®
ELECTRIC CHAIN SAW
OWNER’S MANUAL
®
®
MODELS
LNT-2: 076728J, 100089-06, & 099178H
EL-1, EL-1 Fast Sharp
EL-7: 075762J, 098031J, 099039J, 100015,
100089-01, 100089-04, 100089-05, & 100089-07
EL-7 Fast Sharp: 076702J
Pole Saw: 104316-01
Pole Saw Assembly: 104317
IMPORTANT:Readandunderstandthismanualbeforeassemblingor
operating this chain saw. Improper use of saw can cause severe
injury. Keep this manual for future reference.
®
OWNER’S MANUAL
MAINTENANCE AND
STORAGE OF CHAIN SAW
1. Unplug chain saw from power source
• when not in use
SAFETY
WARNINGS
KICKBACK
• before moving from one place to an-
other
WARNING: Kickback may oc-
cur when the nose or tip of the
guide bar touches an object, or
when the wood closes in and
pinches the saw chain in the cut.
Tip contact in some cases may
cause a lightning fast reverse re-
action, kicking the guide bar up
and back towards the operator.
Pinching the saw chain along the
topoftheguidebarmaypushthe
guide bar rapidly back towards
the operator. Either of these re-
actions may cause you to lose
control of the saw which could
result in serious injury to user.
• before servicing
• before changing accessories or at-
tachments, such as saw chain and
guard
Direction
2. Inspect chain saw before and after each
Do Not Let
Guide Bar
Touch Here
use. Check saw closely if guard or other
part has been damaged. Check for any
damage that may affect operator safety
or operation of saw. Check for align-
ment or binding of moving parts. Check
for broken or damaged parts. Do not
use chain saw if damage affects safety
or operation. Have damage repaired by
authorized service center.
90°
Quadrant
3. Maintain chain saw with care.
• Never expose saw to rain.
• Keep chain sharp, clean, and lubri-
cated for better and safer performance.
• Follow steps outlined in this manual
to sharpen chain.
Figure 1 - Kickback Hazard Example: Do
Not Let Nose of Guide Bar Touch Object
While Chain is Moving
Kickback Safety Devices On
This Saw
This saw has a low-kickback chain and
reduced kickback guide bar. Both items
reduce the chance of kickback. Kickback
can still occur with this saw.
• Never try cutting through two logs at
same time. Only cut one log at a time.
• Keep handles dry, clean, and free of
oil and grease.
• Keep all screws and nuts tight.
• Inspect power cord often. If dam-
aged, have repaired by authorized
service center.
• Never carry chain saw by power
cord.
• Never yank power cord to unplug it.
• Keep power cord from heat, oil, and
sharp edges.
• Do not bury guide bar nose or try plunge
cut (boring into wood using guide bar
nose).
Properly install front hand guard. This item
can reduce injuries from kickback. Follow
assembly instructions on page 6. Do not
remove front hand guard. Do not replace
front hand guard with substitute.
• Watch for shifting of wood or other
forces that may pinch chain.
• Use extreme caution when re-entering a
previous cut.
The following steps will reduce the risk of
kickback.
• Use low-kickback chain and guide bar
supplied with this chain saw. Only re-
place these parts with chains and guide
bars listed in this manual.
• Use both hands to grip saw while saw is
running. Use firm grip. Thumbs and
fingers must wrap around saw handles.
• Inspect extension cords often and
replace if damaged.
4. When servicing, use only identical re-
placement parts.
• Never use dull or loose chain. Keep chain
sharp with proper tension.
• Keep all safety items in place on saw.
Make sure they work properly.
5. When not in use, always store chain saw
• in a high or locked place, out of
children’s reach
• Do not hand sharpen chain on automatic
chain sharpening (Fast Sharp) models.
• Do not overreach or cut above shoulder
height.
• Keep solid footing and balance at all
times
• in a dry place
• in a carrying case or with scabbard
over guide bar
Saw Maintenance and Kickback
Safety
• Stand slightly to left side of saw. This
keeps your body from being in direct line
with chain.
Follow maintenance instructions in this
manual. Proper cleaning of saw and chain
and guide bar maintenance can reduce
chances of kickback. Inspect and maintain
saw after each use. This will increase the
service life of your saw. Note: Even with
proper sharpening, risk of kickback can
increase with each sharpening.
Keep this manual for reference. It is your
guide to safe and proper operation of this
chain saw.
• Do not let guide bar nose touch anything
when chain is moving (see Figure 1).
097017
3
®
ELECTRIC CHAIN SAW
Replacement Chain Chain that com-
CHAIN SAW NAMES
AND TERMS
plies with ANSI B175.1 when used with a
specific saw. It may not meet ANSI require-
ments when used with other saws.
Bucking Process of cutting a felled tree or
SawChain(Chain) Loopofchainhaving
cutting teeth for cutting wood. The motor
drives chain. The guide bar supports chain.
log into lengths.
Felling Process of cutting down a tree.
Felling Cut Final cut when felling a tree.
Make this cut on opposite side of tree from
notching cut.
SpikedBumper(Spike) Pointed teeth at
front of saw body beside guide bar. Keep
spiked bumper in contact with wood when
felling or bucking. It helps maintain posi-
tion of saw while cutting.
FrontHandle Locatedatfrontofsawbody.
Front Hand Guard Shield between front
handle and guide bar. Protects left hand
while using saw.
Sprocket Toothedwheelthatdriveschain.
Switch Devicethatcompletesorinterrupts
electrical circuit to motor of saw.
Guide Bar Metal bar that extends from saw
body.Theguidebarsupportsandguideschain.
Switch Linkage This device connects
switch to trigger. It moves switch when you
squeeze trigger.
Guide Bar Nose Tip or end of guide bar.
Kickback Quick backward and upward
motion of guide bar. Kickback may occur
when tip of guide bar touches an object
while chain is moving. The guide bar will
kick up and back towards operator.
Switch Lockout Device that reduces
accidental starting of saw.
Trigger Device that turns saw on and off.
Squeezing trigger turns saw on.
Limbing Process of cutting limb(s) from a
felled tree.
Releasing trigger turns saw off.
Trimming (Pruning) Process of cutting
limb(s) from a living tree.
Low-Kickback Chain Chain that re-
duces chance of kickback as required by
ANSI B175.1.
Undercut An upward cut from underside
of log or limb. This is done while in normal
cutting position and cutting with top of
guide bar.
Normal Cutting Position Stance used
while making bucking and felling cuts.
Notching Cut Notch cut in tree that di-
rects fall of tree.
Oiler Control System for oiling guide bar
and chain.
PowerHead Chainsawwithoutchainand
guide bar. Also known as saw body.
Pushback (Kickback, Pinch) Rapid
pushback of chain saw. Pushback may oc-
curifchainalongtopofguidebarispinched,
caught, or contacts a foreign object.
RearHandle Handlelocatedatrearofsaw
body.
Reduced Kickback Guide Bar Guide
bar that reduces chance of kickback.
097017
4
OWNER’S MANUAL
PRODUCT
UNPACKING
Front Hand
Guard
IDENTIFICATION
1. Remove all items from carton.
Guide Bar
Nose
2. Check all items for any shipping dam-
age. If you find any damage or if any
parts are missing, promptly inform
dealer where you bought chain saw.
Saw
Chain
Rear
Handle
Guide Bar
Spike
Rear Hand
Guard
Scabbard
Power Cord
Oil Level Sight Hole
(located on saw body,
hidden by front handle)
Oil Cap
Front Handle
Switch
Lockout
Trigger
Motor
Housing
Figure 2 - Electric Chain Saw
097017
5
®
ELECTRIC CHAIN SAW
8. Place chain around drive sprocket, then
ASSEMBLY
CAUTION: Do not place chain
on saw backwards. If chain is
backwards,sawwillvibratebadly
and will not cut.
along top groove of guide bar and
around guide bar nose. Note: Make
sure cutting edges of chain are facing
the right direction. Position chain so
cutting edges on top of guide bar face
guide bar nose (see Figure 3).
Note: Some models are pre assembled. As-
sembly is not needed on these models.
See Saw Chain Tension Adjustment, page 7.
9. Adjust saw chain tension. Follow steps
under Saw Chain Tension Adjustment,
page 7.
WARNING: Cutting edges on
chain are sharp. Use protective
gloves when handling chain.
Tapping
Screw
Front Hand
Guard
Towards
Guide
Cutting
Edge
IMPORTANT:Donotclampchain
saw in vise during assembly.
Bar Nose
The plastic hardware bag should include:
• two guide bar bolts
Saw
Chain
Cutting
Edge
• two guide bar nuts
Guide Bar
Bolts
• one Phillips-head tapping screw
• automatic chain sharpener (Fast Sharp
models only)
Drive
Sprocket
1. Lay chain out flat.
Mounting
Stand-Outs
2. Install front hand guard onto saw body.
Do this by pressing two mounting stand-
outs on hand guard into hex-shaped
holes in saw body (see Figure 3).
3
Insert tapping screw through hand
guard and into saw handle. Tighten
screw firmly.
Guide
Bar
4. Turn adjusting screw counterclockwise
(see Figure 4). Continue to turn adjust-
ing screw until adjusting block is to rear
of adjusting plate.
Adjusting
Hole
Guide Bar
Nuts
5. Install guide bar onto saw body. Place
rear of guide bar between adjusting
plate and sprocket support.
IMPORTANT: Make sure to insert ad-
justing block into oval adjusting hole
on guide bar.
Figure 3 - Assembling Guide Bar, Chain, and Hand Guard
6. Line up holes on sprocket support with
center slot on guide bar and holes in
saw body.
Adjusting
Block
Adjusting
Plate
7. Insert guide bar bolts through front
hand guard, saw body, center slot of
guide bar, and sprocket support.Attach
guide bar nuts to guide bar bolts.
Adjusting
Screw
IMPORTANT: Tighten guide bar nuts
finger tight only. Make sure adjust-
ing block is in oval adjusting hole on
guide bar.
Sprocket
Support
Figure 4 - Part Locations For Assembling Guide Bar
097017
6
OWNER’S MANUAL
ASSEMBLY
SAW CHAIN
TENSION
Continued
ADJUSTMENT
INSTALLING AUTOMATIC
CHAIN SHARPENER
WARNING:Unplugchainsaw
frompowersourcebeforeadjust-
ing saw chain tension.
(Fast Sharp Models Only)
1. Screw automatic chain sharpener into
threaded hole.
2. Continue turning automatic chain
sharpener until you hear five (5) clicks.
WARNING: Cutting edges on
chain are sharp. Use protective
gloves when handling chain.
Automatic
Chain
Sharpener
WARNING: Maintain proper
chain tension always. A loose
chain will increase the risk of
kickback.Aloosechainmayjump
outofguidebargroove.Thismay
injure operator and damage
chain. A loose chain will cause
chain, guide bar, and sprocket to
wear rapidly.
PUSH
Figure 6 - Turning Adjusting Screw
SHARPTEON
Guide Bar
Nuts
Note: For pre assembled models, the saw
chain tension is properly set at factory. A
new chain will stretch. Check new chain
after first few minutes of operation. Allow
chain to cool down. Follow steps below to
readjust saw chain tension.
Guide Bar
Figure 5 - Automatic Chain Sharpener
(Fast Sharp Models Only)
1. Before adjusting chain, make sure guide
bar nuts are only finger tight (see Figure
3, page 6). Also make sure adjusting
block is in oval adjusting hole on guide
bar (see Figures 3 and 4, page 6).
Guide Bar
Correct
Tension
Gap
2. Turn adjusting screw clockwise until
all slack is out of chain (see Figure 6).
Note: There should be no gap between
side links of chain and bottom of guide
bar (see Figure 7).
Incorrect
Tension
Figure 7 - Saw Chain Adjustment
3. Wearing protective gloves, move chain
around guide bar. Chain should move
freely. If chain does not move freely,
loosen chain by turning adjusting screw
counterclockwise.
FILLING OIL TANK
1. Remove oil cap.
2. Fill oil tank with SAE #30 motor oil.
Note: For temperatures below 30°F, use
SAE #10 oil. For temperatures above
75°F, use SAE #40 oil.
3. Replace oil cap at once. Tighten oil cap
firmly for good seal. This will avoid oil
seepage from tank.
4. After chain tension is correct, tighten
guide bar nuts firmly. If not, guide bar
will move and loosen chain tension.
This will increase the risk of kickback.
This can also damage saw. Note:Anew
chain will stretch. Check new chain
after first few minutes of operation.
Allow chain to cool down. Readjust
chain tension.
4. Wipe off excess oil.
Note: It is normal for oil to seep when saw
is not in use. Empty oil tank after each use to
prevent seepage.
097017
7
®
ELECTRIC CHAIN SAW
5. When ready to make a cut, press in
switch lockout with right thumb and
squeeze trigger (see Figure 10). This
will turn saw on. Releasing trigger will
turn saw off. Make sure saw is running
at full speed before starting a cut.
OILING CHAIN
OPERATING CHAIN
Always check oil level before using saw. To
SAW
oil chain, press oil cap. Do not attempt to
operate the oiler while cutting with the saw.
Oil will feed onto guide bar and chain. Press
oilcapatleastoncebeforeeachcut.Checkoil
level often by looking at oil sight level hole.
Oil sight level hole is on left side of saw,
between front handle and front hand guard.
WARNING: Read and under-
stand this owner’s manual before
operating this saw. Make certain
youreadandunderstandallSafety
Warnings,pages2and3.Improper
use of this chain saw can cause
severe injury or death from fire,
electrical shock, or body contact
withmovingchain,orfallingwood.
Switch
Lockout
EXTENSION CORDS
Use proper extension cords with this saw.
Use only extension cords marked for out-
door use. The cord must be marked with
suffix W or W-A following the cord type
designation. Example: SJTW-A or SJTW.
Trigger
Figure 10 - Switch Lockout and Trigger
Location
Figure 9 - Pressing Oil Cap to Oil Chain
Use proper sized cord with this saw. Cord
must be heavy enough to carry current
needed. An undersized cord will cause volt-
age drop at saw. Saw will lose power and
overheat. Follow cord size requirements
listed below.
6. When starting a cut, place moving
chain against wood. Hold saw firmly
in place to avoid possible bouncing or
skating (sideways movement) of saw.
CUTTING WITH THE CHAIN
SAW
1. Connect saw to extension cord. Con-
nect extension cord to power supply.
7. Guide saw using light pressure. Do not
force saw. The motor will overload and
can burn out. It will do the job better and
safer at the rate for which it was intended.
Cord
Length
AWG Cord
Size
2. Make sure section of log to be cut is
not laying on ground. This will keep
chain from touching ground as it cuts
through log. Touching ground with
moving chain will dull chain.
25 feet
50 feet
100 feet
16
16
14
12
8. Remove saw from a cut with saw run-
ning at full speed. Stop saw by releas-
ing trigger. Make sure chain has
stopped before setting saw down.
150 feet
3. Use both hands to grip saw.Always use
left hand to grip front handle and right
hand to grip rear handle. Use firm grip.
Thumbs and fingers must wrap around
saw handles (see Figure 10).
9. Practice until you can maintain a steady,
even cutting rate.
Keep cord away from cutting area. Make
sure cord does not catch on branches or logs
during cutting. Inspect cords often. Replace
damaged cords.
4. Make sure your footing is firm. Keep
feet apart. Divide your weight evenly
on both feet.
The extension cord may come undone from
the power cord during use. To avoid this,
make a knot with the two cords as shown in
Figure 8 below.
Chain Saw
Power Cord
Extension
Cord
Figure 8 - Tying Extension Cord and
Power Cord in Knot
097017
8
OWNER’S MANUAL
Direction
of Fall
OPERATING CHAIN
Retreat
Path
SAW
Hinge
Direction
of Fall
3rd Cut -
Felling Cut
Continued
2nd Cut -
Upper
Notch Cut
FELLING A TREE
(Cutting Down a Tree)
2
Inches
45°
2"
WARNING:
1st Cut -
Lower
Notch Cut
Retreat
Path
Tree
• Avoid kickback. Kickback can
resultinsevereinjuryordeath.
See Kickback, page 3 to avoid
risk of kickback.
Figure 11 - Retreat Path From Tree
Felling Procedure
A) Felling Notch
• Donotfellatreewithoutample
skill or expert help.
• Keep children, animals, and
bystanders away from area
when felling a tree.
• If two or more persons perform
bucking and felling operations
A properly placed felling notch will deter-
mine direction tree will fall. Place felling
notch on side of tree in direction you want
tree to fall (see Figure 12). Follow direc-
tions below to create a felling notch.
Figure 12 - Felling A Tree
3. As felling cut nears hinge, tree should
begin to fall. Note: If needed, drive
wedges into felling cut to control di-
rection of fall. If tree settles back and
pinches chain, drive wedges into fell-
ing cut to remove saw. Only use wedges
made of wood, plastic, or aluminum.
Never use wedge made of steel. This
could cause kickback and damage to
chain.
1. Make lower notch cut as close to
ground as possible. Hold saw so guide
bar is horizontal. Cut 1/3 the diameter
of tree trunk (see Figure 12). Note:Al-
ways make this horizontal lower notch
cut first. If you make this cut second,
tree can pinch chain or guide bar.
WARNING: When felling a
tree, be aware of your surround-
ings. Do not endanger any per-
son, strike utility lines, or cause
property damage. If tree strikes
utility lines, contact utility com-
pany at once.
4. When tree begins to fall, quickly
• remove saw from felling cut
• release trigger to turn saw off
• put saw down
2. Start upper notch cut the same distance
above first cut as first cut is deep.
Felling is the process of cutting down a tree.
Make sure your footing is firm. Keep feet
apart. Divide your weight evenly on both
feet. Follow directions below to fell a tree.
Example: If lower notch cut is eight
inches deep, start upper notch cut eight
inches above it. Cut downward at 45°
angle. The upper notch cut should meet
end of lower notch cut (see Figure 12).
• exit area using retreat path
Before Felling a Tree
WARNING: Be alert for falling
overheadlimbs.Watchyourfoot-
ing while exiting area.
3. Remove tree trunk wedge created by
notching cuts.
1. Before felling, inspect tree. Make sure
there are no dead limbs or branches that
may fall on you. Study natural lean of
tree, location of larger branches, and
B) Felling Cut
wind direction. This will help you judge 1. Make felling cut two inches higher than
which way tree will fall.
lower notch cut and on opposite side
of tree (see Figure 12). Keep felling cut
parallel to lower notch cut.
2. Clear work area around tree.
3. Plan and clear a retreat path before fell-
ing. Make retreat path opposite to
planned direction of fall of tree and at
45° angle (see Figure 11).
4. Remove dirt, stones, loose bark, nails,
staples, and wire from tree where you
will make felling cuts.
2. Cut towards notch.
WARNING: Do not cut all the
way through tree. Leave about
two inches of tree diameter un-
cut directly behind felling notch
(see Figure 12). This uncut por-
tion acts as a hinge. The hinge
helpskeeptreefromtwistingand
falling in wrong direction.
5. Stay on uphill side when felling tree.
Tree could roll or slide downhill after
falling.
Continued
097017
9
®
ELECTRIC CHAIN SAW
Entire Length Of Log On
Ground
Cut log from top (see Figure 14).
BUCKING A LOG
OPERATING CHAIN
SAW
WARNING: Avoid kickback.
Continued
Kickback can result in severe in-
juryordeath.SeeKickback,page
3 to avoid risk of kickback.
LIMBING A TREE
WARNING: Avoid kickback.
WARNING:
Kickback can result in severe in-
juryordeath.SeeKickback,page
3 to avoid risk of kickback.
• If on slope, make sure log will
not roll down hill. Secure log
byusingwoodenstakes. Drive
wooden stakes into ground on
downhill side of log. Stand on
uphill side of log while cutting.
Log may roll after cutting.
• Never try cutting through two
logs at same time. This could
increase the risk of kickback.
• While cutting log, never hold
logwithyourhand,leg,orfoot.
• While cutting log, never allow
another person to hold log.
• Turn off and unplug saw be-
fore moving from one place to
another.
WARNING:Whencuttinglimb
thatisundertension,useextreme
caution.Bealertforwoodspring-
ing back. When wood tension is
released, limb could spring back
and strike operator causing se-
vere injury or death.
Figure 14 - Bucking Log With Entire
Length On Ground
Limbingisremovingbranchesfromafallen
tree. Make sure your footing is firm. Keep
feet apart. Divide your weight evenly on
both feet. Do not remove larger limbs under
tree that support log off ground. Remove
each limb with one cut (see Figure 13).
Clear cut limbs from work area often. This
will help maintain a safe work area.
Log Supported On One End
1. Make first cut on underside of log (see
Figure 15). Use top of guide bar to
make this cut. Cut 1/3 through diam-
eter of log. This cut will keep section
from splintering when cut.
Bucking a log is cutting a log into sections.
Make sure your footing is firm. Keep feet
apart. Divide your weight evenly on both feet.
Whenpossible,raiselogorsectionoffground.
Do this by using limbs, logs, chocks, etc.
2. Make second cut directly above first
cut. Cut down to meet first cut. This
cut will keep log from pinching guide
bar and chain.
Make sure you start your cut where limb
will not pinch saw during cutting. To avoid
pinching, start cut on freely hanging limbs
from above limb. Start cut on limbs under
tension from under limb. If pinch occurs,
turn saw off, lift limb, and remove saw.
When cutting through log, maintain control
byreducingcuttingpressurenearendofcut.
Donotrelaxyourgriponchainsawhandles.
Do not let moving chain touch ground.
Ground will dull moving chain. After cut-
ting through log, release trigger to turn saw
off before moving saw.
2nd Cut
Follow directions below to buck a log.
1st Cut
Figure 15 - Bucking Log When Log Is
Supported On One End
Figure 13 - Limbing A Tree
097017
10
OWNER’S MANUAL
2nd Cut -
Pruning Cut
(to avoid pinching)
TRIMMING A TREE (Pruning)
OPERATING CHAIN
4th Cut -
Final Stub
Cut
SAW
WARNING: Avoid kickback.
Kickback can result in severe in-
juryordeath.SeeKickback,page
3 to avoid risk of kickback.
Continued
Log Supported On Both Ends
1. Make first cut from above log (see Fig-
ure 16). Cut 1/3 through diameter of
log. This cut will keep section from
splintering when cut.
6"
WARNING: Do not operate
chain saw while
• in a tree
• on a ladder or any other un-
stable surface
• in any awkward position
Youmaylosecontrolofsawcaus-
ing severe injury.
2" to 4"
2. Make second cut on underside of log,
directly under first cut. Use top of guide
bar to make this cut. Cut up to meet
first cut. This will keep log from pinch-
ing guide bar and chain.
1st Cut -
Pruning Undercut
(to avoid splintering)
3rd Cut - Stub Undercut
(to avoid splintering)
WARNING: Do not cut limbs
higher than your shoulders.
1st Cut
Figure 17 - Cutting A Limb
CAUTION: Seek professional
help if facing conditions beyond
your ability.
Trimming a tree is the process of cutting
limbs from a living tree. Make sure your
footing is firm. Keep feet apart. Divide your
weight evenly on both feet. Follow direc-
tions below to trim a tree.
1. Make first cut six inches from tree trunk
on underside of limb. Use top of guide
bar to make this cut. Cut 1/3 through
diameter of limb (see Figure 17).
2nd Cut
Figure 16 - Bucking Log When Log Is
Supported On Both Ends
2. Move two to four inches farther out on
limb. Make second cut from above limb.
Continue cut until you cut limb off.
3. Make third cut as close to tree trunk as
possible on underside of limb stub. Use
top of guide bar to make this cut. Cut
1/3 through diameter of stub.
4. Make fourth cut directly above third
cut. Cut down to meet third cut. This
will remove limb stub.
097017
11
®
ELECTRIC CHAIN SAW
Normal Guide Bar Maintenance
1. Remove guide bar from chain saw.
CARE OF GUIDE BAR
CLEANING AND
MAINTENANCE
Uneven bar wear causes most guide bar
problems. Incorrect sharpening of chain
cutter and depth gauge settings often cause
this. When bar wears unevenly, it widens
guidebargroove(seeFigure18).Thiscauses
chainclatterandrivetpopping. Sawwillnot
cutstraight.Replaceguidebarifthisoccurs.
2. Remove sawdust from guide bar
groove periodically. Use putty knife or
wire.
NOTICE: Below are instructions
forservicingyourchainsaw.Any
servicing not mentioned below
should be done by an authorized
service center.
3. Clean oil slots after each day of use.
4. Remove burrs from sides of guide bar.
Use flat file to make side edges square.
Inspect guide bar before sharpening chain.
A worn or damaged guide bar is unsafe. A
worn or damaged guide bar will damage
chain. It will also make cutting harder.
Replace guide bar when
• bar is bent or cracked
CLEANING SAW BODY
• inside groove of bar is badly worn
WARNING: Unplug chain saw
from power source before servic-
ing. Severe injury or death could
occur from electrical shock or
body contact with moving chain.
Note: When replacing guide bar, see Re-
placement Parts and Accessories, on back
cover, for proper bar.
Guide Bar
Groove
Burr
WARNING: Cutting edges on
chain are sharp. Use protective
gloves when handling chain.
Guide Bar
WARNING: When cleaning
saw body,
• do not submerge saw in any
liquids
Flat File
• do not use products that con-
tain ammonia, chlorine, or
abrasives
• do not use chlorinated clean-
ingsolvents,carbontetrachlo-
ride, kerosene, or gasoline
Guide Bar
Guide Bar
With Uneven
Normal Guide
Cleaning Groove With
Putty Knife
Bar
Wear
Figure18-GuideBarCrossSectionShow-
ing Uneven Bar Wear
Keepsawbodyclean.Useasoftclothdamp-
ened with a mild soap and water mixture.
Wipe saw body to clean.
Oil Slot
Figure 19 - Guide Bar Maintenance
097017
12
OWNER’S MANUAL
4. Hold file guide level. Make sure 30°
mark on file guide is parallel to center
of guide bar (see Figure 20). This will
Sharpening Cutters
CLEANING AND
Use file guide for 30° filing.
1. Adjust chain for proper tension (see Saw
MAINTENANCE
insure that you file cutters at 30° angle.
Continued
Chain Tension Adjustment, page 7).
5. File from inside towards outside of cut-
ter until sharp. Only file in this one direc-
tion (see Figure 20). Note: Two or three
strokes with file should sharpen cutter.
2. Clamp guide bar in vise to hold saw
SHARPENING SAW CHAIN
(Non-Fast Sharp Model)
steady. Note: Do not clamp chain.
3. Press 5/32" round file (attached to file
guide) into groove between top plate
and depth gauge on chain. File guide
should rest on both top plate and depth
gauge (see Figures 20 and 21). Note:
File at midpoint of guide bar.
6. After each cutter if sharpened, move
chain forward to sharpen next cutter.
File all cutters on one side of chain.
WARNING: Unplug chain saw
from power source before servic-
ing. Severe injury or death could
occur from electrical shock or
body contact with moving chain.
7. Move to other side of chain and repeat
process.
Filing
Direction
WARNING: Cutting edges on
chain are sharp. Use protective
gloves when handling chain.
30° Guide
Mark
File
Guide
Keep chain sharp. Your saw will cut faster
and more safely. A dull chain will cause
undue sprocket, guide bar, chain, and motor
wear. If you must force chain into wood and
cutting creates only sawdust with few large
chips, chain is dull.
5/32"
Round File
Items Needed to Sharpen Chain
Note: This illustration
Purchasetheseitemsfromyourlocaldealer,
hardwarestore,orchainsawsuppliesoutlet.
shows file guide
placement and filing
direction for sharpen-
ing cutters on left side
of chain.
• 5/32" round file
• Depth gauge tool
• File guide
• Vise
Figure 20 - File and File Guide Placement On Chain
• Medium sized flat file
Groove
Depth Gauge
(left side of chain)
Left Side of
Chain
Depth Gauge
(right side
of chain)
Groove
Top Plate
(right side of chain)
Top Plate
(left side of chain)
Right Side of
Chain
Figure 21 - Chain Part Locations
Continued
097017
13
®
ELECTRIC CHAIN SAW
5. Place saw on clean, flat surface.
6. Connect saw to power supply.
SHARPENING SAW CHAIN
(Fast Sharp Model)
CLEANING AND
MAINTENANCE
7. Hold saw, with both hands in normal
cutting position.
Continued
WARNING: Unplug chain saw
8. Press in switch lockout with right
thumb and squeeze trigger.
from power source before servic-
ing. Severe injury or death could
occur from electrical shock or
body contact with moving chain.
Filing Cutter Depth Gauges
The cutter depth gauge clearance is reduced
as cutters are sharpened. After every second
orthirdsharpening,resetcutterdepthgauges.
9. Gently push on sharpener knob. Saw
must be running for chain to sharpen.
Note: Sparks appearing shows sharp-
ener is working (see Figure 25). If no
sparks appear, continue to adjust sharp-
ener one click at a time. After each
click, press sharpener knob until light
flow of sparks appears.
1. Place depth gauge tool (.025") firmly
across top of two cutters. Make sure
depth gauge enters slot in depth gauge
tool (see Figure 22).
WARNING: Cutting edges on
chain are sharp. Use protective
gloves when handling chain.
2. Use medium flat file. File depth gauge
level with depth gauge tool.
WARNING: Do not hand-
sharpen this Fast Sharp chain.
Hand-sharpening chain will in-
crease risk of kickback.
After several sharpenings, you must turn
sharpener knob more to bring stone into
position.
3. Remove depth gauge tool. With flat file,
round off front corner of cutter depth
gauge (see Figure 23).
After several hand filings, have authorized
servicecenterorsharpeningservicemachine
sharpen chain. This will insure even filing.
Keep chain sharp. Your saw will cut faster
and more safely. A dull chain will cause
undue sprocket, guide bar, chain, and motor
wear. If you must force chain into wood and
cutting creates only sawdust with few large
chips, chain is dull.
Flat File
Depth Gauge
Follow the steps below to sharpen Fast
Sharpchain. Theautomaticchainsharpener
sharpens cutter, lowers cutter depth gauge,
and adjusts guard drive link.
Figure 25 - Sharpening Fast Sharp Chain
Depth
Gauge
Tool
1. Adjust saw chain for proper tension
(see Saw Chain Tension Adjustment,
page 7).
REPLACING SAW CHAIN
Replace chain when cutters are too worn to
sharpen or when chain breaks. Only use
replacement chain noted in this manual.
Always include new drive sprocket when
replacing chain. This will maintain proper
drivingofchain.Note:Forproperchainand
drive sprocket, see Replacement Parts and
Accessories, on back cover.
2. Clean out excess sawdust and wood
chips from drive sprocket area.
Depth
Gauge
Slot
3. Turn sharpener knob counterclockwise
until clicking stops (see Figure 24).
4. Turn sharpener knob clockwise until
you hear five distinct clicks.
Figure 22 - Depth Gauge Tool On Chain
Front Corner
.025"
PUSH
SHARPTEON
Figure 23 - Round Off Front Corner Of
Depth Gauge
Sharpener
Knob
Figure 24 - Turning Sharpener Knob
097017
14
OWNER’S MANUAL
TROUBLESHOOTING
WARNING: Unplug chain saw from power source before servicing.
Severe injury or death could occur from electrical shock or body contact
with moving chain.
OBSERVED FAULT
POSSIBLE CAUSE
REMEDY
Saw runs, but does not cut.
Chain assembled backwards on guide bar
See Assembly, page 6
Saw does not cut unless heavily forced. Chain is dull
Cutting produces only sawdust with few
large chips.
See Sharpening Saw Chain, page 13 (non-
Fast Sharp model) or page 14 (Fast Sharp
model)
Saw runs slow. Saw stalls easily.
Low power supply voltage
Extension cord wire size too small. See
Extension Cords, page 8
Motorofsawdoesnotrunwhenyousqueeze 1. Switch lockout not pressed in to release 1. Press in switch lockout before squeez-
trigger.
trigger
ing trigger
2. Extension cord connections loose
3. Open line fuse or circuit breaker
4. Bad motor brushes
2. Check cord connections
3. Check line fuse or circuit breaker
4. See authorized service center
5. See authorized service center
5. Open wiring circuit on saw
Motorofsawruns, butchaindoesnotmove. Gear train failure
See authorized service center
Chain does not get oil.
1. Clogged oil slot in guide bar
2. Oil is too thick
1. Remove guide bar and clean oil slot
2. Use correct weight of oil. See Filling Oil
Tank, page 7
Chain comes off guide bar.
1. Chain is loose
1. Tighten chain. See Saw Chain Tension
Adjustment, page 7
2. Guide bar and chain not assembled right 2. See Assembly, page 6
Saw smokes.
Saw leaks oil.
Saw damaged. Do not use saw.
Oil cap is not secure.
See authorized service center
Tighten oil cap. Note: Empty oil tank when
not in use.
6. Wipe off outside of saw body. Do this
with soft cloth dampened with a mild
soap and water mixture.
STORAGE
SERVICE
PUBLICATIONS
If storing saw for more than 30 days, follow
steps below.
7. Store chain saw
You can buy a service manual from address
listedonbackpageofthismanual.Sendacheck
for $5.00 payable to DESA International.
• in a high or locked place, out of
children’s reach
• in a dry place
• in a carrying case or with scabbard
over guide bar
1. Drain oil tank.
2. Remove and clean guide bar and chain.
Clean guide bar and chain by soaking
in petroleum based solvent or mild soap
and water mixture.
You can receive an illustrated parts list free
of charge. Send a self-addressed stamped
envelope to address on back page of this
manual.
3. Dry guide bar and chain.
4. Place chain in container filled with oil.
This will prevent rust.
TECHNICAL
SERVICE
When writing, include model number and
serial number of saw. You will find these
numbers on saw motor housing decal.
5. Wipe a thin coating of oil over surface
of guide bar.
You may have further questions about as-
sembling,operating,ormaintainingthissaw.
If so, contact DESA International’s Techni-
cal Service Department at 1-800-323-5190.
097017
15
®
ELECTRIC CHAIN SAW
PARTS CENTRALS
Ray's Portable Heater Service
3191 Myers Road
Camino, CA 95709
Portable Heater Parts
342 North County Road 400 East
Valparaiso, IN 46383
219-462-7441
Four Flags Power Products
1115 Stateline Road
Niles, MI 49120
Forrest Lytle and Sons Inc.
740 West Galbraith Road
Cincinnati, OH 45231
513-521-1464
Webbs Appliance Center
1519 Church Street
Nashville, TN 37203
615-329-4079
616-684-2697
916-644-7716
1-800-362-6951
1-800-268-4983
1-800-899-4079
Bortz Chain Saw Shop
Road #2, Box 64A
Oley, PA 19547
Baltimore Electronics
1348 Dixwell Avenue
Hamden, CT 06514
203-248-7553
FBD
Hance Distributors Inc.
12795 16th Avenue North
Plymouth, MN 55441
612-559-2299
Industrial Hardware
4109 Bainbridge Blvd.
Chesapeake, VA 23324
757-543-2232
1349 Adams Street
Bowling Green, KY 42103-3414
502-846-1199
610-987-6452
1-800-397-7553
21st Century
1-800-788-0008
1-800-654-8534
Automotive Equipment Service
3117 Holmes
Kansas City, MO 64109
816-531-9144
2950 Fretz Valley Road
Perkasie, PA 18944
215-795-0400
Eckley’s Small Engine
31617 Spruce Drive
Eustis, FL 32726
Mills Lawn and Garden
4750 B. Baxter Road, Unit B
Virginia Beach, VA 23462
757-490-7001
Lyons & Lyons Sales Co. Inc.
Glen Arm Road
Glen Arm, MD 21057
301-665-6500
352-357-6764
1-800-325-4828
1-800-843-3546
Parts Company of America
1657 Shermer Road
Northbrook, Ill 60062
708-498-5900
LaPortes' Parts & Service
2444 N 5th Street
Hartsville, SC 29550
1-800-333-5966
Sun Appliance Service Center
1687 Central Avenue
Albany, NY 12205
Tuco Industrial Products
5223 180th Street SW
Suite 4A-1
Lynnwood, WA 98037
425-743-9533
Master Parts Distributors
1184 Wilson NW
Grand Rapids, MI 49544
1-616-791-0505
1-800-446-1446
803-332-0191
518-869-9591
1-800-323-0620
1-800-735-1268
AUTHORIZED SERVICE CENTERS
ALABAMA (AL)
California Electric Service
1139 East 12th Street
Oakland, CA 94606
510-834-1050
COLORADO (CO)
FLORIDA (FL)
IDAHO (ID)
A & O General Repair Service
1470 Opelika Road
Auburn, AL 36830
334-821-7022
McGuckin Power Equipment Center
2845 Valmont Road
Boulder, CO 80302
303-443-9317
Cricket Shop
Rossiter Electric
1501 S. Capitol Ave.
Idaho Falls, ID 83403
208-529-3665
3012 39th Avenue West
Bradenton, FL 34205
941-755-7758
California Electric Service
2594 East Colorado Blvd.
Pasadena, CA 91107
818-792-3194
Southern Power Tool
3956 Government Blvd.
Mobile, AL 36693
334-666-3623
Ace Mower and Small Engines
4718 Chromium Drive
Colorado Spring, CO 80918
719-593-0862
Eckley's Small Engine
31617 Spruce Drive
Eustis, FL 32736
352-357-6764
Steam Store Rocky Mountain, Inc.
155 North Gate Mile
Idaho Falls, ID 83401
208-522-0609
California Electric Service
1717 Bell Street
Sacramento, CA 95814
916-443-5711
ARIZONA (AZ)
Bartell Tool Service
1448 W. Cedar Avenue
Denver, CO 80223
303-777-5463
Al's Small Engine, Inc.
2620 Blanding Blvd.
Middleburg, FL 32068
904-282-5416
Steam Store of Magic Valley, Inc.
156 4th Avenue South
Twin Falls, ID 83301
208-734-3694
Best Brothers Lawnmower Repair
5549 W. Glendale Avenue
Glendale, AZ 85301
602-939-9170
California Electric Service
3430 El Cajon Blvd.
San Diego, CA 92104
619-283-6488
Metrogas Equipment Company
790 West 64th Ave.
Denver, CO 80221
303-428-3036
S TEK Power Tools
2605 South Orange Avenue
Orlando, FL 32806
407-851-5642
J & J Enterprises
D & L Small Engines, Inc.
10023 North 19th Ave.
Phoenix, AZ 85021
602-861-1978
1704 Addison Avenue East
Twin Falls, ID 83301
208-733-2001
California Electric Service
1090 Bryant Street
San Francisco, CA 94103
415-431-8494
Winfrey's Repair
317 8th Street
Greeley, CO 80631
970-353-9576
Lindle & Sons Electric Motor Repair
7016 Hwy. 22
Panama City, FL 32401
850-871-1722
ILLINOIS (IL)
Power Tool Service Center
660 East 19th Street
Tucson, AZ 85719
520-884-8974
Cherry Valley Small Engine Repair
702 East State Street
Cherry Valley, IL 61016
815-332-5636
California Electric Service
783 The Alamada
San Jose, CA 95126
408-295-0475
AAA Electric Company, Inc.
24 South Main Street
Longmont, CO 80501
330-776-6031
Eustis and Sons, Inc.
7035 66th Street North
Pinellas Park, FL 34665
813-544-1486
CALIFORNIA (CA)
Ray's Portable Heater Service
3191 Meyers Road
Camino, CA 95709
916-644-7716
Chainsaw Central
11 E. Main Street
Chicago Heights, IL 60411
708-756-2280
Lawnmower & Saw
3115 S. Main Street
Santa Ana, CA 92707
714-540-5307
Dales Electric Motor Repair
932 Coffman Street
Longmont, CO 80501
303-651-6907
Mulvaney's Inc.
2148 W. Tennessee Street
Tallahassee, FL 32304
904-576-5578
Lange Electric
California Electric Service
1170 G. Burnett Avenue
Concord, CA 94520
510-827-1011
912 E. Fayette
Effingham, IL 62401
217-347-7626
Rincon Valley Yard & Garden
4972 Sonoma Hwy
Santa Rosa, CA 95409
707-593-4124
CONNECTICUT (CT)
Baltimore Electronics
1348 Dixwell Avenue
Hamden, CT 06514
203-248-7553
A-1 Tool Rental, Inc.
2509 South State Road 7
West Hollywood, FL 33023
305-961-9250
H & R Pump Company, Inc.
2111 E. Washington Street
Joliet, IL 60434
California Electric Service
612 South Shoppers Lane
Covina, CA 91723
California Electric Service
41715 Enterprise Circle North
Suite 101
Temecula, CA 92590
909-695-5445
815-726-2950
818-915-4935
1-800-397-7553
GEORGIA (GA)
Hamilton Hardware
5300 Veterans Pkwy.
Columbus, GA 31904
706-322-6545
Mathis-Kelley Construction
1046 W. Jefferson Street
Morton, IL 61550
California Electric Company
1208 East Ash Avenue
Fullerton, CA 92631
714-870-0900
Utility Electric Service
53 Main Street
Hartford, CT 06106
860-246-7271
309-266-9733
California Electric Service
14753 Oxnard Street
Van Nuys, CA 91411
818-997-8855
Cowan Ace Hardware
1264 Green Street
Conyers, GA 30207
770-483-8818
Ambraw Power Equipment
310 E. Decatur Street
Newton, IL 62448
J & N Garden Equipment
4460 W. Imperial Hwy.
Inglewood, CA 90304
310-671-0079
Goodies Sales and Service
133 Hamilton Street
New Haven, CT 06515
203-865-1470
618-783-2821
California Electric Service
2314 South Westwood Blvd.
W. Los Angeles, CA 90064
310-475-2532
Douglasville Ace Hardware
6530 Church Street
Douglasville, GA 30133
770-942-7044
California Electric Company
11284 Los Alamitos Blvd.
Los Alamitos, CA 90720
310-596-7895
Appliance Servicenter of Stamford
15 Cedar Heights Road
Stamford, CT 06905
PBI
203-322-7656
3160 Industrial Drive
Yuba City, CA 95993
916-671-1871
S & P Rental & Supply Co.
259 Clayton Street
Lawrenceville, GA 30245
770-963-0392
California Electric Service
23725 Via Fabricante, Unit B
Mission Viejo, CA 92691
714-586-9440
Tifton Electric Motors
1265 US Hwy. 82E
Tifton, GA 31794
912-382-4040
097017
16
OWNER’S MANUAL
INDIANA (IN)
KANSAS (KS)
MARYLAND (MD)
Fowler's Farm City Sales
2876 West Washington Road
Ithaca, MI 48847
MONTANA (MT)
Hutchens Sales and Service
R.R. #5, Box 550
Bloomfield, IN 47424
812-876-1891
Abilene Rent-All & Sales
1701 West 1st Street
Abilene, KS 67410
913-263-7668
Center Supply Company
6802 Industrial Drive #208
Beltsville, MD 20705
301-595-0860
Tom's Service Repair
1111-6th Avenue North
Billings, MT 59103
406-259-6179
517-875-3976
Superior Industrial Sales & Service
116 N. State Street
Jackson, MI 49201
517-784-0539
Nichols Ice & Oil
2018 Park Road
Connersville, IN 47331
317-825-3741
NAAB Electric, Inc.
2013 W. Jones
Garden City, KS 67846
316-276-8101
Lehmans Hardware, Inc.
5921 Belair Road
Baltimore, MD 21206
410-483-5888
Mosch Electric Motors, Inc.
2513 - 17th St. NE
Black Eagle, MT 59414
406-453-2481
Norm's Electric Motor Repair
414 Walbridge
Kalamazoo, MI 49001
616-382-5054
B & W Repair Service
213 N. Main Street
Dale, IN 47523
Morris Electric Repair
2423 5th Street
Great Bend, KS 67530
316-792-2919
Norris Taylor Contractors, Inc.
8480 Ocean Gateway
Easton, MD 21601
Sun Rental Center
1301 - 3rd St. NW
Great Falls, MT 59404
406-761-6688
812-937-2576
410-822-2050
A & J Rentals
Reggie's Small Engine Spec.
3011 Lower Huntington Road
Ft. Wayne, IN 46809
McPherson Rental Center
911 West First Street
McPherson, KS 67460
316-241-3333
Southern States Frederick Coop
500 E. South Street
550 S. 11th Street
Niles, MI 49120
616-684-3200
NEBRASKA (NE)
Hatten's Electric Service
130 S. Hastings, Box 843
Hastings, NE 68901
402-463-4596
Frederick, MD 21705
301-663-6165
219-747-6212
Four Flags Power Products
1115 Stateline Road
Niles, MI 49120
Eastside Electric
928 East Lincoln
Goshen, IN 46526
219-533-3823
Town and Country
2008 Princeton
Ottawa, KS 66067
913-242-3133
Lyons and Lyons Sales Co., Inc.
Glen Arm Road
Lincoln Tool Service Center
3535 North 40th Street
Lincoln, NE 68404
402-464-1157
Glen Arm, MD 21057
410-665-6500
616-684-2697
Bob's Service Shop
2537 W. Drahner Road
Oxford, MI 48371
810-628-2601
Mills Electric
KENTUCKY (KY)
Hart's Motor Service
1747 Woodlawn Road
Bardstown, KY 40004
502-348-3270
Chesapeake Rent All
210 N. Stokes Street
Havre De Grace, MD 21078
410-939-1720
4828 Calumet Ave.
Hammond, IN 46327
219-931-3114
Flohr Electric Motor
4356 South 90th Street
Omaha, NE 68127
402-331-6863
Don's Small Engine Repair
630 S. Mill Street
Plymouth, MI 48170
313-451-5656
Tyrie Mower Repair
110 South 16th Street
Lafayette, IN 47905
317-742-7886
Tracy's Appliance Company
520 Soleman's Island Road
P. Frederick, MD 20678
301-855-1818
E-Z Rent It Inc.
MSE Parts Unlimited
4935 South 136th Street
Omaha, NE 68137
402-895-0806
1428 U.S. 31-W By-Pass
Bowling Green, KY 42101
502-782-9462
Bid's Service, Inc.
11276 E. Ten Mile
Warren, MI 48089
810-759-3040
Kabelin True Value Hardware
512 Andrew Avenue
Laporte, IN 46350
MASSACHUSETTS (MA)
Holander Electric, Inc.
36 Walton Street
Attleboro, MA 02703
508-226-1060
Roman's Repair Shop
601 College Street
Bowling Green, KY 42101
502-746-0857
Ted's Mower Sales and Service, Inc.
5155 Q. Street
Omaha, NE 68117
402-731-7058
219-362-7917
MINNESOTA (MN)
Patrick's Sales & Service
415 - 8th Ave. NE
Brainerd, MN 56401
218-829-5356
Krep's Small Engine Repair
3301 East County Road 350 North
Muncie, IN 47303
Hopkinsville Electric Motor
704 W. 15th Street
Hopkinsville, KY 42240
502-886-7585
Ormond's Inc.
LaVern Hass Repair
1204 - 1st Road
Wisner, NE 68791
402-529-6846
115R Dean Ave.
Franklin, MA 02038
508-528-2013
317-282-5139
Lear Lawn & Garden
2204 N. Wolfe Street
Muncie, IN 47303
317-282-6273
Perry's Electrical Rebuilders
24630 Hale Avenue
Forest Lake, MN 55025
612-464-8054
Maury's Fluorescent Appliance
1521 Bardstown Road
Louisville, KY 40205
502-456-1671
Beacon Lumber/Beacon Rental
513 Church Street
NEVADA (NV)
Fallon Saw & Tool
300 N. Marine St.
Fallon, NV 89406
702-423-1888
New Bedford, MA 02745
508-995-1766
Li'l Engine Sales & Service, Inc.
1428 Vincennes Street
New Albany, IN 47150
812-944-1377
Hance Distributor, Inc.
12795 16th Avenue North
Plymouth, MN 55441
612-559-2299
Rental World, Inc.
9509 Dixie Hwy.
Louisville, KY 40272
502-935-8853
Grafton Power Equipment
North Grafton Shopping Center
9 Williams Road
North Grafton, MA 01536
508-839-6366
One Stop Shop
1408 Industrial Way #3
Gardnerville, NV 89410
702-782-7004
Ertel & Sons Portable Welding
109 E. Main Street
Swayzee, IN 46986
317-922-4611
Hance Sales and Service
11212 Wayzata Blvd.
Minnetonka, MN 52343
612-545-8467
All States Industrial Repair
728 E. Center Street
Madisonville, KY 42431
502-821-6555
Mott's Tool Repair Service
92 Rayber Road
Orleans, MA 02653
508-240-0764
NEW HAMPSHIRE (NH)
Taylor Rental Center
223 Wincherster Street
Keene, NH 03431
603-352-0539
Portable Heater Parts
342 North County Road, 400 East
Valparaiso, IN 46383
219-462-7441
Andy's Small Engine Repair
209 9th Avenue, NE
Rochester, MN 55906
507-280-0373
Bluegrass Plumbing and Heating
121 South First Street
Richmond, KY 40475
606-623-2390
Utility Electric Service #2
810 Main Street
Springfield, MA 01105
413-781-1635
Kingston Enterprises
85 North Road
Kingston, NH 03848
603-642-3506
D W Handy's
Reed's Sales & Service
1260 Payne Ave.
St. Paul, MN 55101
612-774-9515
2112 S. 15th Street
Vincennes, IN 47591
812-886-0172
LOUISIANA (LA)
Welch Sales & Service
13348 W. Main
La Rose, LA 70373
504-693-3351
Franconia Fuel Company, Inc.
379 Main Street
Wareham, MA 02571
508-295-0039
Hammar Industrial Supply
175 Amherst Street
Nashua, NH 03061
603-822-5161
IOWA (IA)
Brown's
408 South Fifth Street
Abel, IA 50003
515-993-3053
MISSISSIPPI (MS)
Handy Man Rentals
1904 Shiloh Road
Corinth, MS 38834
601-287-2460
Triangle Bicycle and Lawnmower
5433 Crowder Road
New Orleans, LA 70127
504-241-3239
MICHIGAN (MI)
R & A Service
12900 Haggerty Road
Belleville, MI 48111
313-697-1144
Exeter Rent All
State Rt 27, Box 68A
Raymond, NH 03077
603-895-6583
Beal's Motor Rewinding
600 West Beach
Cherokee, IA 51012
712-225-6173
MISSOURI (MO)
MAINE (ME)
Stewarts Enterprises
7631 NW Salebarn Road
Cameron, MO 64429
816-632-6578
Richard's Electric Motor
259 Main Street
Caribou, ME 04736
207-498-8950
Thompson's Rental Resale Repair
11973 New Lothrop Road
Byron, MI 48418
Blink Electric Motors
Rear 116 N. 1st Ave.
Marshalltown, IA 50158
515-752-3036
810-266-4969
Northwest Power Sales
RD #2, Box 200
Maryville, MO 64468
816-582-5080
Roger's Electric Motor Shop
823-West Main Street
Madawaska, ME 04756
207-728-4253
Renter Center, Inc.
24948 Gratiot
East Pointe, MI 48021
810-772-8111
Fry Company
Box 96 Thatcher Ave.
Millerton, IA 50165
515-897-3235
Buchheit, Inc.
Rent-N-Save
Master Service Center
7876 Division
Grand Rapids, MI 49504
616-455-3117
Route 7, Box 239
Perryville, MO 63775
573-547-1010
28 Allen Avenue
Portland, ME 04103
207-797-2223
Moreland Repair
2145 Jericho Road
Peosta, IA 52068
319-583-3669
L.A. Pickard Sales & Service
383 Lewiston Road
Topsham, ME 04086
207-725-2874
Wolf Creek Farm Supply
8011 Wolf Creek Road
Herron, MI 49744
Northeast Iowa Motor Service
24665-150th Street
Sumner, IA 50674
517-727-2391
Chicago Drive Rentals, Inc.
11298 Chicago Drive
Holland, MI 49424
616-396-9575
319-578-5883
Black Hawk Rental
324 West 15th Street
Waterloo, IA 50702
319-234-4421
097017
17
®
ELECTRIC CHAIN SAW
NEW JERSEY (NJ)
Complete Saw Service
336 River Road
Advanced Power Equipment
101 Fairgrounds Drive
Manlius, NY 13104
315-682-4010
North East Mower Service
412 East 156th Street
Cleveland, OH 44110
216-531-8197
OREGON (OR)
SOUTH CAROLINA (SC)
Hall's Small Motor Repair
225 Heathwood Drive
Aiken, SC 29803
Turner’s Lawnmower and Saw
728 SE Robin Way
Gresham, OR 97080
503-665-5441
Garfield, NJ 07026
201-478-7838
803-649-6313
P & C
Pecnik's Lawnmower Service
732 East 163rd Street
Cleveland, OH 44110
216-531-8480
Nemeth's Mower Service
55 - 4th Ave.
Haskell, NJ 07420
201-835-0080
12 East Street
Nunda, NY 14517
716-468-5050
Pendleton Grain Growers
200 S. 1st Street
P.O. Box 1248
Hermiston, OR 97801
541-567-5591
Todd's Electric Motor Repair
110 Laurel Street
Conway, SC 29526
803-248-2444
Otega Repair
Lefeld Welding & Steel Supply
512 N. Second Street
Coldwater, OH 45828
419-678-2397
Air & Electric Tool Service, Inc.
215 North 8th Street
Kenilworth, NJ 07033
908-272-5567
Rd #2, Ostdawa Ave.
Otego, NY 13825
607-988-7859
LaPortes Parts & Service
2444 N. 5th Street
Hartsville, SC 29550
803-332-0191
Mattix Appliance Parts Company
501 N. Main
Phoenix, OR 97535
541-535-6263
Owego Agway Coop
38 West Avenue
Owego, NY 13827
607-687-2039
Dayton Hardware & Supply
16-32 N. Irwin Street
Dayton, OH 45404
Associated Industries
Rd 38, Box 2486
Mt. Holley, NJ 08060
609-267-8417
Turner Repair Service
3 E. Belvue Road
Taylors, SC 29687
864-244-1746
Oregon Appliance
2137 East Burnside Street
Portland, OR 97214
503-235-6681
513-258-3721
1-800-762-3426 Ohio only
Jack-n-Heater Service
185 Beartown Road
Painted Post, NY 14870
607-962-1239
Woodchuck's Lawnmower
and Appliance
220 Whitehorse Pike
Magnolia, NJ 08049
609-783-1111
Ken's Repair
TENNESSEE (TN)
3246 S. Sectionline
Delaware, OH 43015
614-369-4798
PENNSYLVANIA (PA)
Albright's Hardware
2119 Wabert Ave.
Allentown, PA 18104
610-433-3831
Cole's Small Equipment Center
247-A Vance Tank Road
Bristol, TN 37620
Larmon Small Engine
16353 Co. Rt. 91
Pierrepont Manor, NY 13674
315-465-6671
615-968-1175
Lavon Dietsch Repair
07145 Scott Rd. Rt #2
Edgerton, OH 43517
419-298-2948
Myron Tepper/Tep's Power
Equipment
1007 N. High Street
Millville, NJ 08332
609-825-8294
Vista Small Engine
1510 Vista Lane
Clarksville, TN 37043
615-552-6953
General Rental & Sales Center
Old Rt 1 & 41
Avondale, PA 19311
610-268-2825
R & D Mower & Snowblower
Sales and Service
1630 Empire Blvd.
Webster, NY 14580
716-671-9409
Anytool & Outdoor Power Equip.
21150 Lorain Road
Fairview Park, OH 44126
216-356-1920
Master Repair Service
305 Elmore Road
Crossville, TN 38555
615-484-2061
Capitol Service & Equipment
551 New Market Road
Piscataway, NJ 08855
908-968-5577
Bud's Tractor and Mower Sevice
21 Bock Lane
Baden, PA 15005
412-869-7142
Bedford Appliance, Inc.
1173 Yonkers Ave.
Yonkers, NY 10704
914-237-7575
LaGrange True Value
300 E. Main Street
LaGrange, OH 44050
216-355-4222
The Speciality Shop
2300 East Magnolia Avenue
Knoxville, TN 37917
423-523-6894
Handyman's Tool Shop
508 State Hwy. #10
Randolph, NJ 07869
201-361-1581
Copper Creek
Rd. #1, Locust Valley
Barnesville, PA 18214
717-467-2792
NORTH CAROLINA (NC)
Ray's Lawn Mower & Machine
1414 Landis Avenue
Charlotte, NC 28205
704-377-1112
Deep Run Mower Service
58781 Heil Addn. Deep Run
Martins Ferry, OH 43935
614-859-6131
Authorized Equipment Service
812 Polk Avenue
Memphis, TN 38126
901-774-0850
Sam's Repair Shop
137 W. Bennett Ave.
Wildwood, NJ 03077
603-895-6583
Passmore Service Center
1108 Rt. 100
Betchelsville, PA 19505
610-367-9084
Worcester Sales and Service
34200 Lorian Road
N. Ridgeville, OH 44039
216-327-2196
Martin Equipment Company
4209-B US 70 E.
Goldsboro, NC 27534
919-778-5996
Webb's Appliance Service Center
1519 Church Street
Nashville, TN 37203
615-329-4079
NEW MEXICO (NM)
K & S Service Center
7521 Menaul N.E.
Albuquerque, NM 87110
505-884-6262
Engine Doctors
20 Russell Blvd.
Bradford, PA 16701
814-362-3091
Staker Sales & Service
1424 Ninth Street
Portsmouth, OH 45662
614-353-6965
Hickory Home & Garden Center
336 HWY 321 NW
Hickory, NC 28601
704-327-3719
TEXAS (TX)
Pro-Fix
Industrial Distributing Co.
9411 Neils Thompson Dr.
Austin, TX 78759
512-837-4122
NEW YORK (NY)
Rear 681 Main Street
Edwardsville, PA 18704
717-288-0476
Sun Appliance Service Center
1687 Central Avenue
Albany, NY 12205
518-869-9591
Leonard Hardware
145 North 15th Street
Sebring, OH 44672
330-938-6329
Bowden Electric Motor Service
1681 S. Wesleyan Blvd.
Rocky Mount, NC 27803
919-446-4203
Carson's Hardware
637-43 Main Street
Hellertown, PA 18055
610-838-7741
Bud's LP Gas & Supply
225 Grand
Channelview, TX 77330
713-457-2456
Valley Mower Service
2857 Ellis Creek Road
Barton, NY 13734
607-589-4825
Sparks Sales & Service
5184 Fletcher Chapel Road
Springfield, OH 45502
513-323-5925
Small Engine Performance Ctr.
312 Eldred
Valdese, NC 28690
704-879-9652
Eaton Enterprises
240 Main Street
Imperial, PA 15126
412-695-0702
Corpus Christi Power Tool & Rpr.
3701 Agnes
Corpus Christi, TX 78405
512-883-1117
White Tool Supply Inc.
3047 Atlantic Avenue
Brooklyn, NY 11208
718-227-8844
Eckert Bros.
NORTH DAKOTA (ND)
Fix-It Shop
316 - 21st St. East
Dickinson, ND 58601
701-225-0766
244 Factory Street
Sugarcreek, OH 44681
216-852-2611
Valray Nurseries Inc.
R.D. #8, Box 362
Kittanning, PA 16201
412-548-1579
Freel Enterprise
118 Elston
Dallas, TX 75232
214-376-9913
Shields Brothers of Buffalo
1410 Main Street
Buffalo, NY 14209
716-883-3860
Larry's Mini Engines
4732 US Route 20 West
Wakeman, OH 44889
216-839-2508
Ted's Saw Service
412 South 4th Street
Grand Forks, ND 58201
701-775-7343
Petrosky's Hardware & Supply Co.
602 Alexandria Street
Latrobe, PA 15650
Hawn Equipment Rental
7777 Hawn Freeway
Dallas, TX 75217
214-398-8121
Lehman's Farm & Home Supply
Route 26
Denmark, NY 13631
315-493-1151
OKLAHOMA (OK)
B.M.I. Inc.
13102 East 1st Street
Broken Arrow, OK 74012
918-252-0011
412-537-3541
Craig's Small Engine Repair
508 East 2nd Street
Williston, ND 58801
701-774-0798
Reddi-Rentals
Dyer Cycle
948 S. Woodbourne Rd.
Levittown, PA 19057
215-943-4800
4501 Dyer Street
El Paso, TX 79930
915-566-6022
John’s Engine Repair
10482 Sisson Hwy.
Eden, NY 14057
716-337-3719
H. L. Moss
OHIO (OH)
1714 E. 15th Street
Tulsa, OK 74104
918-744-1305
Raymond, M. Nolt
290 S. Shirk Road
New Holland, PA 17557
717-354-0198
Ray DeSpain's Inc.
Carter Electrical Repair
3448 Lunar Rd. NE
Carrollton, OH 44615
330-627-4061
P.O. Box 184, Loop 494 North
New Caney, TX 77357
713-689-2121
M & S Repair Shop
303 Hilltop Drive
Elma, NY 14059
716-652-0311
Kay Electric Motors Inc.
810 48th Street
Woodward, OK 73801
405-256-3254
Service Department
Bortz Chainsaw Shop
45 Bortz Road
Oley, PA 19547
610-987-6452
Northwest Mower Sales and Service
6086 Cheviot Road
Cincinnati, OH 45247
513-385-2400
Crossbay Appliance Service
158-34 Crossbay Blvd.
Howard Beach, NY 11414
718-843-4422
Snyder Electric Company
1500 Chateau Street
Pittsburgh, PA 15233
412-231-3100
Forrest Lytle & Sons
740 W. Galbraith Road
Cincinnati, OH 45231
513-521-1464
Belco Equipment Company
3801 - 29th Street
Long Island City, NY 11101
718-361-1122
Stamm's Mower Repair
Rd. 5, Pine Lane Box 150
Selinsgrove, PA 17870
717-743-7651
Anytool Precision Sharpening Repair
21150 Lorain Road
Cleveland, OH 44126
216-356-1920
Para-Deys Tools
708 Victor Road
Macedon, NY 14502
315-986-2520
097017
18
OWNER’S MANUAL
UTAH (UT)
VIRGINIA (VA)
WASHINGTON (WA)
Action Small Appliance Service
1500 145th Place SE
Bellevue, WA 98005
206-455-3578
WEST VIRGINIA (WV)
Beckley Mower Service
3695 Robert C. Byrd Drive
Beckley, WV 25802
304-253-5748
Roosevelt Service Center
133 South 300 East, Box 1546
Roosevelt, UT 84066
801-722-2708
Industrial Hardware
4109 Bainbridge Blvd.
Chesapeake, VA 23324
804-543-2232
Longs Engine Service
7536 Stone Road
Salt Lake, UT 84121
801-943-5135
Warren E. Smith Shops
564 Reading Rd. Ext.
300 Madestic Drive
Christiansburg, VA 24073
540-382-5501
TUCO Industrial Products
5227 180th SW, Suite 4A-1
Lynnwood, WA 98046
206-743-9533
Town and Country Supply
4117 First Avenue
Nitro, WV 25143
304-755-3520
Appliance Service Center
210 E. 600 South
Salt Lake City, UT 84111
801-328-9703
Action Small Appliance
2125 Second Avenue
Seattle, WA 98121
206-448-2020
WISCONSIN (WI)
Smith Petroleum Ltd.
217 N. Walworth
Darien, WI 53314
414-724-3206
Mills Repair Service
4750 B. Baxter Road, Unit B
Virginia Beach, VA 23462
757-490-7001
VERMONT (VT)
Brown and Roberts
182 Main Street
Brattleboro, VT 05301
802-257-4566
A to Z Rentals
American Power Equip. Ctr.
6502 Horsepen Road
Richmond, VA 23230
804-285-4838
10903 E. Sprague
Spokane, WA 99206
509-924-2000
Ken's Economy Sales
8887 Highway A
Marshfield, WI 54449
715-676-2143
Lifficks Electric Shop
8239 S. Park Avenue
Tacoma, WA 98408
206-474-7403
Stafford Equipment Sales & Service
21055 Jefferson Davis Hwy.
Stafford, VA 22554
Moore's Repair Service
W287 & N2108 Stuart Drive
Pewaukee, WI 53072
414-691-2814
540-720-1710
Outdoor Power Equipment
800 White Marsh Road
Suffolk, VA 23434
804-925-4933
Morisse Power Center
200 N. Chicago Avenue
S. Milwaukee, WI 53172
414-762-6444
Purchase these accessories and parts from
your nearest dealer or service center. If they
can not supply these accessories or parts,
either contact your nearest Parts Central or
DESA International for referral informa-
tion. Parts centrals are listed in this manual.
REPLACEMENT
PARTS AND
ACCESSORIES
WARNING: Use only replace-
ment parts and accessories de-
scribed in this manual. Use of
other parts or accessories could
damage saw or injure operator.
DESA International
P.O. Box 90004
Bowling Green, KY 42102-9004
1-800-972-7879
Parts Department
LNT-2
Part Number Description
EL-1/EL-7 Fast Sharp
Part Number Description
EL-7 - 100015
Part Number Description
097566-01S
Guide bar, 8"
091369S
097567-01S
091371S
Chain, 8"
Guide bar, 10"
Chain, 10"
097570-01S
091367S*
076695
Guide bar, 14"
Chain, 14"
Drive sprocket
101623-01
101619-01
075752
Guide bar, 15"
Chain, 15"
Drive sprocket
097568-02S
Guide bar, 12"
091373S
Chain, 12"
EL-7, 098031J, 099039J, 100089-01, General
075752
Drive sprocket
100089-04, 100089-05
Part Number Description
Part Number Description
079963-02
Plasticscabbard,8"&10"
099178H, 100089-06, 100089-07 & 097572-03S
Guide bar, 16"
Chain, 16"
Drive sprocket
079963-04
Plastic scabbard,
12", 14", & 16"
Hand Guard
EL-1
091375S
075752
Part Number Description
079088-01
077155
097570-01S
091374S
075752
Guide bar, 14"
Chain, 14"
Drive sprocket
Adjusting Plate Assy.
POLE SAW, 104316-01
POLE SAW ASSEMBLY, 104317
Part Number Description
* Includes automatic chain sharpener.
104302-01S
104301S
075752
Guidebar, 8"
Chain, 8"
Drive Sprocket
097017
19
Warranty Service
Non-Warranty Service
REPAIR SERVICE
If saw requires warranty service, return it to If saw requires service, return it to nearest
nearest authorized service center. You must authorized service center. Repairs will be
show proof of purchase. If faulty materials billed to you at regular repair list prices.
or workmanship caused damage, we will Note:Normalwear, misuse, abuse, neglect,
Note: Only use original replacement parts.
Thiswillprotectyourwarrantycoveragefor
parts replaced under warranty.
Each authorized service center is indepen-
dently owned and operated. For additional
service center or warranty information, call
1-800-323-5190.
repair or replace saw without charge.
or accidental damage is not covered under
warranty.
Model ______________
Serial No. ______________
Date Purchased ______________
ELECTRIC CHAIN SAW LIMITED WARRANTY
Always specify model and serial numbers when writing the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We
make no other warranty, expressed or implied.
DESA International warrants this electric chain saw and any parts thereof, to be free from defects in material and workmanship for one year from
the date of first purchase from an authorized dealer, provided that the product has been properly maintained and operated in accordance with all
applicable instructions. The bill of sales or proof of purchase must be presented at the time a claim is made under this warranty.
This warranty is extended only to the original retail purchaser. This warranty covers only the parts and labor required to restore this chain saw
to its proper operating condition. Warranty parts must be obtained through factory authorized dealers and service centers for this product. These
dealers and service centers will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty.
This warranty does not cover commercial, industrial, or rental usage, nor does it apply to parts that are not in original condition because of normal
wear and tear, or parts that fail or become damaged as a result of misuse, accident, lack of proper maintenance, tampering, or alteration. Travel,
handling, transportation, and incidental costs associated with warranty repairs are not reimbursable under this warranty and are the responsibility
of the owner.
To the full extent allowed by the law of the jurisdiction that governs the sale of the product, this express warranty excludes any and all other
expressed warranties and limits the duration of any and all implied warranties, including warranties of merchantability and fitness for a particular
purpose to one year form the date of first purchase, and DESA International’s liability is hereby limited to the purchase price of the product and
DESA International shall not be liable for any other damages whatsoever including indirect, incidental, or consequential damages.
Some states do not allow limitation of how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages,
so the above limitation of damages may not apply to you.
Thiswarrantyprovidestheoriginalpurchaserwithspecificrights. Forinformationregardingthoserights, pleaseconsulttheapplicablestatelaws.
INTERNATIONAL
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
097017 01
097017-01
REV. X
5/98
NOT A UPC
|