME MENU appears.
(HOME) A
Touch the desired category.
Example: (OTHERS) category
2
Touch
(HELP).
The bottom of the
orange.
(HELP) turns
13
3
Touch the item you want to learn
more about.
When you touch an item, its explanation
appears on the screen.
To apply the option, touch [YES],
otherwise, touch [NO].
To deactivate the HELP
Touch
(HELP) again in step 2.
Using the OPTION MENU
Just a touch on the screen during shooting
or playback displays the functions available
at that moment. You will find it easy to
further details.
(OPTION)
14
GSetttiengpSta1rte:d Checking supplied items
Make sure that you have the following
items supplied with your camcorder.
The number in the parentheses indicates the
number of that item supplied.
A button-type lithium battery is already installed.
NP-FH60
Mains lead (1) (p. 16)
21-pin adaptor (p. 44)
For the model with the
bottom surfaces only.
mark printed on their
CD-ROM “Handycam Application
Software” (1)
– Picture Motion Browser (Software)
– Picture Motion Browser Guide
– Handycam Handbook (This Handbook)
“Operating Guide” (1)
Component video cable (1) (p. 41)
HDR-CX6EK/CX7EK
“Memory Stick PRO Duo” 4 GB (1) (p. 22)
USB cable (1) (p. 52)
15
Step 2: Charging the battery pack
/CHG
(charge) lamp
POWER
switch
DC IN jack
DC plug
Mains lead
To the wall socket
AC Adaptor
Battery pack
You can charge the “InfoLITHIUM”
4
5
Attach the battery pack by sliding
it in the direction of the arrow
until it clicks.
attaching it to your camcorder.
b Notes
• You cannot attach any “InfoLITHIUM” battery
pack other than the H series to your camcorder.
Place the camcorder on the
Handycam Station as shown
above, and insert it into the
Handycam Station securely, all
the way to the bottom.
1
Connect the AC Adaptor to the
DC IN jack on the Handycam
Station.
The /CHG (charge) lamp lights up and
charging starts. When the /CHG
(charge) lamp turns off, the battery is
charged.
Be sure that the v mark on the DC plug
is facing up.
2
3
Connect the mains lead to the AC
Adaptor and the wall socket.
b Notes
• When inserting the camcorder into the
Handycam Station, close the DC IN jack cover.
Slide the POWER switch in the
direction of the arrow to OFF
(CHG) (the default setting).
16
To remove your camcorder from the
Handycam Station
Turn off the power, then remove the
camcorder from the Handycam Station
holding both your camcorder and the
Handycam Station.
To remove the battery pack
Slide the POWER switch to OFF (CHG).
Slide the BATT (battery release) lever and
remove the battery pack.
BATT (battery
release) lever
b Notes
• When you remove the battery pack or
disconnect the AC Adaptor, make sure that the
(Movie) lamp/
turned off.
(Still) lamp (p. 20) is
When storing the battery pack
Fully discharge the battery pack before
storing it for an extended period (see page
93 for the details of storage).
To charge the battery pack using only
the AC Adaptor
Turn off the power, then connect the AC
Adaptor to the DC IN jack on your
camcorder.
To use a power source from a wall
socket
POWER switch
Make the same connections as you do when
charging the battery pack. The battery pack
will not lose its charge in this case.
To check the remaining battery
(Battery Info)
DC plug
Set the POWER switch to OFF (CHG), then
press DISP/BATT INFO.
DC IN jack
Open the jack
cover
With the v mark
on the left
b Notes
• Disconnect the AC Adaptor from the DC IN
jack holding both the camcorder and the DC
plug.
After a while, the approximate recordable
time and battery information appear for
about 7 seconds. You can view the battery
17
information for up to 20 seconds by
pressing DISP/BATT INFO again while the
information is displayed.
* Typical recording time shows the time when
you repeat recording start/stop, turning the
power on/off and zooming.
Remaining battery (approx.)
b Notes
• All times are measured under following
conditions.
– Recording mode: SP
– [
INDEX]: [OFF]
– LCD backlight: [ON] (top), [OFF] (bottom)
Playing time
Recording capacity (approx.)
Approximate time (min.) available when
you use a fully charged battery pack.
“HD” stands for high definition image
quality, and “SD” stands for standard image
quality.
Charging time (full charge)
Approximate time (min.) required when
you fully charge a fully discharged battery
pack.
Battery pack
LCD panel opened*
HD SD
120 140
Battery pack
NP-FH50
Charging time
Image quality
NP-FH50
135
135
170
390
NP-FH60 (supplied)
NP-FH70
NP-FH60 (supplied)
NP-FH70
160
255
580
190
300
680
NP-FH100
NP-FH100
* When the LCD backlight is on.
Recording time
On the battery pack
• Before changing the battery pack, slide the
POWER switch to OFF (CHG) and turn off the
Approximate time (min.) available when
you use a fully charged battery pack.
“HD” stands for high definition image
quality, and “SD” stands for standard image
quality.
(Movie) lamp/
• The /CHG (charge) lamp flashes during
charging, or Battery Info (p. 17) will not be
correctly displayed under the following
conditions:
– The battery pack is not attached correctly.
– The battery pack is damaged.
– The battery pack is worn-out (For Battery
Info only).
• The power will not be supplied from the battery
as long as the AC Adaptor is connected to the
DC IN jack of your camcorder or the Handycam
Station, even when the mains lead is
Continuous
recording
time
Typical
recording
time*
Battery pack
Image quality
NP-FH50
HD SD
HD SD
70
75
80
85
35
35
45
50
75
80
40
40
55
55
90
90
NP-FH60
(supplied)
95 110
100 115
155 180
160 185
NP-FH70
disconnected from the wall socket.
• When attaching an optional video light, it is
recommended that you use an NP-FH70 or NP-
FH100 battery pack.
NP-FH100
360 405 180 200
370 415 185 205
18
• We do not recommend using an NP-FH30,
which only allows short recording and playback
times, with your camcorder.
On the charging/recording/playback time
• Times measured when using the camcorder at
25 °C (77 °F) (10 °C to 30 °C (50 °F to 86 °F) is
recommended).
• The recording and playback time will be shorter
when you use your camcorder in low
temperatures.
• The recording and playback time will be shorter
depending on the conditions under which you
use your camcorder.
On the AC Adaptor
• Use the nearby wall socket when using the AC
Adaptor. Disconnect the AC Adaptor from the
wall socket immediately if any malfunction
occurs while using your camcorder.
• Do not use the AC Adaptor placed in a narrow
space, such as between a wall and furniture.
• Do not short-circuit the DC plug of the AC
Adaptor or battery terminal with any metallic
objects. This may cause a malfunction.
• Even if your camcorder is turned off, AC power
(mains) is still supplied to it while connected to
the wall socket via the AC Adaptor.
19
Step 3: Turning the power on and setting the
date and time
Set the date and time when using this
camcorder for the first time. If you do not
3
Set [SUMMERTIME], then touch
[NEXT].
set the date and time, the [CLOCK SET]
screen appears every time you turn on your
camcorder or change the POWER switch
position.
4
Set [Y] (year) with v/V.
Lens cover
5
6
7
Select [M] with b/B, then set the
month with v/V.
Touch the button
on the LCD
screen.
Set [D] (day), hour and minute in
the same way, then touch [NEXT].
POWER switch
Make sure that the clock is
1
While pressing the green button,
slide the POWER switch
repeatedly in the direction of the
arrow until the respective lamp
lights up.
correctly set, then touch
.
The clock starts.
You can set any year up to the year
2037.
(Movie): To record movies
(Still): To record still images
The [CLOCK SET] screen appears.
To turn off the power
Slide the POWER switch to OFF (CHG).
To reset the date and time
Touch
(HOME) t
(SETTINGS)
t [CLOCK/ LANG] t [CLOCK
SET], and set the date and time.
b Notes
• If you do not use your camcorder for about 3
months, the built-in rechargeable battery gets
discharged and the date and time settings may
be cleared from the memory. In that case,
charge the built-in rechargeable battery and then
2
Select the desired geographical
area with v/V, then touch [NEXT].
20
Step 4: Adjusting the
camcorder to suit you
• It takes a few seconds for your camcorder to be
ready to shoot after the power is turned on. You
cannot operate your camcorder during this time.
Adjusting the LCD panel
• The lens cover opens automatically when the
power is turned on. It closes when the playback
screen is selected, or the power is turned off.
Open the LCD panel 90 degrees to the
camcorder (1), then rotate it to the best
angle to record or play (2).
• In the setting at the time of purchase, the power
turns off automatically if you leave your
camcorder without any operation attempted for
approximately 5 minutes, to save battery power
DISP/BATT INFO
290 degrees
(max.)
z Tips
• The date and time does not appear during
recording, but they are automatically recorded
on the “Memory Stick PRO Duo,” and can be
displayed during playback ([DATA CODE],
“World time difference.”
• If the buttons on the touch panel do not work
correctly, adjust the touch panel
190 degrees to the
camcorder
2180 degrees
(max.)
To turn off the LCD backlight to make
the battery last longer
Press and hold DISP/BATT INFO for a few
Changing the language setting
seconds until
appears.
This setting is practical when you use your
camcorder in bright conditions or you want
to save battery power. The recorded image
will not be affected by the setting. To turn
on the LCD backlight, press and hold DISP/
BATT INFO for a few seconds until
disappears.
You can change the on-screen displays to
show messages in a specified language. To
select the screen language, touch
(HOME) t
(SETTINGS) t [CLOCK/
LANG] t [
b Notes
• Do not press the buttons beside the LCD screen
accidentally when you open or adjust the LCD
panel.
z Tips
• If you open the LCD panel 90 degrees to the
camcorder, then rotate it 180 degrees to the lens
side, you can close the LCD panel with the LCD
screen facing out. This is convenient during
playback operations.
• Touch
(HOME) t
(SETTINGS) t
[SOUND/DISP SET] t [LCD BRIGHT]
screen.
• The information is displayed or hidden (display
y no display) each time you press DISP/
BATT INFO.
21
Step 5: Inserting a
“Memory Stick PRO
Duo”
Fastening the grip belt
can use with your camcorder.
Fasten the grip belt and hold your
camcorder correctly.
z Tips
• See following pages on the recordable time of
movies and recordable number of still images.
1
2
Open the LCD panel.
Slide the POWER switch
repeatedly until the
lamp lights up.
(Movie)
If the power is turned off, slide the
POWER switch while pressing the
green button.
22
To eject a “Memory Stick PRO Duo”
Open the LCD panel and Memory Stick
Duo cover, lightly push the “Memory Stick
PRO Duo” in once.
3
Insert the “Memory Stick PRO
Duo.”
1 Open the Memory Stick Duo cover in
the direction of the arrow.
b Notes
2 Insert the “Memory Stick PRO Duo”
into the Memory Stick Duo slot in the
right direction until it clicks.
• When the access lamp is lit or flashing, your
camcorder is reading/writing data. To prevent
image data from being damaged, do not:
– eject the “Memory Stick PRO Duo”
– remove the battery pack or AC Adaptor
– shake or knock your camcorder
3 Close the Memory Stick Duo cover.
• Do not open the Memory Stick Duo cover
during recording.
• If you force the “Memory Stick PRO Duo” into
the slot in the wrong direction, the “Memory
Stick PRO Duo,” the Memory Stick Duo slot, or
image data may be damaged.
• If [Failed to create a new Image Database File.
It may be possible that there is not enough free
“Memory Stick PRO Duo.” Note that formatting
will delete all data recorded on the “Memory
Stick PRO Duo.”
Access lamp
• When inserting or ejecting the “Memory Stick
PRO Duo,” be careful so that the “Memory
Stick PRO Duo” does not pop out and drop.
If you insert a new “Memory Stick PRO
Duo,” the [Create a new Image
Database File.] screen appears.
z Tips
• You can shoot still images without creating a
management file.
4
Touch [YES].
23
Recording/Playback
Recording and playback with ease
(Easy Handycam operation)
Easy Handycam operation makes nearly all settings automatic so that you can perform
recording or playback operation without detailed settings. It also makes screen font size larger
for easy viewing.
If the POWER switch is set to OFF (CHG),
turn it while pressing the green button.
Recording movies
Recording still images
1
Slide the POWER switch
I in the direction of the
arrow until the
1
Slide the POWER switch
I in the direction of the
arrow until the
lamp lights up.
(Still)
(Movie) lamp lights up.
2
3
Press EASY A.
2
3
Press EASY A.
appears on
the LCD screen.
appears on
the LCD screen.
Press START/STOP J (or F) to
start recording.*
Press PHOTO H lightly to adjust
the focus
press it fully
A
(a beep sounds), then
(a shutter click
B
sounds).**
[STBY] b [REC]
Flashing b Lights up
To stop recording, press START/STOP
again.
**The setting of [
24
Playing back recorded movies/still images
1
Slide the POWER switch I to turn on your camcorder.
Press (VIEW IMAGES) B (or G).
2
The VISUAL INDEX screen appears on the LCD screen (It may take some time to display
the thumbnails).
Appears with the image on each of the tab that was lastly played back/
recorded (B for the still image)
Returns to the
recording screen
Searches for images
by date (p. 37)
Previous 6 images
Next 6 images
Returns to the
recording screen
Displays still images
Displays movies with HD (high
definition) image quality.*
*
appears for movies with SD (standard definition) image quality. To play back movies of another
image quality, touch (HOME) E (or D) t (SETTINGS) t [VIEW IMAGES SET] t
INDEX SET].
[
/
Playing back images from INDEX
Press
t [ INDEX].
(Film Roll Index) C, or touch
(HOME) E (or D) t
(VIEW IMAGES)
25
3
Start playback.
Movies:
Touch the
or
tab, and then touch the desired movie.
Toggles Play or Pause as you touch
Return (to the
VISUAL INDEX
screen)
Beginning of the
Next movie
movie/previous movie
The recording
date/time*
Stop (go to the
VISUAL INDEX
screen)
Reverse/ Forward
z Tips
• When playback from the selected movie reaches the last movie, the screen returns to the VISUAL INDEX
screen.
• You can slow down the playback speed by touching
/
during pause.
• You can adjust volume by touching
SETTINGS] t [VOLUME], then touch
(HOME) E (or D) t
(SETTINGS) t [SOUND
/
.
Still images:
Touch the
tab, and then touch the desired still image.
Return (to the
VISUAL INDEX
screen)
The recording date/
time*
Goes to the VISUAL
INDEX screen
Previous/Next
26
To cancel Easy Handycam operation
Press EASY A again.
disappears
from the LCD screen.
Menu settings during Easy Handycam
operation
Press
(HOME) E (or D) to display
the menu items available for setup changes
b Notes
• Most of the menu items automatically return to
the default settings. The settings of some menu
items are fixed. For details, see page 77.
• You cannot use the
(OPTION) menu.
• Cancel Easy Handycam operation if you want to
add effects to images or change settings.
Invalid buttons during Easy Handycam
operation
You cannot use some buttons/functions
during Easy Handycam operation since
an invalid operation, [Invalid during Easy
Handycam operation] may appear.
27
Recording
(HOME) A
Lens cover
Opens automatically
when the power is
switched on.
PHOTO E
(HOME) D
START/STOP B
Access lamp
(Movie) lamp
(Still) lamp
/CHG (charge) lamp
START/
STOP F
POWER switch C
If the POWER switch is set to OFF (CHG), turn it while pressing
the green button.
b Notes
“Memory Stick” you can use with your
• When a movie file exceeds 2 GB, the next
movie file is created automatically.
camcorder
• For recording movies, it is recommended
that you use a “Memory Stick PRO Duo”
of 512 MB or larger marked with:
z
Tips
• You can check the free space of the “Memory
Stick PRO Duo” by touching (HOME) A
(MANAGE MEMORY
–
(“Memory Stick
PRO Duo”)
(or D) t
STICK) t [
–
(“Memory Stick
PRO-HG Duo”)
• A “Memory Stick PRO Duo” of up to 8
GB has been confirmed to operate
correctly with this camcorder.
• See the following URL on the “Memory
Stick” you can use on your camcorder.
http://www.sony.net/memorystick/
supporte/
28
Recording movies
Recording still images
For the recordable number of still images,
1
2
Slide the POWER switch C in the
direction of the arrow to light up
1
2
Slide the POWER switch C until
the (Still) lamp lights up.
the
(Movie) lamp.
Press PHOTO E lightly to adjust
the focus A (a beep sounds),
then press it fully B (a shutter
click sounds).
Press START/STOP B (or F).
[STBY] t [REC]
To stop recording, press START/STOP
B (or F) again.
Flashing bLights up
appears beside
. When
disappears, the image has been
recorded.
z Tips
• Movies are recorded in the HD (high definition)
•
appears when [
INDEX SET] is set to
[ON] (the default setting) during movie
• You can switch the shooting mode by touching
(HOME) A (or D) t
t [MOVIE] or [PHOTO].
(CAMERA)
images during movie recording.
• You can copy scenes of recorded movies as still
images on the “Memory Stick PRO Duo” using
the supplied “Picture Motion Browser.” For
details, see “Picture Motion Browser Guide” on
the supplied CD-ROM.
29
Zooming
Recording sound with more
presence (5.1ch surround
recording)
You can magnify images up to 10 times the
original size with the power zoom lever or
the zoom buttons beside the LCD screen.
Dolby Digital 5.1ch surround sound can be
recorded with the internal microphone. You
can enjoy realistic sound when playing the
movieondevicesthatsupport5.1chsurround
sound.
Internal microphone
Wider range of view:
(Wide angle)
Dolby Digital 5.1 Creator, 5.1ch surround sound
Glossary (p. 105)
b Notes
• 5.1chsound isconvertedto2chwhen playedback
on your camcorder.
• To enjoy the 5.1ch surround sound recorded,
you need a device compatible with 5.1ch
surround sound.
• You can create a disc, which contains the
movies recorded on your camcorder, on a
computer using the supplied software. If you
play the disc on a 5.1ch surround system, you
can enjoy realistic sound.
Close view: (Telephoto)
Move the power zoom lever slightly for a
slower zoom. Move it further for a faster
zoom.
b Notes
• Be sure to keep your finger on the power zoom
lever. If you move your finger off the power
zoom lever, the operation sound of the power
zoom lever may also be recorded.
•
is displayed on the screen during 5.1ch
recording/playback.
• You cannot change the zoom speed with the
zoom buttons beside the LCD screen.
• The minimum possible distance between
camcorder and subject while maintaining sharp
focus is about 1 cm (about 13/32 in.) for wide
angle and about 80 cm (about 2 5/8 feet) for
telephoto.
z Tips
want to zoom to a level greater than 10 × when
recording movies.
30
Using the flash
Recording high quality still
images during movie recording
(Dual Rec)
/CHG (charge) lamp
Flash
1 Slide the POWER switch until the
(Movie) lamp lights up, then press START/
STOP to start movie recording.
Press (flash) repeatedly to select an
appropriate setting.
No indication (Auto flash): Automatically
flashes when there is insufficient ambient
light.
2 Press PHOTO fully.
After you start recording, and before you
finish, you can select up to 3 frames of still
images from your movie.
r
(Forced flash): Always uses the flash
regardless of the surrounding brightness.
r
Orange color
boxes indicate the
number of
recorded images.
When recording is
finished, the color
changes to orange.
(No flash): Records without flash.
b Notes
• The recommended distance to the subject when
using the built-in flash is approximately 0.3 to
2.5 m (1 to 8 feet).
• Remove any dust from the surface of the flash
before using it. Flash effect may be impaired if
heat discoloration or dust obscures the lamp.
• The /CHG (charge) lamp flickers while
charging the flash, and remains lit when the
battery charge is complete.
• If you use the flash in bright places such as
when shooting a backlit subject, the flash may
not be effective.
3 Press START/STOP to stop movie
recording.
Stored still images appear one by one, and
the images are stored. When
disappears, the image has been recorded.
b Notes
• Do not eject the “Memory Stick PRO Duo”
before movie recording is finished and the still
images are completely stored on the “Memory
Stick PRO Duo.”
• When attaching a conversion lens (optional) or a
filter (optional) to your camcorder, the flash
does not emit light.
• You cannot use the flash during Dual Rec.
z Tips
z Tips
• When the POWER switch is set to
the size of still images becomes [
(16:9 wide) or [3.4M] (4:3).
(Movie),
4.6M]
• You can change the brightness of the flash by
prevent the redeye by setting [REDEYE
• You can record still images during recording
standby in the same way as when the
lamp is turned on. You can also record with the
flash.
(Still)
31
3
Recording in dark places
(NightShot)
Adjusting the exposure for
backlit subjects
Infrared port
To adjust the exposure for backlit subjects,
press BACK LIGHT to display .. To
cancel the back light function, press BACK
LIGHT again.
Set the NIGHTSHOT switch to ON (
appears).
b Notes
Recording in mirror mode
• The NightShot and Super NightShot functions
use infrared light. Therefore, do not cover the
infrared port with your fingers or other objects.
• Remove the conversion lens (optional).
• Adjust the focus manually ([FOCUS], p. 72)
when it is hard to focus automatically.
• Do not use the NightShot and Super NightShot
functions in bright places. This may cause a
malfunction.
z Tips
Open the LCD panel 90 degrees to the
camcorder (1), then rotate it 180 degrees
to the lens side (2).
• To record an image brighter, use Super
more faithfully to the original colors, use Color
z Tips
• A mirror-image of the subject appears on the
LCD screen, but the image will be normal when
recorded.
32
Recording the fast action in
slow-motion (SMTH SLW REC)
Fast moving subjects and actions, which
cannot be captured under the ordinary
shooting conditions, can be shot in smooth
moving slow-motion for about 3 seconds.
This is useful to shoot fast actions such as a
golf or tennis swing.
[3sec AFTER]
[3sec BEFORE]
• [RECORD SOUND]
(HOME)
Select [ON] (
) to superimpose sounds
such as conversation on the slow motion
pictures (The default setting is [OFF]).
Your camcorder records sounds for about
12 seconds while [Recording···] is
displayed in step 3.
(HOME)
b Notes
1 Slide the POWER switch to turn on the
• Sounds cannot be recorded while shooting a 3
second-movie (approx.).
• Image quality of [SMTH SLW REC] is not as
good as that of normal recording.
camcorder.
2 Touch
t [SMTH SLW REC].
(HOME) t
(CAMERA)
3 Press START/STOP.
A 3 second-movie (approx.) is recorded as
a 12 second-slow-motion-movie.
[Recording···] disappears, when recording
is finished.
Touch
recording.
to cancel the smooth slow
To change the setting
On the [SMTH SLW REC] screen, touch
(OPTION) t
tab, then select the
setting you want to change.
• [TIMING]
Select the recording start point after
START/STOP is pressed. The default
setting is [3sec AFTER].
33
Recording/Playback
Playback
Lens cover
Power zoom lever E
POWER switch F
Closes when the INDEX screen appears.
(HOME) B
(HOME) A
(Film Roll Index) D
(VIEW IMAGES) G
(VIEW IMAGES) C
1
2
Slide the POWER switch F to turn on your camcorder.
Display the desired INDEX screen.
Playing back images from VISUAL INDEX
Press
(VIEW IMAGES) G (or C).
The VISUAL INDEX screen appears on the LCD screen (It may take some time to display the
thumbnails).
Appears with the image on the tab that was lastly played back/recorded
(B for the still image)
Returns to the
recording screen
Selects images by date
Previous 6 images
Next 6 images
Returns to the
recording screen
(OPTION)
Displays movies with HD (high
definition) image quality*
Displays still images
34
*
appears for movies with SD (standard definition) image quality. To play back movies of another
image quality, touch
the INDEX screen.
(OPTION) t
tab t [
/
INDEX SET] when displaying movies on
z Tips
• The number of the images on the VISUAL INDEX screen can be changed 6 y 12 by moving the power
zoom lever E. To fix this number, touch (HOME) A (or B) t (SETTINGS) t [VIEW
Playing back images from Film Roll Index
Press
(Film Roll Index) D.
The [ INDEX] screen appears (It may take some time to display the thumbnails).
Recorded movies are listed by time and are displayed as an INDEX screen. You can start
playing back a movie from the selected image.
Displays the previous/next image.
Returns to the recording
screen
Selects movies
by date (p. 37)
Previous scene
Next scene
(OPTION)
b Notes
• [ INDEX] is available only for movies.
z Tips
• Touch
(OPTION) t [
• To display the movies with SD (standard definition) image quality, touch
INDEX SET] on the INDEX screen.
(OPTION) t [
/
35
3
Start playing back.
Movies
Touch the
or
tab to play back movies.
Toggles Play or Pause as you touch
Return (to the INDEX screen)
Beginning of the scene/
previous scene
Next scene
Stop (go to the INDEX screen)
(OPTION)
Reverse/Forward
z Tips
• When playback from the selected movie reaches the last movie, the screen returns to the INDEX screen.
• Touch
/
during pause to play back movie slowly.
• A touch of
/
makes the reverse/fast forward approximately 5 times faster, 2 touches makes it
approximately 10 times faster, 3 touches makes it approximately 30 times faster, and 4 touches makes it
approximately 60 times faster.
Still images
On the VISUAL INDEX screen, touch the
images.
tab to play back still
Return (to the VISUAL
INDEX screen)
Slide show (p. 38)
(OPTION)
Goes to the VISUAL INDEX
screen
Previous/Next
To adjust the sound volume
Touch
(OPTION) t
tab t [VOLUME], then adjust the volume with
/
.
z Tips
• You can switch the playback mode by touching
[VISUAL INDEX]/[ INDEX].
(HOME) A (or B) t
(VIEW IMAGES) t
36
Playing back from a face image
(Face Index)
Using PB zoom
You can magnify still images from about
1.1 to 5 times the original size.
Magnification can be adjusted with the
power zoom lever or the zoom buttons
beside the LCD screen.
The detected face images are displayed on
the INDEX screen.
You can play back the movie from the
selected face image.
1 Turn on your camcorder.
2 Touch
(HOME) A (or B) t
(VIEW IMAGES) t [
INDEX].
Returns to the recording screen
1 Play back the still images you want to
Previous/
Next scene
magnify.
Previous/
Next display
2 Magnify the still image with T
(Telephoto).
3 Touch v/V to select the desired scene.
The screen is framed.
4 Touch b/B to search for the desired
face image, then touch the face image
you want to play back.
3 Touch the screen at the point you want
to display in the center of the displayed
frame.
Playback starts from the selected face
image.
4 Adjust the magnification with W (Wide
angle)/T (Telephoto).
b Notes
To cancel, touch
.
• Faces may not be detected depending on
recording conditions.
Example: People wearing glasses or hats, or not
facing towards the camera.
Searching for desired movies by
date (Date Index)
• Set [
setting) before recording to play back movies
INDEX SET] to [ON] (the default
You can search for desired movies by date
efficiently.
The face images do not appear if faces have not
been detected.
(VIEW IMAGES)
z Tips
• You can play back movies of another image
quality by touching
(OPTION) t [
/
INDEX SET] on the [
INDEX] screen.
37
1 Slide the POWER switch to turn on the
Playing back a series of still
images (Slide show)
camcorder, and press
IMAGES).
(VIEW
The VISUAL INDEX screen appears on
the LCD screen.
2 Touch the
or
tab.
3 Touch [DATE].
The recording dates of movies are
displayed on the screen.
Return to the VISUAL INDEX screen
Touch
screen.
on the still image playback
The slide show begins from the selected
image.
Previous/Next Date
Touch
to stop the slide show. To
4 Touch v/V to select the date of the
restart, touch
again.
desired movie.
b Notes
5 Touch
while the selected date of
• You cannot operate playback zoom during slide
show.
the desired movie is highlighted.
The movies of selected date are
displayed on the VISUAL INDEX
screen.
z Tips
• You can set continuous slide show playback by
touching
(OPTION) t
tab t [SLIDE
z Tips
• On the [
SHOW SET]. The default setting is [ON]
(continuous playback).
• You can also play back the slide show by
INDEX]/[
INDEX] screen, you
can use the Date Index function by following
the steps 3 to 5.
• To search for movies of another image quality,
touch
INDEX SET] when displaying movies on the
INDEX screen.
touching
(OPTION) t
tab t [SLIDE
SHOW] on the VISUAL INDEX screen.
(OPTION) t
tab t [
/
38
Playing the image on a TV
Connection methods and quality of the
image viewed on the TV screen differ
depending on what type of TV is connected,
and the connectors used.
Use the supplied AC Adaptor as the power
source (p. 16).
HDMI OUT
A/V OUT
Refer also to the instruction manuals
supplied with the device to be connected.
b Notes
• When recording, set [X.V.COLOR] to [ON] to
Some settings may need to be adjusted on the
TV when playing back. Refer to the instruction
manual of your TV for details.
Open the jack cover.
Operation flow
You can connect your camcorder to the TV
easily following the instructions displayed
on the LCD screen, [TV CONNECT
Guide].
Switch the input on the TV to the
connected jack.
Refer to the instruction manuals of the
Handycam
Station
TV.
r
Connect your camcorder and TV
referring to [TV CONNECT Guide].
r
Make the required output settings
b Notes
on your camcorder (p. 41).
• Only the Handycam Station is equipped with the
COMPONENT OUT jack.
• The Handycam Station and your camcorder are
both equipped with A/V OUT jacks. Connect
the A/V connecting cable either to the
Handycam Station or to your camcorder,
depending on your setup. If you connect A/V
connecting cables to both the Handycam Station
and your camcorder at the same time, image
disturbance may occur.
39
Selecting the most
advantageous connection - [TV
CONNECT Guide]
Your camcorder will advise you of the most
advantageous way of connecting your TV.
1
Turn on your camcorder, and
press
(HOME).
2
3
Touch
(OTHERS).
Touch [TV CONNECT Guide].
If the item is not on the screen, touch v/
V to change the page.
4
Select the TV type you use.
Meanwhile, you can make the relevant
connection between your camcorder and
the TV.
40
Connecting to a high definition TV
Images recorded with HD (high definition) image quality are played back with HD (high
definition) image quality. Images recorded with SD (standard definition) image quality are
played back with SD (standard definition) image quality.
: Signal flow
HOME MENU setting
Type Camcorder
Cable
TV
(SETTINGS) t
[OUTPUT SETTINGS]
t [COMPONENT] t
[1080i/576i] (p. 68)
Component video cable
(supplied)
(Green) Y
(Blue) PB/CB
(Red) PR/CR
A/V connecting cable
(supplied)
(White)
(Red)
(Yellow)
• An A/V connecting cable is also needed to output audio signals. Connect the white and red plugs of the A/
V connecting cable to the audio input jack of your TV.
41
: Signal flow
HOME MENU setting
Type Camcorder
Cable
TV
HDMI IN
HDMI OUT
HDMI cable (optional)
• Use an HDMI cable with the HDMI logo.
• Use an HDMI cable with an HDMI mini connector on one end (to be connected to the camcorder), and a
connector suitable for connecting your TV.
• Images are not output from the HDMI OUT jack, if copyright protection signals are recorded in the
images.
• Some TVs may not function correctly (e.g., no sound or image) with this connection.
• Do not connect the HDMI OUT jack of your camcorder and HDMI OUT jack of the external device with
the HDMI cable. This may cause a malfunction.
Connecting to a non-high-definition 16:9 (wide) TV or 4:3 TV
Images recorded with HD (high definition) quality are converted to SD (standard definition)
and played back. Images recorded with SD (standard definition) image quality are played back
with SD (standard definition) image quality.
To set the aspect ratio according to the connected TV (16:9/4:3)
Set [TV TYPE] to [16:9] or [4:3] according to your TV (p. 67).
• When you play back a movie recorded with SD (standard definition) image quality on a 4:3 TV that is not
compatible with the 16:9 signal, touch
(HOME) t
(SETTINGS) t [MOVIE SETTINGS] t
42
: Signal flow
HOME MENU setting
Type Camcorder
Cable
TV
(SETTINGS) t
[OUTPUT SETTINGS]
t [COMPONENT] t
[576i] (p. 68)
Component video cable
(supplied)
(Green) Y
(Blue) PB/CB
(Red) PR/CR
(SETTINGS) t
[OUTPUT SETTINGS]
t [TV TYPE] t [16:9]/
A/V connecting cable
(supplied)
(White)
(Red)
(Yellow)
• An A/V connecting cable is also needed to output audio signals. Connect the white and red plugs of the A/
V connecting cable to the audio input jack of your TV.
(SETTINGS) t
A/V connecting cable with
S VIDEO (optional)
[OUTPUT SETTINGS]
t [TV TYPE] t [16:9]/
(White)
(Red)
(Yellow)
• When the S VIDEO plug (S VIDEO channel) is connected, audio signals are not output. To output audio
signals, connect the white and red plugs of an A/V connecting cable with the S VIDEO cable to the audio
input jack of your TV.
• This connection produces higher resolution images compared with the A/V connecting cable (Type
).
A/V connecting cable
(supplied)
(SETTINGS) t
[OUTPUT SETTINGS]
(Yellow)
(White)
(Red)
t [TV TYPE] t [16:9]/
* Set this according to your TV.
43
When connecting to your TV via a VCR
Connect your camcorder to the LINE IN input on the VCR using the A/V connecting cable.
Set the input selector on the VCR to LINE (VIDEO 1, VIDEO 2, etc.).
When your TV is monaural (When your TV has only one audio input jack)
Connect the yellow plug of the A/V connecting cable to the video input jack and connect the
white (left channel) or red (right channel) plug to the audio input jack of your TV or VCR.
If your TV/VCR has a 21-pin adaptor (EUROCONNECTOR)
Use the 21-pin adaptor supplied with your camcorder (For models with the
on their bottom surfaces only). This adaptor is designed for output use only.
mark printed
b Notes
• When the A/V connecting cable is used to output images, images are output with SD (standard definition)
image quality.
z Tips
• If you connect your camcorder to your TV using more than one type of cable to output images, the order
of priority of the output signal is as follows:
HDMI t component video t S VIDEO t audio/video.
• HDMI (High Definition Multimedia Interface) is an interface to send both video/audio signals. The
HDMI OUT jack outputs high quality images and digital audio. If you connect your camcorder to a Sony
TV having a Video-A mode, an optimum image quality will be selected automatically. Refer to the
instruction manual of your TV for details.
44
Saving images
Recorded images are stored on the “Memory Stick PRO Duo.” Due to the limited capacity of
the “Memory Stick PRO Duo,” make sure that you save the image data to some type of external
media such as a DVD-R or a computer.
You can save the images recorded on the camcorder as described below.
Saving images using a computer
By using “Picture Motion Browser” on the supplied CD-ROM, you can save the images
recorded on the “Memory Stick PRO Duo.”
For HDR-CX7E/CX7EK
You can rewrite movies with HD (high definition) image quality from the computer to your
camcorder, if necessary.
Creating a disc with One Touch
(One Touch Disc Burn)
You can save images recorded on the camcorder directly to a disc
with ease.
Saving images on a computer (Easy PC Back-up)
You can save images recorded on the camcorder on the hard disk of a
computer.
Creating a disc with selected images
You can save images copied to your computer on a disc. You can also
edit those images.
Images can be saved in HD (high definition) image quality or SD
(standard definition) image quality. See “Picture Motion Browser
Guide” stored on the supplied CD-ROM.
Saving images by connecting your camcorder to other devices
Dubbing to VCR or DVD/HDD devices
This is a convenient way of distributing dubbed discs.
When connecting with an A/V connecting cable, images can be saved in
SD (standard definition) image quality. See “Dubbing to VCR or DVD/
45
Editing (OTHERS) category Deleting images
This category enables you to edit the
images, to print still images and to connect
your camcorder to a computer.
You can increase the free space on the
“MemoryStickPRODuo”bydeletingimage
data.
You can check the free space on the
“Memory Stick PRO Duo” using
[
b Notes
• You cannot restore images once they are deleted.
• Important data should besaved on external media
(OTHERS) category
• Donottrytodeletethefilesonthe“MemoryStick
PRO Duo” in your camcorder using a computer.
Item list
DELETE
You can delete images on the “Memory
1
2
Touch
(OTHERS) t [DELETE].
(HOME) t
EDIT
Touch [
DELETE] or
You can edit the images on the “Memory
[
[
DELETE] to delete movies, or
DELETE] to delete still
images.
PLAYLIST EDIT
You can create and edit a Playlist (p. 49).
3
Touch the image to be deleted.
PRINT
You can print still images on a connected
COMPUTER
You can connect your camcorder to a
computer.
See “Operating Guide” for connecting the
computer.
The selected image is marked with
Press and hold the image on the LCD
screen to confirm the image.
.
TV CONNECT Guide
Touch
to return to the previous
screen.
Your camcorder helps you select the
appropriate connection for your device
(p. 39).
4
Touch
t [YES] t
.
46
• You can delete an image when viewing it by
selecting
[DELETE] on the playback screen.
To delete all images of the same type
(on each tab) at one time
(OPTION) t tab t
DELETE ALL]/[ DELETE ALL]
t [YES] t [YES] t
DELETE ALL]/
• To delete all images recorded on the “Memory
Stick PRO Duo,” format the “Memory Stick
[
.
To delete all the movies or the still
images recorded on the same day at
one time
1 Touch
(HOME) t
(OTHERS)
t [DELETE].
2 Touch the type of image you want to
delete ([ DELETE by date]/
DELETE by date]).
[
Previous/Next Date
3 Touch v/V to select the recording date
of the desired image.
4 Touch
while the selected recording
date is highlighted.
The images recorded on the selected
date are displayed on the screen.
Touch the image on the LCD screen to
confirm the image. Touch
to the previous screen.
to return
5 Touch
t [YES] t
.
b Notes
• Do not remove the battery pack or the AC
Adaptor, or eject the “Memory Stick PRO Duo”
from your camcorder while deleting the images.
It may damage the “Memory Stick PRO Duo.”
• If the deleted movie is included in the Playlist
Playlist.
• You cannot delete images if write-protection is
set to the images by another device.
z Tips
• You can select up to 100 images at one time.
47
Dividing a movie
b Notes
• You cannot restore movies once they are
divided.
• Do not remove the battery pack or the AC
Adaptor, or eject the “Memory Stick PRO Duo”
from your camcorder while dividing the movie.
It may damage the “Memory Stick PRO Duo.”
You can divide movies on the “Memory
Stick PRO Duo.”
b Notes
• During Easy Handycam operation, you cannot
divide movies. Cancel Easy Handycam
• If the divided original movie is included in the
Playlist, the movie in the Playlist will also be
divided.
1
2
3
4
Touch
(OTHERS) t [EDIT].
(HOME) t
• A slight difference may occur from the point
where you touch
and the actual dividing
point, as your camcorder selects the dividing
point based on about half-second increments.
Touch [DIVIDE] t [
DIVIDE]/
• Movies in a Playlist may not be divided because
of the limitation of the movie numbers that can
be added in a Playlist. In this case, first erase
unwanted movies from the Playlist before
dividing movies.
[
DIVIDE].
Touch the movie to be divided.
The selected movie starts playback.
Touch
at the point where you
want to divide the movie into
scenes.
The movie pauses.
Adjusts the dividing point with more
precision after the dividing point has
been selected with
.
Returns to the beginning of the
selected movie.
Play and pause toggles as you press
.
5
Touch
t [YES] t
.
48
Creating the Playlist
A Playlist is a list showing thumbnails of
the movies that you have selected. The
original scenes are not changed even if you
edit or delete the scenes in the Playlist.
To add all the movies recorded on the
same day at one time
1 Touch
(HOME) t
(OTHERS)
t [PLAYLIST EDIT].
b Notes
2 Touch [ ADD by date] or
ADD by date].
• During Easy Handycam operation, you cannot
add movies to the Playlist or edit the Playlist.
• Images with HD (high definition) image quality
and SD (standard definition) image quality are
added to an individual Playlist.
[
The recording dates of movies are
displayed on the screen.
z Tips
• The images recorded by this camcorder and
stored onto the “Memory Stick PRO Duo” are
called “original.”
Previous/Next Date
3 Touch v/V to select the recording date
1
2
Touch
(HOME) t
of the desired movie.
(OTHERS) t [PLAYLIST EDIT].
4 Touch
while the selected recording
date is highlighted.
The movies recorded on the selected
date are displayed on the screen.
Touch the image on the LCD screen to
confirm the movie.
Touch [
ADD] or [
ADD].
Touch
screen.
to return to the previous
3
Touch the image to be added to
the Playlist.
.
5 Touch
t [YES] t
.
b Notes
• Do not remove the battery pack or the AC
Adaptor, or eject the “Memory Stick PRO Duo”
from your camcorder while editing the Playlist.
It may damage the “Memory Stick PRO Duo.”
• You cannot add still images to a Playlist.
The selected image is marked with
Press and hold the image on the LCD
screen to confirm the image.
.
z Tips
• You can add a maximum of 999 movies with
HD (high definition) image quality, or 99
movies with SD (standard definition) image
quality to the Playlist.
Touch
to return to the previous
screen.
• You can add a movie also in the following steps:
– On the playback screen, touch
tab t [ ADD]/[
– On the INDEX screen, touch
(OPTION)
ADD].
(OPTION)
ADD]/
4
Touch
t [YES] t
.
t
t
tab t [
ADD]/[
[
ADD by date]/[
ADD by date].
• You can copy the Playlist to a disc as it is, by
using the supplied software.
49
Press and hold the image on the LCD
screen to confirm the image.
Playing the Playlist
Touch
to return to the previous
screen.
1
Touch
IMAGES) t [PLAYLIST].
(HOME) t
(VIEW
4 Touch
t [YES] t
.
The Playlist screen appears.
z Tips
• The original scenes are not changed even if you
erase the scenes from the Playlist.
To change the order within the Playlist
1 Touch
(HOME) t
(OTHERS)
t [PLAYLIST EDIT].
2 Touch [ MOVE] or [
MOVE].
2
Touch the image from which you
want to playback.
3 Select the image to be moved.
The Playlist is played back from the
selected image to the end, then the
screen returns to the Playlist screen.
The selected scene is marked with
.
z Tips
Press and hold the image on the LCD
screen to confirm the image.
• You can play back movies of another image
quality by touching
(OPTION) t
tab
t [ INDEX SET].
/
Touch
to return to the previous
screen.
To erase unnecessary images from
the Playlist
4 Touch
.
5 Select the destination with
/
.
1 Touch
(HOME) t
(OTHERS)
t [PLAYLIST EDIT].
2 Touch [ ERASE] or [
ERASE].
To erase all the images from the
Playlist, touch [ ERASE ALL]/
ERASE ALL] t [YES] t
[YES] t
[
.
Destination bar
3 Select the scene to be deleted from the
6 Touch
t [YES] t
.
Playlist.
z Tips
• When you select multiple images, the images
are moved following the order appearing in the
Playlist.
The selected scene is marked with
.
50
Editing
Dubbing to VCR or DVD/HDD recorders
You can dub images played back on your camcorder to other recording devices, such as VCRs
or DVD/HDD recorders. This is a convenient way of distributing dubbed discs. Connect the
device in either of the following ways.
Connect your camcorder to the wall socket using the supplied AC Adaptor for this operation
b Notes
• Movies recorded with HD (high definition) image quality will be dubbed with SD (standard
definition) image quality.
• To copy a movie recorded with HD (high definition) image quality, install the application software
(supplied) on your computer, and copy the images to a disc in the computer.
• Since dubbing is performed via analog data transfer, the image quality may deteriorate.
A/V OUT jack
(Yellow)
(White) (Red)
IN
IN
(Yellow) (White) (Red)
S VIDEO
VIDEO
AUDIO
VIDEO
AUDIO
Devices with an S VIDEO jack
Deviceswithout an
S VIDEO jack
VCRs or DVD/
HDD recorders
: Video/Signal flow
A A/V connecting cable (supplied)
The Handycam Station and your
A/V connecting cable with an S VIDEO
cable (optional). The yellow plug
camcorder are both equipped with A/V
A/V connecting cable either to the
Handycam Station or to your
connection is not necessary. S VIDEO
connection only will not output audio.
b Notes
• You cannot dub to recorders connected with an
HDMI cable.
• To hide the screen indicators (such as a counter,
etc.) on the screen of the monitor device
camcorder, depending on your setup.
B A/V connecting cable with S
VIDEO (optional)
When connecting to another device via
the S VIDEO jack, by using an A/V
connecting cable with an S VIDEO
cable (optional), higher quality images
can be produced than with an A/V
connecting cable. Connect the white and
red plug (left/right audio) and the S
VIDEO plug (S VIDEO channel) of the
connected, touch
(HOME) t
(SETTINGS) t [OUTPUT SETTINGS] t
[DISP OUTPUT] t [LCD PANEL] (the
• To record the date/time and camera settings
• When you are connecting your camcorder to a
monaural device, connect the yellow plug of the
51
Printing recorded
images (PictBridge
compliant printer)
You can print out still images using a
PictBridge compliant printer, without
connecting the camcorder to a computer.
A/V connecting cable to the video input jack,
and the red (right channel) or the white (left
channel) plug to the audio input jack on the
device.
1
Turn on your camcorder, and
press (VIEW IMAGES).
Connect your camcorder to the AC Adaptor
to obtain power from the wall socket
(p. 16). Turn on the printer.
Insert the “Memory Stick PRO Duo”
containing the still images you want to print
into your camcorder.
Set [TV TYPE] according to the display
device (p. 67).
2
3
Insert the recording media in the
recording device.
If your recording device has an input
selector, set it to the input mode.
1
2
3
Connect the Handycam Station to
the wall socket using the supplied
AC Adaptor.
Connect your camcorder to the
recording device (VCR or DVD/
HDD recorder) with the A/V
connecting cable (supplied) 1 or
an A/V connecting cable with S
VIDEO (optional) 2.
Set the camcorder onto the
Handycam Station securely, then
turn on your camcorder.
Connect your camcorder to the input
jacks of the recording device.
Connect the (USB) jack of the
Handycam Station to the printer
using the USB cable (p. 101).
[USB SELECT] appears on the screen
automatically.
4
5
Start the playback on your
camcorder, and record it on the
recording device.
Refer to the instruction manuals
supplied with your recording device for
details.
4
Touch [PRINT].
When connection is complete,
(PictBridge connecting) appears on
the screen.
When dubbing is finished, stop
the recording device, and then
your camcorder.
You can select a still image on the
screen.
52
• Do not attempt the following operations when
is on the screen. The operations may not be
performed properly.
5
Touch the still image to be
printed.
– Operate the POWER switch.
– Press
(VIEW IMAGES).
– Remove your camcorder from the Handycam
Station.
– Disconnect the USB cable from the
Handycam Station or the printer.
• If the printer stops working, disconnect the USB
cable, turn the printer off and on again, and
restart the operation from the beginning.
The selected image is marked with
.
• You can select only the paper sizes that the
printer can print.
Press and hold the image on the LCD
screen to confirm the image.
• On some printer models, the top, bottom, right,
and left edges of images may be trimmed. If you
print a still image recorded in a 16:9 (wide)
ratio, the left and right ends of the image may be
trimmed widely.
Touch
to return to the previous
screen.
• Some printer models may not support the date
printing function. Refer to your printer’s
instruction manual for details.
• The images described below may not be printed
out:
– The image edited by a computer
– The image recorded by other devices
– The image file exceeding 3 MB
– The image file larger than 2,848 × 2,136
pixels
6
7
Touch
(OPTION), set the
following options, then touch
.
[COPIES]: Set number of copies of a
still image to be printed. You can set up
to 20 copies.
[DATE/TIME]: Select [DATE],
[DAY&TIME], or [OFF] (no date/time
printed).
[SIZE]: Select the paper size.
z Tips
If you do not change the setting, go to
step 7.
• PictBridge is an industry standard established
by the Camera & Imaging Products Association
(CIPA). You can print still images without using
a computer by connecting a printer directly to a
digital video camera or digital still camera,
regardless of model or manufacturer.
Touch [EXEC] t [YES] t
The image selection screen appears
again.
.
• You can print a still image on the still image
playback screen by touching
(OPTION) t
tab t [PRINT].
To finish printing
Touch
on the image selection screen.
b Notes
• We can guarantee the operation of only models
that are PictBridge compatible.
• Refer also to the instruction manual of the
printer to be used.
53
Utilizing Recording Media
(MANAGE
Formatting the
“Memory Stick PRO
Duo”
You can delete all the images on the
“Memory Stick PRO Duo” to recover
recordable free space.
MEMORY STICK)
category
This category enables you to use the
“Memory Stick PRO Duo” for various
purposes.
Connect your camcorder to the wall socket
using the supplied AC Adaptor for this
b Notes
• To avoid the lossof important images, you should
(MANAGE MEMORY STICK)
category
[
1
2
FORMAT].
Turn on your camcorder.
Item list
FORMAT
You can format the “Memory Stick PRO
Duo” and recover the recordable free space
(p. 55).
Insert the “Memory Stick PRO
Duo” to be formatted into your
camcorder.
INFO
3
Touch
(MANAGE MEMORY STICK) t
FORMAT].
(HOME) t
You can display the “Memory Stick PRO
[
REPAIR IMG.DB F.
You can repair the management
information on the “Memory Stick PRO
4
5
Touch [YES] t [YES].
When [Completed.] appears,
touch
.
b Notes
• Even the still images protected with another
device against accidental deletion are also
deleted.
54
Checking the
“Memory Stick PRO
Duo” information
You can display the “Memory Stick PRO
Duo” information, and check the free space
on the “Memory Stick PRO Duo.”
• Do not attempt the following operations when
[Executing...] is on the screen:
– Operate the POWER switch or buttons
– Eject the “Memory Stick PRO Duo”
• While [
FORMAT] is activated, do not
disconnect the AC Adaptor.
1
2
Turn on your camcorder.
Touch
(MANAGE MEMORY STICK)t
INFO].
(HOME) t
[
To turn off the display
Touch
.
b Notes
• The calculation for space available on a
“Memory Stick PRO Duo” is 1MB = 1,048,576
bytes. The fractions less than 1 MB are
discarded when the “Memory Stick PRO Duo”
space is displayed. Therefore, the displayed size
of the total space available on a “Memory Stick
PRO Duo,” both free and used, will be slightly
smaller than the advertized size of the “Memory
Stick PRO Duo.”
• Since there is a management file area, the used
space is not displayed as 0 MB even if you
perform [
55
Repairing the image database file
b Notes
This function checks the management
information and the consistency of movies
in the “Memory Stick PRO Duo,” and
repairs any inconsistencies found.
• Do not apply mechanical shock or vibration to
the camcorder during this operation.
• Do not disconnect the AC Adaptor or remove
the battery pack, or eject the “Memory Stick
PRO Duo” during this operation.
1
2
Turn on your camcorder.
Touch
(HOME) t
(MANAGE MEMORY STICK)
t [REPAIR IMG.DB F.].
The [REPAIR IMG.DB F.] screen
appears.
Do you want to check the Image Database File?
YES
NO
REPAIR IMG.DB F.
3
Touch [YES].
Your camcorder will check the
management file.
If no inconsistency was found, touch
to finish the operation.
4
5
Touch [YES].
When [Completed.] appears,
touch
.
56
Customizing Your Camcorder
What you can do with the
(SETTINGS)
category of the
HOME MENU
You can change the recording functions and
the operating settings for your convenience.
3
4
5
Touch the desired setup item.
If the item is not on the screen, touch v/
V to change the page.
Using the HOME MENU
1
Turn on your camcorder, then
press
(HOME).
(HOME)
Touch the desired item.
If the item is not on the screen, touch v/
V to change the page.
(HOME)
(SETTINGS) category
Change the setting, then touch
.
2
Touch
(SETTINGS).
57
List of the
(SETTINGS)
category items
Items
Page
1
/
INDEX SET*
DATA CODE
DISPLAY
Items
Page
1
/
REC SET*
1
INTERVAL SET*
REC MODE
SOUND/DISP SET*2 (p. 66)
REC MODE
NIGHTSHOT LIGHT
WIDE SELECT
DIGITAL ZOOM
STEADYSHOT
AUTO SLW SHUTTR
X.V.COLOR
Items
Page
1
VOLUME*
1
BEEP*
LCD BRIGHT
LCD BL LEVEL
LCD COLOR
GUIDEFRAME
ZEBRA
REMAINING
Items
Page
FLASH LEVEL
REDEYE REDUC
TV TYPE
DISP OUTPUT
COMPONENT
1
INDEX SET*
Items
Page
1
Items
Page
IMAGE SIZE*
1
CLOCK SET*
QUALITY
FILE NO.
AREA SET
SUMMERTIME
NIGHTSHOT LIGHT
STEADYSHOT
GUIDEFRAME
ZEBRA
1
LANGUAGE SET*
FLASH LEVEL
REDEYE REDUC
58
MOVIE SETTINGS
(Items for recording movies)
Items
Page
DEMO MODE
REC LAMP
CALIBRATION
A.SHUT OFF
REMOTE CTRL
Touch 1, then 2.
If the item is not on the screen, touch v/V
to change the page.
*1 You can set these items also during Easy
*2 The menu name is changed to [SOUND
SETTINGS] during Easy Handycam operation.
How to set
The default settings are marked with B.
/
REC SET
You can select a recording quality to record
a movie.
B
HD QUALITY
Records with HD (high definition) image
quality.
SD QUALITY
Records with SD (standard definition)
image quality.
REC MODE
You can select a recording mode to record a
movie with HD (high definition) image
quality from 4 levels.
HD XP
Records in the highest quality mode
(AVC HD 15M (XP)).
HD HQ
Records in high quality mode
(AVC HD 9M (HQ)).
BHD SP
Records in standard quality mode
(AVC HD 7M (SP)).
59
b Notes
HD LP
Increases the recording time (Long Play)
(AVC HD 5M (LP)).
• Do not cover the infrared port with your fingers
• Remove the conversion lens (optional).
• The maximum shooting distance using
b Notes
• If you record in the LP mode, details in scenes
with quick movements may appear rough when
you play back the movie.
[NIGHTSHOT LIGHT] is about 3 m (10 feet).
WIDE SELECT
z Tips
When recording with SD (standard
definition) image quality, you can select the
aspect ratio according to the TV connected.
Refer also to the instruction manuals
supplied with your TV.
each recording mode.
REC MODE
You can select a recording mode to record a
movie with SD (standard definition) image
quality from 3 levels.
B16:9 WIDE
Records images to the full screen on a 16:9
(wide) TV screen.
SD HQ
4:3 (
)
Records in high quality mode
(SD 9M (HQ)).
Records images to the full screen on a 4:3
TV screen.
BSD SP
b Notes
Records in standard quality mode
(SD 6M (SP)).
• Set [TV TYPE] correctly according to the TV
SD LP
DIGITAL ZOOM
Increases the recording time (Long Play)
(SD 3M (LP)).
You can select the maximum zoom level in
case you want to zoom to a level greater
than 10 × (the default setting) during
recording. Note that the image quality
decreases when you use the digital zoom.
b Notes
• If you record in the LP mode, the quality of
scenes may be degraded, or scenes with quick
movements may appear with a block noise when
you play back the movie.
z Tips
each recording mode.
The right side of the bar shows the digital
zooming factor. The zooming zone
appears when you select the zooming
level.
NIGHTSHOT LIGHT
record, you can record clearer images by
setting [NIGHTSHOT LIGHT], which
emits infrared light (invisible), to [ON] (the
default setting).
BOFF
Up to 10 × zoom is performed optically.
60
z Tips
20 ×
Up to 10 × zoom is performed optically,
and after that, up to 20 × zoom is
performed digitally.
• Positioning the subject at the cross point of the
guide frame makes a balanced composition.
ZEBRA
STEADYSHOT
Diagonal stripes appear in portions of the
screen where brightness is at a preset level.
This is useful as a guide when adjusting the
brightness. When you change the default
You can compensate for camera shake (the
default setting is [ON]). Set
[STEADYSHOT] to [OFF] ( ) when
using a tripod (optional), then the image
becomes natural.
setting,
is displayed. The zebra pattern
is not recorded.
BOFF
AUTO SLW SHUTTR
(Auto Slow Shutter)
The zebra pattern is not displayed.
70
When recording in dark places, the shutter
speed is automatically reduced to 1/25
second (The default setting is [ON]).
The zebra pattern appears at a screen
brightness level of about 70 IRE.
100
The zebra pattern appears at a screen
brightness level of about 100 IRE or
higher.
X.V.COLOR
When recording, set to [ON] to capture
wider range of colors. Various colors such
as the brilliant color of flowers and
turquoise blue of the sea can be more
faithfully reproduced.
b Notes
• Portions of the screen where brightness is about
100 IRE or above may appear overexposed.
z Tips
b Notes
• IRE represents the unit of images brightness
amplitude.
• Set [X.V.COLOR] to [ON] only when the
recorded content will be played back on an
x.v.Color-compliant TV. Otherwise, set to
[OFF] (the default setting).
REMAINING
• If the movie recorded with this function [ON] is
played back on an non-x.v.Color-compliant TV,
the color may not be reproduced correctly.
• [X.V.COLOR] cannot be set to [ON]:
– while recording with SD (standard definition)
image quality
BAUTO
Displays the remaining recording time of
movies for about 8 seconds in situations
such as those described below.
– When your camcorder recognizes the
remaining “Memory Stick PRO Duo”
capacity with the POWER switch set to
(Movie).
– When you press DISP/BATT INFO to
switch the indicator from off to on with
the POWER switch set to
– while recording a movie
GUIDEFRAME
You can display the frame and check that
the subject is horizontal or vertical by
setting [GUIDEFRAME] to [ON].
The frame is not recorded. Press DISP/
BATT INFO to make the frame disappear
(The default setting is [OFF]).
(Movie).
– When you select the movie recording
mode on the HOME MENU.
61
S
ON
INDEX SET
Always displays the remaining “Memory
Stick PRO Duo” indicator.
The default setting is [ON], allowing you to
detect faces during movie recording.
b Notes
Face icons and their meanings
• When the remaining recordable time for movies
is less than 5 minutes, the indicator stays on the
screen.
: When the setting is [ON].
: When the first face is detected.
: The icon flashes when a face is
detected.
FLASH LEVEL
: Faces cannot be detected.*
You can set this function when you use the
built-in flash, or an external flash (optional)
that is compatible with your camcorder.
* Your camcorder can detect up to about 100
faces for each scene.
To play back scenes using Face Index, see
HIGH(
)
Makes the flash level higher.
BNORMAL(
LOW(
)
)
Makes the flash level lower.
REDEYE REDUC
You can set this function when you use the
built-in flash, or an external flash (optional)
that is compatible with your camcorder.
You can prevent redeye by activating the
flash before recording.
Set [REDEYE REDUC] to [ON], then press
setting.
(Auto redeye reduction): Pre-flashes to
reduce redeye before the flash automatically
flashes when there is insufficient ambient
light.
r
(Forced redeye reduction): Always
uses the flash and the redeye reducing pre-
flash.
r
(No flash): Records without flash.
b Notes
• The redeye reduction may not produce the
desired effect due to individual differences and
other conditions.
62
PHOTO SETTINGS
(Items for recording still images)
Capacity of the “Memory Stick PRO
Duo” (MB) and the number of
recordable images
When the POWER switch is
(Still)
VGA
Touch 1, then 2.
If the item is not on the screen, touch v/V
to change the page.
6.1M
4.6M
3.1M
(0.3M)
640 ×
480
2848 × 2848× 2048 ×
2136
6.1M
1602
4.6M
1536
3.1M
How to set
512MB
1GB
145
375
195
495
280
730
2750
6900
305
405
580
5700
770 1000
640 850
1600 2100
1500
14000
The default settings are marked with B.
2GB
1200
3100
11500
29500
IMAGE SIZE
4GB
1200 1650
3100 4150
2350
6100
23000
58000
B6.1M (
)
6.1M
8GB
2500 3350
4800
47000
Records still images clearly.
6400 8400 12000 115000
4.6M (
)
4.6M
Records still images clearly in the 16:9
(wide) ratio.
When the POWER switch is
(Movie)*
3.1M (
)
3.1M
4.6M
3.4M
2136 × 1602
3.4M
Allows you to record more still images in
relatively clear quality.
2848 × 1602
4.6M
VGA (0.3M) (
Allows the maximum number of still
images to be recorded.
)
512MB
1GB
195
495
260
660
405
540
1000
1350
b Notes
• [ IMAGE SIZE] can be set only during
recording standby.
2GB
850
2100
1100
2800
4GB
1650
4150
2150
5500
QUALITY
8GB
3350
8400
4450
11000
BFINE (
)
Records still images at the fine image
quality level.
* The image size is fixed depending on the aspect
ratio of the image recorded:
STANDARD (
Records still images at the standard image
quality level.
)
– [
quality
– [
4.6M] with HD (high definition) image
4.6M] in the aspect ratio 16:9 with SD
(standard definition) image quality
63
– [3.4M] in the aspect ratio 4:3 with SD
(standard definition) image quality
ZEBRA
b Notes
• All numbers measured at the following setting:
Top: [FINE] is selected for image quality.
Bottom: [STANDARD] is selected for image
quality.
FLASH LEVEL
• All numbers measured when using a “Memory
Stick PRO Duo” made by Sony Corporation.
The number of still images and the length of
time for movies may vary depending on the
shooting conditions and the recording mediums.
REDEYE REDUC
• The unique pixel array of Sony’s ClearVid
CMOS sensor and image processing system
(new Enhanced Imaging Processor) allows for
still image resolution equivalent to the sizes
described.
• For recording still images, you can use a
“Memory Stick PRO Duo” of a capacity smaller
than 256 MB.
FILE NO.
BSERIES
Assigns file numbers in sequence even if
the “Memory Stick PRO Duo” is replaced
with another one. The file number is reset
when a new folder is created or the
recording folder is replaced with another.
RESET
Assigns file numbers in sequence,
following the largest file number existing
on the current recording medium.
NIGHTSHOT LIGHT
STEADYSHOT
GUIDEFRAME
64
VIEW IMAGES SET
(Items to customize the display)
DATE/TIME
Touch 1, then 2.
If the item is not on the screen, touch v/V
to change the page.
ADate
BTime
How to set
CAMERA DATA
Movie
The default settings are marked with B.
/
INDEX SET
You can select the image quality of the
movie you play back.
B
HD QUALITY
Still image
Plays back movies recorded with HD (high
definition) image quality.
SD QUALITY
Plays back movies recorded with SD
(standard definition) image quality.
DATA CODE
CSteadyShot off
DBrightness
EWhite balance
FGain
During playback, displays the information
(data code) recorded automatically at the
time of recording.
BOFF
Data code is not displayed.
GShutter speed
HAperture value
IExposure
DATE/TIME
Displays the date and time.
z Tips
•
appears for an image recorded using a flash.
CAMERA DATA (below)
Displays camera setting data.
• The data code is displayed on the TV screen if
you connect your camcorder to a TV.
• The indicator toggles through the following
sequences as you press DATA CODE on the
Remote Commander: [DATE/TIME] t
[CAMERA DATA] t [OFF] (no indication).
65
SOUND/DISP SET
(Items to adjust the sound and the screen)
• Depending on the “Memory Stick PRO Duo”
condition, bars [--:--:--] appear.
DISPLAY
You can select the number of thumbnails
that appear on the VISUAL INDEX screen.
Touch 1, then 2.
If the item is not on the screen, touch v/V
to change the page.
BZOOM LINK
Change the number of thumbnails (6 or 12)
with the power zoom lever on your
camcorder.*
How to set
6IMAGES
Displays thumbnails of 6 images.
12IMAGES
Displays thumbnails of 12 images.
The default settings are marked with B.
* You can also operate with the zoom
buttons beside the LCD screen or on the
Remote Commander.
VOLUME
Touch
/
to adjust the volume
INTERVAL SET
You can select the duration of each
thumbnail from 3, 6, 12 seconds, 1 or 5
minutes.
BEEP
BON
The default setting is [3 sec].
A melody sounds when you start/stop
recording, or operate the touch panel.
OFF
Cancels the melody.
LCD BRIGHT
You can adjust the brightness of the LCD
screen with
/
.
1 Adjust the brightness with
/
.
2 Touch
.
z Tips
• This adjustment does not affect the recorded
images in any way.
66
OUTPUT SETTINGS
(Items for when connecting other devices)
LCD BL LEVEL
You can adjust the brightness of the LCD
screen’s backlight.
BNORMAL
Standard brightness.
Touch 1, then 2.
If the item is not on the screen, touch v/V
to change the page.
BRIGHT
Brightens the LCD screen.
b Notes
How to set
• When you connect your camcorder to outside
power sources, [BRIGHT] is automatically
selected for the setting.
• When you select [BRIGHT], battery life is
slightly reduced during recording.
The default settings are marked with B.
• If you open the LCD panel 180 degrees to face
the screen outside and close the LCD panel to
the camcorder body, the setting becomes
[NORMAL] automatically.
TV TYPE
You need to convert the signal depending
on the TV connected when playing back the
image. The recorded images are played
back as following illustrations.
z Tips
• This adjustment does not affect the recorded
images in any way.
B16:9
LCD COLOR
Select this to view your images on a 16:9
(wide) TV.
You can adjust the color of the LCD screen
16:9 (wide)
images
4:3 images
with
/
.
Low intensity
z Tips
High intensity
• This adjustment does not affect the recorded
images in any way.
4:3
Select this to view your images on a 4:3
standard TV.
16:9 (wide)
images
4:3 images
b Notes
• Aspect ratio of the image recorded with HD
(high definition) image quality is 16:9.
67
CLOCK/ LANG
(Items to set clock and language)
DISP OUTPUT
BLCD PANEL
Shows displays such as the time code on
the LCD screen.
V-OUT/PANEL
Shows displays such as the time code on
the TV screen and the LCD screen.
Touch 1, then 2.
If the item is not on the screen, touch v/V
to change the page.
COMPONENT
How to set
Select [COMPONENT] when connecting
your camcorder to a TV with the
component input jack.
576i
CLOCK SET
Select when connecting your camcorder to
a TV with the component input jack.
B1080i/576i
AREA SET
Select when connecting your camcorder to
a TV that has the component input jack
and is capable of displaying the 1080i
signal.
You can adjust a time difference without
stopping the clock.
Set your local area using v/V when using
your camcorder in other time zones.
Refer to the world time difference on page
88.
SUMMERTIME
You can change this setting without
stopping the clock.
Set to [ON] to move the time forward
1 hour.
LANGUAGE SET
You can select the language to be used on
the LCD screen.
z Tips
• Your camcorder offers [ENG[SIMP]]
(simplified English) for when you cannot find
your native tongue among the options.
68
GENERAL SET
(Other setup items)
A.SHUT OFF (Auto shut
off)
B5 min
The camcorder is automatically turned off
when you do not operate your camcorder
for more than approximately 5 minutes.
Touch 1, then 2.
If the item is not on the screen, touch v/V
to change the page.
NEVER
The camcorder is not automatically turned
off.
How to set
b Notes
• When you connect your camcorder to a wall
socket, [A.SHUT OFF] is automatically set to
[NEVER].
The default settings are marked with B.
REMOTE CTRL (Remote
control)
DEMO MODE
The default setting is [ON], allowing you to
view the demonstration in about 10
minutes, after you slide the POWER switch
The default setting is [ON], allowing you to
use the supplied Remote Commander
to
(Movie).
z Tips
z Tips
• Set to [OFF] to prevent your camcorder from
responding to a command sent by another VCR
remote control unit.
• The demonstration will be suspended in
situations such as those described below.
– When you press START/STOP or PHOTO.
– When you touch the screen during the
demonstration (The demonstration starts
again after about 10 minutes).
– When you remove or insert a “Memory Stick
PRO Duo.”
– When you set the POWER switch to
(Still).
– When you press
IMAGES), or
(HOME),
(Film Roll Index).
(VIEW
REC LAMP (Recording
lamp)
The camera recording lamp on the front of
your camcorder lights up, as the default
setting is [ON].
CALIBRATION
69
Activating functions using the OPTION MENU
The
OPTION MENU appears just like
When the item you want is not on the
screen
Touch another tab. If you cannot find the
item anywhere, the function does not work
under the current situation.
the pop-up window that appears when you
right-click the mouse on a computer.
Various available functions are displayed.
Using the OPTION MENU
b Notes
• The tabs and items that appear on the screen
depend on the recording/playback status of your
camcorder at the time.
1
While using your camcorder,
touch
(OPTION) on the screen.
• Some items appear without a tab.
• The
OPTION MENU cannot be used during
Easy Handycam operation.
(OPTION)
Tab
2
3
Touch the desired item.
If you cannot find the desired item,
touch another tab to change the page.
Change the setting, then touch
.
70
Recording items on the OPTION
MENU
Viewing items on the OPTION
MENU
1
1
Items
*
Page
Items
tab
*
Page
tab
–
–
–
–
–
–
–
–
–
72
72
72
73
73
73
74
75
75
a
–
47
FOCUS
DELETE
SPOT FOCUS
TELE MACRO
EXPOSURE
SPOT METER
SCENE SELECTION
WHITE BAL.
COLOR SLOW SHTR
SUPER NIGHTSHOT
tab
DELETE by date
DELETE ALL
tab
a
a
a
a
a
DIVIDE
ERASE
ERASE ALL
MOVE
-- (The tab depends on the situation/No
tab)
2
a
a
a
a
a
–
38
38
52
52
52
ADD*
–
–
–
75
75
76
FADER
2
ADD*
D.EFFECT
2
ADD by date*
PICT.EFFECT
tab
2
ADD by date*
PRINT
a
a
a
–
76
76
33
33
/
REC SET
SLIDE SHOW
VOLUME
REC MODE
a
a
–
REC MODE
MICREF LEVEL
IMAGE SIZE
QUALITY
DATA CODE
SLIDE SHOW SET
ADD
a
a
–
a
a
a
a
a
–
ADD
SELF-TIMER
TIMING
ADD by date
ADD by date
–
–
RECORD SOUND
/
INDEX SET
*
Items that are included also in the HOME
MENU.
COPIES
–
DATE/TIME
SIZE
–
a
INTERVAL SET
1
2
*
*
Items that are included also in the HOME
MENU.
Items that are included in the HOME MENU
by a different name.
71
Functions set in the OPTION MENU
Items you can set only on the
MENU will be described below.
OPTION
SPOT FOCUS
You can select and adjust the focal point to
aim it at a subject not located at the center
of the screen.
The default settings are marked with B.
FOCUS
You can adjust the focus manually. You can
select this function also when you want to
focus on a certain subject intentionally.
1 Touch the subject on the screen.
9 appears.
1 Touch [MANUAL].
2 Touch [END].
9 appears.
2 Touch
(focusing on close subjects)/
To adjust the focus automatically, touch
[AUTO] t [END] in step 1.
(focusing on distant subjects) to
sharpen the focus.
appears when the
focus cannot be adjusted any closer, and
appears when the focus cannot be adjusted
farther away.
b Notes
• If you set [SPOT FOCUS], [FOCUS] is
automatically set to [MANUAL].
3 Touch
.
To adjust the focus automatically, touch
TELE MACRO
[AUTO] t
in step 1.
This is useful to shoot small subjects, such
as flowers or insects. You can blur out
backgrounds and the subject stands out
clearer.
b Notes
• The minimum possible distance between
camcorder and subject while maintaining sharp
focus is about 1 cm (about 13/32 in.) for wide
angle and about 80 cm (about 2 5/8 feet) for
telephoto.
When you set [TELE MACRO] to [ON]
(
the T (telephoto) side automatically and
allows recording subjects at a close distance
as down to about 45 cm (17 3/4 in.).
z Tips
• It is easier to focus on the subject by moving the
power zoom lever towards T (telephoto) to
adjust the focus, then towards W (wide angle) to
adjust the zoom for recording. When you want
to record a subject at close range, move the
power zoom lever to W (wide angle), then
adjust the focus.
• The focal distance information (distance at
which the subject is focused on, if it is dark and
focus adjustment is difficult) appears for a few
seconds in the following cases (This
To cancel, touch [OFF], or zoom to wide-
angle (W side).
b Notes
• When recording a distant subject, focusing may
be difficult and can take some time.
when it is hard to focus automatically.
information will not display correctly if an
optional conversion lens is being used).
– when the focus mode is switched from
automatic to manual
– when you set focus manually
72
EXPOSURE
SCENE SELECTION
You can fix the brightness of a picture
manually. Adjust the brightness when the
subject is too bright or too dark.
You can record images effectively in
various situations.
BAUTO
Select to automatically record images
effectively without the [SCENE
SELECTION] function.
TWILIGHT* (
)
Select to maintain the darkening
atmosphere of the distant surroundings in
twilight scenes.
1 Touch [MANUAL].
appears.
2 Adjust the exposure by touching
/
.
3 Touch
To return the setting to automatic exposure,
touch [AUTO] t in step 1.
.
TWILIGHT PORT. (
Select to take subject in foreground against
night view.
)
SPOT METER (Flexible
spot meter)
You can adjust and fix the exposure to the
subject, so that it is recorded in suitable
brightness even when there is strong
contrast between the subject and the
background, such as subjects in the
spotlight on stage.
CANDLE ( )
Select to maintain the dim atmosphere of a
candlelit scene.
SUNRISE&SUNSET* (
)
Select to reproduce the atmosphere of
scenes such as sunsets or sunrises.
1 Touch the point where you want to fix and
adjust the exposure on the screen.
FIREWORKS* (
)
appears.
2 Touch [END].
Select to take spectacular shots of
fireworks.
To return the setting to automatic exposure,
touch [AUTO] t [END] in step 1.
LANDSCAPE*(
)
b Notes
Select to shoot distant subjects clearly.
This setting also prevents your camcorder
from focusing on glass or metal mesh in
• If you set [SPOT METER], [EXPOSURE] is
automatically set to [MANUAL].
73
windows that comes in between the
camcorder and the subject.
WHITE BAL. (White
balance)
You can adjust the color balance to the
brightness of the recording environment.
PORTRAIT (Soft portrait) (
)
BAUTO
The white balance is adjusted
automatically.
Select to bring out the subject such as
people or flowers while creating a soft
background.
OUTDOOR (
)
The white balance is adjusted to be
appropriate for the following recording
conditions:
SPOTLIGHT**(
)
– Outdoors
Select to prevent people’s faces from
appearing excessively white when subjects
are lit by strong light.
– Night views, neon signs and fireworks
– Sunrise or sunset
– Under daylight fluorescent lamps
INDOOR (n)
The white balance is adjusted to be
appropriate for the following recording
conditions:
BEACH** (
)
– Indoors
Select to take the vivid blue of the ocean or
a lake.
– At party scenes or studios where the lighting
conditions change quickly
– Under video lamps in a studio, or under
sodium lamps or incandescent-like color
lamps
SNOW** (
Select to take bright pictures of a white
landscape.
)
ONE PUSH (
The white balance will be adjusted
according to the ambient light.
)
1 Touch [ONE PUSH].
2 Frame a white object such as a piece of
paper, to fill the screen under the same
lighting conditions as you will shoot
the subject.
* Adjusted to focus on subjects farther away
only.
3 Touch [
].
** Adjusted not to focus on subjects a short
distance away.
flashes quickly. When the white
balance has been adjusted and stored in
the memory, the indicator stops
flashing.
b Notes
• If you set [SCENE SELECTION], [WHITE
BAL.] setting is canceled.
b Notes
• If you switch to movie recording after shooting
still images with [TWILIGHT PORT.], movies
are recorded with [AUTO].
• Set [WHITE BAL.] to [AUTO] or adjust the
color in [ONE PUSH] under white or cool white
fluorescent lamps.
• When you select [ONE PUSH], keep framing
white objects while
is flashing quickly.
74
•
flashes slowly if [ONE PUSH] could not
be set.
• When [ONE PUSH] was selected, if
flashing after touching
to [AUTO].
b Notes
• Do not use [SUPER NIGHTSHOT] in bright
places. This may cause a malfunction.
• Do not cover the infrared port with your fingers
• Remove the conversion lens (optional).
• Adjust the focus manually ([FOCUS], p. 72)
when it is hard to focus automatically.
keeps
, set [WHITE BAL.]
• If you set [WHITE BAL.], [SCENE
SELECTION] is set to [AUTO].
z Tips
• The shutter speed of your camcorder changes
depending on the brightness, which may result
in a slowdown of the motion of the image.
• If you have changed the battery pack while
[AUTO] was selected, or bring your camcorder
outdoors from inside the house, or vice versa,
select [AUTO] and aim your camcorder at a
nearby white object for about 10 seconds for
better color balance adjustment.
FADER
You can record a transition with the
following effects added to the interval
between scenes.
• When the white balance has been set with [ONE
PUSH], if you change the [SCENE
SELECTION] settings, or bring your camcorder
outdoors from inside the house, or vice versa,
you need to redo the [ONE PUSH] procedure to
readjust the white balance.
1 Select the desired effect during fading in
(in [STBY]) or during fading out (in
[REC]), then touch
.
2 Press START/STOP.
The fader indicator stops flashing and
disappears when the fade is complete.
COLOR SLOW SHTR
(Color Slow Shutter)
When you set [COLOR SLOW SHTR] to
To cancel the fader before starting the
operation, touch [OFF] in step 1.
If you press START/STOP, the setting is
canceled.
[ON],
appears, and you can record an
image brighter in color even in dark places.
b Notes
when it is hard to focus automatically.
• The shutter speed of your camcorder changes
depending on the brightness, which may result
in a slowdown of the motion of the image.
STBY
REC
Fading out
Fading in
WHITE FADER
BLACK FADER
SUPER NIGHTSHOT
The image will be recorded at a maximum
of 16 times the sensitivity of NightShot
recording, if you set [SUPER
NIGHTSHOT] to [ON] while the
ON.
D.EFFECT (Digital effect)
appears on the screen.
When you select [OLD MOVIE],
appears and you can add an old movie
effect to images.
To return to the normal setting, set [SUPER
NIGHTSHOT] to [OFF].
To cancel [D.EFFECT], touch [OFF].
75
z Tips
PICT.EFFECT (Picture
effect)
• You can also operate by pressing PHOTO on
You can add special effects to an image
during recording or playback.
appears.
BOFF
Does not use [PICT.EFFECT] setting.
SEPIA
Images appear in sepia.
B&W (Black and white)
Images appear in black and white.
PASTEL
Images appear as a pale pastel drawing.
MICREF LEVEL (Mic
reference level)
You can select the microphone level for
recording sound.
Select [LOW] when you want to record
exciting and powerful sound in a concert
hall, etc.
BNORMAL
Records surrounding sounds, converting
them into the appropriate level.
LOW (
)
Records surrounding sounds faithfully.
This setting is not suitable for recording
conversations.
SELF-TIMER
A still image is recorded after about 10
seconds.
Press PHOTO when [SELF-TIMER] is set
to [ON], and
appears.
To cancel the count down, touch [RESET].
To cancel the self-timer, select [OFF].
76
Troubleshooting
Troubleshooting
settings, including the clock setting, are
reset).
If you run into any problems using your
camcorder, use the following table to
troubleshoot the problem. If the problem
persists, disconnect the power source and
contact your Sony dealer.
Buttons do not work.
the following buttons/functions are not
available.
– BACK LIGHT button (p. 32)
– To turn on and off the LCD backlight
(Pressing and holding the DISP/BATT
INFO button for a few seconds) (p. 21)
(OPTION) is not displayed.
• The OPTION MENU cannot be used
during Easy Handycam operation.
The menu settings have changed
automatically.
• During Easy Handycam operation, nearly
all the menu items will be automatically set
to the default settings.
• During Easy Handycam operation, some
menu items are fixed as follows.
Overall operations/Easy
Handycam operation/Remote
Commander
– [
– [
– [
REC MODE]: [HD SP]
REC MODE]: [SD SP]
QUALITY]: [FINE]
The power does not turn on.
– [DATA CODE]: [DATE/TIME]
• Attach a charged battery pack to the
• The plug of the AC Adaptor has been
disconnected from the wall socket. Connect
• Following menu items return to the default
settings when you set the POWER switch
to OFF (CHG) for more than 12 hours.
– [FOCUS]
– [SPOT FOCUS]
– [EXPOSURE]
• Set the camcorder onto the Handycam
– [SPOT METER]
– [SCENE SELECTION]
– [WHITE BAL.]
– [MICREF LEVEL]
The camcorder does not operate
even when the power is set to on.
• It takes a few seconds for your camcorder
to be ready to shoot after the power is
turned on. This is not a malfunction.
• Disconnect the AC Adaptor from the wall
socket or remove the battery pack, then
reconnect it after about 1 minute. If the
functions still do not work, press the
object (If you press the RESET button, all
Even if you press EASY, menu
settings do not switch to their
defaults automatically.
• During Easy Handycam operation, settings
for the following menu items are
maintained the ones before Easy Handycam
operation.
– [
/
REC SET]
77
– [WIDE SELECT]
– [X.V.COLOR]
Batteries/Power sources
– [
INDEX SET]
The power abruptly turns off.
– [FILE NO.]
– [
– [
– [
IMAGE SIZE]
INDEX SET]
DISPLAY]
• When approximately 5 minutes have
elapsed while you do not operate your
camcorder, the camcorder is automatically
turned off (A.SHUT OFF). Change the
on the power again, or use the AC Adaptor.
/
– [ INTERVAL SET]
– [VOLUME]
– [BEEP]
– [TV TYPE]
– [COMPONENT]
– [CLOCK SET]
– [AREA SET]
– [SUMMERTIME]
The /CHG (charge) lamp does not
light while the battery pack is being
charged.
– [
LANGUAGE SET]
– [DEMO MODE]
– [TIMING] and [RECORD SOUND] in
[SMTH SLW REC]
• Slide the POWER switch to OFF (CHG)
(p. 16).
• Attach the battery pack to the camcorder
Your camcorder gets warm.
• Connect the mains lead to the wall socket
properly.
• Set the camcorder onto the Handycam
• This is because the power has been turned
on for a long time. This is not a
malfunction.
The supplied Remote Commander
does not function.
The /CHG (charge) lamp flashes
while the battery pack is being
charged.
• Set [REMOTE CTRL] to [ON] (p. 69).
• Insert a battery into the battery holder with
the +/– polarities correctly matching the +/–
• Remove any obstructions between the
Remote Commander and the remote sensor.
• Point the remote sensor away from strong
light sources such as direct sunlight or
overhead lighting. Otherwise, the Remote
Commander may not function properly.
• Attach the battery pack to the camcorder
disconnect the AC Adaptor from the wall
socket and contact your Sony dealer. The
battery pack may be damaged.
The remaining battery time indicator
does not indicate the correct time.
• The ambient temperature is too high or too
low. This is not a malfunction.
• The battery pack has not been charged
enough. Fully charge the battery again. If
the problem persists, replace the battery
Another DVD device malfunctions
when you use the supplied Remote
Commander.
• Select a commander mode other than DVD
2 for your DVD device, or cover the sensor
of your DVD device with black paper.
• The indicated time may not be correct
depending on the environment of use.
78
The battery pack is quickly
discharged.
The data file name is not indicated
correctly or flashes.
• The ambient temperature is too high or low.
This is not a malfunction.
• Fully charge the battery again. If the
problem persists, replace the battery pack
• The file is damaged.
• The file format is not supported by your
Recording
Refer also to “Memory Stick PRO Duo” (p.
LCD screen
Menu items are grayed out.
• You cannot select grayed items in the
current recording/playback situation.
• There are some functions you cannot
Pressing START/STOP or PHOTO
does not record images.
• The playback screen is displayed. Set the
POWER switch to
(Movie) or
The buttons do not appear on the
touch panel.
• Your camcorder is recording the image you
have just shot on the “Memory Stick PRO
Duo.” You cannot make new recording
during this period.
• The “Memory Stick PRO Duo” is full. Use
a new “Memory Stick PRO Duo” or format
• Touch the LCD screen lightly.
• Press DISP/BATT INFO on your
camcorder (or DISPLAY on the Remote
The buttons on the touch panel do
not work correctly or do not work at
all.
• Total number of movie scenes or still
images exceeds the recordable capacity of
• Adjust the touch panel ([CALIBRATION],
p. 94).
You cannot record a still image.
“Memory Stick PRO Duo”
• The playback screen is displayed. Set your
• You can capture up to 3 still images only
during movie recording.
You cannot operate functions using
the “Memory Stick PRO Duo.”
• If you use a “Memory Stick PRO Duo”
formatted on a computer, format it again on
• The “Memory Stick PRO Duo” has run out
of space. Use a new “Memory Stick PRO
Duo” or format the “Memory Stick PRO
• You cannot record a still image together
with:
– [SMTH SLW REC]
– [FADER]
You cannot delete images stored on
or format the “Memory Stick PRO
Duo.”
• The maximum number of images that you
can delete at one time is 100.
– [D.EFFECT]
• You cannot delete the images protected on
another device.
– [PICT.EFFECT]
79
point that recording movie starts/stops.
This is not a malfunction.
The access lamp remains lit or
flashing even when you stop
recording.
The movie aspect ratio (16:9 (wide)/
4:3) cannot be changed.
• Your camcorder is recording the scene you
have just shot on the “Memory Stick PRO
Duo.”
• The aspect ratio of the movie recorded with
HD (high definition) image quality is 16:9
(wide).
The imaging field looks different.
• The imaging field may look different
depending on the condition of your
camcorder. This is not a malfunction.
The auto focus does not function.
• Set [FOCUS] to [AUTO] (p. 72).
• The recording conditions are not suitable
for auto focus. Adjust the focus manually
(p. 72).
The flash does not work.
• You cannot record with the flash with:
– Capturing still images while shooting a
movie
[STEADYSHOT] does not function.
– If a conversion lens (optional) is attached
• Set [STEADYSHOT] to [ON] (p. 61).
• Even if auto flash or
reduction) is selected, you cannot use the
internal flash with:
(Auto redeye
• [STEADYSHOT] may not be able to
compensate for excessive vibrations.
– NightShot
The BACK LIGHT function does not
function.
– [SUPER NIGHTSHOT]
– [TWILIGHT], [CANDLE],
[SUNRISE&SUNSET], [FIREWORKS],
[LANDSCAPE], [SPOTLIGHT],
[BEACH] or [SNOW] in [SCENE
SELECTION]
• The BACK LIGHT function cannot be used
during Easy Handycam operation.
The subjects passing by the lens
very fast appear crooked.
– [MANUAL] in [EXPOSURE]
– [SPOT METER]
• This is called the focal plane phenomenon.
This is not a malfunction. Because of the
way the image device (CMOS sensor) reads
out image signals, the subjects passing by
the lens rapidly might appear crooked
depending on the recording conditions.
The actual recording time for movie
is less than the expected
approximate recording time of the
“Memory Stick PRO Duo.”
• Depending on an object, such as a fast
moving object, the time available for
Tiny spots in white, red, blue, or
green appear on the screen.
• The spots appear when you are recording
with [SUPER NIGHTSHOT] or [COLOR
SLOW SHTR]. This is not a malfunction.
There is a time difference between
the point where you press START/
STOP and the point that the
recorded movie starts/stops.
The color of the image is not
correctly displayed.
• On your camcorder, there may be a slight
time difference between the point where
you press START/STOP and the actual
• Set the NIGHTSHOT switch to OFF
(p. 32).
80
in the case of still images.) This is not a
• Images recorded on other devices may not
be played back. This is not a malfunction
The screen image is bright, and the
subject does not appear on the
screen.
• Set the NIGHTSHOT switch to OFF
(p. 32).
“
” is indicated on an image in the
The screen image is dark, and the
subject does not appear on the
screen.
VISUAL INDEX screen.
• This may appear on still images recorded
on other devices, edited on a computer, etc.
• Press and hold DISP/BATT INFO for a few
• You removed the AC Adaptor or the
battery pack before the access lamp is
turned off after recording. This may
damage your image data and
displayed.
is
Horizontal stripes appear on the
images.
• This occurs when recording images under a
fluorescent lamp, sodium lamp, or mercury
lamp. This is not a malfunction.
“
” is indicated on an image in the
VISUAL INDEX screen.
still appears, delete the image marked with
(p. 46).
[SUPER NIGHTSHOT] cannot be
operated.
• Set the NIGHTSHOT switch to ON (p. 32).
No sound or only a quiet sound is
heard during playback.
[COLOR SLOW SHTR] does not
operate correctly.
• Sound is not output when the LCD screen is
closed. Open the LCD screen.
• When you record sound with [MICREF
sound may be difficult to hear.
• [COLOR SLOW SHTR] may not operate
correctly in total darkness. Use NightShot
or [SUPER NIGHTSHOT].
• When using [SMTH SLW REC], set
[RECORD SOUND] to [ON] (p. 33).
You cannot adjust [LCD BL LEVEL].
• You cannot adjust [LCD BL LEVEL]
when:
– The LCD panel is closed on your
camcorder with the LCD screen facing
out.
Editing images on your
camcorder
– The power is supplied from the AC
Adaptor.
Unable to edit.
• Unable to edit because of the condition of
the image.
Playing back images on your
camcorder
Images cannot be added in the
Playlist.
Images cannot be played back.
• There is no free space in the “Memory
Stick PRO Duo.”
• Images cannot be played back if you have
modified files or folders, or have edited the
data on a computer. (The file name flashes
81
• You can add no more than 999 images with
HD (high definition) image quality, or 99
images with SD (standard definition) image
quality, to a Playlist. Erase unnecessary
play back the image.
Black bands appear at the top and
bottom of the screen of the 4:3 TV.
• You cannot add still images in the Playlist.
• This happens when viewing an image
recorded in the 16:9 (wide) mode on a 4:3
TV. This is not a malfunction.
A movie cannot be divided.
• A movie that is too short cannot be divided.
• A movie protected on another device
cannot be divided.
Playing the “Memory Stick PRO
Duo” on other devices
The device does not play or read the
“Memory Stick PRO Duo.”
Unable to copy the movies being
played to a “Memory Stick PRO
Duo.”
• You can play back the images with HD
(high definition) image quality only on
devices that comply with AVCHD-format.
• For details on the AVCHD-format-
compliant devices, see “Read This First”
(the separate paper volume), or the
following URL.
• You cannot copy a movie to a “Memory
Stick PRO Duo” as a still image during
playback on your camcorder.
• Use the supplied “Picture Motion
Browser.” For details, see “Picture Motion
Browser Guide” on the supplied CD-ROM.
http://www.sony.net/
Viewing on the TV
Dubbing/Connecting to other
devices
You cannot view the image or hear
the sound on the TV.
You cannot dub correctly.
• When you are using the component video
cable, set [COMPONENT] according to the
requirements of the connected device
• When you are using the component video
cable, make sure the red and white plugs of
the A/V connecting cable are connected
• Images are not output from the HDMI OUT
jack, if copyright protection signals are
recorded in the images.
• When you are using the S VIDEO plug,
make sure the red and white plugs of the A/
• You cannot dub images using an HDMI
cable.
• The A/V connecting cable is not connected
properly. Make sure to connect to the input
Functions that cannot be used
simultaneously
The following list shows examples of
unworkable combinations of functions and
menu items.
Because of following
Cannot use
settings
The image appears distorted on the
4:3 TV.
BACK LIGHT
[SPOT METER],
[FIREWORKS],
[MANUAL] in
[EXPOSURE]
• This happens when viewing an image
recorded in the 16:9 (wide) mode on a 4:3
82
Because of following
settings
Cannot use
[SCENE
SELECTION]
NightShot, [SUPER
NIGHTSHOT],
[COLOR SLOW
SHTR], [OLD
MOVIE], [TELE
MACRO], [FADER]
[SPOT METER] NightShot, [SUPER
NIGHTSHOT]
[EXPOSURE]
NightShot, [SUPER
NIGHTSHOT]
[WHITE BAL.]
NightShot, [SUPER
NIGHTSHOT]
[ONE PUSH] in
[WHITE BAL.]
[SMTH SLW REC]
[SPOT FOCUS]
[SCENE SELECTION]
[FADER], [D.EFFECT]
[SUPER
NIGHTSHOT]
[COLOR SLOW [FADER],
SHTR]
[D.EFFECT], [SCENE
SELECTION]
[FADER]
[SUPER
NIGHTSHOT],
[COLOR SLOW
SHTR], [D.EFFECT],
[CANDLE],
[FIREWORKS]
[D.EFFECT]
[SUPER
NIGHTSHOT],
[COLOR SLOW
SHTR], [FADER]
[OLD MOVIE]
[SCENESELECTION],
[PICT.EFFECT]
[PICT.EFFECT] [OLD MOVIE]
[TELE MACRO] [SCENE SELECTION]
[AUTO SLW
SHUTTR]
[SMTH SLW REC],
[D.EFFECT], [SCENE
SELECTION],
[COLOR SLOW
SHTR], [SUPER
NIGHTSHOT]
[WIDE SELECT] [OLD MOVIE]
83
Troubleshooting
Warning indicators and messages
Self-diagnosis display/Warning
indicators
E (Battery level warning)
Slow flashing
• The battery pack is nearly used up.
• Depending on the operating
environment or battery conditions, E
may flash, even if there are
If indicators appear on the LCD screen,
check the following.
You can fix some symptoms by yourself. If
theproblempersistseven afteryouhavetried
a couple of times, contact your Sony dealer
or local authorized Sony service facility.
approximately 20 minutes remaining.
(Warning indicator pertaining to
“Memory Stick PRO Duo”)
C:04:00
Slow flashing
• Free space for recording images are
running out. For the type of “Memory
Stick” you can use with your
• No “Memory Stick PRO Duo” is
C:(or E:) ss:ss (Self-diagnosis
display)
Fast flashing
C:04:ss
• There are not enough free space for
recording images. Delete unnecessary
images, or format the “Memory Stick
PRO Duo” after storing the images on
• The battery pack is not an
“InfoLITHIUM” battery pack (H
series). Use an “InfoLITHIUM” battery
• Connect the DC plug of the AC
Adaptor to the DC IN jack of the
Handycam Station or your camcorder
• The Image Database File is damaged
(Warning indicators pertaining to
“Memory Stick PRO Duo”
formatting)*
C:13:ss / C:32:ss
• Remove the power source. Reconnect it
and operate your camcorder again.
• The “Memory Stick PRO Duo” is
damaged.
• The “Memory Stick PRO Duo” is not
E:20:ss / E:31:ss / E:61:ss /
E:62:ss / E:91:ss / E:94:ss
• A malfunction that you cannot service
has occurred. Contact your Sony dealer
or local authorized Sony service
facility. Inform them of the 5-digit
code, which starts from “E”.
(Warning indicator pertaining to
incompatible “Memory Stick PRO
Duo”)*
• An incompatible “Memory Stick PRO
101-0001 (Warning indicator
pertaining to files)
Slow flashing
• The file is damaged.
• The file is unreadable.
- (Warning indicator pertaining
to the write-protect of the “Memory
Stick PRO Duo”)*
84
• Access to the “Memory Stick PRO
Duo” was restricted on another device.
This Memory Stick is not
formatted correctly.
• Check the format, then format the
“Memory Stick PRO Duo” with your
(Warning indicator pertaining to
the Memory Stick Duo cover)
Slow flashing
• The Memory Stick Duo cover is open
Memory Stick folders are full.
• You cannot create folders exceeding
999MSDCF. You cannot create or
delete folders using your camcorder.
• Format the “Memory Stick PRO Duo”
using your computer.
(Warning indicator pertaining to
the flash)
Fast flashing*
• There is something wrong with the
flash.
This Memory Stick may not be able
to record or play movies.
(Warning indicator pertaining to
camera-shake warning)
• Use the recommended “Memory Stick”
(p. 11).
• The amount of lights is not sufficient,
so camera-shake easily occurs. Use the
flash.
• The camcorder is unsteady, so camera-
shake easily occurs. Hold the
camcorder steady with both hands and
record the image. However, note that
the camera-shake warning indicator
does not disappear.
This Memory Stick may not be able
to record or play images correctly.
• Contact your Sony dealer or local
authorized Sony service facility.
Do not eject the Memory Stick during
writing. Data may be damaged.
• Insert the “Memory Stick PRO Duo”
again, and follow the instructions on
the screen.
* You hear a melody when the warning indicators
Description of warning
messages
The Image Database File is
damaged. Do you want to create a
new file?
If messages appear on the screen, follow the
instructions.
HD movie management information
is damaged. Create new
information?
x “Memory Stick PRO Duo”
• The image management file is
damaged. When you touch [YES], a
new image management file is created.
The old recorded images on the
“Memory Stick PRO Duo” cannot be
played back (Image files are not
damaged). If you perform [REPAIR
IMG.DB F.] after creating new
Reinsert the Memory Stick.
• Reinsert the “Memory Stick PRO Duo”
a few times. If even then the indicator
flashes, the “Memory Stick PRO Duo”
could be damaged. Try with another
“Memory Stick PRO Duo.”
85
information, playing back the old
x Other
recorded images may become possible.
If it does not work, copy the image to a
computer using the supplied software.
No further selection is possible.
• You can select only 100 images at one
time for:
– deleting images
– editing the playlist of HD (high
definition) movies
Inconsistencies found in Image
Database File. Movies cannot be
recorded or played. Do you want to
repair the Image Database File?
– printing still images
Inconsistencies found in Image
Database File. Cannot record or play
HD movies. Do you want to repair the
Image Database File?
Data protected.
• You tried to delete data protected on
another device. Release the protection
of the data on the device used to protect
the data.
• The Image Database File is damaged.
Touch [YES] to repair.
Recovering data
• Your camcorder tries to recover data
automatically if the data writing was
not performed properly.
Cannot recover data.
• Because data writing onto the
“Memory Stick PRO Duo” failed, your
camcorder tried to recover the data, but
could not recover data. You may not be
able to record or edit data on the
“Memory Stick PRO Duo.”
x PictBridge compliant printer
Not connected to PictBridge
compatible printer.
• Turn off the printer and on again, then
remove the USB cable (supplied) and
reconnect it.
Cannot print. Check the printer.
• Turn off the printer and on again, then
remove the USB cable (supplied) and
reconnect it.
86
Additional Information
Using your camcorder abroad
Power supply
On TV color systems
You can use your camcorder in any
countries/regions using the AC Adaptor
supplied with your camcorder within the
AC 100 V to 240 V, 50/60 Hz range.
Your camcorder is a PAL-system-based
camcorder. If you want to view the
playback image on a TV, it must be a PAL-
system-based TV with an AUDIO/VIDEO
input jack.
Viewing images recorded with HD
(high definition) image quality
System
Used in
Australia, Austria, Belgium,
China, Czech Republic,
In countries/regions where 1080/50i is
supported, you can view the images with
the same HD (high definition) image
quality as that of the recorded images. You
need a PAL-system-based and 1080/50i
compatible TV (or monitor) with
component and AUDIO/VIDEO input
jacks. Both a component video cable and an
A/V connecting cable must be connected.
Denmark, Finland, Germany,
Holland, Hong Kong, Hungary,
Italy, Kuwait, Malaysia, New
Zealand, Norway, Poland,
Portugal, Singapore, Slovak
Republic, Spain, Sweden,
Switzerland, Thailand, United
Kingdom, etc.
PAL
Viewing images recorded with SD
(standard definition) image quality
PAL - M Brazil
PAL - N Argentina, Paraguay, Uruguay.
To view images recorded with SD (standard
definition) image quality, you need a PAL-
system-based TV with AUDIO/VIDEO
input jacks. An A/V connecting cable must
be connected.
Bahama Islands, Bolivia,
Canada, Central America,
Chile, Colombia, Ecuador,
Guyana, Jamaica, Japan, Korea,
Mexico, Peru, Surinam,
NTSC
Taiwan, the Philippines, the
U.S.A., Venezuela, etc.
Bulgaria, France, Guiana, Iran,
SECAM Iraq, Monaco, Russia, Ukraine,
etc.
87
Setting to the local time
You can easily set the clock to the local time by setting a time difference when using your
camcorder abroad. Touch
(HOME) t
(SETTINGS) t [CLOCK/ LANG] t
World time difference
Time-zone
Area setting
differences
Time-zone
Area setting
differences
+11:00
+12:00
–12:00
–11:00
–10:00
–09:00
–08:00
–07:00
–06:00
–05:00
–04:00
–03:30
–03:00
–02:00
–01:00
Solomon Is.
GMT
Lisbon, London
Berlin, Paris
Fiji, Wellington
Eniwetok, Kwajalein
Midway Is., Samoa
Hawaii
+01:00
+02:00
+03:00
+03:30
+04:00
+04:30
+05:00
+05:30
+06:00
+06:30
+07:00
+08:00
+09:00
+09:30
+10:00
Helsinki, Cairo, Istanbul
Moscow, Nairobi
Tehran
Alaska
Abu Dhabi, Baku
Kabul
LosAngeles, Tijuana
Denver, Arizona
Chicago, Mexico City
NewYork, Bogota
Santiago
Karachi, Islamabad
Calcutta, New Delhi
Almaty, Dhaka
Rangoon
St. John’s
Bangkok, Jakarta
HongKong, Singapore, Beijing
Seoul, Tokyo
Brasilia, Montevideo
Fernando de Noronha
Azores, Cape Verde Is.
Adelaide, Darwin
Melbourne, Sydney
88
Files/folder structure on the “Memory Stick
PRO Duo”
The file/folder structure is shown below. You do not usually need to acknowledge the file/
folder structure, when recording/playing back images on the camcorder. To enjoy still images
or movies by connecting to a computer, see “Picture Motion Browser Guide” on the supplied
CD-ROM, then use the supplied application.
A Image management files
When you delete the files, you cannot
record/play back the images correctly.
The files are defaulted as hidden files
and not usually displayed.
9999, another folder is created to store
new image files.
The folder name goes up: [101MSDCF]
t [102MSDCF]
• By selecting [
COMPUTER] on [USB
Stick PRO Duo” in the camcorder from a
computer through USB connection.
B HD movie management
information folder
This folder contains recording data of
movies with HD (high definition) image
quality. Do not try to open this folder or
access the contents of this folder from a
computer. Doing so might damage
image files, or prevent image files from
being played back.
• Do not modify the files or folders on a “Memory
Stick PRO Duo” in the camcorder from a
computer. The image files may be destroyed or
may not be played back.
• We (Sony) will not be responsible for the results
of operating the data on a “Memory Stick PRO
Duo” in the camcorder from a computer.
• When you delete image files, follow the steps on
page 46. Do not delete the image files on a
“Memory Stick PRO Duo” in the camcorder
directly from a computer.
• Do not format a “Memory Stick PRO Duo” in
the camcorder using a computer. The camcorder
may not operate correctly.
C SD movie files (MPEG2 files)
The extension of the files is “.MPG”.
The maximum size is 2 GB. When the
capacity of a file exceeds 2 GB, the file
becomes divided.
The file numbers go up automatically.
When the capacity of a file number
exceeds 9999, another folder is created
to record new movie files.
• Do not copy the files on a “Memory Stick PRO
Duo” in the camcorder from a computer. We
(Sony) will not be responsible for the results of
this kind of operation.
The folder name goes up: [101PNV01]
t [102PNV01]
D Still image files (JPEG files)
The extension of the files is “.JPG”. The
file numbers go up automatically. When
the capacity of a file number exceeds
89
Maintenance and precautions
A high definition specification which utilizes
1,080 effective scanning lines and the interlace
system.
About the AVCHD format
Your digital video camera recorder
incorporates both the AVCHD format and
the MPEG2 format for the recording
function.
*2: 720p specification
A high definition specification which utilizes 720
effective scanning lines and the progressive
system.
*3: Data recorded in AVCHD format other than
the above mentioned cannot be played on your
camcorder.
What is the AVCHD format?
The AVCHD format is a high definition
digital video camera format used to record
an HD (high definition) signal of either the
About the “Memory Stick”
1
1080i specification* or the 720p
2
A “Memory Stick” is a compact, portable
IC recording medium with a large data
capacity.
You can use only a “Memory Stick Duo,”
which is about the half size of a standard
“Memory Stick,” with your camcorder.
However, we do not guarantee the
operation of all types of “Memory Stick
Duo” on your camcorder. (See the list
below for more details.)
specification* , using efficient data
compression coding technology. The
MPEG-4 AVC/H.264 format is adopted to
compress video data, and the Dolby Digital
or Linear PCM system is used to compress
audio data.
The MPEG-4 AVC/H.264 format is capable
of compressing images at higher efficiency
than that of the conventional image
compressing format. The MPEG-4 AVC/
H.264 format enables a high definition
video signal shot on a digital video camera
recorder to be recorded on 8 cm DVD discs,
internal hard disk drive, flash memory, etc.
Recording/
Types of “Memory Stick”
Playback
“Memory Stick Duo”
(without MagicGate)
-
1
1
“Memory Stick PRO Duo”
a*
Recording and playback on your
camcorder
“Memory Stick PRO-HG Duo”
a*
*1 The types of “Memory Stick” that support high
speed data transfer. The speed of data transfer
varies depending on the device to be used.
Based on the AVCHD format, your
camcorder records with the HD (high
definition) image quality mentioned below.
In addition to HD (high definition) image
quality, your camcorder is capable of
recording an SD (standard definition) signal
in the conventional MPEG2 format.
• This product is not compatible with 8-bit
pararell data transfer.
• This product cannot record or play data that uses
“MagicGate” technology. “MagicGate” is a
copyright protection technology that records and
transfers the contents in an encrypted format.
Video signal:
AVCHD format 1440 × 1080/50i*
Audio signal:
• This product is compatible with “Memory Stick
Micro” (“M2”). “M2” is the abbreviation for the
“Memory Stick Micro.”
3
• Still image format: Your camcorder compresses
and records image data in the JPEG (Joint
Photographic Experts Group) format. The file
extension is “.JPG.”
Dolby Digital 5.1 ch
Recording media:
“Memory Stick PRO Duo”
• File names of still images:
– 101- 0001: This file name appears on the
screen of your camcorder.
*1: 1080i specification
90
– DSC00001.JPG: This file name appears on
the display of a computer.
• A “Memory Stick PRO Duo” formatted by a
computer (Windows OS/Mac OS) does not have
guaranteed compatibility with your camcorder.
• Data read/write speed may vary depending on
the combination of the “Memory Stick PRO
Duo” and the “Memory Stick PRO Duo”
compliant product you use.
• Do not insert anything other than a “Memory
Stick PRO Duo” into the Memory Stick Duo
slot. Doing so may cause a malfunction.
x On a location for use
Do not use or keep the “Memory Stick PRO
Duo” in the following locations:
• Places subject to extremely high temperature,
such as a car parked outside in the summer.
• Places under direct sunlight.
Notes on use
Damaged or lost data may occur in the
following cases (the data will not be
compensated for):
• If you eject the “Memory Stick PRO Duo,” or
turn off your camcorder while your camcorder is
reading or writing image files on the “Memory
Stick PRO Duo” (while the access lamp is lit or
flashing).
• Places with extremely high humidity or subject
to corrosive gases.
x On the Memory Stick Duo adaptor
After inserting a “Memory Stick PRO Duo”
into the Memory Stick Duo adaptor, you
can use it with a standard “Memory Stick”
compliant device.
• When using a “Memory Stick PRO Duo” with a
“Memory Stick” compliant device, be sure to
insert the “Memory Stick PRO Duo” into a
Memory Stick Duo adaptor.
• If you use the “Memory Stick PRO Duo” near
magnets or magnetic fields.
• When inserting a “Memory Stick PRO Duo”
into a Memory Stick Duo adaptor, make sure the
“Memory Stick PRO Duo” is inserted facing in
the correct direction, then insert it all the way in.
Note that improper use may cause a
malfunction. Also, if you force the “Memory
Stick PRO Duo” into the Memory Stick Duo
adaptor in the wrong direction, it may be
damaged.
It is recommended you make a back-up of
important data on the hard disk of a
computer.
x On handling a “Memory Stick PRO
Duo”
Keep the following in mind when handling
a “Memory Stick PRO Duo.”
• Do not insert a Memory Stick Duo adaptor
without a “Memory Stick PRO Duo” attached
into a “Memory Stick” compliant device. Doing
so may result in malfunctions of the device.
• Be careful not to apply excessive force when
writing on a memo area on a “Memory Stick
PRO Duo.”
• Do not attach a label or the like on a “Memory
Stick PRO Duo” or a Memory Stick Duo
adaptor.
• When you carry or store a “Memory Stick PRO
Duo,” put it in its case.
• Do not touch, or allow metallic objects to come
into contact with the terminals.
x On a “Memory Stick PRO Duo”
The maximum memory capacity of a
“Memory Stick PRO Duo” or “Memory
Stick PRO-HG Duo” that can be used with
your camcorder is 8 GB.
• Do not bend, drop or apply strong force to the
“Memory Stick PRO Duo.”
Notes on using “Memory Stick Micro”
• Do not disassemble or modify the “Memory
Stick PRO Duo.”
• Do not let the “Memory Stick PRO Duo” get
wet.
• Keep “Memory Stick PRO Duo” media out of
the reach of small children. There is danger that
a child might swallow it.
• To use a “Memory Stick Micro” with your
camcorder, you need a Duo-sized M2 Adaptor.
Insert the “Memory Stick Micro” into the Duo-
sized M2 Adaptor, and then insert the adaptor
into the “Memory Stick Duo” slot. If you insert
a “Memory Stick Micro” into your camcorder
without using a Duo-sized M2 Adaptor, you
might not be able to remove it from your
camcorder.
91
• Do not leave the “Memory Stick Micro” within
the reach of small children. They might
accidentally swallow it.
With an AC Adaptor/charger, the remaining
battery time and charging time appear.
To charge the battery pack
• Be sure to charge the battery pack before you
start using your camcorder.
• We recommend charging the battery pack in an
ambient temperature of between 10 °C to 30 °C
(50 °F to 86 °F) until the /CHG (charge) lamp
turns off. If you charge the battery pack outside
of this temperature range, you may not be able
to charge it efficiently.
On image data compatibility
• Image data files recorded on a “Memory Stick
PRO Duo” by your camcorder conform to the
“Design rule for Camera File system” universal
standard established by the JEITA (Japan
Electronics and Information Technology
Industries Association).
• On your camcorder, you cannot play back still
images recorded on other devices (DCR-
TRV900E or DSC-D700/D770) that do not
conform to the universal standard. (These
models are not sold in some regions.)
• If you cannot use a “Memory Stick PRO Duo”
that has been used with another device, format it
formatting erases all information on the
“Memory Stick PRO Duo.”
To use the battery pack effectively
• Battery pack performance decreases when the
ambient temperature is 10 °C (50 °F) or below,
and the length of time you can use the battery
pack becomes shorter. In that case, do one of the
following to use the battery pack for a longer
time.
– Put the battery pack in a pocket to warm it up,
and insert it in your camcorder right before
you start taking shots.
– Use a large capacity battery pack: NP-FH70/
FH100 (optional).
• Frequent use of the LCD screen or a frequent
playback, fast forward or rewind operation
wears out the battery pack faster.
• You may not be able to play back images with
your camcorder:
– When playing back image data modified on
your computer.
– When playing back image data recorded with
other devices.
About the “InfoLITHIUM”
battery pack
We recommend using a large capacity battery
pack: NP-FH70/FH100 (optional).
• Be sure to set the POWER switch to OFF
(CHG) when not recording or playing back on
your camcorder. The battery pack is also
consumed when your camcorder is in recording
standby or playback pause.
• Have spare battery packs ready for 2 or 3 times
the expected recording time, and make trial
recordings before making the actual recording.
Your camcorder operates only with an
“InfoLITHIUM” battery pack (H series).
“InfoLITHIUM” H series battery packs
have the
mark.
What is an “InfoLITHIUM” battery
pack?
An “InfoLITHIUM” battery pack is a
lithium-ion battery pack that has functions
for communicating information related to
operating conditions between your
camcorder and an optional AC Adaptor/
charger.
The “InfoLITHIUM” battery pack
calculates the power consumption
according to the operating conditions of
your camcorder, and displays the remaining
battery time in minutes.
• Do not expose the battery pack to water. The
battery pack is not water resistant.
About the remaining battery time
indicator
• When the power goes off even though the
remaining battery time indicator indicates that
the battery pack has enough power to operate,
charge the battery pack fully again. Remaining
battery time will be indicated correctly. Note,
however, that the battery indication will not be
restored if it is used in high temperatures for a
long time, or if left in a fully charged state, or
92
when the battery pack is frequently used. Use
the remaining battery time indication as a rough
guide only.
• The E mark that indicates low battery flashes
even if there are still 5 to 10 minutes of battery
time remaining, depending on the operating
conditions or ambient temperature.
sun. They may malfunction or become
deformed.
– Near strong magnetic fields or mechanical
vibration. The camcorder may malfunction.
– Near strong radio waves or radiation. The
camcorder may not be able to record properly.
– Near AM receivers and video equipment.
Noise may occur.
– On a sandy beach or anywhere dusty. If sand
or dust gets in your camcorder, it may
malfunction. Sometimes this malfunction
cannot be repaired.
– Near windows or outdoors, where the LCD
screen or the lens may be exposed to direct
sunlight. This damages inside the LCD
screen.
About storage of the battery pack
• If the battery pack is not used for a long time,
fully charge the battery pack and use it up on
your camcorder once a year to maintain proper
function. To store the battery pack, remove it
from your camcorder and put it in a dry, cool
place.
• To discharge the battery pack on your
camcorder completely, touch
(HOME) t
• Operate your camcorder on DC 6.8 V/7.2 V
(battery pack) or DC 8.4 V (AC Adaptor).
• For DC or AC operation, use the accessories
recommended in these operating instructions.
• Do not let your camcorder get wet, for example,
from rain or sea water. If your camcorder gets
wet, it may malfunction. Sometimes this
malfunction cannot be repaired.
• If any solid object or liquid gets inside the
casing, unplug your camcorder and have it
checked by a Sony dealer before operating it
any further.
(SETTINGS) t [GENERAL SET] t
[A.SHUT OFF] t [NEVER] and leave your
camcorder in recording standby until the power
About battery life
• Battery capacity decreases over time and
through repeated use. If decreased usage time
between charges becomes significant, it is
probably time to replace it with a new one.
• Each battery’s life is governed by storage,
operating and environmental conditions.
• Avoid rough handling, disassembling,
modifying, physical shock, or impact such as
hammering, dropping or stepping on the
product. Be particularly careful of the lens.
About x.v.Color
• Keep the POWER switch setting to OFF (CHG)
when you are not using your camcorder.
• Do not wrap your camcorder with a towel, for
example, and operate it. Doing so might cause
heat to build up inside.
• When disconnecting the mains lead, pull it by
the plug and not the lead.
• Do not damage the mains lead such as by
placing anything heavy on it.
• x.v.Color is a more familiar term for the xvYCC
standard proposed by Sony, and is a trademark
of Sony.
• xvYCC is an international standard for color
space in video. This standard can express a
wider color range than the currently used
broadcast standard.
About handling of your
camcorder
• Keep metal contacts clean.
• Keep the Remote Commander and button-type
battery out of children’s reach. If the battery is
accidentally swallowed, consult a doctor
immediately.
On use and care
• Do not use or store the camcorder and
accessories in the following locations:
• If the battery electrolytic liquid has leaked:
– consult your local authorized Sony service
facility.
– wash off any liquid that may have contacted
your skin.
– Anywhere extremely hot, cold or humid.
Never leave them exposed to temperatures
above 60 °C (140 °F), such as under direct
sunlight, near heaters or in a car parked in the
93
– if any liquid gets in your eyes, wash with
plenty of water and consult a doctor.
• If your camcorder is used in a cold place, a
residual image may appear on the LCD screen.
This is not a malfunction.
• While using your camcorder, the back of the
LCD screen may heat up. This is not a
malfunction.
x When not using your camcorder for a
long time
• Periodically turn it on and let it run such as by
playing back or recording images for about 3
minutes.
x To clean the LCD screen
If fingerprints or dust make the LCD screen
dirty, it is recommended you use a soft
cloth to clean it. When you use the LCD
Cleaning Kit (optional), do not apply the
cleaning liquid directly to the LCD screen.
Use cleaning paper moistened with the
liquid.
• Use up the battery pack completely before
storing it.
Moisture condensation
If your camcorder is brought directly from a
cold place to a warm place, moisture may
condense inside your camcorder. This may
cause a malfunction to your camcorder.
x On adjustment of the touch panel
(CALIBRATION)
x If moisture condensation has occurred
Leave your camcorder for about 1 hour
without turning it on.
The buttons on the touch panel may not
work correctly. If this happens, follow the
procedure below. It is recommended that
you connect your camcorder to the wall
socket using the supplied AC Adaptor
during the operation.
x Note on moisture condensation
Moisture may condense when you bring
your camcorder from a cold place into a
warm place (or vice versa) or when you use
your camcorder in a humid place as
follows:
1 Turn on your camcorder.
2 Touch
t [GENERAL SET] t
[CALIBRATION].
(HOME) t
(SETTINGS)
• You bring your camcorder from a ski slope into
a place warmed up by a heating device.
• You bring your camcorder from an air
conditioned car or room into a hot place outside.
• You use your camcorder after a squall or a
shower.
• You use your camcorder in a hot and humid
place.
3 Touch “×” displayed on the screen with the
corner of the “Memory Stick PRO Duo” or
the like 3 times.
x How to prevent moisture condensation
When you bring your camcorder from a
cold place into a warm place, put your
camcorder in a plastic bag and seal it
tightly. Remove the bag when the air
temperature inside the plastic bag has
reached the ambient temperature (after
about 1 hour).
Touch [CANCEL] to cancel.
If you did not press the right spot, try the
calibration again.
b Notes
• Do not use a sharp-pointed object for
calibration. Doing so may damage the LCD
screen.
• You cannot calibrate the LCD screen if it is
rotated, or closed with the screen facing out.
LCD screen
• Do not exert excessive pressure on the LCD
screen, as it may cause damage.
94
x Procedures
On handling the casing
Connect your camcorder to a wall socket
using the supplied AC Adaptor, and leave it
with the POWER switch set to OFF (CHG)
for more than 24 hours.
• If the casing is soiled, clean the camcorder body
with a soft cloth lightly moistened with water,
and then wipe the casing with a dry soft cloth.
• Avoid the following to avoid damage to the
finish:
– Using chemicals such as thinner, benzine,
alcohol, chemical cloths, repellent, insecticide
and sunscreen.
– Handling the camcorder with above
substances on your hands.
– Leaving the casing in contact with rubber or
vinyl objects for a long period of time.
About care and storage of the lens
• Wipe the surface of the lens clean with a soft
cloth in the following instances:
– When there are fingerprints on the lens
surface.
– In hot or humid locations
– When the lens is exposed to salty air such as
at the seaside.
• Store in a well-ventilated location subject to
little dirt or dust.
• To prevent mold, periodically clean the lens as
described above. It is recommended that you
operate your camcorder about once a month to
keep it in optimum state for a long time.
On charging the pre-installed
rechargeable battery
Your camcorder has a pre-installed
rechargeable battery to retain the date, time,
and other settings even when the POWER
switch is set to OFF (CHG). The pre-
installed rechargeable battery is always
charged while your camcorder is connected
to the wall socket via the AC Adaptor or
while the battery pack is attached. The
rechargeable battery will be fully
discharged in about 3 months if you do
not use your camcorder at all. Use your
camcorder after charging the pre-installed
rechargeable battery.
However, even if the pre-installed
rechargeable battery is not charged, the
camcorder operation will not be affected as
long as you are not recording the date.
95
On trademarks
Notes on the License
• “Handycam” and
are registered trademarks of Sony Corporation.
ANY USE OF THIS PRODUCT OTHER THAN
CONSUMER PERSONAL USE IN ANY
MANNER THAT COMPLIES WITH THE
MPEG-2 STANDARD FOR ENCODING
VIDEO INFORMATION FOR PACKAGED
MEDIA IS EXPRESSLY PROHIBITED
WITHOUT A LICENSE UNDER APPLICABLE
PATENTS IN THE MPEG-2 PATENT
PORTFOLIO, WHICH LICENSE IS
• “AVCHD” and “AVCHD” logotype are
trademarks of Matsushita Electric Industrial
Co., Ltd. and Sony Corporation.
• “Memory Stick,” “
Duo,” “
PRO Duo,” “
“Memory Stick PRO-HG Duo,”
“
,” “Memory Stick
,” “Memory Stick
,”
AVAILABLE FROM MPEG LA, L.L.C., 250
STEELE STREET, SUITE 300, DENVER,
COLORADO 80206.
,” “Memory Stick
,”
Micro,” “MagicGate,” “
“MagicGate Memory Stick” and “MagicGate
Memory Stick Duo” are trademarks or
THIS PRODUCT IS LICENSED UNDER THE
AVC PATENT PORTFOLIO LICENSE FOR
THE PERSONAL AND NON-COMMERCIAL
USE OF A CONSUMER TO
(i) ENCODE VIDEO IN COMPLIANCE WITH
THE AVC STANDARD (“AVC VIDEO”) AND /
OR
(ii) DECODE AVC VIDEO THAT WAS
ENCODED BY A CONSUMER ENGAGED IN
A PERSONAL AND
NON-COMMERCIAL ACTIVITY AND/OR
WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED TO PROVIDE AVC
VIDEO. NO LICENSE IS GRANTED OR
SHALL BE IMPLIED FOR ANY OTHER USE.
ADDITIONAL INFORMATION MAY BE
OBTAINED FROM MPEG LA, L.L.C.
registered trademarks of Sony Corporation.
• “InfoLITHIUM” is a trademark of Sony
Corporation.
• “x.v.Colour” is a trademark of Sony
Corporation.
• Dolby and the double-D symbol are trademarks
of Dolby Laboratories.
• Dolby Digital 5.1 Creator is a trademark of
Dolby Laboratories.
• HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
• Microsoft, Windows, and Windows Media are
trademarks or registered trademarks of U.S.
Microsoft Corporation in the U.S. and other
countries.
• Macintosh and Mac OS are registered
trademarks of Apple Inc. in the U.S. and other
countries.
SEE <HTTP://MPEGLA.COM>
“C Library,” “Expat,” “zlib,” and “libjpeg”
software are provided in your camcorder. We
provide this software based on license agreements
with their owners of copyright. Based on requests
by the owners of copyright of these software
applications, we have an obligation to inform you
of the following. Please read the following
sections.
Read “license1.pdf” in the “License” folder on the
CD-ROM. You will find licenses (in English) of
“C Library,” “Expat,” “zlib,” and “libjpeg”
software.
• Intel, Intel Core, and Pentium are trademarks or
registered trademarks of Intel Corporation or its
subsidiaries in the United States and other
countries.
• Adobe, the Adobe logo, and Adobe Acrobat are
either registered trademarks or trademarks of
Adobe Systems Incorporated in the United
States and/or other countries.
All other product names mentioned herein may be
the trademarks or registered trademarks of their
respective companies. Furthermore, ™ and “®”
are not mentioned in each case in this Handbook.
96
On GNU GPL/LGPL applied software
The software that is eligible for the following
GNU General Public License (hereinafter referred
to as “GPL”) or GNU Lesser General Public
License (hereinafter referred to as “LGPL”) are
included in the camcorder.
This informs you that you have a right to have
access to, modify, and redistribute source code for
these software programs under the conditions of
the supplied GPL/LGPL.
Source code is provided on the web. Use the
following URL to download it. When
downloading the source code, select HDR-SR7 as
the model for your camcorder.
http://www.sony.net/Products/Linux/
We would prefer you do not contact us about the
contents of source code.
Read “license2.pdf” in the “License” folder on the
CD-ROM. You will find licenses (in English) of
“GPL,” and “LGPL” software.
To view the PDF, Adobe Reader is needed. If it is
not installed on your computer, you can download
it from the Adobe Systems web page:
http://www.adobe.com/
97
QIduicek Rnetfeirefnyceing parts and controls
The numbers in ( ) are reference pages.
An Active Interface Shoe compatible
microphone (optional) will take
precedence when connected.
G
(Movie)/
(Still) mode lamps
(20)
H
I
/CHG (charge) lamp (16)
(flash) button (31)
K Tripod receptacle
Attach the tripod (optional: the length of
the screw must be less than 5.5 mm
(7/32 in.)) to the tripod receptacle using
a tripod screw.
98
A Active Interface Shoe
The Active Interface Shoe supplies
power to optional accessories such as a
video light, a flash, or a microphone.
The accessory can be turned on or off as
you operate the POWER switch on your
camcorder. Refer to the operating
instructions supplied with your
accessory for details.
The Active Interface Shoe has a safety
device for fixing the installed accessory
securely. To connect an accessory, press
down and push it to the end, and then
tighten the screw. To remove an
accessory, loosen the screw, and then
press down and pull out the accessory.
• When you are recording movies with an
external flash (optional) connected to the
accessory shoe, turn off the power of the
external flash to prevent charging noise
being recorded.
• You cannot use an external flash (optional)
and the built-in flash at the same time.
• When an external microphone (optional) is
connected, it takes precedence over the
B Hook for a shoulder belt
Attach a shoulder belt (optional).
99
Handycam Station
B Interface connector
C
HDR-CX6EK: You cannot input signals
to your camcorder through this jack.
Lights up in red during recording.
Flashes when remaining “Memory Stick
PRO Duo” space or battery power is
low.
D Remote sensor/Infrared port
towards the remote sensor to operate
your camcorder.
101
Remote Commander
b Notes
• Remove the insulation sheet before using the
Remote Commander.
Insulation sheet
• PointtheRemoteCommandertowardstheremote
• When no commands have been sent from the
Remote Commander in a certain period, the
orange frame disappears. When you press any of
b/ B/ v/ V, or ENTER again, the frame appears
at the position where it was displayed last.
• You cannot select some buttons on the LCD
screen using b / B / v / V.
To change the battery of the Remote
Commander
1 While pressing on the tab, inset your
fingernail into the slit to pull out the battery
case.
Displays the date and time or camera setting
dataoftherecordedimageswhenyoupressthis
during playback.
The on-screen image when you press this
button will be recorded as a still image.
2 Place a new battery with the + side facing
up.
3 Insert the battery case back into the Remote
Commander until it clicks.
Tab
H Transmitter
WARNING
Battery may explode if mistreated. Do not
recharge, disassemble or dispose of in
fire.
Displays a VISUAL INDEX screen during
playback.
• When the lithium battery becomes weak, the
operating distance of the Remote Commander
may shorten, or the Remote Commander may
not function properly. In this case, replace the
battery with a Sony CR2025 lithium battery.
Use of another battery may present a risk of fire
or explosion.
M b / B / v / V / ENTER buttons
When you press any button on the [VISUAL
INDEX]/[
INDEX]/[
INDEX]/Playlist
screen, the orange frame appears on the LCD
screen. Select a desired button or an item with
b / B / v / V, then press ENTER to enter.
102
Indicators displayed during recording/playback
Recording movies
D Recording status ([STBY] (standby) or
[REC] (recording))
E Counter (hour/minute/second)
Recording still images
M This appears while a still image is being
saved.
N Recording folder
O Return button
P Playback mode
Viewing movies
Q Currently playing movie number/
Number of total recorded movies
T Playing back image quality
U Currently playing still image number/
Number of total recorded still images
W Data file name
Viewing still images
z Tips
• As the number of still images recorded on a
“Memory Stick PRO Duo” increases, new
folders are automatically created to store them.
103
Upper right
Indicators when you made
changes
Indicator
Meaning
Fader (75)
Following indicators appear during
recording/playback to indicate the settings
of your camcorder.
LCD backlight off (21)
Bottom
Upper left
Upper right
Center
Indicator
Meaning
Digital effect (75)
Manual focus (72)
9
SCENE SELECTION
(73)
Bottom
Upper left
Backlight (32)
.
n
SteadyShot off (61)
Indicator
Meaning
5.1ch surround recording/
playback (30)
SPOT METER (73)/
REDEYE REDUC (62)
MICREF LEVEL low
(76)
X.V.COLOR (61)
WIDE SELECT (60)
Data code during recording
Center
The recording date and time is recorded
automatically on the “Memory Stick PRO
Duo.” They are not displayed while
recording. However, you can check them as
Indicator
Meaning
Continuous slide show
(38)
NightShot (32)
Super NightShot (75)
PictBridge connecting
(52)
E
Warning (84)
104
Quick Reference
Glossary
x 5.1ch surround sound
x Dolby Digital
A system that plays back sound on 6 speakers, 3 at
the front (left, right and center) and 2 at the rear
(right and left) with an additional low-pass
subwoofer counted as a 0.1 channel for
frequencies of 120 Hz or lower.
An audio encoding (compression) system
developed by Dolby Laboratories Inc.
x Dolby Digital 5.1 Creator
Sound compression technology developed by
Dolby Laboratories Inc. which compresses audio
efficiently while preserving high sound quality.
Sounds are compressed effectively with high
quality sound, and it enables producing 5.1ch
surround sound.
x AVCHD format
A high definition digital video camera format
used to record an HD (high definition) signal
using the MPEG-4 AVC/H.264 format.
x JPEG
JPEG stands for Joint Photographic Experts
Group, a still image data compression (data
capacity reduction) standard. Your camcorder
records still images in JPEG format.
x MPEG
MPEG stands for Moving Picture Experts Group,
the group of standards for the coding (image
compression) of video (movie) and audio. There
are MPEG1 and MPEG2 formats. Your
camcorder records movies with SD (standard
definition) image quality in MPEG2 format.
x MPEG-4 AVC/H.264
The latest image coding format standardized
jointly by two international standardization
organizations, the ISO-IEC and the ITU-T, in
2003. Compared with the conventional MPEG2
format, MPEG-4 AVC/H.264 has more than twice
the efficiency. Your camcorder employs MPEG-4
AVC/H.264 to encode high definition movies.
x VBR
VBR stands for Variable Bit Rate, the recording
format for automatically controlling the bit rate
(the volume of recording data in a given time
segment) according to the scene being recorded.
For fast-moving video, a lot of “Memory Stick
PRO Duo” space is used to produce a clear image,
so the recording time to the “Memory Stick PRO
Duo” shortens.
x Thumbnail
Reduced-size images which enable you to view
many images at the same time. [VISUAL
INDEX], [
INDEX], [
INDEX], etc. are
thumbnail display system.
105
Quick Reference
Index
Connection
Numeric
A
D
G
DELETE
H
A.SHUT OFF (Auto shut off)
“Memory Stick PRO
B
HD (high definition) image
Backup........See Saving images
Button-type lithium battery
E
C
F
I
Image quality
106
Index screen display button
Movie
Q
R
REC LAMP (Recording lamp)
INFO (“Memory Stick PRO
Remaining
“InfoLITHIUM” battery pack
N
J
Number of recordable
L
“Memory Stick PRO
O
LCD BL LEVEL (LCD back
Operation confirmation beep
REMOTE CTRL (Remote
S
P
M
SD (standard definition) image
MANAGE MEMORY STICK
“Memory Stick PRO-HG Duo”
Pre-installed rechargeable
107
Still image
X
Z
T
U
V
W
108
Additional information on this product and answers
to frequently asked questions can be found at our
Customer Support Website.
http://www.sony.net/
|