Ultra High Resolution Camera SCB-2000 User Guide
Before installing and operating this product,
please read this manual thoroughly.
ENGLISH
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before operating the camera, confirm the camera model and correct input
power voltage. In order to that you can understand this manual thoroughly,
we will explain the model pert numbers.
n SCB-2000 SERIES
• NTSC MODEL
SCB-2000N
• PAL MODEL
SCB-2000P
SCB-2000ND
SCB-2000PD
SCB-2000PH
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
n MODEL DESCRIPTION
• SCB-2000XX
__
POWER SOURCE
SIGNAL SYSTEM
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
• SIGNAL SYSTEM
N → NTSC MODEL
P → PAL MODEL
INFORMATION-This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
• POWER SOURCE
→ AC 24V / DC 12V
D → DC 12V
H → AC 230V
WARNING : Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
WARNING : To prevent electric shock and risk of fire hazards:
◆
◆
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
Contents
Features
SSDR
•
•
•
•
•
•
Features ………………………………………………………………………… 5
Warnings & Cautions ……………………………………………………… 6
Precautions …………………………………………………………………… 7
Components and Accessories …………………………………………… 8
Overview………………………………………………………………………… 9
Installation …………………………………………………………………… 10
High Resolution
(Samsung Super Dynamic Range)
For images with high contrast between
bright and dark areas from difficult lighting
conditions such as backlighting, this camera
selectively illuminates darker areas while
retaining the same light level for brighter
areas to even out the overall brightness.
By adopting a diagonal 6mm(1/3") 410,000
(NTSC) pixel, 470,000(PAL) pixel SONY CCD,
the camera produces clear picture quality with
a horizontal resolution of 600 TV lines for color.
Excellent Sensitivity
DIS (Digital Image Stabilizer)
The DIS function compensates for any camera
movement, to produce more stable pictures.
The built-in high sensitivity COLOR CCD
produces a clear image even in
0.05Lux(COLOR), 0.0001Lux(SENS-UP) or
lower illumination.
n
LENS………………………………………………………………………………………… …10…
…
n Connecting to the Monitor… ………………………………………………………… …12…
n Using Coaxial Communications……………………………………………………… …13…
n Connecting to the Power……………………………………………………………… …14
Video/DC Drive Lens Support
SSNR3 (Samsung Super Noise
Reduction) Function
…
You can select Video or DC Drive Lens from
the menu.
•
Operating your Camera …………………………………………………… 15
n Menu Configuration……………………………………………………………………… …15…
n Menu Setup… …………………………………………………………………………… …15…
The high-performance W-V DSP chip
effectively removes low-light gain noise and
afterimage to provide clear images even in
dark environments.
Communication
…
…
…
…
…
…
…
…
…
…
Coaxial communication methods are
supported.
- Protocol : Pelco Coaxitron
•
•
•
•
•
•
•
•
•
…
…
…
…
…
…
…
…
…
LENS……………………………………………………………………………………… …16…
EXPOSURE… …………………………………………………………………………… …17…
WHITE BALANCE… …………………………………………………………………… …19…
SSDR……………………………………………………………………………………… …20…
BACKLIGHT……………………………………………………………………………… …20…
SSNR3… ………………………………………………………………………………… …22…
DAY/NIGHT… …………………………………………………………………………… …23…
SPECIAL… ……………………………………………………………………………… …24…
EXIT… …………………………………………………………………………………… …28
Electrical Day&Night
Miscellaneous Functions
The camera automatically identifies when it is
either day or night time and switched
accordingly. During daylight the camera will
switch to color to obtain excellent image
clarity, while at night the camera will switch to
monochrome to obtain improved picture
definition.
HLC(High Light Compensation), SENS-UP, FLIP
(H/V-REV), D-ZOOM, SHARPNESS, MOTION
DETECTION and PRIVACY functions are provided.
OSD
The camera’s OSD is complimented by 18
languages.
•
•
Troubleshooting ……………………………………………………………… 29
Motion Detection
- NTSC : Korean, English, French, Spanish,
Japanese, Portuguese, Taiwanese
- PAL : English, French, German, Spanish,
Italian, Chinese, Russian, Czech,
Polish, Romanian, Serbian, Swedish,
Danish, Turkish, Portuguese
Specifications…………………………………………………………………… 30
Since the camera detects motion without any
additional external sensor, you can monitor
activity more efficient.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
4
5
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to provide
customers with more environment-friendly products.The Eco mark represents
Samsung Techwin’s will to create environment-friendly products, and indicates
that the product satisfies the EU RoHS Directive.
Precautions
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
Warnings & Cautions
This information is provided to ensure your safety and to prevent any losses, financial or otherwise. Please read it
carefully and use the product accordingly.
Use only under temperature conditions between
-10ºC and +50ºC. Provide good ventilation when
using in high temperature conditions.
May lower image quality.
* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as
an aerial ladder while providing after-sales service shall be at your expense.
* Separate the power plug during a thunder storm.
* This product is only part of a surveillance system. Therefore, we can't compensate for material loss and personal
injuries by robbery, fire, natural disaster or something like this type.
Do not install under unstable
lighting conditions.
Avoid touching the camera lens.
Warning/Attention/Special Mark Messages
Ignoring this information may result in
Ignoring this information may result in
material loss and serious personal
material loss and a slight injuries.
injuries including death.
Severe lighting changes or flickering may hinder
normal camera operation.
The lens is the most important component of
the camera. Be careful not to smear it with
fingerprints.
Indicates “Never Allowed.”
Indicates “No Disassembling.”
Do not drop the camera or subject
it to physical shock.
Never keep the camera face to
strong light directly.
May cause a product malfunction.
May damage the CCD.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
6
7
Precautions
Overview
Do not expose the camera to rain
or other types of liquids.
Do not expose the camera to
radioactivity.
Front View
Side View
5
4
3
2
1
May cause a product malfunction.Wipe dry any
liquids. Liquids may contain minerals that are
corrosive to electronic components.
Radioactivity exposure may damage the CCD.
1
2
3
…C…CD protection cap
…C-Mount lens adaptor : Please install this adapter when using a C-Mount Lens.
…CS-Mount lens adaptor : Please remove the C-MOUNT lens adaptor and then attach it.
: Please cover the CCD SENSOR when not using it.
Notes
4
…
B
ack Focus clamp screw : Please loosen the clamp screw with a screwdriver before
• Exposure to the spotlights or objects reflecting bright light, smearing or blooming may
occur.
• Ensure that the power source complies with normal specifications before connecting it to
adjusting the Back Focal length.
5
…
Auto Iris Lens Connector
the camera.
Bottom View
6
6
…T…ripod Mounting Bracket Screw Hole
Used to fix the camera on a bracket or tripod.
The screw sizes for this hole are as follows:
Components and Accessories
1…
2
3
4
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
1
2
3
4
Ultra High Resolution Camera SCB-2000
Auto iris lens connection plug
C-Mount adaptor
You can separate the Tripod Mounting Bracket and install it on the top or
bottom of the camera. Make sure to use the Tripod Mounting Bracket when
fixing the camera to a bracket or tripod. Otherwise the camera may not be
secure, or the internal circuitry of the camera may be damaged.
Instruction manual
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
8
9
Overview
Installation
When Using Auto Iris Lens
Rear View
1. Strip the insulation of the auto iris lens
cable 8mm from the end.
2. Strip the insulation of the core of the auto
iris lens cable to expose a 2mm length.
2mm
7
8
8mm
9
❿
3. Remove the cover of the auto iris lens connector plug and solder the lens cable to the
connector pin of the plug.
*High Voltage Type
7
8
……Power lamp : Lights up when the correct power is supplied to the camera.
……Function Setup Button
LENS
VIDEO
Lens cable
Connector
Pin No.
DC
•SETUP button : Displays the menu on the screen and uses enter sub menu.
•Up&Down button : Used to move the cursor up or down in the menu screen.
•Left&Right button : Used to move the cursor left or right in the menu screen.
……Video output terminal :
Sends video signal and connects to the video input terminal of the monitor.
…Power input terminal : Connects to the power appropriate to each model.
No.1 Pin Damping -
No.2 Pin Damping +
No.3 Pin Drive +
No.4 Pin Drive -
Red (power)
NC
No.3 Pin
No.1 Pin
White (video signal)
Black (GND)
No.4 Pin
No.2 Pin
9
❿
4. Please replace the auto iris lens connection plug cover and take off the CCD protection
cap, and then attach the auto iris lens to the camera by
screwing it in clockwise.
5. Please insert the connection plug that is connected to
the auto iris lens cable into the auto lens connector,
which is located on the side of the camera.
Installation
LENS
The lens is not supplied with this camera. Purchase a lens suitable for your environment.
This camera accepts the auto iris lens and both C-and CS-mount lens.
When using a C-Mount lens
Please take off the CCD protection cap and attach the C-Mount lens to
Notes
the camera by screwing it in clockwise.
C-mount adaptor
• To use the functions of this camera effectively it is recommended that a DC type Auto Iris
lens is used.
• Keep the lens surface clean, if it becomes contaminated with dirt or fingerprints the
picture quality suffers.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
11
10
Installation
• The connection method varies depending on the type of monitor and accessories. Please
refer to the user's manual for each instrument.
When using a CS-Mount lens
• Please turn off the power when connecting.
1. Please take off the CCD protection cap
and C-mount adaptor.
2. Please attach the CS-Mount lens to the
camera by screwing it in clockwise.
Using Coaxial Communications
•Coaxial Communications System
•OSD Control method
C-mount adaptor
CS-mount adaptor
CAMERA
SET
UP
DVR
MENU/ENTER
UP KEY
CONTROLLER
OSD KEY
JOYSTICK UP
DOWN
LEFT
RIGHT
DOWN KEY
LEFT KEY
RIGHT KEY
JOYSTICK DOWN
JOYSTICK LEFT
JOYSTICK RIGHT
CCD protection cap
Notes
DVR
• Please use the specified lens connection parts as shown in the picture below.
The use of the wrong sized parts may cause damage to the inside of the camera or
result in poor fitting.
DVD
• Use of a lens which is too heavy affects the balance of the
camera and may cause a malfunction. Please use a lens
that weighs less than 450g.
: BNC
---- : RS-485
•
•
• Please select Av mode if possible when adjusting the
automatic light control (ALC) of an auto lens. Use of PK
mode may cause hunting.
C-mount lens : 10 mm or less
CS-mount lens : 5 mm or less
•Video Cable
The camera's video output port is connected to the monitor with a BNC coaxial cable,
shown below : If the distance between the camera and the monitor exceeds the
recommended maximum, please use an auxiliary video amp.
Connecting to the Monitor
Please connect the video output terminal located on the back of the camera to the monitor.
Distance
300m
Recommended Cable Specification
3C2V(RG-59/U)
450m
5C2V(RG-6/U)
600m
7C2V(RG-11/U)
Notes
• It is recommended that pure copper coax cable is used and not copper coated steel, as
this will cause issues with the communication over the coaxial cable.
CCD Camera
Monitor
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
13
12
Installation
Operating Your Camera
Connecting to the Power
Menu Configuration
Each model has a different power input specification. Please check the model type and
standard power requirement before connecting to power.
MAIN MENU
●
…
DC
●
…
●
MANUAL
LENS
VIDEO
●
…
●
…………………
● ………
AGC
BRIGHTNESS
SHUTTER
EXPOSURE
AC/DC Power Type
DC Power Type
●
SENS-UP
●
RETURN
●
…
●
…
●
…
ATW
OUTDOOR
INDOOR
• Use AC24V, 300mA adaptor or DC12V,
500mA for SCB-2000N/P
• Use DC12V, 500mA for SCB-2000ND/PD
WHITE BALANCE
●
MANUAL
…
●
AWC→SET
●
…
●
ON
SSDR
OFF
●
…
●
…
●
HLC
BACKLIGHT
SSNR3
OFF
BLC
●
OFF
…
●
ON
●
…
●
…
●
AUTO
DAY/NIGHT
COLOR
B/W
●
…
●
…
●
…
IMAGE ADJ.
MONITOR
CAM TITLE
●
SYNC
●
…
●
PRIVACY
……
SPECIAL
MOTION DET
●
…
●
…
●
RETURN
DIS
LANGUAGE
●
…
●
…
●
RESET
EXIT
SAVE
NOT SAVE
High Voltage Type (AC230V, 50Hz)
Menu Setup
• Use AC230V, 50Hz power source for SCB-
2000PH.
You can set up functions using the 5 buttons on the rear of the camera.
When the resistance value of copper wire is at [20ºC(68°F)]
Copper wire size (AWG)
Resistance (Ω / m)
#24(0.22㎟)
0.078
#22(0.33㎟)
0.050
#20(0.52㎟)
0.030
#18(0.83㎟)
0.018
UP button
SET button
Voltage Drop (V/m)
0.028
0.018
0.011
0.006
LEFT button
DOWN button
RIGHT button
• As shown in the table above, voltage decreases as the wire gets longer.
Therefore use of an excessively long adaptor output line for connection to the camera
may affect the performance of the camera.
1. Press the SET button.
• Main setup menu is displayed on the monitor screen.
*
*…
…
Standard voltage for camera operation : DC 12V±10%, AC 24V±10%, AC 230V ±10% (SCB-2000PH)
There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
15
14
- Level (VIDEO)
:Adjusts the level of video iris signals; the higher the level is,
Operating Your Camera
the brighter the video looks.
- FOCUS ADJ. (DC,VIDEO) :To adjust the DC and VIDEO lens focus correctly, you must
activate the Focus Settings mode under each lens menu.
Activate the Focus Settings mode, adjust the lens focus, and
then deactivate the settings mode. (The VIDEO lens requires
an extra step: go to the sub menu of the Focus Settings
mode and change the shutter speed to adjust the lens
brightness.)
MAIN MENU
Select the function using
the UP or DOWN button.
Change the status using
the LEFT or RIGHT button.
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
4.SSDR
ATW
OFF
OFF
ON
- IRIS SPEED (DC)
:
Adjusts the Iris control speed of the DC lens. If the control speed
is too slow or fast, please use this menu to adjust the speed.
5.BACKLIGHT
6.SSNR3
Notes
7.DAY/NIGHT
8.SPECIAL
9.EXIT
COLOR
•
When using VIDEO lens, adjust the lens VR explained below first and set the focus using
'FOCUS ADJ.' menu.
SAVE
•
•
If color rolling occurs when using a DC lens, set Shutter to A.FLK.
Some lenses may not work properly, depending on the setting of the BRIGHTNESS LEVEL.
• When Using a Video-Type Auto Iris Lens
2. Select a desired function using the Up and Down buttons.
• Place the cursor over a desired item.
3. Set up a selected item by using the Left and Right buttons.
4.To finish the setting, select ‘EXIT’ and press the SET button.
❶……Adjust the ALC adjustment terminal on the lens appropriately. In general, set it to AV
(Average).
2……It may not work properly depending on the installed lens. Set the Level VR of the lens
to the optimal value.
3……Set AGC to OFF and adjust the Lens VR to an appropriate brightness.
4……Adjust the Lens VR, adjust the BRIGHTNESS, and then check if the screen brightness
changes properly. Otherwise, adjust the Lens VR again.
Notes
• An item with the
…
icon also has sub menus. To select a sub menu, select an item with
the icon and press the SET button.
• An item with the - - - icon is unavailable due to function settings.
EXPOSURE
LENS
MAIN MENU
Using this function, you can control the screen brightness.
1.When the SETUP menu screen is displayed, select‘LENS’by using the Up and Down
buttons so that the arrow indicates‘LENS’.
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
ATW
2. Select the connected lens type by using the Left and Right buttons.
1.When the SETUP menu screen is displayed, select‘EXPOSURE’by using the Up and
MAIN MENU
Down buttons so that the arrow indicates‘EXPOSURE’.
1.LENS
DC
2. Select a desired mode using the Up and Down buttons.
2.EXPOSURE
EXPOSURE SETUP
DC/Video : Select Auto Iris Lens
1.BRIGHTNESS
2.SHUTTER
3.AGC
4.SENS-UP
5.RETURN
25
You can adjust the minimum shutter and maximum value of ESC shutter
mode when DC Lens mode is selected.
Manual : Select Manual Lens
ESC
HIGH
OFF
3. Each Lens mode has sub menu items as listed below.
- Brightness (DC, Manual) :Adjusts the video brightness.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
17
16
Operating Your Camera
SHUTTER :You can select either auto or manual shutter.
White Balance (White Bal.)
- ---
: Shutter speed is fixed at 1/60sec(1/50sec).
- A.FLK
: Select this when you experience picture flicker, which can happen when
there is a clash with the frequency of the installed lighting.
: Select this to control the shutter speed automatically. If ESC is selected, the
shutter speed is automatically controlled depending on the ambient
illumination of the subject.
Use the White Balance function to adjust the screen color.
1.When the SETUP menu screen is displayed, select ‘White Bal.’ by using the Up and
Down buttons so that the arrow indicates ‘White Bal.’ .
- ESC
2. Select a desired mode using the Up and Down buttons.
- MANUAL :You can control shutter speed manually. (1/60 ~ 1/120,000)
MAIN MENU
Notes
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
4.SSDR
• When you use a DC lens, set the shutter mode to A.FLK if color rolling occurs.
• When the SHUTTER is set to ESC after selecting the Internal Synchronization Type, the
picture may become unstable if the camera faces a bright fluorescent light. Therefore,
take care when choosing the installation position.
ATW
OFF
• When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
※ Select one of the following 5 modes, as appropriate for your purpose.
ATW
: Select this when the color temperature is between 1,700˚K and
11,000˚K.
AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen - but
the higher the noise.
- OFF : Deactivates the AGC function.
OUTDOOR : Select this when the color temperature is between 1,700˚K and
11,000˚K. (sodium light inclusion)
- LOW :Allows automatic gain control from 5.3dB to 32dB.
- HIGH :Allows automatic gain control from 5.3dB to 37dB.
INDOOR
MANUAL
:
:
Select this when the color temperature is between 4,500˚K and 8,500˚K.
Select this to fine-tune White Balance manually. Set White Balance first by
using the ATW or AWC mode.After that switch to MANUAL mode, fine-
tune the White Balance and then press the SET button.
SENS-UP : When it is night or dark, the camera automatically detects the light level and
maintains a clear picture if this mode is activated.
AWC→SET : To find the optimal luminance level for the current environment, point the
camera towards a sheet of white paper and press the Function Setup switch. If
the environment changes, readjust it.
- OFF : Deactivates the SENS-UP function.
- AUTO :Activates the SENS-UP function.
RETURN : Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.
Notes
Notes
• White Balance may not work properly under the following conditions. In this case select
the AWC mode.
❶……When the color temperature of the environment surrounding the subject is out of the
control range (e.g. clear sky or sunset).
• If you press the SET button in ‘AUTO’ mode, You can adjust brightness by increasing or
decreasing the shutter speed. (x2 ~ x512)
• Note that the higher the zoom level, the brighter the screen, but the more likely it is that an
after-image will appear.
2
…When the ambient illumination of the subject is dim.
• Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation when the
zoom level is increased, this is normal.
3
……If the camera is directed towards a fluorescent light or is installed in a place where
illumination changes dramatically, the White Balance operation may become unstable.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
19
18
Operating Your Camera
SSDR (Samsung Super Dynamic Range)
MAIN MENU
1.LENS
DC
SSDR illuminates darker areas of an image while retaining the same light level for brighter
areas to even out the overall brightness of images with high contrast between bright and
dark areas.
2.EXPOSURE
3.WHITE BAL
4.SSDR
ATW
OFF
OFF
5.BACKLIGHT
MAIN MENU
1.LENS
DC
2. Select a desired mode using the Left and Right buttons depending on the camera purpose.
2.EXPOSURE
3.WHITE BAL
4.SSDR
ATW
OFF
OFF
BLC : Enables a user to select a desired area on a picture and view that area more
clearly.
5.BACKLIGHT
HLC (High Light Compensation) :
If the scene contains extremely bright light areas such as; from car headlight, the light
can mask out much of the on-screen detail.
- LEVEL :Adjust level of the HLC function.
- LIMIT : Enable to change the operating condition.
- MASK COLOR/TONE : Change the color / brightness of the masking area.
(Black, Red, Blue, Cyan, Magenta)
1.When the SETUP menu screen is displayed, select ‘SSDR’ by using the Up and Down
buttons so that the arrow indicates ‘SSDR’.
2. Use the Left/Right buttons to change the SSDR level in the sub menu according to the
contrast between bright and dark areas.
- TOP/BOTTOM/LEFT/RIGHT :Adjust the area to be enhanced.
OFF : Not being used
3. Select a desired mode using the Left and Right buttons and press the SET button.
Select ‘BLC’ to adjust the area to be
enhanced then adjust the level.
HLC : Enable the user to change the level,
limit, mask color/tone and area.
SSDR ON
SSDR OFF
BACKLIGHT
Unlike conventional cameras, the SCB-2000 is designed so that it delivers a distinctive
subject and background at the same time, even when the subject is in backlight, by
adopting a proprietary W-V DSP chip.
1.When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Up and
Down buttons so that the arrow indicates ‘BACKLIGHT’.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
21
20
Operating Your Camera
Notes
DAY/NIGHT
• Because there can be a difference in the effectiveness of HLC according to the amount of
light area in the screen, optimize the installation angle for the best HLC performance.
You can display pictures in color or black and white.
1.When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Up and
Down buttons so that the arrow indicates ‘DAY/NIGHT’.
•
•
When dark, the HLC is only activated when a bright light exceeding a specific size.in NIGHT ONLY mode.
The HLC is not activated in day light or when bright light is not present at night.in NIGHT ONLY mode.
MAIN MENU
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
4.SSDR
ATW
OFF
OFF
ON
SSNR3
This function reduces the background noise in a low luminance environment.
1.When the SETUP menu screen is displayed, select ‘SSNR’ by using the Up and Down
buttons so that the arrow indicates ‘SSNR’ .
5.BACKLIGHT
6.SSNR3
7.DAY/NIGHT
8.SPECIAL
COLOR
MAIN MENU
1.LENS
DC
2. Select a desired mode using the Left and Right buttons according to the picture display you want.
COLOR :The picture is always displayed in color.
2.EXPOSURE
3.WHITE BAL
4.SSDR
ATW
OFF
OFF
ON
B/W
:The picture is always displayed in black and white.
You can turn on or off the burst signal on B/W mode.
5.BACKLIGHT
6.SSNR3
AUTO :The mode is switched to ’Color‘ in a normal
environment, but switches to ’B/W‘ mode
when ambient illumination is low.To set up
the switching time for AUTO mode, press the
SET button.
7.DAY/NIGHT
COLOR
2. Select a desired mode using the Left and Right buttons.
OFF: Deactivates SSNR. Noise is not reduced.
ON :Activates SSNR so that noise is reduced.
You can turn on or off the burst signal on
B/W mode.
- DWELL TIME :You can select the duration time about
changing the day/night mode. …
3. Set the SSNR mode to ‘ON’ and press the SET button.Then you can adjust the noise reduction level.
→5s, 7s, 10s, 15s, 20s, 30s, 40, 60s
Notes
Notes
• When using a Video Auto Iris Lens, if you set the lens level to low, automatic switching
between Color and Black & White may not occur.
•
You cannot set the SSNR to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’.
• When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR'
mode and 'AUTO' mode can not be selected.
• When adjusting the noise reduction level in the SSNR mode, remember that the higher
the level set, the more the noise level will be reduced, as will the brightness of the image.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
23
22
Operating Your Camera
2) Select a desired mode using the Up and Down buttons.
SPECIAL
1.When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Up and Down
buttons so that the arrow indicates ‘SPECIAL’.
IMAGE SETUP
1. V-REV
OFF
2. H-REV
3. D-ZOOM
4. FONT COLOR
5. SHARPNESS
6. RETURN
OFF
OFF
WHITE
ON
MAIN MENU
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
4.SSDR
ATW
OFF
OFF
ON
• V-REV
• H-REV
• D-ZOOM
:You can flip the picture vertically on the screen.
:You can flip the picture horizontally on the screen.
:You can use a digital zoom of x1 ~ x16.
5.BACKLIGHT
6.SSNR3
7.DAY/NIGHT
8.SPECIAL
9.EXIT
COLOR
• FONT COLOR : You can change the OSD font color. (White,Yellow, Green, Red, Blue)
•
SHARPNESS :As you increase this value, the picture outline becomes stronger and
clearer.Adjust this value appropriately depending on the sharpness of
the picture.
SAVE
2. Select a desired mode using the Up and Down buttons.
• RETURN
: Select this to save the settings for the IMAGE ADJ. menu and to
return to the SETUP menu.
SPECIAL
1. IMAGE ADJ
Notes
2. MONITOR
3. CAM TITLE
4. SYNS
5. MOTION DET
6. PRIVACY
7. DIS
LCD
OFF
INT
OFF
OFF
OFF
• When the V-REV or H-REV mode is enabled, the text on the screen does not flip.
• If you increase the SHARPNESS level too high, the picture may become distorted or noise
may appear.
8. LANGUAGE
9. RETURN
ENGLISH
Monitor : Please change the settings value of video
appropriate to your monitor.
- LCD : Please select this menu item when using an LCD
monitor.
- CRT
:
Please select this menu item when using a CRT
monitor.
IMAGE ADJ. :
- USER : Please use this menu item when using a monitor
other than standard ones.You can change the
1) When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the Up
and Down buttons so that the arrow indicates ’IMAGE ADJ‘.
gamma, PED level, and color gain in the sub menus.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
25
24
Operating Your Camera
Notes
•
When using AC power at 60Hz frequency, you can use the L/L type synchronization.
CAM TITLE : If you enter a title, the title will appear on the monitor.
• When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.
1) If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the
arrow indicates ‘CAM TITLE’.
:
MOTION DET
CAMERA TITLE SETUP
2) Set it to ‘ON’ by using the Left and Right buttons.
This product has a feature that allows you to observe
movement of objects in 8 different areas on the screen,
and the words 'MOTION DETECTED' appear on the
screen when movement is detected.
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
3) Press the SET button.
4) Use the 4 direction buttons to move to a
desired letter and select the letter by
- . 0 1 2 3 4 5 6 7 8 9
pressing the SET button. Repeat this to
enter multiple letters. You can enter up to
15 letters.
5) Enter a title, move the cursor to ‘POS’ and press
the SET button. The entered title appears on the
you can monitor activity more efficient.
← → CLR POS END
…1) When the SPECIAL menu screen is displayed, press the Up and Down buttons so
that the arrow indicates‘MOTION DET’.
FRONT DOOR
…2) …Set up the mode using the 4 direction buttons.
screen. Select the position to display the title on
the screen by using the 4 direction buttons and
press the SET button. When the position is
determined, select ‘END’ and press the SET button
to return to the SPECIAL menu.
- SENSITIVITY :You can select up to 8 MD areas.When SENSITIVITY number is high,
motion detection sensitivity is increased to recognize even small
movement.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS
- YPOS
- XPOS
: Determines which of the 4 vertices of each MD area is to be used.
: Determines the coordinate of the vertical axis for SEL POS.
: Determines the coordinate of the horizontal axis for SEL POS.
Notes
• When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even
if you enter one.
• Only English is available in this mode.
• If you move the cursor to CLR and press the SET button, all the letters are deleted. To edit
a letter, change the cursor to the bottom left arrow and press the SET button. Move the
cursor over the letter to be edited, move the cursor to the letter to be inserted and then
press the SET button.
- FILL→SET : Fills in a selected MD area. The color of filling is sequentially selected
as brown, orange, blue, cyan, green, yellow, magenta and red.
- RETURN
: Select this to save the MOTION DET menu settings and return to the
SPECIAL menu.
PRIVACY : Mask an area you want to hide on the screen.
PRIVACY AREA SETUP
SYNC : In areas where the supply is at 60Hz, you can
synchronize the output phase of multiple cameras
using the power synchronization function (Line-
Lock) without using a synchronization signal
generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
• Press the Function Setup switch.
1. AREA
2. MODE
AREA1
OFF
GREEN
1
39
79
3. MASK COLOR
4. MASK TONE
5. TOP
6. BOTTOM
7. LEFT
12
51
8. RIGHT
9. RETURN
• You can select a desired phase from 0 to 359 when select 'phase'.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
27
26
Troubleshooting
Operating Your Camera
1) …When the SPECIAL menu screen is displayed, press the Up and Down buttons so
that the arrow indicates ‘PRIVACY’.
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
…
2…) …Set up the mode using the 4 direction buttons.
●
Nothing appears on the screen.
- AREA SEL
- MODE
:
You can select up to 12 PRIVACY areas.
▶ Check that the power cord and line connectionbetween the camera and monitor are
: Determines whether to use the area selected in the AREA SEL.
fixed properly.
- MASK COLOR : Determine area color.You can select Green, Red, Blue, Black,White, Gray.
- MASK TONE :Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT :Adjust the size and position of the selected area.
▶
Check the type of lens.
▶Check that the lens type is VIDEO lens or DC lens.
● The image on the screen is dim.
- RETURN
: Select this to save the PRIVACY menu settings and return to the SPECIAL
menu.
▶ Is lens stained with dirt? Clean your lens with soft, clean cloth.
▶ Set the monitor to proper condition.
▶ If the camera is exposed to too strong light, change the camera position.
DIS (Digital Image Stabilizer) :
This function mitigates any picture movement due to external factors such as wind.
● The image on the screen is dark.
▶Adjust the contrast feature of the monitor.
▶If you have an intermediate device, set the 75Ω / Hi-z properly.
Notes
● The camera is not working properly, and the surface of the camera is hot.
▶Check that you have properly connected the camera to an appropriate power source.
•
•
•
As the DIS function uses the digital zoom the camera's resolution will decrease.
DIS doesn’t operate when background illumination is too low.
DIS doesn’t operate when object pattern is monotonic as like sky or white wall.
● The SENS-UP function does not work.
▶Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’.
LANGUAGE :You can select the menu language according to your requirements.
● The Motion Detection function does not work.
▶Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’.
RETURN : Select this to save the SPECIAL menu settings and return to the MAIN
SETUP menu.
● Color is not correct.
▶Check the setting of WHITE BAL SETUP menu .
● The screen flickers continually.
▶Check that direction of camera turns toward the Sun.
EXIT
● When coaxial communication is not available:
Select a desired EXIT mode using the Left and Right buttons depending on the camera
purpose.
▶
Make sure that the camera and monitor are installed within the recommended distance.
▶Use the video amplifier equivalent to coaxitron if the recommended installation
- SAVE
: Save the current settings and exit the MAIN SETUP menu.
distance is exceeded.
- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.
- RESET
: Resets the camera settings to the factory defaults. Language and Monitor
settings are not initialized.
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
29
28
Specifications
DECLARATION OF CONFORMITY
Application of Council Directive(s)
2004 / 108 / EC
SCB-2000ND
SCB-2000N
SCB-2000PD
SCB-2000P
SCB-2000PH
ELECTRICAL
Input Voltage
Power Consumption
VIDEO
Imaging Device
Total Pixels
Effective Pixels
Scanning System
Synchronization
Frequency
Horizontal Resolution
Min. Illumination
S/N (Y Signal)
Video Output
OPERATIONAL
IRIS Adustment
Electronic Shutter Speed
On Screen Display
SSDR
Manufacturer's Name
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-716
DC 12V
Max 2.5W
AC 24V / DC 12V
Max 3.5W
DC 12V
Max 2.5W
AC 24V / DC 12V
Max 3.5W
AC 230V, 50Hz
Max 4.0W
1/3 inch, Diagonal 6mm Super HAD CCD
811(H) x 508(V)
768(H) x 494(V)
2:1 Interlace
Internal Only
H : 15.734KHz V:59.54Hz
600TVL
0.05 Lux(50IRE, No SENS-UP) / 0.0001Lux (SENS-UP x512) @F1.2
52dB (Weight Off, AGC Off)
CVBS : 1.0Vp-p, 75Ω composite
795(H) x 596(V)
752(H) x 582(V)
European Representative Name
European Representative Address
Equipment Type/Environment
Model Name
Internal /LineLock
Internal Only Internal / Line-Lock
H: 15.625KHz V: 50.00Hz
CCTV Camera
SCB-2000P, SCB-2000PH, SCB-2000PD
C59W6V3Z200001X
2010.02.01
DC / VIDEO
1/60 ~ 1/120K sec
NTSC : 7 Languages, PAL : 15 Languages
On / Off (Level adjustable)
Beginning Serial NO.
1/50 ~ 1/120K sec
Year of Manufacture
Backlight Compensation
Day & Night
Gain Control
White Balance
SENS-UP (frame Integration)
Motion Detection
Privacy Masking
3D Noise Filter (SSNRIII)
Digital Zoom
BLC / HLC / OFF
COLOR / BW / AUTO (Electric)
Low / High / Off
ATW / OUTDOOR / INDOOR / MANUAL / AWC (1,700°K ~ 11,000°K)
Auto /Off (Selectable x2 ~ x512)
On / Off (8 Programmable zones)
On / Off (12 Programmable zones)
On / Off (Level adjustable)
Conformance to
EN 55022 : 2006
EN 50130-4 : 2003
On / Off (x1 ~ x16)
Digital Image
Stabilization(DIS)
On / Off
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
Camera Title
Sharpness
Flip / Mirror
Off / On (Displayed 15 Characters)
On / Off (Level adjustable)
On / Off
Communication
ENVIRONMENTAL
Operating Temp/Humid
Storage Temp/Humid
MECHANICAL
Lens Mount
Back Focus Adjustment
Dimension
Weight
Coaxial (Protocol : Pelco Coaxitron)
Manufacturer SAMSUNG TECHWIN CO., LTD
Signature
Legal Representative in Europe
-10°C ~ +50°C / 30% ~ 80% RH
-20°C ~ +60°C / 20% ~ 90% RH
Signature
Full Name
Position
Place
Full Name
Position
Place
BONJENG GU
C / CS Mount
Manual
58(W) x 52(H) x 121(D)mm
QUALITY CONTROL MANAGER
CHANGWON, KOREA
2010.02.01
290g
310g
290g
310g
510g
※
The specification for this product may change without prior notice for product improvement.
Date
Date
COLOR CCD CAMERA
User Guide
COLOR CCD CAMERA
User Guide
31
30
|