Sherwood Blu ray Player BDP 904 User Manual

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 1

BDP-904

BLU-RAY DISC PLAYER

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 3

PRECAUTIONS

■Moisture condensation

Moisture may form on the lens in the following conditions.

• Immediately after a heater has been turned on.

• In a steamy or very humid room.

• When this unit is moved from a cold place to a warm one.

If moisture forms inside this unit, it may not operate properly.

In this case, turn on the power and wait about one hour for the moisture to evaporate.

■If there is noise interference on the TV while a broadcast is being received.

Depending on the reception condition of the TV, interference may appear on the TV screen while you are watching a TV

broadcast and this unit is left on. This is not a malfunction of this unit or the TV. To watch a TV broadcast, turn off this unit.

■Do not transport this unit with discs left in it.

■Do not place on the component such as amplifier or receiver that generates heat.

If so, the temperature inside this unit rises and malfunction may occur.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 4

cONTENTS

• Introduction

READ THIS BEFORE OPERATING YOUR UNIT ...................................................................................... 2

• System Connections

CONNECTING TO A/V AMPLIFIER OR RECEIVER .................................................................................. 5

CONNECTING TO TV WITH HDMI IN CONNECTOR ............................................................................... 7

CONNECTING TO NETWORK ................................................................................................................... 8

• Front Panel Controls .............................................................................................................................. 11

• Remote Controls .................................................................................................................................... 12

REMOTE CONTROL OPERATION RANGE ............................................................................................ 13

LOADING BATTERIES ............................................................................................................................. 13

• Preliminary Knowledge About Discs

PLAYABLE DISC TYPES .......................................................................................................................... 14

REGION CODE ......................................................................................................................................... 14

NOTES ON COPYRIGHT ......................................................................................................................... 15

SYMBOL ABOUT INVALID OPERATION ................................................................................................. 15

PLAYABLE FILES ..................................................................................................................................... 15

CARE AND HANDLING OF DISCS .......................................................................................................... 15

• Operations

PLAYING A DISC ...................................................................................................................................... 16

ENJOYING BONUSVIEW OR BD-LIVE .................................................................................................... 22

PLAYING FILES ........................................................................................................................................ 23

• System Settings ..................................................................................................................................... 28

SETTING THE SYSTEM ........................................................................................................................... 29

SETTING THE DISPLAY .......................................................................................................................... 30

SETTING THE AUDIO .............................................................................................................................. 31

SETTING THE LANGUAGE ...................................................................................................................... 32

SETTING THE PARENTAL CONTROL .................................................................................................... 33

SETTING THE NETWORK ....................................................................................................................... 34

• Definition Of Terms ................................................................................................................................ 36

• Troubleshooting Guide .......................................................................................................................... 38

• Specifications .......................................................................................................................................... 39

• License ..................................................................................................................................................... 40

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 5

System Connections

• Do not connect the AC input cord into the AC outlet when plugging and unplugging connection cords.

• Since different components often have different terminal names, carefully read the operating instructions of the component

connected.

• Be sure to observe the color coding when connecting audio and video cords.

• The supplied cords are a (stereo) audio cord and a composite video cord. Other cords are commercially-available cords.

This Unit

Do not stack this unit on the amplifier, etc. such as heating equipment.

This could damage this unit and/or the amplifier or could result in

malfunction.

■Caution :

Amplif

ier

cONNEcTING TO A/V AMPLIFIER OR REcEIVER

COAXIAL

Pr/Cr Cb/Pb Y

OPTICAL

DIGITAL INs

AUDIO IN

COMPONENT

VIDEO IN

(COMPOSITE)

VIDEO IN

HDMI, COMPONENT, COMPOSITE

(MONITOR)

VIDEO OUT

VIDEO IN

SPEAKERS

Speakers

A/V Amplifier or Receiver

FRONT L/R, CENTER, SURROUND L/R, SUBWOOFER, etc.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 6

■About video/HDMI OUT jacks

1. Connecting AUDIO OUTs

• Connect these jacks to the AUDIO IN jacks of BD(DVD,

CD, etc.) of your amplifier.

• You don’t need to make all kinds of video connections

between components. (e/ g., this unit to A/V amplifier, A/V

amplifier to TV and so on.)

Depending on what kinds of video jacks that A/V amplifier

TV, etc. has, we recommend you to make the same kinds

of video connections between components.

2. Connecting DIGITAL AUDIO OUTs

• Connect either the OPTICAL or the COAXIAL DIGITAL

OUT jack to the corresponding DIGITAL IN jack of your

amplifier. (You don’t need to do both.)

Jack type

Digital

Video resolution

■Notes :

High

quality

• When your amplifier is not compatible with the digital

signals that are output from this unit, loud noise or no

sound may be heard from the speakers, and it may be

harmful to your ears and damages the speakers. To

prevent it, you should disconnect the DIGITAL OUTs to

your amplifier and make analog audio connection.

• When making the COAXIAL DIGITAL connection, be sure

to use a 75Ω COAXIAL cord, not a conventional AUDIO

cord.

High Definition :

1080/24p, 1080p, 1080i, 720p

Standard Definition :

480p(/576p), 480i(/576i)

Analog

High Definition :

1080i, 720p

Standard Definition :

480p(/576p), 480i(/576i)

3. Connecting COMPOSITE VIDEO OUT

• Connect this jack to the (composite)VIDEO IN jack of your

amplifier or TV.

4. Connecting COMPONENT VIDEO OUTs

• Connect these jacks to the COMPONENT VIDEO OUT

jacks of your amplifier or TV.

• When making COMPONENT VIDEO connections,

connect “Y” to “Y”, “PB” to “PB” (, “Cb”, “B-Y”), “PR” to “PR”

(, “Cr”, “R-Y”).

Standard Definition :

480i(/576i)

Standard

quality

■Notes :

• If the resolutions of the video signals which are output

from the COMPONENT VIDEO OUTs and/or the HDMI

OUT and your TV are not matched, the picture is not

clear, natural or displayed.

■About audio/HDMI OUT jacks

• You don’t need to make all kinds of audio connections.

Connect this unit to A/V amplifier depending on the audio

input jack that A/V amplifier has.

To prevent it, you should set the Resolution to one which

the TV can handle. (For details, refer to “SETTING THE

DISPLAY” on page 30.)

Jack type

• Do not connect the unit to the TV through a VCR.

Otherwise the picture may be disturbed due to the copy

protection function.

High

quality

Digital

5. HDMI OUT CONNECTOR

• Refer to “CONNECTING TO TV WITH HDMI IN

CONNECTOR” on next page.

6. LAN CONNECTOR

• Refer to “CONNECTING TO NETWORK” on page 9.

7. AC INPUT CORD

• Plug the cord into a wall AC outlet.

Analog

Standard

quality

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 7

cONNEcTING TO TV WITH HDMI IN cONNEcTOR

• If you have a HDMI IN connector equipped TV or projector, etc., connected it to the HDMI OUT connector of this unit using a

commercially available HDMI cord.

The HDMI connection can carry uncompressed digital video and multi-channel (up to 7.1ch) digital audio signals.

• Among the HDMI IN connector equipped TV or projector, etc., some do not support audio output (for examples, projectors).

In such a case, make an audio connection between this unit and A/V amplifier.

• If you have a DVI IN connector equipped TV or projector, etc., compatible with both DVI and High-bandwidth Digital Content

Protection (HDCP), connect it to the HDMI OUT connector of this unit using a commercially available HDMI-DVI converter

cord.

Since the HDMI-to-DVI connection cannot carry audio signals, you should make an audio connection. (For details on audio

connection, refer to the operating instructions of the DVI IN connector equipped component.)

• If you have a HDMI or DVI connector equipped A/V amplifier, you can connect this unit to TV or projector, etc., through A/V

amplifier. (For details on connection between components, refer to the operating instructions of your amplifier.)

This unit

TV, Projector, etc.

(analog) AUDIO IN

DVI and audio connections

(analog) AUDIO OUT

DIGITAL OUT

DIGITAL IN

DVI

HDMI

■Copyright protection system

• This unit supports HDCP (High-bandwidth Digital Contents Protection), technology to protect copyright of digital video signals

against illegal duplication. HDCP must also be supported on the components connected to this unit.

If a component incompatible with HDCP is connected, the video signals will not be output properly.

• This unit is HDMI Ver. 1.3 compatible.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing

LLC.

■Notes :

• When connecting the HDMI OUT connector to TV or projector, etc., you should set Display and Audio settings correctly. (For

details, refer to “SETTING THE DISPLAY” on page 30 and “SETTING THE AUDIO” on page 31.)

• For stable signal transfer, we recommend using HDMI cords that are a maximum of 5 meters in length.

• Among the components that support HDMI, some components can control other components via the HDMI connector.

However, this unit cannot be controlled by another component via the HDMI connector.

• The audio signals from the HDMI connector (including the sampling frequency and bit length) may be limited by the

component that is connected.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 8

cONNEcTING TO NETWORK

• You can enjoy a variety of content with interactive functions by connecting to the internet when playing BD-LIVE compatible

discs.

• Connect the LAN connector of this unit to your internet source.

This unit

LAN

Internet

Modem

Broadband router

■Notes :

• After making a broadband internet connection, you should set the communication setting. (For details, refer to “SETTING THE

NETWORK” on page 34.)

• When using a broadband internet connection, a contract with an internet service provider is required. For more information,

contact your nearest internet service provider.

• Refer to the operating instructions of the equipment because the connected equipment and connection method may differ

depending on your internet environment.

• Use a LAN cable/router supporting 10 BASE-T/100 BASE-TX.

• Some LAN cables are easily affected by noise.

We recommend using a shielded type cable.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 9

■Video output resolution

• The video output resolution differs depending on the Resolution setting.

(For details, refer to “SETTING THE DISPLAY” on page 30.)

Video OUTs

Resolution setting

(Composite) VIDEO OUT

480i(NTSC)(or 576i(PAL))

COMPONENT OUTs

1, 2

HDMI OUT

highest resolution

1080p

HDMI Auto

1080p

1080i

1080i*

1, 2

1080i

1, 2

720p*

720p

480p

480p(NTSC)(or 576p(PAL))

480i(NTSC)(or 576i(PAL))

480p(NTSC)(or 576p(PAL))

480i(NTSC)(or 576i(PAL))

480i

: • When the COMPONENT OUTs and the HDMI OUT are connected to your TV, the video signals of 480i(NTSC)(or 576i(PAL)) will be output.

: • When the HDMI OUT is not connected to your TV and the copy protected DVD Videos are played, the video signals of 480p(or 576p) will be

output.

■Notes :

• If the resolution of video signal to be output from COMPONENT OUTs or HDMI OUT does not match that of your TV, the

picture is not clear, natural or displayed.

Should this happen, first make (composite) video connection between this unit and TV, and select the (composite) VIDEO as

an input source on the TV to display the setting menu, then set the Resolution correctly. (For details on the resolution

acceptable for your TV, refer to its operating instructions.)

• When the HDMI OUT connector is connected to your TV, the TV reports to this unit what resolutions it supports. Therefore, if

you set the Resolution to HDMI Auto, this unit outputs the video signals of the highest resolution acceptable for your TV.

In this case, you cannot select the resolution inacceptable for your TV.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 10

■Audio output signals

• The audio output differs as follows, depending on the audio format, output jack and Digital Output settings.

(For details, refer to “SETTING THE AUDIO” on page 31.)

Digital

Analog

Audio format Digital Output setting

HDMI OUT *

OPTICAL/COAXIAL OUTs

Dolby Digital 5.1CH

DTS 5.1CH

AUDIO OUTs

Bitstream HD

Bitstream Legacy

Bitstream Mixed

PCM 7.1

Dolby Digital 5.1CH

DTS 5.1CH

Dolby Digital

2CH

PCM 5.1CH

PCM 2CH

PCM 5.1

PCM 2CH

PCM Stereo

PCM 2CH

Dolby Digital Plus 7.1CH* /

Dolby TrueHD 7.1CH*

Bitstream HD

Dolby Digital 5.1CH*

Bitstream Legacy

Bitstream Mixed

PCM 7.1

Dolby Digital 5.1CH

DTS 5.1CH

Dolby Digital 5.1CH

DTS 5.1CH

Dolby Digital

Plus/ Dolby

TrueHD

2CH

PCM 2CH*

PCM 7.1CH

PCM 5.1

PCM 2CH*

PCM 5.1CH

PCM Stereo

PCM 2CH*

PCM 2CH

DTS-HD High Resolution

Bitstream HD

PCM 2CH

Audio 7.1CH* /DTS-HD Master

Audio 7.1CH*

DTS-HD High

Resolution

Bitstream Legacy

Bitstream Mixed

PCM 7.1

DTS 5.1CH

PCM 2CH

DTS 5.1CH

PCM 2CH

DTS 5.1CH

PCM 7.1CH

PCM 5.1CH

PCM 2CH

DTS 5.1CH

PCM 5.1CH

PCM 2CH

PCM 7.1CH

DTS 5.1CH

PCM 7.1CH

PCM 5.1CH

PCM 2CH

DTS 5.1CH

PCM 2CH

DTS 2CH

2CH

Audio/DTS-HD

Master Audio

PCM 5.1

PCM Stereo

Bitstream HD

Bitstream Legacy

Bitstream Mixed

PCM 7.1

DTS

2CH

PCM 5.1

PCM Stereo

Bitstream HD

Bitstream Legacy

Bitstream Mixed

PCM 7.1

PCM 2CH*

DTS 5.1CH

LPCM 7.1CH

(48/96 kHz)

PCM 2CH*

PCM 5.1

PCM 2CH*

PCM Stereo

Bitstream HD

Bitstream Legacy

Bitstream Mixed

PCM 7.1

PCM 2CH*

LPCM 5.1CH

(192 kHz)

PCM 2CH*

PCM 5.1

PCM 2CH*

PCM Stereo

Bitstream HD

Bitstream Legacy

Bitstream Mixed

PCM 7.1

PCM 2CH*

PCM 2CH

DTS 2CH

PCM 2CH

LPCM 2CH

(48/44.1 kHz)

PCM 2CH

PCM 5.1

PCM Stereo

: • When the A/V amplifier does not support HD Audio (Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution Audio and DTS-HD Master

Audio) but supports Dolby Digital/DTS, a Dolby Digital or DTS bitstream is output.

• When the A/V amplifier does not support HD Audio and Dolby Digital/DTS but supports multi-channel LPCM, up to PCM 7.1CH is output.

• When the A/V amplifier does not support LPCM at higher sampling frequency, LPCM at lower sampling frequency is output.

: When the A/V amplifier supports HD Audio, HD Audio is output.

: When the PCM Downsampling is set to 48 kHz, the audio signal is downsampled to 48 kHz.

: When the HDMI connection between components is made, PCM 2CH signal may be output.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 11

Front Panel Controls

1. POWER switch

9. RANDOM button

10. DISC TRAY

2. POWER ON/STANDBY button/indicator

3. OPEN/CLOSE( ) button

11. REMOTE SENSOR

12. FLUORESCENT DISPLAY

For details, see below.

13. USB connector

4. PLAY/PAUSE(▶

5. STOP(■) button

6. FORWARD/BACKWARD SKIP(▶▶

■

) button

■

■◀◀) buttons

7. INFORMATION button

For details, see below.

8. REPEAT button

■FLUORESCENT DISPLAY

Media indicators

HDMI indicator

REPEAT indicators

RANDOM indicator

Sound recording system indicators

Resolution indicators

Title/chapter/track number, playing time, operating information, etc.

■USB CONNECTOR

• This connector can be connected to a USB memory device for playback of MP3, WMA or

JPEG files stored on it. (For details, refer to “PLAYING FILES” on page 23.)

• To enjoy BONUSVIEW and BD-LIVE functions, you can connect a USB memory device

(minimum 1GB capacity (2GB or more recommended)) supporting FAT 32 and USB 2.0

High Speed (480 Mbit/s) to this connector, too. (For details, refer to “ENJOYING

BONUSVIEW OR BD-LIVE” on page 22.)

■Notes :

• Before connecting a USB memory device, open the cover.

• Do not use a USB extension cable when connecting a USB memory device to this

connector.

• After playback of files or Virtual Package/BD-LIVE data, remove the USB memory device in

the stop mode or the standby mode.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 12

Remote Controls

LED

POWER ON button

NUMERIC buttons

STANDBY button

CLEAR button

GO TO button

STEP(

) button

SLOW(

) button

STOP(■) button

PLAY/PAUSE(▶/

■

) button

FORWARD/BACKWARD

SEARCH(▶▶/◀◀) buttons

FORWARD/BACKWARD

SKIP(▶▶

■

■■

◀◀) buttons

COLOR buttons (RED(A), GREEN(B),

YELLOW(C), BLUE(D))

HOME MENU button

DISC MENU button

CURSOR UP/DOWN/LEFT/RIGHT,

OK buttons

POP UP MENU button

RETURN button

SUBTITLE button

AUDIO button

ANGLE button

DISPLAY button

REPEAT button

REPEAT A-B button

DIMMER button

PIP button

RANDOM button

OPEN/CLOSE ( ) button

■Note :

• You can use the COLOR buttons to select the items on some BD menus.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 13

REMOTE cONTROL OPERATION RANGE

• Use the remote control within a range of about 7 meters

(23 feet) and angles of up to 30 degrees aiming at the

remote sensor.

LOADING BATTERIES

1. Remove the cover.

2. Load two batteries (“AAA” size, 1.5V) matching

the polarity.

• Remove the batteries when they are not used for a long

time.

• Do not use the rechargeable batteries (Ni-Cd type).

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 14

Preliminary Knowledge About Discs

PLAYABLE DISc TYPES

REGION cODE

This unit supports the following discs.

• Blu-ray Disc player and BD-ROM or DVD Video discs are

assigned region codes according to the region in which

they are sold. If the region codes do not match, the disc

will not play.

Type

Logo

Playable format/mode

BDMV, AVCHD

BD-ROM

BD-RE/BD-R

Blu-ray Disc

Area

Region Code

DVD-Video

North America, Central America, South

America, Korea, Japan, Taiwan, Hong

Kong and South East Asia

DVD-Video, AVCHD

Europe, Greenland, French territories,

Middle East, Africa, Australia and New

Zealand

DVD-Video, AVCHD

Audio CD (CD-DA)

India, China, Russia, Central and South

Asia

A, B and C

All areas

Audio CD (CD-DA), MP3,

WMA, JPEG, AVI, WMV

DVD Region

Code

Area

Audio CD (CD-DA), MP3,

WMA, JPEG, AVI, WMV

North America

Europe, Japan, Middle East, Egypt,

South Africa, Greenland

• Only BD-RE/-R, DVD-R/-RW and CD-R/-RW discs

recorded with UDF or ISO9660 format can be played

back.

• This unit supports Ver 2.0 BD-ROM, Ver 3.0 BD-RE and

Ver 2.0 BD-R.

Taiwan, Korea, the Philippines,

Indonesia, Hong Kong

Mexico, South America, Central

America, Australia, New Zealand, Pacific

Islands, Caribbean

■Notes :

• Unfinalized BD-RE/-R, DVD-R/-RW and CD-R/-RW discs

can not be played back.

• Some 8 cm BD-REs/8 cm BD-Rs cannot be played on this

unit.

• When a BD-Java title is played, loading may take longer

than a normal title, or some functions may perform slowly.

• When an Audio CD recorded in DTS-ES or Dolby Digital

EX is played, noise may be heard.

Russia, Eastern Europe, India, most of

Africa, North Korea, Mongolia

China

ALL

All areas

Examples of playable discs :

U.S.A.

■Unplayable discs

• Since this unit cannot support disc types, formats and file

types not listed above, do not play such discs.

• Some BD-RE/BD-R, DVD-RWs/DVD-Rs or CD-Rs/CD-

RWs cannot be played due to incomplete disc finalization,

recording quality or physical condition of the disc,

characteristics of recording device or authoring software,

etc.

Europe

BDs

See the operating instructions supplied with your recording

device for more information.

DVDs

■Color system format

• Depending on the countries, this unit conforms to either

the NTSC color system for U.S.A, Canada, etc. or the PAL

for Europe, Australia, China, etc.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 15

■JPEG (“.jpg”, “.jpeg”)

NOTES ON cOPYRIGHT

• Maximum resolution : 4,272x2,848 pixels.

• JPEG format images stored in progressive format cannot

be played back.

• Audio-visual material may consist of copyrighted works

which must not be recorded without the authority of the

owner of the copyright. Refer to relevant laws in your

country.

• This product incorporates copyright protection

technology that is protected by U.S. patents and other

intellectual property rights. Use of this copyright

protection technology must be authorized by

Macrovision, and is intended for home and other limited

viewing uses only unless otherwise authorized by

Macrovision. Reverse engineering or disassembly is

prohibited.

■AVI (“.avi”)

• Playable codec : Xvid

• Maximum size of image : 1920 x 1080@30 fps

■WMV (“.wmv”)

• Playable codec : WMV9

• Maximum size of image : 1920 x 1080@30 fps

cARE AND HANDLING OF DIScS

• In handling a disc, hold it carefully

with edges.

SYMBOL ABOUT INVALID OPERATION

• When you press a button, if the unit does not accept its

operation,

appears on the TV screen.

Operations are occasionally unacceptable even if

not displayed.

• Do not stick paper or write

anything on the printed surface.

※Invalid operation may occur as expected if :

• The region codes of the unit is different from that of the

disc and playback will not be allowed.

• The parental control works.

(For details, refer to "SETTING THE PARENTAL

CONTROL" on page 33.)

• BD/DVD Video operations and functions may be

different from the explanations in this manual and some

operations may be prohibited due to disc

manufacturer’s settings.

• Fingermarks and dust on the

recorded surface should be

carefully wiped off with a soft cloth.

Wipe straight from the inside to the

outside of the disc.

• Always keep the discs in their

cases after use to protect them

from dust and scratches.

PLAYABLE FILES

• Characters except "A~Z", "a~z", "0~9", " - " may be not

displayed.

• This unit supports multi-session discs. Some multi-

session discs may take a long time to load and some

may not be loaded at all.

• Do not use a cracked, deformed, or repaired disc.

These discs are easily broken and may cause serious

personal injury and apparatus malfunction.

■Notes :

• For some files, it may not be possible to use certain

functions during playback.

• It may not be possible to play some files, even if they

have the extension of a file playable on this player.

• Files protected by DRM (Digital Rights Management)

cannot be played.

■Notes:

• Because the temperature inside this unit is very high, in

case of no further playback of disc, unload the disc to

prevent the high temperature from deforming the disc.

• Do not expose discs to direct sunlight, high humidity or

high temperature for a long time.

■MP3 (“.mp3”)

• Sampling frequency : 44.1 kHz, 48 kHz.

• Bit rate : Up to 320 kbps.

• Fixed bit-rate files are recommended. Variable bit-rate

(VBR) files are playable, but playing time may be

displayed incorrectly.

• When loading or unloading a disc in the disc tray, always

place it with the printed side up.

• ID3 Tag is not available.

• MP3i and MP3 Pro are not available.

■WMA (“.wma”)

• Sampling frequency : 44.1 kHz, 48 kHz.

• Bit rate : Up to 192 kbps.

• WMA Tag is not available.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 16

Operations

■Before starting playback

• First set this unit as desired for optimum performance, doing the system setting procedures. (For details, refer to "System

Settings" on page 28.)

• For explanation purposes, this instructions explains the OSD(On-Screen Display) language displayed on TV in English.

• Usable discs and files for each operation/function are referred to by the icons :

means AVI and WMV files.

PLAYING A DISc

Example :

1. Before operation, enter the standby mode.

JPEG file

Video file

System Settings

Loaded disc

• The POWER ON/STANDBY indicator lights up amber.

This means that the unit is connected to the AC mains

and a small amount of current is retained to support

operational readiness.

• To turn the power completely off, press the POWER

switch again.

Music file

• When the Optical Disc Autoplay is set to On (default

setting), playback will automatically start. (For details,

refer to “Optical Disc AutoPlay” on page 29.)

Should this happen, ignore the step 4.

2. In the standby mode, turn the power on.

4. Press the CURSOR UP/DOWN buttons to select

the disc, then press the OK button. (When the

Optical Disc AutoPlay is se to Off.)

• Each time the POWER ON/STANDBY button on the

front panel is pressed, the unit is turned on to enter the

operating mode (the POWER ON/STANDBY indicator

lights up blue) or off to enter the standby mode.

• On the remote control, press the POWER ON button to

enter the operating mode or press the STANDBY

button to enter the standby mode.

3. Open the disc tray to load a disc with the printed

side up.

• Then playback will start.

• For some discs, the menu may be displayed first.

• 8 cm (3 inch) discs can be loaded on the inside circle of

the tray, too.

• Depending on the disc types, it may take times to read

the loaded disc.

• Then the main menu will be displayed on the TV

screen.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 17

Slow playback

To start playback from the menu

• To select the preferred item, press the CURSOR buttons

and press the OK button or press the NUMERIC buttons.

• Each time the SLOW (

) button is pressed, you can

play back the disc slowly at 3 step speeds.

→ Slow x 1/2 → Slow x 1/4 → Slow x 1/8

• To return to normal playback, press the PLAY/PAUSE

(▶/

■

) button.

Frame advance playback

■In case of use of the NUMERIC buttons on the

remote control

• When selecting “3” :

• When selecting “10” :

• When selecting “21” :

• Playback of the selected item starts.

• Each time the STEP (

advanced by one frame.

• To return to normal playback, press the PLAY/PAUSE

) button is pressed, the disc is

• When the selected item contains the subitems, repeat

the above step until the preferred item is selected.

• Depending on the disc, the contents of the menu and

the way to operate differ.

(▶/

■

) button.

To skip ahead or back

To stop playback

• During playback,

To skip

back

To skip

ahead

• When the STOP (■) button is pressed during playback

of BD Video, DVD Video or AVCHD discs, the point at

which the disc was stopped is stored in the memory.

(RESUME function : “Stop” mode.)

• Each time the button is pressed, a chapter/track is

skipped.

• When the BACKWARD SKIP (

■

◀◀) button is pressed

• Press the PLAY/PAUSE (▶/

■

) button again, then

once midway through a chapter/track, playback returns to

the beginning of that chapter/track. When it is pressed

again, a chapter/track is skipped.

playback will resume from this point. When the STOP

(■) button is pressed again, the RESUME function will

be canceled and it enters “FullStop” mode.

■Note :

Rapid playback

• For some BD Video discs which support Java

applications, the RESUME function will not work.

• During playback, you can play back disc at various

speeds.

To pause playback

To reverse

To advance

• Each time the button is pressed, the disc is advanced or

reversed fast at 7 step speeds.

→ Fast x 2 → x 4 → x 8 → x 16 → x 32 → x 64 → x128

• Then the unit will be in the “Pause” mode.

• To return to normal playback mode, press this button

again.

• To return to normal playback, press the PLAY/PAUSE

(▶/

■

) button.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 18

Displaying disc information

2. At the desired search mode, enter the number to

be played, pressing the NUMERIC buttons.

• During playback,

■When entering title, chapter, track number

Examples :

For “3” :

For “11” :

• Then the disc information is displayed on the TV screen.

■When entering the elapsed time

You can play a disc from the desired by specifying the

elapsed time from the beginning of the current title/disc.

Example : During playback of CD

Repeat

Disc type Current track/total track number

playback mode

Examples :

Track : 1 / 11

For “3 min. 15 sec.” :

For “1 hour. 59 min. 35 sec.” :

0 : 00 : 23

0 : 06 : 46

Off

Play

CD-DA

Elapsed time of Proceeding bar

the current track

Random

playback mode

■When clearing the numbers entered

• Press the CURSOR LEFT/RIGHT buttons to select the

number to be cleared, then press the CLEAR button.

Total playing time

of the current track

Playback

mode

• To turn off the information, press this button.

• Depending on the disc types, the disc information differs.

Playing the desired section of disc

• Then the selected number will be cleared.

1. During playback, press the GO TO button.

3. Press the OK button.

• Then the search mode is displayed on the TV screen for

several seconds.

• Each time this button is pressed, the search mode is

changed depending on the disc types as follows :

• Then playback will start from the selected section.

■Notes:

• If the disc does not contain the number you entered,

search playback will not work.

• Depending on the disc, search playback will not work or

may work differently.

Goto Title :

/ 30 (current:1) : Title search

→

↓

Goto Chapter :

/ 16 (current: 2) : Chapter search

↓

Goto Time :

Goto Track :

/2:24:12(Current:0:15:50):Time search

↓

Off

/ 11 (current: 1) : Track search

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 19

Playing in random order

Playing repeatedly

• You can play the tracks in random order.

• During playback, press the RANDOM button.

• You can play a current title, chapter, disc or track

repeatedly.

• During playback of the desired chapter/track, press the

REPEAT button.

• Each time this button is pressed, the random mode

changes as follows :

• Each time this button is pressed, the repeat mode

changes depending on the disc types as follows :

Random Off : Random mode off (normal playback)

↕

Random On : Random playback

The tracks on the disc are played back in

random order.

→ Repeat Off : Repeat mode off (normal playback)

↓

Repeat Title : Title repeat

↓

Repeat Chapter : Chapter repeat

Operations using disc menu, top menu,

and Pop-up menu

Many of BD Video and DVD Video disc contains disc

menu, top menu or pop-up menu which guides you

through the available functions in the disc.

→ Repeat Off : Repeat mode off (normal playback)

↓

Repeat All : Entire disc repeat

↓

■Note :

Repeat Track : Track repeat

• Contents of menus and corresponding menu operations

may vary among discs. (For details, refer to the disc

manual.)

■Note :

• For some BD Video discs which support Java

applications, the repeat playback will not work.

■Using the disc menu.

1. During playback, press the disc menu.

Playing a specific section repeatedly

• You can play a specific section within a title or track

repeatedly.

1. During playback at the beginning of the section,

press the REPEAT A-B button.

• Then the disc menu is displayed on the TV screen if

present on the disc.

2. Press the CURSOR buttons to select the desired

item, then press the OK button.

• Then “Repeat A-” is displayed on the TV screen.

2. At the end of the section, press the REPEAT A-B

button again.

• Then “Repeat A-B” is displayed and the section between

points A and B is played back repeatedly.

• To return to normal playback, press the REPEAT A-B

button repeatedly until “Repeat Off” is displayed.

■Note :

• Then the selected item is played back.

• For some BD Video discs which support Java applications,

the REPEAT A-B function will not work.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 20

■Using the top menu.

Switching the audio soundtrack

1. During playback, press the POPUP MENU button.

For discs on which multiple audio streams are recorded,

audio streams can be switched during playback. Also use this

procedure to switch the secondary audio for BD video on

which secondary audio is recorded.

• It is possible to change the audio language to a different

language from the selected one at the System Settings.

(For details, refer to “SETTING THE LANGUAGE” on

page 32.)

• Then the top menu is displayed on the TV screen if

present on the disc.

1. During playback, press the AUDIO button.

2. Press the CURSOR buttons to select the desired

item, then press the OK button.

• Then the selected item is played back.

■Using the pop-up menu.

• Then the audio stream information is displayed for

several seconds.

• This is a special feature available for some BD video.

When you press the POPUP button, a menu pops out

on the TV screen while the contents are still played

back.

Example : BD Videos on which secondary audio is recorded.

Current audio stream/total number of recorded audio streams

1. During playback, press the POPUP MENU button.

Audio

01 / 04 ENG Dolby Digital

Off

• Then the pop-up menu is displayed if present on the disc.

PIP Audio

2. Press the CURSOR buttons to select the desired

Secondary audio : Only selectable for BD Videos on which

secondary audio is recorded.

(Primary) audio

item, then press the OK button.

• Then the selected item is played back.

2. Press the CURSOR RIGHT button.

3. Press the POPUP button to exit.

• The pop-up menu will automatically disappear for some

discs.

• Then the audio stream menu is displayed.

• To switch the secondary audio, press the CURSOR

UP/DOWN buttons to select the PIP Audio, then press

the CURSOR RIGHT button.

3. Press the CURSOR UP/DOWN buttons to select

the desired audio stream, then press the OK

button.

• Then the selected audio stream will be switched.

■Notes :

• When the secondary audio is not heard, be sure to set

the Digital Output to PCM Stereo, Bitstream Mixed, PCM

5.1 or PCM 7.1. (For details, refer to “SETTING THE

AUDIO” on page 31.)

• When the primary and the secondary audio streams are

all switched, they will be mixed and heard together. If

confused, set the PIP Audio to Off to switch off the

secondary audio stream.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 21

Switching the subtitles

Switching the camera angles

For discs on which multiple subtitles are recorded, the

subtitles can be switched during playback. Also use this

procedure to switch the secondary subtitle for BD Video on

which secondary subtitle is recorded.

• For discs on which multiple angles are recorded, the angles

can be switched during playback.

■Note:

• It is possible to change the subtitle language to a different

language from the selected one at the System Settings.

(For details, refer to “SETTING THE LANGUAGE” on

page 32.)

• You can switch the camera angle at only the scene that

have been shot simultaneously from multiple camera

angles.

1. During playback at the scene recorded from

multiple camera angles, press the ANGLE

button.

1. During playback, press the SUBTITLE button.

Angle

01 / 08

• Then the subtitle information is displayed for several

seconds.

Current angle/total number of recorded

angles

Example : BD Videos on which secondary subtitle is recorded.

Current subtitle/total number of recorded subtitles

• Then the angle information is displayed for several

seconds.

2. Press the CURSOR RIGHT button.

Subtitle

01 / 08 ENG

Off

PIP Subtitle

• Then the angle menu is displayed.

Secondary subtitle : Only selectable for BD Videos on which

secondary subtitle is recorded.

(Primary) subtitle

3. Press the CURSOR UP/DOWN buttons to select

the desired angle, then press the OK button.

2. Press the CURSOR RIGHT button.

• Then the scene recorded from the selected angle will be

displayed.

• Then the subtitle menu is displayed.

• To switch the secondary subtitle, press the CURSOR

UP/DOWN buttons to select the PIP Subtitle, then press

the CURSOR RIGHT button.

Adjusting the brightness of the fluorescent

display

3. Press the CURSOR UP/DOWN buttons to select

the desired subtitle, then press the OK button.

• Then the selected subtitle will be displayed.

• To switch off the subtitle, select the Off.

■Note:

• Each time this button is pressed, the brightness of the

fluorescent display changes as follows :

• When the primary and the secondary subtitles are all

switched, both will be displayed on the TV screen. If

confused, set either of subtitles to Off.

→

ON → dimmer → Off

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 22

ENJOYING BONUSVIEW OR BD-LIVE

This unit is compatible with additional functions of BD Video,

BONUSVIEW (BD-ROM Profile 2.0) and BD-LIVE. For BD

Video discs compatible with BONUSVIEW, the functions of

Picture in Picture and Virtual Package are available.

For BD-LIVE compatible discs, you can enjoy a variety of

functions via the internet in addition to the BONUSVIEW

functions.

2. Press the CURSOR RIGHT button to enter the

PIP mode menu.

Virtual Package/BD-LIVE data is saved in Local Storage

(USB memory device connected to this unit).

To enjoy these functions, connect a USB memory device

(minimum 1 GB capacity (2 GB or more recommended))

supporting FAT 32 and USB 2.0 High Speed (480 Mbit/s) to

the USB connector. (For details, refer to “USB

CONNECTOR” on page 11.)

3. Press the CURSOR UP/DOWN buttons to select

the secondary video, then press the OK button.

• If there is insufficient storage space, the data will not be

copied/downloaded. Delete unneeded contents or use a

new USB memory device.

• If a USB memory device containing other contents

(previously recorded) is used, the video and audio may not

play back properly.

• Then the secondary video will be displayed.

Example :

• If the USB memory device is disconnected from this unit

during playback of Virtual Package/BD-LIVE contents,

playback of the disc will stop.

Primary

video

• Some time may be required for the contents to load (read/

write).

Secondary

video

■Notes :

• It may not be possible to use the BD-LIVE functions if

there is insufficient space on the USB memory device. In

this case, refer to “Erase Blu-ray Storage?” on page 29 for

erasing the Virtual Package contents and the BD-LIVE

contents in the USB memory device.

• Operation of USB memory devices is not guaranteed.

• Do not use a USB extension cable when connecting a

USB memory device to the USB connector.

Virtual Package

For BD Video discs compatible with Virtual Package,

contents are copied from the discs or internet to local

storage. It is automatically copied to the local storage prior

to playback. You can enjoy a variety of additional functions

including secondary video, secondary audio, subtitles,

movie trailer, etc.

Playing secondary video(Picture in Picture)

BD Video that includes secondary video and audio

compatible with Picture in Picture can be played back will

secondary video and audio simultaneously as a small video

in the corner.

• To listen to secondary audio or to display secondary

subtitle, refer to “Switching the audio soundtrack” on page

20 or “Switching the subtitles” on page 21.

■Note :

• The playback methods vary depending on the disc. (For

details, refer to the disc manual.)

BD-LIVE

In this unit, a variety of contents with interactive functions

are available through BD-LIVE compatible BD discs by

connecting to the internet. You can enjoy the download of

bonus features such as latest movie trailers to the USB

memory device, communication compatible BD-J

interactive games, etc.

• You can call up the secondary video at only the scene

that contains the secondary video. (For details on PIP

function of your disc, refer to the disc manual.)

• The available functions differ depending on the disc.

1. During playback at the scene that contains the

■Notes :

secondary video, press the PIP button.

• Regarding playback method of BD-LIVE contents, etc.,

perform the operations in accordance with the instructions

in the BD disc manual.

• To enjoy BD-LIVE functions, perform the broadband

internet connection and communication settings. (For

details, refer to “CONNECTING TO NETWORK” on page

8 and “SETTING THE NETWORK” on page 34.)

• Regarding the setup to rectrict access to BD-LIVE

contents, refer to “BD-Live Internet Access” on page 29.)

PIP

Off

• Then the PIP setting menu is displayed for several

seconds on the TV screen.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 23

PLAYING FILES

• You can play music files such as MP3 and WMA, picture

files such as JPEG and video files such as AVI and WMV

recorded onto a CD-R/-RW or a USB memory device.

4. Select the desired file using the CURSOR

buttons, then press the OK button or the

CURSOR RIGHT button.

1. In the stop mode, load a disc or insert a USB

memory into the USB connector.

• Then the corresponding dialog box is displayed

depending on whether the Playlist is selected as a

media or not as follows.

• Then the music and picture file symbols, etc are

displayed on the main menu.

• When selecting the Playlist

• When selecting the

Optical Disc or the USB 1

Example : When a USB memory is inserted.

Remove from Playlist

Play (File)

Add To Playlist

Play (File)

Video file

System Settings

Music file

■Note:

• When the JPEG file is selected as a type of file to be

played, the “Play(File)” cannot be selected.

JPEG file

5. Press the CURSOR UP/DOWN buttons to select

the desired item in the dialog box, then press the

OK button.

2. CURSOR UP/DOWN buttons to select the type

of file to be played, then press the CURSOR

RIGHT button.

■When selecting the “Remove from Playlist”

• The selected file is cleared in the playlist.

• Repeat the above steps 4 and 5 until other files are

cleared.

Example : When the Music

file is selected

Music

■When selecting the “Add To Playlist”

• The selected file is added in the playlist.

• Repeat the above steps 4 and 5 until other files are

added.

2 item(s)

Main Menu

Play Files

Playlist

USB 1

■Note :

Browse Pictures

Now Playing

• When a disc is unloaded or the USB memory is

disconnected, the files are all cleared in the playlist.

■When selecting the “Play (File)”

Play menu

Media menu

• Only the selected file will be played (and the file

information will be displayed on the TV screen when

playing a music file).

• Then the play menu of the selected type of file is

displayed.

Example : When playing a music file

3. Press the CURSOR buttons to select the desired

media in the media menu, then press the

CURSOR RIGHT button.

File : 1 / 1 Animals - When I dream. mp3

Title :

Artist :

Album

0 : 00 : 28

0 : 04 : 36

• Then the folder and files recorded onto the selected

media are displayed.

Off

Play

■Notes:

■Note:

• Even if a CD-R/CD-RW or a USB memory device

contains a mix of music, picture and video files, you will

only be able to browse the selected type of files (music,

picture or video).

• To play JPEG files, select the “Play Files” in the play

menu.

• When there are no files to be played onto the selected

media or folder, “

Empty” will be displayed.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 24

Selecting an item in the play menu

To stop playback

• The items listed in the play menu may vary depending on

the operation status and the selected media, etc.

■Note:

• Then the playback will be stopped and the play mode,

etc. will be displayed.

• During playback of file, press the STOP (■) button (or the

HOME MENU button) to display the play menu, etc.

• In the stop mode, press the CURSOR UP/DOWN buttons

to select an item in the play menu, then press the OK

button.

To pause playback

■When selecting the “Main Menu”

• The main menu will be returned to.

■When selecting the “Play Files”

• Press the CURSOR UP/DOWN buttons to select the

desired play mode in the play menu, then press the OK

button. Then playback will start according to the selected

play mode.

• Then the unit will be in “Pause” mode.

• To return to normal playback mode, press this button

again.

■Notes:

• When playing JPEG files, each file is displayed for the

time interval you specified.

• The selectable play mode may vary depending on the

operation status and the selected media, etc.

Slow playback

■When selecting the “Browse Pictures” or the “Browse

Music”

• The JPEG file or the music file will be changed to as the

type of file to be played.

• Each time the SLOW ( ) button is pressed, you can

play back the video files slowly at 3 step speeds.

■When selecting the “Add all to playlist”

• All the files are added in the playlist.

→ Slow x 1/2 → Slow x 1/4 → Slow x 1/8

■When selecting the “Remove all from playlist”

• All the files are cleared in the playlist.

• To return to normal playback, press the PLAY/PAUSE

(

) button.

■When selecting the “Previous folder”

• Each time this item is selected, the previous folder or the

previous menu will be returned to.

To specify the time interval

■When selecting the “Now Playing”

• The playback status for music files is displayed.

• During playback,

• Each time the SLOW ( ) button is pressed, you can

specify the time interval to display the JPEG file as

follows :

→ 5 seconds → 10 → 15 → 30

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 25

Displaying file information

Frame advance playback

• During playback,

• Each time the STEP( ) button is pressed, the video

file is advanced by one frame.

• Then the file information is displayed on the TV screen.

• To return to normal playback, press the PLAY/PAUSE

Example : During playback of video file.

Current file/total file number

(▶/

■

) button.

File type

Title

Repeat playback mode

To skip ahead or back

File : 2 / 3

0 : 01 : 59

.. Love.Actually.DVDDiv...

1 : 04 : 56

• During playback,

Off

Play

Random

playback mode

Elapsed time of

the current file

Proceeding bar

To skip

back

Total playing time of

the current file

Playback

mode

To skip

ahead

• To turn off the information, press this button.

• Depending on the file types, the file information differs.

• During playback of music files, the file information is

still displayed without pressing this button.

• Each time the button is pressed, a file is skipped.

• When the BACKWARD SKIP (

■◀◀) button is pressed

once midway through a MP3/WMA/VIDEO file,

playback returns to the beginning of that file. When it is

pressed again, a file is skipped.

Playing the desired section of file

Rapid playback

1. During playback, press the GO TO button.

• During playback, you can play back files at various

speeds depending on the type of file as follows :

To reverse

To advance

• Then the search mode is displayed on the TV screen for

several seconds.

• Each time this button is pressed, the search mode is

changed as follows :

• Each time the button is pressed, the file is advanced or

reversed fast at 7 step speeds.

→ Fast x2 → x4 → x8 → x16 → x32 → x64 → x128

Goto File :

/ 81 (current: 1) : File search

↕

• To return to normal playback, press the PLAY/PAUSE

(▶/

■

) button.

Goto Time :

/0:02:29(Current:0:00:39):Time search

2. At the desired search mode, enter the number to

be played, pressing the NUMERIC buttons.

■When entering file number

Examples :

• Each time the FORWARD SEARCH (▶▶) button is

pressed, the time interval to display is shortened as

follows :

For “3” :

For “11” :

→ 5 seconds → 2 → 1 → No Delay

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 26

Continued

■When entering the elapsed time

You can play from the desired by specifying the elapsed

time from the beginning of the current file.

Examples :

Playing in random order

• You can play the files in random order.

• During playback, press the RANDOM button.

For “3 min, 15 sec.” :

For “1 hour. 59 min. 35 sec.” :

■When clearing the number entered

• Press the CURSOR LEFT/RIGHT buttons to select the

number to be cleared, then press the CLEAR button.

• Each time this button is pressed, the random mode

changes as follows :

Random Off : Random mode off (normal playback)

↕

Random On : Random playback

The files are played back in random order.

To change the effect on displaying pictures

3. Press the OK button.

• You can display the JPEG files at the slide show

options you select.

1. During playback, press the POPUP MENU button.

• Then the playback will start from the selected section.

Slide Show Effects

Slide Show Delay

None

■Notes :

5 sec(s)

• If the media does not contain the number you entered,

search playback will not work.

• Depending on the files, search playback will not work or

may work differently.

• Then the Slide Show menu is displayed for several

seconds.

Playing repeatedly

2. Press the CURSOR UP/DOWN buttons to select

the desired item, then press the CURSOR RIGHT

button.

• You can play a current file or all files repeatedly.

• During playback of the desired file, press the REPEAT

button.

• Then the selected item menu is displayed.

3. Press the CURSOR UP/DOWN buttons to select

the desired option, then press the OK button.

• Each time this button is pressed, the repeat mode

changes depending on the file types as follows :

■When selecting the Slide Show Effects

• You can select the desired of different display modes as

follows :

→ Repeat Off : Repeat mode off (normal playback)

↓

→ None ↔ Horizontal Scroll ↔ Fade ↔ Shutter ←

Repeat All : All file repeat

↓

Repeat File : File repeat

■When selecting the Slide Show Delay

• You can select the desired of different time intervals to

display the JPEG files as follows :

Repeat Off : Repeat mode off (normal playback)

→ 5 seconds ↔ 2 ↔1 ↔ No Delay ↔10 ↔ 15 ↔ 30 ←

↕

Repeat All : All file repeat

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 27

Playing both the music files and the JPEG

files simultaneously

1. During playback of music files, press the OK

button.

• Then the play menu, etc are displayed.

2. In the play menu, press the CURSOR UP/DOWN

buttons to select the “Browse Pictures”, then

press the OK button.

• Then you can browse the JPEG files to be played.

3. Select the some JPEG files to be played and play

them in the desired play mode.

• Then you can see the JPEG files while listening to the

music files.

• While playing both the music files and the JPEG files,

the playback controls are effective for the JPEG files

only.

■To control the music files

1. Press the STOP (■) button to stop the playback of

the JPEG files.

• Then the play menu, etc. will be displayed.

2. Press the CURSOR UP/DOWN buttons to select the

“Now Playing” in the play menu, then press the OK

button.

• Then the music file information is displayed and you

can control the music files.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 28

System Settings

• The OSD (On-Screen Display) menu enables various audio/visual settings and adjustments.

1. In the stop mode, press CURSOR UP/DOWN buttons to select “Settings” in the main menu, then press the

CURSOR RIGHT button.

System

Display

Network

Info

HDMI Status

HDMI Preferred Format

TV Type

Connected

720p

NTSC

Resolution

TV Aspect

Film Mode

HDMI Auto

16:9 Pillarbox

Off

Display

Color Depth

24 Bit

Audio

Language

Parental

• During playback of BD Video, DVD Video or CD disc, if the STOP (■) button or the HOME MENU button is pressed, then

the main menu will be displayed.

• During playback of music, JPEG or video files, if the HOME MENU button is pressed, then the previous menu will be

displayed, in this case, if the HOME MENU button is pressed again, then the main menu is displayed.

2. Press the CURSOR UP/DOWN buttons to select the desired setting category, then press the CURSOR

RIGHT button.

• You can select the desired of various setting categories as follows :

System : See “SETTING THE SYSTEM” on page 29.

Network : See “SETTING THE NETWORK” on page 34.

Info : You can check the system information on this unit.

Display : See “SETTING THE DISPLAY” on page 30.

Audio : See “SETTING THE AUDIO” on page 31.

Language : See “SETTING THE LANGUAGE” on page 32.

Parental : See “SETTING THE PARENTAL CONTROL” on page 33.

■Note :

• Because the setting operation for Parental and Network differs, follow their own procedures.

3. Press the CURSOR UP/DOWN buttons to select the desired setting item, then press the CURSOR RIGHT

button.

• Then the selected item’s option menu will be displayed.

4. Press the CURSOR UP/DOWN buttons to select the desired option, then press the OK button to confirm your

selection.

• Then the previous screen will be displayed.

• To go back to the previous screen, press the CURSOR LEFT button or the RETURN button.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 29

SETTING THE SYSTEM

• For how to select the setting items and options, refer to “System Settings” on page 28.

• Settings with* are the default.

Setting items

Optical Disc AutoPlay

Options

On* :

Set whether to automatically play a disc or not Starts play automatically.

when loading it or turning on the Power under Off :

the condition that it is loaded.

Turns off the autoplay.

Limit Access :

Allows only the BD disc with owner certification to access contents from a BD-

LIVE website.

Always Allow Access* :

Allows all BD-LIVE discs to access contents from BD-LIVE websites.

Prohibit Access :

Prohibit all BD-LIVE discs from accessing contents from BD-LIVE websites.

BD-Live Internet Access

Set the access restriction to BD-LIVE contents

■Notes :

• The available functions differ depending on the disc.

• Regarding playback method of BD-LIVE contents, etc., perform the

operations in accordance with the instructions in the BD-LIVE disc manual.

• To enjoy BD-LIVE functions, perform the broadband internet connection and

communication settings. (For details, refer to “CONNECTING TO

NETWORK” on page 8 and “SETTING THE NETWORK” on page 34.)

BD-Live Storage (USB)

BD-LIVE contents is stored into the USB

memory device.

USB1 (~ GB Free)

Displays the storable memory capacity.

Screen Saver Duration

Set the period of time to activate screen saver

function.

A TV screen may be burned out if a static

picture is displayed for a long time in the stop

mode, etc.. To prevent this, the unit

automatically activate the screen saver

function if a static picture is displayed over the

period of time you set.

Off :

Inactivates screen saver function.

5*/10/20/30 Minutes

Activates screen saver function if a static picture is displayed over the period

of time you set.

■Note :

• To inactivate screen saver function, press any button.

Erase Blu-ray Storage?

Erase the Virtual Package and BD-LIVE

contents stored into the USB memory storage.

1. Perform the steps 1~3 in “System Settings” procedure on page 28 to select

“Erase Blu-ray Storage?” or “Reset Settings” on the system menu.

2. Press the OK button.

Then the dialog window will be displayed.

3. Press the CURSOR LEFT/RIGHT buttons to select “OK”, then press the OK

button.

Reset Settings

Reset all settings to the factory default except

the Parental settings, etc.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 30

SETTING THE DISPLAY

• For how to select the setting items and options, refer to “System Settings” on page 28.

• Settings with* are the default.

Setting items

Options

NTSC :

Select this when the video signal format of your TV and the discs is NTSC

color system for U.S.A., Canada, etc..

PAL :

TV type

Select this when the video signal format is PAL color system for Europe,

Australia, China, etc..

Set the video signal format depending on that

of your TV and disc.

■Note :

• If the color system of this unit is different from that of your TV and the discs,

the screen may be somewhat hard too see or the picture quality may be

poor. Only in this case, set the video signal format to another.

HDMI Auto* :

HDMI video resolution will be selected automatically depending on the HDMI-

compatible TV.

1080p : Outputs 1080 lines of progressive video.

1080i : Outputs 1080 lines of interlaced video.

720p : Outputs 720 lines of progressive video.

Resolution

Set the resolution of the Component and

HDMI video signal

480p : Outputs 480 lines(NTSC)(or 576 lines(PAL)) of progressive video.

480i : Outputs 480 lines(NTSC)(or 576 lines(PAL)) of interlaced video.

• For details on Resolution settings, refer to “Video output resolution” on page 9.

16:9 Wide* :

Select this when a wide-screen TV is connected. Discs recorded in wide-

screen format is played back over the entire TV screen.

16:9 Pillarbox :

When playing back 4:3 images, the picture is displayed in the center of the

16:9 screen with a 4:3 aspect ratio.

TV Aspect

Set the picture size according to aspect ratio

of your TV

4:3 Letterbox :

Select this to play back the discs recorded in wide-screen format with 4:3 TV

in the letter box mode (with black strips at the top and bottom).

On :

Select this to output 1080/24p video signals from HDMI OUT when playing

film based materials (24 frame).

Off* :

Select this when playing a materials other than film based materials (24

frame).

Film Mode

Set whether to output 1080/24p video signals

from HDMI OUT when playing film-based

materials (24 frame) on BD discs.

■Notes :

• 1080/24p video signals cannot be output from video OUTs other than HDMI

OUT.

• 1080/24p video signals can be output when the following conditions are met.

- HDMI OUT is connected to TV compatible with 1080/24p video signals.

- Resolution is set to HDMI Auto or 1080p.

36 Bit :

Select this to output the HDMI video signal with the 36 Bit color depth to TV

which supports 36 Bit HDMI deep color.

30 Bit :

Select this to output the HDMI video signal with the 30 Bit color depth.

24 Bit* :

Select this to output the HDMI video signal without the color depth effect to TV

which does not support HDMI deep color.

Color Depth

Set whether to output the HDMI video signal

with the color depth effect or not.

■Notes :

• For details on HDMI deep color which TV supports, refer to the operating

instructions of TV.

• If color depth setting is different from that which TV supports, picture may

flicker or be displayed abnormally. Should this happen, first make

(composite) video connection between this unit and TV, and select the

(composite) VIDEO as an input source on the TV to display the setting

menu, then set the Color Depth correctly.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 31

SETTING THE AUDIO

• For how to select the setting items and options, refer to “System Settings” on page 28.

• Settings with* are the default.

Setting items

Options

96 kHz :

Outputs audio signals at 96 kHz sampling frequency.

48 kHz* :

Outputs audio signals at 48 kHz sampling frequency.

PCM Downsampling

Set the maximum sampling frequency for the

PCM signals output from the OPTICAL/

COAXIAL DIGITAL OUTs.

■Note :

• When the A/V amplifier does not support LPCM at higher sampling

frequency, no sound or a loud sound may result. Should this happen, set it

to lower sampling frequency.

Digital Output

PCM Stereo*/Bitstream HD/Bitstream Legacy/Bitstream Mixed/PCM 5.1 /

PCM 7.1.

Set the audio format for the digital audio

signals output from the HDMI OUT or the

OPTICAL/COAXIAL DIGITAL OUTs

depending on what audio format A/V amplifier

supports.

• For details on the digital audio signals output from the HDMI OUT or the

OPTICAL/COAXIAL DIGITAL OUTs depending on Digital Output settings,

refer to “Audio output signals” on page 10.

On :

Dynamic Range Control

Set whether to compress the dynamic range

Turns on the dynamic range compression to hear low sounds easier.

Off* :

between the loudest and softest sounds when Turns it off.

Dolby Digital, Dolby Digital Plus or Dolby

TrueHD audio is played back.

Auto :

When Dolby TrueHD audio is played back, the dynamic range is automatically

adjusted.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 32

SETTING THE LANGUAGE

• For how to select the setting items and options, refer to “System Settings” on page 28.

• Settings with* are the default.

Setting items

Options

OSD

Set the language for unit’s OSD (On-Screen

English*/French/Spanish/Italian/German/Russian

Display)

Auto*:

Selects the language given priority in the disc.

English/French/Spanish/Italian/German/Portuguese/ - - - - - - /Urdu/

Vietnamese/Yoruba

Set the language for disc menu or pop-up

menu.

Auto*:

Audio

Selects the language given priority in the disc.

English/French/Spanish/Italian/German/Portuguese/ - - - - - - /Urdu/

Vietnamese/Yoruba

Set the language for audio.

Off* :

Subtitle

Displays no subtitles.

Set the language for subtitle.

English/French/Spanish/Italian/German/Portuguese/ - - - - - - /Urdu/

Vietnamese/Yoruba

■Notes :

• Depending on the discs, it may not be possible to change to the selected language.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 33

SETTING THE PARENTAL cONTROL

The parental control allows you to set a limit, which prevents your children from viewing inappropriate materials. If the ratings

exceed the levels you set, playback will be stopped, or inappropriate scenes such as violent scenes can be cut or replaced with

other scenes depending on the disc type.

■Notes :

• When you set the Parental Level low, some discs may not be played at all, in this case, set the Parental Level higher or the

parental control to Off.

• All discs may not respond to the Parental Level setting. Make sure this function works with your disc.

■When selecting the Parental Level

1. Perform the steps 1 and 2 in “System Settings”

1 [Kid Safe]* : Suitable for children.

procedure on page 28 to select the Parental.

2 [G] : General audience.

3 [PG] : Parental guidance suggested.

4 [PG-13] : Unsuitable for children under 13.

• When the Parental Control is set to On, the parental

5 [PG-R] : Parental guidance recommended.

password entry screen appears as follows.

6 [R] : Restricted; under 17 requires accompanying parent or

adult guardian.

7 [NC-17] : No one under 17 admitted.

8 [Adult] : Discs of any grades (adult/general/children) can be

played back.

Please Input 4-Digit Parental Password :

Parental Password

• The lower the level value, the stricter the limitation.

Cancel

3. Press the CURSOR UP/DOWN buttons to select

the desired option, then press the OK button to

confirm your selection.

• In this case, press the NUMERIC buttons to enter the 4-

digit numbers, press the CURSOR buttons to select “OK”

and press the OK button.

• Then the Parental menu will be displayed.

• Then the previous screen will be displayed.

■Note :

• Do not forget the password. When you enter the

password for the first time or if you forgot your password,

enter “3308” as a factory setting.

When selecting the Parental Password

• Then the new parental password entry screen appears.

2. Press the CURSOR UP/DOWN buttons to select

the setting item, then press the CURSOR

RIGHT button.

3. Press the NUMERIC buttons to enter the new 4-

digit numbers, press the CURSOR buttons to

select “OK” and press the OK button.

• Then the selected item’s option menu will be displayed.

• Then the parental password entry screen for confirmation

appears.

When selecting the Parental Control or the

Parental Level

4. Perform the above step 3.

■When selecting the Parental Control

Off* : Parental Control is inactive; all discs are played back.

On : Parental Control restricts playing discs according to

parental level you set.

• Then the new password will be changed to and the

previous screen will be displayed.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 34

SETTING THE NETWORK

• To access BD-LIVE contents from websites, you should connect this unit to the internet and set the communication settings.

(For details, “CONNECTING TO NETWORK” on page 8.)

• When you set the communication setting manually, the following information of the connected router or modem is required.

Confirm the information prior to the setting : IP address, Subnet mask, Gateway, Primary DNS and Secondary DNS.

1. Perform the steps 1 and 2 in “System Settings”

3. Press the CURSOR RIGHT button to display the

procedure on page 28 to select the Network.

IP Mode.

• Then the network setting menu will be displayed.

Off:

Disables this unit’s LAN capabilities.

Manual :

Configures network settings manually.

Dynamic (default setting) :

Automatically configures the network settings by the DHCP

server function of the router or modem.

Wired :

Configures network settings depending on your internet

environment, etc. when connecting to the internet.

Network Test :

Detects the internet connection and automatically

configures the network settings by the DHCP server

function of the router or modem.

■Note :

• Select the Manual only when the DHCP server function of

the router or modem cannot be used for the automatic

configuration.

■Note :

• When IP Mode is set to Off, Network Test cannot be

selected.

4. Press the CURSOR UP/DOWN buttons to select

2. Press the CURSOR UP/DOWN buttons to select

the network configuration mode, then press the

OK button.

the desired IP Mode, then press the OK button.

■When selecting the Manual

• You can select IP Address, Subnet Mask, Gateway,

Primary DNS and Secondary DNS to configure them

manually.

• When selecting the Network Test, see page 35.

• On the IP Settings menu, “Link Status” and “Mac

Address” display the corresponding information merely.

When selecting the Wired

Then the IP Settings menu will be displayed as follows :

IP Settings

① Press the CURSOR UP/DOWN buttons to select the

desired option, then press the OK button.

Then the New Value entry screen will be displayed.

Link Status

Link Up

Example : When selecting IP Address

MAC Address

00:23:03:00:50:b4

Please enter a new IP Address.

Valid range of each segment is 0 to 255.

IP Mode

Dynamic

Current value

192.168.1.110

IP Address

192.168.1.110

255.255.255.0

192.168.1.1

168.126.63.1

0. 0. 0. 0

New Value

Subnet Mask

Gateway

Primary DNS

Secondary DNS

Cancel

② Enter the new value pressing the NUMERIC buttons,

then press the CURSOR buttons to select “OK” and

press the OK button.

Apply

Cancel

③ Repeat the above steps ① and ② until other new

values are all entered.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 35

Continued

When selecting the Network Test

5. Press the CURSOR UP/DOWN buttons to select

“Apply”, then press the OK button.

• Then the network test is automatically performed and the

result is displayed.

• Press the OK button to confirm the test result. Then the

network menu will be displayed.

■When selecting the Manual or the Dynamic

• Then the network test is automatically performed and the

result is displayed.

• Press the OK button to confirm the test result. Then the

network menu will be displayed.

■When selecting the Off

• The values for IP Address, Subnet Mask, Gateway,

Primary DNS and Secondary DNS are all cleared.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 36

Definition Of Terms

AVCHD (Advanced Video Codec High Definition)

The AVCHD is a high definition(HD) digital video camera

recorder format recording high-definition onto certain media

by using highly efficient codec technologies.

BonusView

Some BD-ROMs have bonus contents and other data that

can be downloaded to the external memory(local storage) for

enjoyment.

• “AVCHD” and the “AVCHD” logo are trademarks of

Panasonic Corporation and Sony Corporation.

• “BONUSVIEW” is trademark of Blu-ray Disc Association.

Dolby Digital

BDAV

A sound system developed by Dolby Laboratories Inc. that

gives movie theater ambience to audio output when the

product is connected to a Dolby Digital processor or amplifier.

BDAV (Blu-ray Disc Audio/Visual, BD-AV) refers to one of the

application formats used for writable Blu-ray discs such as

BD-R, BD-RE, etc. BDAV is a recording format equivalent to

DVD-VR (VR mode) of the DVD specifications.

Dolby Digital Plus

A sound system developed as an extension to Dolby Digital.

This audio coding technology supports 7.1 multi-channel

surround sound.

BD-J application

The BD-ROM format supports Java for interactive functions.

“BD-J” offers content providers almost unlimited functionality

when creating interactive BD-ROM titles.

Dolby TrueHD

• Java and all Java-based trademarks and logos are

trademarks or registered trademarks of Sun Microsystems,

Inc. in the U.S. and other countries.

Dolby TrueHD is a lossless coding technology that supports

up to 8 channels of multi-channel surround sound for the next

generation optical discs. The reproduced sound is true to the

original source bit-for-bit.

BD-LIVE

• Manufactured under license from Dolby Laboratories. Dolby

and the double-D symbol are trademarks of Dolby

Laboratories.

A variety of interactive content is available from BD-LIVE

compatible Blu-ray discs via the internet.

• “BD-LIVE” logo is trademark of Blu-ray Disc Association.

DTS

BDMV

This is a digital sound system developed by DTS, Inc. for use

in cinemas.

BDMV (Blu-ray Disc Movie, BD-MV) refers to one of the

application formats used for BD-ROM which is one of the Blu-

ray Disc specifications. BDMV is a recording format

equivalent to DVD-video of the DVD specification.

DTS-HD High Resolution Audio

DTS-HD High Resolution Audio is a new technology

developed for the next generation high definition optical disc

format.

BD-R

A BD-R (Blu-ray Disc Recordable) is a recordable, write-once

Blu-ray Disc. Since contents can be recorded and cannot be

overwritten, a BD-R can be used to archive data or for storing

and distributing video material.

DTS-HD Master Audio

DTS-HD Master Audio is a lossless audio compression

technology developed for the next generation high definition

optical disc format.

BD-RE

• Manufactured under license under U.S. Patent #'s:

5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616;

6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 &

other U.S. and worldwide patents issued & pending. DTS

and the Symbol are registered trademarks, & DTS-HD, DTS-

HD Master Audio, and the DTS logos are trademarks of

Reserved.

A BD-RE (Blu-ray Disc Rewritable) is a recordable and

rewritable Blu-ray Disc.

BD-ROM

BD-ROMs (Blu-ray Disc Read-Only Memory) are

commercially produced discs. Other than conventional movie

and video contents, these discs have enhanced features

such as interactive content, menu operations using pop-up

menus, selection of subtitle display, and slide shows.

Although a BD-ROM may contain any form of data, most BD-

ROM discs will contain movies in High Definition format for

playback on Blu-ray Disc players.

DVD Video

A disc format for storing MPEG-2 video on DVD, with

interactive menus, multiple soundtracks, subtitles, camera

angles, and so on.

•

is a trademark of DVD format/Logo licensing

Corporation.

Blu-ray Disc (BD)

A disc format developed for recording/playing high-definition

(HD) video (for HDTV, etc.), and for storing large amounts of

data. A single layer Blu-ray Disc holds up to 25 GB, and a

dual-layer Blu-ray Disc holds up to 50 GB of data.

• “Blu-ray Disc”, “Blu-ray” and “Blu-ray Disc” logo are

trademarks of Blu-ray Disc Association.

DVD-R

A DVD-R is a recordable, write-once DVD.

DVD-RW

A DVD-RW is a recordable and rewritable DVD. The DVD-R/

-RW has two different formats: VR format and Video format.

DVDs created in Video format have the same format as a

DVD video, while discs created in VR (Video Recording)

format allow the contents to be programmed or edited.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 37

HDMI

Progressive format

HDMI (High Definition Multimedia Interface) is a new

connection format that supports both video and audio on a

single digital connection.

Compared to the Interlace format that alternately shows

every other line of an image (field) to create one frame, the

Progressive format shows the entire image at once as a

single frame. This means that while the Interlace format can

show 30 frames/60 fields in one second, the Progressive

format can show 60 frames in one second. The overall

picture quality increases and still images, text, and horizontal

lines appear sharper.

The HDMI connection carries uncompressed, standard or

high definition digital video signals and multi-channel audio

signals to AV components such as HDMI equipped TVs, in

digital form without degradation.

• HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI

Licensing LLC.

Subtitle

These are the lines of text appearing at the bottom of the

screen which translate or transcribe the dialog. They are

recorded on many DVD and BD video discs.

Interlace format

Interlace format shows every other line of an image as a

single “field” and is the standard method for displaying

images on television. The even numbered field shows the

even numbered lines of an image, and the odd numbered

field shows the odd numbered lines of an image.

WMA (Windows Media™ Audio)

WMA is an audio data compression format developed by

Microsoft Corporation. WMA file size is smaller than that of

MP3.

JPEG (Joint Photographic Experts Group)

JPEG is a popular file format for still image compression and

storage.

WMV (Windows Media™ Video)

WMV is a video data compression format by Microsoft

Corporation.

• Windows Media and the Windows logo are trademarks or

registered trademarks of Microsoft Corporation in the United

States and/or other countries.

Linear PCM

Linear PCM is a signal recording format used for Audio CDs

and on some DVD and Blu-ray discs. The sound on Audio

CDs is recorded at 44.1 kHz with 16 bits. (Sound is recorded

between 48 kHz with 16 bits and 96 kHz with 24 bits on DVD

video discs and between 48 kHz with 16 bits and 192 kHz

with 24 bits on BD video discs.)

BD/DVD Video structure

BD/DVD Video discs typically one or more titles, which may

be subdivided into chapters.

Title 1

Title 2

MPEG-2

MPEG-2 (Moving Picture Experts Group phase 2) is one of

the video data compression schemes, which is adopted for

DVD videos and digital broadcasts worldwide. Some Blu-ray

Discs also use high bitrate MPEG-2.

Chapter 1 Chapter 2 Chapter 3

Chapter 1 Chapter 2

MP3

MP3 is an audio data compression format, which stands for

MPEG-1 Audio Layer 3. Using MP3, you can achieve a data

reduction of about 1:10.

• MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

Audio CD

Audio CDs contain tracks.

Track 1

Track 2

Track 3

Track 4

Multi Angle

This is a feature of DVD and BD video discs. In some discs,

the same scene is shot from different angles, and these are

stored in a single disc so you can enjoy playback from each

angle.

MP3/WMA/JPEG/AVI/WMV structure

On an MP3/WMA/JPEG/AVI/WMV disc, a folder can be a

member of another folder, creating hierarchical folder layers.

If you are familiar with a personal computer, you may easily

understand the hierarchical file/folder construction.

Multi Audio

Folder

File

This is a feature of DVD and BD video discs. This function

makes it possible to record different audio tracks for the

same video, so you can enhance your enjoyment by

switching the audio.

File

Folder

File File

Pop-up menu

An enhanced menu operation available on BD video discs.

The pop-up menu appears when POPUP MENU is pressed

during playback, and can be operated while playback is in

progress.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 38

Troubleshooting Guide

If a fault occurs, run through the table below before taking your unit for repair.

If the fault persists, attempt to solve it by switching the unit off and on again. If this fails to resolve the situation, consult your

dealer. Under no circumstances should you repair the unit yourself as this will invalidate the guarantee!

PROBLEM

POSSIBLE CAUSE

REMEDY

• Connect cord securely.

No power

• The AC input cord is disconnected.

• Check the outlet using a lamp or another appliance.

• Poor connection at AC wall outlet or the outlet is

inactive.

• Reload the disc with the printed side up.

• Use a playable disc.

No playback

• The disc is loaded upside down.

• The disc is not playable.

• Clean the disc.

• The disc is dirty.

• Load a disc that is correctly finalized.

• Set the parental level setting correctly.

(Refer to “SETTING THE PARENTAL CONTROL”

on page 33.)

• The recorded disc is not correctly finalized.

• The parental level is not set correctly.

• Adjust the setting correctly.

(Refer to “SYMBOL ABOUT INVALID OPERATION”

on page 15.)

• The symbol about invalid operation is displayed.

• The disc is scratched, dirty badly or unplayable.

• Press the POWER switch to switch the power off,

press the POWER switch again and then unload the

disc.

Malfunction

No picture

• Connect the cords correctly.

• Select the input source correctly.

• Use a playable disc.

• The video cords are disconnected.

• The incorrect selection of input source on the TV.

• The disc is not playable.

• Connect the unit so that the picture signal is

transferred directly to the TV.

Noisy or distorted picture • The unit is connected to a VCR directly and the

copyguard function is activated.

• Clean the disc.

• The disc is dirty.

• Sometimes small amount of picture distortion may

appear. This is not malfunction.

• It is in rapid advance or reverse playback, or in frame

advance playback.

• Set the resolution correctly. (Refer to “SETTING THE

DISPLAY” on page 30.)

Abnormal picture or no

picture

• The resolution is not set correctly for video signals to

be output form the COMPONENT and the HDMI

OUTs.

• This unit will not transfer the video signals via HDMI

connector to TV that does not support HDCP.

This is not malfunction.

• The TV does not support HDCP.

• Set the TV type correctly. (Refer to “SETTING THE

DISPLAY” on page 30.)

• The TV type of this unit is different from that of your

TV or the disc.

• Sometimes slight pause may occur.

This is not malfunction.

Slight pause of picture

No sound

• The layer transition occurs during playback of DVD

Videos, etc. recoded in dual-layer format.

• Connect the cords correctly.

• Connect the speakers correctly.

• Select the input source correctly.

• The audio cords are disconnected.

• The speakers are disconnected to the amplifier.

• The incorrect selection of input source on the

amplifier.

• Clean the disc.

Noisy or distorted sound

• The disc is dirty.

• Check the connections and connect all cords securely.

• Poor connections.

• Check the connections and connect all cords securely.

BD-LIVE contents

cannot be loaded

• Poor connections between this unit and broadband

router and/or modem.

• Connect the USB memory device to this unit.

• Set it to “Always Allow Access” (Refer to “SETTING

THE SYSTEM” on page 29.)

• The USB memory device is disconnected.

• The BD-Live Internet Access is set to “Prohibit

Access”.

• Load a disc that supports BD-LIVE.

• Set the network settings correctly. (Refer to “SETTING

THE NETWORK” on page 34.)

• The BD disc does not support BD-LIVE.

• The network settings are not set correctly.

• Replace the batteries.

• Remove the obstacle.

Remote control unit does • Batteries are not loaded or exhausted.

not operate. • The remote sensor is obstructed.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 39

Specifications

SYSTEM

• Type | Blu-ray Disc Player

• Laser | Semiconductor laser

• Video Signal System

| PAL / NTSC

AUDIO SECTION

• Frequency response

BD (Linear PCM), Sampling frequency : 48 kHz | 20 Hz~22 kHz

Sampling frequency : 96 kHz | 20 Hz~44 kHz

Sampling frequency : 192 kHz | 20 Hz~88 kHz

DVD (Linear PCM), Sampling frequency : 48 kHz | 20 Hz~22 kHz

Sampling frequency : 96 kHz | 20 Hz~44 kHz

CD, Sampling frequency : 44.1 kHz | 20 Hz~20 kHz

• Signal to noise ratio, IHF "A" weighted | 100 dB

• Dynamic range

BD / DVD / CD | 100 dB / 100 dB / 98 dB

• Total harmonic distortion, 1 kHz | 0.003 %

• Wow and flutter | Unmeasurable (less than 0.002 %)

• Analog output level, 10 kΩ | 2.0 V

• Digital output level

Coaxial, 75 Ω | 0.5 Vp-p

Optical, 660 nm | -21 ~ 15 dBm

VIDEO SECTION

• Output level, 75Ω

Video (regular, COMPOSITE) | 1.0 Vp-p

COMPONENT : Y / PB / PR | 1.0 / 0.7 / 0.7 Vp-p

HDMI output | 19 pin

GENERAL

• BD Storage / Service | USB 2.0 High Speed (480 Mbit/s)

• LAN | 10 BASE-T / 100 BASE-TX

• Power supply

| 230 V ~ 50 Hz

• Power consumption | 25 W

• Operating temperature | +41℉ ~ + 95℉ (+5℃ ~ +35℃)

• Dimensions(W x H x D, including protruding parts) | 430 x 72 x 290 mm (17 x 2-7/8 x 11-3/8 inches)

• Weight(Net) | 3.77 kg (8.3 lbs)

Note: Design and specifications are subject to change without notice for improvements.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 40

License

• This product uses some software programs which are distributed under the GPL license. Accordingly, the following GPL

software source codes that have been used in this product can be provided after asking at http://www.sherwoodamerica.com.

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General

Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for

all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program

whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General

Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure

that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source

code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know

you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the

rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights

that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so

they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission

to copy, distribute and/or modify the software.

Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this

free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is

not the original, so that any problems introduced by others will not reflect on the original authors' reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free

program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear

that any patent must be licensed for everyone's free use or not licensed at all.

The precise terms and conditions for copying, distribution and modification follow.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be

distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a

"work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work

containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language.

(Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you".

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of

running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on

the Program (independent of having been made by running the Program). Whether that is true depends on what the Program

does.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 41

1.You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that

you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep

intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the

Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in

exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and

copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these

conditions:

a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or

any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.

c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such

interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a

notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program

under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive

but does not normally print such an announcement, your work based on the Program is not required to print an

announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the

Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms,

do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part

of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose

permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to

exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the

Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under

the terms of Sections 1 and 2 above provided that you also do one of the following:

a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of

Sections 1 and 2 above on a medium customarily used for software interchange; or,

b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of

physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be

distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is

allowed only for noncommercial distribution and only if you received the program in object code or executable form with such

an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work,

complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus

the scripts used to control compilation and installation of the executable. However, as a special exception, the source code

distributed need not include anything that is normally distributed (in either source or binary form) with the major components

(compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies

the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent

access to copy the source code from the same place counts as distribution of the source code, even though third parties are

not compelled to copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any

attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights

under this License. However, parties who have received copies, or rights, from you under this License will not have their

licenses terminated so long as such parties remain in full compliance.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 42

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to

modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License.

Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of

this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license

from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not

impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing

compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent

issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this

License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously

your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the

Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who

receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to

refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is

intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of

any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is

implemented by public license practices. Many people have made generous contributions to the wide range of software

distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or

she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces,

the original copyright holder who places the Program under this License may add an explicit geographical distribution

limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such

case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time.

Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or

concerns.

Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies

to it and "any later version", you have the option of following the terms and conditions either of that version or of any later

version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may

choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to

the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free

Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving

the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO

THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE

KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND

PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME

THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT

HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED

ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 43

NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR

THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH

HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to

make it free software which everyone can redistribute and change under these terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most

effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the

full notice is found.

One line to give the program’s name and a brief idea of what it does.

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as

published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied

warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for

more details.

You should have received a copy of the GNU General Public License along with this program; if not, write to the Free

Software Foundation, Inc., 59

Temple Place, Suite 330, Boston, MA 02111-1307 USA

Also add information on how to contact you by electronic and paper mail.

If the program is interactive, make it output a short notice like this when it starts in an interactive mode:

Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for

details type ‘show w’. This is free software, and you are welcome to redistribute it under certain conditions; type ‘show c’ for

details.

The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course,

the commands you use may be called something other than ‘show w’ and ‘show c’; they could even be mouse-clicks or menu

items--whatever suits your program.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the

program, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers)

written by James Hacker.

signature of Ty Coon, 1 April 1989

Ty Coon, President of Vice

This General Public License does not permit incorporating you program into proprietary programs. If your program is subroutine

library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do,

use the GNU Library General Public License instead of this License.

BDP-904(A)_091204:BDP-904(A) 2009-12-07 오후 2:17 페이지 44

BDP-904

BLU-RAY DISC PLAYER

5707-00000-276-0S

Toshiba TEC MA 1450 User Manual
TANDBERG D13695.01 MPS 200 User Manual
Sunbeam Blender PB7650 User Manual
Sterling Plumbing SDRIOM 2 User Manual
Sony MEX BT2700 User Manual
Sony Handycam HDR XR550VE User Manual
Sony Handycam HDR CX130 User Manual
Samsung SMX F44RN User Manual
Samsung L750 User Manual
Samsung AD68 00839H User Manual