EQUINOX-HYPERCOM SETUP GUIDE
INCLUDED MODELS
XE-A207, XE-A23S, XE-A407, XE-A43S, XE-A507
Equinox-Hypercom Setup GUIDE
Determine the current ROM Version
PROCEDURE:
STEP 1
Press [MODE] key
STEP 2
Select 6 PROGRAM MODE
STEP 3
Select 1 READING
STEP 4
Select 16 ROM VERSION
See printed
PROGRAM Version
Upgrade NOT required if
you have the following
(or higher version):
XE-A207 / 23S = V1.09
XE-A407 / 43S = V1.07
XE-A507 = V1.04
Media
Systems
Group
3
Equinox-Hypercom Setup GUIDE
Connecting the Hypercom Device
PROCEDURE:
STEP 1
Connect the RJ-11 end of
the serial cable to the
Equinox/Hypercom Device
XE-A207
XE-A23S
XE-A407
XE-A43S
XE-A507
STEP 2
Connect the DB-9 end of
the cable to the COM port
on the back of the register
NOTE: On registers with two
(2) COM ports, the cable
should be connected to COM2
STEP 3
Plug in the
Equinox/Hypercom device
power supply
Power
COM
Media
Systems
Group
4
Equinox-Hypercom Setup GUIDE
Device Configuration – Register settings
PROCEDURE:
STEP 1
Press the [MODE] button
STEP 2
Select 6 PROGRAM MODE
and [CA/AT/NS]
STEP 3
Select 2 SETTING
and [CA/AT/NS]
STEP 4
Select 11 DEVICE CONFIG
Media
Systems
Group
5
Equinox-Hypercom Setup GUIDE
STEP 5
Select 4 EFT
STEP 5
Press the [.] button to
change the setting so
CHARGE = USED
STEP 6
Press the [CA/AT/NS]
button to save the change
STEP 7
Press the [ESC/CANCEL]
button 3 times
to return to cashier screen
Media
Systems
Group
6
Equinox-Hypercom Setup GUIDE
Confirm connection – EFT
PROCEDURE:
STEP 1
Press the [MODE] button
STEP 2
Select 6 PROGRAM MODE
and [CA/AT/NS]
STEP 3
Select 3 EFT TEST
and [CA/AT/NS]
STEP 4
Select 1 EFT COMM TEST
and [CA/AT/NS]
STEP 5
Receipt will print when
test is successful
NOTE: If error message
appears confirm all steps
Media
Systems
Group
7
Equinox-Hypercom Setup GUIDE
Credit Card operations – Basic Credit
PROCEDURE:
STEP 1
Enter sales normally on
cash register
STEP 2
For Payment press [CH]
button on keyboard
NOTE: If register has [CH] and
[CH2], always use [CH] button
for Credit Card payment
STEP 3
Register says
“PROCESSING…”
STEP 4
On the Equinox/Hypercom
terminal
Select
CREDIT
for the payment type
Media
Systems
Group
8
Equinox-Hypercom Setup GUIDE
STEP 5
Swipe the Credit Card on
the Equinox/Hypercom
terminal
STEP 6
Register will close out
transaction on approval of
the credit card.
After processing register
prints receipt based on
setting
Equinox/Hypercom
terminal will print
Customer signature
receipt
Media
Systems
Group
9
Equinox-Hypercom Setup GUIDE
Designs and specifications subject to change without notice.
Sharp is a registered trademark of Sharp Corporation. Equinox and Hypercom are trademarks of
Equinox Payments, LLC in the United States and/or other countries. All other trademarks and
registered trademarks are the property of their respective holders.
© 2012 Sharp Electronics Corporation. All rights reserved.
Media
Systems
Group
10
|