Sony Blu BDV E2100 User Manual

4-446-733-11(1)

Blu-ray Disc™/

DVD Home Theatre

System

Operating Instructions

BDV-E6100/BDV-E4100/BDV-E3100/BDV-E2100

NOTE:

Blu-ray Disc/DVD receiver

(HBD-E6100/HBD-E4100/

HBD-E3100/HBD-E2100)

This equipment must not be co-located or

operated in conjunction with any other

antenna or transmitter.

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the user

is encouraged to try to correct the interference

by one or more of the following measures:

– Reorient or relocate the receiving antenna

(aerial).

This equipment complies with FCC radiation

exposure limits set forth for an uncontrolled

environment and meets the FCC radio

frequency (RF) Exposure Guidelines in

Supplement C to OET65.

This equipment should be installed and

operated keeping the radiator at least 20cm or

more away from person’s body (excluding

extremities: hands, wrists, feet and ankles).

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings.

Install in accordance with the

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/

TV technician for help.

manufacturer’s instructions.

8) Do not install near any heat sources such

as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that

produce heat.

CAUTION

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type

plug has two blades and a third grounding

prong. The wide blade or the third prong

are provided for your safety. If the

provided plug does not fit into your outlet,

consult an electrician for replacement of

the obsolete outlet.

Properly shielded and grounded cables and

connectors must be used for connection to

host computers and/or peripherals in order to

meet FCC emission limits.

10) Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories

specified by the manufacturer.

3^US

12) Use only with the cart, stand, tripod,

bracket, or table specified by the

This equipment complies with IC radiation

exposure limits set forth for an uncontrolled

environment and meets RSS-102 of the IC

radio frequency (RF) Exposure rules.

This equipment should be installed and

operated keeping the radiator at least 20cm or

more away from person’s body (excluding

extremities: hands, wrists, feet and ankles).

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

Precautions

On power sources

13) Unplug this apparatus during lightning

storms or when unused for long periods of

time.

• The unit is not disconnected from the mains

as long as it is connected to the AC outlet,

even if the unit itself has been turned off.

• As the main plug is used to disconnect the

unit from the mains, connect the unit to an

easily accessible AC outlet. Should you

notice an abnormality in the unit, disconnect

the main plug from the AC outlet

14) Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or

objects have fallen into the apparatus, the

apparatus has been exposed to rain or

moisture, does not operate normally, or

has been dropped.

immediately.

On watching 3D video

images

For the customers in

Canada

To reduce the risk of fire or electric shock, do

not expose this appliance to dripping or

splashing, and do not place objects filled with

liquids, such as vases, on the appliance.

Some people may experience discomfort

(such as eye strain, fatigue, or nausea) while

watching 3D video images. Sony recommends

that all viewers take regular breaks while

watching 3D video images. The length and

frequency of necessary breaks will vary from

person to person. You must decide what works

best. If you experience any discomfort, you

should stop watching the 3D video images

until the discomfort ends; consult a doctor if

you believe necessary. You should also

review (i) the instruction manual and/or the

caution message of any other device used

with, or Blu-ray Disc contents played with this

product and (ii) our website

(http://esupport.sony.com/) for the latest

information. The vision of young children

(especially those under six years old) is still

under development. Consult your doctor (such

as a pediatrician or eye doctor) before

allowing young children to watch 3D video

images.

The serial number is located on the bottom

exterior.

Properly shielded and grounded cables and

connectors must be used for connection to

host computers and/or peripherals.

Blu-ray Disc/DVD receiver

(HBD-E6100/HBD-E4100/

HBD-E3100/HBD-E2100)

Operation is subject to the following two

conditions: (1) this device may not cause

interference, and (2) this device must accept

any interference, including interference that

may cause undesired operation of this device.

Adults should supervise young children to

ensure they follow the recommendations

listed above.

4^US

**Manufactured under license under

U.S. Patent Nos: 5,956,674;

Copy Protection

• Please be advised of the advanced content

protection systems used in both Blu-ray Disc

and DVD media. These systems, called

AACS (Advanced Access Content System)

and CSS (Content Scramble System), may

contain some restrictions on playback,

analog output, and other similar features.

The operation of this product and the

restrictions placed may vary depending on

the date of purchase, as the governing board

of the AACS may adopt or change its

restriction rules after the time of purchase.

• Cinavia Notice

5,974,380; 6,226,616; 6,487,535;

7,212,872; 7,333,929; 7,392,195;

7,272,567 & other U.S. and worldwide

patents issued & pending. DTS-HD,

the Symbol, & DTS-HD and the

Symbol together are registered

trademarks of DTS, Inc. Product

includes software. © DTS, Inc. All

Rights Reserved.

• This system incorporates High-Definition

Multimedia Interface (HDMI

technology.

)

The terms HDMI and HDMI High-

Definition Multimedia Interface, and the

HDMI Logo are trademarks or registered

trademarks of HDMI Licensing LLC in the

United States and other countries.

• Java is a trademark of Oracle and/or its

affiliates.

This product uses Cinavia technology to

limit the use of unauthorized copies of some

commercially-produced film and videos and

their soundtracks. When a prohibited use of

an unauthorized copy is detected, a message

will be displayed and playback or copying

will be interrupted.

• “DVD logo” is a trademark of DVD Format/

Logo Licensing Corporation.

• “Blu-ray Disc”, “Blu-ray”, “Blu-ray 3D”,

“BD-LIVE”, “BONUSVIEW”, and logos

are trademarks of the Blu-ray Disc

Association.

• “Blu-ray Disc”, “DVD+RW”, “DVD-RW”,

“DVD+R”, “DVD-R”, “DVD VIDEO”, and

“CD” logos are trademarks.

More information about Cinavia technology

is provided at the Cinavia Online Consumer

Information Center at

http://www.cinavia.com. To request

additional information about Cinavia by

mail, send a postcard with your mailing

address to: Cinavia Consumer Information

Center, P.O. Box 86851, San Diego, CA,

92138, USA.

• “BRAVIA” is a trademark of Sony

Corporation.

Copyrights and Trademarks

• This system incorporates with Dolby*

Digital and Dolby Pro Logic adaptive matrix

surround decoder and the DTS** Digital

Surround System.

• “AVCHD 3D/Progressive” and the

“AVCHD 3D/Progressive” logo are

trademarks of Panasonic Corporation and

Sony Corporation.

* Manufactured under license from

Dolby Laboratories. Dolby, Pro Logic,

and the double-D symbol are

•

, “XMB”, and “xross media bar” are

trademarks of Sony Corporation and Sony

Computer Entertainment Inc.

trademarks of Dolby Laboratories.

• “PlayStation” is a registered trademark of

Sony Computer Entertainment Inc.

• “Sony Entertainment Network logo” and

“Sony Entertainment Network” are

trademarks of Sony Corporation.

5^US

• Music and video recognition technology and

related data are provided by Gracenote .

Gracenote is the industry standard in music

recognition technology and related content

delivery. For more information, please visit

www.gracenote.com.

CD, DVD, Blu-ray Disc, and music and

video-related data from Gracenote, Inc.,

present Gracenote. One or more patents

owned by Gracenote apply to this product

and service. See the Gracenote website for a

nonexhaustive list of applicable Gracenote

patents. Gracenote, CDDB, MusicID,

MediaVOCS, the Gracenote logo and

logotype, and the “Powered by Gracenote”

logo are either registered trademarks or

trademarks of Gracenote in the United States

and/or other countries.

• This product incorporates proprietary

technology under license from Verance

Corporation and is protected by U.S. Patent

7,369,677 and other U.S. and worldwide

patents issued and pending as well as

certain aspects of such technology. Cinavia

is a trademark of Verance Corporation.

engineering or disassembly is prohibited.

• Windows Media is either a registered

trademark or trademark of Microsoft

Corporation in the United States and/or other

countries.

This product is protected by certain

intellectual property rights of Microsoft

Corporation. Use or distribution of such

technology outside of this product is

prohibited without a license from Microsoft

or an authorized Microsoft subsidiary.

Content owners use Microsoft

PlayReady™ content access technology to

protect their intellectual property, including

copyrighted content. This device uses

PlayReady technology to access PlayReady-

protected content and/or WMDRM-

protected content. If the device fails to

properly enforce restrictions on content

usage, content owners may require

Microsoft to revoke the device’s ability to

consume PlayReady-protected content.

Revocation should not affect unprotected

content or content protected by other content

access technologies. Content owners may

require you to upgrade PlayReady to access

their content. If you decline an upgrade, you

will not be able to access content that

requires the upgrade.

• Wi-Fi , Wi-Fi Protected Access and Wi-Fi

Alliance are registered marks of the Wi-Fi

Alliance.

• Wi-Fi CERTIFIED™, WPA™, WPA2™

and Wi-Fi Protected Setup™ are marks of

the Wi-Fi Alliance.

• The N Mark is a trademark or registered

trademark of NFC Forum, Inc. in the United

States and in other countries.

• Android is a trademark of Google Inc.

• The Bluetooth word mark and logos are

registered trademarks owned by Bluetooth

SIG, Inc. and any use of such marks by Sony

Corporation is under license. Other

trademarks and trade names are those of their

respective owners.

• MPEG Layer-3 audio coding technology and

patents licensed from Fraunhofer IIS and

Thomson.

• DLNA™, the DLNA Logo and DLNA

CERTIFIED™ are trademarks, service

marks, or certification marks of the Digital

Living Network Alliance.

6^US

• Opera Devices SDK from Opera Software

You agree that your non-exclusive license to

use the Gracenote Data, the Gracenote

Software, and Gracenote Servers will

terminate if you violate these restrictions. If

your license terminates, you agree to cease

any and all use of the Gracenote Data, the

Gracenote Software, and Gracenote Servers.

Gracenote reserves all rights in Gracenote

Data, the Gracenote Software, and the

Gracenote Servers, including all ownership

rights. Under no circumstances will Gracenote

become liable for any payment to you for any

information that you provide. You agree that

Gracenote, Inc. may enforce its rights under

this Agreement against you directly in its own

name.

The Gracenote service uses a unique identifier

to track queries for statistical purposes. The

purpose of a randomly assigned numeric

identifier is to allow the Gracenote service to

count queries without knowing anything about

who you are. For more information, see the

web page for the Gracenote Privacy Policy for

the Gracenote service.

The Gracenote Software and each item of

Gracenote Data are licensed to you “AS IS.”

Gracenote makes no representations or

warranties, express or implied, regarding the

accuracy of any Gracenote Data from in the

Gracenote Servers. Gracenote reserves the

right to delete data from the Gracenote Servers

or to change data categories for any cause that

Gracenote deems sufficient. No warranty is

made that the Gracenote Software or

Gracenote Servers are error-free or that

functioning of Gracenote Software or

Gracenote Servers will be uninterrupted.

Gracenote is not obligated to provide you with

new enhanced or additional data types or

categories that Gracenote may provide in the

future and is free to discontinue its services at

any time.

• All other trademarks are trademarks of their

respective owners.

• Other system and product names are

generally trademarks or registered

trademarks of the manufacturers. ™ and ®

marks are not indicated in this document.

End User License

Information

Gracenote End User License

Agreement

This application or device contains software

from Gracenote, Inc. of Emeryville, California

(“Gracenote”). The software from Gracenote

(the “Gracenote Software”) enables this

application to perform disc and/or file

identification and obtain music-related

information, including name, artist, track, and

title information (“Gracenote Data”) from

online servers or embedded databases

(collectively, “Gracenote Servers”) and to

perform other functions. You may use

Gracenote Data only by means of the intended

End-User functions of this application or

device.

You agree that you will use Gracenote Data,

the Gracenote Software, and Gracenote

Servers for your own personal non-

commercial use only. You agree not to assign,

copy, transfer or transmit the Gracenote

Software or any Gracenote Data to any third

party. YOU AGREE NOT TO USE OR

EXPLOIT GRACENOTE DATA, THE

GRACENOTE SOFTWARE, OR

GRACENOTE SERVERS, EXCEPT AS

EXPRESSLY PERMITTED HEREIN.

7^US

GRACENOTE DISCLAIMS ALL

WARRANTIES EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO,

IMPLIED WARRANTIES OF

About These Operating

Instructions

• The instructions in these Operating

Instructions describe the controls on the

remote control. You can also use the controls

on the unit if they have the same or similar

names as those on the remote control.

• In this manual, “disc” is used as a general

reference for BDs, DVDs, or CDs unless

otherwise specified by the text or

MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE, TITLE, AND

NON-INFRINGEMENT. GRACENOTE

DOES NOT WARRANT THE RESULTS

THAT WILL BE OBTAINED BY YOUR

USE OF THE GRACENOTE SOFTWARE

OR ANY GRACENOTE SERVER. IN NO

CASE WILL GRACENOTE BE LIABLE

FOR ANY CONSEQUENTIAL OR

INCIDENTAL DAMAGES OR FOR ANY

LOST PROFITS OR LOST REVENUES.

illustrations.

• The instructions in this manual are for

BDV-E6100, BDV-E4100, BDV-E3100,

and BDV-E2100. BDV-E6100 is the model

used for illustration purposes. Any

difference in operation is clearly indicated in

the text, for example, “BDV-E6100 only”.

• Some illustrations are presented as

conceptual drawings, and may be different

from the actual products.

• The items displayed on the TV screen may

vary depending on the area.

• The default setting is underlined.

8^US

Table of Contents

About These Operating Instructions .... 8

Unpacking .......................................... 10

Guide to Parts and Controls ............... 13

Tuner

Listening to the Radio ........................ 38

Other Operations

Getting Started

Step 1: Installing the

Speakers .............................. 17

Step 2: Connecting the

Using the Control for HDMI Function

for “BRAVIA” Sync ................... 40

Setting the Speakers ........................... 40

Using the Sleep Timer ........................ 42

Deactivating the Buttons on the

Unit ............................................. 42

Controlling Your TV with the

Supplied Remote Control ............ 42

Saving Power in Standby Mode ......... 43

Browsing Websites ............................ 43

System ................................. 18

Connecting the speakers ....... 18

Connecting the TV .................. 19

Connecting the other

equipment

(Set-top box, etc.) ............... 20

Connecting the antenna

(aerial) ................................. 21

Step 3: Preparing for Network

Connection .......................... 21

Step 4: Performing the Easy

Setup .................................... 23

Step 5: Selecting the Playback

Source .................................. 24

Step 6: Enjoying Surround

Sound ................................... 24

Settings and

Adjustments

Using the Setup Display ..................... 45

[Network Update] .............................. 46

[Screen Settings] ................................ 46

[Audio Settings] ................................. 48

[BD/DVD Viewing Settings] ............. 49

[Parental Control Settings] ................. 49

[System Settings] ............................... 50

[Network Settings] ............................. 51

[Easy Network Settings] .................... 52

[Resetting] .......................................... 52

Playback

Playing a Disc .................................... 26

Playing from a USB Device ............... 28

Enjoying music from a Bluetooth

device .......................................... 28

Connecting to a smartphone by

Additional Information

Precautions ......................................... 52

Notes about Discs ............................... 55

Troubleshooting ................................. 55

Playable Discs .................................... 60

Playable Types of Files ...................... 61

Supported Audio Formats .................. 63

Specifications ..................................... 63

Language Code List ........................... 66

Index ................................................... 68

One-touch listening function

(NFC) .......................................... 30

Playing via a Network ........................ 32

Available Options .............................. 35

Sound Adjustment

Selecting the Audio Format,

Multilingual Tracks, or

Channel ....................................... 37

Enjoying Multiplex Broadcast

Sound .......................................... 38

9^US

Unpacking

• Operating Instructions

• Quick Setup Guide

• Subwoofer (1)

• Speaker Installation Guide

• Remote control (1)

• R6 (size AA) batteries (2)

• FM wire antenna (aerial) (1)

• Speaker-bottom covers (4)

• Bases (4)

BDV-E6100 only

• Front speakers (2)

• Lower parts of the front and surround

speakers (4)

• Surround speakers (2)

• Screws (large) (4)

• Screws (small) (16)

• Center speaker (1)

10^US

• Lower parts of the front speakers (2)

BDV-E4100 only

• Front speakers (2)

• Screws (large) (2)

• Screws (small) (8)

• Surround speakers (2)

BDV-E3100 only

• Front speakers (2)

• Center speaker (1)

• Subwoofer (1)

• Surround speakers (2)

• Center speaker (1)

• Speaker-bottom covers (2)

• Bases (2)

11^US

• Subwoofer (1)

BDV-E2100 only

• Front speakers (2)

• Surround speakers (2)

• Center speaker (1)

• Subwoofer (1)

12^US

Guide to Parts and Controls

For more information, refer to the pages indicated in parentheses.

Front panel

Slot

BDV-E2100

only

A "/1 (on/standby)

Note

Turns on the unit, or sets it to standby

mode.

During the demonstration, the volume

level may be higher than the volume level

you have set.

B Disc tray (page 26)

(USB) port (page 28)

(BDV-E6100/BDV-E4100/

BDV-E3100 only) Place your

fingernail in the slot to open the cover.

(N-Mark) (page 31)

Position the NFC-compatible device

near this indication to activate the NFC

function.

(remote control sensor)

D Play operation buttons

G Front panel display

H LED indicator

Z (open/close)

^{a) b)}(play)

^b)(stop)

White: Lights up when the unit is

turned on.

Blue (for Bluetooth status):

– System is ready for pairing: Flashes

quickly

– During pairing: Flashes quickly

– During connection: Flashes

– Connection is established: Lights up

VOL +/–^a)

./> (previous/next)

FUNCTION (page 24)

Selects the playback source.

N and VOL + buttons have a tactile dot.

Use the tactile dot as a reference when

operating the unit.

Hold down N on the unit for more than

2 seconds, the built-in sound

demonstration will be played back on the

system. Press x to stop the demonstration.

13^US

Indicators in the front panel display

A Lights up when stereo sound is

F Displays the system’s status,

received. (Radio only)

such as radio frequency, etc.

When you press DISPLAY, the stream

information/decoding status is

displayed when the function is set to

“TV”.

The stream information/decoding

status may not appear depending on

the stream or item being decoded.

B Lights up when repeat play is

activated.

C Lights up when the system is

playing via the PARTY

STREAMING function.

D Lights up when muting is on.

E Lights up when the HDMI (OUT)

jack is correctly connected to an

HDCP (High-bandwidth Digital

Content Protection) compliant

equipment with HDMI or DVI

Note

When the [Main Unit illumination] is set to

[Auto] in [System Settings], the front panel

display lights off if you do not operate the unit for

about 10 seconds.

(Digital Visual Interface) input.

Rear panel

A SPEAKERS jacks (page 18)

D HDMI (OUT) jack (page 19)

B TV (DIGITAL IN OPTICAL) jack

E AUDIO IN (L/R) jacks (page 20)

(page 19)

F ANTENNA (FM) terminal

C LAN (100) terminal (page 21)

(page 21)

14^US

A Z (open/close)

Remote control

Opens or closes the disc tray.

SPEAKERS TVyAUDIO

Selects whether TV sound is output

from the system’s speakers or the TV’s

speaker(s). This function works only

when you set [Control for HDMI] to

[On] (page 50).

TV "/1 (on/standby) (page 43)

Turns on the TV or sets it to standby

mode.

"/1 (on/standby) (pages 23, 39)

Turns on the system or sets it to

standby mode.

B Number buttons (pages 39, 43)

Enters the title/chapter numbers, preset

station number, etc.

AUDIO (page 37)

Selects the audio format/track.

SUBTITLE

Selects the subtitle language when

multilingual subtitles are recorded on a

BD-ROM/DVD VIDEO.

Number 5, AUDIO, VOL +, and N

buttons have a tactile dot. Use the tactile

dot as a reference when operating the

remote control.

C Color buttons

Short cut keys for selecting items on

some BD menus (can also be used for

Java interactive operations on BDs).

•

: For TV operations

(For details, see “Controlling Your TV

with the Supplied Remote Control”

(page 42).)

D TOP MENU

Opens or closes the BD’s or DVD’s

Top Menu.

POP UP/MENU

Opens or closes the BD-ROM’s Pop-

up Menu, or the DVD’s menu.

The system automatically

returns to standby mode

If any button on the unit or remote control

is not pressed within 30 minutes, the

system automatically returns to standby

mode.

OPTIONS (pages 25, 35, 44)

Displays the options menu on the TV

screen or in the front panel display.

(The location differs depending on the

selected function.)

RETURN

Returns to the previous display.

15^US

B/V/v/b

N PLAY

Moves the highlight to a displayed

item.

Starts or re-starts playback (resume

play).

Activates One-Touch Play (page 40)

when the system is on and set to the

“BD/DVD” function.

(enter)

Enters the selected item.

E MUSIC EQ

X PAUSE

Pauses or re-starts playback.

x STOP

Selects the pre-programmed equalizer

when listening to music.

HOME (pages 23, 40, 45)

Stops playback and remembers the

stop point (resume point). The resume

point for a title/track is the last point

you played or the last photo for a photo

folder.

Enters or exits the system’s home

menu.

SOUND MODE (page 24)

Selects the sound mode.

NETFLIX

Stops the built-in sound

demonstration.

Accesses the “NETFLIX” online

service.

Radio operation buttons

See “Tuner” (page 38).

PRESET +/–

SEN

Accesses the “Sony Entertainment

Network™” online service.

TUNING +/–

F Playback operation buttons

See “Playback” (page 26).

G MUTING

Turns off the sound temporarily.

VOL +/–

Adjusts the volume.

TV VOL +/–

./> (previous/next)

Selects the previous/next chapter,

track, or file.

m/M (fast/slow/freeze frame)

Adjusts the TV volume.

TV INPUT

Switches the TV’s input source

between the TV and other input

sources.

Fast reverse/fast forward music during

playback. Each time you press the

button, the search speed changes.

Activates slow-motion play when

pressed for more than one second in

pause mode.

H DISPLAY (pages 27, 32, 39, 44)

Plays one frame at a time when pressed

in pause mode.

Displays playback and web browsing

information on the TV screen.

Displays the preset radio station,

frequency, etc., in the front panel

display.

Note

During Blu-ray 3D Disc playback, slow-

motion reverse play and single-frame

reverse play are not available.

I FOOTBALL

Produces optimized sound for

watching football match broadcasting.

16^US

J BLUETOOTH

Selects the “BT” function.

When the blue LED indicator lights off

during “BT” function, press to start

pairing or connect to paired Bluetooth

device.

Getting Started

Step 1: Installing the

Speakers

Install the speakers by referring to the

illustration below.

FUNCTION (page 24)

Selects the playback source.

K SLEEP (page 42)

Sets the sleep timer.

A Front left speaker (L)

B Front right speaker (R)

C Center speaker

D Surround left speaker (L)

E Surround right speaker (R)

F Subwoofer

G TV

Installing the surround

speakers in rear position

(Speaker layout: [Standard])

17^US

Installing all speakers in

front position

Step 2: Connecting the

System

(Speaker layout: [All Front])

D A F

C B E

Do not connect the AC power cord (mains

lead) of the unit to a wall outlet (mains)

until all the other connections are made.

(BDV-E6100/BDV-E4100 only) To

assemble the speakers, refer to the supplied

“Speaker Installation Guide”.

Note

When you connect other equipment with a

volume control, turn down the volume of the

equipment to a level where sound is not distorted.

Note

• Be sure to select the speakers layout setting

(page 41) according to your speakers

placement.

Connecting the

speakers

• Use caution when placing the speakers and/or

speaker stands attached to the speakers on a

specially treated (waxed, oiled, polished, etc.)

floor, as staining or discoloration may result.

• Do not lean or hang on a speaker, as it may fall

down.

Connect the speaker cords to match the

color of the SPEAKERS jacks of the unit.

When connecting to the unit, insert the

connector until it clicks.

Red

Gray

(Surround right

(Front right

speaker (R))

Purple

Tip

(Subwoofer) speaker (R))

You can install the speakers on a wall. For details,

refer to the supplied “Speaker Installation

Guide”.

White

Green

Blue

(Front left

(Center (Surround left

speaker (L)) speaker) speaker (L))

18^US

Connecting the TV

Select one of the following connection methods according to the input jacks on your TV.

Video connection

HDMI cable (not supplied)

High Speed HDMI cable

If the HDMI IN jack of your TV is compatible with the ARC (Audio Return Channel) function, digital

audio signal can be output from the TV via an HDMI cable connection. For setting the ARC function,

see [Audio Return Channel] (page 50).

Audio connections

If you do not connect the system to the TV’s HDMI jack that is compatible with the ARC

function, make an appropriate audio connection for listening to TV sound via the system’s

speakers.

High quality

Optical digital cord (not supplied)

Audio cable (not supplied)

DIGITAL OUT

OPTICAL

AUDIO

OUTPUT

Standard

quality

19^US

Connecting the other equipment (Set-top box, etc.)

Connect the system so that video signals from the system and other equipment are output

to the TV, and audio signals from the equipment are output to the system as follows.

Video out

Equipment

(Set-top box, VCR, PlayStation , or

digital satellite receiver, etc.)

Audio out

Signal flow

System

: Video signal

: Audio signal

Select one of the following connection methods according to the jack type of the equipment.

High quality

Optical digital cord (not supplied)

Audio cable (not supplied)

DIGITAL OUT

OPTICAL

AUDIO

OUTPUT

Standard

quality

Note

• If you make either connection above, set [Control for HDMI] in [HDMI Settings] of [System Settings]

to [Off] (page 50).

• You can enjoy equipment sound by selecting the “AUDIO” function for connection B.

20^US

Connecting the antenna

(aerial)

Step 3: Preparing for

Network Connection

Tip

To connect the system to your network, perform

[Easy Network Settings]. For details, see “Step 4:

Performing the Easy Setup” (page 23).

Select the method based on your LAN

(Local Area Network) environment.

• If you use a wireless LAN

The system has built-in Wi-Fi, and you

can connect the system to the network by

making the network settings.

• If you use other than a wireless LAN

Use a LAN cable to connect to the LAN

(100) terminal on the unit.

FM wire antenna (aerial)

(supplied)

Note

• Be sure to fully extend the FM wire antenna

(aerial).

• After connecting the FM wire antenna (aerial),

keep it as horizontal as possible.

Broadband router

LAN cable (not supplied)

Tip

A shielded interface cable (LAN cable), straight

or crossover, is recommended.

21^US

x No Security

Before performing the

network settings

When your wireless LAN router (access

point) is Wi-Fi Protected Setup (WPS)-

compatible, you can easily set the network

settings with the WPS button.

If not, check the following information in

advance, and record it in the space provided

below.

• The network name (SSID*) that

identifies your network**.

Although you can easily make settings,

anyone can intercept wireless

communication or intrude into your

wireless network, even without any

sophisticated tools. Keep in mind that there

is a risk of unauthorized access or

interception of data.

x WEP

WEP applies security to communications

to prevent outsiders from intercepting

communications or intruding into your

wireless network. WEP is a legacy security

technology that enables older devices

which do not support TKIP/AES to be

connected.

• If security is set on your wireless

network, the security key (WEP key,

WPA key)**.

SSID (Service Set Identifier) is a name that

identifies a particular wireless network.

x WPA-PSK (TKIP), WPA2-PSK

(TKIP)

TKIP is a security technology developed in

response to the deficiencies of WEP. TKIP

assures a higher security level than WEP.

** You need to check the settings of your wireless

LAN router to get the information about SSID

and security key. For details:

– visit the following website:

http://www.sony.com/blurayhtsupport/

– refer to the operating instructions supplied

with the wireless LAN router

x WPA-PSK (AES), WPA2-PSK

(AES)

AES is a security technology that uses an

advanced security method distinct from

WEP and TKIP. AES assures a higher

security level than WEP or TKIP.

– consult the manufacturer of the wireless

LAN router

About wireless LAN

security

Since communication via the wireless LAN

function is established by radio waves, the

wireless signal may be susceptible to

interception. To protect wireless

communication, this system supports

various security functions. Be sure to

correctly configure the security settings in

accordance with your network

environment.

22^US

Perform [Easy Initial Settings].

Follow the on-screen

instructions to make the basic

Step 4: Performing the

Easy Setup

settings using B/V/v/b and

Before performing Step 4

Make sure all connections are secure, and

then connect the AC power cord (mains

lead).

B/V/v/b

Follow the Steps below to make the basic

adjustments and network settings for the

system.

Displayed items vary depending on the

area.

After completing the [Easy Initial

Settings], press V/v to select

[Easy Network Settings], then

press

The [Easy Network Settings] display

appears.

Insert two R6 (size AA) batteries

(supplied) by matching the 3

and # ends on the batteries to

the markings inside the

Follow the on-screen

instructions to make the network

settings using B/V/v/b and

compartment.

If the system cannot connect to the

network, see “Network connection”

(page 59) or “Wireless LAN

connection” (page 59).

To recall the [Easy Network

Settings] display

Turn on the TV.

1 Press HOME.

The home menu appears on the TV

screen.

Press [/1.

Switch the input selector on

your TV so that the signal from

the system appears on the TV

screen.

The [Easy Initial Settings] for OSD

language selection appears.

2 Press B/b to select

3 Press V/v to select [Easy Network

Settings], then press

[Setup].

23^US

Step 5: Selecting the

Playback Source

Step 6: Enjoying

Surround Sound

After performing the previous Steps and

starting playback, you can easily enjoy pre-

programmed sound modes that are tailored

to different kinds of sound sources. They

bring the exciting and powerful sound of

movie theaters into your home.

Press FUNCTION repeatedly until

the function you want appears in the

front panel display.

When you press FUNCTION once, the

current function appears in the front panel

display, then each time you press

FUNCTION, the function changes

cyclically as follows.

Selecting the sound

mode

“BD/DVD” t “USB” t “FM” t

“TV” t “BT” t “AUDIO”

Press SOUND MODE repeatedly

during playback until the mode you

want appears in the front panel

display or on the TV screen.

Function and playback source

“BD/DVD”

Disc or network device to be played by the

system

Auto

“USB”

The system automatically selects [Movie] or

[Music] to produce the sound effect

depending on the disc or sound stream.

• 2-channel source: The system simulates

surround sound from 2-channel sources and

outputs sound from the 5.1 channel

speakers.

USB device that is connected to the (USB)

port (page 13)

“FM”

FM radio (page 38)

“TV”

Equipment (TV, etc.) that is connected to the

TV (DIGITAL IN OPTICAL) jack, or a TV

compatible with the Audio Return Channel

function that is connected to the HDMI

(OUT) jack (page 19)

• Multi-channel source: The system outputs

sound from the speakers as it was recorded.

Movie

The system provides the optimized sound for

watching movies.

“BT”

Audio contents of a Bluetooth device

Music

The system provides the optimized sound for

“AUDIO”

Equipment that is connected to the AUDIO

listening to music.

IN (L/R) jacks (page 20)

Digital Music Enhancer

[Digital Music]

Tip

The system reproduces an enhanced sound

for compressed audio.

• Some functions may be changed via the TV

Night

screen by pressing FUNCTION, V/v, and

• You can also press BLUETOOTH on the

remote control to select “BT” function.

Suitable for watching movies at night by

reducing loud sounds while maintaining

clear dialog.

Demo Sound

The system provides ear-catching sound,

suitable for demonstration.

24^US

To select the sound mode

from the option menu

Selecting the football

mode

1 Press OPTIONS and V/v to select

[Sound Mode], then press

Press FOOTBALL during playback.

[Football] appears on the TV screen.

You can experience a feeling of presence in

the stadium when watching a football

match broadcasting.

To turn off the football mode, press

FOOTBALL again to select [Football Off].

The sound mode is changed to the last

selected sound mode.

2 Press V/v to select the sound mode,

then press

To select the pre-

programmed music

equalizer

Press MUSIC EQ repeatedly during

playback.

Note

You can select the sound to suit your

preference.

Each time you press the button, the setting

changes cyclically as follows.

[Standard] t [Rock] t [Hiphop] t

[Electronica]

• Depending on the source, the football mode may

not work well.

• The football mode will be turned off when you

turn off the system.

Tip

You can also select the football mode from the

option menu.

You can also select the music equalizer by

using the option menu in [Music] sound

mode.

Note

The sound mode can be selected only when

[Sound Effect] is set to [Sound Mode On]

(page 48). When [Sound Effect] is set to other

than [Sound Mode On], the sound mode setting

does not apply.

Tip

To enjoy 2-channel source such as a CD in multi-

channel output, we recommend you to select

[Auto].

25^US

Enjoying BONUSVIEW/

BD-LIVE

Playback

Some BD-ROMs with “BD-LIVE Logo*”

have bonus content and other data that can

be downloaded for enjoyment.

Playing a Disc

For playable discs, see “Playable Discs”

(page 60).

Connect the USB device to the

(USB) port (page 28).

For local storage, use a 1 GB or larger

USB memory.

Switch the input selector on

your TV so that the signal from

the system appears on your TV

screen.

Prepare for BD-LIVE (BD-LIVE

only).

Press Z, and place a disc on the

disc tray.

• Connect the system to a network

(page 21).

• Set [BD Internet Connection] to

[Allow] (page 49).

Insert a BD-ROM with

BONUSVIEW/BD-LIVE.

The operation method differs

depending on the disc. Refer to the

operating instructions of the disc.

Press Z to close the disc tray.

Playback starts.

Tip

To delete data in the USB memory, select [Delete

BD Data] in [Video], and press . All data

stored in the buda folder will be deleted.

If playback does not start

automatically, select

[Video], [Music], or

[Photo] category, and press

in the

26^US

Enjoying Blu-ray 3D

Displaying the playback

information

You can enjoy Blu-ray 3D Discs with the

3D logo*.

You can check the playback information,

etc., by pressing DISPLAY.

The displayed information differs

depending on the disc type and system

status.

Prepare for Blu-ray 3D Disc

playback.

• Connect the system to your

3D-compatible TV using a High

Speed HDMI cable (page 19).

• Set [3D Output Setting] and [TV

Screen Size Setting for 3D] in

[Screen Settings] (page 46).

Example: when playing a BD-ROM

Insert a Blu-ray 3D Disc.

The operation method differs

depending on the disc. Refer to the

operating instructions supplied with

the disc.

Tip

A Output resolution/Video frequency

B Title number or name

Refer also to the operating instructions of your

3D-compatible TV.

C The currently selected audio setting

D Available functions (

angle,

audio,

subtitle)

E Playback information

Displays play mode, playing status

bar, disc type, video codec, bit rate,

repeat type, elapsed time, total playing

time

F Chapter number

G The currently selected angle

27^US

Playing from a USB

Device

Enjoying music from a

Bluetooth device

You can play video/music/photo files on a

connected USB device.

For playable types of files, see “Playable

Types of Files” (page 61).

About the Bluetooth

wireless technology

Bluetooth wireless technology is a short-

range wireless technology that enables

wireless data communication between

digital devices. Bluetooth wireless

technology operates within a range of about

10 meters (33 feet).

Connect the USB device to the

(USB) port.

Refer to the operating instructions of

the USB device before connecting.

You do not need wires to get connected as

you do with a USB connection, and you do

not need to place the devices face to face as

you do with wireless infrared technology.

Bluetooth wireless technology is a global

standard supported by thousands of

companies. These companies produce

products that meet the global standard.

Press HOME.

The home menu appears on the TV

screen.

Press B/b to select

[Video],

[Music], or

[Photo].

Press V/v to select

device], then press

[USB

Supported Bluetooth

version and profiles

Note

Profile refers to a standard set of

capabilities for various Bluetooth product

capabilities. This system supports the

following Bluetooth version and profiles.

Supported Bluetooth version:

Bluetooth Specification version 3.0

Supported Bluetooth profiles:

A2DP 1.2 (Advanced Audio Distribution

Profile)

Do not remove the USB device during

operation. To avoid data corruption or

damage to the USB device, turn the system

off before connecting or removing the USB

device.

AVRCP 1.3 (Audio Video Remote Control

Profile)

28^US

Note

Once pairing is completed, the

device is automatically

connected to the system.

Device name appears on the TV

screen.

• To be able to use the Bluetooth function, the

Bluetooth device to be connected must support

the same profile as this system. Even if the

device supports the same profile, the functions

may differ depending on the specifications of

the Bluetooth device.

• The audio playback on this system may be

delayed from that on the Bluetooth device

because of the characteristics of the Bluetooth

wireless technology.

Note

You can pair up to 9 Bluetooth devices. If

the 10th Bluetooth device is paired, the least

recently connected device will be replaced

by the new one.

Start playback on the Bluetooth

device.

Pairing this system with

a Bluetooth device

Adjust the volume.

Pairing is an operation where Bluetooth

devices register with each other

beforehand. Once a pairing operation is

performed, it does not need to be performed

again.

Adjust the volume of the Bluetooth

device first, if the volume level is still

too low, adjust the volume level on the

unit.

To cancel pairing operation

Press HOME or FUNCTION.

Place the Bluetooth device

within 1 meter (3.3 feet) from the

unit.

Connecting to a

Bluetooth device from

this system

Press BLUETOOTH.

You can also select [Bluetooth

AUDIO] from

menu.

[Input] in home

You can connect to a Bluetooth device

from this unit.

Check the following before playing music:

– The Bluetooth function of the Bluetooth

device is turned on.

Set the Bluetooth device in

pairing mode.

For details on setting the Bluetooth

device in pairing mode, refer to the

operating instructions supplied with

the device.

– The pairing has been completed

(page 29).

Select “BLU-RAY HOME

THEATRE SYSTEM” on the

Bluetooth device display.

Press BLUETOOTH.

Note

Perform this step within 5 minutes,

otherwise pairing will be canceled.

To connect to the most recent connected

Bluetooth device, press N. Then proceed to

Step 5.

Note

If passkey is required on the Bluetooth

device, enter “0000”. Passkey may be called

“Passcode”, “PIN code”, “PIN number” or

“Password”.

Press OPTIONS.

29^US

Press V/v repeatedly to select

[Device List], then press

A list of paired Bluetooth devices

Connecting to a

smartphone by One-

touchlisteningfunction

(NFC)

appears.

Press V/v repeatedly to select

the device you want, then press

By holding an NFC-compatible

Press N to start playback.

smartphone near to the

on the unit, the

unit and smartphone proceed to complete

pairing and the Bluetooth connection

automatically.

Adjust the volume.

Adjust the volume of the Bluetooth

device first, if the volume level is still

too low, adjust the volume level on the

unit.

Compatible smartphones

Smartphones with a built-in NFC function

(OS: Android 2.3.3 – 4.0.x, excluding

Android 3.x)

Note

Once the unit and the Bluetooth device are

connected, you can control playback by pressing

N, X, x, m/M and ./>.

What is “NFC”?

NFC (Near Field Communication) is a

technology enabling short-range wireless

communication between various devices,

such as mobile phones and IC tags. Thanks

to the NFC function, data communication

can be achieved easily just by holding the

To disconnect the

Bluetooth device

Press HOME, FUNCTION or RETURN.

To delete a paired Bluetooth

device from the device list

device near the

devices.

on the NFC-compatible

1 Follow Steps 1 to 3 above.

2 Press V/v repeatedly to select the

Download and install the app

“NFC Easy Connect”.

device, then press OPTIONS.

“NFC Easy Connect” is a free app for

Android smartphones that can be

obtained on Google Play. Search for

the app using the keyword “NFC Easy

Connect” on the site, or access the

download site directly by reading the

two-dimensional code below.

Note that “NFC Easy Connect” is free

but data communication fees when

downloading are charged separately.

3 Press V/v repeatedly to select

[Remove], then press

4 Follow the on-screen instructions to

delete the device using B/V/v/b and

Note

While connected to a Bluetooth device, this

system cannot be detected and a connection

cannot be established from another Bluetooth

device.

30^US

Two-dimensional code* for

direct access

Note

• The system only can recognizes and connects to

one NFC-compatible device at a time.

* Use a two-dimensional code reader app.

• Depending on your smartphone, you may need

to turn on the NFC function on your smartphone

in advance. For details, refer to the operating

instructions of the smartphone.

Tip

If pairing and the Bluetooth connection fail, do

the following.

Note

– Relaunch “NFC Easy Connect” and move the

smartphone slowly over the

– Remove the case from the smartphone if using

a commercially available smartphone case.

The app may not be available in some

countries/regions.

Start the “NFC Easy Connect”

app on the smartphone.

Make sure that the application screen

is displayed.

To listen to music

Start playback of an audio source on the

smartphone. For details on playback

operations, refer to the operating

instructions of your smartphone.

Hold the smartphone near to the

on the unit until the

smartphone vibrates.

Tip

If the volume level is low, adjust the volume of

the smartphone first. If the volume level is still

too low, adjust the volume level on the unit.

To stop playback

The playback will be stopped when you

Vibration cue is provided when the

smartphone is recognized by the unit.

After being recognized by the unit,

follow the on-screen instructions

displayed on the smartphone, and

complete the procedure for Bluetooth

connection.

When the Bluetooth connection is

established, the blue LED indicator on

the front panel stops flashing. The

playback time appears in the front

panel display.

perform any of the following items:

– Hold the smartphone near to the

the unit again.

– Stop the music player of the smartphone.

– Turn off the unit or the smartphone.

– Change the function.

– Disable the Bluetooth function on the

smartphone.

31^US

Video streaming control

panel

The control panel appears when a video file

starts playing. The displayed items may

differ depending on the Internet content

provider.

Playing via a Network

Enjoying Sony

Entertainment Network

(SEN)

To display again, press DISPLAY.

Sony Entertainment Network serves as a

gateway delivering selected Internet

content and a variety of on-demand

entertainment straight to your unit.

Tip

A Control display

• Some Internet content requires registration via a

PC before it can be played. For further details,

visit the following website:

Press B/V/v/b or

operations.

for playback

http://www.sony.com/blurayhtsupport/

• Some Internet content may not be available in

some countries/regions.

B Playing status bar

Status bar, cursor indicating the

current position, playing time, duration

of the video file

Prepare for Sony Entertainment

Network.

C Network condition indicator

Indicates signal strength for a

wireless connection.

Connect the system to a network

(page 21).

Indicates a wired connection.

Press SEN.

D Network transmission speed

E The next video file name

Press B/V/v/b to select the

Internet content and a variety of

on-demand entertainment, then

F The currently selected video file name

press

32^US

To play files stored on a

DLNA server via the system

(DLNA Player)

Playing files on a Home

Network (DLNA)

Select the DLNA server icon from

You can play video/music/photo files on

other DLNA-certified equipment by

connecting them to your home network.

[Video],

[Music], or

[Photo] in

the home menu, then select the file that you

want to play.

This unit can be used as a player and

renderer.

Server

• Server: Stores and shares digital media

contents

• Player: Finds and plays digital media

content from the DMS

Player

(This system)

• Renderer: Receives and plays files from

the server, and can be operated by another

equipment (controller)

• Controller: Operates the renderer

equipment

To play remote files by

operating the system

(Renderer) via a DLNA

controller

Server

You can operate the system with a

DLNA-certified controller (a mobile

phone, etc), when playing files stored on a

DLNA server.

Server

Player

(This system)

Renderer

(This system)

Player

Prepare for using the DLNA

function.

Controller

• Connect the system to a network

(page 21).

• Prepare other DLNA-certified

equipment. For details, refer to the

operating instructions of the equipment.

For details on operation, refer to the

operating instructions of the DLNA

controller.

Note

Do not operate the system with the supplied

remote control and a DLNA controller at the same

time.

Tip

The system is compatible with the “Play To”

function of Windows Media Player 12 that

comes standard with Windows 7.

33^US

To use the system as the

PARTY host

Playing the same music

in different rooms

(PARTY STREAMING)

Select a track in

[Music], a radio station

in [Radio],

[AUDIO] or

[Bluetooth AUDIO] in

[Input],

You can play the same music at the same

time on all Sony equipment which are

compatible with the PARTY

STREAMING function and connected to

your home network.

press OPTIONS. Then select [Start

PARTY] to start.

To close, press OPTIONS, then select

[Close PARTY].

Note

Contents in

[Music] and the “FM”,

If content that is not compatible with the PARTY

STREAMING function is played, the system

closes PARTY automatically.

“BT” and “AUDIO” functions can be used

with the PARTY STREAMING function.

There are two kinds of PARTY

STREAMING-compatible equipment.

• PARTY host: Plays and sends music.

• PARTY guest: Plays music that is

received from PARTY host.

To use the system as a

PARTY guest

Select

[PARTY] in

[Music], then

select the PARTY host device icon.

To leave the PARTY, press OPTIONS,

then select [Leave PARTY].

This unit can be used as a PARTY host or

PARTY guest.

To close the PARTY, press OPTIONS,

then select [Close PARTY].

PARTY host

(This system)

Note

The sale and product lineup of products that are

compatible with the PARTY STREAMING

function differ depending on the area.

PARTY guest

Searching for video/

music information

PARTY guest

You can acquire content information using

Gracenote technology and search for

related information.

Prepare for PARTY STREAMING.

• Connect the system to a network

(page 21).

Connect the system to a network

(page 21).

• Connect equipment which is compatible

with the PARTY STREAMING function.

Insert a disc with content about

which you want to search.

You can perform a video search from a

BD-ROM or DVD-ROM, and a music

search from a CD-DA (music CD).

34^US

Press B/bto select

[Video] or

[Video

Available Options

Various settings and playback operations

are available by pressing OPTIONS. The

available items differ depending on the

situation.

[Music].

Press V/v to select

Search] or

[Music Search].

The content information (such as title,

cast, track, or artist), [Playback

History] and [Search History] are

displayed.

Common options

• [Playback History]

[Sound Mode]

Changes the sound mode setting (page 24).

Displays a list of previously played

BD-ROM/DVD-ROM/CD-DA

(music CD) titles. Select a title to

acquire content information.

• [Search History]

Displays a list of previous searches

performed via the [Video Search] or

[Music Search] function.

[Football]

Turns on or off the football mode (page 25).

[Repeat Setting]

Sets repeat playback.

[3D Menu]

[Simulated 3D]: Adjusts the simulated 3D

effect.

[3D Depth Adjustment]: Adjusts the depth of

3D images.

[2D Playback]: Sets playback to 2D image.

To search for further related

information

Select an item in the lists, then select the

[Play/Stop]

Starts or stops playback.

service for searches.

[Play from beginning]

Plays the item from the beginning.

Using the TV SideView

[Start PARTY]

TV SideView is a free mobile application

for the remote device (smartphone, etc). By

using the TV SideView with this system,

you can easily enjoy the system by the

operation on your remote device.

You can launch a service or application

directly from the remote device and view

the disc information during the disc

playback. The TV SideView also can be

used as a remote control and software

keyboard.

Starts a party with the selected source.

This item may not appear depending on the

source.

[Leave PARTY]

Leaves a party which the system is

participating in. The PARTY STREAMING

function continues among other participating

equipment.

[Close PARTY]

For PARTY host: Closes a party.

For PARTY guest: Closes a party which the

system is participating in. The PARTY

STREAMING function ends for all other

participating equipment.

Before you use the TV SideView device

with this system for the first time, be sure to

[Change Category]

Switches among the

and [Photo] category in “BD/DVD” (for

disc only) or “USB” function. This item only

available when the display list is available

for the category.

Follow the on-screen instructions on the

TV SideView device for registration.

[Video], [Music]

Note

The registration will be possible only when home

menu appears on the TV screen.

35^US

[Video] only

[Music] only

[A/V SYNC]

[Add Slideshow BGM]

Adjusts the time gap between picture and

Registers music files in the USB memory as

sound (page 37).

slideshow background music (BGM).

[3D Output Setting]

[Music Search]

Sets whether or not to output 3D video

Displays information on the audio CD

automatically.

(CD-DA) based on Gracenote technology.

[Video Settings]

• [Picture Quality Mode]: Selects the picture

settings for different lighting environments.

• [BNR]: Reduces the mosaic-like block

noise in the picture.

• [MNR]: Reduces minor noise around the

picture outlines (mosquito noise).

[Photo] only

[Slideshow]

Starts a slideshow.

[Slideshow Speed]

Changes the slideshow speed.

[Pause]

[Slideshow Effect]

Pauses playback.

Sets the effect when playing a slideshow.

[Top Menu]

[Slideshow BGM]

Displays the BD’s or DVD’s Top Menu.

• [Off]: Turns off the function.

• [My Music from USB]: Sets the music files

registered in [Add Slideshow BGM].

• [Play from Music CD]: Sets the tracks on

CD-DAs (music CDs).

[Menu/Popup Menu]

Displays the BD-ROM’s Pop-up Menu or

DVD’s menu.

[Title Search]

Searches for a title on BD-ROMs/DVD

VIDEOs and starts playback from the

beginning.

[Change Display]

Switches between [Grid View] and [List

View].

[Chapter Search]

Searches for a chapter and starts playback

from the beginning.

[Rotate Left]

Rotates the photo counterclockwise by

90 degrees.

[Audio]

Selects the audio format/track.

[Rotate Right]

Rotates the photo clockwise by 90 degrees.

[Subtitle]

[View Image]

Displays the selected picture.

Selects the subtitle language when

multilingual subtitles are recorded on

BD-ROMs/DVD VIDEOs.

[Angle]

Switches the viewing angles when multi-

angles are recorded on BD-ROMs/DVD

VIDEOs.

[IP Content Noise Reduction]

Adjusts the video quality for Internet

content.

[Video Search]

Displays information on the BD-ROM/

DVD-ROM based on Gracenote technology.

36^US

Adjusting the delay

betweenthepictureand

sound

Sound Adjustment

Selecting the Audio

Format, Multilingual

Tracks, or Channel

When the system is playing a BD/DVD

VIDEO recorded in multiple audio formats

(PCM, Dolby Digital, MPEG audio, or

DTS) or multilingual tracks, you can

change the audio format or language.

With a CD, you can select the sound from

the right or left channel and listen to the

sound of the selected channel through both

the right and left speakers.

(A/V SYNC)

When the sound does not match the

pictures on the TV screen, you can adjust

the delay between the picture and sound for

each function separately.

The setting method differs depending on

the function.

When other than the “BT” or

“TV” function is selected

Press OPTIONS.

The option menu appears on the TV

screen.

Press AUDIO repeatedly during

playback to select the audio signal

you want.

The audio information appears on the TV

screen.

Press V/v to select [A/V SYNC],

then press

Press B/b to adjust the delay,

then press

You can adjust from 0 ms to 300 ms in

25 ms increments.

x BD/DVD VIDEO

Depending on the BD/DVD VIDEO, the

When the “TV” function is

selected

option of language varies.

When 4 digits are displayed, they represent

a language code. See “Language Code

List” (page 66). When the same language is

displayed two or more times, the BD/DVD

VIDEO is recorded in multiple audio

formats.

Press OPTIONS.

“AV.SYNC” appears in the front panel

display.

Press

Press V/v to adjust the delay,

then press

or b.

x DVD-VR

The types of sound tracks recorded on a

disc are displayed.

Example:

You can adjust from 0 ms to 300 ms in

25 ms increments.

• [ Stereo]

• [ Stereo (Audio1)]

• [ Stereo (Audio2)]

• [ Main]

Press OPTIONS.

The option menu in the front panel

display turns off.

• [ Sub]

• [ Main/Sub]

37^US

Note

[

Stereo (Audio1)] and [ Stereo (Audio2)] do

Tuner

not appear if only one audio stream is recorded on

the disc.

Listening to the Radio

x CD

• [ Stereo]: The standard stereo sound.

• [ 1/L]: The sound of the left channel

(monaural).

• [ 2/R]: The sound of the right channel

(monaural).

• [ L+R]: The sound of both the left and

right channels output from each

individual speaker.

Press FUNCTION repeatedly

until “FM” appears in the front

panel display.

Select the radio station.

Automatic tuning

Hold down TUNING +/– until the auto

scanning starts.

[Auto Tuning] appears on the TV

screen. Scanning stops when the

system tunes in a station.

To cancel automatic tuning, press any

buttons.

Enjoying Multiplex

Broadcast Sound

(DUAL MONO)

Manual tuning

Press TUNING +/– repeatedly.

You can enjoy multiplex broadcast sound

when the system receives or plays a Dolby

Digital multiplex broadcast signal.

Press VOL +/– repeatedly to

adjust the volume.

Note

To receive a Dolby Digital signal, you need to

connect a TV or other equipment to the TV

(DIGITAL IN OPTICAL) jack with a optical

digital cord (pages 19, 20).

If your TV’s HDMI IN jack is compatible with

the Audio Return Channel function (pages 19,

50), you can receive a Dolby Digital signal via an

HDMI cable.

If an FM program is noisy

If an FM program is noisy, you can select

monaural reception. There will be no stereo

effect, but reception will improve.

Press OPTIONS.

The option menu appears on the TV

screen.

Press AUDIO repeatedly until the

signal you want appears in the front

panel display.

• “MAIN”: Sound of the main language

will be output.

• “SUB”: Sound of the sub language will

be output.

• “MN/SUB”: Mixed sound of both the

main and sub languages will be output.

Press V/v to select [FM Mode],

then press

Press V/v to select [Monaural],

then press

• [Stereo]: Stereo reception.

• [Monaural]: Monaural reception.

Tip

You can set [FM Mode] for each preset station

separately.

38^US

To turn off the radio

Press "/1.

Selecting a preset

station

Press FUNCTION repeatedly

until “FM” appears in the front

panel display.

Presetting radio

stations

The last received station is tuned in.

You can preset up to 20 stations. Before

tuning, make sure to turn down the volume

to minimum.

Press PRESET +/– repeatedly to

select the preset station.

The preset number and frequency

appear on the TV screen and front

panel display.

Each time you press the button, the

system tunes in one preset station.

Press FUNCTION repeatedly

until “FM” appears in the front

panel display.

Hold down TUNING +/– until the

auto scanning starts.

Tip

Scanning stops when the system tunes

in a station.

• You can select the preset station number

directly by pressing the number buttons.

• Each time you press DISPLAY, the

display in the front panel display changes

cyclically as follows:

Frequency tPreset number tDecoding

status*

* Appears when [Sound Effect] is set to

[Dolby Pro Logic], [DTS Neo:6

Cinema], or [DTS Neo:6 Music]

(page 48).

Press OPTIONS.

The option menu appears on the TV

screen.

Press V/v to select [Preset

Memory], then press

Press V/v to select the preset

number you want, then press

Repeat Steps 2 to 5 to store

other stations.

To change a preset number

Select the preset number you want by

pressing PRESET +/–, then perform the

procedure from Step 3.

39^US

System Audio Control

You can enjoy the sound from TV or other

equipment by a simple operation.

Other Operations

You can use the System Audio Control

function as follows:

Using the Control for

HDMI Function for

“BRAVIA” Sync

This function is available on TVs with the

“BRAVIA” Sync function.

By connecting Sony equipment that is

compatible with the Control for HDMI

function via an HDMI cable, operation is

simplified.

• When the system is turned on, the sound

of the TV or other equipment can be

output from the speakers of the system.

• When sound from the TV or other

equipment is output via the speakers of

the system, you can switch the sound to

output from the TV speakers by pressing

SPEAKERS TVyAUDIO.

• When sound from the TV or other

equipment is output via the speakers of

the system, you can adjust the volume

and turn off the sound of the system by

operating the TV.

Note

To use the “BRAVIA” Sync function, be sure to

turn on the system and all connected equipment

after completed the HDMI connection.

Audio Return Channel

You can enjoy TV sound via the system by

using just one HDMI cable. For details of

the setting, see “[Audio Return Channel]”

(page 50).

Control for HDMI - Easy

Setting

You can set the system’s [Control for

HDMI] function automatically by enabling

the corresponding setting on the TV.

For details about the Control for HDMI

function, see “[HDMI Settings]” (page 50)

Language Follow

When you change the language for the

on-screen display of the TV, the system’s

on-screen display language is also changed

after turning off and on the system.

System Power Off

You can turn the system off in sync with the

TV.

Note

The system does not turn off automatically while

playing music or when “FM” function is selected.

Setting the Speakers

[Speaker Settings]

One-Touch Play

To obtain optimum surround sound, set the

speakers’ distance from your listening

position. Then use the test tone to adjust the

balance of the speakers.

When you press N on the remote control,

the system and TV turn on, and the TV’s

input is switched to the HDMI input which

the system is connected.

Press HOME.

The home menu appears on the TV

screen.

40^US

Tip

Press B/b to select

Press V/v to select [Audio

Settings], then press

Press V/v to select [Speaker

Settings], then press

[Setup].

You can change the unit of measurement (feet or

meters) by pressing the color button (RED).

x [Level]

You can adjust the sound level of the

speakers. You can set the parameters from

–6.0 dB to +6.0 dB. Be sure to set [Test

Tone] to [On] for easy adjustment.

The [Select speaker layout.] display

appears.

Press V/v to select setting

according to your speakers

[Front Left/Right] 0.0 dB: Set the front

speaker level.

[Center] 0.0 dB: Set the center speaker

level.

[Surround Left/Right] 0.0 dB: Set the

surround speaker level.

[Subwoofer] 0.0 dB: Set the subwoofer

level.

placement, then press

• [Standard]: The surround speakers

are installed in the rear position.

• [All Front]: All speakers are installed

in the front position.

Note

The [Distance] and [Level] settings are reset

to default settings each time you change the

speaker layout setting.

x [Test Tone]

The speakers will emit a test tone to adjust

[Level].

Press V/v to select the item, then

press

[Off]: The test tone is not emitted from the

speakers.

Press V/v to adjust the

parameter.

[On]: The test tone is emitted from each

speaker in sequence while adjusting level.

When you select one of the [Speaker

Settings] items, the test tone is emitted

from each speaker in sequence.

Adjust the sound level as follows.

Press B/b and

settings.

Check the following settings.

to confirm the

x [Distance]

1 Set [Test Tone] to [On].

Be sure to set the parameters of the distance

from the listening position to the speakers.

You can set the parameters from 0 to

23 feet (0.0 to 7.0 meters).

2 Press V/v to select [Level], then

press

3 Press V/v to select the speaker type

you want, then press

[Front Left/Right] 10 ft/3.0 m: Set the front

speaker distance.

[Center] 10 ft/3.0 m: Set the center speaker

distance.

[Surround Left/Right] 10 ft/3.0 m: Set the

surround speaker distance.

[Subwoofer] 10 ft/3.0 m: Set the subwoofer

distance.

4 Press B/b to select the left or right

speaker, then press V/v to adjust the

level.

5 Press

6 Repeat Steps 3 to 5.

41^US

7 Press RETURN.

The system returns to the previous

display.

Deactivating the

Buttons on the Unit

8 Press V/v to select [Test Tone], then

press

(Child Lock)

9 Press V/v to select [Off], then press

You can deactivate the buttons on the unit

(except for "/1) for preventing

misoperation, such as child mischief.

Note

The test tone signals are not output from the

HDMI (OUT) jack.

Hold down x on the unit for more

than 5 seconds.

Tip

“LOCKED” appears in the front panel

display.

The child lock function is activated and the

buttons on the unit are locked. (You can

operate the system by using the remote

control.)

To adjust the volume of all the speakers at one

time, press VOL +/–.

To cancel, hold down x for more than

5 seconds until “UNLOCK” appears in the

front panel display.

Using the Sleep Timer

You can set the system to turn off at a

preset time, so you can fall asleep listening

to music. The time can be preset in intervals

of 10 minutes.

Note

If you operate the buttons on the unit while the

child lock function is on, “LOCKED” flashes in

the front panel display.

Press SLEEP.

Each time you press SLEEP, the minutes

display (the remaining time) in the front

panel display changes by 10 minutes.

Controlling Your TV

with the Supplied

Remote Control

By adjusting the remote control signal, you

can control your TV with the supplied

remote control.

When you set the sleep timer, the

remaining time appears every 5 minutes.

When the remaining time is less than

2 minutes, “SLEEP” flashes in the front

panel display.

To check the remaining

time

Note

Press SLEEP once.

When you replace the batteries of the remote

control, the code number may reset to the default

(SONY) setting. Set the appropriate code number

again.

To change the remaining

time

Press SLEEP repeatedly.

42^US

Preparing the remote

control for controlling

the TV

Browsing Websites

Prepare for Internet browsing.

Connect the system to a network

(page 21).

While holding down TV "/1, press

number buttons to enter your TV’s

manufacturer’s code (see the table).

Then release TV "/1.

Press HOME.

The home menu appears on the TV

screen.

Manufacturer

SONY

Code number

Press B/b to select

[Network].

01 (default)

Press V/v to select [Internet

Browser], then press

PANASONIC

SAMSUNG

SHARP

02, 06

The [Internet Browser] display

appears.

TOSHIBA

VIZIO

Note

Some websites may not display correctly, or not

function.

If the setting is unsuccessful, the currently

registered code is not changed. Re-enter the

code number.

If more than one code number is listed, try

entering them one at a time until you find

the code that works with your TV.

To enter a URL

Select [URL entry] from the options menu.

Enter the URL using the software

keyboard, then select [Enter].

To set the default start page

While the page you want to set is displayed,

select [Set as start page] from the options

menu.

Saving Power in

Standby Mode

Check that you have made the following

settings:

– [Control for HDMI] in [HDMI Settings]

is set to [Off] (page 50).

– [Quick Start Mode] is set to [Off]

(page 50).

To return to the previous

page

Select [Previous page] from the options

menu.

When the previous page does not appear

even if you select [Previous page], select

[Window List] from the options menu and

select the page you want to return to from

the list.

– [Remote Start] in [Network Settings] is

set to [Off] (page 51).

To quit Internet Browser

Press HOME.

43^US

Internet Browser

display

Available options

Various settings and operations are

available by pressing OPTIONS.

The available items differ depending on the

situation.

You can check website information by

pressing DISPLAY. The display

information differs depending on the

website and page status.

[Browser Setup]

Displays the Internet Browser settings.

• [Zoom]: Increases or decreases the size of

the displayed contents.

• [JavaScript Setup]: Sets whether to enable

or disable JavaScript.

• [Cookie Setup]: Sets whether or not to

accept browser cookies.

• [SSL Alarm Display]: Sets whether to

enable or disable SSL.

[Window List]

Displays a list of all current opened websites.

Allows you to return to a previous displayed

website by selecting the window.

A Page title

B Page address

C Cursor

[Bookmark List]

Displays the bookmark list.

Move by pressing B/V/v/b. Place the

cursor on the link you want to view,

then press . The linked website is

displayed.

[URL entry]

Allows you to enter a URL when the

software keyboard is displayed.

[Previous page]

Moves to a previous displayed page.

D SSL icon

Appears when the linked URL is

secured.

[Next page]

Moves to the previous displayed next page.

E Signal strength indicator

Appears when the system is connected

to a wireless network.

[Cancel loading]

Stops loading a page.

[Reload]

Reloads the same page.

F Progress bar/Loading icon

Appears when the page is being read,

or during file download/transfer.

[Add to Bookmark]

Adds the current displayed website to the

bookmark list.

G Text input field

[Set as start page]

Sets the current displayed website as the

default start page.

Press , then choose [Input] from the

options menu to open the software

keyboard.

[Open in new window]

Opens a link in a new window.

H Scroll bar

Press B/V/v/b to move the page

display left, up, down, or right.

[Character encoding]

Sets the character encoding system.

44^US

[Display certificate]

Displays server certificates sent from pages

that support SSL.

Settings and Adjustments

[Input]

Displays the software keyboard to enter

characters while browsing a website.

Using the Setup Display

[Break]

You can make various adjustments to items

such as picture and sound.

The default settings are underlined.

Moves the cursor to the next line in the text

input field.

[Delete]

Note

Erases one character on the left side of the

cursor during text input.

Playback settings stored in the disc take priority

over the Setup Display settings. Therefore, some

of the functions may not be performed.

Press HOME.

The home menu appears on the TV

screen.

Press B/b to select

[Setup].

Press V/v to select the setup

category icon, then press

Icon

Explanation

[Network Update]

(page 46)

Updates the software of the

system.

[Screen Settings]

(page 46)

Makes the screen settings

according to the type of

TV.

[Audio Settings]

(page 48)

Makes the audio settings

according to the type of

connecting jacks.

[BD/DVD Viewing

Settings] (page 49)

Makes detailed settings for

BD/DVD playback.

45^US

Icon

Explanation

[Parental Control

Settings] (page 49)

Makes detailed settings for

the Parental Control

function.

[Screen Settings]

x [3D Output Setting]

[Auto]: Normally select this.

[Off]: Select this to display all contents in

2D.

[System Settings]

(page 50)

Makes the system-related

settings.

x [TV Screen Size Setting for 3D]

Sets the screen size of your 3D-compatible

TV.

[Network Settings]

(page 51)

Makes detailed settings for

Internet and network.

[Easy Network Settings]

(page 52)

Runs [Easy Network

Settings] to make the basic

network settings.

x [TV Type]

[16:9]: Select this when connecting to a

wide-screen TV or a TV with a wide-mode

function.

[4:3]: Select this when connecting to a 4:3

screen TV without a wide-mode function.

[Resetting] (page 52)

Resets the system to the

factory settings.

x [Screen Format]

[Full]: Select this when connecting to a TV

with a wide-mode function. Displays a 4:3

screen picture in 16:9 aspect ratio even on

a wide-screen TV.

[Normal]: Changes the picture size to fit

the screen size with the original picture

aspect ratio.

[Network Update]

By updating your software to the latest

version, you can take advantage of the

newest functions.

For information about update functions,

refer to the following website:

http://www.sony.com/blurayhtsupport/

During a software update, “UPDATE”

appears in the front panel display. After the

update completes, the unit automatically

turns off.

While the updating operation is in progress,

do not turn on or off the unit, or operate the

unit or TV. Wait for the software update to

complete.

46^US

x [DVD Aspect Ratio]

x [BD-ROM 24p Output]

[Letter Box]: Displays a wide picture with

black bands on the top and bottom.

[Auto]: Outputs 24p video signals only

when you connect a 1080/24p-compatible

TV via an HDMI connection and the

[Output Video Resolution] is set to [Auto]

or [1080p].

[On]: Select this when your TV is

compatible with 1080/24p video signals.

[Off]: Select this when your TV is not

compatible with 1080/24p video signals.

[Pan & Scan]: Displays a full-height

picture on the entire screen, with trimmed

sides.

x [DVD-ROM 24p Output]

[Auto]: Outputs 24p video signals only

when you connect a 1080/24p-compatible

TV via an HDMI connection and the

[Output Video Resolution] is set to [Auto]

or [1080p].

[Off]: Select this when your TV is not

compatible with 1080/24p video signals.

x [Cinema Conversion Mode]

[Auto]: Normally select this. The unit

automatically detects whether the material

is video-based or film-based, and switches

to the appropriate conversion method.

[Video]: The conversion method suited for

video-based material will always be

selected regardless of the material.

x [YCbCr/RGB (HDMI)]

[Auto]: Automatically detects the type of

external equipment, and switches to the

matching color setting.

[YCbCr (4:2:2)]: Outputs YCbCr 4:2:2

video signals.

[YCbCr (4:4:4)]: Outputs YCbCr 4:4:4

video signals.

[RGB]: Select this when connecting to an

equipment with an HDCP compliant DVI

jack.

x [Output Video Resolution]

[Auto]: Outputs video signal according to

the resolution of the TV or connected

equipment.

[Original Resolution]: Outputs video signal

according to the resolution recorded on the

disc. (When the resolution is lower than SD

resolution, it is scaled up to SD resolution.)

[480i/576i]*, [480p/576p]*, [720p],

[1080i], [1080p]: Outputs video signal

according to the selected resolution setting.

x [HDMI Deep Color Output]

[Auto]: Normally select this.

[16bit], [12bit], [10bit]: Outputs 16bit/

12bit/10bit video signals when the

connected TV is compatible with Deep

Color.

* If the color system of your disc is NTSC, the

video signals resolution can be converted to

[480i] and [480p] only.

[Off]: Select this when the picture is

unstable or colors appear unnatural.

47^US

x [Pause Mode] (BD/DVD VIDEO/

DVD-R/DVD-RW only)

[Auto]: The picture, including subjects that

move dynamically, is output with no jitter.

Normally select this position.

[Frame]: The picture, including subjects

that do not move dynamically, is output in

high resolution.

x [Audio Output]

You can select the output method where the

audio signal is output.

[Speaker]: Outputs multi-channel sound

from the system’s speakers only.

[Speaker + HDMI]: Outputs multi-channel

sound from the system’s speakers and

2-channel linear PCM signals from the

HDMI (OUT) jack.

[HDMI]: Outputs sound from the HDMI

(OUT) jack only. Sound format depends on

the connected equipment.

[Audio Settings]

Note

• When [Control for HDMI] is set to [On]

(page 50), [Audio Output] is set to [Speaker +

HDMI] automatically and this setting cannot be

changed.

• When [Audio Output] is set to [HDMI], the

output signal format for the “TV” function is

2-channel linear PCM.

x [BD Audio MIX Setting]

[On]: Outputs the audio obtained by mixing

the interactive audio and secondary audio

to the primary audio.

[Off]: Outputs the primary audio only.

x [Audio DRC]

You can compress the dynamic range of the

sound track.

x [Sound Effect]

You can turn on or off the system’s sound

effects (SOUND MODE setting (page 24)).

For a 2-channel source, you can select

[Dolby Pro Logic], [DTS Neo:6 Cinema],

or [DTS Neo:6 Music] to simulate surround

sound.

[Auto]: Performs playback at the dynamic

range specified by the disc (BD-ROM

only).

[On]: The system reproduces the sound

track with the kind of dynamic range that

the recording engineer intended.

[Off]: No compression of dynamic range.

[Sound Mode On]: Enables the surround

effect of the sound mode (page 24) and

Football mode (page 25).

[Dolby Pro Logic]: The system simulates

surround sound from 2-channel sources

and outputs sound from all speakers

(5.1 channel) (Dolby Pro Logic decoding).

[DTS Neo:6 Cinema]/[DTS Neo:6 Music]:

The system simulates surround sound from

2-channel sources and produces multi-

channel sound (DTS Neo:6 Cinema/DTS

Neo:6 Music mode decoding).

x [Attenuate - AUDIO]

Distortion may occur when you listen to an

equipment connected to the AUDIO IN

(L/R) jacks. You can prevent distortion by

attenuating the input level on the unit.

[On]: Attenuates the input level. The output

level will decrease at this setting.

[Off]: Normal input level.

[2ch Stereo]: This system outputs the sound

from the front left/right speakers and

subwoofer only. Multi-channel surround

formats are downmixed to 2-channel.

48^US

[Off]: The sound effects are disabled. You

can hear sound as it is recorded.

x [Subtitle Language]

You can select the default subtitle language

for BD-ROMs or DVD VIDEOs.

When you select [Select Language Code],

the display for entering the language code

appears. Enter the code for your language

by referring to “Language Code List”

(page 66).

x [Speaker Settings]

To obtain optimum surround sound, set the

speakers. For details, see “Setting the

Speakers” (page 40).

x [Bluetooth AUDIO - AAC]

You can enable and disable AAC output.

x [BD Hybrid Disc Playback Layer]

[BD]: Plays BD layer.

[DVD/CD]: Plays DVD or CD layer.

[On]: Outputs AAC if the Bluetooth device

supports AAC.

[Off]: Outputs SBC.

x [BD Internet Connection]

[Allow]: Normally select this.

[Do not allow]: Prohibits Internet

connection.

Note

You can enjoy high quality sound if the AAC is

enabled. In case you cannot listen to AAC sound

from your device, select [Off].

[BD/DVD Viewing

Settings]

[Parental Control

Settings]

x [BD/DVD Menu Language]

You can select the default menu language

for BD-ROMs or DVD VIDEOs.

When you select [Select Language Code],

the display for entering the language code

appears. Enter the code for your language

by referring to “Language Code List”

(page 66).

x [Password]

Set or change the password for the Parental

Control function. A password allows you to

set a restriction on BD-ROM, DVD

VIDEO, or Internet video playback. If

necessary, you can differentiate the

restriction levels for BD-ROMs and DVD

VIDEOs.

x [Audio Language]

x [Parental Control Area Code]

Playback of some BD-ROMs or DVD

VIDEOs can be limited according to the

geographic area. Scenes may be blocked or

replaced with different scenes. Follow the

on-screen instructions and enter your four-

digit password.

You can select the default track language

for BD-ROMs or DVD VIDEOs.

When you select [Original], the language

given priority in the disc is selected.

When you select [Select Language Code],

the display for entering the language code

appears. Enter the code for your language

by referring to “Language Code List”

(page 66).

49^US

[Audio Return Channel]

x [BD Parental Control]/[DVD

Parental Control]/[Internet Video

Parental Control]

By setting Parental Control, scenes can be

blocked or replaced with different scenes.

Follow the on-screen instructions and enter

your four-digit password.

This function is available when you

connect the system to a TV’s HDMI IN

jack that is compatible with the Audio

Return Channel function and [Control for

HDMI] is set to [On].

[Auto]: The system can receive the digital

audio signal of the TV automatically via an

HDMI cable.

[Off]: Off.

x [Internet Video Unrated]

[Allow]: Allows the playback of unrated

Internet videos.

x [Quick Start Mode]

[On]: Shortens the startup time from

standby mode. You can operate the system

quickly after turning it on.

[Block]: Blocks the playback of unrated

Internet videos.

[Off]: The default setting.

[System Settings]

x [Auto Display]

[On]: Automatically displays information

on the screen when changing the viewing

titles, picture modes, audio signals, etc.

[Off]: Displays information only when you

press DISPLAY.

x [OSD Language]

You can select the language you want for

the system on-screen display.

x [Main Unit illumination]

x [Screen Saver]

[On]: The front panel display is always

turned on and the brightness of the LED

indicator is the maximum.

[On]: Turns on the screen saver function.

[Off]: Off.

[Auto]: The front panel display is turned

off and the brightness of LED indicator is

reduced automatically if you do not operate

the system for about 10 seconds.

x [Software Update Notification]

[On]: Sets the system to inform you of

latest software version information

(page 46).

[Off]: Off.

x [HDMI Settings]

[Control for HDMI]

x [Gracenote Settings]

[On]: Turns on the [Control for HDMI]

function. You can operate mutually

between equipment that are connected with

an HDMI cable.

[Auto]: Automatically downloads disc

information when you stop playback of the

disc. To download, the system must be

connected to the network.

[Manual]: Downloads disc information

when [Video Search] or [Music Search] is

selected.

[Off]: Off.

50^US

x [System Information]

x [Renderer Options]

You can display the system’s software

version information and the MAC address.

[Auto Access Permission]: Sets whether or

not to allow automatic access from a newly

detected DLNA controller.

[Smart Select]: Allows a Sony DLNA

controller to find the system as the target

equipment to operate by using the infrared

ray. You can set this function to on or off.

[Renderer Name]: Displays the system’s

name as it is listed on other DLNA devices

on the network.

x [Software License Information]

You can display the Software License

Information.

[Network Settings]

x [Renderer Access Control]

Sets whether or not to accept commands

from DLNA controllers.

x [Internet Settings]

Connect the system to the network

beforehand. For details, see “Step 3:

Preparing for Network Connection”

(page 21).

x [PARTY Auto Start]

[On]: Starts a PARTY or joins an existing

PARTY at the request of a networked

device compatible with the PARTY

STREAMING function.

[Wired Setup]: Select this when you

connect to a broadband router using a LAN

cable.

[Wireless Setup(built-in)]: Select this when

you use the built-in wireless LAN of the

system for wireless network connection.

[Off]: Off.

x [Registered Remote Devices]

Displays a list of your registered remote

devices.

Tip

For further details, visit the following website and

check the FAQ:

Note

http://www.sony.com/blurayhtsupport/

To use this function, be sure to perform the

software update (page 46).

x [Network Connection Status]

Displays the current network connection

status.

x [Remote Start]

[On]: Allows turn on the system by a

device linked via network when the system

is in standby mode.

[Off]: The system cannot be turned on by a

device linked via network.

x [Network Connection

Diagnostics]

You can run the network diagnostic to

check if the network connection has been

made properly.

x [Connection Server Settings]

Sets whether or not to display the

connected DLNA server.

51^US

[Easy Network

Settings]

Runs [Easy Network Settings] to make the

basic network settings. Follow the on-

screen instructions.

Additional Information

Precautions

On safety

• Should any solid object or liquid fall into

the cabinet, unplug the system and have it

checked by qualified personnel before

operating it any further.

• Do not touch the AC power cord (mains

lead) with wet hands. Doing so may cause

an electric shock.

[Resetting]

x [Reset to Factory Default Settings]

You can reset the system settings to the

factory default by selecting the group of

settings. All the settings within the group

will be reset.

On power sources

If you are not going to use the system for a

long time, be sure to disconnect the system

from the wall outlet. To disconnect the AC

power cord (mains lead), grasp the plug

itself; never pull the cord.

x [Initialize Personal Information]

You can erase your personal information

stored in the system.

On placement

• Place the system in a location with

adequate ventilation to prevent heat

build-up in the system.

• Although the unit heats up during

operation, this is not a malfunction. If you

continuously use this unit at a large

volume, the cabinet temperature of the

top, side and bottom rises considerably.

To avoid burning yourself, do not touch

the cabinet.

• Do not place the unit on a soft surface

(rugs, blankets, etc.) that might block the

ventilation holes.

• Do not install the system near heat

sources such as radiators, air ducts, or in

a place subject to direct sunlight,

excessive dust, mechanical vibration, or

shock.

• Do not install the system in an inclined

position. It is designed to be operated in a

horizontal position only.

52^US

• Keep the system and discs away from

components with strong magnets, such as

microwave ovens, or large loudspeakers.

• Do not place heavy objects on the system.

• Do not place metal objects in front of the

front panel. It may limit reception of

radio waves.

• Do not place the system in a place where

medical equipment is in use. It may cause

a malfunction of medical equipment.

• If you use a pacemaker or other medical

device, consult your physician or the

manufacturer of your medical device

before using the wireless LAN function.

On replacement of parts

In the events that this system is repaired,

repaired parts may be retained for reuse or

recycling purposes.

On your TV’s color

If the speakers cause the color irregularity

on your TV screen, turn off the TV then

turn it on after 15 to 30 minutes. If color

irregularity persist, place the speakers

further away from the TV set.

IMPORTANT NOTICE

Caution: This system is capable of

holding a still video image or on-screen

display image on your TV screen

indefinitely. If you leave the still video

image or on-screen display image

displayed on your TV for an extended

period of time, you risk permanent

damage to your TV screen. Plasma

display panel televisions and projection

televisions are especially susceptible to

this.

On operation

If the system is brought directly from a cold

to a warm location, or is placed in a very

damp room, moisture may condense on the

lenses inside the unit. Should this occur, the

system may not operate properly. In this

case, remove the disc and leave the system

turned on for about half an hour until the

moisture evaporates.

On adjusting volume

On moving the system

Do not turn up the volume while listening

to a section with very low level inputs or no

audio signals. If you do, the speakers may

be damaged when a peak level section is

suddenly played.

Before moving the system, make sure that

there is no disc inserted, and disconnect the

AC power cord (mains lead) from the wall

outlet (mains).

On cleaning

Clean the cabinet, panel, and controls with

a soft cloth slightly moistened with a mild

detergent solution. Do not use any type of

abrasive pad, scouring powder or solvent

such as alcohol or benzine.

On cleaning discs, disc/lens

cleaners

Do not use cleaning discs or disc/lens

cleaners (including wet or spray types).

These may cause the apparatus to

malfunction.

53^US

• This unit supports security functions that

comply with the Bluetooth specification

to ensure secure connection during

communication using Bluetooth

technology. However, this security may

be insufficient depending on the setting

contents and other factors, so always be

careful when performing communication

using Bluetooth technology.

• Sony cannot be held liable in any way for

damages or other loss resulting from

information leaks during communication

using Bluetooth technology.

• Bluetooth communication is not

necessarily guaranteed with all Bluetooth

devices that have the same profile as this

receiver.

On Bluetooth

communication

• Bluetooth devices should be used within

approximately 10 meters (33 feet)

(unobstructed distance) of each other.

The effective communication range may

become shorter under the following

conditions.

– When a person, metal object, wall or

other obstruction is between the devices

with a Bluetooth connection

– Locations where a wireless LAN is

installed

– Around microwave ovens that are in

use

– Locations where other electromagnetic

waves occur

• Bluetooth devices connected with this

unit must comply with the Bluetooth

specification prescribed by the Bluetooth

SIG, Inc., and must be certified to

comply. However, even when a device

complies with the Bluetooth

specification, there may be cases where

the characteristics or specifications of the

Bluetooth device make it impossible to

connect, or may result in different control

methods, display or operation.

• Noise may occur or the audio may cut off

depending on the Bluetooth device

connected with this unit, the

communications environment, or

surrounding conditions.

• Bluetooth devices and wireless LAN

(IEEE 802.11b/g) use the same frequency

band (2.4 GHz). When using your

Bluetooth device near a device with

wirelessLANcapability, electromagnetic

interference may occur. This could result

in lower data transfer rates, noise, or

inability to connect. If this happens, try

the following remedies:

– Use this unit at least 10 meters (33 feet)

away from the wireless LAN device.

– Turn off the power to the wireless LAN

equipment when using your Bluetooth

device within 10 meters (33 feet).

– Install this unit and Bluetooth device as

closer to each other as possible.

• The radio waves broadcast by this unit

may interfere with the operation of some

medical devices. Since this interference

may result in malfunction, always turn off

the power on this unit and Bluetooth

device in the following locations:

– In hospitals, on trains, in airplanes, at

gas stations, and any place where

flammable gasses may be present

– Near automatic doors or fire alarms

If you have any questions or problems

concerning your system, please consult

your nearest Sony dealer.

54^US

Notes about Discs

Troubleshooting

If you experience any of the following

difficulties while using the system, use this

troubleshooting guide to help remedy the

problem before requesting repairs. Should

any problem persist, consult your nearest

Sony dealer.

On handling discs

• To keep the disc clean, handle the disc by

its edge. Do not touch the surface.

• Do not stick paper or tape on the disc.

General

The power does not turn on.

t Check that the AC power cord (mains

lead) is connected securely.

• Do not expose the disc to direct sunlight

or heat sources such as hot air ducts, or

leave it in a car parked in direct sunlight

as the temperature may rise considerably

inside the car.

The remote control does not function.

t The distance between the remote

control and the unit is too far.

t The batteries in the remote control are

weak.

• After playing, store the disc in its case.

On cleaning

• Before playing, clean the disc with a

cleaning cloth.

Wipe the disc from the center out.

The disc tray does not open and you

cannot remove the disc even after you

press Z.

t Try the following:

1 Hold down N and Z on the unit

for more than 5 seconds to open the

disc tray.

2 Remove the disc.

3 Disconnect the AC power cord

(mains lead) from the wall outlet

(mains), then reconnect after

several minutes.

• Do not use solvents such as benzine,

thinner, commercially available cleaners,

or anti-static spray intended for vinyl

LPs.

This system can only play a standard

circular disc. Using neither standard nor

circular discs (e.g., card, heart, or star

shape) may cause a malfunction.

The system does not work normally.

t Disconnect the AC power cord (mains

lead) from the wall outlet (mains), then

reconnect after several minutes.

Do not use a disc that has a commercially

available accessory attached, such as a

label or ring.

55^US

appears without any messages on

the entire TV screen.

Messages

t Contact your nearest Sony dealer or

local authorized Sony service facility.

[A new software version is available.

Please go to the “Setup” section of

the menu and select “Network

Update” to perform the update.]

appears on the TV screen.

t See [Network Update] (page 46) to

update the system to a latest software

version.

Picture

There is no picture or the picture is

not output correctly.

t Check the output method on your

system (page 19).

“PRTECT”, “PUSH” and “POWER”

appear alternately in the front panel

display.

t Press "/1 to turn off the system, and

check the following items after

“STBY” disappears.

t Hold down N and VOL – on the unit

for more than 5 seconds to reset the

video output resolution to the lowest

resolution.

t For BD-ROMs, check the [BD-ROM

24p Output] settings in [Screen

Settings] (page 47).

• Are you using only the supplied

speakers?

• Is anything blocking the ventilation

holes of the system?

There is no picture when you make an

HDMI cable connection.

t The unit is connected to an input

device that is not HDCP (High-

bandwidth Digital Content Protection)

compliant (“HDMI” in the front panel

does not light up) (page 19).

• After checking the above items and

fixing any problems, turn on the

system. If the cause of the problem

cannot be found even after checking

all the above items, consult your

nearest Sony dealer.

The dark area of the picture is too

dark/the bright area is too bright or

unnatural.

t Set [Picture Quality Mode] to

[Standard] (default) (page 36).

“LOCKED” appears in the front panel

display.

t Set the child lock function to off

(page 42).

Picture noise appears.

“D. LOCK” appears in the front panel

display.

t Clean the disc.

t If the picture output from your system

goes through your VCR to get to your

TV, the copy-protection signal applied

to some BD/DVD programs could

affect picture quality. If you still

experience problems even when you

connect your unit directly to your TV,

try connecting your unit to the other

input jacks.

t Contact your nearest Sony dealer or

local authorized Sony service facility.

“Exxxx” (x is a number) appears in

the front panel display.

t Contact your nearest Sony dealer or

local authorized Sony service facility

and give the error code.

56^US

An image is not displayed on the

entire TV screen.

The system does not output sound of

TV programs correctly when

connected to a set-top box.

t Set [Audio Return Channel] in [HDMI

Settings] of [System Settings] to [Off]

(page 50).

t Check the setting of [TV Type] in

[Screen Settings] (page 46).

t The aspect ratio on the disc is fixed.

Color irregularity occurs on the TV

screen.

t If the speakers are used with a CRT-

based TV or projector, install the

speakers at least 0.3 meters (1 foot)

from the TV set.

t Check the connections (page 20).

Severe hum or noise is heard.

t Move your audio equipment away

from the TV.

t Clean the disc.

t If the color irregularity persists, turn

off the TV set once, then turn it on after

15 to 30 minutes.

t Make sure that no magnetic object

(magnetic latch on a TV stand, health

care device, toy, etc.) is placed near the

speakers.

The sound loses stereo effect when

you play a CD.

t Select stereo sound by pressing

AUDIO (page 37).

The sound outputs from the center

speaker only.

t Depending on the disc, the sound may

output from the center speaker only.

Sound

There is no sound.

No sound or only a very low-level

sound is heard from the surround

speakers.

t Check the speaker connections and

settings (pages 18, 40).

t The speaker cords are not connected

securely.

t Check the speaker settings (page 40).

There is no sound from the TV via the

HDMI (OUT) jack when using the

Audio Return Channel function.

t Set [Control for HDMI] in [HDMI

Settings] of [System Settings] to [On]

(page 50). Also, set [Audio Return

Channel] in [HDMI Settings] of

[System Settings] to [Auto] (page 50).

t Make sure that your TV is compatible

with the Audio Return Channel

function.

t Check the sound mode setting

(page 24).

t Depending on the source, the effect of

the surround speakers may be less

noticeable.

t A 2-channel source is being played.

Distortion occurs in the sound of a

connected equipment.

t Reduce the input level for the

connected equipment by setting

[Attenuate - AUDIO] (page 48).

t Make sure that an HDMI cable is

connected to a jack on your TV that is

compatible with the Audio Return

Channel function.

A sudden loud music is heard.

t The build-in sound demonstration is

activated. Press VOL – to reduce the

volume or press x to stop the

demonstration.

57^US

Playback does not start from the

resume point where you last stopped

playing.

t The resume point may be cleared from

memory depending on the disc when

• you open the disc tray.

Tuner

Radio stations cannot be tuned in.

t Check that the antenna (aerial) is

connected securely. Adjust the antenna

(aerial).

t The signal strength of the stations is

too weak (when tuning in with

automatic tuning). Use manual tuning.

• you disconnect the USB device.

• you play other content.

• you turn off the unit.

The language for the soundtrack/

subtitle or angles cannot be changed.

t Try using the BD’s or DVD’s menu.

t Multi-lingual tracks/subtitles or multi-

angles are not recorded on the BD or

DVD being played.

Playback

The disc does not play.

t The region code on the BD/DVD does

not match the system.

t Moisture has condensed inside the unit

and may cause damage to the lenses.

Remove the disc and leave the unit

turned on for about half an hour.

t The system cannot play a recorded disc

that is not correctly finalized

Bonus contents or other data that are

contained in a BD-ROM cannot be

played.

t Try the following:

1 Remove the disc.

(page 60).

2 Turn the system off.

3 Remove and reconnect the USB

device (page 28).

4 Turn the system on.

5 Insert the BD-ROM with

BONUSVIEW/BD-LIVE.

File names are not displayed

correctly.

t The system can only display ISO

8859-1 compliant character formats.

Other character formats may be

displayed differently.

t Depending on the writing software

used, the input characters may be

displayed differently.

USB device

The USB device is not recognized.

t Try the following:

1 Turn the system off.

2 Remove and reconnect the USB

device.

A disc does not start playing from the

beginning.

t Resume play has been selected. Press

OPTIONS and select [Play from

3 Turn the system on.

t Make sure that the USB device is

securely connected to the (USB)

port.

beginning], then press

t Check if the USB device or a cable is

damaged.

t Check if the USB device is on.

58^US

t If the USB device is connected via a

USB hub, disconnect it and connect

the USB device directly to the unit.

• The connected equipment’s setting

for the [Control for HDMI] function

is correct.

BRAVIA Internet Video

Network connection

The picture/sound is poor/certain

programs display with a loss of detail,

especially during fast-motion or dark

scenes.

t Picture/sound quality may be poor

depending on Internet content

providers.

The system cannot connect to the

network.

t Check the network connection

(page 21) and the network settings

(page 51).

Wireless LAN

connection

t Picture/sound quality may be

improved by changing the connection

speed. Sony recommends a connection

speed of at least 2.5 Mbps for standard-

definition video and 10 Mbps for high-

definition video.

You cannot connect your PC to the

Internet after [Wi-Fi Protected Setup

(WPS)] is performed.

t The wireless settings of the router may

change automatically if you use the

Wi-Fi Protected Setup function before

adjusting the settings of the router. In

this case, change the wireless settings

of your PC accordingly.

t Not all videos contain sound.

The picture is small.

t Press V to zoom in.

“BRAVIA” Sync

([Control for HDMI])

The system cannot connect to the

network or the network connection is

unstable.

t Check if the wireless LAN router is on.

t Check the network connection

(page 21) and the network settings

(page 51).

t Depending on the usage environment,

including the wall material, radio wave

reception conditions, or obstacles

between the system and the wireless

LAN router, the possible

The [Control for HDMI] function does

not work (“BRAVIA” Sync).

t Check that [Control for HDMI] is set

to [On] (page 50).

t If you change the HDMI connection,

turn the system off and on again.

t If power failure occurs, set [Control

for HDMI] to [Off], then set [Control

for HDMI] to [On] (page 50).

t Check the following and refer to the

operating instructions supplied with

the equipment.

communication distance may be

shortened. Move the system and the

wireless LAN router closer to each

other.

• The connected equipment is

compatible with the [Control for

HDMI] function.

59^US

t Devices that use a 2.4 GHz frequency

band, such as a microwave, Bluetooth,

or digital cordless device, may

interrupt communication. Move the

unit away from such devices, or turn

off such devices.

t The wireless LAN connection may be

unstable depending on the usage

environment, especially while using

the Bluetooth function of the system.

In this case, adjust the usage

There is no sound.

t Make sure this system is not too far

from the Bluetooth device, or this

system is not receiving interference

from a Wi-Fi network, other 2.4 GHz

wireless device, or microwave oven.

t Check that the Bluetooth connection is

made properly between this system

and the Bluetooth device.

t Pair this system and the Bluetooth

device again.

t Keep the system away from metal

objects or surfaces.

environment.

The wireless router you want is not

shown in the wireless network list.

t Press RETURN to return to the

previous screen, and try [Wireless

Setup(built-in)] again. If the wireless

router you want is still not detected,

select [Add a new address.] from the

network list, then select [Manual

Registration] to input a network name

(SSID) manually.

t Make sure “BT” function is selected.

t Adjust the volume of the Bluetooth

device first, if the volume level is still

too low, adjust the volume level on the

unit.

The sound skips or fluctuates, or the

connection is lost.

t The unit and the Bluetooth device are

too far apart.

t If there are obstacles between the unit

and your Bluetooth device, remove or

avoid the obstacles.

Bluetooth device

t If there is equipment that generates

electromagnetic radiation, such as a

wireless LAN, other Bluetooth device,

or a microwave oven nearby, move

them away.

Pairing cannot be done.

t Move the Bluetooth device closer to

the unit.

t Pairing may not be possible if other

Bluetooth devices are present around

the unit. In this case, turn off the other

Bluetooth devices.

t Delete the system from your Bluetooth

device and perform pairing again

(page 29).

Playable Discs

Blu-ray Disc

BD-ROM

Connecting cannot be done.

t The pairing registration information

has been erased. Perform the pairing

operation again (page 29).

BD-R/BD-RE

DVD

DVD-ROM

DVD-R/DVD-RW

DVD+R/DVD+RW

CD-DA (Music CD)

CD-ROM

CD-R/CD-RW

60^US

Since Blu-ray Disc specifications are new and

evolving, some discs may not be playable

depending on the disc type and version. Also,

the audio output differs depending on the

source, connected output jack, and selected

audio settings.

BD-RE: Ver.2.1

BD-R: Ver.1.1, 1.2, 1.3 including organic

pigment type BD-R (LTH type)

BD-Rs recorded on a PC cannot be played if

postscripts are recordable.

A CD or DVD disc will not play if it has not

been correctly finalized. For more information,

refer to the operating instructions supplied with

the recording device.

Note on double-layer

BDs/DVDs

The playback picture and sound may be

momentarily interrupted when the layers

switch.

Region code (BD-ROM/DVD

VIDEO only)

Your system has a region code printed on

the bottom of the unit and will only play a

BD-ROM/DVD VIDEO (playback only)

labeled with identical region codes or

ALL

Discs that cannot be played

• BDs with cartridge

• BDXLs

• DVD-RAMs

Playable Types of Files

Video

• HD DVDs

• DVD Audio discs

• PHOTO CDs

• Data part of CD-Extras

• Super VCDs

Video Codec

MPEG-1 Video

MPEG-2 Video

Container Extension

.mpg, .mpeg

.m2ts, .mts

.avi

• Audio material side on DualDiscs

• For U.S.A. and Canada models: A disc

recorded in a color system other than

NTSC, such as PAL (This system

conforms to the NTSC color system.)

Xvid

AVI

MKV

.mkv

MPEG4/AVC

.mkv

MP4

.mp4, .m4v

.m2ts, .mts

.mov

Notes on discs

This product is designed to play back discs

that conform to the Compact Disc (CD)

standard.

Quick

Time

DualDiscs and some music discs encoded

with copyright protection technologies do

not conform to the Compact Disc (CD)

standard. Therefore, these discs may not be

compatible with this product.

3gpp/

3gpp2

.3gp, .3g2,

.3gpp, .3gp2

VC1

.m2ts, .mts

.wmv, .asf

.mov

WMV9

ASF

Motion JPEG

Quick

Time

Note on playback

operations of a BD/DVD

AVI

.avi

Some playback operations of a BD/DVD

may be intentionally set by software

producers. Since this system plays a

BD/DVD according to the disc contents the

software producers designed, some

playback features may not be available.

Video Format

Container Extension

*1*7

AVCHD

AVCHD Format

Folder

61^US

Music

Note

• Some files may not play depending on the file

format, the file encoding, the recording

condition, or DLNA server condition.

• Some files edited on a PC may not play.

• Some files may not be able to perform fast

forward or fast reverse function.

Audio Codec

Extension

MP3 (MPEG-1 Audio .mp3, .mka

Layer III)

AAC

.m4a, .aac , .mka

.wma

WMA9 Standard

LPCM

• The system does not play coded files such as

DRM and Lossless.

.wav, .mka

• The system can recognize the following files or

folders in BDs, DVDs, CDs and USB devices:

– up to folders in the 9th layer (including the

root folder)

FLAC

.flac, .fla

AC3

.ac3, .mka

Photo

– up to 500 files/folders in a single layer

• The system can recognize the following files or

folders stored in the DLNA server:

– up to folders in the 19th layer

Photo Format

JPEG

Extension

.jpeg, .jpg, .jpe

– up to 999 files/folders in a single layer

• The system can support frame rate:

– up to 60 fps for AVCHD only.

PNG

.png

GIF

.gif

*6*10

– up to 30 fps for other video codecs.

• The system can support video bit rate up to

40 Mbps.

• The system can support video resolution up to

1920 × 1080p.

• Some USB devices may not work with this

system.

• The system can recognize Mass Storage Class

(MSC) devices (such as flash memory or an

HDD), Still Image Capture Devices (SICDs),

and 101-key keyboards.

MPO

.mpo

The system may not play this file format on a

DLNA server.

The system can only play standard definition

video on a DLNA server.

The system does not play DTS format files on

a DLNA server.

The system can only play Dolby Digital

format files on a DLNA server.

The system can support AVC up to Level 4.1.

The system does not play this file format on a

DLNA server.

The system can play AVCHD Ver.2.0 format

(AVCHD 3D/Progressive).

The system plays AVCHD format files that are

recorded on a digital video camera, etc.

The AVCHD format disc will not play if it has

not been correctly finalized.

The system does not play animated PNG or

animated GIF files.

• The system may not play high bit rate video files

from a DATA CD smoothly. It is recommended

to play high bit rate video files using a DATA

DVD or DATA BD.

*10

For MPO files other than 3D, the key image or

the first image is displayed.

62^US

Supported Audio

Formats

Audio formats supported by this system are

as follows.

Specifications

Amplifier Section

U.S.A. model only:

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL

HARMONIC DISTORTION:

(FTC)

Function

Format

“BD/DVD”

“TV”

Front L + Front R:

(DIGITAL IN)

With 3 ohms loads, both channels driven,

from 180 Hz – 20,000 Hz; rated 50 watts

per channel minimum RMS power, with

no more than 1% total harmonic

distortion from 250 milliwatts to rated

output.

LPCM 2ch

LPCM 5.1ch,

LPCM 7.1ch

–

Dolby Digital

Other models:

POWER OUTPUT (rated)

Front L/Front R:

Dolby TrueHD,

Dolby Digital

Plus

–

75 W + 75 W (at 3 ohms, 1 kHz,

1% THD)

POWER OUTPUT (reference)

Front L/Front R/Surround L/Surround R:

125 W (per channel at 3 ohms, 1 kHz)

Center:

DTS

DTS-ES

Discrete 6.1,

DTS-ES Matrix

6.1

DTS96/24

250 W (at 6 ohms, 1 kHz)

Subwoofer:

DTS-HD High

Resolution

Audio

–

250 W (at 6 ohms, 80 Hz)

Inputs (Analog)

AUDIO IN

Sensitivity: 1 V/400 mV

Inputs (Digital)

TV (Audio Return Channel/OPTICAL)

Supported formats: LPCM 2CH (up to

48 kHz), Dolby Digital, DTS

DTS-HD Master

Audio

–

a: Supported format.

–: Unsupported format.

* Decoded as DTS core.

Note

HDMI Section

Connector

For LPCM 2ch format, the supported sampling

frequency of the digital signal is up to 48 kHz

when using the “TV” function.

Type A (19pin)

BD/DVD/CD System

Signal format system

NTSC

USB Section

(USB) port:

Type A (For connecting USB memory,

memory card reader, digital still camera,

and digital video camera)

63^US

LAN Section

LAN (100) terminal

FM Tuner Section

System

100BASE-TX Terminal

PLL quartz-locked digital synthesizer

Tuning range

87.5 MHz – 108.0 MHz (100 kHz step)

Antenna (aerial)

Wireless LAN Section

Blu-ray Disc/DVD receiver

(HBD-E6100/HBD-E4100/

HBD-E3100/HBD-E2100)

Standards Compliance

IEEE 802.11 b/g/n

FM wire antenna (aerial)

Speakers

Front/Surround (SS-TSB123) for

BDV-E6100

Frequency and Channel

2.4 GHz band: channels 1–11

Front (SS-TSB123) for BDV-E4100

Dimensions (w/h/d) (approx.)

Bluetooth Section

Communication system

Bluetooth Specification version 3.0

Output

Bluetooth Specification Power Class 2

Maximum communication range

100 mm × 650 mm × 100 mm (4 in ×

25 / in × 4 in) (wall-mounted part)

260 mm × 1,200 mm × 260 mm

(10 / in × 47 / in × 10 / in) (whole

speaker)

Mass (approx.)

Line of sight approx. 10 m (33 ft)

Front: 1.3 kg (2 lb 14 oz) (wall-mounted

part with speaker cord)

2.9 kg (6 lb 7 oz) (whole speaker)

Surround: 1.4 kg (3 lb 2 oz)

(wall-mounted part with

speaker cord)

Frequency band

2.4 GHz band

Modulation method

FHSS (Freq Hopping Spread Spectrum)

Compatible Bluetooth profiles

A2DP 1.2 (Advanced Audio Distribution

Profile)

AVRCP 1.3 (Audio Video Remote

Control Profile)

3.0 kg (6 lb 10 oz) (whole

speaker)

Front/Surround (SS-TSB122) for

BDV-E3100

Supported Codecs

SBC , AAC

Surround (SS-TSB122) for

BDV-E4100

Dimensions (w/h/d) (approx.)

Transmission range (A2DP)

20 Hz – 20,000 Hz (Sampling frequency

44.1 kHz, 48 kHz)

90 mm × 205 mm × 91 mm (3 / in ×

8 / in × 3 / in)

The actual range will vary depending on factors

Mass (approx.)

such as obstacles between devices, magnetic

fields around a microwave oven, static

electricity, cordless phone, reception

sensitivity, antenna’s performance, operating

system, software application, etc.

Front: 0.53 kg (1 lb 3 oz) (with speaker

cord)

Surround: 0.62 kg (1 lb 6 oz) (with

speaker cord)

Bluetooth standard profiles indicate the purpose

of Bluetooth communication between devices.

Codec: Audio signal compression and

conversion format

Front/Surround (SS-TSB121) for

BDV-E2100

Dimensions (w/h/d) (approx.)

95 mm × 189 mm × 80 mm (3 / in ×

Subband Codec

7 / in × 3 / in)

Mass (approx.)

Front: 0.49 kg (1 lb 2 oz) (with speaker

cord)

Surround: 0.54 kg (1 lb 4 oz) (with

speaker cord)

64^US

Center (SS-CTB122) for BDV-E6100/

BDV-E4100/BDV-E3100

Dimensions (w/h/d) (approx.)

240 mm × 90 mm × 85 mm (9 / in ×

3 / in × 3 / in)

Mass (approx.)

0.58 kg (1 lb 5 oz) (with speaker cord)

Center (SS-CTB121) for BDV-E2100

Dimensions (w/h/d) (approx.)

225 mm × 84 mm × 75 mm (8 / in ×

3 / in × 3 in)

Mass (approx.)

0.5 kg (1 lb 2 oz) (with speaker cord)

Subwoofer (SS-WSB123) for

BDV-E6100/BDV-E4100/BDV-E3100

Dimensions (w/h/d) (approx.)

225 mm × 365 mm × 345 mm (8 / in ×

14 / in × 13 / in)

Mass (approx.)

5.8 kg (12 lb 13 oz) (with speaker cord)

Subwoofer (SS-WSB122) for

BDV-E2100

Dimensions (w/h/d) (approx.)

220 mm × 305 mm × 255 mm (8 / in ×

12 / in × 10 / in)

Mass (approx.)

3.8 kg (8 lb 7 oz) (with speaker cord)

General

Power requirements

120 V AC, 60 Hz

Power consumption

On: 95 W

Standby: 0.3 W (For details on the

setting, see page 43.)

Dimensions (w/h/d) (approx.)

430 mm × 50.5 mm × 296 mm (17 in ×

2 in × 11 / in) incl. projecting parts

Mass (approx.)

2.7 kg (5 lb 16 oz)

Design and specifications are subject to

change without notice.

• Standby power consumption: 0.3W

• Over 85% power efficiency of amplifier

block is achieved with the full digital

amplifier, S-Master.

65^US

Language Code List

The language spellings conform to the ISO 639: 1988 (E/F) standard.

Code Language

1027 Afar

1028 Abkhazian

1032 Afrikaans

1039 Amharic

1044 Arabic

1045 Assamese

1051 Aymara

1052 Azerbaijani

1053 Bashkir

1057 Byelorussian 1233 Armenian

1059 Bulgarian

1060 Bihari

1061 Bislama

1066 Bengali;

Bangla

1067 Tibetan

1070 Breton

1079 Catalan

1093 Corsican

1097 Czech

1103 Welsh

1105 Danish

1109 German

1130 Bhutani

1142 Greek

1144 English

1145 Esperanto

1149 Spanish

1150 Estonian

1151 Basque

1157 Persian

1165 Finnish

1166 Fiji

Code Language

1183 Irish

1186 Scots Gaelic 1349 Macedonian

1194 Galician

1196 Guarani

1203 Gujarati

1209 Hausa

1217 Hindi

Code Language

1347 Maori

Code Language

1507 Samoan

1508 Shona

1509 Somali

1511 Albanian

1512 Serbian

1513 Siswati

1514 Sesotho

1515 Sundanese

1516 Swedish

1517 Swahili

1521 Tamil

1350 Malayalam

1352 Mongolian

1353 Moldavian

1356 Marathi

1357 Malay

1358 Maltese

1363 Burmese

1365 Nauru

1369 Nepali

1376 Dutch

1379 Norwegian

1393 Occitan

1403 (Afan)Oromo 1529 Tigrinya

1226 Croatian

1229 Hungarian

1235 Interlingua

1239 Interlingue

1245 Inupiak

1248 Indonesian

1253 Icelandic

1254 Italian

1257 Hebrew

1261 Japanese

1269 Yiddish

1283 Javanese

1287 Georgian

1297 Kazakh

1298 Greenlandic

1299 Cambodian

1300 Kannada

1301 Korean

1305 Kashmiri

1307 Kurdish

1311 Kirghiz

1525 Telugu

1527 Tajik

1528 Thai

1408 Oriya

1531 Turkmen

1532 Tagalog

1534 Setswana

1535 Tonga

1538 Turkish

1539 Tsonga

1540 Tatar

1543 Twi

1557 Ukrainian

1564 Urdu

1417 Punjabi

1428 Polish

1435 Pashto;

Pushto

1436 Portuguese

1463 Quechua

1481 Rhaeto-

Romance

1482 Kirundi

1483 Romanian

1489 Russian

1572 Uzbek

1581 Vietnamese

1491 Kinyarwanda 1587 Volapük

1495 Sanskrit

1498 Sindhi

1501 Sangho

1502 Serbo-Croatian 1684 Chinese

1503 Singhalese

1505 Slovak

1613 Wolof

1632 Xhosa

1665 Yoruba

1313 Latin

1326 Lingala

1327 Laothian

1332 Lithuanian

1334 Latvian;

Lettish

1697 Zulu

1171 Faroese

1174 French

1181 Frisian

1506 Slovenian

1345 Malagasy

1703 Not specified

66^US

Parental Control/Area Code List

Code Area

2044 Argentina

2047 Australia

2046 Austria

2057 Belgium

2070 Brazil

2090 Chile

2092 China

2093 Colombia

2115 Denmark

2165 Finland

2174 France

2109 Germany

2200 Greece

2219 Hong Kong

2248 India

2238 Indonesia

2239 Ireland

2254 Italy

2276 Japan

2304 Korea

2333 Luxembourg

2363 Malaysia

2362 Mexico

2376 Netherlands

2390 New Zealand 2543 Taiwan

2499 Sweden

2086 Switzerland

2379 Norway

2427 Pakistan

2424 Philippines

2428 Poland

2436 Portugal

2489 Russia

2501 Singapore

2149 Spain

2528 Thailand

2184 United

Kingdom

67^US

Index

Numerics

3D 27

3D Output Setting 46

DVD Parental Control 50

DVD-ROM 24p Output 47

A/V SYNC 37

Attenuate - AUDIO 48

Audio DRC 48

Audio Language 49

Audio Output 48

Audio Return Channel 50

Audio Settings 48

Auto Display 50

Easy Network Settings 52

Easy Setup 23

FM Mode 38

BD Audio MIX Setting 48

BD Hybrid Disc Playback Layer 49

BD Internet Connection 49

BD Parental Control 50

BD/DVD Menu Language 49

BD/DVD Viewing Settings 49

BD-LIVE 26

Front panel 13

Front panel display 14

Gracenote Settings 50

BD-ROM 24p Output 47

Bluetooth 28

BONUSVIEW 26

HDMI

YCbCr/RGB (HDMI) 47

HDMI Deep Color Output 47

BRAVIA Sync 40

CD 60

Initialize Personal Information 52

Internet content 32

Child Lock 42

Cinema Conversion Mode 47

Connection Server Settings 51

Control for HDMI 40, 50

Internet Settings 51

Internet Video Parental Control 50

Internet Video Unrated 50

Language Code List 66

68^US

Main Unit illumination 50

Screen Format 46

Screen Saver 50

Multiplex broadcast sound 38

Screen Settings 46

SLEEP 42

Slideshow 36

Software License Information 51

Sound Effect 48

Speaker Settings 40, 49

Distance 41

Network Connection Diagnostics 51

Network Settings 51

Network Update 46

NFC 30

Level 41

Subtitle Language 49

System Information 51

OSD Language 50

Test Tone 41

Parental Control Area Code 49

Parental Control Settings 49

PARTY Auto Start 51

Password 49

TV Screen Size Setting for 3D 46

TV Type 46

Pause Mode 48

Play information 27

Playable discs 60

Update 46

USB 28

Quick Start Mode 50

WEP 22

WPA2-PSK (AES) 22

WPA2-PSK (TKIP) 22

WPA-PSK (AES) 22

WPA-PSK (TKIP) 22

Rear panel 14

Region code 61

Registered Remote Devices 51

Remote control 15

Remote Start 51

Renderer Access Control 51

Renderer Options 51

Reset to Factory Default Settings 52

Resetting 52

69^US

The software of this system may be updated in the future. To find out details on any

available updates, please visit the following URL.

http://www.sony.com/blurayhtsupport/

VocoPro Car Amplifier SE 690 Pro User Manual
Tektronix Car Satellite TV System TSG 100 User Manual
Tektronix Car Amplifier 5A48 User Manual
SoundMax SM CMD3004 User Manual
Sony Handycam NEXVG10 User Manual
Sony Handycam DCR DVD650 User Manual
Sony BDV E880 User Manual
Sanyo LNS S31 User Manual
Samsung SCH A212 User Manual
Rosewill RCX Z940 LX User Manual