Sanyo LNS T03 User Manual

LCD PROJECTOR LENS  
MODEL NO. LNS-T03  
LENS REPLACEMENT  
AND INSTALLATION PROCEDURES  
NOTES ON REPLACEMENT AND INSTALLATION  
The procedures and the needed pars for lens installation depend on the type of  
cabinet. Before installing or replacing the lens, make sure the type of cabinet of your  
projector.  
When installing or replacing the lens, make sure the Lens Model No. matches with to  
your projector. Refer to the catalog, or contact your sales dealer for the proper Lens  
Model No.  
TYPE OF THE CABINET AND INSTALLATION PROCEDURES  
Check the type of cabinet of your projector and follow the respective installation procedure  
to install the lens correctly.  
Type of the Cabinet (1) (See Page 2) Type of the Cabinet (2) (See Page 5)  
For lens installation to the other models than above, contact your sales dealer.  
1AA6P1P4097-- (IDLS)  
{Type (1) Cabinet}  
LENS REPLACEMENT AND INSTALLATION PROCEDURE  
Remove 2 Screws A and Remove Lower Lens  
B
Cover. Push part B and pull the Lower Lens  
1
Cover down and remove it. (See Fig. 1.)  
A
LOWER LENS  
COVER  
Fig-1  
C
Remove 4 Screws C. Pull the Upper Lens Cover  
toward front and remove it. (See Fig. 2.)  
2
3
UPPER LENS  
COVER  
C
Fig-2  
UPPER LENS  
COVER  
Remove 2 Screws D and Cover Plate from the  
back of the Upper Lens Cover. (See Fig. 3.)  
COVER PLATE  
D
Fig-3  
-2-  
Remove Lens Protection Cap from the rear (mounting side) of the Projection Lens and attach the  
lens Attachment to the lens with 4 Screws. (Use screws attached to the lens.) See Fig. 4.  
4
LENS LOCK  
LEVER  
LENS ATTACHMENT  
Lens Attachment 01  
POA-LNA-01  
DRIVER INCLUDED  
IN THE LENS PACKAGE  
(610 303 8742)  
LENS MOUNTING  
BRACKET  
Part No. (610 275 6029)  
Fig-4  
Fig-5  
Grasp (release lock) the Lens Lock Lever and turn it fully upward. (See Fig. 6)  
Mount the Lens into the lens mounting bracket and grasp the lens lock lever and turn it counter-  
clockwise until the lever is locked. (See Fig. 5 and 7)  
After installing the lens, make sure the lens is not loose and properly installed.  
5
6
Set up the projector and project image on the screen. Turn the lens part "A" to adjust ZOOM. Turn  
the lens part "B" to adjust FOCUS.  
LENS LOCK  
LENS LOCK RELEASE  
Grasp (unlock) Lens  
Lock Lever and fully  
pulled downward until it  
is locked (clicked).  
Grasp (unlock)  
Lens Lock Lever  
and pulling  
upward.  
Turn the lens part "A"  
to adjust ZOOM.  
A
B
Turn the lens part "B"  
to adjust FOCUS.  
Fig-6  
Fig-7  
LENS INSTALLATION NEEDS TWO OR MORE PEOPLE.  
TO INSTALL THE LENS BY A SINGLE PERSON MAY RESULT IN A SERIOUS DAMAGE  
ON THE LENS OR THE PROJECTOR BY DROPPING OR BUMPING THE PRODUCTS.  
-3-  
Put back the Upper Lens Cover to the projector and Fix the Upper Lens Cover with 4 Screws C.  
(See Fig. 2.) Put back the Lower Lens Cover to the projector. Fix the Lower Cover with 2 Screws A.  
(See Fig. 1.)  
7
UPPER LENS  
COVER  
LOWER LENS  
COVER  
Fig-8  
-4-  
{Type (2) Cabinet}  
LENS REPLACEMENT AND INSTALLATION PROCEDURE  
A
Remove 2 Screws A and Remove Upper Lens  
Cover. Push part B and pull the Upper Lens  
1
Cover up and remove it. (See Fig. 1.)  
UPPER LENS  
COVER  
B
Fig-1  
C
Remove 4 Screws C. Pull the Lower Lens Cover  
2
3
toward front and remove it. (See Fig. 2.)  
LOWER LENS  
COVER  
C
Fig-2  
D
Remove 2 Screws D and Cover Plate from the  
back of the Upper Lens Cover. (See Fig. 3.)  
UPPER LENS  
COVER  
COVER PLATE  
Fig-3  
-5-  
Remove Lens Protection Cap from the rear (mounting side) of the Projection Lens and attach the  
lens Attachment to the lens with 4 Screws. (Use screws attached to the lens.) See Fig. 4.  
4
LENS LOCK  
LEVER  
LENS ATTACHMENT  
Lens Attachment 01  
POA-LNA-01  
DRIVER INCLUDED  
IN THE LENS PACKAGE  
(610 303 8742)  
LENS MOUNTING  
BRACKET  
Part No. (610 275 6029)  
Fig-4  
Fig-5  
Grasp (release lock) the Lens Lock Lever and turn it fully upward. (See Fig. 6)  
Mount the Lens into the lens mounting bracket and grasp the lens lock lever and turn it counter-  
clockwise until the lever is locked. (See Fig. 5 and 7)  
After installing the lens, make sure the lens is not loose and properly installed.  
5
6
Set up the projector and project image on the screen. Turn the lens part "A" to adjust ZOOM. Turn  
the lens part "B" to adjust FOCUS.  
LENS LOCK RELEASE  
LENS LOCK  
Grasp (unlock) Lens  
Lock Lever and fully  
pulled downward until  
it is locked (clicked).  
Grasp (unlock)  
Turn the lens part "A"  
to adjust ZOOM.  
Lens Lock Lever  
and pulling  
upward.  
A
B
Turn the lens part "B"  
to adjust FOCUS.  
Fig-6  
Fig-7  
LENS INSTALLATION NEEDS TWO OR MORE PEOPLE.  
TO INSTALL THE LENS BY A SINGLE PERSON MAY RESULT IN A SERIOUS DAMAGE  
ON THE LENS OR THE PROJECTOR BY DROPPING OR BUMPING THE PRODUCTS.  
-6-  
Put back the Lower Lens Cover to the projector and Fix the Lower Lens Cover with 4 Screws C.  
(See Fig. 2.) Put back the Upper Lens Cover to the projector. Fix the Upper Cover with 2 Screws A.  
(See Fig. 1.)  
7
UPPER LENS  
COVER  
LOWER LENS  
COVER  
Fig-8  
-7-  

Winegard Car Video System C 1000 User Manual
Waring MX1000R User Manual
ViewSonic VS10872 User Manual
Texas Instruments TLV320AIC12KEVMB K User Manual
Sony HC94E User Manual
Sony Ericsson VH410 User Manual
Sony Ericsson Car Stereo System HCA 20 User Manual
Sony DVD HANDYCAM User Manual
Sony DCR PC9 User Manual
Sony CMT NEZ5 User Manual