Pioneer Car Stereo System DEH 2150UBG User Manual

CD RECEIVER

RADIO CD

CD PLAYER

DEH-2150UBG

DEH-2150UB

Owner’s Manual

Manual de instrucciones

Manual do proprietário

Contents

Handling guideline of discs and player 23

Dual Discs 23

Compressed audio compatibility 24

Handling guideline and supplemental

information 24

– Compressed audio files on the

disc 24

– USB audio player/USB memory 24

Example of a hierarchy 25

– The sequence of audio files on the

disc 25

– The sequence of audio files on USB

memory 25

Specifications 27

Section

Before You Start

About this unit

http://pioneer.jp/group/index-e.html

! We offer the latest information about

Pioneer Corporation on our website.

CAUTION

! Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, damage to this unit, smoke, and over-

heating could result from contact with liquids.

! “CLASS 1 LASER PRODUCT”

Protecting your unit from

theft

The front panel can be detached to deter theft.

This product contains a laser diode of higher

class than 1. To ensure continued safety, do

not remove any covers or attempt to gain ac-

cess to the inside of the product. Refer all ser-

vicing to qualified personnel.

Important

! Handle gently when removing or attaching

the front panel.

! Avoid subjecting the front panel to excessive

shock.

! Keep the front panel out of direct sunlight and

high temperatures.

! Before detaching, be sure to remove the AUX/

USB cable and USB device from the front

panel. Otherwise, this unit, connected device

or vehicle interior may be damaged.

! Keep this manual handy as a reference for op-

erating procedures and precautions.

! Always keep the volume low enough so that

you can hear sounds from outside the vehicle.

! Protect this unit from moisture.

! If the battery is disconnected or discharged,

the preset memory will be erased and must be

reprogrammed.

! Should this unit fail to operate properly, please

contact your dealer or nearest authorized

PIONEER Service Station.

Removing the front panel

Press

(detach) to release the front

panel.

Portable audio player

compatibility

Grab the front panel and remove.

Inquire at the manufacturer about your USB

portable audio player/USB memory.

This unit corresponds to the following.

— USB MSC (Mass Storage Class) compliant

portable audio player and memory

Put the front panel into the provided

— WMA, MP3 and WAV file playback

protective case for safe keeping.

CAUTION

Attaching the front panel

Pioneer accepts no responsibility for data lost on

the USB portable audio player/USB memory even

if that data is lost while using this unit.

Slide the front panel to the left until it

clicks.

Front panel and the head unit are jointed on

the left side. Make sure that the front panel

has been jointed to the head unit.

Visit our website

Visit us at the following site:

Section

Before You Start

! There is a danger of explosion if the battery is

incorrectly replaced. Replace only with the

same or equivalent type.

! Do not handle the battery with metallic tools.

! Do not store the battery with metallic objects.

! If the battery leaks, wipe the remote control

completely clean and install a new battery.

! When disposing of used batteries, comply

with governmental regulations or environmen-

tal public institutions’ rules that apply in your

country/area.

Press the right side of the front panel

until it is firmly seated.

# If you can’t attach the front panel to the head

unit successfully, try again. Front panel may be

damaged if you attach the front panel forcedly.

Using the remote control

Point the remote control in the direction of the

front panel to operate.

! The remote control may not function prop-

erly in direct sunlight.

Important

! Do not store the remote control in high tem-

peratures or direct sunlight.

! Do not let the remote control fall onto the

floor, where it may become jammed under the

brake or accelerator pedal.

Use and care of the remote

control

Installing the battery

Slide the tray on the back of the remote con-

trol out and insert the battery with the plus (+)

and minus (–) poles aligned properly.

WARNING

Keep the battery out of the reach of children.

Should the battery be swallowed, consult a doc-

tor immediately.

CAUTION

! Use one CR2025 (3 V) lithium battery.

! Remove the battery if the remote control is not

used for a month or longer.

Section

Operating this unit

(detach) button

Press to remove the front panel from the

head unit.

What’s what

Head unit

9 AUX input jack (3.5 mm stereo jack)

1 2

4 5

6 7

Use to connect an auxiliary device.

a 1 to 6 buttons

Press for preset tuning. Also used for con-

trolling functions.

! 1/S.Rtrv can be used to control S.RTRV

(sound retriever).

! 2/PAUSE can be used to control PAUSE

(pause).

d c b

! 5/

can be used to control RANDOM

1 SRC/OFF button

(random).

! 6/

peat).

This unit is turned on by selecting a source.

Press to cycle through all the available

sources.

can be used to control REPEAT (re-

b a/b/c/d buttons

/LIST button

Press to perform manual seek tuning, fast

forward, reverse and track search controls.

Also used for controlling functions.

! When operating menus

Press to display the disc title list, track title

list, folder list or file list.

3 MULTI-CONTROL

Turn to increase or decrease the volume.

Also used for controlling functions.

— Pressing a is the same function as

turning MULTI-CONTROL right.

— Pressing b is the same function as

turning MULTI-CONTROL left.

— Pressing c is the same function as

pressing DISP/BACK/SCRL.

— Pressing and holding c is the same

function as pressing and holding

DISP/BACK/SCRL.

4 CLOCK button

Press to change to the clock display.

5 Disc loading slot

Insert a disc to play.

6 h (eject) button

— Pressing d is the same function as

pressing MULTI-CONTROL.

— Pressing and holding d is the same

function as pressing and holding

MULTI-CONTROL.

Press to eject a disc.

7 USB port

Use to connect a USB audio player/USB

memory.

! When connecting, open up the USB con-

nector lid.

! Use a USB cable to connect the USB

audio player/USB memory to the USB

port. Since the USB audio player/USB

memory is projected forward from the

unit, it is dangerous to connect directly.

Pioneer CD-U50E USB cable is also avail-

able. For details, consult your dealer.

! When operating lists

— Pressing a is the same function as

turning MULTI-CONTROL left.

— Pressing b is the same function as

turning MULTI-CONTROL right.

— Pressing c is the same function as

pressing DISP/BACK/SCRL.

Section

Operating this unit

— Pressing and holding c is the same

function as pressing and holding

DISP/BACK/SCRL.

— Pressing d is the same function as

pressing MULTI-CONTROL.

g AUDIO button

Press to select an audio function.

h e button

Press to turn pause on or off.

— Pressing and holding d is the same

function as pressing and holding

MULTI-CONTROL.

i FUNCTION button

Press to select functions.

Press and hold to recall the initial setting

menu when the sources are off.

c DISP/BACK/SCRL button

Press to select different displays.

Press and hold to scroll through the text in-

formation.

j LIST/ENTER button

Press to display the disc title list, track title

list, folder list or file list depending on the

source.

While in the operating menu, press to con-

trol functions.

Press to return to the previous display when

operating the menu.

Press and hold to return to the main menu

when operating the menu.

d BAND/ESC button

Display indication

Press to select among three FM bands and

one AM band.

Press to return to the ordinary display when

operating the menu.

Remote control

Operation is the same as when using the but-

tons on the head unit.

4 6 8

abc

(disc) indicator

Appears when the disc (album) name is dis-

played on the main display section.

(artist) indicator

Appears when the disc (track) artist name is

displayed on the main display section.

3 Main display section

Displays band, frequency, elapsed playback

time and other settings.

! Tuner

Band and frequency are displayed.

! Built-in CD player and USB

Elapsed playback time and literal infor-

mation are displayed.

e VOLUME buttons

Press to increase or decrease the volume.

(song) indicator

Appears when the track (song) name is dis-

played on the main display section.

f MUTE button

Press to turn off the sound. To turn on the

sound, press again.

Section

Operating this unit

Also, appears when a playable audio file is

selected while operating the list.

Selecting a source

You can select a source you want to listen to.

5 c indicator

% Press SRC/OFF repeatedly to switch be-

tween the following sources.

TUNER (tuner)—CD (built-in CD player)—USB

(USB)—AUX (AUX)

Appears when an upper tier of folder or

menu exists.

(folder) indicator

Appears when operating list function.

Notes

7 d indicator

! In the following cases, the sound source will

not change.

Appears when a lower tier of folder or menu

exists.

— When there is no disc in the unit.

— When AUX (auxiliary input) is set to off

(refer to page 16).

8 LOC indicator

Appears when local seek tuning is on.

! When the USB portable audio player/USB

memory is not connected to the USB port of

this unit, NO DEVICE is displayed.

! AUX is set to on by default. Turn off the AUX

when not in use (refer to Switching the auxili-

ary setting on page 16).

! Charging the portable audio player using

car’s DC power source while connecting it to

AUX input may generate noise. In this case,

stop charging.

! When this unit’s blue/white lead is connected

to the vehicle’s auto-antenna relay control

terminal, the vehicle’s antenna extends when

this unit’s source is turned on. To retract the

antenna, turn the source off.

LOUD (loudness) indicator

Appears when loudness is on.

a 5 (stereo) indicator

Appears when the selected frequency is

being broadcast in stereo.

(repeat) indicator

Shows when track repeat is turned on.

Also, shows when folder repeat is on.

(random) indicator

Shows when random play is on.

(Sound Retriever) indicator

Appears when Sound Retriever function is

on.

Adjusting the volume

% Turn MULTI-CONTROL to adjust the

sound level.

Basic Operations

Power ON/OFF

Turning the unit on

Tuner

Basic Operations

% Press SRC/OFF to turn the unit on.

% Select a band

Press BAND/ESC.

Turning the unit off

% Press SRC/OFF and hold until the unit

turns off.

# Press BAND/ESC until the desired band (F1,

F2, F3 for FM or AM) is displayed.

% Manual tuning (step by step)

Press c or d.

Section

Operating this unit

! To return to the ordinary display, press

BAND/ESC.

! If you do not operate functions within about

30 seconds, the display automatically returns

to the ordinary display.

% Seek tuning

Press and hold c or d, and then release.

# You can cancel seek tuning by briefly pressing

c or d.

# While pressing and holding c or d, you can

skip stations. Seek tuning starts as soon as you

release c or d.

Storing the strongest broadcast

frequencies

BSM (best stations memory) automatically

stores the six strongest broadcast frequencies

in the order of their signal strength.

Storing and recalling broadcast

frequencies

You can easily store up to six broadcast fre-

quencies for later recall.

! Six stations for each band can be stored in

memory.

Use MULTI-CONTROL to select BSM in

the function menu.

Press MULTI-CONTROL to turn BSM on.

% When you find a frequency that you

want to store in memory, press one of pre-

set tuning buttons 1 to 6 and hold until the

preset number stops flashing.

Memorized radio station frequency can be re-

called by pressing the preset tuning button.

# You can also recall radio station frequencies

assigned to preset tuning numbers by pressing a

or b during the frequency display.

# To cancel, press MULTI-CONTROL again.

Tuning in strong signals

Local seek tuning lets you tune in only those

radio stations with sufficiently strong signals

for good reception.

Use MULTI-CONTROL to select LOCAL in

the function menu.

Introduction to advanced

operations

Press MULTI-CONTROL to display the

setting mode.

Press MULTI-CONTROL to display the

Turn MULTI-CONTROL to select the de-

main menu.

sired setting.

FM: OFF—LEVEL 1—LEVEL 2—LEVEL 3—

LEVEL 4

AM: OFF—LEVEL 1—LEVEL 2

The LEVEL 4 setting allows reception of only

the strongest stations, while lower settings let

you receive progressively weaker stations.

Use MULTI-CONTROL to select

FUNCTION.

Turn to change the menu option. Press to se-

lect.

Turn MULTI-CONTROL to select the

function.

Press MULTI-CONTROL to determine

BSM (best stations memory)—LOCAL (local

seek tuning)

the selection.

# Even if the menu has been cancelled before

determination, operation is settled.

Notes

! To return to the previous display, press

DISP/BACK/SCRL.

! To return to the main menu, press and hold

DISP/BACK/SCRL.

Section

Operating this unit

! There is sometimes a delay between starting

up disc playback and the sound being issued.

When being read, FRMT READ is displayed.

! If an error message is displayed, refer to Error

messages on page 22.

! Playback is carried out in order of file number.

Folders are skipped if they contain no files. (If

folder 01 (ROOT) contains no files, playback

commences with folder 02.)

Built-in CD Player

Basic Operations

% Insert a CD (CD-ROM) into the disc load-

ing slot.

Playback will automatically start.

# When loading a disc, face the label side of

a disc up.

% Eject a CD (CD-ROM)

Press h (eject).

Displaying text information on

disc

% Select a folder

Press a or b.

% Press DISP/BACK/SCRL to select the de-

sired text information.

For CD TEXT discs

% Select a track

Press c or d.

Play time—DISC TITLE (disc title)—

ARTISTNAME (disc artist name)—

TRACKTITLE (track title)—ARTISTNAME

(track artist name)

% Fast forward or reverse

Press and hold c or d.

# When playing compressed audio, there is no

sound on fast forward or reverse.

For WMA/MP3

Play time—FLD NAME (folder name)—

FILE NAME (file name)—TRACKTITLE (track

title)—ARTISTNAME (artist name)—

ALBUMTITLE (album title)—COMMENT

(comment)—bit rate—folder and track num-

bers

% Return to root folder

Press and hold BAND/ESC.

% Switch between compressed audio and

CD-DA

Press BAND/ESC.

# This operation is available only when playing

CD-EXTRA or MIXED-MODE CDs.

# If you have switched between compressed

audio and CD-DA, playback starts at the first

track on the disc.

For WAV

Play time—FLD NAME (folder name)—

FILE NAME (file name)—sampling frequency

—folder and track numbers

Notes

! You can scroll to the left of the title by pressing

and holding DISP/BACK/SCRL.

! The built-in CD player can play back audio CD

and compressed audio recorded on a CD-

ROM. (Please see the following section for

files that can be played back. Refer to page

24)

! Read the precautions for discs and player on

page 23.

! A disc has already been inserted, press

SRC/OFF to select the built-in CD player.

! Audio CD that contains certain information

such as text and/or number is CD TEXT.

! If the characters recorded on the audio file are

not compatible with this unit, those charac-

ters will not be displayed.

! If specific information is not recorded on a

disc, NO XXXX will be displayed (e.g.,

NO TITLE).

! The text information of some audio files may

not be correctly displayed.

Section

Operating this unit

! Depending on the version of iTunes used to

write MP3 files onto a disc, comment informa-

tion may not be correctly displayed.

! Depending on the version of Windows

Media™ Player used to encode WMA files,

album names and other text information may

not be correctly displayed.

! When playing back VBR (variable bit rate)-re-

corded WMA files, the average bit rate value is

displayed.

! When playing back VBR (variable bit rate)-re-

corded MP3 files, VBR is displayed instead of

bit rate value.

! The sampling frequency shown in the display

may be abbreviated.

Use MULTI-CONTROL to select the de-

sired file name (or folder name).

Turn to change the name of file or folder.

— when a file is selected, press to play.

— when a folder is selected, press to see a list

of files (or folders) in the seleted folder.

— when a folder is selected, press and hold to

play a song in the selected folder.

# To return to the previous list (the folder one

level higher), press DISP/BACK/SCRL.

# To return to the top tier of list, press and hold

DISP/BACK/SCRL.

# To return to the ordinary display, press

BAND/ESC or /LIST.

# If you do not operate the list within about 30

seconds, the display automatically returns to the

ordinary display.

Selecting tracks from the track

title list

Track title list lets you see the list of track titles

on a CD TEXT disc and select one of them to

play back.

Introduction to advanced

operations

Press MULTI-CONTROL to display the

main menu.

Press /LIST to switch to the track title

list mode.

Use MULTI-CONTROL to select

FUNCTION.

Turn to change the menu option. Press to se-

lect.

Use MULTI-CONTROL to select the de-

sired track title.

Turn to change the track title. Press to play.

# To return to the ordinary display, press

BAND/ESC or /LIST.

# If you do not operate the list within about 30

seconds, the display automatically returns to the

ordinary display.

Turn MULTI-CONTROL to select the

function.

REPEAT (repeat play)—RANDOM (random

play)—SCAN (scan play)—PAUSE (pause)—

S.RTRV (sound retriever)

Notes

Selecting files from the file

name list

File name list lets you see the list of file names

(or folder names) and select one of them to

playback.

! To return to the previous display, press

DISP/BACK/SCRL.

! To return to the main menu, press and hold

DISP/BACK/SCRL.

! To return to the ordinary display, press

BAND/ESC.

Press /LIST to switch to the file name

! If you do not operate functions within about

30 seconds, the display automatically returns

to the ordinary display.

list mode.

Names of files and folders appear in the dis-

play.

Section

Operating this unit

Selecting a repeat play range

Pausing playback

% Press 6/

sired setting.

repeatedly to select the de-

% Press 2/PAUSE to turn pause on.

Playback of the current track pauses.

# To turn pause off, press 2/PAUSE again.

# You can also perform this operation in the

menu that appears by using MULTI-CONTROL.

! DISC – Repeat all tracks

! TRACK – Repeat the current track

! FOLDER – Repeat the current folder

# If you select another folder during repeat play,

the repeat play range changes to disc repeat.

# Performing track search or fast forward/re-

verse during TRACK (track repeat) changes the

repeat play range to disc/folder.

# When FOLDER (folder repeat) is selected, it is

not possible to play back a subfolder of that

folder.

Using Sound Retriever

Sound Retriever function automatically en-

hances compressed audio and restores rich

sound.

% Press 1/S.Rtrv repeatedly to select the

desired setting.

OFF (off)—1—2

# 2 is more effective than 1.

# You can also perform this operation in the

menu that appears by using

MULTI-CONTROL.

# You can also perform this operation in the

menu that appears by using MULTI-CONTROL.

Playing tracks in random order

Tracks in a selected repeat range are played in

random order.

% Press 5/

Tracks play in a random order.

# To turn random play off, press 5/

to turn random play on.

Playing songs on USB portable

audio player/USB memory

again.

# You can also perform this operation in the

For details about the supported device, refer to

menu that appears by using MULTI-CONTROL.

Portable audio player compatibility on page 4.

Scanning folders and tracks

Basic Operations

Scan play searches the song within the se-

lected repeat range.

% Select a folder

Press a or b.

Use MULTI-CONTROL to select SCAN in

% Select a track

Press c or d.

the function menu.

on.

Press MULTI-CONTROL to turn scan play

% Fast forward or reverse

Press and hold c or d.

The first 10 seconds of each track is played.

% Return to root folder

Press and hold BAND/ESC.

When you find the desired track press

MULTI-CONTROL to turn scan play off.

# If the display has automatically returned to

the playback display, select SCAN again by using

MULTI-CONTROL.

# After scanning of a disc (folder) is finished,

normal playback of the tracks begins.

Notes

! Optimum performance of this unit may not be

obtained depending on the connected USB

portable audio player/USB memory.

Section

Operating this unit

! If folder 01 (ROOT) contains no files, playback

commences with folder 02.

! When the USB portable audio player having

battery charging function is connected to this

unit and the ignition switch is set to ACC or

ON, the battery is charged.

Function and operation

REPEAT, RANDOM, SCAN, PAUSE and

S.RTRV operations are basically the same as

that of the built-in CD player.

Function name Operation

! You can disconnect the USB portable audio

player/USB memory anytime you want to fin-

ish listening to it.

! If you do not use an USB device, disconnect it

from this unit.

! When the USB portable audio player/USB

memory is disconnected from this unit during

playback, NO DEVICE is displayed.

Refer to Selecting a repeat play

range on the previous page.

However, the repeat play ranges

you can select are different from

that of the built-in CD player. The

repeat play ranges of the USB por-

table audio player/USB memory

are:

REPEAT

TRACK – Repeat just the cur-

rent file

FOLDER – Repeat the current

folder

Displaying text information of

an audio file

The operation is the same as that of the com-

pressed audio on the built-in CD player. (Refer

to Displaying text information on disc on page

10.)

ALL – Repeat all files

Refer to Playing tracks in random

order on the previous page.

RANDOM

SCAN

Refer to Scanning folders and

tracks on the previous page.

Refer to Pausing playback on the

previous page.

PAUSE

Selecting files from the file

name list

Refer to Using Sound Retriever on

the previous page.

S.RTRV

The operation is the same as that of the built-

in CD player. (Refer to Selecting files from the

file name list on page 11.)

Notes

! To return to the previous display, press

DISP/BACK/SCRL.

! To return to the main menu, press and hold

DISP/BACK/SCRL.

! To return to the ordinary display, press

BAND/ESC.

! If you do not operate functions within about

30 seconds, the display automatically returns

to the ordinary display.

! If you select another folder during repeat play,

the repeat play range changes to ALL.

! If you perform track search or fast forward/re-

verse during TRACK, the repeat play range

changes to FOLDER.

Introduction to advanced

operations

Press MULTI-CONTROL to display the

main menu.

Use MULTI-CONTROL to select

FUNCTION.

Turn to change the menu option. Press to se-

lect.

Turn MULTI-CONTROL to select the

function.

! After file or folder scanning is finished, nor-

mal playback of the files begins again.

REPEAT (repeat play)—RANDOM (random

play)—SCAN (scan play)—PAUSE (pause)—

S.RTRV (sound retriever)

Section

Operating this unit

Turn MULTI-CONTROL to adjust speaker

Audio Adjustments

Introduction of audio adjustments

balance.

Front/rear speaker balance can be adjusted

between F15 and R15.

Left/right speaker balance can be adjusted be-

tween L15 and R15.

Press MULTI-CONTROL to display the

main menu.

Use MULTI-CONTROL to select AUDIO.

# FR 0 is the proper setting when only two

speakers are used.

Turn to change the menu option. Press to se-

lect.

Using the equalizer

Turn MULTI-CONTROL to select the

audio function.

There are six stored equalizer settings such as

DYNAMIC, VOCAL, NATURAL, CUSTOM,

FLAT and POWERFUL that can easily be re-

called at any time.

! CUSTOM is an adjusted equalizer curve

that you create.

FAD/BAL (balance adjustment)—EQUALIZER

(equalizer recall)—TONE CTRL (equalizer ad-

justment)—LOUDNESS (loudness)—SLA

(source level adjustment)

Notes

! When FLAT is selected no supplement or

correction is made to the sound.

! To return to the previous display, press

DISP/BACK/SCRL.

! To return to the main menu, press and hold

DISP/BACK/SCRL.

! To return to the ordinary display, press

BAND/ESC.

Recalling equalizer curves

Use MULTI-CONTROL to select

EQUALIZER in the audio function menu.

! When selecting FM as the source, you cannot

switch to SLA.

Press MULTI-CONTROL to display the

setting mode.

! If you do not operate functions within about

30 seconds, the display automatically returns

to the ordinary display.

Turn MULTI-CONTROL to select the

equalizer.

DYNAMIC—VOCAL—NATURAL—CUSTOM

—FLAT—POWERFUL

Using balance adjustment

You can change the fader/balance setting so

that it can provide the ideal listening environ-

ment in all occupied seats.

Press MULTI-CONTROL to determine

the selection.

# Even if the menu has been cancelled before

determination, operation is settled.

Use MULTI-CONTROL to select FAD/BAL

in the audio function menu.

Adjusting equalizer curves

You can adjust the currently selected equalizer

curve setting as desired. Adjusted equalizer

curve settings are memorized in CUSTOM.

Press MULTI-CONTROL to display the

setting mode.

Press MULTI-CONTROL to select the seg-

ment you wish to set.

Press MULTI-CONTROL repeatedly to switch

between fader and balance.

Adjusting bass/mid/treble

You can adjust the bass/mid/treble level.

Section

Operating this unit

Use MULTI-CONTROL to select

Compare the FM volume level with the

TONE CTRL in the audio function menu.

level of the source you wish to adjust.

Press MULTI-CONTROL to display the

Use MULTI-CONTROL to select SLA in

setting mode.

the audio function menu.

Press MULTI-CONTROL to select BASS/

Press MULTI-CONTROL to display the

MID/TREBLE.

setting mode.

Turn MULTI-CONTROL to adjust the

level.

source volume.

+6 to –6 is displayed as the level is increased

or decreased.

+4 to –4 is displayed as the source volume is

increased or decreased.

Press MULTI-CONTROL to determine

the selection.

# Even if the menu has been cancelled before

determination, operation is settled.

# Even if the menu has been cancelled before

determination, operation is settled.

Adjusting loudness

Loudness compensates for deficiencies in the

low- and high-sound ranges at low volume.

Initial Settings

Adjusting initial settings

Press SRC/OFF and hold until the unit

Use MULTI-CONTROL to select

turns off.

LOUDNESS in the audio function menu.

Press MULTI-CONTROL and hold until

Press MULTI-CONTROL to display the

CLOCK SET appears in the display.

setting mode.

Turn MULTI-CONTROL to select one of

Turn MULTI-CONTROL to select the de-

the initial settings.

sired setting.

LOW (low)—HIGH (high)—OFF (off)

CLOCK SET (clock)—FM STEP (FM tuning

step)—AM STEP (AM tuning step)—AUX

(auxiliary input)

Press MULTI-CONTROL to determine

the selection.

# Even if the menu has been cancelled before

determination, operation is settled.

# To return to the previous display, press

DISP/BACK/SCRL.

# To return to the main menu, press and hold

DISP/BACK/SCRL.

# To cancel initial settings, press BAND/ESC.

Adjusting source levels

Source level adjustment (SLA) lets you adjust

the volume level of each source to prevent ra-

dical changes in volume when switching be-

tween sources.

! Settings are based on the FM volume level,

which remains unchanged.

Setting the clock

Use these instructions to set the clock.

Use MULTI-CONTROL to select

CLOCK SET in the initial setting menu.

Refer to Adjusting initial settings on this page.

! The AM volume level can also be adjusted

with source level adjustments.

Section

Operating this unit

Press MULTI-CONTROL to display the

Setting the AM tuning step

setting mode.

# To return to the previous display, press

DISP/BACK/SCRL.

The AM tuning step can be switched between

9 kHz, the preset step, and 10 kHz. When

using the tuner in North, Central or South

America, reset the tuning step from 9 kHz (531

kHz to 1 602 kHz allowable) to 10 kHz (530 kHz

to 1 640 kHz allowable).

Press MULTI-CONTROL to select the seg-

ment of the clock display you wish to set.

Each time you press MULTI-CONTROL, one

segment of the clock display is selected.

Hour—Minute

As you select segments of the clock display,

the selected segment blinks.

Use MULTI-CONTROL to select AM STEP

in the initial setting menu.

Refer to Adjusting initial settings on the pre-

vious page.

Turn MULTI-CONTROL to put a clock

Press MULTI-CONTROL to display the

right.

setting mode.

Turn MULTI-CONTROL to select the AM

Setting the FM tuning step

tuning step.

The FM tuning step employed by seek tuning

can be switched between 100 kHz, the preset

step, and 50 kHz.

! If seek tuning is performed in 50 kHz steps,

stations may be tuned in imprecisely. Tune

in the stations with manual tuning or use

seek tuning again.

10 KHZ (10 kHz)—9 KHZ (9 kHz)

Press MULTI-CONTROL to determine

the selection.

# Even if the menu has been cancelled before

determination, operation is settled.

! The tuning step remains at 50 kHz during

manual tuning.

Switching the auxiliary setting

It is possible to use auxiliary device with this

unit. Activate the auxiliary setting when using

auxiliary device connected to this unit.

Use MULTI-CONTROL to select FM STEP

in the initial setting menu.

Refer to Adjusting initial settings on the pre-

vious page.

Use MULTI-CONTROL to select AUX in

the initial setting menu.

Refer to Adjusting initial settings on the pre-

vious page.

Press MULTI-CONTROL to display the

setting mode.

Turn MULTI-CONTROL to select the FM

Press MULTI-CONTROL to turn AUX on.

tuning step.

50 KHZ (50 kHz)—100 KHZ (100 kHz)

# To turn AUX off, press MULTI-CONTROL

again.

Press MULTI-CONTROL to determine

the selection.

# Even if the menu has been cancelled before

determination, operation is settled.

Other Functions

Using the AUX source

You can connect an auxiliary device to this

unit using a stereo mini plug cable.

Section

Operating this unit

% Insert the stereo mini plug into the

input jack on this unit.

Selecting AUX as the source

% Press SRC/OFF to select AUX as the

source.

# If the auxiliary setting is not turned on, AUX

cannot be selected. For more details, see Switch-

ing the auxiliary setting on the previous page.

Turning the clock display on or off

You can turn the clock display on or off.

! Even when the sources are off, the clock

display appears on the display.

% Press CLOCK to turn the clock display

on or off.

Each press of CLOCK turns the clock display

on or off.

# The clock display disappears temporarily

when you perform other operations, but the clock

display appears again after 25 seconds.

Section

Connections

! Control signal is output through blue/white

cable when this unit is powered on. Connect it

to an external power amp’s system remote

control or the vehicle’s auto-antenna relay

control terminal (max. 300 mA 12 V DC). If the

vehicle is equipped with a glass antenna, con-

nect it to the antenna booster power supply

terminal.

Important

! When this unit is installed in a vehicle without

ACC (accessory) position on the ignition

switch, red cable must be wired to the term-

inal that can detect the operation of the igni-

tion key. Otherwise, battery drain may result.

! Never connect blue/white cable to external

power amp’s power terminal. Also, never con-

nect it to the power terminal of the auto anten-

na. Otherwise, battery drain or malfunction

may result.

! Black cable is ground. This cable and other

product’s ground cable (especially, high-cur-

rent products such as power amp) must be

wired separately. Otherwise, fire or malfunc-

tion may result if they are accidentally de-

tached.

ACC position

No ACC position

! Use of this unit in conditions other than the

following could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4

ohm to 8 ohm (impedance value).

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the

battery before installation.

— Secure the wiring with cable clamps or ad-

hesive tape. To protect the wiring, wrap ad-

hesive tape around them where they lie

against metal parts.

— Place all cables away from moving parts,

such as gear shift and seat rails.

— Place all cables away from hot places,

such as near the heater outlet.

— Do not pass the yellow cable through a

hole into the engine compartment to con-

nect to a battery.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable

of this unit in order to share the power

with other devices. Current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable di-

rectly to ground.

— Never band together multiple speaker’s ne-

gative cables.

Section

Connections

Connection diagram

Power amp

(sold separately)

This product

Rear output

Connect with RCA cables

(sold separately)

Antenna jack

Fuse (10 A)

Wired remote input

Hard-wired remote control adaptor

can be connected (sold separately).

System remote control

Yellow

Blue/white

Connect to the constant 12 V

supply terminal.

Connect to system control terminal of the

power amp or auto-antenna relay control

terminal (max. 300 mA 12 V DC).

Red

Connect to terminal controlled

by ignition switch (12 V DC).

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

Black (chassis ground)

Connect to a clean, paint-free

metal location.

Gray

White

Front speaker

Left

Front speaker

White/black

Green

Gray/black

Right

Violet

Rear speaker

Violet/black

Rear speaker

Green/black

Rear speaker

Perform these connections when using

the optional amplifier.

Section

Installation

space behind the unit, use factory supplied

mounting sleeve.

Important

! Check all connections and systems before

final installation.

Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°)

into place.

! Do not use unauthorized parts. Use of un-

authorized parts may cause malfunctions.

! Consult your dealer if installation requires dril-

ling of holes or other modifications to the vehi-

cle.

Install the unit.

Dashboard

Rubber bush

! Do not install this unit where :

— it may interfere with operation of the vehi-

cle.

— it may cause injury to a passenger as a re-

sult of a sudden stop.

! The semiconductor laser will be damaged if it

overheats. Install this unit away from hot

places such as near the heater outlet.

! Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

Mounting sleeve

Screw

Removing the unit

Extend top and bottom of the trim ring

60°

outwards to remove the trim ring. (When

reattaching the trim ring, point the side

with a groove downwards and attach it.)

! When installing, to ensure proper heat disper-

sal when using this unit, make sure you leave

ample space behind the rear panel and wrap

any loose cables so they are not blocking the

vents.

Trim ring

DIN front/rear mount

! It becomes easy to remove the trim ring if

This unit can be properly installed either from

“Front” (conventional DIN front-mount) or

“Rear” (DIN rear-mount installation, utilizing

threaded screw holes at the sides of unit chas-

sis). For details, refer to the following installa-

tion methods.

the front panel is released.

Insert the supplied extraction keys into

both sides of the unit until they click into

place.

Pull the unit out of the dashboard.

DIN Front-mount

Installation with the rubber bush

Insert the mounting sleeve into the

dashboard.

When installing in a shallow space, use a sup-

plied mounting sleeve. If there is enough

Section

Installation

DIN Rear-mount

Extend top and bottom of the trim ring

outwards to remove the trim ring. (When

reattaching the trim ring, point the side

with a groove downwards and attach it.)

Trim ring

! It becomes easy to remove the trim ring if

the front panel is released.

Determine the appropriate position

where the holes on the bracket and the

side of the unit match.

Tighten two screws on each side.

Screw

Mounting bracket

Dashboard or console

! Use either truss screws (5 mm × 8 mm) or

flush surface screws (5 mm × 9 mm), de-

pending on the shape of screw holes in the

bracket.

Appendix

Additional Information

The connected

USB portable

audio player/

USB memory

contains WMA

files that are pro-

tected by

Play an audio file

not protected by

Windows Media

DRM 9/10.

Error messages

When you contact your dealer or your nearest

Pioneer Service Center, be sure to have the

error message recorded.

SKIPPED

Built-in CD Player

Windows

Media™ DRM 9/

Message

Cause

Action

ERROR-11, 12, Dirty disc

17, 30

Clean disc.

Replace disc.

PROTECT

All the files on

the connected

USB portable

audio player/

USB memory are USB portable

protected by audio player/USB

Windows Media memory and con-

DRM 9/10 nect.

Transfer audio files

not protected by

Windows Media

DRM 9/10 to the

Scratched disc

ERROR-10, 11, Electrical or me- Turn the ignition

12, 15, 17, 30, chanical

switch OFF and

back ON, or switch

to a different

source, then back

to the CD player.

ERROR-15

The inserted disc Replace disc.

does not contain

any data

N/A USB

The USB device Connect a USB

connected to is portable audio

not supported by player or USB

this unit.

memory that is

USB Mass Storage

Class compliant.

ERROR-22, 23 The CD format

cannot be played

back

Replace disc.

CHECK USB

The USB connec- Confirm that the

tor or USB cable USB connector or

is short-circuited. USB cable is not

caught in some-

NO AUDIO

The inserted disc Replace disc.

does not contain

any files that can

be played back

thing or damaged.

SKIPPED

The inserted disc Replace disc.

contains WMA

files that are pro-

The connected

USB portable

audio player/

USB memory

Disconnect the

USB portable

audio player/USB

memory and do

tected by DRM

PROTECT

All the files on

the inserted disc

are secured by

DRM

Replace disc.

consumes more not use it. Turn the

than 500 mA ignition switch to

(maximum allow- OFF, then to ACC

able current).

or ON and then

connect the com-

pliant USB porta-

ble audio player/

USB memory.

USB audio player/USB memory

Message

Cause

Action

NO AUDIO

No songs

Transfer the audio

files to the USB

portable audio

player/USB mem-

ory and connect.

USB memory

Follow the USB

with security en- memory instruc-

abled is con-

nected

tions to disable the

security.

Appendix

Additional Information

! Unfinalized CD-R/CD-RW disc playback is

not possible.

! Do not touch the recorded surface of the

discs.

Communication Perform one of the

failure

following opera-

tions.

ERROR-19

–Turn the ignition

switch OFF and

back ON.

! Store discs in their cases when not in use.

! Avoid leaving discs in excessively hot envir-

onments including under direct sunlight.

! Do not attach labels, write on or apply che-

micals to the surface of the discs.

! To clean a CD, wipe the disc with a soft

cloth outward from the center.

! Condensation may temporarily impair the

player’s performance. Leave it to adjust to

the warmer temperature for about one

hour. Also, wipe any dump discs with a soft

cloth.

–Disconnect the

USB portable

audio player/USB

memory.

–Change to a dif-

ferent source.

Then, return to the

USB portable

audio player/USB

memory.

ERROR-23

USB device is

not formatted

with FAT16 or

FAT32

USB device should

be formatted with

FAT16 or FAT32.

! Playback of discs may not be possible be-

cause of disc characteristics, disc format,

recorded application, playback environ-

ment, storage conditions, and so on.

! Text information may not be correctly dis-

played depending on the recorded environ-

ment.

! Road shocks may interrupt disc playback.

! Read the precautions for discs before

using them.

Handling guideline of discs

and player

! Use only discs featuring either of following

two logos.

Dual Discs

! Dual Discs are two-sided discs that have a

recordable CD for audio on one side and a

recordable DVD for video on the other.

! Since the CD side of Dual Discs is not phy-

sically compatible with the general CD

standard, it may not be possible to play the

CD side with this unit.

! Use only conventional, fully circular discs.

Do not use shaped discs.

! Frequent loading and ejecting of a Dual

Disc may result in scratches on the disc.

Serious scratches can lead to playback pro-

blems on this unit. In some cases, a Dual

Disc may become stuck in the disc loading

slot and will not eject. To prevent this, we

recommend you refrain from using Dual

Disc with this unit.

! Use 12-cm or 8-cm CD. Do not use an

adapter when playing 8-cm CDs.

! Do not insert anything other than a CD into

the CD loading slot.

! Do not use cracked, chipped, warped, or

otherwise damaged discs as they may da-

mage the player.

Appendix

Additional Information

! Please refer to the information from the

disc manufacturer for more detailed infor-

mation about Dual Discs.

! Only 32 characters from beginning can be

displayed as a file name (including the file

extension) or a folder name.

! The text information of some audio files

may not be correctly displayed.

! This unit may not operate correctly depend-

ing on the application used to encode

WMA files.

Compressed audio

compatibility

WMA

! Compatible format: WMA encoded by

Windows Media Player

! File extension: .wma

! Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps

to 384 kbps (VBR)

! Sampling frequency: 32 kHz, 44.1 kHz, 48

kHz

Compressed audio files on the disc

! ISO 9660 Level 1 and 2 compliant. Romeo

and Joliet file systems are both compatible

with this player.

! Multi-session playback is possible.

! Compressed audio files are not compatible

with packet write data transfer.

! Regardless of the length of blank section

between the songs of original recording,

compressed audio discs play with a short

pause between songs.

! Windows Media Audio 9 Professional, Loss-

less, Voice: No

MP3

! File extension: .mp3

! Bit rate: 8 kbps to 320 kbps (CBR), VBR

! Sampling frequency: 16 kHz to 48 kHz (32,

44.1, 48 kHz for emphasis)

USB audio player/USB memory

! Compatible ID3 tag version: 1.0, 1.1, 2.2,

2.3, 2.4 (ID3 tag Version 2.x is given priority

than Version 1.x.)

! M3u playlist: No

! MP3i (MP3 interactive), mp3 PRO: No

! This unit can play back files in the USB por-

table audio player/USB memory that is

USB Mass Storage Class. However, copy-

right protected files that are stored in

above-mentioned USB devices cannot be

played back.

! You cannot connect a USB portable audio

player/USB memory to this unit via a USB

hub.

WAV

! Compatible format: Linear PCM (LPCM),

MS ADPCM

! File extension: .wav

! Quantization bits: 8 and 16 (LPCM), 4 (MS

ADPCM)

! Sampling frequency: 16 kHz to 48 kHz

(LPCM), 22.05 kHz to 44.1 kHz (MS AD-

PCM)

! Partitioned USB memory is not compatible

with this unit.

! Depending on the kind of USB portable

audio player/USB memory you use, this

unit may not recognize the USB audio

player/USB memory or audio files may not

be played back properly.

! Do not leave the USB portable audio

player/USB memory in direct sunlight for

extended amounts of time. Extended expo-

sure to direct sunlight can result in USB

portable audio player/USB memory mal-

function due to the resulting high tempera-

ture.

Handling guideline and

supplemental information

! There may be a slight delay when starting

playback of audio files encoded with image

data.

Appendix

Additional Information

! Do not leave the USB portable audio

player/USB memory in high temperature.

! Firmly secure the USB portable audio

player/USB memory when driving. Do not

let the USB portable audio player/USB

memory fall onto the floor, where it may be-

come jammed under the brake or accelera-

tor pedal.

! Folder selection sequence or other opera-

tion may be altered depending on the en-

coding or writing software.

! Folder hierarchy is allowed up to eight tiers.

However, a practical hierarchy of folder is

less than two tiers.

! Up to 99 folders on a disc can be played

back.

! Depending on the USB devices connected

to this unit, it may generate noise in the

radio.

! There may be a slight delay when starting

playback of audio files on a USB portable

audio player/USB memory with numerous

folder hierarchies.

The sequence of audio files on

USB memory

For USB portable audio players, the sequence is

different from that of USB memory and de-

pends on the player.

! Do not connect anything other than the

USB portable audio player/USB memory.

! Operations may vary depending on the

kind of USB audio player and a USB mem-

ory.

! 01 to 05 represent assigned folder num-

bers. 1 to 6 represent the playback se-

quence. The user cannot assign folder

numbers and specify the playback se-

quence with this unit.

! Playback sequence of the audio file is the

same as recorded sequence in the USB de-

vice.

! To specify the playback sequence, the fol-

lowing method is recommended.

1 Create the file name including numbers

that specify the playback sequence (e.g.,

001xxx.mp3 and 099yyy.mp3).

Example of a hierarchy

: Folder

: Compressed audio file

2 Put those files into a folder.

3 Record the folder containing files into the

USB device.

However, depending on the system environ-

ment, you cannot specify the file playback

sequence.

! Up to 15 000 files on a USB portable audio

player/USB memory can be played back.

! Up to 500 folders on a USB portable audio

player/USB memory can be played back.

! Up to eight tiers directory on a USB porta-

ble audio player/USB memory can be

played back.

Level 1

Level 2 Level 3 Level 4

The sequence of audio files on

the disc

! This unit assigns folder numbers. The user

cannot assign folder numbers.

Appendix

Additional Information

notice

WMA

Windows Media and the Windows logo are tra-

demarks or registered trademarks of Microsoft

Corporation in the United States and/or other

countries.

MP3

Supply of this product only conveys a license

for private, non-commercial use and does not

convey a license nor imply any right to use

this product in any commercial (i.e. revenue-

generating) real time broadcasting (terrestrial,

satellite, cable and/or any other media), broad-

casting/streaming via internet, intranets and/

or other networks or in other electronic con-

tent distribution systems, such as pay-audio or

audio-on-demand applications. An indepen-

dent license for such use is required. For de-

tails, please visit

http://www.mp3licensing.com.

iTunes

iTunes is a trademark of Apple Inc., registered

in the U.S. and other countries.

Appendix

Additional Information

Specifications

Maximum amount of memory

..................................................... 250 GB

Minimum amount of memory

General

..................................................... 256 MB

USB Class ................................... MSC (Mass Storage Class)

File system .................................. FAT16, FAT32

MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3

WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11 (2ch

audio)

(Windows Media Player)

WAV signal format .................. Linear PCM & MS ADPCM

(Non-compressed)

Rated power source ............... 14.4 V DC

(allowable voltage range:

12.0 V to 14.4 V DC)

Grounding system ................... Negative type

Max. current consumption

..................................................... 10.0 A

Dimensions (W × H × D):

DIN

Chassis ..................... 178 mm × 50 mm × 165

Nose ........................... 188 mm × 58 mm × 15 mm

FM tuner

Frequency range ...................... 87.5 MHz to 108.0 MHz

Usable sensitivity ..................... 11 dBf (0.7 μV/75 W, mono,

S/N: 30 dB)

Chassis ..................... 178 mm × 50 mm × 165

Nose ........................... 170 mm × 48 mm × 15 mm

Weight .......................................... 1.3 kg

Signal-to-noise ratio ............... 72 dB (IEC-A network)

AM tuner

Frequency range ...................... 531 kHz to 1 602 kHz (9 kHz)

530 kHz to 1 640 kHz (10

Audio

Maximum power output ....... 50 W × 4

Continuous power output ... 22 W × 4 (50 Hz to 15 000

Hz, 5% THD, 4 W load, both

channels driven)

kHz)

Usable sensitivity ..................... 25 μV (S/N: 20 dB)

Signal-to-noise ratio ............... 62 dB (IEC-A network)

Load impedance ...................... 4 W (4 W to 8 W allowable)

Preout max output level ....... 2.0 V

Tone controls:

Infrared remote control

Wavelength ................................. 940 nm 50 nm

Output ........................................... typ; 12 mw/sr per Infrared

LED

Bass

Frequency ................ 100 Hz

Gain ............................ 13dB

Mid

Frequency ................ 1 kHz

Gain ............................ 12 dB

Treble

Note

Specifications and the design are subject to mod-

ifications without notice due to improvements.

Frequency ................ 10 kHz

Gain ............................ 12 dB

CD player

System .......................................... Compact disc audio system

Usable discs .............................. Compact disc

Signal-to-noise ratio ............... 94 dB (1 kHz) (IEC-A net-

work)

Number of channels .............. 2 (stereo)

MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3

WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11 (2ch

audio)

(Windows Media Player)

WAV signal format .................. Linear PCM & MS ADPCM

(Non-compressed)

USB

Specification .............................. USB 2.0 full speed

Supply current .......................... 500 mA

PYLE Audio View Series PLTV64R User Manual
Pioneer Speaker TS A4674R User Manual
Pioneer DEH 63UB User Manual
Olympus CAMEDIA C 160 User Manual
Marantz 541110333221M User Manual
Kodak KLIC 7006 User Manual
KitchenAid Blender W10457226A_ENv4 User Manual
Kenwood KDC W4537UG User Manual
JVC KS FX742R User Manual
JVC KD LH3150 User Manual