1.2
Electric-, Magnetic- and
1
Important
Electromagnetic Fields ( EMF )
1
Philips Electronics manufactures and sells
many products targeted at consumers, which,
like any electronic apparatus, in general
have the ability to emit and receive electro
magnetic signals.
1.1
Hearing safety
Danger
To avoid hearing damage limit the time you use
the headphones at high volume and set the
volume to a safe level.The louder the volume
the shorter is the safe listening time.
ꢀ
One of Philips leading Business Principles
is to take all necessary health and safety
measures for our products, to comply with
all applicable legal requirements and to stay
well within the EMF standards applicable at
the time of producing the products.
Philips is committed to develop, produce
and market products that cause no adverse
health effects.
Philips confirms that if its products are
handled properly for their intended use,
they are safe to use according to scientific
evidence available today.
Be sure to observe the following
guidelines when using your headphones.
•
•
•
•
Listen at reasonable volumes for reasonable
periods of time.
Be careful not to adjust the volume
continuously upwards as your hearing adapts.
Do not turn up the volume so high that you
can’t hear what’s around you.
You should use caution or temporarily
discontinue use in potentially hazardous
situations.
ꢁ
4
5
Philips plays an active role in the
development of international EMF and safety
standards, enabling Philips to anticipate
further developments in standardization for
early integration in its products.
•
•
Using this headset with both ears covered
while driving is not recommended and may
be illegal in some areas while driving.
For your safety avoid distractions from
music or phone calls while in traffic or other
potentially dangerous environments.
ꢁ
1.3
General maintenance
1.5
Remove the integrated battery
To avoid damage or malfunction:
If in your country there is no collection /
•
•
•
Do not expose the headset to excessive heat. recycling system for electronic products you
Do not drop your headset.
Do not allow your headset to be submerged
in water.
Do not use any cleaning agents containing
alcohol, ammonia, benzene, or abrasives.
If cleaning is required use a soft cloth, if
necessary dampened with a minimum amount
of water or diluted mild soap, to clean the
product.
can protect the environment by removing
and recycling the battery before disposing the
headset. Please take the battery to a battery
collection and recycling location.
•
Removing the battery will destroy the product.
Make sure the headset is disconnected from the
USB charging cable before removing the battery.
About operating and storage
temperatures
You can remove the battery by completing the
following steps.
1
•
Do not operate or store in a place where
temperature is below -15ºC (5ºF) or above
55ºC (131ºF) as this may shorten your
battery life.
Tear off the ear cushion of the left earshell.
Remove the screws that hold the speaker
ꢀ
plate in place.
Remove the speaker plate.
Cut the battery wires.
Remove the battery.
ꢁ
4
5
1.4
Disposal of your old product
Your product is designed and
manufactured with high quality
materials and components, which can
be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product, it means the product is
covered by the European Directive 2002/96/EC.
Please be informed about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old product with your
normal household waste.The correct disposal
of your old product will help prevent potential
negative consequences to the environment and
human health.
4
1.6
Notice for the European Union
Hereby, Philips Consumer Lifestyle, BG P&A,
declares that this Philips Bluetooth headset
SHB9000 is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC.
Check the root folder of your user manual CD
or an addendum sheet for the Declaration of
Conformity.
1.7
Trademarks
Trademarks are the property of Koninklijke
Philips Electronics N.V. or their respective
owners.The Bluetooth word mark and logos are
owned by the Bluetooth SIG, Inc. and any use
of such marks by Koninklijke Philips Electronics
N.V. is under license.
5
2
What’s in the box:
SHB9000
Bluetooth headset
USB charging cable
Quick start guide
CD with user manual
Pouch
Audio cable
3
What else you’ll need:
4
What you can do with
your headset
A mobile phone that is capable of Bluetooth
stereo streaming, i.e. that is compatible with the
Bluetooth A2DP profile.
With your Philips headset you can:
•
•
•
•
•
Lead wireless hands-free conversations
Wirelessly listen to music
Wirelessly control music
Switch between calls and music
Listen to music on devices without Bluetooth
support using the included audio cable
Other devices (Notebooks, PDA’s, Bluetooth
adapters, MP3 players etc.) are also compatible if
they share the Bluetooth profiles supported by
the headset.These profiles are:
For wireless handsfree communication:
•
The Bluetooth headset profile (HSP) or the
Bluetooth Handsfree profile (HFP).
For wireless stereo listening:
•
The Bluetooth Advanced Audio Distribution
profile (A2DP).
For wireless music control:
•
The Bluetooth AudioVideo Remote Control
profile (AVRCP).
The headset features BluetoothVersion 2.0
but will also work with devices featuring other
Bluetooth versions that support the profiles
above.
ꢂ
5
Overview of your Bluetooth stereo headset
LED
indicator
light
Adjustable
headband
Microphone
Audio jack
Mini USB
charging jack
ꢃ
6.2
Pair your headset with your mobile
phone
6
Get started
Your Bluetooth stereo headset must be paired
to your mobile phone before connecting and
using it for the first time with your phone.
“Pairing” will establish a unique encrypted link
between your mobile phone and your headset.
6.1
Charge your headset
Before you use your headset for the first time,
charge the battery for 6 hours for optimum
battery capacity and lifetime.
Pairing has to be done
Warning
•
before using your headset with your mobile
phone for the very first time, or
Use only the original USB charging cable. Using
another charger may damage or destroy your
headset.
Plug the USB charging cable into your
computers USB socket and connect the charger
cable to the headsets charging socket.
•
after pairing more than 2 Bluetooth devices
with your headset. Your headset can store up
to 2 paired devices in its memory, if you pair
more than 2 devices the oldest paired device
is overwritten.
•
“Pairing” is different from “connecting” as
pairing typically only has to be done once,
whereas the phone and headset need to
“connect” every time one of the two devices
was turned off or out of range.
Caution
Finish your call before charging the headset, as
connecting the headset for charging will cut an
ongoing call.
During recharging the LED indicator will show
a red light.The LED will turn off once charging
is complete.Typically a full charge will take
four hours.You can operate the headset during
charging.
ꢄ
To pair your headset with your
mobile phone
Make sure the headset is charged, your mobile
phone is turned on and its Bluetooth feature is
enabled. Check your phones user guide to learn
how to turn on Bluetooth on your phone.
1
With the headset turned off, press
until the LED starts blinking red and blue
alternately. The headset will remain in
“pairing mode” for 5 minutes.
ꢀ
Pairing typically involves a few simple steps
outlined below, please check your phones
user guide for details.
10:35
10:36
10:37
Settings
Connectivity
Settings
Settings
Connectivity
Bluetooth
Devices Found
Enter Password
****
Add
Bluetooth
device
Philips SHB9000
0000
Select
Select
Back
Select
Back
Back
ꢁ
Access a menu on your mobile phone
typically called “Setup”,“Settings”,
“Bluetooth” or “Connectivity”. Select the
option to discover or search for Bluetooth
devices. After a few seconds your phone
should indicate that it has found the “Philips
SHB9000”.
Upon selecting the “Philips SHB9000” on
your mobile phone typically you will need
to confirm the pairing and enter a passcode.
Please enter the headsets passcode “0000”
(four zeros).
4
After successful pairing, the headset will connect
to the mobile phone.You will hear a long beep
to confirm successful pairing and the headsets
LED will change from flashing red/blue to
periodically flashing blue every three seconds.
ꢅ
7
Using your Bluetooth
stereo headset
7.1
Connecting to your mobile phone
Turn on the headset by pressing until the LED
lights up. Once turned on the headset will re-
connect automatically to the last device it was
connected with. If the last connected device is
not available the headset tries to reconnect to
the penultimate device that was connected to
the headset.
If you turn the mobile phone or its Bluetooth
feature on after turning on the headset connect
the headset from your mobile phones Bluetooth
menu.
7.2
Automatic power saving
If your headset cannot find any Bluetooth device
to connect to in range within five minutes it will
automatically power down to save battery life.
7.3
Operating your headset
To control the headset you
tap, hold and double tap the
headsets buttons. A “tap”,
“hold” and “double tap”
differs in the duration and
speed of the button press.
1sec
10
The table below shows how to operate your headset:
In order to:
Do this:
Sound and LED indicator
feedback
Enter pairing mode
Turn headset on
Press until the LED starts
blinking red / blue alternately
Alternating red/blue flash
Press for 2 seconds
• 3x red flash: battery is low
• 2x red flash: > 25% of
charge remaining.
• 1x blue flash: > 50% of
charge remaining.
Turn headset off
Play / Pause music
Stop music
Hold for min. 4 sec
One long beep
Tap
Hold
Skip Fwd/Bwd
FullSound
Tap
or
Hold and
for 4 sec.
simultaneously
One short beep: On
Two short beeps: Off
Adjust volume
Tap VOL- or VOL+
Pick up a call / End a call
Tap
Pick up a 2nd call / put other call Tap
on hold / switch back*
Reject a call
Hold
One long beep
Two short beeps
One short beep
Redial the last number
Activate voice dialing*
Mute Mic
Double tap
Hold until “beep” sound
Double tap (during call)
Short beep every five
seconds until mute is turned
off.
Transfer call to phone*
Other status indicators:
Hold
One short beep
Connected to Bluetooth device Blue light flashes every 3 seconds.
(while in standby or while
listening to music)
Ready for pairing
In pairing mode, LED light flashes continuously alternating red
and blue.
On but not connected
In call
Blue light flashing fast.
While call is ringing, blue light flashes fast (twice per second).
After call pick up, slows down to once per second.
Low battery
LED will flash red instead of blue. A short double beep will
be heard every minute with five minutes or less of talk time
remaining.
* Available if supported by your mobile phone
11
7.4
Wearing your
Bluetooth stereo headset
The headband is fully adjustable to customize
the fit to your liking.The soft slow recovery
foam cushions provide excellent sound sealing
and long lasting listening comfort.
You can twist the earshell on its hinge for single-
sided listening for DJ mixing and monitoring.
Flat-fold the headphone by twisting both
earshells and put it into the travel pouch for
transport.
1ꢀ
ꢄ.ꢀ
Learn about the battery status
8
Using more of your
Immediately after turning the headset on, the
LED will indicate the battery status.
Bluetooth stereo headset
LED behaviour
3x red blinking
Battery status
ꢄ.1
Use with the audio cable
Less than 25% battery
remaining
You can use your headset with non-Bluetooth
enabled devices or on airplanes (in which the
use of Bluetooth may be restricted) by taking
advantage of the headsets audio jack. Corded
operation does not require battery power
for music listening.The microphone and the
FullSound digital sound enhancement will not
work via the audio cable.
2x red blinking
1x blue blinking
Less than 50% of charge
remaining
50% or more of charge
remaining
The LED will continuously flash red with about 5
minutes of talk time remaining.You will also hear
two short beeps every minute to remind you to
end the call or transfer it to your phone before
the battery runs out.
Finish your call before connecting the audio
jack, as this will switch off battery power and cut
an ongoing call.
Connect one end of the included audio cable to
the headsets audio jack and the other end to the
music devices headphone jack.
Mini USB
charging jack
1ꢁ
ꢄ.4
Learn about FullSound
ꢄ.ꢁ
Learn about simultaneous use for
voice and audio
FullSound is a smart digital sound enhancement
algorithm, which runs on a powerful processor
inside your Bluetooth headset.
Your Bluetooth stereo headset can connect to
•
one Bluetooth audio device (supporting the
A2DP and AVRCP Bluetooth profile) and
one Bluetooth communication device
(supporting HFP or HSP Bluetooth profile) at
the same time.
It restores and enhances bass, treble, stereo
effects and dynamics of compressed music
and leads to a more natural,“real life” sound
experience based on years of acoustic research
and tuning.
•
Therefore you can connect your Bluetooth
stereo headset.
The FullSound feature decreases music playing
time by less than 10% if activated. The feature
is activated when you buy the product, to
•
with a Bluetooth stereo enabled phone to
both listen to music and lead calls, or
with a Bluetooth phone that does not
support Bluetooth stereo (A2DP) to lead
calls and at the same time to a Bluetooth
audio device (Bluetooth enabled MP3 player,
Bluetooth audio adapter etc.) to listen to
music. Make sure to pair the phone first
with your Bluetooth headset, then turn both
the phone and headset off to then pair the
Bluetooth audio device.
•
turn FullSound off or on hold
and
simultaneously for 4 seconds.You will hear one
short beep after turning FullSound on, and two
short beeps after turning FullSound off.
Tip
The FullSound feature is available during wireless
operation, not while using the audio jack.
With the SwitchStream feature you can listen to
music and monitor your calls at the same time.
Even while listening to music, you will hear a ring
tone when receiving a call and can switch to the
call simply by tapping the button.
14
9
Technical data
•
Up to 17 hours of playtime or 18 hours of
talk time
•
•
•
Up to 400 hours of standby time
Typical time for a full charge: 4 hours
Rechargeable Lithium-Polymer battery
(460mAh)
•
Bluetooth 2.0+EDR, Bluetooth stereo
support (A2DP – Advanced Audio
Distribution Profile,AVRCP – AudioVideo
Remote Control Profile), Bluetooth mono
support (HSP – Headset Profile, HFP
– Hands-Free Profile)
•
•
•
FullSound digital sound enhancement
Digital echo & noise reduction
3.5mm audio jack for corded headphone
mode
•
•
•
Adjustable, flat folding headband.
Noise isolating slow recovery foam.
Operating range up to 15 meters (50 feet)
Specifications are subject to change without
notice.
15
10 Frequently asked questions
Audio quality when streaming from phone
is very low or audio streaming does not
work at all.
Bluetooth headset does not switch on.
Battery is very low.
Charge your Bluetooth headset.
Phone may not be A2DP compatible and only
support (mono) HSP/HFP.
Check your phones compatibility.
Bluetooth headset does not switch on.
Audio cable is connected.
Unplug the audio cable.
Audio quality is poor and crackling noises
can be heard.
Bluetooth audio source is out of range.
Reduce the distance between the headset and
the Bluetooth audio source, or remove obstacles
between them.
No connection to mobile phone.
Bluetooth disabled.
Enable Bluetooth on your mobile phone and turn
the headset on after turning on the phone.
I hear but cannot control the music on my
device (e.g. skip forward / backward).
Bluetooth audio source does not support
AVRCP.
Mobile phone cannot find headset.
• The headset may be connected to another
previously paired device.
Turn the currently connected device off or
move it out of range.
Check the user manual of your audio source.
• Pairings may have been reset or headset has
been previously paired with other device.
Start the pairing process as described in this
user manual.
additional support.
Redialing does not work.
Your mobile phone may not support this feature.
Voice dialing does not work.
Your mobile phone may not support this feature.
The headset is connected to a Bluetooth
stereo enabled phone, but music will play
on the phone s speaker only.
Phone may have option to listen to music via
speaker or headset.
Check your phones user guide on how to transfer
the music to the headset.
1ꢂ
2008 © Koninklijke Philips Electronics N.V.
All rights reserved.
|