Pioneer Elite BDP 94HD User Manual

Operating Instructions

Blu-ray Disc PLAYER

CAUTION

The following caution label appears on your unit.

Location: inside of the unit

This product is a class 1 laser product, but this

product contains a laser diode higher than Class 1.

To ensure continued safety, do not remove any covers

or attempt to gain access to the inside of the product.

Refer all servicing to qualified personnel.

D3-4-2-1-8_B_En

WARNING

Operating Environment

Operating environment temperature and humidity:

+5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH

(cooling vents not blocked)

To prevent a fire hazard, do not place any naked

flame sources (such as a lighted candle) on the

equipment.

D3-4-2-1-7a_A_En

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c_A_En

WARNING

This equipment is not waterproof. To prevent a fire

or shock hazard, do not place any container filed

with liquid near this equipment (such as a vase or

flower pot) or expose it to dripping, splashing, rain

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat

radiation (at least 10 cm at top, 10 cm at rear, and

10 cm at each side).

or moisture.

D3-4-2-1-3_A_En

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the

product, and to protect it from overheating. To

prevent fire hazard, the openings should never be

blocked or covered with items (such as newspapers,

table-cloths, curtains) or by operating the

Before plugging in for the first time, read the following

section carefully.

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

equipment on thick carpet or a bed.

D3-4-2-1-7b_A_En

or 120 V) written on the rear panel.

D3-4-2-1-4_A_En

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which

requires repair will be charged for even during the

warranty period.

K041_En

POWER-CORD CAUTION

The equipment should be disconnected by removing

the mains plug from the wall socket when left

unused for a long period of time (for example, when

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. If you find it damaged,

contact the Pioneer service center on the back cover, or

your dealer for a replacement.

on vacation).

D3-4-2-2-1a_A_En

CAUTION

The ꢀ STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from

the AC outlet to shut down all power. Therefore,

make sure the unit has been installed so that the

power cord can be easily unplugged from the AC

outlet in case of an accident. To avoid fire hazard,

the power cord should also be unplugged from the

AC outlet when left unused for a long period of time

This product incorporates copyright protection

technology that is protected by method claims of

certain U.S. patents and other intellectual property

rights owned by Macrovision Corporation and other

rights owners. Use of this copyright protection

technology must be authorized by Macrovision

Corporation, and is intended for home and other

limited viewing uses only unless otherwise authorized

by Macrovision Corporation. Reverse engineering or

disassembly is prohibited.

(for example, when on vacation).

D3-4-2-2-2a_A_En

WARNING: Handling the cord on this product or

cords associated with accessories sold with the

product will expose you to chemicals listed on

proposition 65 known to the State of California and

other governmental entities to cause cancer and

birth defect or other reproductive harm.

Wash hands after handling

D36-P4_A_En

This product contains mercury. Disposal of this

material may be regulated due to environmental

considerations. For disposal or recycling information,

please contact your local authorities or the Electronics

Industries Alliance : www.eiae.org.

K057_En

C67-7-3_En

We Want You Listening For A Lifetime

Since hearing damage from loud noise is often

undetectable until it is too late, this manufacturer

and the Electronic Industries Association’s

Consumer Electronics Group recommend you avoid

prolonged exposure to excessive noise. This list of

sound levels is included for your protection.

Selecting fine audio equipment such as the unit

you’ve just purchased is only the start of your

musical enjoyment. Now it’s time to consider how

you can maximize the fun and excitement your

equipment offers. This manufacturer and the

Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of

your equipment by playing it at a safe level. One that

lets the sound come through loud and clear without

annoying blaring or distortion-and, most importantly,

without affecting your sensitive hearing.

Decibel

Level Example

30 Quiet library, soft whispers

40 Living room, refrigerator, bedroom away from traffic

50 Light traffic, normal conversation, quiet office

60 Air conditioner at 20 feet, sewing machine

70 Vacuum cleaner, hair dryer, noisy restaurant

80 Average city traffic, garbage disposals, alarm clock

at two feet.

Sound can be deceiving. Over time your hearing

“comfort level” adapts to higher volumes of sound.

So what sounds “normal” can actually be loud and

harmful to your hearing. Guard against this by

setting your equipment at a safe level BEFORE your

hearing adapts.

THE FOLLOWING NOISES CAN BE DANGEROUS

UNDER CONSTANT EXPOSURE

90 Subway, motorcycle, truck traffic, lawn mower

100 Garbage truck, chain saw, pneumatic drill

120 Rock band concert in front of speakers,

thunderclap

140 Gunshot blast, jet plane

180 Rocket launching pad

To establish a safe level:

• Start your volume control at a low setting.

• Slowly increase the sound until you can hear it

comfortably and clearly, and without distortion.

Information courtesy of the Deafness Research Foundation.

Once you have established a comfortable sound

level:

• Set the dial and leave it there.

Taking a minute to do this now will help to prevent

hearing damage or loss in the future. After all, we

want you listening for a lifetime.

S001_En

Contents

01 Before you start

05 Using the Disc Navigator

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Putting the batteries in the remote control. . . . . . . . . . . . . . . . . . 8

Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Disc/content format playback compatibility . . . . . . . . . . . . . . . . . 8

File compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Titles and chapters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

DVD-Video regions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

BD-ROM regions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Movie Navigator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Photo Navigator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Music Navigator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

06 Using the Home Media Gallery

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

About network playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Using the Home Media Gallery . . . . . . . . . . . . . . . . . . . . . . . . . .33

Movie Navigator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Photo Navigator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Music Navigator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

About Windows Media Connect . . . . . . . . . . . . . . . . . . . . . . . . .38

02 Connecting up

Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Easy connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Using other types of video output. . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting for HDMI output . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting using the component video output . . . . . . . . . . . . . 14

Changing the output video resolution . . . . . . . . . . . . . . . . . . . . 14

Connecting using an S-Video output . . . . . . . . . . . . . . . . . . . . . 15

Connecting for surround sound . . . . . . . . . . . . . . . . . . . . . . . . . 15

Network connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Controlling this player via another Pioneer component . . . . . . . 16

Using an external IR receiver with this player. . . . . . . . . . . . . . . 16

07 Video/Audio Adjust menu

Video Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Audio Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

08 Initial Setup menu

Using the Initial Setup menu. . . . . . . . . . . . . . . . . . . . . . . . . . . .41

About the audio output settings . . . . . . . . . . . . . . . . . . . . . . . . .44

Speaker Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

03 Controls and displays

Front panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Front panel display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

09 Additional information

Taking care of your player and discs . . . . . . . . . . . . . . . . . . . . . .46

Screen sizes and disc formats. . . . . . . . . . . . . . . . . . . . . . . . . . .47

Resetting the player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Setting up the remote to control your TV . . . . . . . . . . . . . . . . . . .48

TV Preset code list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

BD/DVD language code list. . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

BD/DVD country/area code list . . . . . . . . . . . . . . . . . . . . . . . . . .49

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

04 Getting Started

Switching on and setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Using the on-screen displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Setting up for network use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Playing movies, music and photos. . . . . . . . . . . . . . . . . . . . . . . 22

Playing BD/DVD movies and audio CD . . . . . . . . . . . . . . . . . . . 22

Playback controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Frequently Asked Questions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Before you start

Chapter 1

Before you start

Features

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or

registered trademarks of HDMI Licensing LLC.

BD-ROM playback

Blu-ray Disc is a next-generation video disc format featuring far

higher disc capacity than conventional DVD. The higher capacity

makes a whole range of new and enhanced features possible, such

as support for high-definition video up to 1920 x 1080 pixels, high

quality, surround sound audio, greater interactivity and richer

content.

HDMI Control

By connecting this unit to a Pioneer plasma television or AV system

(amplifier or AV receiver etc.) with an HDMI cable, you can control

this unit from the connected plasma television or AV system, as well

as have the connected plasma television or AV system automatically

change inputs in response to this unit starting playback or having

the GUI screen (ex. Disc Navigator) displayed (known as the Auto-

select function). The connected plasma television can there by have

its power turned from off to on by this function.

BD-ROM discs are commercially produced discs (Video Distribution

format) that can contain movie and other video content, interactive

content, enhanced menu features such as pop-up menus (press

POPUP MENU/MENU during playback for these), full-color, high-

definition animated buttons and animated menu transition effects,

button sounds (sounds are played when menu buttons are selected

or activated), high-definition bitmap subtitles supporting full-color

images with frame-accurate animation effects up to full video frame

rate, and so on.

You can also have this unit turn on automatically when you control

this unit from a connected plasma television is turned on

(Simultaneous power function).

Additionally, when the language information from a connected

plasma television is received, you can have this unit’s on-screen

display language change automatically to that of the plasma

television (only when playback is stopped and GUI screen is not

displayed).

While BD capacity is enough for most applications, the BD-ROM

standard allows for content to be spread across several discs,

removing the limit of one physical disc. Follow the on-screen

instructions during playback when using these special kinds of

discs.

Refer to your plasma television’s operating manual for more

information regarding how your plasma television transmits

language information.

BD-J application

For more information about which operations can be carried out by

connecting via HDMI cable, refer to the operating manual for your

plasma television or AV system.

PureCinema

When you playback film material (24 frames/second) on a BD-ROM

or DVD-video disc, the progressive scan line automatically converts

the film material to optimum quality (see PureCinema on page 39).

1080/60p and 1080/24p output video

This player supports a variety of output video resolutions, up to

1080 lines/60 frames per second, progressive (HDMI only), making

it ideal for playing high-definition Blu-ray Discs.

The BD-ROM specification supports Java for interactive content.

The Java specification for BD-ROM is known as BD-J. This allows

content providers to put games and other interactive material linked

to specific titles on to BD-ROM discs. (This player does not support

downloadable BD-J content, direct connection to the Internet or the

retrieval of content through the Internet.)

High quality audio

Java and all Java-based trademarks and logos are trademarks or registered

trademarks of Sun Microsystems, Inc. in the U.S. and other countries.

Esmertec and Jbed are trademarks and/or registered trademarks of Esmertec AG.

Blu-ray supports DTS, DTS-HD (DTS-HD is played back as DTS),

Dolby Digital, Dolby Digital Plus, Dolby TrueHD (Dolby TrueHD is

played back as Dolby Digital) and Linear PCM audio in up to eight

channels (up to two channels for 24-bit/192 kHz audio). Connect this

player to a surround-sound AV receiver for a true home theater

experience.

Connect to a local area network

Connect this player to one or more computers in your house via

Ethernet and use them as media servers, streaming audio, video

and still image files for playback on your TV and/or audio system.

HDMI digital interface

The HDMI (High-Definition Multimedia Interface) interconnect

provides high quality digital audio and video, all from a single user-

friendly connector. HDMI is the first consumer electronics interface

to support uncompressed standard, enhanced, or high-definition

video plus standard to multi-channel surround sound audio, all

using one interface. You can easily connect to an HDMI-equipped

AV receiver or audio-visual device for high quality audio and video.

• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D

symbol are trademarks of Dolby Laboratories.

• “DTS” and “DTS Digital Surround” are registered trademarks of DTS, Inc.

Before you start

Movie file playback

WARNING

Video files encoded in the WMV (Windows Media* Video), MPEG-1/2

formats are playable from DVD-R/-RW, or from a connected media

server.

Do not use or store batteries in direct sunlight or

other excessively hot place, such as inside a car or

near a heater. This can cause batteries to leak,

overheat, explode or catch fire. It can also reduce the

Music file playback

life or performance of batteries.

D3-4-2-3-3_En

This player supports various audio formats, including WMA

(Windows Media* Audio), MP3 and WAV. You can play files stored

on DVD-R/-RW, or from a connected media server.

Using the remote control

Photo file playback

Please keep in mind the following when using the remote control:

PNG, GIF and JPEG image files — including the popular EXIF format

used by most digital cameras to store picture shooting information

together with the JPEG image — are playable from DVD-R/-RW, or

from a connected media server.

• Make sure that there are no obstacles between the remote and

the remote sensor on the unit.

• The remote has a range of about 23 feet (at an angle of 30º from

either side of the sensor). Use within this range in front of the

remote control sensor on the front panel.

* “Windows Media™” is a trademark of Microsoft Corporation.

• Remote operation may become unreliable if strong sunlight or

fluorescent light is shining on the unit’s remote sensor.

This product includes technology owned by Microsoft Corporation and cannot be

used or distributed without a license from Microsoft Licensing, Inc.

• Remote controllers for different devices can interfere with each

other. Avoid using remotes for other equipment located close to

this unit.

What’s in the box

• Replace the batteries when you notice a fall off in the operating

range of the remote.

Please confirm that the following accessories are in the box along

with these operating instructions when you open it:

• When the batteries run down or you change the batteries, the TV

preset codes are automatically reset. See Resetting the player on

page 47 to reset them.

• Remote control

• AA/R6P dry cell batteries x2

• Stereo audio cable (red/white plugs)

• Video cable (yellow plugs)

• LAN cable

Disc/content format playback

compatibility

• Power cable

• Warranty card

General disc compatibility

This player is compatible with a range of disc types (media) and

formats. Compatible discs will usually feature one of the following

logos on the disc and/or disc packaging. Note however that some

disc types, such as recordable BD, DVD or CD, may be in an

unplayable format — see below for further compatibility

information.

Putting the batteries in the remote

control

•

Insert two AA/R6P batteries into the battery compartment

following the indications (,) inside the compartment.

Blu-ray Disc (BD)

DVD-Video

DVD-R

DVD-R DL

DVD-RW

Important

Incorrect use of batteries can result in hazards such as leakage and

bursting. Please observe the following:

• Don’t mix new and old batteries together.

• Don’t use different kinds of batteries together — although they

may look similar, different batteries may have different voltages.

• “Blu-ray Disc” and

are trademarks.

• Make sure that the plus and minus ends of each battery match

the indications in the battery compartment.

•

is a trademark of DVD Format/Logo Licensing Corporation.

• This player may not be able to play perfectly every disc that

features one of the logos listed above. Please contact Pioneer if

you find a disc that won’t play properly.

• Remove batteries from equipment that isn’t going to be used for

a month or more.

• When disposing of used batteries, please comply with

governmental regulations or environmental public instruction’s

rules that apply in your country/area.

Before you start

File compatibility

Important

• Compatible media: DVD-R, DVD-RW, media server on network

(some formats may not be supported depending on the media

server type).

• This player is not compatible with BD-R/-RE (Blu-ray Disc

Recordable Format Ver. 1 and Blu-ray Disc Recordable Format

Ver. 2), DVD-R/-RW (VR mode), DVD-Audio, DVD-RAM, CDs

(with PC files) or disc types other than those listed above.

• Even when they are in a supported format, some files may not

play or display depending on the content.

• Do not use 8 cm disc adapters with this player. 8 cm discs can

be played directly by placing then in the 8 cm disc depression in

the center of the disc tray.

• Even when playing a supported format, some functions may not

operate properly depending on the content.

• DRM-protected contents on DVD-R/-RW discs or on media

servers that do not support WMDRM, and otherwise

incompatible files are skipped.

BD-ROM compatibility

• BD-ROM discs should conform to the BD-ROM Profile1.

• Please note, the following file naming structure needs to be

adhered to when creating/renaming any digital media to be

played on the unit (either through computer-created disc media,

or the Home Media Gallery connection). This disclaimer does

not apply to any media purchased at retail locations:

Due to the coding system used, this player will only read/play

files named using standard alphanumeric characters. Any other

characters or symbols (e.g. characters with accents) used in

naming the file will render it unreadable/unplayable by the unit.

If you encounter any difficulties with playback of media, please

rename the file in accordance to this standard.

• If a disc containing DTS-HD audio is played, this player is only

compatible with bitstream output or playback decoding of

current DVD (DTS) material (sampling rate: 48 kHz max., 5.1ch).

• If a disc containing Dolby TrueHD audio is played, this player is

only compatible with bitstream output or playback decoding of

current DVD (Dolby Digital) material (sampling rate: 48 kHz

max., 5.1ch).

• This player cannot play 8 cm BD-ROM discs.

DVD-R/-RW compatibility

• This player is compatible with DVD-R/-RW discs recorded in

DVD-Video format.

Supported video formats

• DVD-R/-RW discs containing PC data can also be played. See

below for file compatibility.

•

Windows Media Video 9 (WMV9)

– MP@HL

• Unfinalized DVD-R/-RW discs and VR mode DVD-R/-RW discs

cannot be played in this player.

Windows Media Video 9 (WMV9) Advanced Profile (VC-1)

– AP@L3

MPEG-2 (PS/TS)

– MP@HL

PC-created disc compatibility

Discs recorded using a personal computer may not be playable in

this unit due to the settings of the application software used to

create the disc. Check with the software publisher for more detailed

information.

MPEG-1

Supported audio formats

CD-R/-RW/-ROM compatibility

• This player does not support the playback of CD-R/-RW discs.

•

Windows Media Audio 9 (WMA9)

– Bit rate:up to 192 kbps (constant bit-rate (CBR));

up to 384 kbps (variable bit-rate (VBR))

– Sampling rates: 44.1 kHz or 48 kHz

• PC files stored on CDs cannot be played back.

• CD-R/-RW discs that are not finalized cannot be played back.

•

Windows Media Audio 9 Pro (WMA9 PRO)

– Bit rate: up to 768 kbps

• Regarding copy protected CDs: This product is designed to

conform to the specifications of the audio CD format. This player

does not support the playback or function of discs that do not

conform to these specifications.

– Sampling rates: 44.1 kHz or 48 kHz

– Channels: up to 5.1ch

•

MPEG-1 Audio Layer 3 (MP3)

– Sampling rates: 32 kHz, 44.1 kHz or 48 kHz

– Bit rate: up to 320 kbps

DualDisc playback

A DualDisc is a new two -sided disc, one side of which contains DVD

content –video, audio, etc. –while the other side contains non-DVD

content such as digital audio material.

Linear PCM (WAVE)

– Sampling rates: 44.1 kHz or 48 kHz

The DVD side of a DualDisc will play in this product (excluding any

DVD-Audio content).

Supported image formats

The non-DVD, audio side of the disc is not compatible with this

player.

•

JPEG

It is possible that when loading or ejecting a DualDisc, the opposite

side to that being played will be scratched. Scratched discs may not

be playable.

– Baseline JPEG and progressive JPEG/Exif are supported

– Resolution: up to 4096 x 4096 pixels

•

PNG

For more detailed information on the DualDisc specification, please

refer to the disc manufacturer or disc retailer.

– Resolution: up to 4096 x 4096 pixels

GIF

– Resolution: up to 4096 x 4096 pixels

Before you start

File extensions

The following file extensions should be used with this player:

DVD-Video regions

All commercially produced DVD movies (DVD-Video discs) carry a

region mark on the case somewhere that indicates which region(s)

of the world the disc is compatible with. This player also has a region

mark, which you can find on the rear panel. Discs from incompatible

regions will not play in this player. Discs marked ALL will play in any

player.

•

Video

.wmv .mpg .mpeg

Audio

.wma .mp3 .wav

Image

.jpg .jpeg .png .gif

The diagram below shows the various DVD regions of the world.

Even when files have a supported file extension, some files may not

play or display depending on the content or media server type.

Titles and chapters

BD and DVD movie discs are divided into one or more titles. Titles

may be further subdivided into chapters.

This player is REGION 1.

Title 1

Title 2

Title 3

BD-ROM regions

Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 1 Chapter 2

Like DVD movies, BD movie discs (BD-ROM) also carry a region

mark that indicates which region(s) of the world the disc is

compatible with. This player also has a region mark, which you can

find on the rear panel. Discs from incompatible regions will not play

in this player. Discs marked ALL will play in any player.

The diagram below shows the various BD-ROM regions of the world.

REGION A

REGION B

REGION C

This player is REGION A.

Connecting up

^CC^ho^aptn^ern²ecting up

Rear panel

CONTROL

AUDIO OUT

(5.1ch)

AUDIO OUT

(2ch)

AC IN

CENTER SURROUND FRONT

VIDEO OUT

DIGITAL AUDIO OUT

SETTING

HDMI OUT

LAN(10/100)

IR RECEIVER

SUB WOOFER

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

10 11

AC IN

AUDIO OUT (5.1ch)

Connect the supplied power cord here, then plug into a power

outlet.

Multi-channel (5.1ch) analog audio outputs for connection to an AV

receiver with multi-channel analog audio inputs (page 15).

CONTROL IN

AUDIO OUT (2ch)

Use to control this player from the remote sensor of another Pioneer

component with a CONTROL OUT terminal and bearing the

mark. Connect the CONTROL OUT of the other component to the

CONTROL IN of this player using a mini-plug cord (page 16).

Stereo analog audio outputs for connection to your TV, AV receiver

or stereo system (page 12).

10 IR IN

Jack for an external IR (infrared) remote control receiver (page 16).

HDMI OUT

11 IR RECEIVER switch

Switch to the setting compatible with your external IR remote

control receiver (page 16).

HDMI output providing a high quality interface for digital audio and

video (page 13).

LAN (10/100)

Ethernet port for 10BASE-T (10 Mbps) or 100BASE-TX (100 Mbps)

network connection (page 16).

Tip

• When connecting this player to your TV, AV receiver or other

equipment, make sure that all components are switched off

and unplugged.

VIDEO OUT and S-VIDEO OUT

Video output (composite) that you can connect to your TV or AV

receiver using the supplied video cable (page 12).

• You may find it useful to have the manuals supplied with your

other components handy when connecting this player.

S-Video output that you can use instead of the VIDEO OUT jacks

(page 15).

COMPONENT VIDEO OUT

High quality video output for connection to a TV, monitor or AV

receiver that has component video inputs.

Connect using a commercially available three-way component video

cable (page 14).

DIGITAL AUDIO OUT – COAXIAL/OPTICAL

Digital audio outputs for connection to a PCM, Dolby Digital, and/or

DTS-compatible AV receiver (page 15).

Connecting up

Easy connections

AUDIO IN

VIDEO IN

CONTROL

VIDEO OUT

AUDIO OUT

(5.1ch)

AUDIO OUT

(2ch)

AC IN

CENTER SURROUND FRONT

VIDEO OUT

DIGITAL AUDIO OUT

SETTING

HDMI OUT

LAN(10/100)

IR RECEIVER

SUB WOOFER

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

AUDIO OUT

To power outlet

This is a basic setup that allows you to watch discs on your TV using

just the cables supplied.

Using other types of video output

This player has standard (composite), S-Video and component video

outputs, as well as an HDMI connector (for digital video/audio).

Important

In order to be able to watch HD (high definition) BDs at their full

resolution, you should connect the player to your TV using either the

component video output, or (even better) the HDMI output.

• This player is equipped with copy protection technology. Do not

connect this player to your TV via a VCR using AV cables, as the

picture from this player will not appear properly on your TV. (This

player may also not be compatible with some combination TV/

VCRs for the same reason; refer to the manufacturer for more

information.)

An HDMI connection will additionally give you HD output when

watching DVDs.

If your display has neither of these connection types, an S-Video jack

is also provided, which should give slightly better video quality than

using the standard video output.

• Do not unplug the player from the power outlet while it is

switched on.

• Do not plug this player into a switched power supply found on

some amplifiers and AV receivers.

Connect the VIDEO OUT and one pair of AUDIO OUT jacks

to a set of audio/video inputs on your TV.

Use the supplied red/white stereo audio and yellow video cables.

Make sure you match up the left and right audio outputs with their

corresponding inputs for correct stereo sound.

See Using other types of video output below if you want to use a

different type of connection.

Connect the supplied AC power cord to the AC IN inlet,

then plug into a power outlet.

Connecting up

•

Use an HDMI cable (not supplied) to connect the HDMI OUT

Connecting for HDMI output

interconnect on this player to an HDMI interconnect on an

HDMI-compatible display.

If you have an HDMI or DVI (with HDCP) equipped monitor or

display, you can connect it to this player using a commercially

available HDMI cable.

The HDMI connector outputs uncompressed digital video, as well as

most digital audio formats.

HDMI IN

Important

• This unit has been designed to be compliant with HDMI (High-

Definition Multimedia Interface). Depending on the component

you have connected, using a DVI connection may result in

unreliable signal transfers.

HDMI-compatible display

CONTROL

AUDIO OUT

(5.1ch)

AUDIO OUT

(2ch)

• If you change the display connected to the HDMI output, you will

also need to change the Output Video Resolution settings to

match the new display (see Changing the output video resolution

on page 14 to do this).

CENTER SURROUND FRONT

VIDEO OUT

DIGITAL AUDIO OUT

SETTING

HDMI OUT

LAN(10/100)

IR RECEIVER

SUB WOOFER

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

• The HDMI connection is compatible with 8-channel linear PCM

signals (44.1 kHz to 192 kHz , 16 bit/20 bit/24 bit), Dolby Digital

bitstream and DTS (5.1 channel signals) bitstream.

• The arrow on the cable connector body should be face up for

correct alignment with the connector on the player.

• Depending on the HDMI cable being used, 1080p output may

not appear correctly.

• If you connect a DVI device to the HDMI output of this player,

ensure that it is compliant with High-bandwidth Digital Content

Protection (HDCP). If you choose to connect to a DVI connector,

you will need a separate adaptor (DVIHDMI) to do so. A DVI

connection, however, does not support audio signals. Consult

your local audio dealer for more information.

After switching on the player you may need to set the output video

resolution and HDMI color space for compatibility with your display.

See Changing the output video resolution on page 14 and HDMI

Color Space in Using the Initial Setup menu on page 41.

About HDMI

HDMI supports both standard and high-definition video, plus

standard and multi-channel surround-sound audio. HDMI features

include uncompressed digital video, one connector (instead of

several cables and connectors), and communication between the

AV source and AV devices such as DTVs.

HDMI was developed to provide the technologies of High-bandwidth

Digital Content Protection (HDCP) as well as Digital Visual Interface

(DVI) in one specification. HDCP is used to protect digital content

transmitted and received by DVI-compliant displays.

About HDMI Control

You can enable HDMI Control by turning the HDMI Control setting

to On for all components connected via HDMI cable. Check the

video output from this unit once you have completed making

connections and settings for all components. You will need to check

the video output each time you change connected components or

remove the HDMI cable.

Note

1 192 kHz output is limited to 2 channels.

Connecting up

Connecting using the component

video output

Note

• Depending on your display, some of the settings may result in

the picture disappearing. In this case, press OUTPUT

RESOLUTION repeatedly until the picture re-appears.

You can use the component video output instead of the standard

video out jack to connect this player to your TV (or other equipment).

• 1080/60p and 1080/24p output is only compatible with HDMI

displays. They are not compatible with the component video

output.

•

Use a component video cable (not supplied) to connect the

COMPONENT VIDEO OUT jacks to a component video input on

your TV, monitor or AV receiver.

Be careful to match up the colors of the three jacks for correct

connection.

• When Output Video Resolution is set to 720p, 1080i or 1080p,

video is output in 16:9 format even if TV Aspect Ratio is set to 4:3

(Standard). See TV Aspect Ratio on page 41.

• If the contours of the displayed subjects look jagged or blurred,

try setting the Output Video Resolution to 480i. (If you connected

this player to your TV with the HDMI connection and the picture

disappears when you switch the Output Video Resolution to

480i, use the component connection with the 480i Output Video

Resolution or S-Video, the standard composite connection

instead.)

COMPONENT

VIDEO IN

• Note that when using a Component Video connection with a TV

or other AV component (not using HDMI), 480/60i video may be

output in 480/60p.

CONTROL

24p output

AUDIO OUT

(5.1ch)

AUDIO OUT

(2ch)

For smooth presentation of 1080/24p or 720/24p video with an

HDMI-equipped display compatible with 1080/24p input, set 24p

Direct Out on this player to On (see page 41).

CENTER SURROUND FRONT

VIDEO OUT

DIGITAL AUDIO OUT

SETTING

HDMI OUT

LAN(10/100)

IR RECEIVER

SUB WOOFER

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

This player will output 1080/24p video over HDMI in the following

cases:

• 1080/24p video: When the Output Video Resolution is set to

Auto or Source Direct.

• 720/24p video: When the Output Video Resolution is set to Auto.

Changing the output video resolution

Use the OUTPUT RESOLUTION button located on both the front

panel and the remote control to switch the output video resolution

for the HDMI and component video outputs.

Note

• Even when 24p Direct Out is set to On, if a TV not compatible with

1080/24p video is connected, the actual frame frequency of the

video output will be 60 Hz.

The table below shows the output settings.

Component

output

Video/S-Video

output

Setting HDMI output

• The video output will be interrupted when switching the video

output from 1080/24p or 720/24p to other output video

resolutions, or when switching to 1080/24p or 720/24p from

more on these connections.

Digital connections

CONTROL

•

Connect one of the DIGITAL AUDIO OUT jacks on this player

AUDIO OUT

(5.1ch)

AUDIO OUT

(2ch)

to a digital input on your AV receiver.

CENTER SURROUND FRONT

VIDEO OUT

DIGITAL AUDIO OUT

SETTING

HDMI OUT

LAN(10/100)

DIGITAL

AUDIO IN

IR RECEIVER

SUB WOOFER

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

COAXIAL

OPTICAL

AV receiver

CONTROL

AUDIO OUT

(5.1ch)

AUDIO OUT

(2ch)

CENTER SURROUND FRONT

VIDEO OUT

DIGITAL AUDIO OUT

SETTING

HDMI OUT

LAN(10/100)

IR RECEIVER

SUB WOOFER

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

Connecting up

Network connection

Controlling this player via another

Pioneer component

This player can be connected to a local area network (LAN) via the

Ethernet port on the rear panel.

The CONTROL IN jack allows you to control this player via the

remote control sensor of another Pioneer component — typically an

AV receiver — that has a CONTROL OUT jack. Remote control

signals are passed through to the player from the remote sensor of

the other component, allowing you greater freedom in the

placement of your player.

After making the physical connection the player needs to be set up

for network communication. This is done from the Initial Setup

menu — see Setting up for network use on page 21 for detailed

instructions.

For best performance, we recommend using a 100BASE-TX

compatible PC and Ethernet hub.

•

Use a miniplug cord (not supplied) to connect the CONTROL

IN jack of this player with the CONTROL OUT jack of your other

Pioneer component.

Connecting via an Ethernet hub

If you already operate one or more PCs on a local area network, you

can integrate this player by connecting it to the Ethernet hub using

the included LAN cable.

CONTROL

OUT

In the example configuration below, this player would be able to

access content from either of the PCs.

AV Receiver

CONTROL

AUDIO OUT

(5.1ch)

AUDIO OUT

(2ch)

AC IN

CENTER SURROUND FRONT

VIDEO OUT

CONTROL

DIGITAL AUDIO OUT

SETTING

HDMI OUT

LAN(10/100)

IR RECEIVER

SUB WOOFER

AUDIO OUT

(5.1ch)

AUDIO OUT

(2ch)

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

CENTER SURROUND FRONT

VIDEO OUT

DIGITAL AUDIO OUT

SETTING

HDMI OUT

LAN(10/100)

IR RECEIVER

SUB WOOFER

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

Ethernet hub

(router with hub functionality)

• You will also need to connect a coaxial digital cable, analog

audio cable, or video cable.

• When connected via System Control, point the remote control

toward the connected component (such as an AV receiver). The

remote will not work correctly when pointed at this unit.

LAN(10/100)

• You cannot connect use System Control with components that

do not have a System Control jack or with components

manufactured by companies other than Pioneer.

Using an external IR receiver with this

player

PC 1

PC 2

If you prefer to keep your AV equipment in a closed cabinet, you can

use an external IR receiver connected to the IR IN jack. You can thus

have just the receiver outside of the cabinet and still be able to

control the player.

Connecting directly to a PC

If you only need to use one PC to act as a media server, you can

connect this player directly to the PC using the included LAN cable.

CONTROL

AUDIO OUT

(5.1ch)

AUDIO OUT

(2ch)

AC IN

CENTER SURROUND FRONT

VIDEO OUT

DIGITAL AUDIO OUT

P^B

SETTING

HDMI OUT

LAN(10/100)

IR RECEIVER

SUB WOOFER

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

IR receiver

CONTROL

AUDIO OUT

(5.1ch)

AUDIO OUT

(2ch)

LAN(10/100)

CENTER SURROUND FRONT

VIDEO OUT

DIGITAL AUDIO OUT

P^B

SETTING

HDMI OUT

LAN(10/100)

IR RECEIVER

SUB WOOFER

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

Tip

• You may need to set the IR RECEIVER switch (located under the

IR IN jack) for this player to recognize the IR receiver correctly.

• This player does not supply power to the external IR receiver.

Please see the operating instructions of the IR receiver for the

power requirements.

Controls and displays

Chapter 3

Controls and displays

Front panel

 STANDBY/ON



Press to switch the player on (the power indicator and indicator in

the middle of the unit light up when the power is on) or into standby.

Press to start or resume playback.



Disc tray

Press to stop playback (you can resume playback by pressing ).

 OPEN/CLOSE



Press to open or close the disc tray.

Press to pause playback. Press again to restart.

Indicators

Skip/scan buttons

• FL OFF – Lights when the display and other indicators are

switched off.

•  – Press to jump to the next chapter, track, etc. Press

and hold for fast forward scanning.

• HD – Lights when the video output is 720p, 1080i or 1080p

(HDMI), or 720p or 1080i (component).

•  – Press to jump back to the beginning of the current

chapter, track, etc. then to previous chapters, tracks, etc. Press

and hold for fast reverse scanning.

• LAN – Lights when there is an active local area network (LAN)

connection.

10 OUTPUT RESOLUTION

• HDMI – Lights when a device is connected via HDMI.

Press to switch the output resolution over HDMI and component

video outputs. See Changing the output video resolution on page 14.

Display

Shows disc status and playback information.

Controls and displays

10 ANGLE

Remote control

Press to change the camera angle during BD-ROM or DVD-Video

movie multi-angle scene playback (see page 25).

11 DISC NAVIGATOR/TOP MENU

Press to display the top menu of a BD-ROM or DVD-Video disc.

When playing a DVD-R/-RW disc, press to display/exit the Disc

Navigator.

STANDBY/ON FL

DIMMER



OPEN/CLOSE



HOME MEDIA

GALLERY

12 POPUP MENU/MENU

BD-ROM: Press to display/hide the pop-up menu.

DVD-Video: Press to display the disc menu (if there is one).

13 /// and ENTER

Use to navigate on-screen displays and menus. Press ENTER to

select an option or execute a command.

CLEAR

AUDIO

ENTER

OUTPUT

RESOLUTION

SUBTITLE ANGLE

DISPLAY

14 HOME MENU

Press to display the player’s Home Menu, from which you can

access most of the player’s functions.

POPUP MENU

DISC NAVIGATOR

TOP MENU

ENTER

15 RETURN

Press to return to a previous screen.

HOME

RETURN

YELLOW

16 RED/GREEN/BLUE/YELOW

Use to navigate BD-ROM menus.

RED

GREEN

BLUE

17 Playback controls

/: Press to start reverse/forward scanning.

: Press to start or resume playback.

: Press to pause playback; press again to restart.

PLAY MODE

PHOTO ZOOM

VIDEO

ADJUST

TV CONTROL

: Press to stop playback (you can resume playback by

pressing ).



INPUT

SELECT

CHANNEL VOLUME

 : Press to jump to the start of the previous/next

chapter/track.

 /

page 24).

: Use for slow motion and step frame (see

BD PLAYER

18 PLAY MODE

Press to change the Play Mode (repeat play, for example) (see

page 24).

 STANDBY/ON

Press to switch the player on or into standby.

 OPEN/CLOSE

19 PHOTO ZOOM

Press to zoom the screen when displaying a still image (see

page 25).

Press to open or close the disc tray.

FL DIMMER

Press to change the brightness of the display. When the display and

other indicators are off, the FL OFF indicator (see page 17) lights.

20 VIDEO ADJUST

Press to display the Video Adjust screen (see page 39).

Number buttons

Use to enter title, chapter or track numbers, etc.

21 TV CONTROL buttons

See also Setting up the remote to control your TV on page 48.

CLEAR: Press to clear a numeric entry, etc.

ENTER: Press to select an option or execute a command.

HOME MEDIA GALLERY

: Press  to turn the TV on or into standby.

VOLUME +/–: Use to adjust the volume.

CHANNEL +/–: Use to select TV channel.

Press to display the Home Media Gallery screen (see page 32).

INPUT SELECT: Press to change the input function of the TV.

OUTPUT RESOLUTION

Press to switch the output resolution over HDMI and component

video outputs (see page 14 and page 25).

AUDIO

Press to select the audio channel or language (see page 25).

SUBTITLE

Press to select a subtitle display (see page 25).

DISPLAY

Press to display information (see page 25).

Controls and displays

Front panel display



Lights during playback of a disc.

Character display

Shows various playback information — disc time, chapter and title

number, etc.

Getting Started

Chapter 4

Getting Started

If you don’t want to use the Setup Navigator, press  to select

Switching on and setting up

Cancel, then press ENTER to exit the Setup Navigator.

When you switch the player on for the first time the Setup Navigator

screen appears. We recommend using this to make a few basic

player settings.

Use the / buttons to select the output video resolution

then press ENTER.

Setup Navigator

Output Video Resolution

STANDBY/ON

Auto

480i

ꢀ

ꢁ

480p

720p

1080i

1080p

Source Direct

If you connected this player to your TV using the HDMI connector,

select from Auto, 480i (interlaced), 480p (progressive), 720p,

1080i, 1080p, or Source Direct, then skip to step 7 (the aspect ratio

will automatically be set to 16:9 (Widescreen)). Generally, the Auto

setting is recommended.

Setup Navigator

ENTER

Output Video Resolution

S-Video/Video only

480i

480p

720p

Switch on your TV and set the video input to this player.

1080i

Don't Know

Press the  STANDBY/ON button on the remote control or

the front panel to switch on.

• It can take up to one minute for the unit to turn on.

If you’re using an S-Video or composite video connection, select

S-Video/Video only.

• When you switch on for the first time, your TV should display the

Setup Navigator screen. (If the Setup Navigator doesn’t appear,

you can also access it from the Initial Setup menu; see page 43).

If you’re using a component video connection, match the output

setting with the capabilities of your TV. Select from: 480i, 480p,

720p, 1080i or Don’t Know. If you select 720p or 1080i, skip the

next step since the aspect ratio will automatically be set to 16:9

(Widescreen).

• When you have this unit connected to a plasma television that is

compatible with HDMI Control, language settings are imported

from the plasma television’s OSD settings before Setup

Navigator begins.

Use the / buttons to select the aspect ratio of your TV

then press ENTER.

Use the / buttons to choose a language, then press

ENTER.

Setup Navigator

TV Aspect Ratio

Setup Navigator

16:9 (Widescreen)

4:3 (Standard)

Language

English

If you have a widescreen TV, select 16:9 (Widescreen); if you have a

standard size TV, select 4:3 (Standard).

français

Español

Select ‘Finish Setup’ to accept the settings and exit the

Setup Navigator, or ‘Go Back’ to go through the settings again.

Press ENTER to start setting up using the Setup Navigator.

Setup Navigator

Setup is complete!

Enjoy using your BD player!

Finish Setup

Before using, make some simple

settings for the BD player.

Go Back

Start

Cancel

You can run the Setup Navigator at any time by selecting it from the

Options menu — see page 43.

Please use the Initial Setup if you

want to make more detailed settings.

Getting Started

• Select DEL to delete the character at the current cursor position

in the name field.

About the screen saver

If the player is stopped or paused for more than five minutes with no

other operation, the screen saver starts.

• Select CLR to clear the name field.

Once the screen saver has started, pressing any button on the front

panel or remote will clear it and return the player to normal

operation.

Select ‘DONE’ to register the name and exit the input

screen.

Select CANCEL to close the keypad without registering the name.

The screen saver starts for CDs and music files after five minutes

pass without any commands input, whether or not playback has

been paused or stopped.

Select ‘IP Configuration’ then ‘Next Screen’ to display the IP

configuration screen.

Initial Setup

Using the on-screen displays

Video Out

Audio Out

Language

Parental Lock

Network

IP Configuration

This player makes extensive use of graphical on-screen displays

(OSDs). You should get used to the way these work as you’ll need to

use them when setting up the player, using some of the playback

features, and when making more advanced settings for audio and

video.

Auto set IP Address

Off

IP Address

192 255 255

Subnet mask

Default gateway

255 255 255

Speakers

Options

192 168

Set the IP address.

All the screens are navigated in basically the same way, using the

cursor buttons (///) to change the highlighted item and

pressing ENTER to select it.

Set ‘Auto set IP Address’ to ‘On’.

If there is a DHCP server on the local area network (LAN), this player

will automatically be allocated an IP address. If you’re using a

broadband router or broadband modem that has a DHCP (Dynamic

Host Configuration Protocol) server function, select On. The IP

address will automatically be determined.

Button

What it does

Display/exit the on-screen display

HOME MENU

   

ENTER

Changes the highlighted menu item

Selects the highlighted menu item

If there is no DHCP server on the network and you select On, this

player will use its own Auto IP function to determine the IP address.

• If you want to set the IP address manually, select Off then set

the IP Address, Subnet mask and Default gateway: Use the /

// buttons to select a field; use the number buttons to

enter a value. Press ENTER to finish and exit the screen.

Returns to the previous menu or screen without

saving changes

RETURN

Press HOME MENU to exit the Initial Setup menu.

Tip

You should now be able to use the Home Media Gallery (accessible

from the Home Menu). See Using the Home Media Gallery on

page 32 for more.

• Information at the bottom of an OSD screen explains the

currently selected menu item and shows which buttons can be

used for that screen.

• For information on DHCP refer to the network device’s operating

instructions.

• You may need to contact your service provider or network

administrator when manually entering an IP address.

Setting up for network use

If you’ve connected this player to a local area network (LAN) you may

need to make a few settings before you can use the Home Media

Gallery feature over the network.

Press HOME MENU and select ‘Initial Setup’.

Select ‘Network’.

Select ‘Device Name’ then ‘Next Screen’.

Use the on-screen keypad to enter a name for the player.

This is how the player will appear to connected devices on the local

area network.

Device

name input

BDP-94HD/KU/CA

SHFT

SPC

DEL

CLR

• Use the /// buttons and ENTER to select characters

from the keypad.

• Select SHFT to toggle between upper and lower case.

• Select SPC to insert a space.

Getting Started

When playing BD-ROM discs:

Playing movies, music and photos

• Commercially produced BD-ROM movie discs often go straight

to the disc menu when playback is started (sometimes preceded

by an opening sequence). Navigate through the disc menu

using the cursor keys (///) and the ENTER button. You

can also use the number buttons to select numbered items in

some menus.

Using this player, you can enjoy watching movies, listening to music

and browsing photos, from BD and DVD discs or from a media

server on the network. How you navigate, browse and play content

varies according to the format of the content and the media:

• To play a BD or DVD movie disc (i.e., one containing BD-ROM or

DVD-Video application format), see Playing BD/DVD movies and

audio CD below.

• To get back to the top menu, press TOP MENU.

• Some BD-ROM discs feature pop-up menus that do not

interrupt playback; press POPUP MENU/MENU to access

these.

• To play a DVD-R/-RW disc recorded with movie, music or photo

files, turn to Using the Disc Navigator on page 27.

• To play content from a media server, please refer to Using the

Home Media Gallery on page 32.

When playing DVD-Video discs:

• Commercially produced DVD movies often go straight to the

disc menu when playback is started (sometimes preceded by an

opening sequence). Navigate the disc menu using the cursor

(///) and ENTER buttons. You can also use the number

buttons to select numbered items in some menus.

Playing BD/DVD movies and audio CD

The basic playback controls for playing BD/DVD movies and audio

CD discs are covered here. Further functions are detailed in the next

chapter.

• To get back to the top menu, press TOP MENU.

• To get back to the disc menu, press POPUP MENU/MENU.

When playing audio CDs:

• For more information see Playback controls on page 23.

STANDBY/ON

OPEN/CLOSE

ꢀ

ꢁ

When you’ve finished using the player, eject the disc and

switch the player back into standby.

• To open/close the disc tray, press  OPEN/CLOSE. Remove the

disc before putting the player into standby.

• Press  STANDBY/ON to switch the player into standby.

POPUP MENU

TOP MENU

ENTER

If the player isn’t already on, press  STANDBY/ON to

switch it on.

Also turn on your TV and make sure that it is set to the correct video

input.

Press  OPEN/CLOSE to open the disc tray.

Load a disc.

Load a disc with the label side facing up, using the disc tray guide

to align the disc (if you’re loading a double-sided DVD-Video disc,

load it with the side you want to play face down).

The player will take a short while to read the disc, after which the

disc type will show up in the front panel display.

Press  to start playback.

• Use the  PAUSE and  buttons to pause or stop playback. You

can resume playback in either case by pressing . See also

Resuming playback on page 23.

• See Playback controls on page 23 for other controls available

during playback.

Getting Started

• Some actions in the Disc Navigator/Home Media Gallery (such

as changing the Browse category) will cause the resume

position to be lost.

Playback controls

Scanning video and audio

CLEAR

ENTER

SUBTITLE ANGLE

OUTPUT

RESOLUTION

You can fast-scan BD/DVD movies, audio CDs, or movie and song

AUDIO

DISPLAY

files forward or backward at various speeds.

During playback, press  or  to start scanning.

There is no sound while scanning video and audio.

Press repeatedly to increase the scanning speed.

The scanning speed is shown on-screen.

To resume normal playback, press .

Depending on the disc, normal playback may automatically resume

when a new chapter is reached on a BD/DVD movie disc.

Selecting titles, chapters and tracks directly

PLAY MODE

PHOTO ZOOM

Resuming playback

CLEAR

ENTER



The resume function offers a convenient way to restart playback

from where you stopped it previously.

You can select titles, chapters and tracks directly with BD, DVD

movies and audio CDs .

•

Use the number buttons to select a title, chapter or track.

• If the disc is stopped, playback starts from the selected title or

track.

Resuming playback of BD/DVD movies and audio CDs

If you stop playback before the end of the disc, the playback stop

position is stored so that you can resume watching the disc from the

same place later.

• If the disc is playing, playback jumps to the start of the selected

chapter or track.

• To resume playback, press . Playback will start from the stored

resume position. For audio CDs, playback resumes from the

beginning of the track.

Skipping content

• Press  again to cancel the resume function.

You can skip over content during playback of BD and DVD movies,

Audio CDs, movie and song files, and photo slideshows.

Note

In the following case, the resume position is cleared:

• Eject the disc.

•

During playback, press  or  to skip content.

• When playing a BD or DVD movie, playback jumps to the start of

the previous/next title, chapter or track. (If the disc is stopped,

playback will start.)

• Use Home Media Gallery/Disc Navigator.

• Switch the player off (DVD resume position remains saved).

• During movie or song file playback, the previous or next file will

start playing.

• Certain BD-ROM discs cannot be restarted from the position in

which they are paused.

• During photo slideshow playback, you can skip to the previous

or next photo.

Resuming playback of movie, music and photo files

Movie and music files are resumed from the start of the title/track

(rather than the stop position within the title/track): photo slideshow

playback is resumed from the photo file within the slideshow.

• If you interrupt playback of a movie or slideshow by pressing

RETURN to display the Disc Navigator or Home Media Gallery

screen, you can still resume playback of the same title/

slideshow photo using the  button, regardless of what is

highlighted on the screen. (Use the ENTER button to start

playback of the currently highlighted item in the Disc Navigator/

Home Media Gallery.)

Note

1 This function may not be supported depending on the content or server software.

2 With some titles on BD-ROM or DVD-Video discs it is not possible to jump to the start of the selected title or chapter.

Getting Started

Play Mode option compatibility

Playing video in slow motion

The available options depend on what kind of disc/file is playing

(=available / =unavailable):

You can play BD and DVD movies and movie files at different

Disc / file type

Play Mode

forward slow motion speeds.

DVD-

PC File

Audio

Option

During playback, press  to start slow motion playback.

BD-ROM

VIDEO (Music) (Movie) (Photo)

• The slow motion speed is shown on-screen.

Time Search

Title Search

Repeat Chapter

Repeat Title

Repeat Track

Repeat All































• There is no sound during slow motion playback.

Press repeatedly to change the slow motion speed.

To resume normal playback, press .

Depending on the disc, normal playback may automatically resume

when a new chapter is reached.

Video step forward and step reverse

Random

Repeat Off



You can use step forward and step reverse when playing a BD or

DVD movie or movie files.

1, 2

Using time search

During playback, press  PAUSE.

Press or to move the video forward or back one step.

To resume normal playback, press .

CLEAR

ENTER

When playing a BD or DVD movie, normal playback may

automatically resume when a new chapter is reached.

You can navigate directly to a certain point in a BD or DVD movie, or

1,3

in a movie file.

Changing the Play Mode

PLAY MODE

During playback, press PLAY MODE and select ‘Time

Search’.

Use the PLAY MODE button on the remote control to select one of

the various playback modes for BD and DVD movie discs, audio CD

discs, movie and music files and photo slideshows.

Use the number buttons to enter a time in hours, minutes

and seconds for playback to resume from.

For a BD or DVD movie, the time you enter should be the time into

the currently playing title. For a movie file it will be the playback time

into the file.

You can’t select a Play Mode while a BD or DVD disc menu is being

displayed, or while playing some BD/DVD movie titles, audio CD, or

movie and music files and photo slideshows.

• For example, press 4, 5, 0, 0 to have playback start from 45

minutes into the title/file. For 1 hour, 20 minutes, press 1, 2, 0,

0, 0.

•

During playback, press PLAY MODE to change the Play

Mode.

• Press CLEAR to clear the input.

See Play Mode option compatibility below for the options available

with the disc/file you’re playing.

Press ENTER to start playback from the time you entered.

•

Time Search (see Using time search below)

Using title search

Title Search (see Using title search below)

•

Repeat Chapter (repeats the current chapter)

•

Repeat Title (repeats the current title)

CLEAR

ENTER

Repeat Track (repeats the current track)

You can directly jump to the start of any title on a BD-ROM or

DVD-Video.

1,3

•

Repeat All (repeats the current browse list)

Random (play tracks from an audio CD, music files, or

During playback, press PLAY MODE and select ‘Title

photo files in a random order)

Search’.

• Repeat Off (cancels the repeat and random modes)

Use the number buttons to select a title.

The current Play Mode is displayed on-screen. Press CLEAR to

resume normal playback.

Press CLEAR to clear the input.

Press ENTER to start playback of the title you selected.

Note

1 This function may not be supported depending on the content or server software.

2 You cannot use step reverse with movie files.

3 With some BD-ROM and DVD-video titles, it is not possible to select any Play Mode options.

Getting Started

• There may be a short delay after pressing the button for the

audio channel to change.

Switching camera angles

ANGLE

Some BD and DVD movies feature scenes shot from two or more

angles — check the disc box for details.

Tip

• Even when multiple audio streams are included in a movie file,

you cannot select from among them while playing back of a

movie file.

•

During playback, press ANGLE to switch the angle.

• There may be a short delay after pressing the button before the

angle changes.

• To set audio language preferences, see Audio Language on

page 42.

• Playback resumes if the angle is changed while paused.

Zooming the screen

PHOTO ZOOM

Displaying disc or file information

DISPLAY

Various track, chapter and title information, as well as the video

transmission rate for DVD and BD movies, can be displayed on-

screen. The information available depends on the type disc or file,

and whether it’s playing or stopped.

During playback of a photo slideshow you can zoom the screen to

2x view or 4x view.

During playback, press PHOTO ZOOM to change the zoom.

Press repeatedly to cycle through: normal  2x zoom  4x zoom.

•

Press DISPLAY to show/switch the information displayed.

Use the cursor keys (///) to move the zoomed area

Press DISPLAY repeatedly to change the displayed information.

of the screen.

The zoom mode is canceled when you stop playback.

Repeat Chapter

Play

DVD-VIDEO

1–2

Chapter

Title Total

0 . 03 . 10

1h 28m 03s

Switching subtitles

SUBTITLE

DVD-Video Play display 1

Repeat Chapter

Play

1–2

0 . 03 . 12

Some BD and DVD movie discs have subtitles in one or more

languages; the disc box will usually tell you which subtitle

languages are available.

DVD-VIDEO

Chapter Time 0 . 02 . 43

Chapter Total 0 . 03 . 16

10 . 08 Mbps

DVD-Video Play display 2

Press SUBTITLE repeatedly to select a subtitle option.

The current subtitle language/option is displayed on-screen and in

the front panel display.

Switching the output video resolution

Subtitle

1/2

English

OUTPUT

RESOLUTION

To switch the subtitle display off, press SUBTITLE then

CLEAR.

You can switch the output video resolution for HDMI and

component output.

There may be a short delay after pressing the button before the

subtitles change.

•

Press OUTPUT RESOLUTION repeatedly to select an output

video resolution.

The current source and output video resolution are shown on-

screen.

Tip

• To set subtitle language preferences, see Subtitle Language on

page 42.

Output Video Resolution: Source Direct

(1080 / 24p)

Source: 1080 / 24p

Switching audio streams/channels

AUDIO

Note

Some BD and DVD movie discs contain multiple audio streams that

you can select on playback. These might be different audio

languages and/or different audio formats (such as a DTS 5.1-

channel sound track and a Dolby Digital 2-channel sound track).

• Depending on your display, some of the settings may result in

the picture disappearing. In this case, press OUTPUT

RESOLUTION repeatedly until the picture re-appears.

• See Changing the output video resolution on page 14 for more

information.

•

Press AUDIO repeatedly to select an audio channel/stream

option.

The current option is shown on-screen.

Audio:

1/2 Dolby Digital 2/0ch

English

Switching audio languages on a BD/DVD movie

Note

1 Some discs only allow you to change the subtitle language from the disc menu. Press POPUP MENU/MENU to access.

2 Some discs only allow you to change the audio language from the disc menu. Press POPUP MENU/MENU to access.

3 There may be instances with some discs where no information can be displayed.

Getting Started

Frequently Asked Questions

• Why won’t the disc I loaded play?

• Why is the mono audio on some discs rather quiet compared to

other discs?

First check that you loaded the disc the right way up (label side

up), and that it’s clean and not damaged. See Taking care of your

player and discs on page 46 for information on cleaning discs.

When mono audio is split into the L and R channels, there may

be a small loss of volume.

If a disc loaded correctly won’t play, it’s probably an

incompatible format or disc type. See Disc/content format

playback compatibility on page 8 for more on disc compatibility.

• There’s no sound when connected using HDMI!

You won’t hear any sound from the HDMI output if your

component is only DVI/HDCP-compatible.

• There’s no picture!

Your TV is probably not compatible with the selected video

output resolution. Check your TV for compatibility with

progressive scan video and higher resolutions. Press the

OUTPUT RESOLUTION button to switch the video output. See

also Changing the output video resolution on page 14.

• I can’t connect to my local area network!

First of all check the settings of the media server you’re using.

Make sure that if you made the network settings automatically

on this player then you also select auto setup on the server.

(Likewise, if you made the settings manually on the server, you

should set up this player manually.)

• I can’t see any picture, or get high definition video output when

playing some BDs!

Check also that you are using the right kind of LAN cable for the

type of connection you made: a standard straight LAN cable if

this player is connected to a hub; a crossed LAN cable for direct

connection to a PC. See also Network connection on page 16.

When playing some discs, there may be no composite video,

S-Video and/or component video output, or high-definition

content may be converted to standard-definition 480i or 480p

component output. This is for content protection. To view the

disc, connect the player to an HDMI-compatible display. See

Connecting for HDMI output on page 13.

• I have a widescreen TV so why are there black bars at the top and

bottom of the screen when I play some discs?

Some movie formats are such that even when played on a

widescreen TV, black bars appear at the top and bottom of the

screen. This is not a malfunction.

• I’ve connected to a HDMI/DVI compatible component but I can’t

get any signal and the front panel HDMI indicator won’t light!

Make sure that you’ve selected this player as the HDMI input in

the settings for the component you’re using. You may need to

refer to the instruction manual of the component to do this.

An HDMI connection can only be made with other HDMI

components, or a High-bandwidth Digital Content Protection

(HDCP)-compatible DVI component. See Connecting for HDMI

output on page 13 for more on HDMI compatibility.

• There’s no picture from the HDMI output!

Make sure the output resolution of this player matches that of

the component you have connected using HDMI. See Changing

the output video resolution on page 14.

• Why is the playback sample rate of the DVD only 48 kHz instead of

96 kHz?

Playback sample rate of the audio is downsampled to 48 kHz.

• My AV receiver is definitely compatible with 96 kHz Linear PCM

audio, but it doesn’t seem to work with this player. What’s wrong?

192 kHz/96 kHz BD and 96 kHz DVD discs only output digital

audio downsampled to 48 kHz through the optical and coaxial

outputs.

96 kHz 7.1ch BD discs only output digital audio downsampled to

48 kHz through HDMI output when video output is 480i or 480p

over HDMI. These are not malfunctions.

Using the Disc Navigator

Chapter 5

Using the Disc Navigator

Use the Disc Navigator to browse through the PC files on a DVD-R/-RW disc to find what you want to play. Additionally, PC files contained

on a BD-ROM can be played back from Disc Navigator. You can use the Disc Navigator when a disc is playing or stopped.

Important

• It’s not possible to use the Disc Navigator with DVD-Video discs, or with Audio CDs.

• You cannot use Disc Navigator with BD-ROM discs that do not contain PC files.

Introduction

Movie Navigator

Most of the features described in this chapter make use of on-

screen displays. Navigate these using the /// and ENTER.

To go back to the previous menu or screen, use the RETURN button.

The button guide at the bottom of every screen shows which buttons

do what.

The movie section of the Disc Navigator allows you to browse and

play all the compatible movie files stored on the loaded BD-ROM or

DVD-R/-RW disc (non-movie files are not displayed).

See also File compatibility on page 9 for more on compatible file

types.

If you haven’t already done so, select ‘Disc Navigator’ from

the Home Menu, then ‘Movies’.

You should see a list of all the movie files found on the disc, together

with their playing times.

POPUP MENU

DISC NAVIGATOR

TOP MENU

20 items

All Movies

ENTER

Scallop-man 3

1:31

1:02

1:31

1:25

1:33

1:26

1:57

1:36

1:18

HOME

Closer

RETURN

Discount store

School of legend

Advance in the future part-2

The EEL

Date: 2006

Genre: Action

Format: WMV

World Baseball

Dream on the way

Finding a southpaw

Dear Customer

Press HOME MENU and select ‘Disc Navigator’ from the on-

• When the movie length cannot be determined, it is displayed as

“-:--”.

screen display.

Alternatively, press DISC NAVIGATOR.

Use the / buttons to change the current selection

(highlighted in yellow).

On the left side of the screen you can see file information, such as

the genre, date and file format, for the current selection.

Home Menu

Disc Navigator

Home Media Gallery

Video/Audio Adjust

Initial Setup

Press ENTER to play the currently highlighted movie.

Press  to start or resume playback from the last title played.

Displaying the Movie Options menu

•

Press  to display the Movie Options menu:

Select ‘Movies’, ‘Photos’ or ‘Music’.

See the sections below for more information on each of these.

20 items

All Movies

Scallop-man 3

Movie Options

Closer

Play from Beginning

Add to Quicklist

Discount store

Disc Navigator

School of legend

Advance in the future part-2

The EEL

Date: 2006

Genre: Action

Format: WMV

World Baseball

Dream on the way

Finding a southpaw

Dear Customer

Movies

Photos

Music

• Play from Beginning: Play the selected movie from the

beginning.

•

Add to Quicklist: Add the selected movie to your Quicklist. The

Quicklist feature is a useful way to organize movie files for handy

selection and playback. The Quicklist can contain up to 25 movies.

Press HOME MENU to exit the Disc Navigator screen.

Note

1 Quicklists are lost when you exit Movie Navigator.

Using the Disc Navigator

Searching movies

Displaying the Browse menu

From the Search sub-menu you can enter a few (up to 20) characters

of a movie title or genre. As each character is entered into the

search field the search results are dynamically updated, narrowing

down the list of movies until you can see the one you’re looking for.

•

Press  to display the Browse menu:

20 items

All Movies

Scallop-man 3

1:31

1:02

1:31

1:25

1:33

1:26

1:57

1:36

1:18

Closer

Loading ...

Discount store

items

Search Results

School of legend

Advance in the future part-2

Scallop-man 3

Say No

1:31

1:02

1:31

1:33

All Movies

The EEL

Browse

Sort

School of legend

Seesaw

World Baseball

Dream on the way

Finding a southpaw

Dear Customer

S _

Depending on the browse menu, certain options may not be

selectable.

Enter

Home Menu

Exit

Select

• All Movies: Display all movie files found on the disc.

• Use the /// and ENTER buttons to select characters

from the keypad.

• Browse: Browse movies by Genre, Quicklist, or Folders. See also

Browsing movies below.

• Select SHFT to toggle between upper and lower case.

• Search: Find a movie by entering a name (or a few letters) to

search for. The search results are narrowed down as you enter

more letters. See also Searching movies below.

• Select SPC to insert a space.

• Select DEL to delete the character at the current cursor position

in the search field.

• Sort: Sort movies by date (oldest first or most recent first) or

alphabetically by title or genre (‘A’ first or ‘Z’ first).

• Select CLR to clear the search field.

• Select DONE to close the keypad and select movies or genres

from the search results; select CANCEL to close the keypad and

clear the search results.

Browsing movies

The Browse sub-menu gives you three ways to browse movies.

20 items

All Movies

Scallop-man 3

1:31

1:02

1:31

1:25

1:33

1:26

1:57

1:36

1:18

Closer

Discount store

School of legend

Advance in the future part-2

The EEL

Go back

Genres

Quicklist

Folders

World Baseball

Dream on the way

Finding a southpaw

Dear Customer

• Go back: Return to the previous menu.

• Genres: Display all movie genres and how many movies are in

each one. Select a genre and press ENTER to see the list of

movies in that genre.

• Quicklist: Display a list of all the movies currently in your

Quicklist. Press  to display the Movie Options menu, where

you can start playback or remove movies from the Quicklist:

20 items

Quicklist

Scallop-man 3

Movie Options

Closer

Play from Begining

Remove

Discount store

School of legend

Advance in the future part-2

The EEL

Date: 2006

Genre: Action

Format: WMV

World Baseball

Dream on the way

Finding a southpaw

Dear Customer

• Folders: Display a list of folders and movie files. Select a folder

and press ENTER to see the list of subfolders/movies files in that

folder. When you play a file in this mode, continuous play of files

in that folder does not occur.

Using the Disc Navigator

• Add to Quicklist: Add the selected photo to your Quicklist. The

Quicklist feature is a useful way to organize photos for handy

selection and slideshow playback. The Quicklist can contain up

Photo Navigator

The photo section of the Disc Navigator allows you to browse and

display all the compatible photo files found on the loaded BD-ROM

or DVD-R/-RW disc (non-photo files are not displayed).

to 25 photos.

See also File compatibility on page 9 for more on compatible file

types.

Displaying the Browse menu

•

Press  to display the browse menu.

• From the left-most column, press to display the browse menu

when displaying photos in thumbnail view:

If you haven’t already done so, select ‘Disc Navigator’ from

the Home Menu, then ‘Photos’.

You should see a list of folders/photo files from the disc.

Use the / buttons to change the current selection

Folder1

30 items

(highlighted in yellow).

Go back

file_001

file_002

file_003

file_004

file_005

file_006

file_007

file_008

file_009

Folders

6 items

All Photos

Browse

Sort

Folder1

Folder2

File1

File2

File3

File4

Depending on the browse menu, certain options may not be

selectable.

• All Photos: Display all photos found on the disc as thumbnail

files.

Select a folder and press ENTER to see the list of photos and

subfolders within the folder.

• Browse: Browse photos by Date, Quicklist or Folders. See also

Browsing photos below.

Folder1

30 items

• Search: Find a photo by entering a name (or a few letters) to

search for. The search results are narrowed down as you enter

more letters. See also Searching photos on page 30.

Go back

file_001

file_002

file_003

file_004

file_005

file_006

file_007

file_008

file_009

• Sort: Sort photos by date (oldest first or most recent first), or

alphabetically by name (‘A’ first or ‘Z’ first).

Browsing photos

The Browse sub-menu gives you several ways to browse photos.

Use the / buttons to change the current selection

(highlighted in yellow).

• Press ENTER to start full-screen slideshow playback from the

currently selected photo.

Folder1

30 items

Go back

file_001

file_002

file_003

file_004

file_005

file_006

file_007

file_008

file_009

• Press  to start or resume slideshow playback from the last

photo displayed.

Go back

Date

Quicklist

Folders

Displaying the Photo Options menu

•

Press  to display the Photo Options menu.

• Press ENTER to display the Photo Options menu when

displaying photos in thumbnail view.

• Go back: Return to the previous menu.

• Date: Browse photos as thumbnails by date (year and month).

Select a year then press ENTER to further browse by month.

Select a month and press ENTER to see the photos taken that

month.

Folder1

30 items

Photo Options

Go back

file_001

file_002

file_003

file_004

file_005

file_006

file_007

file_008

file_009

Slideshow

Add to Quicklist

Date: 1/23/2006

Resolution: 196

Format: JPEG

298

• Slideshow: Start full-screen slideshow playback from the

currently selected photo. During the slideshow, press  to

advance to the next photo; to go back to the previous photo;

 PAUSE to pause the slideshow;  STOP to stop and exit the

slideshow; ZOOM to enlarge the picture on the screen.

Note

1 Quicklists are lost when you exit Photo Navigator.

Using the Disc Navigator

• Quicklist: Display thumbnails of all the photos currently in your

Quicklist. Press ENTER to display the Photo Options menu, from

where you can start slideshow playback or remove photos from

the Quicklist:

Use the / buttons to change the current selection

(highlighted in yellow).

Press ENTER to display the Album list.

Pioneer All Stars

20 items

Quicklist

25 items

Photo Options

Acoustic Guitar

Best of Pioneer All Stars

Cooking Or Eating

Family

20 Songs

13 Songs

10 Songs

12 Songs

18 Songs

11 Songs

18 Songs

10 Songs

13 Songs

21 Songs

Slideshow

Remove

Good!!

File: sample.jpg

Date: 1/23/2006

Resolution: 196

Format: JPEG

Morning Glory

Poker Face

298

Song for You

Tokyo

Two-Tone

Select the Album you want to listen to and press ENTER to

• Folders: Display a list of folders and photo files on the disc.

Select a folder and press ENTER to see the subfolders/photos.

When you play a file in this mode, continuous play of files in that

folder does not occur.

display the Song list.

Acoustic Guitar

20 items

Electrified

9:31

8:00

7:31

3:55

6:33

5:26

4:57

9:36

6:18

End Of The Road

Into The Arena

Keep On Running

Never Let You Go

Open Your Eyes

Pictures Of My Life

Real Sound

Searching photos

From the Search sub-menu you can enter a few (up to 20) characters

of a photo title. As each character is entered into the search field the

search results are dynamically updated, narrowing down the list of

photos until you can see the one you’re looking for.

Artist: Pioneer All Stars

Album: Acoustic Guitar

Genre: Rock

Format: WMA

Rush Street

Take The Time

• When the movie length cannot be determined, it is displayed as

“-:--”.

Search Results

5 items

Use the / buttons to change the current selection

(highlighted in yellow).

R _

On the left side of the screen you can see file information, such as

the artist and album name, genre and file format, for the current

selection.

Enter

Home Menu

Exit

Options

Press ENTER to play the currently highlighted music.

The display shows the Now Playing screen.

See Searching movies on page 28 for how to use the screen keypad.

• Press  to start or resume playback from the last track played

on the Now Playing screen.

Music Navigator

The music section of the Disc Navigator allows you to browse and

play all the compatible music files found on the loaded BD-ROM or

DVD-R/-RW disc (non-music files are not displayed).

Displaying the Song Options menu

•

Press  to display Song Options menu:

See also File compatibility on page 9 for more on compatible file

types.

Acoustic Guitar

20 items

Song Options

If you haven’t already done so, select ‘Disc Navigator’ from

Electrified

End Of The Road

Into The Arena

Keep On Running

Never Let You Go

Open Your Eyes

Pictures Of My Life

Real Sound

Play song

the Home Menu, then ‘Music’.

You should see a list of the artist names on the disc.

Add to Quicklist

Arti

Albumlbu

Gen

FormFo

lternative

ta-0

Artists

20 items

Rush Street

Take The Time

Black Pappers

Album

Albums

Album

Albums

David Jack

Eric Gilberto

King

• Play Song: Play the selected song from the beginning.

Michael Beck

Pioneer All Stars

Rock'n Roll Brothers

The Fishes

• Add to Quicklist: Add the selected song to your Quicklist. The

Quicklist feature is a useful way to organize music files for handy

selection and playback. The Quicklist can contain up to 25

Treetop

William And Marry

songs.

Note

1 Quicklists are lost when you exit Music Navigator.

Using the Disc Navigator

• Folders: Display a list of folders and song files. Select a folder

and press ENTER to see the list of subfolders/songs. When you

play a file in this mode, continuous play of files in that folder

does not occur.

Displaying the Browse menu

•

Press  to display the Browse menu:

Acoustic Guitar

20 items

Searching songs

Electrified

9:31

8:00

7:31

3:55

6:33

5:26

4:57

9:36

6:18

End Of The Road

Into The Arena

Keep On Running

From the Search sub-menu you can enter a few characters (up to 20)

of a song title, genre, artist, or album. As each character is entered

into the search field the search results are dynamically updated,

narrowing down the list until you can see the one you’re looking for.

Never Let You Go

All Songs

Open Your Eyes

Browse

Sort

Now Playing

Pictures Of My Life

Real Sound

Rush Street

Take The Time

Loading ...

items

Search Results

Scallop-man 3

Say No

1:31

1:02

1:31

1:33

Depending on the browse menu, certain options may not be

selectable.

School of legend

Seesaw

• All Songs: Display all songs (files/tracks) found on the disc.

S _

• Browse: Browse songs by Artist, Album, Genre, Quicklist or

Folders. See also Browsing songs below.

• Search: Find a song by entering a name (or a few letters) to

search for. The search results are narrowed down as you enter

more letters. See also Searching songs below.

Enter

Home Menu

Exit

Select

See Searching movies on page 28 for how to use the screen keypad.

• Sort: Sort songs by date (oldest first or most recent first), or

alphabetically by song title, artist, album or genre (‘A’ first or ‘Z’

first).

• Now Playing: Display song information (track name, artist,

album, genre, etc.) and playback information. See also Now

playing song information below.

Now playing song information

The Now Playing screen shows detailed information about the song

playing, including:

• Artist and song title

• Progress bar (elapsed time and song length)

• Album name

Browsing songs

The Browse sub-menu gives you various ways to browse songs.

• Genre

Acoustic Guitar

20 items

Electrified

9:31

8:00

7:31

3:55

6:33

5:26

4:57

9:36

6:18

• File format

End Of The Road

Into The Arena

Keep On Running

Never Let You Go

Open Your Eyes

Pictures Of My Life

Real Sound

• Browse menu

• Play status

Go back

Artists

Albums

Genres

Quicklist

Folders

• Play mode

Rush Street

• Next/Previous song names

Take The Time

• Go back: Return to the previous menu.

Now Playing

• Artists: Display a list of artists, and how many albums are

associated with each. Select an artist and press ENTER to see

the album list by that artist.

Pioneer All Stars

Real Sound

Acoustic Guitar

Genre: Rock

Format: MP3

3:10 / 5:51

All Songs

Browse

Sort

Now Playing

• Albums: Display a list of albums, and how many songs are

associated with each. Select an album and press ENTER to see

the list of songs on that album.

ꢂ

Previous Song

Pictures Of My

Next Song

Rush Street

• Genres: Display all music genres, and how many songs are in

each one. Select a genre and press ENTER to see the list of

artists in that genre.

• Quicklist: Display a list of all the songs currently in your

Quicklist. Press  to display the Song Options menu, where

you can start playback or remove songs from the Quicklist:

Quicklist

20 items

Song Options

Electrified

End Of The Road

Play Song

Remove

Into The Arena

Keep On Running

Never Let You Go

Open Your Eyes

Pictures Of My Life

Real Sound

Artist: Pioneer All Stars

Album: Acoustic Guitar

Genre: Rock

Format: WMA

Rush Street

Take The Time

Using the Home Media Gallery

Chapter 6

Using the Home Media Gallery

DLNA

Introduction

The Home Media Gallery allows you to browse and play movies,

music and photos stored on media servers connected on an

identical Local Area Network (LAN) as the player. This unit allows for

the playing of files stored on the following:

• PCs running Microsoft Windows XP with Windows Media

Connect installed

DLNA CERTIFIED Audio/Video/Image Player

• PCs running Microsoft Windows Vista or XP with Windows

Media Player 11 installed

The Digital Living Network Alliance (DLNA) is a cross-industry

organization of consumer electronics, computing industry and

mobile device companies. Digital Living provides consumers with

easy sharing of digital media through a wired or wireless network in

the home.

• DLNA-compatible digital media servers (on PCs or other

components)

About network playback

The DLNA certification logo makes it easy to find products that

comply with the DLNA Interoperability Guidelines. This unit

complies with DLNA Interoperability Guidelines v1.0.

The network playback function of this unit uses the following

technologies:

When a PC running DLNA server software or other DLNA-

compatible device is connected to this player, some setting changes

of software or other devices may be required. Please refer to the

operating instructions for the software or device for more

information.

Windows Media Connect

See About Windows Media Connect on page 38 for details.

PlaysForSure

DLNA and DLNA CERTIFIED are trademarks and/or service marks of Digital Living

Network Alliance.

Content playable over a network

Even when encoded in a compatible format, some files may not play

correctly. See File compatibility on page 9. Some functions may not

be supported depending on the server type or version used.

PlaysForSure is a marketing certification given by Microsoft. The

PlaysForSure logo makes it easy to find digital media stores and

devices that work together. Digital media purchased from online

stores carrying the PlaysForSure logo is available for use on this

unit.

Supported file formats vary by server. As such, files not supported by

your server are not displayed on this unit.

For more information check with the manufacturer of your server.

This unit complies with PlaysForSure Requirements Specification

for Network Devices Version 2.01.

About playback behavior over a network

• Playback may stall when the PC is switched off or any media

files stored on it are deleted while playing content.

The PlaysForSure logo, Windows Media and the Windows logo are trademarks or

registered trademarks of Microsoft Corporation in the USA and other countries.

• If there are problems within the network environment (heavy

network traffic, etc.) content may not be displayed or played

properly (playback may be interrupted or stalled). For best

performance, a 100BASE-TX connection between player and PC

is recommended.

Windows Media DRM

Microsoft Windows Media Digital Rights Management (WMDRM) is

a platform to protect and securely deliver content for playback on

computers, portable devices and network devices. Home Media

Gallery functions as a WMDRM 10 for networked devices. WMDRM-

protected content can only be played on media servers supporting

WMDRM.

• Playback performance will vary with the power and condition

(seek time of the hard disk, etc.) of the PC being used.

• If several clients are playing simultaneously, as the case may be,

playback is interrupted or stalled.

Content owners use WMDRM technology to protect their intellectual property,

including copyrights. This device uses WMDRM software to access WMDRM-

protected content. If the WMDRM software fails to protect the content, content

owners may ask Microsoft to revoke the software’s ability to use WMDRM to play or

copy protected content. Revocation does not affect unprotected content. When you

download licenses for protected content, you agree that Microsoft may include a

revocation list with the licenses. Content owners may require you to upgrade

WMDRM to access their content. If you decline an upgrade, you will not be able to

access content that requires the upgrade.

• Depending on the security software installed on a connected PC

and the setting of such software, network connection may be

blocked.

• Problems with the PC may cause malfunctions.

Pioneer is not responsible for any malfunction of the player and/or

the Home Media Gallery features due to communication error/

malfunctions associated with your network connection and/or your

PC, or other connected equipment. Please contact your PC

manufacturer or Internet service provider.

This product is protected by certain intellectual property rights of Microsoft. Use or

distribution of such technology outside of this product is prohibited without a license

from Microsoft.

Using the Home Media Gallery

• See the sections below for more information on each part of the

Home Media Gallery.

About the network settings

This unit uses DHCP and Auto IP functionality to make all the

network settings automatically.

Press HOME MENU to exit the Home Media Gallery screen.

If you are using a broadband router or a broadband modem with a

DHCP server function, setup should be completely automatic with

no manual settings required.

Movie Navigator

From the movie section of the Home Media Gallery you can browse

and play all the compatible movie files found on your local area

network (non-movie files are not displayed).

Using the Home Media Gallery

Before using the Home Media Gallery, make sure that you have

connected the player to the network and made the necessary

settings. See Network connection on page 16 and Setting up for

network use on page 21 for more information.

See also File compatibility on page 9 for more on compatible file

types.

If you haven’t already done so, select ‘Home Media Gallery’

from the Home Menu, then ‘Movies’.

HOME MEDIA

GALLERY

You should see a list of all the movie files found on the selected

server, together with their playing times.

1214 items

All Movies

Scallop-man 3

1:31

1:02

1:31

1:25

1:33

1:26

1:57

1:36

1:18

Closer

Discount store

School of legend

Advance in the future part-2

The EEL

Date: 12/01/2006

Genre: Adventure

Format: WMV

World Baseball

Dream on the way

Finding a southpaw

Dear Customer

ENTER

HOME

RETURN

• When the movie length cannot be determined, it is displayed as

“-:--”.

Press HOME MENU and select ‘Home Media Gallery’ from

the on-screen display.

Use the / buttons to change the current selection

(highlighted in yellow).

On the left side of the screen you can see file information, such as

the genre, date and file format, for the current selection.

Home Menu

Press ENTER to play the currently highlighted movie.

Disc Navigator

Home Media Gallery

Video/Audio Adjust

Initial Setup

Press  to start or resume playback from the last title played.

Displaying the Movie Options menu

•

Press  to display the Movie Options menu:

• Alternatively, press HOME MEDIA GALLERY.

1214 items

All Movies

• The Home Media Gallery is only available when the network or

server contains movies, photos or music files.

Scallop-man 3

Movie Options

Closer

Play from Beginning

Add to Quicklist

Discount store

School of legend

Advance in the future part-2

The EEL

Date: 12/01/2006

Genre: Adventure

Format: WMV

Select ‘Movies’, ‘Photos’ or ‘Music’.

World Baseball

Dream on the way

Finding a southpaw

Dear Customer

Home Media Gallery

Movies

Photos

Music

• Play from Beginning: Play the selected movie from the

beginning.

• Add to Quicklist: Add the selected movie to your Quicklist. The

Quicklist feature is a useful way to organize movie files for handy

selection and playback. The Quicklist can contain up to 25

movies.

• On selecting an option, a list of movies, photos or music files

that the player finds on the selected server is displayed. From

here you can browse, play and sort network files.

Note

1 Quicklists are lost in the following instances:

• When you exit Movie Navigator.

• When you change the server to which you are connected.

Using the Home Media Gallery

Searching movies

Displaying the Browse menu

From the Search sub-menu you can enter a few (up to 20) characters

of a movie title or genre. As each character is entered into the

search field the search results are dynamically updated, narrowing

down the list of movies until you can see the one you’re looking for.

•

Press  to display the Browse menu:

1214 items

All Movies

Scallop-man 3

1:31

1:02

1:31

1:25

1:33

1:26

1:57

1:36

1:18

Closer

Discount store

4 items

Search Results

School of legend

Advance in the future part-2

Scallop-man 3

Say No

1:31

1:02

1:31

1:33

All Movies

The EEL

Browse

Sort

Movie Sources

School of legend

Seesaw

World Baseball

Dream on the way

Finding a southpaw

Dear Customer

S _

Depending on the browse menu, certain options may not be

selectable.

Home Menu

Exit

• All Movies: Display all movie files found on the selected server.

• Use the /// and ENTER buttons to select characters

from the keypad.

• Browse: Browse movies by Genre, Quicklist or Folders. See also

Browsing movies below.

• Select SHFT to toggle between upper and lower case.

• Search: Find a movie by entering a name (or a few letters) to

search for. The search results are narrowed down as you enter

more letters. See also Searching movies below.

• Select SPC to insert a space.

• Select DEL to delete the character at the current cursor position

in the search field.

• Sort: Sort movies by date (oldest first or most recent first), or

alphabetically by title or genre (‘A’ first or ‘Z’ first).

• Select CLR to clear the search field.

• Movie Sources: Display servers on the network. See also Movie

sources below.

• Select DONE to close the keypad and select a movie or genre

from the search results; select CANCEL to close the keypad and

clear the search results.

Browsing movies

The Browse sub-menu gives you three ways to browse movies.

Movie sources

From the movie sources window you can see all the servers found

on the network and change the selected server.

1214 items

All Movies

Scallop-man 3

1:31

1:02

1:31

1:25

1:33

1:26

1:57

1:36

1:18

Current server

Closer

Discount store

School of legend

Advance in the future part-2

The EEL

Go back

Genres

Quicklist

Folders

Movie Sources

3 items

World Baseball

Dream on the way

Finding a southpaw

Dear Customer

Family Room Media Center

WMC

DLNA

WMC

Living Room DVD Recorder

Den Computer

Microsoft

Windows Media Connect

2.0

192.168.11.2

Authorized

• Go back: Return to the previous menu.

• Genres: Display all movie genres and how many movies are in

each one. Select a genre and press ENTER to see the list of

movies in that genre.

Pause

SomeSongTil

3:30

Home Menu

Exit

• Quicklist: Display a list of all the movies currently in your

Quicklist. Press  to display the Movie Options menu, where

you can start playback or remove movies from the Quicklist:

• Some servers found on the network may not be available for the

following reasons:

– The player is collecting file information from the server.

– There are no playable movie files on the server.

– This player is not authorized for the PC (Windows Media

Connect only). See also Authorizing this player on page 38.

24 items

Movie Options

Quicklist

Scallop-man 3

Closer

Play from Beginning

Remove

Discount store

• Servers not currently available appear with a lock icon ( ) in the

server list.

School of legend

Advance in the future part-2

The EEL

Date: 12/01/2006

Genre: Adventure

Format: WMV

World Baseball

Dream on the way

Finding a southpaw

Dear Customer

• Folders: Display a list of folders and movie files. Select a folder

and press ENTER to see the list of movies and subfolders within

the folder. (The folder configuration may change depending on

the server type.) When you play a file in this mode, continuous

play of files in that folder does not occur.

Using the Home Media Gallery

Displaying the Browse menu

From the left-most column, press  to display the Browse

Photo Navigator

The photo section of the Home Media Gallery allows you to browse

and display all the compatible photo files found on your local area

network (non-photo files are not displayed).

•

menu:

See also File compatibility on page 9 for more on compatible file

types.

Summer_Vacation

1214 items

If you haven’t already done so, select ‘Home Media Gallery’

from the Home Menu, then ‘Photos’.

You should see a list of albums from the selected server.

All Photos

Browse

Sort

Photo Sources

Albums

6 items

Family

Depending on the browse menu, certain options may not be

selectable.

My_Favorite

School

Sports

Summer_Vacation

Winter_Vacation

• All Photos: Display all photos found on the server.

• Browse: Browse photos by Album, Date, Quicklist or Folders.

See also Browsing photos below.

• Search: Find a photo by entering a name (or a few letters) to

search for. The search results are narrowed down as you enter

more letters. See also Searching photos on page 36.

Use the / buttons to change the current selection

(highlighted in yellow).

• Sort: Sort photos by date (oldest first or most recent first), or

alphabetically by name (‘A’ first or ‘Z’ first).

3 Press ENTER to display the selected photo list.

• Photo Sources: Display servers on the network. See also Photo

sources on page 36.

Summer_Vacation

1214 items

Browsing photos

The Browse sub-menu gives you several ways to browse photos.

File: sample.jpg

Date: 12/06/2006

Resolution: 2196

Format: JPEG

1298

Summer_Vacation

1214 items

Use the /// buttons to change the current

thumbnail selection (highlighted in yellow).

Press  to start or resume slideshow playback from the last photo

displayed.

Go back

Albums

Date

Quicklist

Folders

Displaying the Photo Options menu

• Go back: Return to the previous menu.

•

Press ENTER to display the Photo Options menu:

• Albums: Display a list of server albums.

• Date: Browse photos by date (year and month). Select a year

then press ENTER to further browse by month. Select a month

and press ENTER to see the photos taken that month.

Summer_Vacation

1214 items

Photo Options

Slideshow

• Quicklist: Display thumbnails of all the photos currently in your

Quicklist. Press ENTER to display the Photo Options menu,

where you can start slideshow playback or remove photos from

the Quicklist:

Add to Quicklist

File: sample.jpg

Date: 12/06/2006

Resolution: 2196

Format: JPEG

1298

Quicklist

24 items

Photo Options

• Slideshow: Starts full-screen slideshow playback from the

currently selected photo. During the slideshow, press  to

advance to the next photo; to go back to the previous photo;

 to pause the slideshow;  to stop and exit the slideshow;

ZOOM to enlarge the picture on the screen.

Slideshow

Remove

File: sample.jpg

Date: 12/06/2006

Resolution: 2196

Format: JPEG

1298

• Add to Quicklist: Add the selected photo to your Quicklist. The

Quicklist feature is a useful way to organize photos for handy

selection and slideshow playback. The Quicklist can contain up

to 25 photos.

Note

1 Quicklists are lost in the following instances:

• When you exit Photo Navigator.

• When you change the server to which you are connected.

Using the Home Media Gallery

• Folders: Display a list of folders and photo files. Select a folder

and press ENTER to see a list of photos and subfolders within

the folder. (The folder configuration may change depending on

the server type.) When you play a file in this mode, continuous

play of files in that folder does not occur.

Music Navigator

From the music section of the Home Media Gallery you can browse

and play all the compatible song files found on your local area

network (non-music files are not displayed).

See also File compatibility on page 9 for more on compatible file

types.

Searching photos

From the Search sub-menu you can enter a few (up to 20) characters

of a photo title. As each character is entered into the search field the

search results are dynamically updated, narrowing down the list of

photos until you can see the one you’re looking for.

If you haven’t already done so, select ‘Home Media Gallery’

from the Home Menu, then ‘Music’.

You should see a list of all the artist names found on the selected

server.

5 items

Search Results

Artists

1214 items

Black Pappers

Album

Albums

Album

Albums

David Jack

Eric Gilberto

King

R _

Michael Beck

Pioneer All Stars

Rock'n Roll Brothers

The Fishes

Treetop

William And Marry

Home Menu

Exit

Use the / buttons to change the current selection

See Searching movies on page 34 for how to use the screen keypad.

(highlighted in yellow).

Press ENTER to display the Album list.

Photo sources

From the photo sources window you can see all the servers found on

the network and change the selected server. See Movie sources on

page 34 for more information.

Pioneer All Stars

1214 items

Acoustic Guitar

Best of Pioneer All Stars

Cooking Or Eating

Family

20 Songs

13 Songs

10 Songs

12 Songs

18 Songs

11 Songs

18 Songs

10 Songs

13 Songs

21 Songs

Good!!

Morning Glory

Poker Face

Song for You

Tokyo

Two-Tone

Select the Album you want to listen to and press ENTER to

display the Song list.

Acoustic Guitar

1214 items

Electrified

9:31

8:00

7:31

3:55

6:33

5:26

4:57

9:36

6:18

End Of The Road

Into The Arena

Keep On Running

Never Let You Go

Open Your Eyes

Pictures Of My Life

Real Sound

Artist: Pioneer All Stars

Album: Acoustic Guitar

Genre: Rock

Format: WMA

Rush Street

Take The Time

• When the movie length cannot be determined, it is displayed as

“-:--”.

Use the / buttons to change the current selection

(highlighted in yellow).

On the left side of the screen you can see file information, such as

the artist and album name, genre and file format, for the current

selection.

Press ENTER to play the currently highlighted music.

The display shows the Now Playing screen.

• Press  to start or resume playback from the last track played

on the Now Playing screen.

Using the Home Media Gallery

Browsing songs

Displaying the Song Options menu

The Browse sub-menu gives you various ways to browse songs.

•

Press  to display Song Options menu:

Acoustic Guitar

1214 items

Acoustic Guitar

1214 items

Song Options

Electrified

9:31

8:00

7:31

3:55

6:33

5:26

4:57

9:36

6:18

End Of The Road

Into The Arena

Keep On Running

Never Let You Go

Open Your Eyes

Pictures Of My Life

Real Sound

Electrified

End Of The Road

Into The Arena

Keep On Running

Never Let You Gohe

Open Your Eyes

Pictures Of My Life

Real Sound

Play song

Add to Quicklist

Artist: Pioneer All Stars

Artist:Depeche Mode

Go back

Artists

Album: Acoustic Guitar

Album: Remixes 81-04

Genre: Rock

Genre: Alternative

Format: WMA

Format:WMA

Albums

Genres

Playlists

Quicklist

Folders

Rush Street

Take The Time

Rush Street

Take The Time

• Go back: Return to the previous menu.

• Play Song: Play the selected song from the beginning.

• Artists: Display a list of artists, and how many albums are

associated with each. Select an artist and press ENTER to see

the album list by that artist.

• Add to Quicklist: Add the selected song to your Quicklist. The

Quicklist feature is a useful way to organize music files for handy

selection and playback. The Quicklist can contain up to 25

• Albums: Display a list of albums, and how many songs are

associated with each. Select an album and press ENTER to see

the list of songs on that album.

songs.

Displaying the Browse menu

• Genres: Display all music genres, and how many songs are in

each one. Select a genre and press ENTER to see the list of

artists in that genre.

•

Press  to display the Browse menu:

• Playlists: Display the server Playlists.

Acoustic Guitar

1214 items

• Quicklist: Display a list of all the songs currently in your

Quicklist. Press  to display the Song Options menu, where

you can start playback or remove songs from the Quicklist:

Electrified

9:31

8:00

7:31

3:55

6:33

5:26

4:57

9:36

6:18

End Of The Road

Into The Arena

Keep On Running

Never Let You Go

All Songs

Open Your Eyes

Browse

Sort

Now Playing

Music Sources

Pictures Of My Life

Real Sound

Quicklist

24 items

Song Options

Rush Street

Electrified

Take The Time

End Of The Road

Play song

Remove

Into The Arena

Keep On Running

Never Let You Go

Open Your Eyes

Pictures Of My Life

Real Sound

Artist: Pioneer All Stars

Album: Acoustic Guitar

Genre: Rock

Depending on the browse menu, certain options may not be

selectable.

Format: WMA

• All Songs: Display all songs (files/tracks) found on the server.

Rush Street

Take The Time

• Browse: Browse songs by Artist, Album, Genre, Playlists,

Quicklist or Folders. See also Browsing songs below.

• Folders: Display a list of folders and song files. Select a folder

and press ENTER to see the list of songs and subfolders within

the folder. (The folder configuration may change depending on

the server type.) When you play a file in this mode, continuous

play of files in that folder does not occur.

• Search: Find a song by entering a name (or a few letters) to

search for. The search results are narrowed down as you enter

more letters. See also Searching songs below.

• Sort: Sort songs by date (oldest first or most recent first), or

alphabetically by song title, artist, album or genre (‘A’ first or ‘Z’

first).

Searching songs

From the Search sub-menu you can enter a few characters (up to 20)

of a song title, genre, artist or album. As each character is entered

into the search field the search results are dynamically updated,

narrowing down the list of songs until you can see the one you’re

looking for.

• Now Playing: Display song information (track name, artist,

album, genre, etc.) and playback information. See also Now

playing song information on page 38.

• Music Sources: Display servers on the network. See also Music

sources on page 38.

Loading•••

4 items

Search Results

Reason

1:31

1:02

1:31

1:25

Real Sound

Rolling Dice

Rush Street

R _

Home Menu

Exit

See Searching movies on page 34 for how to use the screen keypad.

Note

1 Quicklists are lost in the following instances:

• When you exit Music Navigator.

• When you change the server to which you are connected.

Using the Home Media Gallery

Now playing song information

The Now Playing screen shows detailed information about the song

playing, including:

About Windows Media Connect

Windows Media Connect is software to deliver music, photos and

movies from a Microsoft Windows XP computer to home stereo

systems and TVs.

• Artist and song title

• Progress bar (elapsed time and song length)

• Album name

With this software, you can play back files stored on the PC through

various devices wherever you like in your home.

• Genre

At this time you cannot download the Windows Media Connect

software from Microsoft’s website. If your server currently does not

have Windows Media Connect installed, install Windows Media

Player 11 (for Windows XP) instead. This software can be

downloaded from Microsoft’s website.

• File format

• Browse menu

• Play status

• Play mode

For more information check the official Microsoft website.

• Next/Previous song names

Authorizing this player

In order to be able to browse and play files from a Windows XP PC

with Windows Media Connect this player must be authorized. This

happens automatically when the player makes a connection over

the network to the PC. If not, please authorize this player manually

on the PC.

Now Playing

Pioneer All Stars

Real Sound

Acoustic Guitar

Genre: Rock

Format: MP3

3:10 / 5:51

All Songs

Browse

ꢂ

Sort

Now Playing

Music Sources

For more information on authorizing this player, refer to the

instruction manual of your server.

Previous Song

Pictures Of My

Next Song

Rush Street

FAQ

Music sources

From the music sources window you can see all the servers found

on the network and change the selected server. See Movie sources

on page 34 for more information.

• Some files don’t show up. Where are they?

– File names that don’t end with one of the permitted extensions

won’t be recognized by this player. See also File compatibility on

page 9.

– Supported file formats vary by server. As such, files not

supported by your server are not displayed on this unit.

For more information check with the manufacturer of your

server.

Video/Audio Adjust menu

Chapter 7

Video/Audio Adjust menu

From the Video/Audio Adjust menu you can make various settings that affect how video is presented on your TV and how the sounds. Items

in the Video/Audio Adjust menu can only be changed during playback.

Creating your own presets

You can create up to three presets of your own.

Video Adjust

• Default setting: Standard

Select one of the Memory presets.

From the Video Adjust screen you can select the Standard or Cinema

video presentation or define presets of your own in Memory 1 to 3.

Press  to select ‘Detailed Settings’ then press ENTER.

Press HOME MENU and select ‘Video/Audio Adjust’ from

the on-screen display.

Memory 1

You can press VIDEO ADJUST on the remote to display the Video

Adjust screen.

Detailed Settings

Adjust the picture quality settings.

• Use the / buttons to select a setting.

Home Menu

• Use the / buttons to adjust the current setting.

Disc Navigator

Home Media Gallery

Video/Audio Adjust

Initial Setup

Memory 1

White Level

Black Level

Hue

Min

Max

Red

Max

Green

Min

Chroma Level

Select ‘Video Adjust’.

Use the / buttons to select a preset.

Select a setting then press ENTER to display just that setting. This

gives you more screen area in which to see the effects of changes

you make.

Standard

Detailed Settings

Memory 1

• Standard – Standard setting

White Level

Min

Max

• Cinema – Optimized for watching movies

• Memory1/Memory2/Memory3 – Use for saving your own

presets (see Creating your own presets below)

• Press ENTER or RETURN to go back to full-screen display.

You can adjust any or all of the following picture quality settings:

Press ENTER or RETURN to make the setting and exit the

• White Level – Adjusts the intensity of white.

Video Adjust screen.

• Black Level – Adjusts the intensity of black.

PureCinema

• Hue – Adjusts the overall color balance between red and green.

There are two types of video signals: Video material, with a frame

rate of 30 frames/second; and film material, that has a frame rate of

24 frames/second.

• Chroma Level – Adjusts how saturated colors appear.

Press RETURN to save the preset and exit the Detailed

Settings screen.

In PureCinema mode film material is converted to 60 frames/second

progressive for an exceptionally clear picture. Video output at 24

frames/second is converted to 60 frames/second.

For film material or sources otherwise recorded with a frame rate of

24 frames/second, video is output in PureCinema mode even if you

have Video Adjust set to Standard, Cinema, or Memory 1, 2 or 3.

Additionally, film materials are output in PureCinema even if you

have the Video Adjust set to Cinema. If you notice problems with the

images projected when set to Cinema (images appear to move, or

zigzag), set the Video Adjust to Standard or Memory 1, 2 or 3.

Note

1 Effective only for video output from HDMI OUT or COMPONENT VIDEO OUT connections (settings do no affect video output from VIDEO OUT or S-VIDEO OUT).

Video/Audio Adjust menu

Audio Adjust

From the Audio Adjust menu you can set the Audio DRC (Dynamic

Range control).

Audio DRC

• Default setting: Off

When watching Dolby Digital BD and DVD discs, as well as PC files

with Dolby Digital audio, at low volume, it’s easy to lose the quieter

sounds completely — including some of the dialog. Switching

Audio DRC to On can help by bringing up the quieter sounds, while

controlling loud peaks.

How much of a difference you hear depends on the material you’re

listening to. If the material doesn’t have wide variations in volume,

you may not notice much change.

Important

• Audio DRC is effective with the following types of audio:

– Analog audio from the AUDIO OUT (2ch) and AUDIO OUT

(5.1ch) jacks.

– PCM audio from the DIGITAL AUDIO OUT and HDMI OUT

jacks (see also About the audio output settings on page 44).

Press HOME MENU and select ‘Video/Audio Adjust’ from

the on-screen display.

Home Menu

Disc Navigator

Home Media Gallery

Video/Audio Adjust

Initial Setup

Select ‘Audio Adjust’.

Video/Audio Adjust

Video Adjust

Audio Adjust

Highlight Audio DRC, then use the / buttons to change

to ‘Off’, ‘Level 1’, ‘Level 2’ or ‘Max’ as required.

Audio Adjust

Audio DRC

Max

Off

Press ENTER or RETURN to make the setting and exit the

Audio Adjust screen.

Initial Setup menu

^CI^hn^api^tt^ei^ra⁸l Setup menu

Using the Initial Setup menu

The Initial Setup menu is where you can set various player options for sound, picture, language and so on. Note that settings can only be

changed when the player is stopped.

If you disconnect the player from the wall outlet before switching the player off, any new settings made during that session will be lost.

•

Press HOME MENU and select ‘Initial Setup’.

In the table below, the default option is marked with a •.

Setting

Options

Explanation

Video Out

4:3 (Standard)

Select if you have a standard 4:3 TV. See Changing the output video resolution on page 14.

When the Output Video Resolution is set to 720p, 1080i or 1080p, video is output in 16:9 widescreen

format even if TV Aspect Ratio is set to 4:3 (Standard). When connected to a 4:3 TV, set the Output

Video Resolution to 480i or 480p. See also Changing the output video resolution on page 14.

TV Aspect Ratio

16:9 (Widescreen) •

Select if you have a widescreen 16:9 TV.

Full

4:3 video material is output without black bars on either side of the picture if the TV Aspect Ratio

4:3 Video Out

setting (above) is set to 16:9 (Widescreen).

Normal •

4:3 video material is output with black bars on either side of the picture if the TV Aspect Ratio setting

(above) is set to 16:9 (Widescreen).

Letter Box •

Pan & Scan

If the TV Aspect Ratio setting (above) is set to 4:3 (Standard), select this if you prefer letterbox

presentation of 16:9 format DVDs.

DVD 16:9 Video Out

If the TV Aspect Ratio setting (above) is set to 4:3 (Standard), select this if you prefer Pan & Scan

presentation of 16:9 format DVDs.

Some discs contain only Letter Box or Pan & Scan presentation so the video output will depend on the disc.

YCbCr •

This is the standard setting for HDMI-compatible devices.

HDMI Color Space

RGB (16–235)

RGB (0–255)

Use this setting if colors appear overly rich and the black too deep on the RGB (0–255) setting.

Use if colors are weak and black appears to ‘float’ on the RGB (16–235) setting.

When using an HDMI monitor that accepts only RGB input, this player outputs RGB video even if this setting is set to YCbCr. If the monitor is DVI-compatible, the player

outputs RGB (0–255) color space. If however the picture looks unnatural, set it to RGB (16–235).

Gives smooth movement in BD/DVD film material video. This setting is only effective when the player

is connected to a 1080/24p-compatible TV using HDMI.

24p Direct Out

Off •

Choose this setting if you notice picture disturbance when the video switches between video and

film material.

When 24p Direct Out is On, you may experience some picture disturbance when the video switches between video and film material. See also Changing the output video

resolution on page 14.

Initial Setup menu

Setting

Options

Explanation

Audio Out

Dolby Digital •

Outputs a Dolby Digital signal when a Dolby Digital source is being played.

Dolby Digital Out

Dolby Digital  PCM

Converts Dolby Digital sources to Linear PCM output. Use if your connected equipment doesn’t

support Dolby Digital audio.

This setting is effective in digital audio outputs.

DTS •

Outputs a DTS signal when a DTS source is being played.

DTS Out

DTS  PCM

Converts sources with DTS audio to Linear PCM output. Use if your connected equipment doesn’t

support DTS audio.

This setting is effective in digital audio outputs.

Stereo •

If you’ve selected DTS  PCM in DTS Out above, you can choose the way the DTS signal is down-

DTS Downmix

mixed PCM audio. Stereo downmixes the signal to 2-channel stereo.

Lt/Rt

Downmixes to a 2-channel signal compatible with Dolby surround matrix decoders. (This allows you

to hear surround sound if your AV receiver or amplifier has Dolby Pro Logic capability.)

Auto •

PCM

Dolby Digital and DTS sources are output as a bitstream signal. However, depending on the HDMI

device connected and the content being played, Linear PCM audio may be output.

HDMI Audio Out

All audio signals are converted to Linear PCM.

Language

English •

Sets the language of the on-screen displays to English.

OSD Language

available languages

English •

Choose from the languages displayed for the on-screen displays.

Sets both the BD-ROM and DVD-Video default audio language to English.

Audio Language

available languages

Choose from the languages displayed to set the default audio language for BD-ROM and DVD-Video

playback.

Other

Continue to the next screen to set the default audio language for BD-ROM and DVD-Video disc

playback. You can select the language name or enter the code number (see on page 49 for the code

list).

Discs do not necessarily have audio in your selected language. Also, some discs override the Audio Language preference.

English •

Sets the default subtitle language for BD-ROM and DVD-Video playback to English.

Subtitle Language

available languages

Choose from the languages displayed to set the default subtitle language for BD-ROM and

DVD-Video playback.

Other

Continue to the next screen to set the default subtitle language for BD-ROM and DVD-Video disc

playback. You can select the language name or enter the code number (see on page 49 for the code

list).

Discs do not necessarily have subtitles in your selected language. Also, some discs override the Subtitle Language preference.

w/Subtitle Language

available languages

Other

•

Sets the language of BD-ROM and DVD-Video menus to the same as that set for the subtitle

language.

BD/DVD Menu

Language

Choose from the displayed languages to set the default language for BD-ROM and DVD-Video

menus.

Continue to the next screen to set the default menu language for BD-ROM and DVD-Video disc

menus. You can select the language name or enter the code number (see on page 49 for the code

list).

Discs do not necessarily have menus in your selected menu language.

On •

Off

Select to have BD-ROM and DVD-Video discs display subtitles.

Select to switch off subtitle display.

Subtitle Display

Some discs may override these settings.

Parental Lock

Next Screen

Set or change the password necessary to play BD or DVD discs that have level/age restrictions. In

order to change the password, you’ll need to first enter your existing one.

Change Password

(Set Password)

Change Level

Enter your password and then set the parental lock level. Discs with a lock level higher than that set

in the player will require the password to play.

DVD Parental Lock

DVD Country Code

Enter your password and then set a country/area code. This ensures that you see the scenes

intended for your country or area. See BD/DVD country/area code list on page 49.

Change Age

Restriction

Enter your password and then set the age restriction.

“255” indicates no parental control.

BD Parental Lock

Only certain discs have parental lock features. Check the disc packaging to see what features the disc has. If you forget your password you can reset it by resetting the player

to its factory settings. See BD/DVD language code list on page 49.

Initial Setup menu

Setting

Options

Explanation

Network

Next Screen

Continue to the next screen to input IP address details. See Setting up for network use on page 21 for

more detailed information.

IP Configuration

Continue to the next screen to set the name of this player as it will appear to other devices on the

network. See Setting up for network use on page 21 for more detailed information.

Device Name

Continue to the next screen to see a summary of your network settings.

Display Network

Config.

Speakers

2 Channel •

5.1 Channel

Next Screen

Set if you connected this player to an amplifier using only the front left/right channels of the AUDIO

OUT (5.1ch) outputs.

Audio Output Mode

Set if you connected this player to an amplifier using all 5.1 channels of the AUDIO OUT (5.1ch) out-

puts. On this setting the audio output from the AUDIO OUT (2ch) jacks will be incorrect.

Continue to the next screen to specify which speakers are connected to your system.

This setting affects how audio is output from the multi-channel analog outputs. See Speaker Setup

on page 45 for more detailed information.

Speaker Setup

Options

On •

The player displays operation displays (Stop, Play, etc.) on-screen.

On Screen Display

Off

Switches off the on-screen operation displays.

Next Screen

Enter your password and then set a country/area code. This ensures that you see the scenes

intended for your country or area. See BD/DVD country/area code list on page 49.

BD Country Code

Auto Power Off

On •

If the player is stopped or paused for more than 30 minutes with no operation by the user, the player

automatically switches itself off.

Off

No automatic power off.

Start

On •

Off

Select to start the Setup Navigator. See also Switching on and setting up on page 20.

Select when using the HDMI Control function. See HDMI Control on page 7.

Select when not using the HDMI Control function. See HDMI Control on page 7.

Playback the BD portion.

Setup Navigator

HDMI Control

BD •

DVD

Set hybrid disc

playback layer

Playback the DVD portion. When no DVD portion is present, the BD portion is played back.

Playback the CD portion. When no CD portion is present, the BD portion is played back.

This setting cannot be changed when a disc is inserted in the disc tray.

Initial Setup menu

About the audio output settings

The table below shows how the audio settings you make in the Initial Setup menu (page 41) affect the output to the analog (2ch/5.1ch), digital

and HDMI outputs with various types of disc/files.

Analog outputs

Digital outputs

HDMI output

Disc audio format

BD-ROM

2ch

5.1ch

PCM convert

Bitstream

PCM

Auto

*11

*8, 11

Dolby Digital

2ch downmix PCM 5.1ch PCM

2ch downmix PCM

Dolby Digital

5.1ch PCM

7.1ch PCM

5.1ch PCM

7.1ch PCM

5.1ch PCM

Dolby Digital

*5, 11

*6, 11

*5, 8, 11

*6, 8, 11

Dolby Digital plus 2ch downmix PCM 5.1ch PCM

*14

2ch downmix PCM 5.1ch PCM

Dolby TrueHD

DTS

*11

*8, 11

DTS

*15

*7, 11

DTS

*7, 8, 11

DTS

DTS-HD

*9, 12,13

*9, 10,12

*9, 12,13

2ch downmix PCM 5.1ch downmix PCM

*10

2ch downmix PCM 2ch downmix PCM

Linear PCM 7.1ch

Linear PCM 5.1ch

7.1ch PCM

5.1ch PCM

*9, 10,12

2ch downmix PCM

2ch PCM

5.1ch PCM

2ch PCM

*12

2ch PCM

Linear PCM 2ch

Dolby Digital

2ch PCM

2ch downmix PCM 5.1ch PCM

2ch downmix PCM Dolby Digital

2ch downmix PCM DTS

DVD-Video

5.1ch PCM

Dolby Digital

DTS

5.1ch PCM

2ch PCM

DTS

MPEG

2ch PCM

Linear PCM

2ch PCM

2 Channel or 5.1 Channel setting (see Audio Output Mode on page 43).

Dolby DigitalPCM or DTSPCM setting (see Dolby Digital Out and DTS Out on page 42).

Dolby Digital or DTS setting (see Dolby Digital Out and DTS Out on page 42).

PCM or Auto setting (see HDMI Audio Out on page 42).

Only the independent substream is output.

Only the Dolby substream is output.

Only the core substream is output.

If the HDMI device you are using is not compatible with these compressed formats, the signal is output as linear PCM.

If the connected HDMI device is compatible with fewer channels of Linear PCM audio than this player, the output will be adjusted to be compatible with the HDMI device.

*10

*11

*12

*13

*14

*15

Outputs 2ch downmix PCM when the sampling rate is 192 kHz.

Even if there is interactive audio, interactive audio is not mixed.

Interactive audio is not mixed when the sampling rate is 192 kHz or 96 kHz.

When the video output of HDMI is 480i or 480p, output sampling rate is automatically downsampled to 48 kHz.

Dolby Digital sound is output.

DTS sound is output.

Note

• Output sampling rate is 48 kHz through the digital audio outputs.

• MPEG audio is always output as linear PCM.

Initial Setup menu

Speaker Setup

You only need to make this setting if you connected this player to your

amplifier using the 5.1 channel analog outputs.

This setting does not affect any digital audio output.

Use the Speaker Setup screen to tell the player what kinds of

speakers you have connected.

Press HOME MENU and select ‘Initial Setup’.

Select ‘Speakers’.

Select ‘Speaker Setup’, then ‘Next Screen’.

Use the / buttons to select a speaker.

Initial Setup

Video Out

Audio Out

Language

Parental Lock

Network

Speaker Setup

Yes

Ls/Rs

Spekaers

Options

L/R

Large

Use the / buttons to change the speaker setup.

Specify which speakers you have in your setup:

• C (Center): Yes or No

• Ls/Rs (Surround): Yes or No

• L/R (Main): Small or Large

(This setting is only applicable if the C and Ls/Rs speakers are

present.)

Press ENTER to save the settings and exit the Speaker Setup

screen.

Additional information

Chapter 9

Additional information

Damaged and odd-shaped discs

Taking care of your player and discs

Discs spin at high speed inside the player. If you can see that a disc

is cracked, chipped, warped, or otherwise damaged, don’t risk using

it in your player — you could end up damaging it.

Handling discs

When holding discs of any type, take care not to leave fingerprints,

dirt or scratches on the disc surface. Hold the disc by its edge or by

the center hole and edge.

Damaged or dirty discs can affect playback performance. Take care

also not to scratch the label side of the disc. Although not as fragile

as the recorded side, scratches can still result in a disc becoming

unusable.

Should a disc become marked with fingerprints, dust, etc., clean

using a soft, dry cloth, wiping the disc lightly from the center to the

outside edge as shown in the diagram below.

This player is designed for use with conventional, fully circular discs

only. Use of shaped discs is not recommended for this product.

Pioneer disclaims all liability arising in connection with the use of

shaped discs.

Do not use any kind of adapter when playing 8 cm DVD discs. This

size disc can be played in this player without an adapter; just use the

smaller disc guide in the disc tray.

Cleaning the pickup lens

Wipe lightly from the center of the disc using straight strokes.

Don’t wipe the disc surface using circular strokes.

The player’s lens should not become dirty in normal use, but if for

some reason it should malfunction due to dust or dirt, consult your

nearest Pioneer-authorized service center. Although lens cleaners

for DVD players are commercially available, we advise against using

them since some may damage the lens.

Problems with condensation

If necessary, use a cloth soaked in alcohol, or a commercially

available DVD/BD cleaning kit to clean a disc more thoroughly.

Never use benzine, thinner or other cleaning agents, including

products designed for cleaning vinyl records.

Condensation may form inside the player if it is brought into a warm

room from outside, or if the temperature of the room rises quickly.

Although the condensation won’t damage the player, it may

temporarily impair its performance. For this reason you should leave

it to adjust to the warmer temperature for about an hour before

switching on and using.

Storing discs

Although BD and DVD discs are more durable than vinyl records,

you should still take care to handle and store discs correctly. When

you’re not using a disc, return it to its case and store upright. Avoid

leaving discs in excessively cold, humid, or hot environments

(including under direct sunlight).

Don’t glue paper or put stickers onto the disc, or use a pencil, ball-

point pen or other sharp-tipped writing instrument. These could all

damage the disc.

For more detailed care information see the instructions that come

with discs.

Do not load more than one disc into the player at a time.

Additional information

Hints on installation

Resetting the player

We want you to enjoy using this product for years to come, so please

bear in mind the following points when choosing a suitable location

for it:

Use this procedure to reset all the player’s settings to the factory

default.

Make sure that the player is off.

Do...

Press  STANDBY/ON and wait until ‘NO DISC,’ ‘BD-ROM,’

• Use in a well-ventilated room.

or ‘DVD’ displays on the front panel.

It can take up to one minute for the system to start once you press

 STANDBY/ON.

• Place on a solid, flat, level surface, such as a table, shelf or

stereo rack.

Press and hold  STOP and press  STANDBY/ON.

• The player turns off with all settings reset.

Don’t...

• Use in a place exposed to high temperatures or humidity,

including near radiators and other heat-generating appliances.

• Place on a window sill or other place where the player will be

exposed to direct sunlight.

• Use in an excessively dusty or damp environment.

• Place directly on top of an amplifier, or other component in your

stereo system that becomes hot in use.

• Place the player on top of or immediately next to the television or

monitor as you may experience interference.

• Use in a kitchen or other room where the player may be exposed

to smoke or steam.

• Use on a thick rug or carpet, or cover with cloth — this may

prevent proper cooling of the unit.

• Place on an unstable surface, or one that is not large enough to

support all four of the unit’s feet.

Moving the player

If you need to move this unit, first remove the disc, if there’s one

loaded, and close the disc tray. Next, press  STANDBY/ON to

switch the power to standby, checking that the power off indication

in the display goes off. Wait at least 10 seconds. Lastly, disconnect

the power cord.

Never lift or move the unit during playback — discs rotate at a high

speed and may be damaged.

Screen sizes and disc formats

BD-ROM and DVD-Video discs come in several different screen

aspect ratios, ranging from TV programs, which are generally 4:3, to

CinemaScope widescreen movies, with an aspect ratio of up to

about 7:3.

Televisions, too, come in different aspect ratios; ‘standard’ 4:3 and

‘widescreen’ 16:9.

Widescreen TV users

If you have a widescreen TV, the TV Aspect Ratio setting (page 41) of

this player should be set to 16:9 (Widescreen).

When you watch discs recorded in 4:3 format, you can use the TV

controls to select how the picture is presented. Your TV may offer

various zoom and stretch options; see the instructions that came

with your TV for details.

Please note that some movie aspect ratios are wider than 16:9, so

even though you have a widescreen TV, these discs will still play in

a ‘letter box’ style with black bars at the top and bottom of the

screen.

Standard TV users

If you have a standard TV, the TV Aspect Ratio setting (page 41) of

this player should be set to 4:3 (Standard).

Additional information

Setting up the remote to control your TV

Input the manufacturer code.

Confirm that the TV is responding to the programmed

While holding down the TV CONTROL  button, input the two digit

code from the table below that corresponds to the make of your TV.

code.

On the remote, press the TV CONTROL  button. If the TV switches

on (or into standby if it was on previously), then you have the correct

code.

For example, if you have a Pioneer TV, press and hold TV CONTROL ,

then press 0, 0 on the remote control.

If nothing happens when you press the TV CONTROL  button,

start again from step 1 using a different code. Some manufacturers

have several codes. Try each one until you find the one that works.

TV Preset code list

Please note that there are cases where only certain functions may be controllable after assigning the proper preset code, or the codes for

the manufacturer in the list will not work for the model that you are using.

Manufacturer Code(s)

ACURA 44

FRONTECH 31, 42, 46

FRONTECH/PROTECH 32

FUJITSU 48

MAGNAVOX 07, 10, 03, 12, 29

MANESTH 39, 46

MARANTZ 07

SALORA 31, 32, 42, 43

SAMBERS 49

ADMIRAL 31

AIWA 60

SAMSUNG 07, 38, 44, 46, 69, 70

SANYO 35, 45, 48, 21, 14, 91

SBR 07, 34

AKAI 32, 35, 42

AKURA 41

FUNAI 40, 46, 58

GBC 32, 42

MARK 07

MATSUI 07, 39, 40, 42, 44, 47, 48

MCMICHAEL 34

MEDIATOR 07

ALBA 07, 39, 41, 44

AMSTRAD 42, 44, 47

ANITECH 44

GE 00, 01, 08, 07, 10, 11, 17, 02, 28, 18

GEC 07, 34, 48

SCHAUB LORENZ 42

SCHNEIDER 07, 41, 47

SEG 42, 46

GELOSO 32, 44

GENERAL 29

MEMOREX 44

METZ 31

ASA 45

ASUKA 41

SEI 32, 40, 49

GENEXXA 31, 41

GOLDSTAR 10, 23, 21, 02, 07, 50

GOODMANS 07, 39, 47, 48, 56

GORENJE 38

MINERVA 31, 53

MITSUBISHI 09, 10, 02, 21, 31

MULTITECH 44, 49

NEC 59

SELECO 31, 42

AUDIOGONIC 07, 36

BASIC LINE 41, 44

BAUR 31, 07, 42

BEKO 38

SHARP 02, 19, 27, 67, 90

SIAREM 32, 49

SIEMENS 31

GPM 41

GRAETZ 31, 42

NECKERMANN 31, 07

NEI 07, 42

NIKKAI 05, 07, 41, 46, 48

NOBLIKO 49

SINUDYNE 32, 39, 40, 49

SKANTIC 43

BEON 07

BLAUPUNKT 31

BLUE SKY 41

BLUE STAR 18

BPL 18

GRANADA 07, 35, 42, 43, 48

GRADIENTE 30, 57

GRANDIN 18

SOLAVOX 31

SONOKO 07, 44

SONOLOR 31, 35

SONTEC 07

NOKIA 32, 42, 52

NORDMENDE 32, 36, 51, 52

OCEANIC 31, 32, 42

ORION 32, 07, 39, 40

OSAKI 41, 46, 48

OSO 41

GRUNDIG 31, 53

HANSEATIC 07, 42

HCM 18, 44

BRANDT 36

BTC 41

SONY 04

SOUNDWAVE 07

STANDARD 41, 44

STERN 31

BUSH 07, 41, 42, 44, 47, 56

CASCADE 44

CATHAY 07

HINARI 07, 41, 44

HISAWA 18

HITACHI 31, 33, 34, 36, 42, 43, 54, 06, 10, 24, OSUME 48

SUSUMU 41

CENTURION 07

CGB 42

25, 18

OTTO VERSAND 31, 32, 07, 42

SYSLINE 07

HUANYU 56

PALLADIUM 38

TANDY 31, 41, 48

TASHIKO 34

CIMLINE 44

HYPSON 07, 18, 46

ICE 46, 47

PANAMA 46

CLARIVOX 07

CLATRONIC 38

CONDOR 38

PANASONIC 31, 07, 08, 42, 22

PATHO CINEMA 42

PAUSA 44

TATUNG 07, 48

IMPERIAL 38, 42

INDIANA 07

TEC 42

TELEAVIA 36

CONTEC 44

INGELEN 31

PHILCO 32, 42

TELEFUNKEN 36, 37, 52

TELETECH 44

CROSLEY 32

CROWN 38, 44

CRYSTAL 42

INTERFUNK 31, 32, 07, 42

INTERVISION 46, 49

ISUKAI 41

PHILIPS 31, 07, 34, 56, 68

PHOENIX 32

TENSAI 40, 41

PHONOLA 07

THOMSON 36, 51, 52, 63

THORN 31, 07, 42, 45, 48

TOMASHI 18

CYBERTRON 41

DAEWOO 07, 44, 56

DAINICHI 41

DANSAI 07

ITC 42

PROFEX 42, 44

ITT 31, 32, 42

PROTECH 07, 42, 44, 46, 49

QUELLE 31, 32, 07, 42, 45, 53

R-LINE 07

JEC 05

TOSHIBA 05, 02, 26, 21, 53

TOWADA 42

JVC 13, 23

DAYTON 44

KAISUI 18, 41, 44

KAPSCH 31

RADIOLA 07

ULTRAVOX 32, 42, 49

UNIDEN 92

DECCA 07, 48

DIXI 07, 44

RADIOSHACK 10, 23, 21, 02

RBM 53

KENDO 42

UNIVERSUM 31, 07, 38, 42, 45, 46, 54

VESTEL 07

DUMONT 53

ELIN 07

KENNEDY 32, 42

KORPEL 07

RCA 01, 10, 15, 16, 17, 18, 61, 62, 09

REDIFFUSION 32, 42

REX 31, 46

VICTOR 13

ELITE 41

KOYODA 44

VOXSON 31

ELTA 44

LEYCO 07, 40, 46, 48

LIESENK&TTER 07

LOEWE 07

ROADSTAR 41, 44, 46

SABA 31, 36, 42, 51

SAISHO 39, 44, 46

WALTHAM 43

EMERSON 42

ERRES 07

WATSON 07

WATT RADIO 32, 42, 49

WHITE WESTINGHOUSE 07

YOKO 07, 42, 46

ZENITH 03, 20

FERGUSON 07, 36, 51

FINLANDIA 35, 43, 54

FINLUX 32, 07, 45, 48, 53, 54

FIRSTLINE 40, 44

FISHER 32, 35, 38, 45

FORMENTI 32, 07, 42

LUXOR 32, 42, 43

M-ELECTRONIC 31, 44, 45, 54, 56, 07, 36, 51

MAGNADYNE 32, 49

MAGNAFON 49

PIONEER 00, 31, 32, 07, 36, 42, 51

Additional information

BD/DVD language code list

Language (Language code letter), Language code

Japanese (ja), 1001

English (en), 0514

French (fr), 0618

German (de), 0405

Italian (it), 0920

Spanish (es), 0519

Dutch (nl), 1412

Russian (ru), 1821

Chinese (zh), 2608

Korean (ko), 1115

Greek (el), 0512

Catalan (ca), 0301

Corsican (co), 0315

Czech (cs), 0319

Welsh (cy), 0325

Danish (da), 0401

Bhutani (dz), 0426

Esperanto (eo), 0515

Estonian (et), 0520

Basque (eu), 0521

Persian (fa), 0601

Finnish (fi), 0609

Fiji (fj), 0610

Faroese (fo), 0615

Frisian (fy), 0625

Irish (ga), 0701

Scots-Gaelic (gd), 0704

Galician (gl), 0712

Guarani (gn), 0714

Gujarati (gu), 0721

Hausa (ha), 0801

Hindi (hi), 0809

Indonesian (in), 0914

Icelandic (is), 0919

Hebrew (iw), 0923

Yiddish (ji), 1009

Javanese (jw), 1023

Georgian (ka), 1101

Kazakh (kk), 1111

Greenlandic (kl), 1112

Cambodian (km), 1113

Kannada (kn), 1114

Kashmiri (ks), 1119

Kurdish (ku), 1121

Kirghiz (ky), 1125

Burmese (my), 1325

Nauru (na), 1401

Nepali (ne), 1405

Norwegian (no), 1415

Occitan (oc), 1503

Oromo (om), 1513

Oriya (or), 1518

SPanjabi (pa), 1601

Polish (pl), 1612

Pashto, Pushto (ps), 1619

Portuguese (pt), 1620

Quechua (qu), 1721

Rhaeto-Romance (rm), 1813

Kirundi (rn), 1814

Romanian (ro), 1815

Kinyarwanda (rw), 1823

Sanskrit (sa), 1901

Sindhi (sd), 1904

Sangho (sg), 1907

Serbo-Croatian (sh), 1908

Sinhalese (si), 1909

lovak (sk), 1911

Slovenian (sl), 1912

Samoan (sm), 1913

Shona (sn), 1914

Serbian (sr), 1918

Siswati (ss), 1919

Sesotho (st), 1920

Sundanese (su), 1921

Swedish (sv), 1922

Swahili (sw), 1923

Tamil (ta), 2001

Telugu (te), 2005

Tajik (tg), 2007

Thai (th), 2008

Tigrinya (ti), 2009

Turkmen (tk), 2011

Tagalog (tl), 2012

Setswana (tn), 2014

Tonga (to), 2015

Turkish (tr), 2018

Tsonga (ts), 2019

Tatar (tt), 2020

Twi (tw), 2023

Ukrainian (uk), 2111

Urdu (ur), 2118

Uzbek (uz), 2126

Vietnamese (vi), 2209

Volapük (vo), 2215

Wolof (wo), 2315

Xhosa (xh), 2408

Yoruba (yo), 2515

Zulu (zu), 2621

Afar (aa), 0101

Abkhazian (ab), 0102

Afrikaans (af), 0106

Amharic (am), 0113

Arabic (ar), 0118

Assamese (as), 0119

Aymara (ay), 0125

Azerbaijani (az), 0126

Bashkir (ba), 0201

Byelorussian (be), 0205

Bulgarian (bg), 0207

Bihari (bh), 0208

Bislama (bi), 0209

Bengali (bn), 0214

Tibetan (bo), 0215

Breton (br), 0218

Latin (la), 1201

Lingala (ln), 1214

Laothian (lo), 1215

Lithuanian (lt), 1220

Latvian (lv), 1222

Malagasy (mg), 1307

Maori (mi), 1309

Macedonian (mk), 1311

Malayalam (ml), 1312

Mongolian (mn), 1314

Moldavian (mo), 1315

Marathi (mr), 1318

Malay (ms), 1319

Croatian (hr), 0818

Hungarian (hu), 0821

Armenian (hy), 0825

Interlingua (ia), 0901

Interlingue (ie), 0905

Inupiak (ik), 0911

Somali (so), 1915

Albanian (sq), 1917

Maltese (mt), 1320

BD/DVD country/area code list

Country/Area, Country/Area code, Country/Area code letter

Argentina, 0118, ar

Australia, 0121, au

Austria, 0120, at

Belgium, 0205, be

Brazil, 0218, br

Finland, 0609, fi

France, 0618, fr

Germany, 0405, de

Hong Kong, 0811, hk

India, 0914, in

Malaysia, 1325, my

Mexico, 1324, mx

Netherlands, 1412, nl

New Zealand, 1426, nz

Norway, 1415, no

Singapore, 1907, sg

Spain, 0519, es

Switzerland, 0308, ch

Sweden, 1905, se

Taiwan, 2023, tw

Canada, 0301, ca

Chile, 0312, cl

China, 0314, cn

Indonesia, 0904, id

Italy, 0920, it

Japan, 1016, jp

Pakistan, 1611, pk

Philippines, 1608, ph

Portugal, 1620, pt

Thailand, 2008, th

United Kingdom, 0702, gb

United States of America, 2119, us

Denmark, 0411, dk

Korea, Republic of, 1118, kr

Russian Federation, 1821, ru

Additional information

Troubleshooting

IIncorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the

points below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If

the trouble cannot be rectified after checking the items below, please contact customer services. In the US, call Toll Free (800) 421-1404.

(Telephone lines are open Monday through Friday 6:00 AM to 4:30 PM (Pacific Time) and Saturday 8:00 AM to 4:30 PM (Pacific Time).) In

Canada, call Local (905) 479-4411, or Long distance +1(877) 283-5901. (Telephone lines are open Monday through Friday 9:00 AM to 5:15 PM

(EST).)

Playback

Problem

Remedy

The disc won’t play or is automatically

ejected after loading.

•Make sure the disc is free from dirt and dust and is not damaged (see Taking care of your player and

discs on page 46).

•Make sure the disc is loaded with the label side face-up and aligned properly in the disc tray guide.

•Incompatible region: If the region on a BD-ROM or DVD-Video disc does not match the region on the

player, the disc cannot be used (see BD-ROM regions and DVD-Video regions on page 10).

•Condensation inside the player: Allow time for condensation to evaporate. Avoid using the player

near an air-conditioning unit.

•Make sure the disc is compatible with this player (see Disc/content format playback compatibility on

page 8).

Picture freezes and the front panel and

remote control buttons stop working.

•Press  (stop), then start playback again ((play)).

•Press the front panel  STANDBY/ON button to switch the power off, then switch back on and

restart playback. If the power fails to switch off, press and hold  STANDBY/ON for 20 seconds until

the power switches off. Then switch on again by pressing  STANDBY/ON.

•Unplug from the wall socket, then plug back in and switch on again by pressing  STANDBY/ON to

switch the player on.

No picture/No color.

•Incorrect video connections: Check that connections are correct and that plugs are inserted fully.

Also check the video cable for damage.

•TV/monitor or AV amplifier settings are incorrect: Check the instruction manual of the connected

equipment.

•Depending on your display, some of the settings may result in the picture disappearing. In this case,

press OUTPUT RESOLUTION repeatedly until the picture re-appears (see Changing the output video

resolution on page 14).

•Some BD-ROM discs output video only over HDMI.

The video output is set to 720p/1080i/

1080p, but the actual output is 480i or

480p.

•For copy-protection purposes, DVD-Video and some BD-ROM discs output 480i or 480p over the

component output.

Screen is stretched or aspect does not

change.

•The TV Aspect Ratio or 4:3 Video Out setting in the Initial Setup menu is incorrect. See TV Aspect Ratio

and 4:3 Video Out on page 41 for how to set these correctly for your TV/monitor.

•When Output Video Resolution is set to 720p, 1080i or 1080p, video is output in 16:9 Widescreen

format even if TV Aspect Ratio is set to 4:3 (Standard).

Picture disturbance during playback or

dark image.

•This player is compatible with Macrovision System copy guard. Some discs include a copy prevention

signal, and when this type of disc is played back, stripes etc., may appear on some sections of the

picture depending on the TV. This is not a malfunction.

•Due to the player’s copy protection circuits, connection of this device through a VCR or an AV

selector may cause picture problems. This is not a malfunction.

No audio, or audio is distorted.

•No audio is output during slow motion playback or when scanning contents.

•Check your amplifier/receiver’s settings (volume, input function, speaker settings, etc.).

•Check that the disc is free from dust and dirt, and that it is not damaged (Taking care of your player

and discs on page 46).

•Check that all interconnects are firmly inserted.

•Check that the plugs and terminals are free of dirt, oxide, etc. and clean if necessary. Also check the

cable for damage.

•Make sure the player’s output is not connected to the amplifier’s phono (turntable) inputs.

•Check the Audio Output Mode on page 43. If this is set to 5.1 Channel, output from the AUDIO OUT

(2ch) jacks will be incorrect.

•Check the Speaker Setup on page 45.

•For copy-protection purposes, some BD-ROM discs only output audio over optical/coaxial and HDMI.

•When Audio CDs containing text files or such data are played back, sound is muted.

The analog audio is OK, but there appears •Check that the Dolby Digital Out and DTS Out settings (see Audio Out on page 42) are suitable for

to be no optical/coaxial digital audio

signal.

your amplifier/receiver — check the instruction manual that came with your amplifier/receiver (also

check that the output settings on your amplifier/receiver are correct).

Additional information

Problem

Remedy

Cannot play multi-channel audio.

•Check the audio options available from the disc menu.

•Multi-channel 192 kHz audio is output in 2 channels.

•Check that the Dolby Digital Out and DTS Out settings (see Audio Out on page 42) are suitable for

your amplifier/receiver — check the instruction manual that came with your amplifier/receiver.

•If you connected this player to your amplifier/receiver using the 5.1 channel analog outputs, make

sure the Audio Output Mode on page 43 and Speaker Setup on page 45 are set correctly.

•If you connected this player to your amplifier/receiver using HDMI, or the optical/coaxial digital

outputs, make sure that the output settings on your amplifier/receiver are correct (refer to the

instruction manual that came with your amplifier/receiver).

•To use the 7.1ch setting for Dolby Digital Out, set Dolby Digital  PCM.

Noise is output when DTS audio is played. •If this unit is connected to a non-DTS compatible amplifier or decoder using a digital audio cable, set

DTS Out to DTSPCM. If you do not do this, noise will be output when you play a DTS disc.

Cannot output 96 kHz or 192 kHz digital

audio from optical/coaxial digital output.

•The player does not output digital audio from the optical/coaxial jacks at this sampling rate. The

digital output is automatically downsampled.

Disc containing PC files won’t play.

•Make sure the disc is compatible with this player (see Disc/content format playback compatibility on

page 8).

•This player is compatible with multi-border discs, but only plays the first border.

•Check that the file complies to one of the supported formats, bit rates or profiles (see File

compatibility on page 9). Also check that the file is not damaged.

•If the message Cannot play this format is displayed when you try to play PC files, check the file

formats.

•This player cannot play DRM-protected content on DVD and DRM-protected titles appear in the Disc

Navigator with a lock icon ( ).

No picture or High Definition video output •For copy-protection purposes, composite, S-video and component video output may not possible. See

when watching a BD. Connecting for HDMI output on page 13 to connect using HDMI.

Image is blurred when you begin playback •Certain televisions cause blur effects when playback of a disc begins. This is not a malfunction.

of a disc.

Tracks/files are repeated during random

play.

•Because tracks/files are selected entirely at random, same tracks/files may be played in quick

succession. For example, ‘Track 1’ may be followed by ‘Track 5,’ only to have ‘Track 1’ play again next.

This is not a malfunction.

SlideShows do not play.

•If you have selected a single file and select Slideshow from the Photo Options menu, then only that

single file is played back. To play a Slideshow you must select All Photos from the Browse menu.

Images no longer displayed when you

change the 24p Direct Out setting to On.

•Depending on your display, some of the settings may result in the picture disappearing. In this case,

press OUTPUT RESOLUTION repeatedly until the picture re-appears (see Changing the output video

resolution on page 14).

HDMI troubleshooting

Problem

Remedy

•This unit has been designed to be compliant with HDMI (High-Definition Multimedia Interface).

Depending on the component you have connected, unreliable signal transfers may result.

•If you connect a DVI device to the HDMI output of this player, ensure that it is compliant with High-

bandwidth Digital Content Protection (HDCP).

No HDMI video output.

(A connected HDMI component doesn’t

work with this player.)

•If the front panel HDMI indicator is unlit then:

– Make sure that you’ve selected this player as the HDMI input in the settings for the component

you’re using. You may need to refer to the instruction manual of the component to do this.

– Check that the HDMI cable is connected properly and that the cable isn’t damaged.

•If the front panel HDMI indicator is lit:

– Depending on your display, some of the settings may result in the picture disappearing. In this case,

press OUTPUT RESOLUTION repeatedly until the picture re-appears (see Changing the output video

resolution on page 14).

•Depending on the HDMI cable being used, 1080p output may not appear correctly.

•Use a different HDMI Color Space setting (see HDMI Color Space on page 41).

Colors are too rich or too weak, or black is

too deep or appears to ‘float’.

•If you have connected to an HDCP-compatible DVI component, there won’t be any audio output from

the HDMI terminal. Connect using the optical/coaxial digital outputs (or the analog outputs).

•This player does not output multi-channel 192 kHz audio. Press AUDIO during playback to switch

between the available audio streams.

No HDMI audio output.

Additional information

Problem

Remedy

HDMI Control does not function.

•Verify that the HDMI cable is firmly connected.

•Make sure that this unit’s HDMI Control is set to On (see HDMI Control on page 43).

•Make sure that the HDMI Control for the connected components is set to On. For more information,

refer to the operating manual for the connected component.

•This function may not work properly if you have multiple components connected to a single plasma

television or AV system (amplifier or AV receiver etc.). For more information refer to the operating

manual of your plasma television or AV system.

•You can enable HDMI Control by turning the HDMI Control setting to On for all components

connected via HDMI cable. Check the video output from this unit once you have completed

making connections and settings for all components. You will need to check the video output

each time you change connected components or remove the HDMI cable.

•Check whether the connected component supports HDMI Control or not. For more information refer

to the operating manual of your plasma television or AV system (amplifier or AV receiver etc.).

•Certain functions are not supported on some plasma televisions.

•This player does not support HDMI Control-compatible components other than those made by

Pioneer.

•This unit will not function properly with components that do not support HDMI Control, or when

connected with components other than those made by Pioneer.

Network troubleshooting

Problem

Remedy

•LAN indicator is unlit:

Home Media Gallery is not available.

– Check the physical connections (hub, 100BASE-TX/10BASE-T or crossed cable and other cable

quality when cabled directly to a PC).

– If the player is connected to a network via a hub, make sure that the Ethernet (CAT-5 LAN) cable

you’re using is a ‘standard’ or ‘straight through’ type.

– If the player is connected directly to a PC, make sure that the Ethernet (CAT-5 LAN) cable you’re

using is a ‘crossed’ or ‘crossover’ type.

•LAN indicator is lit:

– If this player’s IP address is set automatically, make sure that the media server’s address is also set

automatically. If the IP address of the media server has been set manually, set the IP address of the

player manually too (see Network settings page 42).

– Check the logical connections (IP address setup, DHCP, etc.). Confirm that the IP address is correct

if acquired using DHCP or Auto-IP in the Network Config. screen that follows the Initial Setup menu

(see Network settings page 42).

– Confirm that the media server is on and not in standby or sleep mode.

– Check the network and other settings on the media server.

– Check that this player and the media server are on the same Local Area Network (LAN).

– Check if the media server (Windows Media Connect or DLNA-compliant) is running. Restart if

necessary.

– Check if the media server is setup correctly for file sharing, if the target folder has been deleted or if

one or more folders has become corrupted on the server.

– Check if the PC is operating properly. Reboot the PC after confirming its specifications and setup.

•Confirm that the media server is on and not in standby or sleep mode.

•Check the network and other settings on the media server.

•Check that this player and the media server are on the same Local Area Network (LAN).

•Check if the media server (Windows Media Connect or DLNA-compliant) is running. Restart if

necessary.

A connected media server does not show

up in the source list in the Home Media

Gallery.

•Check if the media server is setup correctly for file sharing, if the target folder has been deleted or if

one or more folders has become corrupted on the server.

•Check if the PC is operating properly. Reboot the PC after confirming its specifications and setup.

•Check that there are playable files on the media server.

•After adding a new media server, exit the Home Media Gallery then, after a few moments, re-enter it.

•Check the media server setup. If a client is registered (authorized) manually, the setup procedure

may have to be run again.

•Check that there are playable files on the media server.

A media server shows up in the source list

but is not available (a lock icon (

appears).

)

•After adding a new media server, exit the Home Media Gallery then, after a few moments, re-enter it.

•If the player cannot connect to the same server as last time (because it is switched off, for example),

the player will connect to another server on the network. To see content on a particular server, make

sure it is running and then select it as the source in the Home Media Gallery (see Movie sources on

page 34).

Content different from last time appears

on the network (missing items, etc.).

Additional information

Problem

Remedy

•Check the physical connections (hub, 100BASE-TX/10BASE-T, or crossed cable and other cable

quality when cabled directly to a PC).

Cannot play or display.

•Check if the file complies to the supported format, bit rate or profile (see page 9). Also check if the file

is damaged.

•If the message Cannot play this format is displayed when you try to play PC files, check the file

formats.

•It takes time to capture and display a large-sized image; during this time you may have to wait to

operate the player.

•This player cannot play DRM-protected content stored on a DLNA server (not Windows Media

Connect server).

•Some files that comply with one of the supported formats may not play or be displayed.

•Check if there are too many files on the server.

•Check if the PC is operating properly. Reboot the PC after confirming its specification and setup.

•Check the physical connections (hub, 100BASE-TX/10BASE-T, or crossed cable and other cable

quality when cabled directly to a PC). It is strongly recommended to use 100BASE-TX for playback

quality and display speed.

Image or sound is interrupted or distorted

(block noise appears).

•When connected by a wireless LAN, check if the bit rate is sufficient.

•Check that the file complies with the supported format, bit rate or profile (see File compatibility on

page 9). Also check if the file is damaged.

•Some files that comply with one of the supported formats may not play or be displayed.

•Check if the PC is operating properly. Reboot the PC after confirming its specification and setup.

•The configuration may change depending on server type. This is not a malfunction.

Genre (movie), Playlist (music), Album

(photo) or folder configuration differs from

one server to another.

•Check if the server is correctly set up for file sharing, if the target folder has been deleted, or if one or

more folders have been corrupted on the server.

•Check if there are too many files on the server.

An available server is selected but cannot

be navigated.

Miscellaneous troubleshooting

Problem

Remedy

•It can take up to one minute for the system to start up once you press the  STANDBY/ON button.

This does not mean that the player is experiencing problems.

It is taking a long time for the unit to start

up.

•The Auto Power Off function switches the player into standby if no operation is performed for

30 minutes while the player is stopped or paused. See Auto Power Off on page 43.

The power automatically switches off.

•The CONTROL IN jack on the rear panel is connected: Point the remote control at the connected

component to control this player.

The remote control doesn’t seem to work.

•The remote control is too far from the player, or the angle with the remote sensor is too wide: Use the

remote within its operating range (see Using the remote control on page 8).

•The batteries are exhausted: Put in new ones (see Putting the batteries in the remote control on

page 8).

•If you are using an external IR receiver, you may need to set the IR RECEIVER switch (see Using an

external IR receiver with this player on page 16).

•When the power is cut due to power failure or by unplugging the power cord during operation,

settings will be canceled. See Moving the player on page 47 for proper shutdown instructions.

Settings are canceled.

•When you have inserted a disc containing PC files, the time necessary to load the files contained on

the disc varies by how many files are present. The process can take anywhere from a few minutes to

upwards of ten minutes.

After inserting a disc, a ‘Loading’ message

is displayed but playback does not begin.

•Change the Set hybrid disc playback layer to DVD (see page 43).

On hybrid discs with BD and DVD layers,

the DVD layer cannot be played back.

•Change the Set hybrid disc playback layer to CD (see page 43).

On hybrid discs with BD and CD layers,

the CD layer cannot be played back.

•When the layer set to playback at Set hybrid disc playback layer is not present on an inserted hybrid

disc, the BD layer is played back.

When the Set hybrid disc playback layer is

set to DVD and you insert a hybrid disc

with BD and CD layers, the BD layer is

played back.

•You cannot change the Set hybrid disc playback layer when a disc is inserted. Eject the disc to make

changes.

The Set hybrid disc playback layer setting

cannot be changed (it is grayed out).

Additional information

Problem

Remedy

•A character that cannot be displayed on this unit is included in the file name. Use only alphanumeric

characters if you want file names to be displayed correctly on this player.

A ‘’ appears in the file name.

•This unit’s power may be turned on when you control this unit from a connected plasma television. If

you do not want this unit to be turned on in this way, set this unit’s HDMI Control to Off (see HDMI

Control on page 43).

The power automatically turns on.

Additional information

Interactive audio

Glossary

Interactive audio is Linear PCM (LPCM) audio activated by a BD-

ROM application and mixed with the primary audio. It is typically

used to provide dynamic sounds associated with interactive

applications, such as button sounds.

Analog audio

An electrical signal that directly represents sound. Compare this to

digital audio which can also be an electrical signal, but is an indirect

representation of sound. See also Digital audio.

Interlaced video

A method of displaying a picture in which odd-numbered lines are

updated in one pass, then even-numbered lines updated in the next.

See also Progressive scan video.

Aspect ratio

The width of a TV screen relative to its height. Conventional TVs are

4:3 (in other words, the screen is almost square); widescreen

models are 16:9 (the screen is almost twice as wide as it is high).

IP (Internet Protocol) address

A unique number that devices use in order to identify and

communicate with each other on a network utilizing the Internet

Protocol standard, such as ‘192.168.0.1’. No duplicate numbers are

allowed in the network.

BD-J

BD-J is the Java specification for BD-ROM, allowing content

providers to put interactive material linked to specific titles on the

disc.

LAN cable

Default Gateway

A cable that has an 8-pin modular plug on each end and is different

from a telephone plug which has 4 pins. A straight cable is used

when connecting this player to a home network via a hub. A cross-

over cable is used when connecting directly to a PC.

Default Gateway is a node on a computer network that serves as an

access point to another network. A default gateway (such as a

computer and router) is used to forward all traffic that is not

addressed to a station within the local subnet.

MAC (Media Access Control) address

An address attached to the port of any device. The MAC address

cannot be changed.

DHCP (Dynamic Host Configuration Protocol) Server

A DHCP server is a server that allocates IP addresses to hosts

(network devices). In most cases, a broadband router serves as a

DHCP server in a home network.

PCM (Pulse Code Modulation)

A common system of encoding digital audio. Excellent quality, but

requires a lot of data compared to formats such as Dolby Digital and

MPEG audio. For compatibility with digital audio recorders and AV

amplifiers with digital inputs, this unit can convert Dolby Digital,

DTS and MPEG audio to PCM. See also Digital audio.

Digital audio

An indirect representation of sound by numbers. During recording,

the sound is measured at discrete intervals by an analog-to-digital

converter, generating a stream of numbers. On playback, a digital-

to-analog converter generates an analog signal based on these

numbers. See also Sampling frequency and Analog audio.

Pop-up menu (BD only)

A context-sensitive menu that can be used without interrupting

playback of a BD.

DRM (Digital Rights Management)

DRM is one of several technologies that controls access to and use

of digital data, such as music, movies and other copyrighted

contents.

Progressive scan video

Also called non-interlaced video, this method of displaying a picture

updates all the lines in one pass, resulting in a more stable, flicker-

free image than interlaced video (for a given scanning rate). See also

Interlaced video.

Dynamic range

The difference between the quietest and loudest sounds possible in

an audio signal (without distorting or getting lost in noise). Dolby

Digital and DTS soundtracks are capable of a very wide dynamic

range, delivering dramatic cinema-like effects.

Regions (DVD-Video and BD-ROM)

These associate discs and players with particular areas of the world.

This unit will only play discs that have a compatible region code (i.e.,

the same code as your player). You can find the region code of your

unit by looking on the rear panel. Some discs are compatible with

more than one region (or all regions).

Ethernet

A frame-based computer networking technology for local area

networks (LANs). This player supports 100BASE-TX and 10BASE-T.

Note that the region systems for DVD and BD are not the same.

File extension

A tag added to the end of a filename to indicate the type of file. For

example, “.jpg” indicates an JPEG image file.

Sampling frequency

The rate at which sound is measured to be turned into digital audio

data. The higher the rate, the better the sound quality, but the more

digital information is generated. For example, a sampling frequency

of 44.1 kHz means 44 100 samples (measurements) per second. See

also Digital audio.

HDMI

HDMI (High-Definition Multimedia Interface) is a high-speed digital

interface which has the capability to support standard or high-

definition video plus standard to multi-channel surround-sound

audio on a single digital connection.

Subnet mask

The IP address is divided into the network address part and the host

address part. The subnet mask is expressed as ‘255.255.255.0’. In

most cases, the subnet mask is automatically assigned by the

DHCP server.

Additional information

License

[MPEG4IP]

This software is based in part on Mozilla Public License 1.1 see http://www.mozilla.org/MPL/ for information.

[OpenSSL]

OpenSSL License

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or

other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product includes software developed

by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”.

4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written

permission. For written permission, please contact [email protected].

5. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the

OpenSSL Project.

6. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by the OpenSSL Project for

use in the OpenSSL Toolkit (http://www.openssl.org/)”.

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL

PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE

OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

This product includes cryptographic software written by Eric Young ([email protected]). This product includes software written by Tim Hudson

([email protected]).

Original SSLeay License

This package is an SSL implementation written by Eric Young ([email protected]). The implementation was written so as to conform with Netscapes SSL.

This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found

in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the

same copyright terms except that the holder is Tim Hudson ([email protected]).

Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should

be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online

or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or

other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product includes cryptographic

software written by Eric Young ([email protected])”

The word ‘cryptographic’ can be left out if the routines from the library being used are not cryptographic related:-).

4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: “This

product includes software written by Tim Hudson ([email protected])”

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR

CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING

IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and

put under another distribution licence [including the GNU Public Licence.]

[tiff]

THE SOFTWARE IS PROVIDED “AS-IS” AND WITHOUT WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION,

ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE

FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF

USE, DATA OR PROFITS, WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF LIABILITY, ARISING OUT OF OR IN

CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

Additional information

[Howl]

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,

BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT

SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE

OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

This software is based in part on Apple Public Source License or the recent’s rights thereunder see http://developer.apple.com/ for information.

[UPNPLib/Intel Stack]

This software is based in part on Intel License see http://www.intel.com/ for information.

[JPEG image compression]

If only executable code is distributed, then the accompanying documentation must state that “this software is based in part on the work of the Independent

JPEG Group”.

[libpng]

Randers-Pehrson, and is distributed according to the same disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing

Authors

Cosmin Truta

same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of Contributing Authors

Simon-Pierre Cadieux

Eric S. Raymond

Gilles Vollant

and with the following additions to the disclaimer:

There is no warranty against interference with your enjoyment of the library or against infringement. There is no warranty that our efforts or the library will fulfill

any of your particular purposes or needs. This library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is

with the user.

same disclaimer and license as libpng-0.96, with the following individuals added to the list of Contributing Authors:

Tom Lane

Glenn Randers-Pehrson

Willem van Schaik

as libpng-0.88, with the following individuals added to the list of Contributing Authors:

John Bowler

Kevin Bracey

Sam Bushell

Magnus Holmgren

Greg Roelofs

Tom Tanner

For the purposes of this copyright and license, “Contributing Authors” is defined as the following set of individuals:

Andreas Dilger

Dave Martindale

Guy Eric Schalnat

Paul Schmidt

Tim Wegner

The PNG Reference Library is supplied “AS IS”. The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without

limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc. assume no liability for direct, indirect,

incidental, special, exemplary, or consequential damages, which may result from the use of the PNG Reference Library, even if advised of the possibility of such

damage.

Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the following

restrictions:

1. The origin of this source code must not be misrepresented.

2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source.

3. This Copyright notice may not be removed or altered from any source or altered source distribution.

The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this source code as a component to supporting the PNG

file format in commercial products. If you use this source code in a product, acknowledgment is not required but would be appreciated.

A “png_get_copyright” function is available, for convenient use in “about” boxes and the like: printf(“%s”,png_get_copyright(NULL)); Also, the PNG logo (in PNG

format, of course) is supplied in the files “pngbar.png” and “pngbar.jpg (88x31)” and “pngnow.png” (98x31).

Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open Source Initiative.

Glenn Randers-Pehrson

glennrp at users.sourceforge.net

December 3, 2004

[zlib]

This software is based in part on zlib see http://www.zlib.net for information.

Additional information

[FreeType]

THE FREETYPE PROJECT IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL ANY OF THE AUTHORS OR COPYRIGHT HOLDERS

BE LIABLE FOR ANY DAMAGES CAUSED BY THE USE OR THE INABILITY TO USE, OF THE FREETYPE PROJECT.

[GIFLIB]

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES

OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS

BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR

IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

[libhttp]

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer in this position and unchanged.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or

other materials provided with the distribution.

3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR

ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF

THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The following copyright applies to the base64 code:

Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that both the

above copyright notice and this permission notice appear in all copies, that both the above copyright notice and this permission notice appear in all supporting

documentation, and that the name of M.I.T. not be used in advertising or publicity pertaining to distribution of the software without specific, written prior

permission. M.I.T. makes no representations about the suitability of this software for any purpose. It is provided “as is” without express or implied warranty.

THIS SOFTWARE IS PROVIDED BY M.I.T. “AS IS”. M.I.T. DISCLAIMS ALL EXPRESS OR IMPLIED WARRANTIES WITH REGARD TO THIS SOFTWARE,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL

M.I.T. BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT

OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

[Vera.ttf/VeraMono.ttf]

Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc.

[TinyLogin]

[Shadow Utilities]

Bigelow & Holmes Inc and URW++ GmbH Luxi font license

[Luxi fonts]

trademark of Bigelow & Holmes Inc.

THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR

OTHER RIGHT. IN NO EVENT SHALL BIGELOW & HOLMES INC. OR URW++GMBH. BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,

INCLUDING ANY GEN-ERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR

OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN THE FONT SOFT-WARE.

Additional information

[GNU GENERAL PUBLIC LICENSE]

Version 2, June 1991

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to

guarantee your freedom to share and change free software – to make sure the software is free for all its users. This General Public License applies to most of

the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is

covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to

distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the

software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate

to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make

sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify

the software.

Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software

is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others

will not reflect on the original authors’ reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain

patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not

licensed at all.

The precise terms and conditions for copying, distribution and modification follow.

GNU GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of

this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or

any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or

translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is

not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made

by running the Program). Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and

appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to

the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such

modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed

as a whole at no charge to all third parties under the terms of this License.

c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most

ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that

you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License.

(Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to

print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably

considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as

separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must

be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who

wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to

control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a

storage or distribution medium does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2

above provided that you also do one of the following:

a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above

on a medium customarily used for software interchange; or,

b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source

distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a

medium customarily used for software interchange; or,

Additional information

c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for

noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b

above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means

all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation

of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source

or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component

itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source

code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object

code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify,

sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or

rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program

or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work

based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the

Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy,

distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights

granted herein.

You are not responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed

on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this

License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a

consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all

those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from

distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the

section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section

has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have

made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to

the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder

who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is

permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar

in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”,

you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the

Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10.If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission.

For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our

decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software

generally.

NO WARRANTY

11.BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE

LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT

WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD

THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY

MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS

OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO

OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

Additional information

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which

everyone can redistribute and change under these terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of

warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software

Foundation; either version 2 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or

FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin

Street, Fifth Floor, Boston, MA 02110-1301 USA.

Also add information on how to contact you by electronic and paper mail.

If the program is interactive, make it output a short notice like this when it starts in an interactive mode:

Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ‘show w’. This is free software, and you are welcome to redistribute it under certain

conditions; type ‘show c’ for details.

The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, the commands you use may

be called something other than ‘show w’ and ‘show c’; they could even be mouse-clicks or menu items – whatever suits your program.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the program, if necessary. Here is

a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by James Hacker.

<signature of Ty Coon>, 1 April 1989

Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider

it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of

this License.

[GNU LESSER GENERAL PUBLIC LICENSE]

Version 2.1, February 1999

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to

guarantee your freedom to share and change free software – to make sure the software is free for all its users. This license, the Lesser General Public License,

applies to some specially designated software packages – typically libraries – of the Free Software Foundation and other authors who decide to use it. You can

use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular

case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom

to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the

software and use pieces of it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions

translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure

that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they

can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We

protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute

and/or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed

on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected by problems that might

be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users

of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must

be consistent with the full freedom of use specified in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License,

applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit

linking those libraries into non-free programs.

When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative

of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser

General Public License permits more lax criteria for linking other code with the library.

We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also

provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary

General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard.

To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free

libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.

In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example,

permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU

Linux operating system.

Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library

has the freedom and the wherewithal to run that program using a modified version of the Library.

Additional information

The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based on the library”

and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

GNU LESSER GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party

saying it may be distributed under the terms of this Lesser General Public License (also called “this License”). Each licensee is addressed as “you”.

A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of

those functions and data) to form executables.

The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library” means either

the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications

and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modification”.)

“Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code

for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using

the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use

of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.

1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you conspicuously and

appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to

the absence of any warranty; and distribute a copy of this License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications

or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a) The modified work must itself be a software library.

b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.

c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.

d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an

argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such

function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. (For example, a function in a library to compute

square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied

function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably

considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as

separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must

be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who

wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to

control the distribution of derivative or collective works based on the Library.

In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or

distribution medium does not bring the other work under the scope of this License.

3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter

all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version

than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other

change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and

derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and

2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of

Sections 1 and 2 above on a medium customarily used for software interchange.

If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the

same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object

code.

5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a

“work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.

However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the

Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution of such

executables.

When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the

Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself

a library. The threshold for this to be true is not precisely defined by law.

If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less

in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus

portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing

that work also fall under Section 6, whether or not they are linked directly with the Library itself.

6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce a work containing portions

of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer’s own use and

reverse engineering for debugging such modifications.

You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You

must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among

them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things:

a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work

(which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable

“work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable

containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to

recompile the application to use the modified definitions.)

Additional information

b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already

present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of

the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.

c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge

no more than the cost of performing this distribution.

d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from

the same place.

e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.

For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for reproducing the executable

from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary

form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself

accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating

system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this

License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is

otherwise permitted, and provided that you do these two things:

a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed

under the terms of the Sections above.

b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying

uncombined form of the same work.

8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy,

modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have

received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or

its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work

based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library

or works based on it.

10.Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy,

distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of

the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.

11.If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed

on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this

License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a

consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those

who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution

of the Library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to

apply, and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section

has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have

made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to

the author donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

12.If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who

places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted

only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

13.The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be

similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and “any later version”,

you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the

Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.

14.If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask

for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions

for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and

reuse of software generally.

NO WARRANTY

15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE

LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT

WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE

LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY

MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS

OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE

WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

Additional information

How to Apply These Terms to Your New Libraries

If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute

and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License).

To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion

of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software

Foundation; either version 2.1 of the License, or (at your option) any later version.

This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS

FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.

You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin

Street, Fifth Floor, Boston, MA 02110-1301 USA

Also add information on how to contact you by electronic and paper mail.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a

sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the library ‘Frob’ (a library for tweaking knobs) written by James Random Hacker.

<signature of Ty Coon>, 1 April 1990

Ty Coon, President of Vice

That’s all there is to it!

[Linux Source Notice]

The software programs used on this product include the Linux operating system. The Linux contains software licensed for use based on the terms of a GNU

General Public License. The machine readable copy of the corresponding source code is available for the cost of distribution.

For more information or to obtain a copy, contact your local Pioneer Customer Service center.

Details of the GNU General Public License can be found at the GNU website (http://www.gnu.org).

Additional information

Specifications

General

Audio output (multi-channel/L, R, C, SW, LS, RS)

Output level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . During audio output

200 mVrms (1 kHz, –20 dB)

Number of channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA jack

System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blu-ray Disc PLAYER

(BD-ROM, DVD-Video, DVD-R/-RW, CD, network file playback)

Power requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz

Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 W

Power consumption (standby) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 W

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 kg (14 lb 6 oz)

Dimensions. . . . . . . . . . . . . . . .420 mm (W) x 103 mm (H) x 353 mm (D)

(16 ⁹/16 in. (W) x 4 ¹/16 in. (H) x 13 ¹⁵/16 in. (D))

Operating temperature . . . . . . . . . . +5 °C to +35 °C (+41 °F to +95 °F)

Operating humidity . . . . . . . . . . . . . . . . . 5 % to 85 % (no condensation)

Audio characteristics

Frequency response. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Hz to 22 kHz

S/N ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 dB

Dynamic range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 dB

Total harmonic distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.0015 %

Wow and flutter . . . . . . . . . . . . . . . . . . . . . . . . . . . Limit of measurement

(0.001 % W. PEAK) or lower

HDMI output

HDMI output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 pin

Digital output

Optical digital output . . . . . . . . . . . . . . . . . . . . . . . . . Optical digital jack

Coaxial digital output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA jack

Component Video output (Y, PB, PR

Output level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Y: 1.0 Vp-p (75 Ω)

PB, PR: 0.7 Vp-p (75 Ω)

)

Other terminals

LAN terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethernet jack

10BASE-T/100BASE-TX

Control in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Minijack (3.5 ø)

IR in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Minijack (3.5 ø)

Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA jacks

S-Video output

Y (luminance) - Output level . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω)

C (color) - Output level . . . . . . . . . . . . . . . . . . . . . . . . . . 286 mVp-p (75 Ω)

Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S-Video jack

Accessories

Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

AA/R6P dry cell batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Stereo audio cable (red/white plugs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Video cable (yellow plugs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

LAN cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Warranty card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Operating instructions

Video output

Output level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω)

Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA jack

Audio output (1 stereo pair)

Output level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .During audio output

200 mVrms (1 kHz, –20 dB)

Number of channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA jack

The specifications and design of this product are subject to change without notice.

Additional information

Should this product require service in the U.S.A. and you wish to locate the nearest Pioneer

Authorized Independent Service Company, or if you wish to purchase replacement parts,

operating instructions, service manuals, or accessories, please call the number shown

below.

8 0 0 – 4 2 1 – 1 4 0 4

Please do not ship your product to Pioneer without first calling the Customer Support

Division at the above listed number for assistance.

Pioneer Electronics (USA) Inc.

Customer Support Division

P.O. BOX 1760, Long Beach,

CA 90801-1760, U.S.A.

For warranty information please see the Limited Warranty sheet included with your product.

Should this product require service in Canada, please contact a Pioneer Canadian

Authorized Dealer to locate the nearest Pioneer Authorized Service Company in Canada.

Alternatively, please contact the Customer Satisfaction Department at the following address:

Pioneer Electronics of Canada, Inc.

Customer Satisfaction Department

300 Allstate Parkway, Markham, Ontario L3R 0P2

1-877-283-5901

905-479-4411

For warranty information please see the Limited Warranty sheet included with your product.

Si ce produit doit être réparé au Canada, veuillez vous adresser à un distributeur autorisé

Pioneer du Canada pour obtenir le nom du Centre de Service Autorisé Pioneer le plus près

de chez-vous. Vous pouvez aussi contacter le Service à la clientèle de Pioneer:

Pioneer Électroniques du Canada, Inc.

Service Clientèle

300, Allstate Parkway, Markham, Ontario L3R 0P2

1-877-283-5901

905-479-4411

Pour obtenir des renseignements sur la garantie, veuillez vous reporter au feuillet sur la

garantie restreinte qui accompagne le produit.

S018_B_EF

http://www.pioneerelectronics.com (US)

http://www.pioneerelectronics.ca (Canada)

PIONEER CORPORATION

4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC.

P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404

PIONEER ELECTRONICS OF CANADA, INC.

300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901, 905-479-4411

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300

PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.

Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270

K002_B_En

PIONEER, ELITE, SOUND.VISION.SOUL, and the Pioneer, Elite and

sound.vision.soul logos are trademarks of Pioneer Corporation.

Published by Pioneer Corporation.

<07C000001>

<VRB1466-A>

Printed in Japan

Radio Shack PLCD58MP3 User Manual
PYLE Audio PLVW1342 User Manual
PYLE Audio PLMRKT12 User Manual
Panasonic NV RZ9ENC User Manual
PAC C2R CHYNA User Manual
Metrik Mobile Electronics MIN T66 User Manual
MB QUART FX260 User Manual
Kenwood KRC 208S User Manual
JVC KS U100K User Manual
JVC KD G820 User Manual