Raritan Computer Calculator PMG 0I v203 E User Manual
Paragon Manager™  
User Guide  
Release 2.0.3  
Copyright © 2009 Raritan, Inc.  
PMG-0I-v2.0.3-E  
May 2009  
255-30-6100-00  
This document contains proprietary information that is protected by copyright. All rights reserved.  
No part of this document may be photocopied, reproduced, or translated into another language  
without express prior written consent of Raritan, Inc.  
© Copyright 2009 Raritan, Inc., Paragon®, Paragon Manager, CommandCenter®, Dominion®,  
and the Raritan company logo are trademarks or registered trademarks of Raritan, Inc. All rights  
reserved. Java® is a registered trademark of Sun Microsystems, Inc. Internet Explorer® is a  
registered trademark of Microsoft Corporation. Netscape® and Netscape Navigator® are  
registered trademarks of Netscape Communication Corporation. All other trademarks or  
registered trademarks are the property of their respective holders.  
System Requirements  
Your system must meet these minimum requirements in order to run Paragon Manager:  
•
•
•
Memory: 256MB  
CPU: 750 MHz Pentium III processor  
Minimum available disk space: 100 MB  
CONTENTS  
i
Contents  
Chapter 1: Introduction .................................................................. 1  
Paragon Manager Overview ......................................................................................................1  
Installing Paragon Manager.......................................................................................................1  
Chapter 2: Operation ...................................................................... 3  
Connection and Login ................................................................................................................3  
Establishing a Connection...................................................................................................3  
Paragon Manager Window Components...................................................................................5  
Toolbar.................................................................................................................................7  
Device Panel..............................................................................................................................8  
Device View.........................................................................................................................9  
Ghosting ............................................................................................................................11  
System Setting.........................................................................................................................12  
User Panel ...............................................................................................................................14  
Creating a User .................................................................................................................14  
Deleting a User..................................................................................................................16  
Viewing User Properties....................................................................................................16  
Saving User Profiles..........................................................................................................17  
Loading a User Profile.......................................................................................................18  
Log Panel.................................................................................................................................19  
Editing Event Log Settings ................................................................................................19  
Power Strip View Panel............................................................................................................20  
Editing Power Strip Data ...................................................................................................20  
Power Strip Outlet Associations........................................................................................21  
Channel Information Editor................................................................................................21  
Multi Function View (MFV) Panel......................................................................................23  
Setting Up Multiple Video Function..........................................................................................24  
Adding an Association Group............................................................................................24  
Editing an Association Group ............................................................................................25  
Deleting an Association Group..........................................................................................25  
Video Redirection (Forced Video)............................................................................................26  
Refreshing IBM Blade Channel Status ....................................................................................26  
Setting Up NV5128 Router Association...................................................................................27  
Overview of the Router Menu............................................................................................27  
Configure Routers .............................................................................................................27  
Configure Servers..............................................................................................................29  
Configure User Stations ....................................................................................................31  
Exporting Router Configuration .........................................................................................33  
Importing Router Configuration .........................................................................................33  
Checking Audio/Video Routing Results.............................................................................33  
Saving the Paragon Switch’s Database...................................................................................34  
Updating Firmware...................................................................................................................34  
Reorganizing the Update List ............................................................................................37  
Disconnection...........................................................................................................................37  
Closing Paragon Manager .......................................................................................................38  
Synchronizing Database..........................................................................................................38  
Paragon Manager Help............................................................................................................38  
Appendix A: Client Software for Paragon II System Controller... 39  
Some Differences in the Shared Commands ..........................................................................40  
Connect (Session Menu)...................................................................................................40  
Create and Property (Users Menu) ...................................................................................41  
Exclusive Features in P2SC ....................................................................................................41  
RFT_Update (Setup Menu) ...............................................................................................41  
Base UMT’s (Setup Menu) ................................................................................................41  
About Paragon II System Controller Admin.......................................................................42  
ii  
FIGURES  
Figures  
Figure 1 Session Menu - Connect............................................................................................................... 3  
Figure 2 Paragon Manager Login Dialog - Connect..................................................................................... 3  
Figure 3 UMT Profile Dialog......................................................................................................................... 4  
Figure 4 Update Progress............................................................................................................................ 4  
Figure 5 Paragon Manager Window ............................................................................................................ 5  
Figure 6 Paragon Manager Window ............................................................................................................ 6  
Figure 7 Device Tree by Channel ................................................................................................................ 9  
Figure 8 Tiered Switch Example (Z-CIM)..................................................................................................... 9  
Figure 9 Device Tree by Type.................................................................................................................... 10  
Figure 10 Ghosted Channels Option in the View Menu ............................................................................. 11  
Figure 11 System Settings Dialog............................................................................................................. 12  
Figure 12 Add User Dialog......................................................................................................................... 14  
Figure 13 Change Password Dialog .......................................................................................................... 15  
Figure 14 User Information Dialog ............................................................................................................. 16  
Figure 15 Admin User Information Screen................................................................................................. 17  
Figure 16 Select Destination Path Dialog .................................................................................................. 17  
Figure 17 Confirm Load User Profile Dialog............................................................................................... 18  
Figure 18 Edit Log Settings Dialog............................................................................................................. 19  
Figure 19 Power Strip View Panel ............................................................................................................. 20  
Figure 20 Outlet Information Dialog ........................................................................................................... 20  
Figure 21 Channel Information Editor Dialog ............................................................................................. 21  
Figure 22 MFV with Channel Data............................................................................................................. 23  
Figure 23 MFV with Power Strip View Panel.............................................................................................. 23  
Figure 24 Add Multiple Port Association Dialog – Initial Screen................................................................. 24  
Figure 25 Add Multiple Port Association Dialog – Edit Data ...................................................................... 25  
Figure 26 Force Video Dialog .................................................................................................................... 26  
Figure 27 Router Menu .............................................................................................................................. 27  
Figure 28 Configure Routers Dialog........................................................................................................... 28  
Figure 29 Router Settings .......................................................................................................................... 28  
Figure 30 Configure Servers Dialog........................................................................................................... 29  
Figure 31 Source Association Table .......................................................................................................... 30  
Figure 32 Configure User Stations Dialog.................................................................................................. 31  
Figure 33 Destination Association Table.................................................................................................... 32  
Figure 34 Paragon Update Dialog.............................................................................................................. 35  
Figure 35 Paragon Update – Check All...................................................................................................... 36  
Figure 36 Paragon Device and File Version Information Window.............................................................. 36  
Figure 37 Wrong Firmware Warning Message........................................................................................... 37  
Figure 38 Paragon Update Progress Bar................................................................................................... 37  
Figure 39 Paragon Update Successful Message....................................................................................... 37  
Figure 40 Session Menu - Disconnect ....................................................................................................... 38  
Figure 41 Setup Menu – Synchronize Database........................................................................................ 38  
Figure 42 P2SC - System Controller Admin Login Dialog.......................................................................... 40  
Figure 43 P2SC – Add User Dialog ........................................................................................................... 41  
Figure 44 P2SC – Paragon System Configuration Dialog (No Data) ......................................................... 42  
Figure 45 P2SC – Paragon System Configuration Dialog (with Data) ....................................................... 42  
CHAPTER 1: INTRODUCTION  
1
Chapter 1: Introduction  
Paragon Manager Overview  
Paragon Manager is Raritan’s appliance management and configuration application, offering one  
coordinated graphical user interface that displays Device, User, Log, and Outlet information for  
your Paragon system. Paragon Manager allows you to add, modify, and delete Devices, Users, or  
Groups, and to specify log events to keep an audit trail of events that is updated in real time. In  
addition, you can also perform video redirection (called Forced Video), refresh IBM Blade  
server’s channel status, or associate channels for setting up concurrent multiple-video-output  
function (called Multiple Video or Port-Following Switch) in Paragon Manager. Paragon  
Manager can be downloaded from Raritan’s website.  
If working with a Paragon II configuration, first read the Paragon II User Guide for initial  
installation and configuration of your Paragon II devices. This document can be downloaded from  
the Firmware and Documentation section of Raritan website at:  
http://www.raritan.com/support/firmware-and-documentation/.  
For users who use Paragon II System Controller, see Appendix A: Client Software for Paragon  
II System Controller for the difference between P2SC Admin client software and Paragon  
Manager.  
Installing Paragon Manager  
Follow the steps below to download Paragon Manager.  
1. Use your browser to visit Raritan's Firmware and Documentation webpage  
(http://www.raritan.com/support/firmware-and-documentation/).  
2. Click Paragon II on the left pane to open its list of support documents and files.  
3. Locate the Other Support Files section on the right pane.  
4. Click the latest version of “Paragon Manager Admin Tool” to download Paragon Manager.  
5. (Optional) If this is your first time to download the program or firmware from the Raritan  
website, fill in the Firmware Request from, and click Submit.  
6. When you see the hyperlink on the right pane, click it.  
7. Specify the location where you want to save the file, and click Save. Wait until the download  
completes.  
8. Extract the file if it is a ZIP file.  
9. Double click the ParagonManager-setup.exe file to install Paragon Manager. Accept the  
default settings.  
When installation is complete, a shortcut to the application has been added to your Start menu  
 
2
PARAGON MANAGER USER GUIDE  
CHAPTER 2: OPERATION  
3
Chapter 2: Operation  
Connection and Login  
Only three types of users have permissions to log in to Paragon Manager:  
•
•
•
Administrators (the “Admin” account)  
Users with administrator privileges  
Users with Forced Video privileges  
Administrators and users with administrator privileges can manage or even modify the user or  
channel data in Paragon Manager, but users with Forced Video privileges do not have  
permissions to do this. The only thing they can do is to perform the Forced Video function.  
Establishing a Connection  
Follow the steps below to establish the connection to any Paragon II switch after Paragon  
Manager is launched:  
1. Choose Start > Programs > Paragon Manager. The Paragon Manager window appears.  
2. Choose Session > Connect.  
Figure 1 Session Menu - Connect  
The Paragon Manager Login dialog appears.  
Figure 2 Paragon Manager Login Dialog - Connect  
3. Type your user name in the User Name field.  
4. Type your password in the Password field.  
5. Decide your next action based on the Paragon switch displayed in the Select UMT field:  
•
•
If the desired Paragon switch is already displayed, go to step 6.  
If the desired Paragon switch is NOT displayed, click the arrow beside the field and  
select the desired Paragon switch from the drop-down list.  
•
If the desired Paragon switch is neither displayed nor available from the drop-down list,  
do the following to add it:  
a)  
Click the  
button. The UMT Profile dialog appears.  
   
4
PARAGON MANAGER USER GUIDE  
Figure 3 UMT Profile Dialog  
b)  
c)  
d)  
Click New.  
Type the name of the device in the UMT field.  
Select the TCP/IP option.  
•
•
•
Type the IP address of the Paragon switch in the IP Address field.  
Type the Port number of the Paragon switch in the Port field.  
Type the appropriate encryption key of the Paragon switch in the Encryption  
Key field, if applicable.  
e)  
f)  
Click Save to save this new device.  
Click Close to return to the login window.  
Note: To delete a Paragon switch in the UMT Profile dialog:  
(1) Click the drop-down arrow in the UMT field and select the device you wish to delete.  
(2) Click Delete to delete it.  
(3) Click Close to return to the login dialog.  
6. Click Login to log in to the Paragon switch. The Update Progress indicator displays your  
connection status. It may take 30 seconds or longer to connect, depending on your Paragon  
configuration.  
Figure 4 Update Progress  
 
CHAPTER 2: OPERATION  
5
7. When connected, the Paragon Manager window appears.  
Figure 5 Paragon Manager Window  
Note: See Disconnection for information on disconnecting the existing connection session,  
or see Closing Paragon Manager for information on closing the application.  
Paragon Manager Window Components  
The Paragon Manager window contains the Paragon Manager menu bar and toolbar, the Device  
panel, User panel, Log panel, and Power Strip View panel.  
•
•
•
•
The Device panel displays all connected devices in a single Paragon system.  
The User panel displays all users in your Paragon system.  
The Log panel displays the current activity of Paragon Manager.  
The Power Strip View panel displays any power strips connected to your Paragon  
system.  
When you connect to your Paragon switch via Paragon Manager, it downloads the device’s  
database and populates the Device, User, and Power Strip View panels automatically. Initial  
download may last several minutes, depending on the sizes of the client system and the Paragon  
system. Once a connection session is initiated, updates to the database happen in real time and  
changes to the Paragon database from other users are immediately reflected in your Paragon  
Manager screen.  
 
6
PARAGON MANAGER USER GUIDE  
Device panel -  
displays all  
connected  
devices in the  
Paragon II  
system  
Multi-Function  
View (MFV)  
panel – displays  
device and/or user  
information  
Power Strip View  
panel – displays  
power strips and  
connected ports  
Device View  
Tabs – view  
devices by  
Channel or by  
Type  
User panel –  
displays users  
and groups in  
the system  
Log panel –  
displays tracked  
events by date  
and time  
Figure 6 Paragon Manager Window  
 
CHAPTER 2: OPERATION  
7
Customize your view by resizing panels or by displaying or hiding any of these components,  
except for the Device panel. Select options on the View menu; click the desired panels in the  
menu to display or to hide them. A check mark before the menu item indicates that it is displayed.  
Only the Device panel cannot be hidden.  
Resize the window panels by resting your mouse cursor on the border of two panels until a  
double-headed arrow appears. Click and drag the arrow to size the panel up/down or left/right.  
Toolbar  
The toolbar displays shortcut buttons for the most commonly-used commands. These are  
explained in the table below.  
Note: Some of these shortcuts, as well as some menu commands, are also available by right-  
clicking on a User, Device, or Channel icon to activate a shortcut menu.  
Toolbar Shortcut Icons  
BUTTON  
ACTION  
Connect: Establishes a connection to the selected Paragon switch.  
Disconnect: Disconnects the existing connection session.  
Add User: Adds a new user account in Paragon Manager and the connected  
Paragon system.  
Delete Selected User: Deletes the user selected in the User View panel from  
Paragon Manager and the connected Paragon system.  
View by Channel: Displays devices by Channel.  
View by Type: Displays devices by Type.  
Synchronize Database: Activate the download process again to refresh  
Paragon Manager’s database.  
System Setting: Displays the connected Paragon’s system configuration.  
Log File: Launches the Edit Log Setting dialog for Administrators to  
configure event filters, event severity, and locations of saved log files.  
Help: Launches the Paragon Manager online help.  
 
8
PARAGON MANAGER USER GUIDE  
Device Panel  
The Device panel displays all devices connected to the Paragon switch to which you are  
connected. To make control easier, view devices either by Channel or by Type using the two tabs  
at the base of the Device panel (please see next section for additional information on Device  
views).  
ICON  
INDICATES:  
Power Strip outlet – power off (server)  
Power Strip outlet – power on (server)  
Power Strip outlet – power off (PWR)  
Power Strip outlet – power on (PWR)  
Channel Available  
Channel Available with one power strip outlet association  
Channel Available with multiple power strip outlet  
associations  
Channel Disconnected  
Channel Disconnected with one power strip outlet  
association  
Channel Disconnected with multiple power strip outlet  
associations  
Channel Occupied by a user  
Channel Occupied by a user, with one power strip outlet  
association  
Channel Occupied by a user, with multiple power strip  
outlet associations  
Power Strip Connected  
Power Strip Disconnected  
   
CHAPTER 2: OPERATION  
9
Device View  
View by Channel  
Click the View By Channel tab to display devices in a hierarchical tree by channel number. The  
icon at the top of the tree is the connected Paragon switch.  
Click the + symbol next to the Paragon switch to expand the tree and display all devices  
connected directly to it, listed in port number order. Target servers appear as computer icons.  
Figure 7 Device Tree by Channel  
Tiered switches (such as Z-CIM) appear as icons with the + symbol before them, and can also be  
expanded.  
Figure 8 Tiered Switch Example (Z-CIM)  
Grey computer icons represent a target server that is available for connection, while blue  
computer icons indicate that a user is accessing the target server. Red computer icons represent a  
target server that is unavailable. See the Device Panel table on the previous page for more  
information.  
 
10  
PARAGON MANAGER USER GUIDE  
View by Type  
Click the View By Type tab to display devices in a hierarchical tree by device type. Target  
Systems, Switches, and Power Strips are represented in this view.  
•
•
•
Switches are represented by a grey node.  
Target Systems are represented by a grey computer  
Power Strips are represented by a grey lightning bolt.  
Click the + symbol before any icon to expand the tree to display all devices of that type in the  
configuration, displayed by type in alphabetical order.  
Figure 9 Device Tree by Type  
 
CHAPTER 2: OPERATION  
11  
Ghosting  
In a Paragon system, when a CIM or tier device is removed from the system or powered off  
(manually or accidentally), a record of the CIM or CIMs connected to that tier device is reserved  
in the Paragon system. The target (or port) name will continue to appear in black text on the On-  
Screen Display (OSUI) of local user stations, and will also appear, with inactive status, in clients  
such as Raritan MPC (Multi-Platform Client), RRC (Raritan Remote Client), Paragon Manager,  
P2SC (Paragon II System Controller) Admin, and CC (CommandCenter).  
In versions of PCCI 1.2 and later (and with standalone Paragon 4.1 and later), the default  
Ghosting mode on the Paragon OSUI is set to Enable. When an active CIM is removed from one  
channel and connected to another channel (‘hot-swapped’), you will see two identical CIM entries  
on the OSUI of the Paragon Clients: one in green text (indicating that it is active) and another in  
black text (indicating that it is inactive). The inactive CIM is known as the ‘ghost’ CIM. To stop  
displaying records of the inactive CIMs after they are hot-swapped into a different port, you must  
set the Ghosting mode in Paragon to Disable.  
Even if Ghosting mode in your Paragon device is set to Disable, Paragon Manager allows the  
capability to override the ghost setting on the local machine. Choose View > Ghosted Channels  
to display any ghosted channels even though they are invisible throughout the rest of the Paragon  
system. This feature allows you to override the Ghosting preferences without changing settings of  
the entire system. It should be used for administration and for troubleshooting. Please see the next  
section for specifying Ghosting preferences for the system.  
Figure 10 Ghosted Channels Option in the View Menu  
 
12  
PARAGON MANAGER USER GUIDE  
System Setting  
Users of Paragon Manager for standalone Paragon product must set up their Paragon system  
configuration. Use the System Setting shortcut on the toolbar, or click System Setting on the  
Setup menu.  
1. Choose Setup > System Setting. The System Setting dialog appears.  
Figure 11 System Settings Dialog  
2. Type a name for your Paragon II switch in the System Name field (up to 12 alphanumeric  
characters). It is important for Paragon switches to have distinctive names if they are part of a  
cascaded system with multiple Base Units.  
3. Click the Operation Mode drop-down menu and select a mode. Operation Mode indicates  
the way your Paragon system handles requests from multiple users for access to the same  
channel port. Choose:  
−
Private: A server or other device on a specific channel port can be accessed exclusively  
by only one user at a time. No other users can control that device until its controlling user  
selects a different channel port.  
−
Public View (P-View): While one user is accessing a server or other device on a specific  
channel port, other users can select the same channel port and view the video output from  
that device, but only the first user will have keyboard and mouse control. When the first  
user selects a different channel port, the waiting user who is first to type or move the  
mouse is given keyboard and mouse control. Status messages showing users’ identities  
appear on video-sharing users’ monitors when Public View mode is in effect.  
−
PC Share: A server or other device on a specific channel port can be selected and  
accessed by more than one user, but only one user has keyboard and mouse control at any  
given time. If the PC share timeout is enabled and the user in control is idle (no keyboard  
or mouse activity) for the duration of the timeout, the waiting user who is first to type or  
move the mouse is given keyboard and mouse control of the PC.  
4. Click the Hide Admin From Users drop-down arrow and choose Yes or No. When  
Operation Mode is set to “Public View” (P-View), the user in control of a server is normally  
notified when other users start and stop viewing the channel port’s video. However, when  
Hide Admin From Users is set to “Yes,” administrators can view other users’ video without  
activating this viewing-notification message. The default setting is No.  
 
CHAPTER 2: OPERATION  
13  
5. Click the Login Sleep drop-down arrow and choose OFF, Saver or Green. If you choose  
Saver or Green, specify the amount of time in minutes that the local user station can remain  
inactive at the Login Menu before the monitor enters the power-saving mode (press any of  
the keys on the keyboard to restore normal video). Using leading zeroes if necessary, type in  
a two-digit number of minutes from 01 to 99 in the Interval (Min.) field which is next to the  
Login Sleep field. The default setting is 05. The difference between Green and Saver is the  
Saver option makes the monitor go blank with a floater displayed on the screen, but without a  
floater for the Green option. If the Login Sleep is set to “Off,” the number in this field will  
have no effect.  
6. Click the Default Login Name Blank drop-down arrow and choose Yes or No. This  
determines whether the User Name field in the Login Menu will be blank when the menu  
appears, or if the field will contain the default user name (the first available “userxy” name,  
where “xy” is a two-digit number with leading zeroes—“user01,” “user02,” and so on). Use  
the Ç and È keys to toggle between “Yes” (the field is blank – the default value) and “No”  
(field contains the user name).  
7. Click the Logoff Timeout drop-down arrow and choose On or Off. If enabled, the amount of  
time in minutes that the local user station can remain inactive before the logged-in user at that  
station is logged out of the Paragon II system.  
−
If Logoff Timeout field, above, is set to “On,” the number in the Interval (Min.) field  
(the one near the Logoff Timeout field) is the number of minutes of inactivity before the  
timeout is triggered and the user is logged out. Using leading zeroes if necessary, type in  
a two-digit number of minutes from 01 to 99. The default setting is 05. If Logoff Timeout  
is set to “Off,” the number in this field will have no effect.  
8. Type the timeout (in seconds) in the PCShare Timeout (Sec) field. If Operation Mode is set  
to “PC Share” and more than one user has selected a server, the first user to type or use  
his/her mouse will have control of the server. However, another user can gain control of the  
server if the first user’s keyboard and mouse remain idle for the length of this timeout. Using  
leading zeroes if necessary, type in a two-digit number of seconds from 01 to 99. The default  
setting is 01.  
9. Click the Require Password drop-down arrow and choose Yes or No. Determine whether a  
user can specify a blank password, that is, delete any existing password and have no  
password at all. Use the Ç and È keys to toggle between “No” (users may delete their  
existing passwords) and “Yes” (the default setting; starting with the first time they change  
their password, users must always have a non-blank password). Newly created users always  
start with no password, and must assign one to themselves during initial setup.  
10. Click the Ghost Mode drop-down arrow and choose Enable or Disable. If you enable  
ghosting, you will be able to view hot-plugged CIM connections, former and current. If you  
disable ghosting, you will see only current CIM connections. The default setting is Enable.  
11. When finished, click Ok to accept all system settings, or click Cancel to close this screen  
without saving changes.  
14  
PARAGON MANAGER USER GUIDE  
User Panel  
The User panel displays users stored on the connected Paragon system and displays each user’s  
profile.  
Double-click a user to display the User Information dialog. As an Administrator, you can change  
account properties for users selected in this dialog.  
ICON  
INDICATES:  
Admin logged in and Connected  
Admin logged in and Disconnected  
Admin logged out and Disconnected  
User logged in and Connected  
User logged in and Disconnected  
User logged out and Disconnected  
Creating a User  
1. Choose Users > Create. The Add User dialog appears.  
Figure 12 Add User Dialog  
2. Type the new user’s name in the User Name field.  
   
CHAPTER 2: OPERATION  
15  
3. Click Change and the Change Password dialog appears. Type a new password in the Enter  
New Password field, and re-type the password in the Repeat Password field. Click OK  
when finished.  
Figure 13 Change Password Dialog  
4. The Security Groups field is automatically populated, based on the defaults of the Paragon  
switch to which you are connected. To change the assigned Security Groups, click Set  
Security Group and change the default groups (please consult your Paragon User Guide for  
more information on Security Groups).  
5. Click the Allow Administrator Privileges drop-down arrow and select an option from the  
list.  
6. In the User Options panel, click the Scan Mode drop-down arrow and select the scan mode  
for this user. Global scan mode, the default, scans each channel for the same amount of time  
(default time = three seconds), and Individual scan mode scans each channel for a specific  
time the Administrator has specified on the OSUI. To change the number of seconds for the  
Global scan, type the new duration of seconds in the Scan Time (Sec) field.  
7. Click the Hot Key drop-down arrow and select a key from the list. When you press this key  
twice rapidly on any user station in your Paragon configuration, the Paragon OSUI will  
appear. Note that this option is set in Paragon Manager, but used only at local user stations in  
the Paragon system.  
8. Click the Previous Channel drop-down arrow and select a key from the list. When you press  
this key on any user station in your Paragon configuration, the channel previously viewed  
will re-appear. Choose None to override this capability. Note that this option is set in Paragon  
Manager, but used only at local user stations in the Paragon system.  
9. Click the Sleep Mode (min) drop-down arrow and turn the power-saving mode off or on  
(that is, Saver or Green). If you select Saver or Green, type in the number of minutes after  
which, if there is no keyboard or mouse activity, the user station monitor goes blank with a  
floater displayed (Saver) or without a floater displayed (Green) on the screen.  
10. The Help Display determines how the Paragon help screen is activated from any user station  
in your Paragon configuration.  
11. Click the ID Display (sec) drop-down arrow to turn the ID display Off or On. If you select  
On, the ID Display will remain on the user station monitor for the number of seconds you  
type into the next field.  
12. In the Menu Position and ID Display Position panels, enter the Horizontal and Vertical  
placement of the menu on any of the user station monitors in your Paragon configuration.  
13. Allow Force Video Privileges field: An administrator or user with administrator privileges is  
by default capable of performing the Forced Video function (video redirection). However, to  
allow a user without administrator privileges to be able to execute this function, you need to  
specify the privileges for that user. Please note if you have more than one Paragon switch in  
your Paragon system, you may need to connect to diverse Paragon switches to configure the  
Force Video privileges for the same user since each Paragon switch stores their user data  
respectively. Choose ON to authorize the privileges to the user or OFF to disable the  
privileges.  
14. Click OK when finished, or click Cancel to exit without adding a new user.  
 
16  
PARAGON MANAGER USER GUIDE  
Deleting a User  
Deleting a user in the Paragon Manager window deletes the user account from both the Paragon  
Manager screen and also from the currently connected Paragon system.  
1. In the User panel, click the user you want to delete.  
2. Choose Users > Delete. The Confirm User Delete dialog appears.  
3. Click Yes to delete the user or click No to close the dialog without deleting.  
Note: The Administrator (Admin) cannot be deleted.  
Viewing User Properties  
Administrators can modify user properties in Paragon Manager.  
1. In the User panel, click the user whose properties you want to modify, or simply double click  
it.  
2. Choose Users > Property, or right-click that user and choose Property from the pop-up  
menu. The User Information dialog appears.  
Figure 14 User Information Dialog  
3. Change any of the user’s properties, according to the guidelines just outlined in the section  
Creating a User.  
4. When finished, click OK to change the user properties or click Cancel to close the dialog  
without saving any changes.  
 
CHAPTER 2: OPERATION  
17  
Not all of the Administrator User’s (Admin) properties can be changed. If you select the Admin  
icon in the User panel and activate the Admin’s User information dialog, those properties are  
grayed out, as illustrated below. Properties that cannot be changed include User Name, Allow  
Administrator Privileges, Allow Force Video Privileges, Set Security Groups, and Help  
Display.  
Figure 15 Admin User Information Screen  
Saving User Profiles  
As an Administrator, you can back up the User Database of the connected Paragon system to your  
local computer using the Save Profile command.  
1. Choose Users > Save Profile. The Select destination path dialog appears.  
Figure 16 Select Destination Path Dialog  
2. Browse through the local system until you find the location where you want to save the  
Profile. Type the name of the file in the File Name field and click Save. A confirm message  
box will display the path to the folder and file you just chose. Click OK to close the message  
box.  
 
18  
PARAGON MANAGER USER GUIDE  
Loading a User Profile  
Use the Load Profiles command to restore previously backed-up Paragon Manager files.  
1. Choose Users > Load Profiles. The Confirm Load User Profile dialog appears.  
Figure 17 Confirm Load User Profile Dialog  
2. Click Yes to load existing user profiles, or click No to exit the dialog.  
Note: If you load a user profile for a user currently in Paragon Manager, the older profile  
will replace the new profile.  
Important: The Load Profiles command can be used to restore previously saved  
Paragon Manager system database files (*.mxd files) from an older Paragon HW3  
configuration.  
 
CHAPTER 2: OPERATION  
19  
Log Panel  
Editing Event Log Settings  
The Log panel located at the base of the Paragon Manager window displays events that occur in  
your Paragon system(s). As the Administrator, you can record and configure standard events and  
message filters, and set severity levels for events, color-coding them for easier identification.  
1. Choose Setup > Log Setting. The Edit Log Setting dialog appears.  
Figure 18 Edit Log Settings Dialog  
2. Click the + and – signs to expand and collapse the event tree in this window. Entries in the  
event tree are pre-determined events programmed into Paragon Manager.  
3. Click the checkbox before a device to select and specify events for recording in the log  
panel. Select an event for the device.  
4. On the right side of the window, click the Set Severity Level drop-down arrow and select a  
severity level – levels are color-coordinated: high severity is represented by a red icon,  
medium severity is blue, and lowest severity is black. To restore the default levels for the  
events, click Restore.  
5. In the Log File Setting panel, the location for saved log files appears in the Select Log File  
field. The default location is C:/Documents and Settings (username). To change this default  
location, click Browse and locate the folder in which you want to store log files.  
6. Click the Size (MB) drop-down arrow to select the file size limit (default limit is 4MB).  
Once the log file hits the size limit set in this field, Paragon Manager automatically creates a  
new log file and continues to store events.  
7. Click OK to save the log settings, or click Cancel to close the dialog without saving any  
changes.  
 
20  
PARAGON MANAGER USER GUIDE  
Power Strip View Panel  
The Power Strip View panel is a mobile display of Raritan Remote Power Control Strips  
connected to your Paragon switch. Each node in the Power Strip tree represents a power strip, and  
you can click the + and – signs to expand and collapse the view of devices plugged into each of  
the serially-controlled Power Strip outlets. If the Power Strip View panel is not visible, choose  
View > Power Strip.  
Figure 19 Power Strip View Panel  
Paragon Manager automatically detects Raritan Power Strips connected to your Paragon system.  
Click any Power Strip in the tree to view its outlets. Click the + and – signs to expand and  
collapse the view. Right-click any Power Strip outlet to view its properties.  
Editing Power Strip Data  
To organize the Power Strips in your Paragon configuration and to keep track of the machines to  
which they are connected, you may want to name the Power Strips and outlets.  
1. Double-click any Power Strip icon to view its properties. The Outlet Information dialog  
appears.  
Figure 20 Outlet Information Dialog  
2. The default name of the strip appears in the Power Strip Name field. Type a new name if  
needed.  
3. The Outlet # field is automatically populated and cannot be changed.  
4. Click the Outlet Type drop-down arrow to select either a Power (PWR) or CPU type outlet.  
5. Type the name of the outlet in the Outlet Name field.  
 
CHAPTER 2: OPERATION  
21  
6. Type the Security Group in the Security Group field.  
7. Click OK to save the changes, or click Cancel to close the window without saving any  
changes.  
Note: Because the Power Strip cannot detect what device type is associated with a specific  
outlet through the power cables, outlet associations must be created manually before an  
outlet can indicate to what type of device it supplies power.  
Power Strip Outlet Associations  
You can assign specific devices to unassigned Power Strip Outlets from the Paragon Manager  
interface.  
1. Expand the Power Strip tree so you can see the outlet to which you plan to assign the selected  
device.  
2. Click a device in the Device panel and drag the Device icon to the desired outlet icon.  
3. When you release the device, a confirm message box appears. Click Yes to associate Device  
to this outlet or click No to cancel this action. You can now control the Device from the  
Paragon OSUI.  
Note 1: For devices with redundant power supplies, one device can be associated with up to  
four outlets.  
Note 2: Paragon Manager only allows you to configure the power strip association setting.  
You cannot use it to control the associated power strip. To control the power strip, you must  
use the Paragon OSUI. For more information, see Paragon II User Guide, which can be  
downloaded from the Firmware and Documentation section of Raritan’s website:  
http://www.raritan.com/support/firmware-and-documentation/.  
Channel Information Editor  
To view the properties or change the name of channel:  
1. Select the target channel in the Device View panel.  
2. Right click the highlighted channel and select Property. The Channel Information Editor  
dialog appears.  
Figure 21 Channel Information Editor Dialog  
-
-
Name: Give the device on this channel a name.  
Type: Select what type of device this is, CPU for target servers or any of the Raritan  
PowerStrips or non-Paragon switches available in the list.  
Depending on the Type selected, further information may be available in the dialog.  
-
Status: Displays the current status of a target device on this channel.  
 
22  
PARAGON MANAGER USER GUIDE  
-
-
-
Security Group: The security groups the target device belongs to (This only affects  
local Paragon access from outside of CommandCenter).  
Associated Outlets: Lists any power outlets associated with this target device. Select  
an outlet and click Remove to break an association.  
Serial Number: Displays the serial number of a non-CPU type device.  
3. Click OK to save your changes when done, or Cancel to exit without saving.  
4. After saving the channel information, this device can be recognized by the given name in  
both the System Controller Admin and the CommandCenter Configure Ports screen.  
CHAPTER 2: OPERATION  
23  
Multi Function View (MFV) Panel  
The Multi Function View (MFV) panel of the screen displays detailed information of items you  
select in the Device panel, User panel, or Power Strip panel and allows Administrators to edit  
item properties from this list.  
If you select a device in the Device tree, the MFV displays target-related information: name,  
device type, security group, and device status. If you select a user in the User tree, the MFV  
displays user-related information: user name, Admin status, security group, scan rate, and  
connection information. If you select a power strip outlet, the MFV displays outlet name and  
connected device type.  
Administrators can double-click an entry in the MFV to activate the properties dialog for that  
entry, and modify data for devices, users, or outlets, as described in the respective sections of this  
chapter.  
Figure 22 MFV with Channel Data  
Figure 23 MFV with Power Strip View Panel  
 
24  
PARAGON MANAGER USER GUIDE  
Setting Up Multiple Video Function  
Multiple Video allows users to leverage a server’s numerous video ports, providing enhanced  
flexibility in video access and port operations.  
Multiple Video, also known as “Port Following Switch,” enables multiple user stations (2 or 4) to  
simultaneously view the video output of a single server that has more than one video port.  
Multiple Video may also be used to send video from separate servers to sequential user stations.  
This function is executed through the Paragon OSUI, but must be configured in Paragon Manager  
first. Always remember that only channels on the same Paragon switch can be associated as one  
group. Up to 256 association groups can be set per Paragon system.  
Note: Anyone can perform the Multiple Video function on the Paragon OSUI, but only the  
Administrator or users with administrator privileges can set up the channel association in  
Paragon Manager.  
Adding an Association Group  
In order to perform Multiple Video, you must set up the channel association. One association  
group consists of 2 or 4 channels, but each channel is associated in one group only.  
1. Choose Setup > Multiple Video. The Add Multiple Port Association dialog appears.  
Figure 24 Add Multiple Port Association Dialog – Initial Screen  
2. Click New to start creating an association setting.  
3. Type a name in the Association Name field to identify this association group. Up to 20  
characters can be entered.  
4. Click the UMT drop-down arrow and select the Paragon switch whose channels you are  
going to associate. By default, each Paragon switch’s name is followed by its serial number.  
5. Click the Viewing Mode drop-down arrow, and select the desired option, as explained below.  
−
−
Dual Screens associates two channels.  
Quad Screens associates four channels.  
 
CHAPTER 2: OPERATION  
25  
6. Click the First Channel drop-down arrow and select the channel number that will be able to  
activate video outputs of other channels when it is accessed.  
7. Click the Second Channel drop-down arrow and select the channel number whose video  
output will be activated when the first channel is accessed.  
8. Repeat step 7 for Third and Fourth Channel if you choose “Quad Screens” in Step 5.  
9. Choose the desired action(s) from the following:  
•
•
•
•
Click OK to save changes and exit the dialog.  
Click Apply to save changes without exiting the dialog.  
To exit the dialog without saving any changes, click Close.  
If you want to create more association groups, repeat steps 2 to 9 to complete each  
association setting.  
Editing an Association Group  
You can modify any existing association group to meet your needs instead of creating a new  
association group from scratch.  
1. Choose Setup > Multiple Video. The Add Multiple Port Association dialog appears.  
2. Click the association group that you want to edit from the list on the lower part of the dialog.  
Figure 25 Add Multiple Port Association Dialog – Edit Data  
3. (Optional) If you want to change the total number of channels, click the Viewing Mode drop-  
down arrow and select the appropriate option.  
4. Change the channel configuration.  
5. Click Apply to save the changes, or Close to exit the dialog without saving any changes.  
Deleting an Association Group  
You can remove any unnecessary or obsolete association group from the list.  
1. Choose Setup > Multiple Video. The Add Multiple Port Association dialog appears.  
 
26  
PARAGON MANAGER USER GUIDE  
2. Click the association group that you want to delete from the list on the lower part of the  
dialog.  
3. Click Delete.  
4. Click Y to delete the group, or N to abort the deletion.  
Video Redirection (Forced Video)  
You can direct a channel output its video/keyboard/mouse signals to a specific user station and  
thus display the video image on that user station’s monitor. Please note that the signals can only  
be directed to a user station connected to the same Paragon switch. By default, only an  
administrator user can perform the function. To allow a non-administrator user to execute it, see  
the description of Force Video setting in Creating a User for related information.  
1. First connect to the Paragon switch on which you want to perform Forced Video. See  
Connection and Login for more information.  
2. Perform Forced Video through one of the following methods:  
•
Click the channel of the target server in the Channel panel, and then choose Setup >  
Force Video.  
•
Right-click the channel of the target server in the Channel panel, and select Force Video  
from the pop-up menu.  
The Force Video dialog appears.  
Figure 26 Force Video Dialog  
3. Click the User Port drop-down arrow and select the user port to which the desired user  
station is connected.  
4. Click OK.  
Refreshing IBM Blade Channel Status  
The Paragon switch does not automatically detect and reflect the real-time IBM Blade server  
status. To update the channel status, you can perform the “RefreshBLD-I” command on the OSUI  
or in Paragon Manager. For information on using OSUI to refresh the IBM Blade channel status,  
see Paragon II User Guide, which can be downloaded from the Firmware and Documentation  
section of Raritan’s website: http://www.raritan.com/support/firmware-and-documentation/.  
1. Verify whether the Device View panel sorts channels by channel numbers. If not, click the  
View By Channel tab.  
2. Locate the IBM BladeCenter chassis channel, which is preceded with a plus sign.  
3. Right-click the channel and select Property. The Channel Information Editor dialog  
appears.  
4. Type RefreshBLD-I in the Name field. Note the command is case-sensitive.  
5. Click OK and the Paragon system updates IBM Blade channel status for 2 to 4 minutes.  
Paragon Manager does not save “RefreshBLD-I” as a channel name so the IBM BladeCenter  
chassis channel will restore its original name.  
 
CHAPTER 2: OPERATION  
27  
Setting Up NV5128 Router Association  
Paragon version 4.6 or later supports audio/video routing when working with the NVISION®  
NV5128 multi-format router and Paragon Manager 2.0.3 or later.  
To activate this function, the router association data is required. With the router association data,  
Paragon Manager can command the NV5128 router to direct audio/video signals from specified  
audio/video sources to specified audio/video destinations when any access to Paragon channels  
occurs.  
Important: The audio/video routing function is applicable to a “one-tier” configuration  
only, which comprises a single Paragon Main Unit or a combination of a Paragon Main  
Unit and Stacking Unit(s). You can associate the router with a maximum of 16 user  
ports and 128 channel ports in the Paragon system.  
Overview of the Router Menu  
The Router menu provides all commands necessary to deal with the router association.  
Figure 27 Router Menu  
To create the router association data from scratch, three commands are necessary:  
•
•
•
Configure Routers  
Configure Servers  
Configure User Stations  
To save new router association data or the changes made to existing data, use this command:  
Export Router Configuration  
•
To import any existing router association data into Paragon Manager, use this command:  
Import Router Configuration  
•
Configure Routers  
Specify one or more NV5128 routers that you want the Paragon switch to associate with in  
Paragon Manager.  
Adding NV5128 Routers  
1. Choose Router > Configure Routers. The Configure Routers dialog appears.  
 
28  
PARAGON MANAGER USER GUIDE  
Figure 28 Configure Routers Dialog  
2. Click New to start adding a router.  
3. Type the NV5128 router’s IP address in the IP Address field.  
4. Ensure the TCP Port Number field displays 5194.  
Important: Do not change the TCP port number, or Paragon Manager cannot  
control the NV5128 router.  
5. Type a name in the Router Name field for identifying the router.  
6. (Optional) Type any descriptive text in the Description field.  
7. Do one of these:  
•
Click Apply to save the changes and the router setting is displayed in the table to the  
right. Repeat Steps 1 to 7 if you want to add more NV5128 routers.  
•
•
Click OK to save the changes and quit the dialog.  
Click Close to quit the dialog without saving the changes.  
Editing NV5128 Router Settings  
You can change existing router settings if IP address of any NV5128 router has been changed or  
is incorrect.  
1. Choose Router > Configure Routers. The Configure Routers dialog appears.  
2. Click the row containing the router settings that you want to change in the table. The  
highlighted router’s settings are all displayed in the fields to the left.  
Figure 29 Router Settings  
3. Change any field you want except for the Router Name field.  
4. Do one of these:  
•
Click Apply to save the changes, and then the changes are reflected in the table. Repeat  
Steps 1 to 4 if you want to edit more NV5128 router settings.  
•
•
Click OK to save the changes and quit the dialog.  
Click Close to quit the dialog without saving the changes.  
 
CHAPTER 2: OPERATION  
29  
Removing NV5128 Routers  
You can delete any existing NV5128 routers from Paragon Manager so that Paragon Manager can  
no longer control it. When you delete the router, all association data relevant with the router is  
removed, either.  
1. Choose Router > Configure Routers. The Configure Routers dialog appears.  
2. Click the row containing the router that you want to remove from the table.  
3. Click Delete.  
4. A confirmation message appears. Click Yes to remove the router or No to abort the removal.  
5. Repeat Steps 1 to 4 if you want to remove more routers.  
6. Click Close to quit the dialog.  
Configure Servers  
Channels ports on a Paragon switch usually connect to servers, and source ports (input connectors)  
on a NV5128 router connect to audio/video output devices. To determine which audio/video  
output devices the router should output audio/video signals when you access any Paragon channel  
port, you must associate channel ports with the source ports. A channel port can be associated  
with a maximum of 8 source ports, and each source port can be associated with one channel port  
only.  
Adding Source Association Data  
1. Choose Router > Configure Servers. The Configure Servers dialog appears.  
Figure 30 Configure Servers Dialog  
2. Click New to start adding source association data.  
3. Click the UMT Name drop-down arrow and select the Paragon Base Unit to which the  
Paragon Manager is connecting.  
4. In the Server field, select the channel port on the Paragon switch that you want to associate  
with the router’s source port(s). Click the left drop-down arrow to select the channel number  
and the right drop-down combo box will show the channel name if any.  
5. Click the Router Name drop-down arrow and select the NV5128 router whose source ports  
you want to associate with.  
6. This step varies depending on your physical hardware configuration:  
•
To associate all ports based on identical port numbers:  
a. Click Reset to Defaults.  
b. A confirmation message appears. Click Yes to reset. Then each channel port is  
associated with a source port if they share the same port numbers. Note that the port  
type of all source association data is set to Audio by default.  
•
To associate the ports at a random sequence:  
 
30  
PARAGON MANAGER USER GUIDE  
a. Click the Source Port drop-down arrow and select the source port to associate with.  
b. Click Audio if the selected source port is an audio connector, or Video if it is a video  
connector. The default is Audio.  
7. If you associate the ports at a random sequence in Step 6, do one of these:  
•
Click Apply to save the changes and the new association data is displayed in the table to  
the right. Repeat Steps 1 to 7 if you want to add more source association data.  
•
•
Click OK to save the changes and quit the dialog.  
Click Close to abort the changes and quit the dialog.  
Editing Source Association Data  
You can change existing source association data when any setting is incorrect or if you have  
made changes to the physical hardware configuration. For example, you may have moved the  
audio/video output devices from one source port to another source port or to a different NV5128  
router.  
1. Choose Router > Configure Servers. The Configure Servers dialog appears.  
2. Click the row containing the source association settings that you want to change in the table.  
The highlighted data’s settings are all displayed in the fields to the left.  
Figure 31 Source Association Table  
3. Change any field you want except for the UMT Name and Server fields, or click Reset to  
Defaults to reset all source association settings based on identical port numbers.  
4. Do one of these:  
•
Click Apply to save the changes, and then the changes are reflected in the table. Repeat  
Steps 1 to 3 if you want to edit more source association settings.  
•
•
Click OK to save the changes and quit the dialog.  
Click Close to quit the dialog without saving the changes.  
Removing Source Association Data  
You can remove any invalid source association settings from the table.  
1. Choose Router > Configure Servers. The Configure Servers dialog appears.  
2. Click the row containing the source association settings that you want to remove from the  
table.  
3. Click Delete.  
4. A confirmation message appears. Click Yes to remove the source association data or No to  
abort the removal.  
5. Repeat Steps 1 to 3 if you want to remove more source association data.  
 
CHAPTER 2: OPERATION  
31  
6. Click Close to quit the dialog.  
Note about “Reset to Defaults”  
You can click Reset to Defaults to save time configuring the source association data when the  
Paragon channel ports and the router’s source ports are associated with each other based on the  
same port numbers. The command has these characteristics:  
•
•
All existing source association data is cleared and replaced by new data.  
All channel ports will be associated with source ports based on identical port numbers. That  
is, channel port 1 is associated with source port 1, channel port 2 with source port 2, channel  
port 3 with source port 3, and so on.  
•
•
The number of associated ports is determined according to the number of channel ports.  
Port type is set to audio by default.  
Configure User Stations  
User ports on a Paragon switch connect to user stations, and destination ports (output connectors)  
on a NV5128 router connect to audio/video input devices. To determine which audio/video input  
devices should receive the audio/video signals transmitted by the router, you must associate user  
ports with destination ports. Usually your association settings should be able to direct the  
audio/video signals to the audio/video input devices located near a user station. A user port can be  
associated with a maximum of 8 destination ports, and each destination port can be associated  
with one user port only.  
Adding Destination Association Data  
1. Choose Router > Configure User Stations. The Configure User Stations dialog appears.  
Figure 32 Configure User Stations Dialog  
2. Click New to start adding destination association data.  
3. Click the UMT Name drop-down arrow and select the Paragon Base Unit to which the  
Paragon Manager is connecting.  
4. Click the User Port drop-down arrow, and select the user port on the Paragon switch that you  
want to associate with the router’s destination port(s).  
5. Click the Router Name drop-down arrow and select the NV5128 router whose destination  
ports you want to associate. The router must be the same one that you selected in the  
Configure Servers dialog.  
6. This step varies depending on your physical hardware configuration:  
•
To associate all ports based on identical port numbers:  
a. Click Reset to Defaults.  
 
32  
PARAGON MANAGER USER GUIDE  
b. A confirmation message appears. Click Yes to reset. Then each user port is associated  
with a destination port if they share the same port numbers. Note that port type of all  
destination association data is set to Audio by default.  
•
To associate the ports at a random sequence:  
a. Click the Destination Port drop-down arrow and select the destination port to  
associate with.  
b. Click Audio if the selected destination port is an audio connector, or Video if it is a  
video connector. The default is Audio.  
7. If you associate the ports at a random sequence in Step 6, do one of these:  
•
Click Apply to save the changes and the new association data is displayed in the table to  
the right. Repeat Steps 1 to 7 if you want to add more destination association data.  
•
•
Click OK to save the changes and quit the dialog.  
Click Close to abort the changes and quit the dialog.  
Editing Destination Association Data  
You can change existing destination association data when any setting is incorrect or if you have  
made changes to the physical hardware configuration. For example, you may have moved the  
audio/video input devices from one user station to another user station or reconnected them to a  
different NV5128 router.  
1. Choose Router > Configure User Stations. The Configure User Stations dialog appears.  
2. Click the row containing the destination association settings that you want to change in the  
table. The highlighted data’s settings are all displayed in the fields to the left.  
Figure 33 Destination Association Table  
3. Change any field you want except for the UMT Name and User Port fields, or click Reset to  
Defaults to reset all destination association settings based on identical port numbers.  
4. Do one of these:  
•
Click Apply to save the changes, and then the changes are reflected in the table. Repeat  
Steps 1 to 3 if you want to edit more destination association settings.  
•
•
Click OK to save the changes and quit the dialog.  
Click Close to quit the dialog without saving the changes.  
Removing Destination Association Data  
You can remove any invalid destination association settings from the table.  
1. Choose Router > Configure User Stations. The Configure User Stations dialog appears.  
2. Click the row containing the destination association settings that you want to remove from  
the table.  
3. Click Delete.  
4. A confirmation message appears. Click Yes to remove the destination association data or No  
to abort the removal.  
5. Repeat Steps 1 to 3 if you want to remove more destination association data.  
6. Click Close to quit the dialog.  
 
CHAPTER 2: OPERATION  
33  
Note about “Reset to Defaults”  
You can click Reset to Defaults to save time configuring the destination association data when  
the Paragon user ports and the router’s destination ports are associated with each other based on  
the same port numbers. The command has these characteristics:  
•
•
All existing destination association data is cleared and replaced by new data.  
All user ports will be associated with destination ports based on identical port numbers. That  
is, user port 1 is associated with destination port 1, user port 2 with destination port 2, user  
port 3 with destination port 3, and so on.  
•
•
The number of associated ports is determined according to the number of user ports.  
Port type is set to audio by default.  
Exporting Router Configuration  
After creating or changing the router association data, involving source and destination  
associations, you should save the data by exporting it for future use, or all association settings or  
changes you made will be lost when you exit from Paragon Manager or disconnect the Paragon  
system.  
1. Choose Router > Export Router Configuration. The Select destination path dialog appears.  
2. Ensure the file type shows XML Files.  
3. Navigate to appropriate location, specify the filename and click Save. It is recommended to  
name the file based on the Paragon switch’s name for easy identification of the file when  
importing the data in the future.  
Note: All characters that are present in the File name filed are regarded as the filename so  
you should remove unnecessary characters, including the extension, from this field when  
necessary.  
Importing Router Configuration  
Paragon Manager does not automatically import any previously-saved router association data so  
you must either create the router association data from the scratch or import existing router  
association data. This section explains how to import existing data.  
1. Choose Router > Import Router Configuration. The Select File to Import dialog appears.  
2. A confirmation message appears. Click Yes to import the selected data or No to cancel.  
3. Ensure the file type selects XML Files.  
4. Navigate to where the router association data specific to the Paragon switch is stored, select  
the appropriate file and click Open.  
Note: The router association data is Paragon switch-specific. If you import any router  
association data that is not for the connected Paragon switch, an error message appears,  
indicating that the UMT ID is different.  
Checking Audio/Video Routing Results  
Paragon Manager has a log panel at the bottom to display Paragon Manager activity. When  
Paragon Manager makes the router route audio/video signals based on the association data, the  
log panel records the activity and outcome.  
 
34  
PARAGON MANAGER USER GUIDE  
There are two types of routing records as explained in the table.  
Type 1  
This message indicates that Paragon Manager fails to connect to the NV5128  
router with the IP address 192.168.84.222. Check the router network settings and  
cabling when the connection error occurs.  
Type 2  
These messages indicate that Paragon Manager successfully connects to the  
NV5128 router with the IP address 192.168.84.207 and the other router with the  
IP address 192.168.84.192, and whether the routing for each audio/video source is  
successfully carried out.  
The information from left to right includes:  
•
•
•
•
User port number, indicating the user station you are operating  
Router’s IP address  
Source and destination port numbers, indicating the routing path  
Routing result (success, destination lock, and so on)  
Saving the Paragon Switch’s Database  
You can save the database of the connected Paragon switch, including system settings and  
channel configuration, as an XML-formatted file for your own backup or review purpose.  
1. Choose Help > Save XML Configuration. The Select destination path dialog appears.  
2. Navigate to the location where you want to save the file and specify the file name.  
3. Click Save.  
Updating Firmware  
In Paragon Manager, you can activate the firmware update utility—Paragon Update, in order to  
update your Paragon switch or even the user station’s firmware version. To update the firmware,  
first download the latest firmware file from Raritan’s website.  
To locate the firmware file:  
1. Use your browser to visit the Firmware and Documentation section  
(http://www.raritan.com/support/firmware-and-documentation/).  
2. Scroll down the page and click Paragon II to open a list of support documents and files.  
3. Click the latest version to locate the latest firmware file for your device.  
After downloading the file, unzip it, and then do the following:  
Important: If the device you are going to upgrade is a Paragon switch, it is strongly  
recommended to back up the user profile prior to the upgrade. Otherwise, you may  
need to reconfigure specific user data, such as user passwords, after the upgrade.  
To update the firmware file:  
1. Choose Setup > Firmware Update.  
2. The Confirm Disconnect message box appears. Click Yes to disconnect the existing  
connection session.  
 
CHAPTER 2: OPERATION  
35  
3. The Paragon Update dialog appears.  
Figure 34 Paragon Update Dialog  
4. If the device(s) intended to upgrade are listed in the dialog, go to Step 5. If not, click New to  
add the device(s) and click each field to enter or select the appropriate data, which is  
explained below:  
Depending on the manner in which the computer running Paragon Manager is connect to the  
desired devices, you may update the firmware through the network or the RS-232 connection.  
For example, updating a Paragon I switch requires the RS-232 connection, and updating a  
Paragon II switch requires the network connection.  
FIELD  
DATA TO ENTER OR CHOOSE  
Name  
Type the name of the desired KVM switch or user station.  
•
•
•
Network connection: Type the IP address of the Paragon  
switch.  
RS-232 connection: Choose <Default Serial> from the  
drop-down list.  
Network connection: Type the number of the appropriate  
network port. This setting must be the same as the port  
setting on the OSUI of the Paragon switch. The factory  
default port is 3000.  
IP Address/Serial  
Port  
•
•
RS-232 connection: Type the number of the serial port  
(COM port) that is connected to the desired KVM switch or  
user station.  
Network connection: If you have assigned encryption keys  
for the Paragon switch in the OSUI’s network setting, you  
must type the same encryption keys here. Otherwise, both of  
the connection and firmware upgrade will fail. If there are  
no encryption keys, choose <Default No Encryption>.  
RS-232 connection: Always choose <Default No  
Encryption>.  
Encryption Key  
•
 
36  
PARAGON MANAGER USER GUIDE  
Click Save to store the current list of devices so next time when you execute the Paragon  
Update utility, the same list appears and saves your time re-entering the same information.  
Note: The devices checked (3) on the list must all belong to the same type. For example,  
either all of them are Paragon switches or all are user stations.  
5. Select the checkboxes of the devices whose firmware you want to upgrade. OR click Select  
All to check all checkboxes.  
Figure 35 Paragon Update – Check All  
6. Click Load Hex File. The Open dialog appears.  
7. Navigate to where the desired firmware file (*.hex) is located, select it and click Open.  
8. (Optional) Click Check Device Information and then Yes to verify whether the firmware  
version is designed for the Paragon model you are going to upgrade. The Paragon Device  
and File Version Information window appears; click OK to exit. If the firmware file is  
suitable for updating your device, you will be returned to Paragon Update dialog. Otherwise,  
a warning message is displayed.  
Figure 36 Paragon Device and File Version Information Window  
 
CHAPTER 2: OPERATION  
37  
Figure 37 Wrong Firmware Warning Message  
9. Click Send To Paragon to perform the upgrade. A progress indicator is displayed on the  
bottom of the dialog to indicate the upgrade status. This may last for several minutes  
depending on your network speed.  
Figure 38 Paragon Update Progress Bar  
Paragon Update utility will update the selected devices one by one, but if one device encounters  
problems during updating, the utility will prompt you with a message, and you must click OK to  
let the utility continue to update the next devices.  
When the device is updated successfully, the “Device Update Successful” message box appears.  
Click OK to close the message.  
Figure 39 Paragon Update Successful Message  
Reorganizing the Update List  
You can remove unnecessary Paragon switches or user stations from the list in the Paragon  
Update dialog.  
1. Select the checkboxes of those Paragon switches or user stations that you want to remove.  
2. Click Delete.  
3. Click Save to save the changes.  
Disconnection  
Do this if you want to disconnect the existing connection session without closing Paragon  
Manager.  
1. Choose Session > Disconnect. Or click the Disconnect shortcut button on the toolbar.  
   
38  
PARAGON MANAGER USER GUIDE  
Figure 40 Session Menu - Disconnect  
2. Click Yes when a message asks you to confirm the disconnection.  
Closing Paragon Manager  
Choose Session > Exit to close Paragon Manager. The existing connection session is also  
disconnected at the same time.  
Synchronizing Database  
Paragon Manager is able to synchronize its database with the connected Paragon switch all the  
time after establishing the connection. Therefore, usually you don’t need to issue the  
“Synchronize Database” command manually. However, if the Paragon switch is disconnected  
abnormally by accident, and the database is not synchronized after the connection is restored, you  
may have to execute “Synchronize Database” to have Paragon Manager download the latest  
database from the Paragon system. The command can be executed either by choosing Setup >  
Synchronize Database or clicking the Synchronize Database icon on the toolbar.  
Figure 41 Setup Menu – Synchronize Database  
Paragon Manager Help  
•
•
Choose Help > Index to view this user manual online.  
Choose Help > About Paragon Manager to view product name and version information.  
This will assist you in the event you must call Raritan Technical Support for assistance.  
   
APPENDIX A: CLIENT SOFTWARE FOR PARAGON II SYSTEM CONTROLLER  
39  
Appendix A: Client Software for Paragon II  
System Controller  
This appendix is only for Administrators who use Paragon II System Controller (P2SC).  
The client software for Paragon II System Controller (P2SC), which is called Paragon II System  
Controller Admin (P2SC Admin), looks similar to Paragon Manager. Both software utilities  
share basic features and similar user interface. In this section, we will point out the common  
commands and differences. For other configuration information about Paragon II System  
Controller, see Paragon II System Controller (P2SC) User Guide, which can be downloaded  
from Raritan’s website (http://www.raritan.com).  
Comparison of Menu Commands  
between Paragon Manager and P2SC Admin  
Legend  
Shared commands  
Commands available in Paragon  
Manager only  
Commands available in P2SC Admin  
only  
   
40  
PARAGON MANAGER USER GUIDE  
For most of the shared commands, the operation and functions are the same as those in Paragon  
Manager and you can refer to previous chapters for these functions.  
As for the commands specific to P2SC Admin, they described in the following sections. For more  
information, see Paragon II System Controller (P2SC) User Guide.  
Some Differences in the Shared Commands  
Although most of the shared commands provide the same features and options as those in  
Paragon Manager, still a few differences exist in several shared commands.  
Connect (Session Menu)  
In P2SC, this command is for logging in to a Paragon II System Controller (P2SC). Simply type  
the Administrator’s user name (default: Admin) and password (default: raritan), and then click  
Login. Note the password is case-sensitive.  
Figure 42 P2SC - System Controller Admin Login Dialog  
 
APPENDIX A: CLIENT SOFTWARE FOR PARAGON II SYSTEM CONTROLLER  
41  
Create and Property (Users Menu)  
The functions of the “Create” and “Property” commands are similar to those of Paragon Manager.  
Only two points are different:  
•
P2SC does not support the Forced Video function so the configuration of “Allow Forced  
Video Privileges” is not available.  
•
“Green Mode” performs power-saving function as the “Sleep Mode” in Paragon Manager,  
but in P2SC it offers only two options: ON and OFF, instead of three options as Paragon  
Manager.  
−
ON will activate the power-saving mode when the mouse/keyboard activity is idle for the  
time (minutes) specified under “Green Mode.”  
−
Choosing OFF will never activate the power-saving mode.  
Figure 43 P2SC – Add User Dialog  
Exclusive Features in P2SC  
Those features specific to P2SC Admin are described below.  
RFT_Update (Setup Menu)  
The “RFT_Update” command updates the P2SC firmware. Before updating the firmware, you  
must download the latest P2SC firmware from the Firmware and Documentation webpage on  
Raritan’s website at: http://www.raritan.com/support/firmware-and-documentation/. Then do the  
following:  
1. Choose RFT_Update from the Setup drop-down menu.  
2. A message box appears, asking you to confirm the RFT update action. Click Yes.  
3. The Select RFP File dialog appears. Choose the appropriate file and click Open.  
Base UMT’s (Setup Menu)  
This command is to determine which and how many Paragon switches are managed by P2SC. A  
P2SC can control up to 8 Paragon II Base Units.  
 
42  
PARAGON MANAGER USER GUIDE  
Adding Paragon Switches in P2SC  
1. Select Base UMT’s from the Setup drop-down menu. The Paragon System Configuration  
dialog appears.  
Figure 44 P2SC – Paragon System Configuration Dialog (No Data)  
2. Click New to add new Paragon switches’ data.  
3. Click each field and type the appropriate data for Paragon switch intended to connect. Make  
sure the IP address and Port number for each Paragon switch are entered, and their data is the  
same as each Paragon switch’s network setting on the OSUI.  
Figure 45 P2SC – Paragon System Configuration Dialog (with Data)  
4. Click OK to put the Paragon switches under the control of P2SC, or Cancel to abort it.  
Removing Paragon Switches from P2SC  
1. Select Base UMT’s from the Setup drop-down menu. The Paragon System Configuration  
dialog appears.  
2. Click the Paragon switch which you want to remove and click Delete.  
About Paragon II System Controller Admin  
This command simply displays the current versions of the P2SC device and P2SC Admin  
software.  
 
APPENDIX A: CLIENT SOFTWARE FOR PARAGON II SYSTEM CONTROLLER  
43  
U.S./Canada/Latin America  
Monday - Friday  
Europe  
8 a.m. - 8 p.m. ET  
Europe  
Phone: 800-724-8090 or 732-764-8886  
For CommandCenter NOC: Press 6, then Press 1  
For CommandCenter Secure Gateway: Press 6, then Press 2  
Fax: 732-764-8887  
Monday - Friday  
8:30 a.m. - 5 p.m. GMT+1 CET  
Phone: +31-10-2844040  
Email: [email protected]  
Email for CommandCenter NOC: [email protected]  
Email for all other products: [email protected]  
United Kingdom  
Monday - Friday  
8:30 a.m. to 5 p.m. GMT  
Phone +44(0)20-7090-1390  
China  
Beijing  
France  
Monday - Friday  
Monday - Friday  
9 a.m. - 6 p.m. local time  
Phone: +86-10-88091890  
8:30 a.m. - 5 p.m. GMT+1 CET  
Phone: +33-1-47-56-20-39  
Shanghai  
Germany  
Monday - Friday  
Monday - Friday  
9 a.m. - 6 p.m. local time  
Phone: +86-21-5425-2499  
8:30 a.m. - 5 p.m. GMT+1 CET  
Phone: +49-20-17-47-98-0  
GuangZhou  
Korea  
Monday - Friday  
9 a.m. - 6 p.m. local time  
Phone: +86-20-8755-5561  
Monday - Friday  
9 a.m. - 6 p.m. local time  
Phone: +82-2-5578730  
India  
Melbourne, Australia  
Monday - Friday  
9 a.m. - 6 p.m. local time  
Phone: +91-124-410-7881  
Monday - Friday  
9:00 a.m. - 6 p.m. local time  
Phone: +61-3-9866-6887  
Japan  
Taiwan  
Monday - Friday  
9:30 a.m. - 5:30 p.m. local time  
Phone: +81-3-3523-5994  
Email: [email protected]  
Monday - Friday  
9 a.m. - 6 p.m. GMT -5 Standard -4 Daylight  
Phone: +886-2-8919-1333  
Email: [email protected]  

Pioneer GM 6200F User Manual
Pioneer BDP 52FD User Manual
Pioneer AVIC F900BT User Manual
Pentax Camera Flash AF 16 User Manual
Panasonic HDC SD9P User Manual
Olympus 262916 User Manual
Olympus 227615 User Manual
Motorola MOTOSTART H500 User Manual
Legacy Car Audio L7M User Manual
Korg MMA130 User Manual