Polycom IPOWER 70 User Manual

Installing the  
iPower70  
Room Camera  
Installing the  
iPower 70  
Room Camera  
This booklet describes how to install the iPower® 70 room camera.  
The iPower 70 is a pan-tilt-zoom (PTZ) camera that is used with a  
iPower collaboration system as a main or an auxiliary camera.  
About this  
Booklet  
This booklet contains information on:  
Before you install (page 4)  
Unpacking the box (page 5)  
Important note (page 6)  
Attaching the camera to a monitor (page 7)  
Connecting the camera cable to the collaboration  
system (page 8)  
Connecting an additional power cable (page 9)  
Service and support (page 10)  
Specifications (page 10)  
Refer to the collaboration system documentation for instructions on  
how to use this camera.  
3
INSTALLING THE IPOWER 70 ROOM CAMERA  
Before Installing  
Warning  
Before you begin this procedure, make sure you turn off  
your collaboration system’s power switch.  
To install this camera, you will need:  
8
a
The 8-pin camera cable (labeled with the  
icon on both  
cable collars) that came with your collaboration system, the  
WorldCart™, or the Premier Cart. (A camera cable is not  
supplied with this camera.)  
One of the following systems:  
• iPower 900 system, software version 1.0 or higher  
• Concorde•4500™ system, software version 6.50 or higher  
Venue•2000™ system, software version 1.3.50 or higher  
A pencil  
A flashlight (optional)  
a
4
 
Unpacking the Box  
To remove the camera from the box:  
Unpacking the  
Box  
1. With two hands, grasp the outside edges of the packing material  
and gently lift the unit from the box.  
2. Carefully remove the camera from the packing material and place  
it on a flat surface.  
Caution  
When lifting the iPower 70 camera, always lift the unit by its  
Note: Before you continue with the installation of the camera,  
please read the next section, “Important Note About  
Moving the Camera.”  
5
 
INSTALLING THE IPOWER 70 ROOM CAMERA  
The iPower 70 camera is designed to be controlled (moved) from the  
Important Note  
AboutMovingthe  
Camera  
collaboration system wireless keypad, the keyboard, or the remote  
control. Be sure that your system is turned on before you move the  
camera.  
You should not manually move the camera from side to side (pan)  
or up and down (tilt).  
If you manually move the iPower 70 camera head, you may  
experience unexpected camera pointing behavior when you use  
camera presets.  
To correct this condition, use the wireless keypad or the remote  
control to do the following:  
1. Press and hold the near-end right arrow button until the camera  
rotates as far right as it can.  
2. Press and hold the near-end left arrow button until the camera  
rotates as far left as it can.  
3. Press and hold the near-end up arrow button until the camera  
moves up as far as it can.  
4. Press and hold the near-end down arrow button until the camera  
moves down as far as it can.  
If the condition persists,  
Power the collaboration system off and then on again.  
6
 
Attaching the Camera to a Monitor  
Note: If you are installing a second monitor for a iPower 900  
system, be sure to install the iPower 70 camera on the  
NTSC or PAL monitor and not on the VGA monitor. If  
you are installing a second monitor for a Concorde•4500  
or Venue•2000 system, be sure to install the iPower 70  
camera on the main monitor and not on the graphics  
monitor.  
Attaching the  
Camera to a  
Monitor  
To attach the camera to the monitor:  
1. Clean the top of the monitor using a dry cloth. This helps the  
®
adhesive on the bottom of the Velcro to adhere securely.  
2. Without removing the backing from the adhesive strips, position  
the camera on the top center of the monitor with the front base of  
the camera within 0.75 inch (2 centimeters) of the front of the  
a
monitor  
.
3. With a pencil, mark the top of the monitor to indicate exactly where  
you will be attaching the camera.  
4. Remove the camera from the monitor and peel off the adhesive  
backing from the Velcro strips.  
5. Align the camera with the marks you made and firmly press it onto  
the top of the monitor.  
a
7
 
INSTALLING THE IPOWER 70 ROOM CAMERA  
Connecting the  
Camera Cable  
Caution  
Whenever you plug a cable into this camera, hold the  
camera by its base, not by the camera head.  
To connect the camera cable:  
a
8
1. Plug the 8-pin camera cable  
(labeled with the  
icon on both  
on the back of  
b
cable collars) into the 8-pin camera connector  
the camera.  
8
2. Locate the desired camera connector (labeled with the  
icon) on  
the back of the collaboration system computer box or electronics  
A
c
module . (Choose  
for main camera or  
for auxiliary  
camera.)  
3. Plug the other end of the camera cable into the desired camera  
c
connector  
.
b
a
c
8
8
8
 
Connecting an Additional Power Cable  
Although the camera cable provides power to the iPower 70 camera,  
if you are using a camera cable longer than 32.8 feet (10 meters), you  
must use an additional power cable for the camera.  
Connecting an  
Additional Power  
Cable  
To connect an additional power cable:  
1. Plug the additional power cable into the power connector on the  
a
back of the camera  
.
2. Plug the other end of this cable into an appropriate power source.  
If you are in the process of installing an entire collaboration system,  
you may now return to your collaboration system installation  
instructions.  
If you are mounting this camera on a tripod, refer to the mounting  
instructions included with your tripod mounting kit.  
a
9
 
INSTALLING THE IPOWER 70 ROOM CAMERA  
For support or service, please contact your Polycom service  
Service and  
Support  
provider or call Polycom Technical Support. You can find phone  
numbers for Technical Support in your area at the Polycom web site,  
Specifications  
Physical Specifications  
Dimensions:  
Length: 7.2 in. (18.3 cm)  
Width: 7 in. (17.8 cm)  
Height: 5.4 in. (13.7 cm )  
3.5 lb. (1.6 kg)  
Weight:  
Operating and Nonoperating Environments  
Temperature: Operating: 32° to 104° F (0° to 40° C)  
Nonoperating: -40° to 158° F (-40° to 70° C)  
Humidity:  
Operating: 15% to 75% (Noncondensing)  
Nonoperating: 0% to 90% (Noncondensing)  
Operating Specifications  
Field of View:  
Pan Range:  
Tilt Range:  
Zoom:  
66°  
100°  
+15°/-30°  
12x, autofocus  
Resolution:  
410,000 pixel, 0.25 in. (6 mm) CCD,  
430 HTVL  
Video Standard:  
Power:  
NTSC or PAL  
+12V DC  
10  
   

RCA EZ 105 User Manual
Peavey Electronics Car Speaker 3000 User Manual
Panasonic CQ VD7500U User Manual
Oster 6850 6889 User Manual
Newcon Optik NVS 7 8X User Manual
Mitutoyo Caller ID Box LSM 6200 User Manual
MB QUART Q LINE QSC 213 User Manual
Kenwood KFC HQW258 User Manual
Kenwood KDC 419 User Manual
JVC KD AR270 User Manual