Before attempting to operate this product,
please read the instructions carefully.
SPD-3750T/3750/3700T/3700/3350/3310/2510
Speed Dome Camera Accessories
Installation Manual
STH-380PO/STH-370PO/STH-360PO
STH-370PI/STH-370PE
STB-370PC/STH-270PWV/STB-496PPV
STB-25PF/STB-30PF/STB-350PPM
STB-330PPM/STB-340PCM/STB-270B
Cautions and Warnings for Use
Table of Contents
1. Product Category …………………………………………………………………
1.1. HousingAccessories …………………………………………………………
1.2. Interface MountingAccessories ………………………………………………
1.3. Mounting BracketAccessories ………………………………………………
2. Speed Dome Camera Installation Category ………………………………………
3. PendantType Installation …………………………………………………………
3.1Wall MountType Installation …………………………………………………
4
4
5
5
7
8
Samsung Techwin cares for the environment at all product manufacturing stages
to preserve the environment, and is taking a number of steps to provide
customers with more environment-friendly products. The Eco mark represents
Samsung Techwin's will to create environment-friendly products, and indicates
that the product satisfies the EU RoHS Directive.
8
* CameraWiring Diagram …………………………………………………
3.2 Ceiling MountType Installation ……………………………………………
3.3 Indoor Flange MountType Installation ……………………………………
12
15
17
Thank you for purchasing our products.
This product is to be used for the installation of the Samsung Speed Dome
Camera series: SPD-3750T, 3700T, 3750, 3700, 3350, 3310, and 2510.
4. On-Ceiling MountType Installation ……………………………………………
5. Indoor Flush MountType Installation …………………………………………
6. MountingAccessory Installation ………………………………………………
Product External Dimensions ……………………………………………………
Product Specification ……………………………………………………………
21
25
30
34
36
Before installation, please read the user’s manual carefully.
- Note that you need to carefully read all contents related to safety and application
methods before installation.
- When using the product, the cautions/warnings, usage directions, operating methods,
and instructions must all be observed.
- The power and cable connections should be made by a product installation specialist.
Contents By Product Model
- Do not connect and use these accessories to products other than the Samsung Speed
Dome Camera Series.
STH-380PO …………………………………………………………………………
STH-370PO …………………………………………………………………………
STH-370PI …………………………………………………………………………
STH-370PE ………………………………………………………………………
STH-360PO …………………………………………………………………………
STH-270PWV ………………………………………………………………………
STB-496PPV ………………………………………………………………………
STB-370PC ………………………………………………………………………
STB-350PPM ……………………………………………………………………
STB-340PCM ……………………………………………………………………
STB-330PPM ……………………………………………………………………
STB-30PF …………………………………………………………………………
STB-270B …………………………………………………………………………
STB-25PF …………………………………………………………………………
8
8
8
25
8
8
15
17
30
30
30
15
30
17
- The locations for installing the accessory housing should be strong enough to fully
secure the accessories. All installations need to be carried out by experienced engineers.
- Do not use it for purposes other than the installation mentioned above.
- For product inquiries, please contact the retail shop where you bought the camera. The
use of equipment such as an aerial ladder while providing after-sales service shall be at
your expense.
3
2
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Product Category
Product Category
■ 1.2. Interface Mounting Accessories
■ 1. Product Category
■ 1.1. Housing Accessories
STB-370PC
:“On-Ceiling Install Base Mount” for the Samsung
Speed Dome Camera.
STH-380PO/STH-370PO/STH-360PO
: "Outdoor housing” with a built-in install base for the
Samsung Speed Dome Camera.
STH-380PO :
■ 1.3. Mounting Bracket Accessories
Ultra Low-Temperature Heavyweight(-40℃~50℃)
STH-370PO :
Low-Temperature Heavyweight(-20℃~50℃)
STH-270PWV
STH-360PO :
Low-Temperature Lightweight(-20℃~50℃)
:This “Wall Type Mount” is used for the installation of
STH-380PO,STH-370PO,STH-360PO,STH-370PI and
STB-25PF of the Samsung Speed Dome Camera.
STH-370PI
: "Indoor Housing” with a built-in install base for the
Samsung Speed Dome Camera.
STB-496PPV
:This “Ceiling Type Mount” is used for the installation
of STH-380PO,STH-370PO,STH-360PO,STH-370PI and
STB-25PF of the Samsung Speed Dome Camera.
STH-370PE
:“Indoor Flush Mount" with a built-in install base for the
Samsung Speed Dome Camera.
STB-25PF
:This “Indoor Flange” for the Samsung Speed Dome
Camera is useful to install the camera without a
housing.
5
4
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Product Category
Speed Dome Camera Installation Category
■ 2. Speed Dome Camera Installation Category
STB-30PF
Pendant Type
:“Ceiling Type Flange” for the Samsung Speed Dome
Camera.
STB-350PPM
: Parapet Mount” for the installation of indoor or
outdoor housing of Samsung Speed Dome Camera
STB-330PPM
Wall Type Mount
Ceiling Type Mount
Indoor Flange Type Mount
:“Pole Mount” for the Samsung Speed Dome Camera.
On-Ceiling Mount Type
STB-340PCM
:“Corner Mount” for the Samsung Speed Dome
Camera.
Indoor Flush Mount Type
STB-270B
: "Setup Box" for the Samsung Speed Dome Camera.
7
6
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Pendant Type Installation
Pendant Type Installation
1. Securing Wall Bracket and Wiring
■ 3. Pendant Type Installation
As shown in the picture, secure the wall bracket to the wall, and then pull the wires out
of the bracket. Please note that the STH-380PO housing requires an additional
installation of the fan heater adapter enclosed with the product.
■ 3.1 Wall Mount Type Installation
Fan Heater Adaptor
(STH-380PO Only)
Camera Adaptor
✽
To store the adaptor, the STB-270B Setup Box (Page 31) can be used.
Notes
ꢀ•ꢀꢀDoꢀnotꢀconnectꢀtheꢀcameraꢀtoꢀaꢀpowerꢀoutletꢀuntilꢀtheꢀinstallationꢀisꢀcomplete.ꢀSupplyingꢀ
power in the middle of the installation may cause fire or damage the product.
ꢀ•ꢀꢀSTH-370POꢀrequiresꢀanꢀadditionalꢀinstallationꢀofꢀtheꢀfanꢀheaterꢀadapterꢀenclosedꢀwithꢀtheꢀ
product. Connecting the fan heater to a power outlet used for the camera can cause fire or
accidents.
Knob
2. Preparing Housing
Open the hinged door at the bottom of the housing.
Hold the knob on the hinged door to open.
STH-380PO
STH-370PO
STH-360PO
STH-370PI
3. Connecting Housing and Bracket
To prevent the housing from falling down during the installation process, hook the safety
cable on the bracket loop as shown in the picture.
STH-270PWV
9
8
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Pendant Type Installation
Pendant Type Installation
5. Securing Housing
Check if the housing is properly attached
to the bracket, secure the housing to the
bracket with the enclosed screws.
Fan Heater Adaptor
(STH-380PO Only)
Fan Heater Connector
(Model: STH-370PO)
Camera Adaptor
6.Wiring Terminal Cables
Connect the cables to the terminal block
on the hinged door. Once the wiring is
successful, close the hinged door.
Notes
ꢀ•ꢀꢀTheꢀSTH-380ꢀhousing’sꢀfanꢀheaterꢀconnectorꢀmustꢀbeꢀconnectedꢀtoꢀitsꢀdedicatedꢀadapterꢀ
enclosed with the product.
ꢀ•ꢀꢀMakeꢀsureꢀtoꢀhookꢀtheꢀsafetyꢀcableꢀonꢀtheꢀbracketꢀloopꢀbeforeꢀconnectingꢀtheꢀhousing.
ꢀ•ꢀꢀNeglectingꢀthisꢀcautionꢀmayꢀexposeꢀyouꢀtoꢀinjuryꢀcausedꢀbyꢀaꢀfallenꢀhousing.
4. Assembling Housing and Bracket
✽
For the location of the wiring pins, please refer to the
“Camera Wiring Diagram” on the next page.
After hooking the safety cable, fit the housing into the fixture grooves on the bracket as
shown in the picture.When attaching, locate the "Samsung" logo on the housing facing
the center front.
Logo
11
10
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Pendant Type Installation
Pendant Type Installation
✽ Camera Wiring Diagram
7. Preparing Camera
This wiring diagram indicates the connection between the interface board and external
equipment. For wiring Samsung Techwin’s Speed Dome Camera and the accessories,
please refer to the Speed Dome Camera user’s manual.
Once the camera wiring is successful, prepare the
camera. Every housing-typed camera except the
flush model is provided with a dome cover first
detach the dome cover from the camera.
Video Output
Alarm
8. Setting Up Camera DIP Switches
DIP switches for communication and ID protocols are located on the bottom of the
camera. For the switch settings, refer to the appendix of this manual.
Alarm Output
ID(SW1)
Protocol(SW2)
Fan Heater
Connector
Alarm Input
9. Connecting Camera Safety Cable and Attaching Camera
Carefully attach the camera to the mount following the alignment guide marks as shown in
the picture. First hook the camera's safety cable on the mount, and then attach the camera.
The safety cable is coiled inside the install base.As shown in the leftward picture, pull out
the safety cable from the install base and then hook it to the mount.
Communications
and AUX
Power Supply
AC24V 2.5A
Alignment
Direction
Guides
Power Input
Ground
Safety
Cable
Refer to the below Control
Signal Connection diagram
Alignment
Direction
Guides
AUX Output
Alignment
Directions
Control Signal Connection
· RS485 Communications
Controller
or DVR
Camera
Notes
D+
D-
TXD+
TXD-
ꢀ•ꢀꢀTheꢀmaximumꢀcapacityꢀofꢀtheꢀalarmꢀandꢀ
AUXꢀoutputꢀterminalsꢀisꢀDC30Vꢀ2A.
ꢀ•ꢀꢀConnectingꢀtheꢀpowerꢀconnectorꢀandꢀGNDꢀ
incorrectlyꢀtoꢀtheꢀNC/NOꢀandꢀCOMꢀportsꢀ
can cause a short circuit which may lead
to fire and damage the camera.
✽
To attach the camera to the mount, refer to the alignment guide marks as shown in the picture.
· RS422 Communications
Controller
or DVR
TXD+
TXD-
Camera
Notes
D+
D-
ꢀ•ꢀꢀMakeꢀsureꢀtoꢀfirstꢀhookꢀtheꢀcamera'sꢀsafetyꢀcableꢀtoꢀtheꢀmountꢀbeforeꢀproceeding.ꢀOtherwiseꢀ
youꢀmayꢀbeꢀexposedꢀtoꢀseriousꢀinjuryꢀcausedꢀbyꢀaꢀfallenꢀcamera.
TX+
TX-
RXD+
RXD-
13
12
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Pendant Type Installation
Pendant Type Installation
■ 3.2 Ceiling Mount Type Installation
✽
To attach or detach the camera, refer to the picture.
* Attaching the camera: Hold up the camera and push it to the mount as shown in the
picture. Push the camera until you hear a “click”.
* Detaching the camera:To detach the camera, pull the camera downward while pushing
the unlock buttons on the camera upward.
This guideline is based on the installation of the ceiling flange STB-30PF.
Unlock Button
UNLOCK
To attach the
camera
To detach the
camera
10. Assembling Dome Cover
Once the camera is successfully attached, secure
the mount with the transparent dome cover. Next,
turn on the power.
11. Dome Cover Setting
Once the installation is complete, please optimize
the camera focus settings. On the camera’s OSD
Menu, set the Dome Cover setting to Outdoor.
(Directory: Main Menu/Camera Setting/Others)
STH-380PO
STH-370PO
STH-360PO
STH-370PI
STB-496PPV
STB-30PF
Others
ꢀ
ꢁ
③
ꢂ
ꢃ
Sync
INTERNAL
OFF
Stabilizer
Image Adj
Freeze
OFF
Dome Cover
Outer
15
14
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Pendant Type Installation
Pendant Type Installation
Camera Adaptor
■ 3.3 Indoor Flange Mount Type Installation
Fan Heater Adaptor
(STH-380PO Only)
This guideline is based on the installation of the indoor flange STB-25PF and the
ceiling exposed mount STB-370PC.
Sealing Tape
SPSS32A/SCH40 Size Pipe
STB-30PF
PF 1 1/4"
1. Preparing Pipe and Ceiling Bracket
STB-30PF requires a SPSS32A/SCH40-sized pipe as shown in the picture.Assemble the
screw taps, and then wind a sealing tape around the screw barrel to prevent water leakage.
Please note that the STH-380PO housing requires an additional installation of the fan
heater adapter enclosed with the product.
Notes
ꢀ•ꢀꢀUsingꢀunsealedꢀscrewꢀtapsꢀcanꢀcauseꢀtheꢀproductꢀtoꢀfallꢀdownꢀorꢀallowꢀwaterꢀleakageꢀthatꢀ
may lead to fire or damage the product. Sealing tape is not enclosed with the product, and
needsꢀtoꢀbeꢀpurchasedꢀatꢀyourꢀexpense.
2. Assembling STB-30PF and Pipe
After sealing the screw taps, assemble the STP-30PF flange securely to the pipe.
STB-370PC
STB-30PF
STB-25PF
STB-496PPV
STB-30PF
Notes
ꢀ•ꢀꢀDoꢀnotꢀconnectꢀtheꢀcameraꢀtoꢀaꢀpowerꢀoutletꢀuntilꢀtheꢀinstallationꢀisꢀcomplete.ꢀSupplyingꢀ
power in the middle of the installation may cause fire or damage the product.
✽
For the next installation procedures, refer to the “Wall Type Housing” installation from step 2.
17
16
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Pendant Type Installation
Pendant Type Installation
1. Assembling Flange and Ceiling Exposed Mount (STB-370PC)
Wind sealing tape around the barrel of the screw taps, and then secure the STP-25PF flange
securely to the mount with the enclosed screws.
Notes
ꢀ•ꢀꢀDoꢀnotꢀconnectꢀtheꢀcameraꢀtoꢀaꢀpowerꢀoutletꢀuntilꢀtheꢀinstallationꢀisꢀcomplete.ꢀSupplyingꢀ
power in the middle of the installation may cause fire or damage the product.
4.Wiring Terminal Cables
Connect the cables to the terminal block on the hinged door. Once the wiring is successful,
close the hinged door.
Alignment Directions
Knob
2. Opening Hinged Door
Open the hinged door at the bottom of the housing.
Hold the knob on the hinged door to open.
✽
For the location of the wiring pins, please refer to the “Camera Wiring Diagram” on Page 12.
3. Assembling Mount and Flange
First hook the safety cable on the mount, and then fit the housing into the fixture groove on
the bracket as shown in the picture. Once the housing is safely attached to the bracket,
secure the housing with the enclosed screws.
5. Setting Up Camera DIP Switches
DIP switches for communication and ID protocols are located on the bottom of the camera.
For the switch settings, refer to the appendix of this manual.
ID(SW1)
Protocol(SW2)
CLOSE
19
18
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Pendant Type Installation
On-Ceiling Mount Type Installation
6. Attaching Camera
■ 4. On-Ceiling Mount Type Installation
Carefully attach the camera to the mount following the alignment guide marks as shown in
the picture. First hook the camera's safety cable on the mount, and then attach the camera.
The safety cable is coiled inside the install base.As shown in the leftward picture, pull out
the safety cable from the install base and then hook it to the mount.
This guideline is based on the installation of the indoor flange STB-370PC.
Alignment
Direction
Guides
Safety
Cable
Alignment
Direction
Guides
Alignment
Directions
✽
✽
To attach the camera to the mount, refer to the alignment guide marks as shown in the picture.
Notes
ꢀ•ꢀꢀMakeꢀsureꢀtoꢀfirstꢀhookꢀtheꢀcamera'sꢀsafetyꢀcableꢀtoꢀtheꢀmountꢀbeforeꢀproceeding.ꢀOtherwiseꢀ
youꢀmayꢀbeꢀexposedꢀtoꢀseriousꢀinjuryꢀcausedꢀbyꢀaꢀfallenꢀcamera.
To attach or detach the camera, refer to the picture.
* Attaching the camera: Hold up the camera and push it to the mount as shown in the
picture. Push the camera until you hear a “click”.
* Detaching the camera:To detach the camera, pull the camera downward while pushing
the unlock buttons on the camera upward.
Unlock Button
UNLOCK
STB-370PC
To attach the camera To detach the camera
21
20
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
On-Ceiling Mount Type Installation
On-Ceiling Mount Type Installation
1. Attaching Template and Installing STB-370PC
3. Setting Up Camera DIP Switches
Attach the enclosed template to the ceiling, then drill a hole in the ceiling according to the
diameter marked on the template. Drop the camera cables down from the ceiling through
the hole. Next, install the Install Base STB-370PC to the ceiling as shown in the picture.
Before installing the exposed bracket, open the hinged door at the bottom of the bracket as
shown in the picture. Hold the knob on the hinged door to open.
DIP switches for communication and ID protocols are located on the bottom of the
camera. For the switch settings, refer to the appendix of this manual.
ID(SW1)
Protocol(SW2)
Template
Knob
5. Connecting Camera Safety Cable and Attaching Camera
Carefully attach the camera to the mount following the alignment guide marks as shown
in the picture. First hook the camera's safety cable on the mount, and then attach the
camera.The safety cable is coiled inside the install base.As shown in the leftward picture,
pull out the safety cable from the install base and then hook it to the mount.
Alignment
Direction
Guides
Safety
Cable
Alignment
Direction
Guides
2. Wiring Terminal Cables
Connect the cables to the terminal block on the
hinged door. For the location of the wiring pins,
please refer to the “Camera Wiring Diagram” on
Page 12. Once the wiring is successful, close the
hinged door.
Alignment
Directions
✽
To attach the camera to the mount, refer to the alignment guide marks as shown in the picture.
Notes
Notes
ꢀ•ꢀꢀDoꢀnotꢀconnectꢀtheꢀcameraꢀtoꢀaꢀpowerꢀoutletꢀuntilꢀtheꢀinstallationꢀisꢀcomplete.ꢀSupplyingꢀ
power in the middle of the installation may cause fire or damage the product.
ꢀ•ꢀꢀMakeꢀsureꢀtoꢀfirstꢀhookꢀtheꢀcamera'sꢀsafetyꢀcableꢀtoꢀtheꢀmountꢀbeforeꢀproceeding.ꢀOtherwiseꢀ
youꢀmayꢀbeꢀexposedꢀtoꢀseriousꢀinjuryꢀcausedꢀbyꢀaꢀfallenꢀcamera.
23
22
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
On-Ceiling Mount Type Installation
Indoor Flush Mount Type Installation
✽
To attach or detach the camera, refer to the picture.
* Attaching the camera: Hold up the camera and push it to the mount as shown in the
picture. Push the camera until you hear a “click”.
* Detaching the camera:To detach the camera, pull the camera downward while pushing
the unlock buttons on the camera upward.
■ 5. Indoor Flush Mount Type Installation
This guideline is based on the installation of the flush mount STH-370PE.
Unlock Button
UNLOCK
To attach the
camera
To detach the
camera
STH-370PE
25
24
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Indoor Flush Mount Type Installation
Indoor Flush Mount Type Installation
1. Attaching Flexible Adaptor
Knob
4. Preparing Housing
To feed the cables through a pipe to a flush housing, attach the flexible adaptor enclosed
with the product.To attach the flexible adaptor, the install base must be disassembled as
shown in the picture.To disassemble the install base, unscrew the 3 screws on the
bottom.
Open the hinged door at the bottom of the housing.
While pressing the spring lock (1), hold up the lid to
open (2).
Silicon Cap
Adaptor Nut
Flexible Adaptor
5. Inserting the flush housing
Install Base(STB-370PC)
disassembly
Arrange the cables and eyebolts as shown in the picture, and then insert the housing into
the ceiling hole.
Hanger Bolt
Eyebolt
Eyebolt
2. Attaching Template
Elbo bracket
Fixing Nut
Attach the enclosed template to a desired location on the ceiling. Drill 3 holes of 50 mm
diameter in 120-degree intervals following the marks on the template, and then drill one
200 mm hole in the center of the template.
3. Wiring and Arranging Anti-fall Eyebolts
Attach the enclosed turnbuckle and eyebolts inside the ceiling, and then drop the camera
cables down from the ceiling through the hole.
Turnbuckle
6. Securing Screws or Internal Supports
Two fixture methods are available for the flush mount: screw through or inner support.
Depending on the situation, select one of the two methods.
The inner support method unfolds the supports inside the mount when 3 screws on the
mount surface are fastened.
Eyebolt
Template
Φ200 mm
Template
Ceiling
Notes
ꢀ•ꢀꢀDoꢀnotꢀconnectꢀtheꢀcameraꢀtoꢀaꢀpowerꢀoutletꢀuntilꢀtheꢀinstallationꢀisꢀcomplete.ꢀSupplyingꢀ
power in the middle of the installation may cause fire or damage the product.
ScrewThroughType
Inner SupportType
27
26
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Indoor Flush Mount Type Installation
Indoor Flush Mount Type Installation
7.Arranging Camera Cables and Closing Hinged Door
Connect the cables to the terminal block on the hinged
door.
Notes
ꢀ•ꢀꢀMakeꢀsureꢀtoꢀfirstꢀhookꢀtheꢀcamera'sꢀsafetyꢀcableꢀtoꢀtheꢀmountꢀbeforeꢀproceeding.ꢀOtherwiseꢀ
youꢀmayꢀbeꢀexposedꢀtoꢀseriousꢀinjuryꢀcausedꢀbyꢀaꢀfallenꢀcamera.
For the location of the wiring pins, please refer to the
“Camera Wiring Diagram” on Page 12.
Once the wiring is successful, close the hinged door.
10.Assembling Dome Cover
Once the camera is successfully attached, secure the
mount with the transparent dome cover.
8. Setting Up Camera DIP Switches
DIP switches for communication and ID protocols are located on the bottom of the
camera. For the switch settings, refer to the appendix of this manual.
ID(SW1)
Protocol(SW2)
Notes
ꢀ•ꢀꢀBeꢀcarefulꢀtoꢀnotꢀscratchꢀtheꢀtransparentꢀcoverꢀ
during the assembly. Scratched dome covers
mayꢀdecreaseꢀtheꢀgraphicsꢀqualityꢀandꢀoverallꢀ
performance of the camera.
CLOSE
OPEN
9. Attaching Camera
Carefully attach the camera to the mount following the alignment guide marks as shown
in the picture. First hook the camera's safety cable on the mount, and then attach the
camera.The safety cable is coiled inside the install base.As shown in the leftward picture,
pull out the safety cable from the install base and then hook it to the mount.
✽
To attach or detach the camera, refer to the picture.
* Attaching the camera: Hold up the camera and push it to the mount as shown in the
picture. Push the camera until you hear a “click”.
* Detaching the camera:To detach the camera, pull the camera downward while pushing
the unlock buttons on the camera upward.
Alignment
Direction
Guides
Unlock Button
Safety
Cable
Alignment
Direction
Guides
UNLOCK
Alignment
Directions
To attach the
camera
To detach the
camera
✽
To attach the camera to the mount, refer to the alignment guide marks as shown in the picture.
29
28
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Mounting Accessory Installation
Mounting Accessory Installation
■ 6. Mounting Accessory Installation
■ STB-270B(Setup Box)
MOUNT CAP
This guideline is to be used for the installation of mounting accessories for the
Samsung Speed Dome Camera series.
1. Using self drilling screws, secure the install
bracket.
2. Fill unwanted wire holes with mount caps.
Secure the mount cap with the mount cap
fastener.
MOUNT CAP
FASTENER
3. Place the setup box on the install bracket
as shown in the picture.
STB-350PPM
STB-330PPM
4. Using hexagon bolts, fasten the setup box
to the bracket. Next feed the camera
cables into the setup box through the hole
in the cover.
5. Feed the camera cables through the wall
bracket and secure the bracket using 4
screws.
6. Lastly, fasten the screws using a hexagon
wrench to secure the bracket to the setup
box.
STB-340PCM
STB-270B
31
30
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Mounting Accessory Installation
Mounting Accessory Installation
■ STB-350PPM (Parapet Mount)
Compatible Models : STB-30PF+STH-380PO/370PO/360PO/370PI
■ STB-330PPM (Paul Mount)
Compatible Models : STB-270PWV+STH-380PO/370PO/360PO/370PI
Wall type mount
1. Secure the pole to the mount using a wire or cable.
2. Use 4 1/4" screws to secure the STH-270PWV pole
mount to the wall.
1. Drill 8 anchor bolt holes on the wall according to
the holes in the parapet mount.
2. Using a tool, insert anchor bolts and then set the
parapet mount on the bolts. Use 8 nuts to fasten
the bolts.
1/4" SCREW : 4EA
Parapet mount
Anchor bolt 8EA
■ STB-340PCM (Corner Mount)
3. Feed the cable through the pipe to the other end
Compatible Models : STB-270PWV+STH-380PO/370PO/360PO/370PI
of the pipe.
4. Set PPE on the parapet mount.
PIPE
1. Drill 8 anchor bolt holes on the wall according to the
holes in the corner mount.
Anchor bolt 8EA
Corner mount
2. Using a tool, insert anchor bolts and then set the
corner mount on the bolts. Use 8 nuts to fasten the
bolts.
5.Wind the cable to the direction shown in the
picture, and then assemble the PPE cover using
screws.
6.Adjust the pipe direction, and then secure the pipe
using screws.
3. Use 1/4" screws to secure the STH-270PWV to the
corner.
Wall type mount
7. Install the camera.
1/4" SCREW : 4EA
33
32
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Product External Dimensions
Product External Dimensions
Unit : mm
Unit : mm
■ Wall Mounting
■ Ceiling Mounting
■
Ceiling Exposed Mounting
■
Indoor Flush Mounting
35
34
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
Product Specifications
Product Specifications
Model
Model
STH-380PO
STH-370PO
STH-370PI
STH-370PE
STH-360PO
STH-270PWV
STB-496PPV
STB-370PC
STB-25PF
STB-270B
Item
Item
Operating
Temperature
Range
Operating
Temperature
Range
℃
℃
℃
℃
℃
℃
℃
℃
℃
℃
-40 ~50
-40 ~50
-10 ~50
-10 ~50
-40 ~50
℃
℃
℃
℃
℃
℃
℃
℃
℃
℃
-40 ~50
-20 ~50
-10 ~50
-10 ~50
-20 ~50
0 to 90%RH
(non-condensing)
0 to 90%RH
(non-condensing)
Ceiling
ALDC 12
Flange
Ceiling
Pipe
Ceiling
Bracket
Ceiling
Plate
0 to 90%RH
(non-condensing)
On-Ceiling
Installation
0 to 90%RH
(non-condensing)
Housing
E.G.I 2.0t
Flange
Adaptor
Housing
1 to 90%RH
(non-condensing)
0 to 90%RH
(non-condensing)
Housing
Outdoor
1 to 90%RH
(non-condensing)
Embedded
Housing
Humidity
Humidity
0 to 90%RH
0 to 90%RH
0 to 90%RH
DOOR
ALDC12
PC+ABS
ALDC 12
FRONT
Housing
Outdoor
Housing
Outdoor
Housing
Outdoor
Wall Type
ALDC 12
Mount
ALDC 12
ALDC 12
ALDC 12
ALDC 12
ALDC 12
E.G.I (1.2t)
AL
SPPS32A
/SCH 40
BASE
COVER
AL
ALDC 12
HOUSING
INSTALL
C.R.2.0t
BRACKET
Materials
Components
(mm)
Ring
Ring
Ring
Ring
Ring
Materials
ALDC 12
ABS
ALDC 12
Decoration
Decoration
Decoration
Decoration
Decoration
E.G.I. 2.0t
SPCC
Dome
Cover
Poly
Carbonate
Dome
Cover
Poly
Carbonate
Dome
Cover
Poly
Carbonate
Dome
Cover
Poly
Carbonate
Ceiling
Ceiling
SUS
E.G.I. 2.0t
Bracket
COVER
PC+ABS
Support
JOINT
1EA
MOUNT
SAFETY
WIRE
SUS
Φ
Self Drilling
Self Drilling
Screw
#8xL38
(FZY)
(
1.2x
2000)
PH MS
Screw
(4EA)
Screw
#8xL38
(FZY)
Screw
(4EA)
Screw
(3EA)
BH MS
M3xL6
Screw
M4x8
(3EA)
SUS
MOUNT
5EA
(1EA)
Turn
CAP
Eye Bolt
2EA
Miscellaneous
Components
(mm)
Buckle1EA
-
-
-
-
-
-
-
-
Screw
(3EA)
PH MS
M4xL14
Screw
(3EA)
PH MS
M4xL14
Hexagon
4EA
WIRE
Bolt
-
-
JOINT(4EA)
Silicon
cap(1EA)
Antivibration/
Waterproof
Weight (Net)
Weight (Gross)
Dimensions
(mm)
Operating
Temperature
Range
Screw
(6EA)
#8x38
(FZY)
-
-
-
-
-
DC12V
0.06A
Operating
Temp
More than
℃
45
Less than
DC12V
0.06A
Operating
Temp
More than
45
Less than
10
AC 24V
33W
Operating
Temp
less than
DC12V
0.06A
Operating
Temp
More than
45
Less than
10
AC 24V
33W
Operating
Temp
less than
1.3kg
1.8kg
935g
420g
3kg
1.3kg
2kg
1.4kg
490g
3.3kg
Fan(2EA)
Heater
Fan(2EA)
Heater
-
-
-
-
-
-
-
-
Fan(1EA)
Heater
Φ
270x175x140
150x496
183x48.5
183x37
218x182x92.5
℃
℃
Miscellaneous
℃
10
℃
℃
AC 24V
46W
Operating
Temp
Model
Item
Operating
Temperature
Range
STB-30PF
STB-340PCM
STB-330PPM
STB-350PPM
℃
℃
℃
℃
℃
℃
℃
℃
-40 ~50
-40 ~50
-40 ~50
-40 ~50
less than
℃
10
℃
℃
10
10
0 to 90%RH
(non-condensing)
Ceiling
Flange
Ceiling
Bracket
0 to 90%RH
(non-condensing)
0 to 90%RH
(non-condensing)
0 to 90%RH
(non-condensing)
Humidity
Antivibration/
Waterp
roof
Weight (Net)
Weight
(Gross)
Dimensions
(mm)
IP 67
IP 67
IP 67
-
IP 66
ALDC 12
Corner
Bracket
PF 1 1/4
(32A)
SPCC
Pole Bracket
SPCC
Parapet Pipe
Materials
Components
(mm)
3.2kg
4.2kg
3.2kg
4.2kg
3.2kg
4.1kg
740g
2.1kg
3.2kg
E.G.I. 2.0t
1.2kg
Parapet Plate
Pipe Cover
Set Anchor-6
(8EA)
SUS
SUS
Φ
Φ
Φ
Φ
Φ
242x284.5
242x284.5
242x284.5
242x284.5
190x188.5
Screw
(3EA)
PH MS
M4xL14
Screw
(4EA)
Screw
(4EA)
1/4"
1/4"
1/4"
1/4"
Miscellaneous
Set Anchor-6
(8EA)
Screw
(2EA)
M16x20(SUS)
Antivibration/
Waterproof
Screw
(2EA)
PH MS
M13x10(SUS)
Weight (Net)
Weight (Gross)
Dimensions (mm)
-
-
-
-
380g
1.3kg
580g
8kg
Operating
Temperature
Range
126x66
306x194x185
185x155x48
680x930x63
37
36
SPEED DOME CAMERA ACCESSORIES
SPEED DOME CAMERA ACCESSORIES
MEMO
MEMO
|