Thank you for purchasing the Samsung Bluetooth
Mono Headset WEP200, we hope you will be
delighted with its operation.
Take a moment before you get started to
familiarize yourself with your new headset.
Make sure you have the following items with your
headset:
Before using your headset
Check the accessories
Charge your headset
3
4
Plug the travel adapter into the electrical
outlet.
Charge the headset's battery fully before using
the headset for the first time.
• For Set 1, use the travel adapter provided.
• Charge the headset until the red light on the
headset turns to blue.
• The headset will be fully charged in
approximately 2 hours.
Quick Start Guide
1
Put the headset in the supplied charging case
and close the cover.
Set 1:
Bluetooth Mono Headset
Charging case, Travel adapter, Manual,
2 headset hooks
WEP200
Get connected in 4 quick steps
Remove the travel adapter from the case.
Set 2:
Multi-Function button
Charge your headset
Charging case, Manual, 2 headset hooks
For Set 2, use your phone charger as a
power source for recharging.
NOTE:
Put your headset in pairing mode
Turn on Bluetooth on your phone and
pair with headset
The headset cannot be used while charging.
Hook
Indicator light
Volume control
buttons
Microphone
Test and use
NOTE:
2
Plug the travel adapter into the case's
charging socket.
Your headset supports the headset and/or hands-free
profile(s).
Charging contact
Start here
Put your headset in
pairing mode
Turn on Bluetooth on your
phone and pair with headset
Test and use
Your phone and headset are now paired and
ready to make and receive calls. To confirm
they are operating properly, make a call:
Before you can use your headset, you must pair it
with your phone.
1
Set your Bluetooth phone to discover the
headset by following your phone's guide.
Using your WEP200
Headquarters:
1301 East Lookout Drive Suite 150
Richardson, TX 75082
1
Place the headset over your ear.
See Wearing the headset on the reverse
side of this guide.
Typically, the steps involve going to the Settings,
Connection, or Bluetooth menu on your
phone and then selecting the option to discover
Bluetooth devices.
1
2
Ensure that the headset is off (see Turn
headset on/off on the reverse side of this guide).
See Features and Functions Guide
on the reverse side of this guide
for information on using your
WEP200.
Internet Address:
accessories
Press and hold the Multi-Function button until
the indicator light turns on in blue
(approximately 8 seconds).
2
3
On your phone, make a call to the number
you want.
Your phone will find the Samsung WEP200
headset.
If your phone and headset are successfully
paired, you will hear ringing on the headset.
Customer Care Center:
1-888-987-4357
2
3
Select Samsung WEP200.
After you have successfully paired your phone
and headset, you do not need to repeat these
initial setup steps each time you use the
headset.
When the phone asks if you want to pair with it,
confirm by selecting Yes or OK.
The indicator light flashes in blue as you press and
hold the Multi-Function button. Continue holding
down the button until the blue light is steadily lit.
4
Enter the headset passkey or PIN, 0000.
Guide No.: GH68-11254A
09/2006. Rev. 1.2
Turn headset on/off
Wear the headset
Change for use on other ear
Features and
Troubleshooting
To turn the headset on,
Wear the headset on your ear.
In general, you will get better performance
when there are no obstructions
(including parts of your body)
between the headset
Depending on which ear you are going to wear the
headset, simply adjust the hook accordingly.
Functions Guide
Press and hold the Multi-Function button for
4 seconds until you see 4 blue flashes on the
indicator light, then release.
You will hear a tone and see the indicator light
flashes while the power is on
My phone does not find my headset.
Make sure the blue indicator light on your
headset turns on when your phone is
searching for devices.
SAMSUNG
Bluetooth Mono Headset
WEP200
and the phone.
(see Meaning of the indicator light of this guide).
My headsest worked before but now it is
not working.
To turn the headset off,
Make sure your phone is on and the Bluetooth
feature is turned on in your phone.
If the Bluetooth feature has been turnned off
or was turned on only temporarily, you may
need to restart the Bluetooth feature.
If you have confirmed the Bluetooth feature is
on in your phone, pair your phone and
headset again.
ꢀ
Left
ꢀRight
Press and hold the Multi-Function button for
4 seconds until you see 2 blue flashes on the
indicator light, then release.
You will hear series of 2 tones and see the indicator
light stops flashing.
Important:
Adjust the volume
Be sure to first follow the
Quick Start Guide on
the reverse side of this guide
to complete initial setup
of your headset.
Press [ꢀ] on the side of the headset to increase
the volume level and press [ꢁ] to decrease the
volume level.
Make calls
Use enhanced features
Enhanced features are available for phones that support the
hands-free Bluetooth profile and enhanced features.
Meaning of the indicator light
2
3
Press and hold the Multi-Function button to access the
recent call list.
Press and hold the Multi-Function button to make a call
to the last number you have dialed or received.
Light
Status
Tone
Making a voice activated call
If the phone’s voice recognition feature is on, you can
make a voice activated call.
Press the Multi-Function button once. You will hear the
voice-activation tone.
Say the name of the person you wish to call.
Depending on your phone, this feature may not be
supported.
Flashes in
blue every
8 seconds.
Quick series
of 2 tones.
(Active mode
starts.)
The headset is in Active mode.
• Answer a second call (switching between 2 calls)
• The headset has an active
call in progress.
• You can talk up to 4 hours.
End a call
Press the Multi-Function button once.
When your phone notifies you of another incoming call while
you are on a call, press and hold the Multi-Function button for
2 seconds.
You can switch between calls by pressing and holding it for
2 seconds.
Headquarters:
1301 East Lookout Drive Suite 150
Richardson, TX 75082
Flashes in
Quick series
The headset is in Standby mode.
Answer a call
• After you hear the ring tone, press the Multi-Function
button once.
• If you answer the call with your phone, you can transfer
the call to the headset by pressing the Multi-Function
button.
blue every 3 of 2 tones.
Internet Address:
accessories
• The headset is waiting
for a call.
• The headset can be in
Standby mode up to 70
hours.*
Depending on your phone, this feature may not be supported.
seconds.
(Standby
mode starts.)
Redialing the last number
If the phone’s voice recognition feature is off, press and
hold the Multi-Function button for 2 seconds, twice.
• Place a call on hold
While you are on a call, press and hold the Multi-Function
button for 2 seconds.
To retrieve the call, press and hold the Multi-Function button
for 2 seconds again.
Depending on your phone, this feature may not be supported.
Customer Care Center:
1-888-987-4357
If the phone’s voice recognition feature is on,
Flashes in
red instead
of blue.
5 tones every The battery of the headset is
Reject a call
20 seconds.
low. Recharge the battery.
1
Press the Multi-Function button and listen for the
voice-activation tone. When you hear it, press the
button again to cancel the feature.
When you receive a call, press and hold the Multi-Function
button for 2 seconds to reject the call. Depending on your
phone's setting or type, you may only be able to mute the
ringer or this feature may not be supported.
• There is only 1 minute of
talk time left.
• Switch off the microphone
Press and hold the Up volume control button to switch off the
headset's microphone.
*
Depending on the phone type and usage, the actual time
may vary.
To switch it back on, press and hold the button again.
|