Operating Instructions
Digital Video Camcorder
Model No.
PV-GS250
Before connecting, operating or adjusting this product,
please read the instructions completely.
Spanish Quick Use Guide is included.
Guía para rápida consulta en español está incluida.
Mini
For USA assistance, please call: 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo
LSQT0862 A
FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
≥Reorient or relocate the receiving antenna.
≥Increase the separation between the equipment and receiver.
≥Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
≥Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, follow the attached installation instructions and use
only shielded interface cables with ferrite core when connecting to computer or peripheral devices.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
Declaration of Conformity
Trade Name:
Model No.:
Panasonic
PV-GS250
Responsible party: Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ 07094
Support Contact: Panasonic Consumer Electronics Company
1-800-211-PANA (7262)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1)This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
CAUTION: TO PREVENT FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE
RECOMMENDED ACCESSORIES ONLY.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE
ONLY WITH THE SAME OR EQUIVALENT TYPE.
≥Since this product gets hot during use, operate it in a well ventilated place; do not install this
equipment in a confined space such as a bookcase or similar unit.
WARNING
AS WITH ANY SMALL OBJECT, SD CARDS CAN BE SWALLOWED BY YOUNG CHILDREN. DO
NOT ALLOW CHILDREN TO HANDLE THE SD CARD.
3
LSQT0862
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or the table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
S3125A
13) Unplug this apparatus during lightning storms or when it will be left unused for
long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
4
LSQT0862
≥AVOID SUDDEN CHANGES IN
Precautions
TEMPERATURE ... If the unit is suddenly
moved from a cold place to a warm place,
moisture may form on the tape and inside the
unit.
USE & LOCATION
WARNING
≥TO AVOID SHOCK HAZARD ... Your
Camcorder and power supply should not be
exposed to rain or moisture. Do not connect the
power supply or operate your Camcorder if it
gets wet. Your Camcorder has been designed
for outdoor use, however it is not designed to
sustain direct exposure to water, rain, sleet,
snow, sand, dust, or a direct splashing from a
pool or even a cup of coffee. This action could
permanently damage the internal parts of your
Camcorder. Do not attempt to disassemble this
unit. There are no user serviceable parts inside.
Unplug your Camcorder from the power supply
before cleaning.
≥DO NOT LEAVE YOUR CAMCORDER OR
THE POWER SUPPLY TURNED ON WHEN
NOT IN USE.
≥STORAGE OF YOUR CAMCORDER ... Store
and handle your Camcorder in a manner that
will not subject it to unnecessary movement
(avoid shaking and striking). Your Camcorder
contains a sensitive pick-up device which could
be damaged by improper handling or storage.
CARE
≥TO CLEAN YOUR CAMCORDER ... Do not use
strong or abrasive detergents when cleaning
your Camcorder body.
≥TO PROTECT THE LENS ... Do not touch the
surface of the lens with your hand. Use a
commercial Camcorder lens solution and lens
paper when cleaning the lens. Improper
cleaning can scratch the lens coating.
≥TO PROTECT THE FINISH OF YOUR
CAMCORDER ... Before handling your
Camcorder, make sure your hands and face are
free from any chemical products, such as
suntan lotion, as it may damage the finish.
CAUTION
≥DO NOT AIM YOUR CAMCORDER AT THE
SUN OR OTHER BRIGHT OBJECTS
≥DO NOT LEAVE THE CAMCORDER WITH
THE EVF AIMED DIRECTLY AT THE SUN AS
THIS MAY CAUSE DAMAGE TO THE
INTERNAL PARTS OF THE EVF
≥DO NOT EXPOSE YOUR CAMCORDER TO
EXTENDED HIGH TEMPERATURE ... Such as,
in direct sunlight, inside a closed car, next to a
heater, etc... This action could permanently
damage the internal parts of your Camcorder.
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited
viewing.
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation,
and is intended for home and other limited viewing uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly is prohibited.
This class B digital apparatus complies with CANADIAN ICES-003.
U.S.A./CANADA CONSUMERS: ATTENTION:
A lithium ion/polymer battery that is recyclable powers the product
you have purchased. Please call 1-800-8-BATTERY for information
on how to recycle this battery.
5
LSQT0862
Before opening the CD-ROM package, please read the following.
End User License Agreement (for USB Driver, Video Stream
Driver and MotionDV STUDIO)
You (“Licensee”) are granted a license for the Software defined in this End User Software Agreement
(“Agreement”) on condition that you agree to the terms and conditions of this Agreement. If Licensee
does not agree to the terms and conditions of this Agreement, promptly return the Software to
Matsushita Electric Industrial Co., Ltd. (“Matsushita”), its distributors or dealers from which you made
the purchase.
Article 1
License
Licensee is granted the right to use the software, including the information recorded or described on the
CD-ROM, instruction manuals, and any other media provided to Licensee (collectively “Software”), but
all applicable rights to patents, copyrights, trademarks and trade secrets in the Software are not
transferred to Licensee.
Article 2
Use by a Third Party
Licensee may not use, copy, modify, transfer or allow any third party, whether free of charge or not, to
use, copy or modify the Software, except as expressly provided for in this Agreement.
Article 3
Restrictions on Copying the Software
Licensee may make a single copy of the Software in whole or in part solely for back-up purpose.
Article 4
Computer
Licensee may only use the Software on a single computer at a single location.
6
LSQT0862
Article 5
Reverse Engineering, Decompiling or Disassembly
Licensee may not reverse engineer, decompile, or disassemble the Software, except to the extent
either of them is permitted under law or regulation of the country where Licensee resides. Matsushita,
or its distributors or dealers will not be responsible for any defects in the Software or damage to
Licensee caused by Licensee’s reverse engineering, decompiling, or disassembly of the Software.
Article 6
Limitation of Liability
The Software is provided “AS-IS” without warranty of any kind, either expressed or implied, including,
but not limited to, warranties of non-infringement, merchantability and/or fitness for a particular
purpose. Further, Matsushita does not warrant that the operation of the Software will be uninterrupted
or error free. Matsushita or any of its distributors or dealers will not be liable for any damage suffered by
Licensee arising from or in connection with Licensee’s use of the Software.
Article 7
Export Control
Licensee agrees not to export or re-export to any country the Software in any form without the
appropriate export licenses under regulations of the country where Licensee resides, if necessary.
Article 8
Termination of License
The right granted to Licensee hereunder will be automatically terminated if Licensee violates any of the
terms and conditions of this Agreement. Upon such automatic termination, Licensee must destroy the
Software and related documentation together with all the copies thereof at Licensee’s own expense.
7
LSQT0862
Contents
Record mode
Parts identification and handling.................... 12
Fitting the lens cap......................................... 14
Power supply ................................................. 16
Charging time and recordable time................ 17
Inserting/removing a cassette........................ 18
Inserting/removing a card .............................. 19
Turning the Camcorder on............................. 20
Selecting a mode........................................... 20
Switching the language.................................. 21
Using the menu screen.................................. 22
Setting date and time..................................... 23
Adjusting LCD monitor/viewfinder.................. 23
Using the remote control................................ 24
Magic Wire Remote Control with Narration
Fade in/fade out function............................... 34
Using the built-in flash ................................... 35
Recording in various situations
Mic............................................................... 26
(Scene mode) ............................................. 37
Recording in natural colors
(White balance)........................................... 38
Manual focus adjustment .............................. 39
Manual shutter speed/aperture
adjustment .................................................. 40
8
LSQT0862
Menu
Playing back tape .......................................... 41
Slow-motion playback/
frame-by-frame playback ............................ 42
Variable-speed search function ..................... 42
Playback on TV.............................................. 43
Playing back card .......................................... 43
Formatting a card........................................... 45
Protecting files on a card ............................... 45
Writing the printing data on a card
Before requesting repair
Index.............................................................. 87
Spanish Quick Use Guide/
Recording from a tape onto a card ................ 46
Copying onto a DVD recorder or a VCR
(Dubbing) .................................................... 46
Recording the contents of other
Using the DV cable for Recording
Printing pictures by directly connecting to
With a PC
Using the Camcorder with a PC .................... 52
Connecting Computer and Camcorder.......... 53
Using as a Web camera ................................ 53
Using MotionDV STUDIO .............................. 56
To disconnect USB cable safely.................... 59
If you no longer need software or driver
(Uninstall).................................................... 60
Notes ............................................................. 60
9
LSQT0862
Before using
3 Push the [PUSH] mark 1 in order to close
the cassette holder.
Quick Guide
ª Charging the battery
1 Connect the AC main lead to the AC adaptor
and the AC main socket.
2 Put the battery on the battery mount by
aligning the mark, and then securely plug it
in.
1
PUSH
4 Only after the cassette holder is completely
housed, close the cassette cover.
ª Inserting/removing a card
1 Open the LCD monitor and then open the
card slot cover.
ª Fitting the battery
Push the battery against the battery holder and
slide it until it clicks.
2 Insert/remove the card into/from the card
slot.
1
ª Inserting/removing a cassette
1 Slide the [OPEN/EJECT] lever and open the
cassette cover.
≥When inserting a card, face the label side 1
towards you and push it straight in with one
stroke as far as it goes.
≥When removing the card, open the card slot
cover and press the center of the card and
then pull it straight out.
3 Securely close the card slot cover.
ª How to turn on the power
1 While pressing the button 1, set the [OFF/
ON] switch to [ON].
2 After the cassette holder is opened, insert/
remove the cassette.
1
10
LSQT0862
Before using
ª How to turn off the power
ª Playing back tape
≥Set to Tape Playback Mode.
1 While pressing the button 1, set the [OFF/
ON] switch to [OFF].
1
1 Operate with joystick.
ª Recording on a tape
≥Set to Tape Recording Mode.
1/;: Playback/Pause
6: Rewind/Review playback (Reverts to
playback with the 1/; icon.)
5: Fast forward/Cue playback (Reverts to
playback with the 1/; icon.)
1 Press the recording start/stop button to
start recording.
∫:
Stop
ª Playing back card
≥Set to Picture Playback Mode.
2 Press the recording start/stop button again
to pause recording.
;
1 Operate with joystick.
ª Recording still pictures onto a card
(Photoshot)
≥Set to Card Recording Mode.
E:
Plays back the previous picture.
Plays back the next picture.
PC
D:
1/∫: Slide show (Plays back the still pictures
on the card in order) start/stop
1 Press the [PHOTO SHOT] button
PHOTO
SHOT
11
LSQT0862
Before using
Parts identification and handling
Before using
Accessories
ª Camcorder
The following are the accessories supplied with
this product.
(1)
(5)
1)
(2)
(3)
(6)
(7)
PV-DAC14D
K2GJ2DZ00017
K2CA2CA00025
(4)
2)
5)
8)
3)
CR2025
4)
(8)
(9)
(1) Built-in flash -35-
(2) Recording lamp -64-
(3) Microphone (built-in, stereo) -32-, -34-
(4) Grip belt
(One-touch free style grip belt) -15-
(5) Lens (LEICA DICOMAR)
≥LEICA is a registered trademark of Leica
microsystems IR GmbH and DICOMAR is a
registered trademark of Leica Camera AG.
(6) White balance sensor -39-
(8) Lock button -15-
CGA-DU12
VYF2992
N2QAEC000012
N2QCBD000030
7)
6)
VFC3506-1A
K2KC4CB00018
VFA0425B
1) AC adaptor, DC cable, AC cable -17-
(9) Lock cover -15-
(13)
CAUTION:
This unit will operate on 110/120/220/240 V
AC. An AC plug adaptor may be required for
voltages other than 120 V AC. Please
contact either a local or foreign electrical
parts distributor for assistance in selecting
an alternate AC plug. We recommend using
outlets.
AV
/
Ë
(10)
(11)
REMOTE/MIC
(10) Audio-video input/output terminal [AV]
-46-
≥Use the supplied AV cable or headphones
only, otherwise audio may not be played
back normally.
2) Battery pack -16-
3) Remote control, button-type battery -24-
4) Magic wire remote control with narration
mic -26-
5) Lens cap -14-
6) AV cable -46-
Headphone terminal [Ë]
(11) Terminal for Magic Wire Remote Control
with Narration Mic [REMOTE] -26-
Microphone terminal [MIC]
can be used as an external microphone.
≥When the Camcorder is connected with AC
Adaptor, sometimes noise may be heard
depending on microphone type. In that
case, please switch to battery for power
supply and noise will stop.
7) Shoulder strap -14-
8) USB cable and CD-ROM -51-
(12) USB terminal [ ] -51-
(13) Speaker -41-
12
LSQT0862
Before using
(17)
(18)
(28) Reset button [RESET] -68-
(29) Power LCD button [POWER LCD] -24-
Power LCD lamp -24-
(19)
(20)
(14)
(30) Mode select switch [AUTO/MANUAL/
FOCUS] -27-, -37-, -40-
(31) Card access lamp -19-
(32) DV terminal [DV] -48-
(33) Card slot cover -19-
(15)
(16)
(21)
(22)
(23)
(24)
(34) Card slot -19-
S-VIDEO
(36)
(14) Viewfinder -16-, -77-
(37)
Due to limitations in LCD production
(38)
(39)
technology, there may be some tiny bright or
dark spots on the viewfinder screen.
However, this is not a malfunction and does
not affect the recorded picture.
(35)
(35) Cassette holder -18-
(36) Cassette eject lever [OPEN/EJECT] -18-
(37) Cassette cover -18-
(38) Zoom lever [W/T] -31-
Volume lever [s /VOLr] -41-
(39) Photoshot button [PHOTO SHOT] -29-
(15) Battery holder
(18) Power lamp -20-
(19) Quick start recording button
Quick start recording lamp -32-
(20) Menu button [MENU] -22-
(21) Joystick -20-
(22) Mode dial -20-
(23) Recording start/stop button -28-
-43-
(40)
1
(28)
(29)
(25)
(26)
(27)
(40) Smart accessory shoe
(30)
(31)
The stereo zoom microphone/VW-VMH3
(optional) or the video DC light/VW-LDH3
(optional) should be mounted here.
≥When using an accessory for the smart
accessory shoe, the power is supplied from this
product.
(32)
(33)
(34)
≥When mounting or removing the accessory,
extend the viewfinder (1).
(25) Focus ring -39-
(26) LCD monitor -15-, -77-
Due to limitations in LCD production
technology, there may be some tiny bright or
dark spots on the LCD monitor screen.
However, this is not a malfunction and does
not affect the recorded picture.
13
LSQT0862
Before using
1
2
(43)
(43) Lens hood
In order to remove the lens hood, rotate it
counter-clockwise 1. In order to fit it, put into slot
2, and then rotate it clockwise.
(41)
(41) Tripod receptacle
Fitting the lens cap
This is a hole for attaching the Camcorder to
optional tripod. (Please carefully read the
operating instructions for how to attach the tripod
to the Camcorder.)
≥When the tripod is used, operate the Camcorder
from the Magic Wire Remote Control with
Narration Mic for convenience. (When not using
the remote control, attach the clip to the grip belt
for convenience. When you move with remote
control attached to a pocket, etc., take care to
avoid tipping over the tripod.)
Fit the lens cap to protect the surface of the lens.
1 Remove the grip belt. Run the end of the
lens cap cord through the hole in the grip
belt attachment and run the lens cap
through the lens cap cord.
≥You cannot open the card slot cover when the
tripod is used. Insert the card first and then
attach the tripod.
≥The lens cap removed can be attached to the
lens cap fixture. (It cannot be hung if the grip
belt is used as a hand strap.)
(42)
(42) Shoulder strap fixture
3
1
2
≥To fit or remove the lens cap, hold both sides of
the lens cap with the tips of your finger and
thumb.
≥Put the strap through the fixture 1 and through
the stopper 2 so it will not come off. Extend
part 3 by at least 1 inch (2 cm).
≥Fit the other end of the belt similarly.
14
LSQT0862
Before using
ª To use as a grip belt
Adjust the belt length so it fits your hand.
The one-touch free-style grip belt
1 Adjust the belt length and the pad position.
ª To use as a hand strap
If you use the grip belt as a hand strap, then you
can carry or handle this Camcorder more easily.
1 Open the lock cover 1 by pinching the
projections 2 on both sides. Press the lock
button 3 to remove the grip belt.
2
2
3
1
1 Flip the belt.
2 Adjust the length.
3 Fix the belt.
1
3
≥When removing the grip belt, tightly hold the
Camcorder with both hands.
≥After removing the grip belt, restore the lock
cover to the original position.
Using the LCD monitor
You can record the image while viewing it on the
LCD monitor.
2 Adjust the belt length.
1 Put a finger on the LCD monitor release and
pull the LCD monitor out in the direction of
the arrow.
1
2
3
1
1 Flip the belt.
2 Slide 1 in the direction indicated by the arrow.
3 Fix the belt.
3 Put your hand through the strap.
≥The viewfinder is now deactivated.
≥It can open up to 90o.
2 Adjust the angle of the LCD monitor
according to your preference.
≥Use the Magic Wire Remote Control with
Narration Mic for more convenience.
≥Hold the Camcorder without covering the
microphones or the sensors with your hands.
1 180o
2 90o
≥It can rotate up to 180o 1 towards the lens or
90o 2 towards the viewfinder.
ª To restore the strap to the grip belt
≥When returning the grip belt to the grip belt
attachment, press the lock cover 1 and check if
the grip belt is securely locked.
≥The brightness and color level of the LCD
monitor can be adjusted from the menu.
≥If it is forcibly opened or rotated, the Camcorder
may be damaged or fail.
≥Check that the card slot cover is closed.
≥When the LCD monitor is rotated by 180o
towards the lens (when recording yourself), the
LCD monitor and the viewfinder will be
simultaneously activated.
1
15
LSQT0862
Before using
Using the viewfinder
Power supply
ª Extending the viewfinder
1 Pull out the viewfinder and extend it by
pulling the extension knob.
ª Charging the battery
When this product is purchased, the battery is not
charged. Charge the battery before using this
product.
≥Battery charging time (-17-)
≥We recommend using Panasonic batteries.
≥If you use other batteries, we cannot guarantee
the quality of this product.
≥If the DC input lead is connected to the AC
adaptor, then the battery will not charge.
Remove the DC input lead from the AC adaptor.
1 Connect the AC cable to the AC adaptor and
the AC jack.
2 Put the battery on the battery mount by
aligning the mark, and then securely plug it
in.
ª Lifting up the viewfinder
1 Lift it up by pinching the viewfinder
extension knob.
ª Adjusting the field of view
1 Adjust the focus by sliding the eyepiece
corrector knob.
ª Charging lamp
Lights up: Charging
Goes off: Charging completed
Flashing: The battery is over discharged
(discharged excessively). In a while,
the lamp will light up and normal
charging will start.
When the battery temperature is
excessively high or low, the [CHARGE]
lamp flashes and the charging time will
be longer than normal.
12:30:45PM
OCT 15 2005
12:30:45PM
OCT 15 2005
≥You can adjust the brightness of the viewfinder
from the menu.
16
LSQT0862
Before using
ª Connecting to the AC outlet
Charging time and recordable time
The times shown in the table below show the
times at a temperature of 68oF (25oC) and a
humidity of 60%. This is just a guide. If the
temperature is higher or lower than the specified
value, the charging time will become longer.
Supplied
battery/
CGA-DU12
(7.2 V/
A
B
2 h. 25 min.
2 h. 5 min.
(1 h. 55 min.)
1
1150 mAh)
CGA-DU21
(7.2 V/
2040 mAh)
CGR-DU06
(7.2 V/
A
B
3 h. 55 min.
3 h. 30 min.
(3 h. 15 min.)
1 h. 40 min.
1 h. 5 min.
(1 h.)
1 Connect the AC cable to the AC adaptor and
the AC jack.
2 Connect the DC cable to the AC adaptor.
3 Connect the DC cable to this product.
≥Lift up the viewfinder beforehand.
≥The output plug of the AC cable is not
completely connected to the AC adaptor jack.
As shown in 1, there is a gap.
≥Do not use the power cord for other
equipment since the power cord is exclusively
designed for this Camcorder. Do not use the
power cord from other equipment for this
Camcorder.
A
B
640 mAh)
A Charging time
B Maximum continuously recordable time
“1h. 10 min.” indicates 1 hour 10 minutes.
≥The battery CGA-DU12 is supplied.
≥The times shown in the table are rough
estimates. The times indicate the recordable
time when the viewfinder is used. The times in
parentheses indicate the recordable time when
the LCD monitor is used.
≥We recommend the Battery Pack CGA-DU12
and CGA-DU21 for long recording time (2 hour
or more for continuous recording, 1 hour or
more for intermittent recording).
ª Fitting the battery
Push the battery against the battery holder and
slide it until it clicks.
≥The recordable time will become shorter in the
following cases:
≥When you use both the viewfinder and the
LCD monitor simultaneously while rotating
the LCD monitor frontward to record yourself,
0 Lux MagicPix function, etc.
≥When you use this Camcorder with the LCD
monitor lit up by pressing the [POWER LCD]
button.
ª Removing the battery
While pushing the [PUSH BATT] button, slide the
battery (or the DC input lead) to remove it.
≥When you use accessories fitted on the
Camcorder’s smart accessory shoe such as
the stereo zoom microphone and video DC
light, etc..
≥The batteries heat up after use or charging. The
Camcorder being used will also heat up. This is
normal.
PUSH
BATT
≥Along with the reduction of the battery capacity,
the display will change: r # s #
t # u # v. If the battery
discharges, then u (v) will flash.
≥Hold the battery with your hand so it does not
fall.
17
LSQT0862
Before using
ª When the cassette holder does not
Inserting/removing a cassette
come out
1 Slide the [OPEN/EJECT] lever and open the
cassette cover.
≥Close the cassette cover completely, and then
open it again completely.
≥Check if the battery has run down.
ª When the cassette holder cannot be
housed
≥Set the [OFF/ON] switch to [OFF], then to [ON]
again.
≥Check if the battery has run down.
≥When the cover is fully opened, the cassette
holder will come out.
2 After the cassette holder is opened, insert/
remove the cassette.
ª Inserting/removing the cassette
≥When the cassette holder is in motion, do not
touch anything except the [PUSH] mark.
≥When inserting a previously recorded cassette,
use the blank search function to find the position
where you want to continue recording. If you
overwrite-record on a previously recorded
cassette, be sure to find the position where you
want to continue recording.
≥Close the cassette cover tightly.
≥When closing the cassette cover, do not get
anything, such as a cable, caught in the cover.
≥When inserting a cassette, orient it as shown
in the figure, and then securely insert it as far
as it goes.
≥When removing, pull it straight out.
3 Push the [PUSH] mark 1 in order to close
the cassette holder.
ª Accidental erasure prevention
If the accidental erasure prevention slider 1 of a
cassette is opened (slide in the direction of the
[SAVE] arrow), the cassette cannot be recorded.
When recording, close the accidental erasure
prevention slider of the cassette (slide in the
direction of the [REC] arrow).
1
PUSH
1
4 Only after the cassette holder is completely
housed, close the cassette cover.
R
E
C
SAVE
≥After using, make sure to rewind the cassette
completely, remove it, and put it in a case. Store
the case in an upright position. (-76-)
≥When condensation is formed on the lens or the
main unit of the Camcorder, even if no
condensation alarm is indicated, condensation
may have formed on the heads or the cassette
tape. Do not open the cassette cover. (-73-)
18
LSQT0862
Before using
ª Card access lamp
Inserting/removing a card
Before inserting/removing a card, be sure to turn
the power [OFF].
≥If the card is inserted or removed with the power
turned on, this Camcorder may malfunction or
the data recorded on the card may be lost.
1 Open the LCD monitor and then open the
card slot cover.
≥When the Camcorder accesses the card
(reading, recording, playback, erasing, etc.), the
access lamp lights up.
≥If the following operations are performed when
the access lamp is lit, then the card or the
recorded data may be damaged or the
Camcorder may malfunction.
≥Opening the card slot cover and inserting or
removing the card
≥Operating the [OFF/ON] switch or the mode
dial
2 Insert/remove the card into/from the card
slot.
ª SD Memory Card
≥The memory capacity indicated on the SD
Memory Card label corresponds to the total
amount of capacity to protect and manage the
copyright and the capacity available as
conventional memory for a Camcorder,
personal computer or other equipment.
1
ª Concerning the write protection
switch on the SD Memory Card
≥The SD Memory Card has a write protection
switch on it. If the switch is moved to [LOCK],
you cannot write to the card, erase the data on
it, or format it. If it is moved back, you can
perform those functions.
≥When inserting a card, face the label side 1
towards you and push it straight in with one
stroke as far as it goes.
≥When removing the card, open the card slot
cover and press the center of the card and
then pull it straight out.
3 Securely close the card slot cover.
ª Concerning the card
≥Do not touch the terminals on the back of the
card.
≥Do not format the card with another Camcorder
or any personal computer. This operation may
make the card unusable.
≥Electrical noise, static electricity, or failure of the
Camcorder or the card may damage or erase
the data stored on the card. We recommend
saving important data on a personal computer
by using a USB cable, PC card adaptor, or USB
reader/writer.
19
LSQT0862
Before using
Turning the Camcorder on
How to use the joystick
When the Camcorder is turned on with the lens
cap fitted, the automatic white balance
adjustment may not function properly. Please turn
the Camcorder on after removing the lens cap.
ª Basic joystick operations
Operations on the menu screen and selection
of files to be played back on the multi-image
display
Move the joystick up, down, left, or right to select
an item or file, and then push in the center to set
it.
ª How to turn on the power
1 While pressing the button 1, set the [OFF/
ON] switch to [ON].
≥The power lamp lights up.
1
3
5
1
4
2
1 Select by moving up.
2 Select by moving down.
3 Select by moving left.
4 Select by moving right.
5 Push the center to select the item.
ª How to turn off the power
1 While pressing the button 1, set the [OFF/
ON] switch to [OFF].
≥The power lamp goes off.
ª Joystick and screen display
Push the center of the joystick, and icons will be
displayed on the screen. Each push switches the
display as follows depending on the mode.
(In the Tape playback mode or the Picture
playback mode, the icons will be automatically
displayed on the screen.)
1
Selecting a mode
1) Tape recording mode
Rotate the mode dial to select the desired mode.
1 Rotate the mode dial.
≥Set your desired mode to 1.
([AUTO/MANUAL/FOCUS] switch is set to
[AUTO])
1
Screen
display OFF
Joystick
3
4
2
1
3
4
Tele-macro
-34-
-33-
-34-
-33-
-33-
-29-
: Tape recording mode
Use this when you want to record the image on a
tape. (Also, you can simultaneously record still
pictures on a card while recording images on a
tape.)
Soft skin mode
Fade
Backlight compensation
MagicPix/0 Lux MagicPix
Recording check
: Tape playback mode
Use this to play back a tape.
: Card recording mode
Use this to record still pictures on a card.
: Picture playback mode
Use this to play back the still pictures recorded on
a card.
: PC mode
You can view or edit the images recorded on a
PC
card on your personal computer.
20
LSQT0862
Before using
2) Tape recording mode
5) Card recording mode
([AUTO/MANUAL/FOCUS] switch is set to
[MANUAL])
([AUTO/MANUAL/FOCUS] switch is set to
[MANUAL])
Screen
display OFF
Screen display
OFF
4
White balance
Shutter speed
Iris or gain value
Select/Adjust
-38-
4
White balance
Shutter speed
Iris or gain value
Select/Adjust
-38-
1
2
-38-
-38-
1
2
-38-
-38-
Select/Adjust
Select/Adjust
6) Picture playback mode
3) Tape playback mode
Screen
display OFF
Screen
display OFF
3
4
2
1
Playback/stop
Erase
-43-
-44-
-43-
-43-
3
4
2
1
Playback/pause
Stop
-41-
-41-
-41-
-41-
Playback previous picture
Playback next picture
Rewind (review playback)
Fast forward (cue playback)
4) Card recording mode
([AUTO/MANUAL/FOCUS] switch is set to
[AUTO])
Switching the language
You can switch the language on the screen
display or the menu screen.
Screen
display OFF
3
4
1
Tele-macro
-34-
-33-
-33-
Soft skin mode
Backlight compensation
21
LSQT0862
Before using
7 Press the joystick to determine the setting.
Using the menu screen
For each individual menu, please refer to -62-.
1 Press the [MENU] button.
MENU
ª To exit the menu screen
Press the [MENU] button.
≥The menu corresponding to the mode
selected by the mode dial is displayed.
≥Do not switch the mode dial when the menu is
displayed.
ª To get back to the previous screen
Move the joystick left.
2 Move the joystick up or down in order to
select the top menu.
ª About the menu setting
≥The menu screen does not appear during
recording. And you cannot record when the
menu screen appears.
ª Operating with remote control
The menu screen transition is the same as when
the buttons on the main unit are used.
1 Press the [MENU] button.
3 Move the joystick right or press it to set the
selection.
VAR.
MENU
SEARCH
ENTER
4 Move the joystick up or down in order to
select the sub-menu.
2 Select a menu item.
≥Use the direction buttons (π, ∑, ∏, ∫) and
[ENTER] button in place of the joystick on the
main unit.
VAR.
MENU
SEARCH
ENTER
5 Move the joystick right or press it to set the
selection.
3 Press the [MENU] button, to exit the menu
screen.
VAR.
MENU
SEARCH
6 Move the joystick up or down in order to
select the item to be set.
ENTER
22
LSQT0862
Before using
Setting date and time
Adjusting LCD monitor/viewfinder
If the screen shows the incorrect date/time, then
adjust it.
≥Set to Tape Recording Mode or Card
Recording Mode.
ª Adjusting the brightness and color
level
1 Set [SETUP] >> [LCD SET] or [EVF SET] >>
[YES].
1 Set [BASIC] >> [CLOCK SET] >> [YES].
2 Move the joystick up or down in order to
select the item to be adjusted.
[LCD SET]
2 Move the joystick left or right in order to
select the item to be set. Then move the
joystick up or down to set the desired value.
≥The year will change as follows:
:
Brightness of the LCD monitor
2000, 2001, ..., 2089, 2000, ...
≥The 12-hour clock is used.
3 Press the joystick to determine the setting.
≥The clock function starts at [00] seconds.
:
Color level of the LCD monitor
[EVF SET]
Brightness of the viewfinder
:
EVF
ª About date/time
3 Move the joystick left or right to move the
bar indication representing the brightness.
4 Press the [MENU] button or the joystick to
complete the settings.
≥The date and time function are driven by a
built-in lithium battery.
≥Make sure to check the time before recording
because the built-in clock is not very accurate.
≥In order to adjust the brightness of the
viewfinder, close the LCD monitor, and the
viewfinder will be activated.
≥When the LCD monitor is rotated by 180°
towards the lens, the brightness of the LCD
monitor cannot be adjusted.
ª Recharging the built-in lithium battery
≥If [0] or [--] is indicated when the Camcorder is
turned on, then the built-in lithium battery has
run down. Connect the AC adaptor to the
Camcorder or place the battery on the
Camcorder, and the built-in lithium battery will
be recharged. Leave the Camcorder as is for
approx. 24 hours, and the battery will drive the
date and time for approx. 6 months. (Even if the
[OFF/ON] switch is set to [OFF], the battery is
still being recharged.)
≥These settings will not affect the images actually
recorded.
23
LSQT0862
Before using
ª In order to increase the brightness of
Using the remote control
the entire LCD monitor
ª Remote control
Using the remote control supplied will enable
control of almost all functions of this Camcorder.
1 Press the [POWER LCD] button.
POWER LCD
(1)
START/
STOP
DATE/ PHOTO
OSD
TIME
SHOT
(2)
ZOOM
T
(3)
(4)
≥The [POWER LCD] lamp lights up.
≥If the [POWER LCD] button is pressed, the
entire LCD monitor will become approx. twice
as bright as the normal.
¥REC A.DUB
V
W
FF/
/REW PLAY
W
VOL
STILL ADV PAUSE STILL ADV
STOP
VAR.
MENU
SEARCH
≥Press this button again, and the lamp will go off
and the brightness will revert back to the original
brightness.
ENTER
(5)
≥This will not affect the images to be recorded.
≥If you turn on the Camcorder when the AC
adaptor is used, the [POWER LCD] function will
automatically be activated.
(1) Date/time button [DATE/TIME] -62-
(2) On-screen display button [OSD] -43-
(3) Record button [¥REC] -47-, -48-
(4) Audio dubbing button [A.DUB] -49-
(5) Direction buttons [π, ∑, ∏, ∫] -22-
ª Changing the picture quality on the
LCD monitor
1 Set [SETUP] >> [LCD AI] >> [DYNAMIC] or
[NORMAL].
START/
STOP
DATE/ PHOTO
OSD
TIME
SHOT
[DYNAMIC]: The image on the LCD monitor
becomes clear and vivid. Optimum
contrast and brightness are set
depending on the scenes recorded.
Clear and brilliant images are
presented. (The effect will vary
depending on the images
ZOOM
T
¥REC A.DUB
V
W
FF/
/REW PLAY
(7)
W
VOL
STILL ADV PAUSE STILL ADV
STOP
(6)
(8)
(9)
VAR.
MENU
SEARCH
ENTER
recorded.)
[NORMAL]: Switches to the standard picture
quality.
(6) Slow/frame-by-frame forward button
[E, D] (E: reverse, D: forward) -42-
(7) Zoom/volume button [ZOOM/VOL] ¢
(8) Search button [VAR. SEARCH] -42-
(9) Menu button [MENU] -22-
≥The effect will vary depending on the scene
recorded.
≥The picture quality on the viewfinder will not be
affected.
≥This function is automatically set to [DYNAMIC]
when the brightness of the LCD monitor is
increased (when the [POWER LCD] lamp lights
up) and cannot be set to [NORMAL]
independently.
START/
STOP
DATE/ PHOTO
(10)
(14)
OSD
TIME
SHOT
ZOOM
T
(15)
(16)
¥REC A.DUB
V
W
FF/
/REW PLAY
W
≥This will not affect the images to be recorded.
≥When the LCD monitor is rotated by 180°
towards the lens, the picture quality of the LCD
monitor is temporarily adjusted as if the
[LCD AI] is set to [NORMAL].
(11)
(12)
(13)
VOL
STILL ADV PAUSE STILL ADV
STOP
VAR.
MENU
SEARCH
(17)
ENTER
(10) Photoshot button [PHOTO SHOT] ¢
(11) Rewind/review button [6]
(12) Pause button [;]
(13) Stop button [∫]
24
LSQT0862
Before using
(14) Recording start/stop button [START/
STOP] ¢
ª Remote control usable range
(15) Playback button [1]
(16) Fast forward/cue button [5]
(17) Enter button [ENTER] -22-
¢ means that these buttons function in the same
manner as the corresponding buttons on the
Camcorder.
ª Install a button-type battery
Install the button-type battery supplied in the
remote control before using it.
1 While pressing the stopper 1, pull out the
battery holder.
≥The distance between the remote control and
the Camcorder: Within approx. 15 feet (5 m)
Angle: Approx. 10o up and 15o down, left, and
right
ª Selecting the remote control mode
If 2 Camcorders are used simultaneously, set the
mode for one pair of Camcorder and remote
control to [VCR1] and that of the other pair to
[VCR2]. This will prevent interference between
the 2 pairs. (The default setting is [VCR1]. When
the button-type battery is replaced, the setting will
revert to the default [VCR1].)
1
2 Set the button-type battery with its (i) mark
facing upward and slide the battery holder
back into place.
1 Setting on the Camcorder:
Set [SETUP] >> [REMOTE] >> [VCR1] or
[VCR2].
2 Setting on the remote control:
VOL
STILL ADV PAUSE STILL ADV
Warning
Danger of explosion if battery is
2
1
STOP
incorrectly replaced.
Replace only with the same or equivalent
type recommended by the equipment
manufacturer. Discard used batteries
according to manufacturer’s instructions.
Risk of fire, explosion and burns. Do not
recharge, disassemble, heat above 212°F
(100°C) or incinerate. Keep the Button-
Type battery out of the reach of children.
Never put Button-Type battery in mouth.
If swallowed, call your doctor.
[VCR1]:
Press [D] and [∫] simultaneously. 1
[VCR2]:
Press [E] and [∫] simultaneously. 2
ª Concerning the button-type battery
≥
When the button-type battery runs down, replace
it with a new battery (part number: CR2025). The
battery is normally expected to last about 1 year,
but it depends on operation frequency.
≥Keep the button-type battery out of the reach of
children.
Replace battery with Panasonic PART NO.
CR2025 only. Use of another battery may
present a risk of fire or explosion.
Caution: Battery may explode if mistreated.
Dispose of used battery promptly. Keep
away from children.
≥If the remote control mode of the Camcorder
and that of the remote control do not match with
each other, “REMOTE” will appear. When the
remote control is operated for the first time after
the Camcorder is turned on, “CHECK REMOTE
MODE” (-67-) will appear and operation is
impossible. Set the same remote control mode.
≥The remote control is intended for indoor
operation. Outdoors or under strong light, the
Camcorder may not operate properly even
within the usable ranges.
Do not recharge, disassemble or dispose of
in fire.
≥Within a 3 feet (1 m) range, you can operate the
remote control using the remote control sensor
on the LCD monitor side of the Camcorder.
25
LSQT0862
Before using
ª Switching the microphone
Magic Wire Remote Control with
Narration Mic
Press the [TALK] button on the Magic Wire
Remote Control with Narration Mic, and the
microphone on the remote control will be
activated instead of that on the Camcorder.
This controller can be used from different high
and low angles. It is also handy when a tripod is
used. When you do not use the controller, attach
the clip to the grip belt. Left-handed users can use
this Camcorder more easily.
(1)
(2)
(3)
≥While this button is being pressed, [ ] appears
and the microphone on the remote control is
activated.
≥We recommend you talk with the microphone
approx. 4 inches (10 cm) away from your
mouth.
(4)
(5)
(1) Microphone [MIC]
(2) Recording start/stop button [REC]
(3) Zoom lever [W/T]
ª About the clip (on the backside)
(4) Photoshot button [PHOTO SHOT]
(5) Microphone switch button [TALK]
ª Connect the Magic Wire Remote
Control with Narration Mic to the
Camcorder
1 Plug the Magic Wire Remote Control with
Narration Mic into the [REMOTE] terminal
as far as it goes.
When you move with the clip fitted to your pocket
or elsewhere, beware of knocking over the tripod
or causing the Camcorder to fall off the table.
REMOTE/MIC
≥The [PHOTO SHOT] button on the Magic Wire
Remote Control with Narration Mic cannot be
pressed halfway.
≥If the pin plug of the control is not inserted
securely into the [REMOTE] terminal as far as it
will go, normal operation may not be ensured.
≥Before using, make sure that the plug is
inserted securely into the terminal as far as it
will go.
26
LSQT0862
Record mode
ª About auto mode
Record mode
≥Set the [AUTO/MANUAL/FOCUS] switch to
[AUTO], and color balance (white balance) and
focusing will be adjusted automatically.
≥Auto white balance: -78-
Check before recording
Check the following by a trial recording before
important events such as weddings in order to
verify that the image recording and audio
recording work properly and that you know how to
use the Camcorder.
≥Auto focusing: -78-
≥Color balance and focus may not be adjusted
manually adjust the white balance and focus.
ª Basic Camcorder holding
AUTO
MANUAL
1)
FOCUS
≥Scene mode setting (-37-)
≥White balance setting (-38-)
≥Shutter speed setting (-40-)
≥Iris/gain value setting (-40-)
≥Focus setting (-39-)
2)
4)
ª Recording mode
You can switch the tape recording mode.
≥Set to Tape Recording/Playback Mode.
1 Set [BASIC] or [ADVANCE] >> [REC SPEED]
>> [SP] or [LP].
If the LP mode is selected, the recording time will
be 1.5 times the SP mode, but some functions will
be disabled.
3)
≥We recommend using the SP mode for
important recording.
5)
≥In order to fully exhibit the performances of the
LP mode, we recommend using Panasonic
cassettes marked LP mode.
≥It is not possible to dub audio onto images
recorded in the LP mode. (-49-)
1) Hold the Camcorder with both hands.
2) Run your hand through the grip belt.
3) Do not cover the microphones or sensors with
your hands.
≥In the LP mode, the picture quality will not be
degraded in comparison with the SP mode, but
mosaic noise may appear on the playback
image or some functions may be disabled.
≥Playback on other digital video equipment
or on digital video equipment without the LP
mode
4) Keep your arms near your body.
5) Slightly open your legs.
≥When you are in the open air, record pictures
with the sunlight as far in the background as
possible. If the subject is backlit, it will become
dark in the recording.
ª Check points
≥Remove the lens cap. (-14-)
≥Playback of the image on other digital video
equipment recorded in the LP mode
≥Slow/frame-by-frame playback
adjustment may not function properly. Please
turn the Camcorder on after removing the lens
cap.)
≥Grip belt adjustment (-15-)
≥Power supply (-16-)
≥Insert a cassette/card. (-18-, -19-)
≥Setting date/time (-23-)
≥Adjustment of LCD monitor/viewfinder (-23-)
≥Getting the remote control ready (-24-)
≥Setting SP/LP mode (-27-)
27
LSQT0862
Record mode
ª On-screen display in the tape
recording mode
Recording on a tape
≥Remove the lens cap. (-14-)
(When the Camcorder is turned on with the lens
cap fitted, the automatic white balance
adjustment may not function properly. Please
turn the Camcorder on after removing the lens
cap.)
1)
0h00m10s00f
R 0:30
2)
≥Set to Tape Recording Mode.
3)¢
100
4)¢
5)¢
¢These indications are displayed only when the
card is inserted.
1) Recording time elapsed
2) Remaining tape indication
3) Still picture size
1 Press the recording start/stop button to
start recording.
4) Number of recordable still pictures
(When no picture can be recorded, this
indication will flash in red.)
2 Press the recording start/stop button again
to pause recording.
5) Quality of still pictures
ª Concerning the remaining tape time
indication on the screen
≥The remaining tape time is indicated in minutes.
(When it reaches less than 3 minutes, the
indication starts flashing.)
;
≥During a 15-second or shorter recording, the
remaining tape time indication may not be
displayed or the remaining tape time may not be
displayed correctly.
≥For details on the recording time on a tape, refer
to -17-.
≥In some cases, the remaining tape time
indication may display remaining tape time that
is 2 to 3 minutes shorter than the actual
remaining tape time.
≥Carry out a recording check (-29-) to verify that
the image is recorded properly.
≥In order to find the unrecorded section, carry out
the blank search (-29-).
ª [POWER SAVE]
[OFF]:
When 5 minutes passes without
any operation, the standby mode
will be automatically set. In the
standby mode, [;] blinks and it
takes more time than usual to start
recording after you press the
recording start/stop button.
[5 MINUTES]: When 5 minutes passes without
any operation, the Camcorder
automatically turns off to protect
the tape or to prevent the battery
from running down. When you
want to use the Camcorder, turn it
on again.
≥The Camcorder cannot be automatically turned
off when you connect the USB connection cable
or the DV cable with the Camcorder or when the
Camcorder is in the PC mode.
28
LSQT0862
Record mode
Recording still pictures on a card
Check the recording
while recording image onto a tape
The last image recorded is played back for 2 to
3 seconds. After checking, the Camcorder will be
set to a recording pause.
≥Set to Tape Recording Mode.
1 Press the joystick during the recording
pause until the icon 1 appears.
You can record still pictures while recording
image onto a tape.
≥Set to Tape Recording Mode.
1 Press the [PHOTO SHOT] button fully while
recording image onto a tape.
2 Move the joystick down to select the
recording check icon [ ].
PHOTO
SHOT
1
≥For the number of still pictures to be recorded
on a card, refer to -80-.
≥When recording pictures onto a card, the
recording start/stop button is disabled.
≥You can select a picture quality for still pictures
to be recorded. (-31-)
≥In tape recording mode, the size of pictures that
can be recorded is [640].
≥In order to record higher quality still pictures,
you must use the card recording mode.
≥If the wide mode is used, you cannot record
images onto the card.
Blank search function
Searches for the last part of the image recorded
(unused part of the tape).
≥Set to Tape Recording/Playback Mode.
1 Set [BASIC] or [ADVANCE] >>
[BLANK SEARCH] >> [YES].
ª Stopping a blank search midway
through
Move the joystick down.
≥The [PHOTO SHOT] button does not work if it is
pressed halfway.
≥If the cassette tape has no blank part, then the
Camcorder will stop at the end of the tape.
≥The Camcorder stops at a point approx.
1 second before the end of the last image
recorded. When you start recording at that
point, the image can be recorded seamlessly
from the last image.
29
LSQT0862
Record mode
your arms stationary at your side so as not to
Recording still pictures onto a card
(Photoshot)
shake the Camcorder.
≥You can record stable pictures without shaking
by using a tripod and the remote control.
≥Set to Card Recording Mode.
PC
≥For the number of still pictures to be recorded
on a card, refer to -80-.
≥The sound cannot be recorded.
≥While data is being recorded on a card, do not
operate the mode dial.
1 Press the [PHOTO SHOT] button halfway in
order to adjust focusing. (For auto focusing
only)
≥If you set [EIS] to [ON], then the image
stabilizer function will be more effective.
(MEGA Optical image stabilizer will be
indicated.)
≥When the access lamp is lit, do not insert or
remove a card.
≥Another product may degrade or not play back
data recorded on this Camcorder.
≥If set [PICT. QUALITY] >> [
], mosaic-pattern
noise may appear on a playback image
depending on the picture content.
≥The iris/gain value is fixed and this
Camcorder focuses on the subject
automatically.
≥When the [PICTURE SIZE] is set to other than
[640], the mega pixel recording mode is set.
≥When the picture size setting is other than [640],
the scene around the subject can be recorded
wider than that in [640].
PHOTO
SHOT
ª On-screen display in the card
recording mode
1
2
1
Shutter chance mark
1)
± (The white lamp flashes.):
Focusing
¥ (The green lamp lights up.):
When in focus
100
2)
3)
No mark:
When focusing is unsuccessful
≥The shutter chance mark is indicated as follows
when the [PHOTO SHOT] button is not pressed
halfway. Please use it as a guide for recording.
¥ (The green lamp lights up.):
When in focus and a good picture
can be recorded
1) Still picture size
2) Number of recordable still pictures
(When no pictures can be recorded, the red
light will flash.)
3) Quality of still pictures
ª Progressive Photoshot
± (White lamp lights up.):
You can record still pictures with higher picture
quality and frames. (You cannot switch the
progressive function off/on.)
Almost in focus
Focus area
2 Press the [PHOTO SHOT] button fully.
2
ª To record still pictures clearly
≥When zooming in on the subject with a
magnification of 4k to 10k or higher, it is
difficult to reduce the slight shaking from holding
the Camcorder by hand. We recommend
decreasing the zoom magnification and
approaching the subject when recording.
≥When recording still pictures, hold the
Camcorder firmly with your hands and keep
≥In the tape recording mode, the progressive
function may be disabled depending on the
other functions used. (-69-)
30
LSQT0862
Record mode
ª Select the size of still pictures to be
Zoom in/out function
recorded on a card
1 Set [BASIC] >> [PICTURE SIZE] >> select
the desired picture size.
[2048]: 2048k1512
You can zoom in up to 10k optically.
≥Set to Tape/Card Recording Mode.
1 Wide-angle recording (zoom out):
Push the [W/T] lever towards [W].
Close-up recording (zoom in):
[1600]: 1600k1200
[1280]: 1280k960
[640]: 640k480
Push the [W/T] lever towards [T].
VOL
ª Select the picture quality for
photoshot images
1 Set [BASIC] >> [PICT. QUALITY] >> select a
desired picture quality.
W
T
[
[
]: High picture quality
]: Normal picture quality
T
1tW
≥You can also change the picture quality on
[ADVANCE] >> [PICT. QUALITY] in the tape
recording mode.
5tW
T
10tW
T
ª Recording with a shutter operation
effect
You can add a shutter operation simulating
sound.
1 Set [ADVANCE] >> [SHTR EFFECT] >> [ON].
≥When zooming in and taking a picture while
holding the Camcorder by hand, we recommend
using the image stabilizer function.
≥When you are zooming on a faraway subject, a
sharper focus is achieved if the recording
subject is 3.9 feet (1.2 m) or further from the
Camcorder.
≥When the zoom speed is high, the subject may
not be focused easily.
≥When the zoom magnification is 1k, the
Camcorder can focus on a subject approx.
1.6 inches (4 cm) distant from the lens.
ª About the shutter chance mark
≥The shutter chance mark does not appear in
manual focus mode.
≥When the subject is not easily focused, focus on
the subject manually.
≥You can record still pictures on the card even if
the shutter chance mark does not appear, but
pictures may be recorded without being
focused.
≥The shutter chance mark does not appear or
has difficulty displaying in the following
cases.
≥When the zoom magnification is high.
≥When the Camcorder is shaken.
≥When the subject is moving.
≥When the subject stands in front of a light
source.
ª Digital zoom function
If the zoom magnification exceeds 10 times, then
the digital zoom function will be activated. The
digital zoom function allows you to select a
magnification from 25k to 700k.
1 Set [ADVANCE] >> [D.ZOOM] >> [25k] or
[700k].
≥When close subjects and far subjects are
included in the same scene.
25tW
T
≥When the scene is dark.
≥When there is a bright part in the scene.
≥When the scene is filled with only horizontal
lines.
[OFF]:
[25k]:
[700k]: Up to 700k
Optical zoom only (Up to 10k)
Up to 25k
≥When the scene lacks contrast.
ª Concerning the focusing area
≥When there is a contrasting object ahead or
behind the subject in the focus area, the subject
may not be focused. Move the contrasting
object out of the focus area.
≥The larger the digital zoom magnification, the
more the image quality is degraded.
≥When the Card Recording mode is used, the
digital zoom function cannot be used.
31
LSQT0862
Record mode
ª To use the zoom microphone function
Quick start
Interlocked with the zooming operation, the
microphone will clearly capture sounds far away
with the tele-shot or those in the vicinity with the
wide-angle shot.
This Camcorder will be put into standby in
approx. 1.7 seconds after the power is turned on.
≥This is only activated in the following cases.
≥A tape or a card is inserted, while the Tape
Recording Mode is set.
≥Set to Tape Recording Mode.
1 Set [ADVANCE] >> [ZOOM MIC] >> [ON].
≥A card is inserted, while the Card Recording
Mode is set.
ZOOM
1 Press the [QUICK START] button.
QUICK
START
ª About the variable speed zoom
function
≥When pushing the [W/T] lever as far as it will go,
you can zoom from 1k to 10k in 1.0 second at
the maximum.
≥The zoom speed varies according to the amount
of movement of the [W/T] lever.
≥For the Magic Wire Remote Control with
Narration Mic, the zoom speed changes in
2 stages.
≥The quick start recording lamp lights up.
(Press the button again to cancel it.)
2 Set the [OFF/ON] switch to [OFF].
≥The variable speed zoom function cannot be
used with the remote control.
≥The quick start is now ready.
Recording yourself
3 Set the [OFF/ON] switch to [ON].
≥
This Camcorder will be put into a recording
You can record yourself while viewing the LCD
monitor. You can record persons in front of the
Camcorder while showing them the image. The
image is horizontally flipped as if you see a mirror
image. (The image to be recorded is the same as
that recording.)
pause in approx. 1.7 seconds after it is turned on.
ª To cancel the quick start when the
power is [OFF]
Press and hold the [QUICK START] button for
approx. 2 seconds. The lamp will go off and the
Camcorder will be completely turned off.
≥If the standby continues for approx. 30 minutes,
then the lamp will go off and the Camcorder will
be completely turned off.
1 Rotate the LCD monitor towards the lens
side.
≥When you rotate the mode dial or remove the
battery, the quick start recording lamp is turned
off and the quick start mode is canceled. If the
Camcorder is turned on and the Tape/Card
Recording Mode is set though, the lamp turns
on and the quick start mode is restored.
≥When the LCD monitor is opened, the
≥
When the Camcorder is quick-started with the
white balance on automatic, it may take some
time until the white balance is adjusted if the
scene being recorded has a light source different
from the scene last recorded. (When the
viewfinder will be automatically turned off. If the
LCD monitor is rotated towards the lens side
though, then the viewfinder will be activated.
≥When the LCD monitor is rotated towards the
lens side, the icon will not be displayed even if
you push the center of the joystick.
MagicPix function is used, however, the white
balance of the scene last recorded is retained.)
≥The zoom magnification differs from when it is in
the quick start standby mode and when the
recording starts.
≥
Since about half the power of normal recording is
used in quick start standby, using quick start reduces
the time during which pictures can be recorded.
32
LSQT0862
Record mode
3 (In the case of 0 Lux MagicPix function)
Rotate the LCD monitor towards the lens
side.
Backlight compensation function
This protects a backlit subject from being
darkened.
≥Set to Tape/Card Recording Mode.
1 Press the joystick until the icon 1 appears.
2 Move the joystick right to select the
backlight compensation icon [ ].
1
ª
≥When the LCD monitor is reversed, the
Power LCD Lamp turns on and the screen is
lit in white.
≥Record the subject while viewing it on the
viewfinder.
≥The image on the screen will become
brighter.
ª To return to normal recording
Select the [ ] icon again.
≥The light of the LCD monitor reaches approx.
3.9 feet (1.2 m) or less.
≥If you operate the [OFF/ON] switch or the mode
dial, the backlight compensation is canceled.
ª To cancel the MagicPix function
Select the MagicPix icon until the MagicPix
indication disappears.
MagicPix functions
This function allows you to record color subjects
in dark locations to stand out against the
background.
Attach the Camcorder to a tripod, and you can
record images free from vibration.
≥Only manual focusing can be used.
≥Recorded scene is seen as if frames were
missed.
≥If set in a bright place, the screen may become
whitish for a while.
≥The MagicPix function makes the signal
charging time of CCD up to approximately 30k
longer than usual, so that dark scenes invisible
to the naked eye can be recorded brightly. For
this reason, bright dots that are usually invisible
may be seen, but this is not a malfunction.
≥The MagicPix function is canceled when you
operate the power switch or the mode dial.
MagicPix function
You can record dark locations brightly in color.
0 Lux MagicPix function
You can record completely dark locations with the
light of the LCD monitor.
≥Set to Tape Recording Mode.
1 Press the joystick until the icon 1 appears.
2 Move the joystick up to select the MagicPix
icon [ ].
Soft skin mode
This allows the skin color to be recorded in a
softer tone.
≥Set to Tape/Card Recording Mode.
1 Press the joystick until the icon 1 appears.
2 Move the joystick down to select the soft
skin icon [ ].
1
1
≥Each upward press switches the modes.
OFF # MagicPix function # 0 Lux MagicPix
function # OFF
ª To cancel the soft skin mode
Select the [ ] icon again.
≥If the background or anything else in the scene
has colors similar to the skin color, they will also
be softened.
≥If the brightness is insufficient, the effect may
not be clear.
33
LSQT0862
Record mode
Start recording. (fade in)
Tele-macro function
When you start recording, the image/audio
disappears completely and the image/audio
gradually appears.
By focusing only on the subject and blurring the
background, the image can be impressive. This
Camcorder can focus on the subject at a distance
of approx. 16 inches (40 cm).
≥Set to Tape/Card Recording Mode.
1 Press the joystick until the icon 1 appears.
2 Move the joystick up to select the
tele-macro icon [ ].
Pause recording. (fade out)
The image/audio gradually disappears. After the
image/audio completely disappears, recording
stops.
1
≥If the magnification is 10k or less, then it is
automatically set to 10k.
ª To cancel the tele-macro function
Select the [ ] icon again.
≥If a sharper focus cannot be achieved, adjust
the focus manually.
≥In the following cases, the tele-macro function is
canceled.
≥The zoom magnification becomes lower than
10k.
≥The [OFF/ON] switch or the mode dial is
operated.
ª To cancel fading
Select the [ ] icon again.
ª To select the color for fade in/out
The color which appears in fading pictures can be
selected.
1 Set [SETUP] >> [FADE COLOR] >> [WHITE]
or [BLACK].
Fade in/fade out function
≥While the fade in/fade out function is selected, it
takes several seconds to display the image
when you start recording images. Besides, it
also takes several seconds to pause recording.
Fade in
The image and audio gradually appear.
Fade out
The image and audio gradually disappear.
≥Set to Tape Recording Mode.
1 Press the joystick until the icon 1 appears.
2 Move the joystick left to select the fade icon
Wind noise reduction function
This reduces the wind noise coming into the
microphone when recording.
≥Set to Tape Recording Mode.
[
].
1 Set [BASIC] >> [WIND CUT] >> [ON].
1
B
3 Press the recording start/stop button.
ª To cancel the wind noise reduction
function
Set [BASIC] >> [WIND CUT] >> [OFF].
≥Reduces the wind noise depending on the wind
strength. (If this function is activated in strong
winds, the stereo effect may be reduced. When
the wind weakens, the stereo effect will be
restored.)
34
LSQT0862
Record mode
ª When the flash is not used
Using the built-in flash
Set [ADVANCE] >> [FLASH] >> [ ].
Use the built-in flash in order to record still
pictures in dark places.
≥Set to Tape/Card Recording Mode.
1 Set [ADVANCE] >> [FLASH] >> [ß] or [ßA].
≥If [ßA] is selected, then the flash will
automatically flash as necessary.
ª To adjust the brightness of the flash
1 Set [ADVANCE] >> [FLASH LEVEL] >>
select the desired brightness level.
[ßj]:
[ßd0]:
[ßi]:
If the brightness is too high ([ßj] or
[ßAj] indication will appear).
In normal recording (the [ß] or [ßA]
indication will appear).
If the brightness is insufficient ([ßi]
or [ßAi] indication will appear.)
2 Press the [PHOTO SHOT] button.
PHOTO
SHOT
ª Red eye reduction function
Reduces the phenomena where human eyes
become red from flashes.
≥The flash is activated and the picture will be
recorded.
1 Set [ADVANCE] >> [RED EYE] >> [ON].
≥You cannot use the built-in flash unless the card
is inserted in the Camcorder.
≥The Camcorder, even when its flash has been
turned off, automatically determines if the flash
is necessary by detecting the ambient
brightness. (If it determines that the flash is
necessary, the [ ] indication lights up in
yellow.)
≥When the [ß] ([ßi]/[ßj]) indication or the [ßA]
([ßAi]/[ßAj]) indication is displayed, the flash
can be lit. If the indication is flashing or not
displayed, the flash cannot be lit.
≥The available range of the flash is approx. 3 to
7.5 feet (1 to 2.5 m) in a dark place. Pictures will
appear dark or reddish when they are recorded
by using the flash at distances greater than
7.5 feet (2.5 m).
≥When set [FLASH] >> [ßA] and the shutter
speed, iris or gain is adjusted, the indication
(either [ßA], [ßAi], or [ßAj]) may disappear
and the flash may not be lighted.
≥Red eye phenomenon may appear depending
on the recording conditions.
ª Using the flash VW-FLH3 (optional)
≥The flash permits still picture recording in a dark
place 7.5 feet (2.5 m) or more distant from the
subject. The available range of the flash is
approx. 3 to 13 feet (1 to 4 m).
≥When the flash becomes ready to flash, the [ß]
indication appears.
≥The optional flash and the built-in flash cannot
be used simultaneously.
≥The brightness of the flash cannot be adjusted.
≥The shutter speed, iris/gain, and white balance
become fixed.
≥Using the flash outdoors or with backlight or
other bright conditions may result in white
blotches (color blotches) on the pictures. If so,
either adjust the iris manually or use the
backlight compensation function, without using
the flash.
≥Using the flash fixes the shutter speed of
1/750 s or faster to 1/500.
≥The picture may become out of focus in a dark
place. If so, adjust the focus manually.
≥The picture may appear dark if flash is lit in front
of a white background.
≥Carefully read the operating instructions for the
flash.
≥Set the flash to [ ] where using a flash is
prohibited.
≥Do not block the flash by hand or any other
means.
35
LSQT0862
Record mode
ª To cancel the Wide/Cinema function
Self-timer recording
Wide Function
You can record still pictures on a card using the
timer.
≥Set to Card Recording Mode.
1 Set [BASIC] >> [SELF TIMER] >> [YES].
2 Press the [PHOTO SHOT] button.
Set [ADVANCE] >> [WIDE] >> [OFF].
Cinema Function
Set [ADVANCE] >> [CINEMA] >> [OFF].
≥When the Wide Function is activated, the
display such as the menu screen or the
operation icon is expanded horizontally.
≥Images played back vary depending on the TV
connected. Please refer to the operating
instructions for your TV.
≥This function does not widen the recording
range.
≥When images are played back on a TV screen,
the date/time indication may be erased in some
cases.
PHOTO
SHOT
≥After the recording lamp and the [
]
indication flashes for approx. 10 seconds,
recording will start. After recording, the
self-timer will be canceled.
≥You cannot press the [PHOTO SHOT] button
half way. Focusing will be carried out with
reference to the focusing frame.
≥Depending on the TV, the picture quality may
deteriorate.
≥When a cinema picture is imported onto a
personal computer, the imported picture may
not be displayed correctly, depending on the
software used.
≥If you use a TV with an aspect ratio of 4:3, we
do not recommend using the wide mode.
(Images are vertically stretched.)
ª To stop the timer midway through
Press the [MENU] button.
≥By operating the [OFF/ON] switch or mode dial,
the self-timer standby mode is canceled.
≥If the RapidFire Consecutive Photoshot
recording is set, the maximum recordable
pictures are recorded.
Optical image stabilizer function
Recording images for wide-screen
TVs
On this model, [EIS] is used as the indication for
Optical Image Stabilizer.
Reduces the jitter caused by hand movement
when recording.
≥Set to Tape Recording Mode.
1 Set [ADVANCE] >> [EIS] >> [ON].
This allows you to record images compatible with
wide-screen TVs.
Wide Function
Images are recorded with a 16:9 aspect ratio.
Cinema Function
EIS
Images are recorded with a black belt appearing
along the top and bottom of the screen so that
they look like theatre movies.
≥Set to Tape Recording Mode.
1 Wide Function
ª To cancel the image stabilizer function
Set [ADVANCE] >> [EIS] >> [OFF].
Set [ADVANCE] >> [WIDE] >> [ON].
Cinema Function
≥When recording still pictures in the Card
Recording mode, pressing the [PHOTO SHOT]
button halfway increases the effect of the image
stabilizer function. (MEGA Optical image
stabilizer)
Set [ADVANCE] >> [CINEMA] >> [ON].
CINEMA
≥When a tripod is used, we recommend that you
turn the image stabilizer function off.
≥In the following cases, the image stabilizer
function may not work effectively.
≥When the digital zoom is used
≥When the Camcorder is shaken greatly
≥When you record a moving subject while
tracking it
36
LSQT0862
Record mode
RapidFire Consecutive Photoshot
Recording in various situations
(Scene mode)
Records still pictures continuously at a certain
interval.
≥Set to Card Recording Mode.
1 Set [BASIC] >> [PICTURE SIZE] >> [640].
2 Set [ADVANCE] >> [BURST MODE] >> [ON].
When you record images in different situations,
this mode automatically sets optimum shutter
speeds and apertures.
≥Set to Tape/Card Recording Mode.
1 Set the [AUTO/MANUAL/FOCUS] switch to
[MANUAL].
AUTO
MANUAL
3 Press and hold the [PHOTO SHOT] button.
FOCUS
PHOTO
SHOT
2 Set [BASIC] >> [SCENE MODE] >> select the
desired mode.
1)
2)
ª To stop RapidFire Consecutive
Photoshot midway through
Release the [PHOTO SHOT] button.
3)
4)
≥You can press the [PHOTO SHOT] button
halfway and then start RapidFire Consecutive
Photoshot. (Focusing is fixed. If the image
stabilizer function is turned on, then MEGA
Optical image stabilizer will be activated.)
≥The Camcorder records up to 10 still pictures at
intervals of 0.5 seconds. If the shutter speed is
manually set to 1/30, then the still pictures can
be recorded at intervals of 0.7 seconds.
≥One more still picture may be recorded after you
release the [PHOTO SHOT] button.
5)
1) [5] Sports mode
≥To record sports scenes or scenes where
there are quick motions
] Portrait mode
≥To make people stand out from the
2)
[
background
≥The flash is not used.
3)
4)
[
] Low light mode
≥To record dark scenes so they are brighter
] Spotlight mode
≥If [SELF TIMER] >> [YES] is set, the Camcorder
records the maximum number of pictures
recordable.
[
≥To record subjects in a spotlight at a party or
≥Intervals between recording pictures may
become longer depending on the card. We
recommend using a Panasonic SD Memory
Card.
theatre
] Surf & snow mode
≥To record images at very bright locations
such as ski slopes and beaches
5)
[
≥When using a card formatted by other
equipment or a card that was recorded and
erased repeatedly, the intervals between
recording pictures may become longer. If so,
back up your important data on a PC, and
format your card with this Camcorder.
37
LSQT0862
Record mode
ª To cancel the scene mode function
Set [BASIC] >> [SCENE MODE] >> [OFF] or set
the [AUTO/MANUAL/FOCUS] switch to [AUTO].
Recording in natural colors
(White balance)
The automatic white balance function may not
reproduce natural colors depending on the scene
or lighting conditions. If so, you can adjust the
white balance manually.
≥Set to Tape/Card Recording Mode.
1 Set the [AUTO/MANUAL/FOCUS] switch to
[MANUAL].
Sports mode
≥For slow-motion playback or playback pause
of recorded pictures, this mode helps
diminish camera shake.
≥During normal playback, the image
movement may not look smooth.
≥Avoid recording under fluorescent light,
mercury light or sodium light because the
color and brightness of the playback image
may change.
≥If you record a subject illuminated with strong
light or a highly reflective subject, vertical
lines of light may appear.
≥If the brightness is insufficient, the sports
mode does not function. The [5] indication
flashes.
AUTO
MANUAL
FOCUS
2 Move the joystick down until the white
balance indication appears. ([
] etc.)
AWB
MNL
AWB
≥If this mode is used indoors, the screen may
flicker.
Portrait mode
≥If this mode is used indoors, the screen may
flicker. If so, change the scene mode setting
to [OFF].
3 Move the joystick left or right in order to
select the white balance mode.
1)
2)
Low light mode
1 AWB
1
≥Extremely dark scenes may not be able to be
recorded finely.
Spotlight mode
3)
4)
1
1
≥If the recording subject is extremely bright,
the recorded image may become whitish and
the periphery of the recorded image
extremely dark.
Surf & snow mode
≥If the subject is extremely bright, the recorded
1) Auto white balance adjustment [
]
AWB
2) Indoor mode (for recording under
incandescent lamps) [
3) Outdoor mode [
4) Manual adjustment mode [
]
]
image may become whitish.
]
ª To restore to the automatic
adjustment
Move the joystick left or right until the [
AWB
]
indication appears. Or, set the [AUTO/MANUAL/
FOCUS] switch to [AUTO].
≥When the Camcorder is turned on with the lens
cap fitted, the automatic white balance
adjustment may not function properly. Please
turn the Camcorder on after removing the lens
cap.
≥When setting both the white balance and the
iris/gain, set the white balance first.
≥Whenever recording conditions change, re-set
the white balance for correct adjustment.
38
LSQT0862
Record mode
ª To set the white balance manually
Manual focus adjustment
Select [
white subject on the entire screen, move the
joystick up to select the [ ] indication.
] in Step 3. Then, while viewing a
If auto focusing is difficult due to the conditions,
then manual focusing is available.
≥Set to Tape/Card Recording Mode.
1 Set the [AUTO/MANUAL/FOCUS] switch to
[MANUAL].
ª About flashing of the [
] indication
When the manual adjustment mode is
selected
≥Flashing indicates that the white balance
previously adjusted is stored. This setting is
stored until the white balance is adjusted again.
When white balance cannot be set in the
manual adjustment mode
≥White balance may not be adjusted properly in
the manual adjustment mode in dark places. If
so, use the auto white balance mode.
During setting in the manual adjustment mode
≥When the setting is completed, it will remain lit.
AUTO
MANUAL
FOCUS
2 Set the [AUTO/MANUAL/FOCUS] switch to
[FOCUS].
AUTO
MANUAL
FOCUS
ª About the white balance sensor
The white balance sensor detects the type of light
source during recording.
MNL
MF
≥Do not cover the white balance sensor during
recording, or it may not function properly.
ª About the black balance adjustment
This is one of the 3CCD system functions that
automatically adjusts the black when the white
balance is set in the manual adjustment mode.
When the black balance is adjusted, the screen
will temporarily be black.
≥The MNL and the manual focus indication [MF]
will be displayed.
3 Rotate the focus ring to adjust the focus.
1
2
3
≥When focused with a wide angle, the subject
may not be in focus when zoomed in. First,
zoom in on the subject, and then focus on it.
1 Black balance adjustment (Flashes.)
2 White balance adjustment (Flashes.)
3 Adjustment completed (Lights up.)
ª To restore to the automatic
adjustment
Set the [AUTO/MANUAL/FOCUS] switch to
[AUTO] or [FOCUS].
39
LSQT0862
Record mode
≥When recording in an extremely bright place,
Manual shutter speed/aperture
adjustment
the color of the screen may change or flicker. If
this happens adjust the shutter speed manually
to 1/60 or 1/100.
Shutter Speed
Adjust it when recording fast-moving subjects.
When recording people outdoors at night, select a
slow shutter speed and use a flash. Both the
subject and the background will become brighter.
Aperture
Manual iris/gain adjustment
≥If the value does not become “OPEN”, you
cannot adjust the gain value.
≥If the gain value is increased, the noise on the
screen increases.
Adjust it when the screen is too bright or too dark.
≥Set to Tape/Card Recording Mode.
1 Set the [AUTO/MANUAL/FOCUS] switch to
[MANUAL].
≥Depending on the zoom magnification, there are
iris values that are not displayed.
ª Shutter speed range
1/60–1/8000 seconds: Tape Recording Mode
1/2–1/2000 seconds: Card Recording Mode
The shutter speed closer to 1/8000 is faster.
AUTO
MANUAL
ª Iris/gain value range
CLOSE (Closed), F16, ..., F1.7,
OPEN (Opened) 0dB, ..., 18dB
Value closer to [CLOSE] darken the image.
Value closer to [18dB] brighten the image.
Values with dB are gain values.
FOCUS
2 Move the joystick down until the shutter
speed indication or aperture value
indication appears.
MNL
ª Card slow shutter mode
≥If the shutter speed is set to 1/2, 1/4, 1/8, or
1/15, then the card slow shutter mode will be
activated.
1
/60
OPEN
OdB
≥If the [OFF/ON] switch or the mode dial is
operated, then the slow shutter mode will be
canceled.
1)
2)
MNL
MNL
1/60
F2.0
0dB
1/1000
≥In the slow shutter mode:
≥The white balance is fixed.
1) Shutter speed
2) (Aperture) Iris/gain value
3 Move the joystick left or right in order to
adjust the shutter speed or aperture.
≥Focus in manually.
≥If the [AUTO/MANUAL/FOCUS] switch is set to
[FOCUS], then the shutter speed will
automatically be set to 1/60 and the subject is
focused in on. After that the previous shutter
speed will be restored. When the subject is
focused on, [MF] flashes.
ª To restore to automatic adjustment
Set the [AUTO/MANUAL/FOCUS] switch to
[AUTO].
Manual shutter speed adjustment
≥Avoid recording under fluorescent light, mercury
light or sodium light because the color and
brightness of the playback image may change.
≥If you increase the shutter speed manually, the
sensitivity lowers and accordingly the gain value
increases automatically, which may increase
the noises on the screen.
≥You may see vertical lines of light in the
playback image of a brightly shining subject or
highly reflective subject, but this is not a
malfunction.
≥If the scene is low in brightness or contrast, the
subject may not be focused in on.
≥While the Camcorder is focusing on the subject,
you cannot operate any control on it with the
exception of [OFF/ON] switch, mode dial,
[AUTO/MANUAL/FOCUS] switch and
[POWER LCD] button.
≥During normal playback, image movement may
not look smooth.
40
LSQT0862
Playback mode
ª To adjust volume
Playback mode
Playing back tape
Adjust the speaker or headphone volume for
playback.
1 Move the [s /VOLr] lever to adjust the
volume.
≥Set to Tape Playback Mode.
VOL
W
T
1 Operate with joystick.
Towards [r]: increases the volume
Towards [s]: decreases the volume
(The closer to [r], the higher the volume.)
≥On the remote control, press the [T] button to
increase the volume or the [W] button to
decrease it.
1/;: Playback/Pause
6: Rewind/Review playback (Reverts to
playback with the 1/; icon.)
5: Fast forward/Cue playback (Reverts to
playback with the 1/; icon.)
≥When the adjustment is completed, the volume
indication will disappear.
≥If you do not hear the sound, check the settings
of [SETUP] >> [12bit AUDIO].
ª Repeat playback
When the tape end is reached, the tape will be
rewound and played back again.
∫:
Stop
≥During cue/review playback, fast-moving
images may show noise as a mosaic.
≥Before and after cue/review playback, the
screen may become blue for a moment or
images may be distorted.
1 Set [ADVANCE] >> [REPEAT PLAY] >> [ON].
≥The [
] indication appears. (In order to
cancel the repeat playback mode, set
[REPEAT PLAY] >> [OFF] or set [OFF/ON]
switch to [OFF].)
≥When you set [USB FUNCTION] >>
[WEB CAM] and then connect the USB
connection cable, the repeat playback mode is
canceled.
ª Settings on the audio
≥If you cannot listen to the desired audio when
playing back a tape, check the settings in
[SETUP] >> [12bit AUDIO].
≥When you record or dub the audio in [12bit] and
set [SETUP] >> [12bit AUDIO] >> [MIX], the
audio will be played back in stereo sound
regardless of the settings in [AUDIO OUT].
41
LSQT0862
Playback mode
ª To return to normal playback
Press the [1] button on the remote control.
Slow-motion playback/
frame-by-frame playback
≥Set to Tape Playback Mode. (Slow-motion
playback can only be performed by using
the remote control.)
Slow-motion playback
≥In the reversed slow-motion playback, the time
code indication may be unstable.
Slow-motion playback
Frame-by-frame playback
If the image is recorded in the SP mode, then it
will be played back at a speed approx. 1/5 the
normal speed.
≥Press and hold the [E] or the [D] button in the
playback pause, and then the images will
continuously be played back frame by frame.
If the image is recorded in the LP mode, then it
will be played back at a speed approx. 1/3 the
normal speed.
1 Press the [E] button or the [D] button on
the remote control.
Variable-speed search function
The speed of cue/review playback can be varied.
(This operation is only available when using
the remote control.)
≥Set to Tape Playback Mode and play back a
tape.
1 Press the [VAR. SEARCH] button on the
remote control.
V
W
FF/
/REW PLAY
W
VOL
STILL ADV PAUSE STILL ADV
STOP
2 Press the [π] or [∫] button up or down to
vary the speed.
≥If the slow-motion playback continues for
approx. 10 minutes or more, then the
playback will automatically stop. (10 minutes
of slow-motion playback is equivalent to
approx. 2 minutes in the SP mode or approx.
3 minutes in the LP mode.)
VAR.
MENU
SEARCH
ENTER
Frame-by-frame playback
1 During playback, press the [;] button on
the remote control.
2 Press the [E] button or the [D] button on
the remote control.
≥The speeds for cue/review playback are 1/5k
(SP mode slow-motion playback only), 1/3k (LP
mode slow-motion playback only), 2k, 5k,
10k, 20k.
ª To return to normal playback
Press the [VAR. SEARCH] button or [1] button
on the remote control.
V
W
FF/
/REW PLAY
W
VOL
STILL ADV PAUSE STILL ADV
STOP
≥Images may be shown in a mosaic-like pattern.
≥The sound is muted during search.
≥This function is canceled when the operation
icon is displayed.
≥Pushing the [s /VOLr] lever towards [T]
(normal direction) or towards [W] (reversed
direction) of this Camcorder during playback
pause also turns into the frame-by-frame
playback. If you keep pushing the lever, then
the images will continuously be played back
frame by frame.
42
LSQT0862
Playback mode
ª To display the on-screen information
Playback on TV
on the TV
Images recorded by this Camcorder can be
played back on a TV.
≥Insert a recorded tape into this Camcorder.
1 Connect the Camcorder to a TV.
The information displayed on the LCD monitor or
the viewfinder (operation icon, time code and
mode indication, etc.), date and time can be
displayed on the TV.
1 Press the [OSD] button on the remote
control.
START/
STOP
DATE/ PHOTO
[VIDEO IN]
AV/
OSD
TIME
SHOT
[S-VIDEO IN]
[AUDIO IN]
≥Press the button again to erase the OSD
information.
1
2
Playing back card
S-VIDEO
≥Set to Picture Playback Mode.
≥Connect the Camcorder and the TV by using
the AV cable 1.
≥If the TV has an S-Video terminal, then also
connect an S-Video cable 2 (optional). An
S-video connection allows you to enjoy a
higher quality image.
2 Turn on this Camcorder and set the mode
dial to the Tape Playback Mode.
3 Select the input channel on the TV.
4 Move the joystick up to select the [1/;]
icon to start playback.
1 Operate with joystick.
≥The image and audio are output on the TV.
5 Move the joystick down to select the [∫]
icon to stop playback.
E:
Plays back the previous picture.
Plays back the next picture.
≥Whenever plugging in the S-Video cable, plug in
the AV cable, too.
D:
1/∫: Slide show (Plays back the still pictures
≥Use the AC adaptor to avoid battery depletion.
≥Depending on your TV, nothing may be shown
even if you correctly connect the Camcorder
with your TV. In this case, set [BASIC] >>
[AV JACK] >> [OUT].
on the card in order) start/stop
≥While the data on a card is playing back, do not
operate the mode dial.
≥When the access lamp is lit, do not insert or
remove a card.
≥It takes time to display the file depending on the
number of pixels of the file.
≥If you attempt to play back file recorded in a
different format or file data is defective, the
whole display becomes bluish and the
“UNPLAYABLE CARD” indication may appear
as a warning.
≥When playing back a file recorded on other
equipment, the date and time display is different
from when it was recorded.
ª If the image or audio from this
Camcorder is not output on the TV
≥Check that the plugs are inserted as far as they
go.
≥Check the connected terminal.
≥If the image does not appear on the TV even if
[BASIC] >> [AV JACK] >> [OUT/Ë] are set,
then set to [OUT]. (-64-)
≥Check the TV’s input setting (input switch).
(For more information, please read the
operating instructions for the TV.)
≥When playing back a picture recorded on other
equipment, its size and that of pictures recorded
by this Camcorder may appear differently.
43
LSQT0862
Playback mode
ª To display multiple playback files
Deleting files recorded on a card
Multiple files on the card (6 files on 1 screen) are
The deleted files cannot be restored.
≥Set to Picture Playback Mode.
1 Move the joystick left or right to select a file
to delete.
displayed.
1 Move the [s /VOLr] lever to switch the
images.
≥You can select a file in the multi-screen display.
After selecting the file, press the joystick and
display the operation icon.
Towards [r]: Full-screen display
(Displays 1 image.)
2 Move the joystick down to select [ ].
Towards [s]: Multi-screen display
(Displays 6 files on 1 screen.)
≥In the multi-screen display,
≥Move the joystick to select a file (The
selected file will be encircled by a yellow
frame) and press it. The selected file is
full-screen displayed.
≥If there are 7 files or more, move the joystick.
The next, or previous multi-screen will be
displayed.
3 Move the joystick up or down in order to
select [DELETE 1 FILE] and then press it.
4 When the confirming message appears,
select [YES] and press the joystick.
≥In order to stop deletion, select [NO].
ª To delete all files
1 Move the joystick down to select [ ].
ª About the compatibility of still
pictures
≥The Camcorder is compliant with the unified
standard DCF (Design rule for Camera File
system) established by JEITA (Japan
Electronics and Information Technology
Industries Association).
≥The file format supported by this Camcorder is
JPEG. (Not all JPEG formatted files will be
played back.)
≥If a non-standard file is played back, the folder/
file name may not be displayed.
≥The Camcorder may degrade or not play back
data recorded or created on another product
and another product may degrade or not play
back data recorded with the Camcorder.
2 Move the joystick up or down in order to
select [ALL FILES] and then press it.
3 When the confirming message appears,
select [YES] and press the joystick.
≥In case of [ALL FILES], the deletion may take
time if there are many files on the card.
≥When “CARD FULL” is shown during recording,
switch to the Picture Playback Mode and then
delete unnecessary files.
≥If there are no files to delete, insert a new card.
≥If files conforming to DCF standard are deleted,
all the data related to the files will be deleted.
ª Deleting still picture files recorded on
a card by other equipment
≥A still picture file (other than JPEG) that cannot
be played back on the Camcorder may be
erased.
Note:
To delete multiple files on the SD Card (selected
files) connect to a PC and use the SD Drive
feature.
44
LSQT0862
Playback mode
Formatting a card
Writing the printing data on a card
(DPOF setting)
Please be aware that if a card is formatted, then
all the data recorded on the card will be erased.
Store important data on a personal computer, etc.
≥Set to Picture Playback Mode.
1 Set [ADVANCE] >> [CARD FORMAT] >>
[YES].
2 When the confirmation message appears,
select [YES] and press the joystick in order
to format the card.
You can write the data of pictures to be printed,
number of copies, and other information (DPOF
data) onto the card.
≥Set to Picture Playback Mode.
1 Set [ADVANCE] >> [DPOF SET] >> [SET].
2 Move the joystick to select a file to be set,
and then press it.
1
≥The number of prints 1 to be set in DPOF is
displayed.
≥In order to stop formatting, select [NO].
3 Move the joystick up or down in order to
select the number of prints and then press
it.
≥You can select from 0 to 999. (Some copies
of the picture can be printed as you set the
number of prints with the printer supporting
DPOF.)
≥Normally, it is not necessary to format the card.
If a message appears even though you insert
and remove the card several times, format it.
≥Cards formatted on other equipment such as
personal computers cannot be used or
recording takes longer than usual. We
recommend formatting your card on this
Camcorder.
≥2 or more files can be set in succession.
ª To complete the settings
Press the [MENU] button.
Protecting files on a card
Files recorded on a card can be locked so that they
may not be deleted by mistake. (Even if the files are
locked, they will be deleted if the card is formatted.)
≥Set to Picture Playback Mode.
1 Set [BASIC] >> [PROTECT] >> [YES].
2 Move the joystick to select a file to be
locked, and then press it.
≥DPOF setting made on another Camcorder may
not be recognised by this Camcorder. Please
perform the DPOF settings on your Camcorder.
ª To set so that all pictures are not
printed
Select [CANCEL ALL] in Step 1.
ª What is DPOF?
DPOF stands for Digital Print Order Format. This
enables the printing information to be added to
the pictures on the card so that it can be used on
a system supporting DPOF.
1
≥[
] Indication 1 appears and the selected
file is locked. Press the joystick again, and
the lock will be canceled.
≥2 or more files can be locked in succession.
ª To complete the settings
Press the [MENU] button.
45
LSQT0862
Edit mode
Copying onto a DVD recorder or a
Edit mode
VCR (Dubbing)
Recording from a tape onto a card
Pictures recorded by the Camcorder can be
stored on a DVD-RAM or other such media. Refer
to the instructions for the recorder.
≥Place a recorded cassette in the Camcorder,
and an unrecorded DVD-RAM or cassette in
the DVD recorder or VCR.
Still pictures can be recorded on a memory card
from scenes that have already been recorded on
a cassette.
≥Set to Tape Playback Mode.
≥Insert a tape which already has recorded
contents and a card.
1 Connect the Camcorder and the recorder.
1 Start playback.
Connecting with the AV cable
2 Pause at the scene you wish to record, and
press the [PHOTO SHOT] button.
[VIDEO IN]
AV/
PHOTO
SHOT
[S-VIDEO IN]
[AUDIO IN]
1
2
≥Audio will not be recorded.
S-VIDEO
≥The size of still pictures recorded on a card
becomes [640]. (This is not mega pixel
still-picture recording.)
≥If you press the [PHOTO SHOT] button without
pausing, blurred pictures may be recorded.
≥For pictures with an aspect ratio of 16:9,
“CHANGE ASPECT TO 4:3” is shown,
indicating that still pictures cannot be recorded.
≥DV input and wide images recorded on a tape
cannot be recorded on a card.
≥Connect the Camcorder and the recorder by
using the AV cable 1.
≥If the recorder has an S-Video terminal, then
also connect an S-Video cable 2 (optional).
An S-video connection allows you to copy a
high quality image.
Connecting with the optional DV cable (Only
for equipment with a DV terminal)
DV
2 Turn on the Camcorder and set to Tape
Playback Mode.
3 Select the input channel on the TV set and
recorder.
4 Move the joystick up to select the [1] icon
to start playback.
≥The image and sound are reproduced.
5 Start recording.
6 Move the joystick down to select the [∫]
icon to stop playback.
7 Stop recording.
46
LSQT0862
Edit mode
≥For more information, refer to the operating
Move the joystick up to start recording.
instructions for your TV set and recorder.
≥When you do not need functional indications or
date and time indications, press the [OSD]
button on the remote control for no indication.
(When you connect the Camcorder and a
recorder with the DV cable, these indications
may not appear.)
Or, while pressing the [¥REC] button on the
remote controller, press the [1] button.
ª When neither image nor sound from
the Camcorder is output to the TV set
≥Check that the plugs are inserted as far as they
go.
≥Check the connected terminal.
≥When no image is presented on the TV even if
set [BASIC] >> [AV JACK] >> [OUT/Ë], set to
[OUT]. (-64-)
¥REC A.DUB
V
W
FF/
/REW PLAY
W
VOL
STILL ADV PAUSE STILL ADV
STOP
Recording on a card:
Press the [PHOTO SHOT] button.
6 Move the joystick of the Camcorder down or
press the [∫] button on the remote
controller to stop recording.
Recording the contents of other
equipment
≥While analog input pictures are being
recorded on a tape or when the Camcorder is
in recording standby mode, the photoshot
recording is disabled.
You can dub the contents of other equipment to a
DV cassette or card, and can record TV
programs.
≥Set to Tape Playback Mode.
1 Connect the Camcorder and other
equipment.
7 Stop playback. (Other equipment)
≥Do not plug or unplug the cable during recording
or the recording may not be completed properly.
≥Carefully read the operating instructions for your
TV set and video equipment.
≥By operating as [SETUP] or [ADVANCE] >>
[AUDIO REC], set the recording sound mode
([12bit] or [16bit]). (-64-)
≥If a picture (bilingual video, etc.) containing main
sound and sub sound has been dubbed, select
the desired sound by [SETUP] >> [AUDIO OUT]
on playback.
AV/
[VIDEO OUT]
[S-VIDEO OUT]
[AUDIO OUT]
≥If a picture containing a copyright protection
signal (copy guard) is recorded, the message
“COPY PROTECTED” appears when recording
it on a tape and the picture is distorted by
mosaic-like patterns at playback.
1
2
S-VIDEO
≥Connect the Camcorder and other equipment
by using the AV cable 1.
≥When wide images are input, the display such
as the menu screen or the operation icon is
expanded horizontally.
≥If the recorder has an S-Video terminal, then
also connect an S-Video cable 2 (optional). It
allows you to record clearer images.
2 Set [BASIC] >> [AV JACK] >> [IN/OUT].
(Camcorder)
≥If, during recording, an operation such as cue
playback or slow motion playback is performed
on external equipment, mosaic-like patterns
may appear on the picture at playback.
≥If pictures are recorded when TV broadcasting
signals are weak or pictures are affected by
noise, they may be distorted or may not even be
played back.
≥If both the S-Video cable and the AV cable are
connected, S-video signal are input
preferentially.
3 Turn the power on and start playback.
(Other equipment)
4 Start recording. (Camcorder)
Recording on a tape:
5 Set [ADVANCE] >> [REC STDBY] >> [ON].
(Camcorder) (Only when the Tape
Recording Mode)
≥The icon appears.
47
LSQT0862
Edit mode
≥The size of still pictures recorded on a card from
Using the DV cable for Recording
(Digital Dubbing)
the external input becomes [640]. (This is not
maga-pixel still-picture recording.)
≥When recording still pictures on a card, you
cannot record sound.
By connecting other digital video equipment with
DV terminal and the Camcorder by using the DV
cable PV-DDC9/PV-DDC9-K (optional) 1,
high-image-quality dubbing can be done in digital
format.
≥Set to Tape Playback Mode. (Player/
recorder)
ª Analog/digital conversion
When setting [ADVANCE] >> [DV OUT] >> [ON],
you can output video input from other equipment
in analog form to other digital video equipment
connected through the DV terminal in digital form.
1 Insert the DV cable PV-DDC9/PV-DDC9-K
(optional) securely into the DV terminal as
far as it will go.
1 Connect the Camcorder and digital video
equipment with the DV cable.
1) Other equipment (Video equipment, etc.)
2) Camcorder
DV
3) Other digital video equipment
1
1)
DV
2 Set [ADVANCE] >> [REC STDBY] >> [YES].
(Recorder)
2)
3)
≥You do not have to follow this step when the
remote control is used in the digital dubbing.
3 Start playback. (Player)
DV
4 Start recording. (Recorder)
≥A Analog signal
Other equipment (Video equipment, etc.) #
Camcorder
Move the joystick up to select [¥/;] icon.
≥B Digital signal
Camcorder # Other digital video equipment
≥When a pause or cue/review playback is
activated on other equipment during analog/
digital conversion, the image may be disturbed
or no image may be presented.
≥Normally, set [DV OUT] >> [OFF]. If set to [ON],
the image may be disturbed.
Or, while pressing the [¥REC] button on the
remote control, press the [1] button.
¥REC A.DUB
V
W
FF/
/REW PLAY
W
VOL
STILL ADV PAUSE STILL ADV
STOP
5 Move the joystick up to select the [¥/;]
icon again or press the [;] button on the
remote control to stop recording.
(Recorder)
6 Stop playback. (Player)
48
LSQT0862
Edit mode
ª To cancel the standby for recording
Audio dubbing
When the Camcorder is in standby for recording,
You can add music or narration to the recorded
cassette.
move the joystick down and select the [∫] icon.
≥Set to Tape Playback Mode. (If you perform
external input, set [BASIC] >> [AV JACK] >>
[IN/OUT], and connect an input device.)
Audio dubbing using the microphone terminal
1 Insert a Magic Wire Remote Control with
Narration Mic or an external microphone
securely into the [REMOTE/MIC] terminal as
far as it will go.
≥Do not plug or unplug the DV cable during
dubbing, or the dubbing may not be completed
properly.
≥If a picture (bilingual video, etc.) containing main
sound and sub sound has been dubbed, select
the desired sound using [SETUP] >>
[AUDIO OUT] on playback.
≥Even if you use a device equipped with DV
terminals such as IEEE1394, you may not be
able to perform digital dubbing in some cases.
For more information, see the instructions for
equipment connected.
REMOTE/MIC
≥Regardless of the menu settings on the
recorder, digital dubbing is carried out in the
same mode as the [AUDIO REC] mode of the
playback tape.
≥The images on the recorder monitor may be
disturbed, but it does not affect the recorded
images.
≥If a picture containing a copyright protection
signal (copy guard) is recorded by the
Camcorder, the picture is distorted by
mosaic-like patterns at playback.
2 Set [ADVANCE] >> [A. DUB INPUT] >>
[MIC].
Audio dubbing (external input) using other
equipment (audio equipment, etc.)
1 Insert the AV cable (supplied) securely into
the AV terminal as far as it will go.
≥Disconnect the USB cable since input signals
from the external input terminal cannot be
recorded while it is connected with the USB
cable.
AV/
≥When wide images are input, the display such
as the menu screen or the operation icon is
expanded horizontally.
≥While pictures are input from the DV terminal,
the operation icon blinks on instead of
appearing from the side of the screen when you
press the center of the joy stick.
2 Set [ADVANCE] >> [A. DUB INPUT] >>
[AV IN].
3 Find a scene that you want to add sound to,
and press the [;] button on the remote
control.
CAUTION:
V
W
FF/
/REW PLAY
;
W
Unauthorized exchanging and/or copying of
copyrighted recordings may be copyright
infringement.
VOL
STILL ADV PAUSE STILL ADV
STOP
4 Press the [A.DUB] button on the remote
control to make audio dubbing ready.
ZOOM
A.DUB ;
T
¥REC A.DUB
V
W
FF/
/REW PLAY
W
VOL
STILL ADV PAUSE STILL ADV
49
LSQT0862
Edit mode
5 Press the [;] button on the remote control
to start audio dubbing.
V
W
FF/
/REW PLAY
A.DUB ¥
W
VOL
STILL ADV PAUSE STILL ADV
STOP
≥When the Magic Wire Remote Control with
Narration Mic is used, start recording with the
[TALK] button pressed.
≥Talk into the microphone. Or start play on the
playing device.
6 Press the [;] button on the remote control
to stop audio dubbing.
V
W
FF/
/REW PLAY
W
VOL
STILL ADV PAUSE STILL ADV
STOP
≥If a tape has a non-recorded portion when the
tape is dubbed, images and sounds may be
disturbed when this portion of the tape is played
back.
ª Before recording with audio dubbing
≥Set to Tape Recording Mode.
≥When you want to preserve the original sound
taken during recording, set [SETUP] >>
[AUDIO REC] >> [12bit] to take pictures. (When
set [16bit], the sounds taken during recording
are erased after recording with audio dubbing.)
≥Set [BASIC] >> [REC SPEED] >> [SP] to take
pictures.
ª To play back the sound recorded with
audio dubbing
You can switch between the sound recorded with
audio dubbing and the original sound.
Set [SETUP] >> [12bit AUDIO] >> [ST2] or [MIX].
[ST1]: It only plays back the original sound.
[ST2]: It only plays back the sound added by
audio dubbing.
[MIX]: It simultaneously plays back the original
sound and the sound added with audio
dubbing.
ª To dub audio while listening to a
pre-recorded sound
≥When pausing the audio dubbing, set the
[12bit AUDIO] on the [SETUP] Sub-Menu to
[ST2] and you can check the pre-recorded
sound. When the line input is used, you can dub
audio while listening to the pre-recorded sound
from the speaker.
50
LSQT0862
Edit mode
3 Move the joystick left and right to select a
desired picture, and then press it.
Printing pictures by directly
connecting to the printer (PictBridge)
To print pictures by directly connecting the
Camcorder to the printer, use a printer compatible
with PictBridge. (Read the operating instructions
for the printer.)
≥Insert a card and set to Picture Playback
Mode.
1 Connect the Camcorder and the printer with
the supplied USB cable.
4 Select the desired number of prints.
≥You can set up to 9 prints.
5 Select the setting for date printing.
≥If the printer is not capable of date printing,
this setting will be unavailable.
6 Select the paper size.
[STANDARD]: Size specific to the printer
[4k5 INCH]
[5k7 INCH]
[4k6 INCH]
[A4]
≥You cannot set paper sizes not supported on
the printer.
7 Set [PRINT] >> [YES] to start printing.
1
ª When you stop printing halfway
Move the joystick down.
1 USB cable
PictBridge
≥Avoid the following operations during printing.
These operations disable proper printing.
≥Disconnecting the USB cable
≥Removing the card
≥Switching the mode dial
≥Turning off the power
≥Check the settings for the paper size, quality of
print, etc. on the printer.
≥You cannot print pictures that cannot be played
on the Camcorder.
≥The [PictBridge] indication appears on the
screen of the Camcorder.
(When the printer is being recognized, the
[PictBridge] indication blinks.)
≥When no card is inserted in the Camcorder, the
[PictBridge] indication does not appear. (You
cannot print any pictures.)
≥When the Camcorder and the printer are not
connected properly, the [PictBridge] indication
keeps blinking. (It will blink for just over
1 minute.) Connect the cable or check the
printer.
≥When the Camcorder and the printer are
connected in the Tape Recording/Playback
Mode, the [
WEB] or the [ WEB] Indication
may appear on the LCD monitor. However,
pictures cannot be printed.
≥We recommend using the AC adaptor as the
power supply.
≥When images are displayed in multi-screen,
they cannot be printed.
2 Select [SINGLE PRINT] or [DPOF PRINT].
≥If there is no file with a DPOF setting, you
cannot select [DPOF PRINT].
≥When you select [DPOF PRINT] for printing
set the number of prints in DPOF setting.
≥When [DPOF PRINT] is selected, print after
you determine the paper size.
51
LSQT0862
With a PC
Using USB Driver
With a PC
Using the Camcorder with a PC
ª Operating environment
≥Despite having the operating environment
indicated, it may not be possible to use the
program with some types of personal
computers.
≥A CD-ROM drive is required to install this
program.
≥When you connect to an USB 2.0 interface
board, use a certified board with the USB 2.0
(HI-SPEED USB) logo.
An image stored on the DV Cassette can be
transferred to your personal computer.
ª Software Installation
1 Turn on Computer and start up Windows.
2 Insert supplied CD-ROM into the CD-ROM
drive.
≥[Setup Menu] appears.
For Windows
OS:
IBM PC/AT compatible personal computer with
pre-installed;
Microsoft Windows 98 Second Edition
CPU:
Intel Pentium II/Celeron 300 MHz or higher
(including compatible CPU)
RAM:
32 MB or more (64 MB or more recommended)
Interface:
3 Select the software to be installed from
[Setup Menu].
≥USB Driver -52-:
The USB driver to be installed is the
dedicated Mass Storage Driver for Windows
98SE.
USB 1.1 or more
≥For Windows Me/2000/XP users, the USB
equipment operates with the driver installed as
standard in OS.
≥Video Stream Driver -54-:
If the Camcorder is connected to your
personal computer, you can send video from
the Camcorder to the other parties via a
network or by the Internet. It is also needed
connection.
For Macintosh
OS:
Mac OS X v 10.1–X v 10.3
CPU:
iMac, iBook or Power Book G4, Power Mac G4 or
Power Mac G5
≥DirectX
RAM:
64 MB or more
≥The USB equipment operates with the driver
installed as standard in OS.
To activate MotionDV STUDIO, Microsoft
DirectX 9.0b or later should be installed. (If
you install Video Stream Driver, DirectX 9.0b
is automatically installed.)
≥MotionDV STUDIO -56-:
ª Installing the USB Driver
When your OS is Windows 98SE, please install
USB Driver first before connecting the Camcorder
to your personal computer with the USB
connection Cable.
1 Turn on the personal computer and start up
Windows.
2 Insert the supplied CD-ROM into the
personal computer’s CD-ROM drive.
≥Quit all applications.
≥[Setup Menu] appears.
3 Click the [USB Driver].
≥The set up program starts running.
4 Click [Restart] if the [InstallShield] dialog
appears.
≥Do not remove the CD-ROM.
5 Finish installation by following the
on-screen instructions.
Using the MotionDV STUDIO software allows
you to capture video recorded on a tape or
images viewed through the lens of a
Camcorder. Connecting the Camcorder with
the DV cable also allows you to output
images edited on the personal computer to
the tape in the Camcorder.
4 Follow the instructions on the computer
screen until the installation is complete.
≥Setup window will disappear when the
installation is complete.
Note:
If a window does not appear automatically, click
the “Start” Button on your desktop and then click
“Run”. When the “Run” Box is open, type in
“D:\InstMenu.exe” and click “OK”. (“D” is used
when the CD-ROM drive is drive D.)
52
LSQT0862
With a PC
≥Click [Next] and proceed with installation.
≥After completing the installation, Click
[Finish].
6 After the USB Driver is installed, please
restart your computer.
5 Double-click a file you want to view.
6 Camcorder power is turned on.
≥You can view images stored on the Memory
Card and also save them to your hard disk.
≥Do not change file or folder names on the
personal computer. The images on the
Memory Card may not be viewable on the
Camcorder.
≥Appropriate driver to recognize Camcorder is
automatically installed by Windows Plug and
Play when connected for the first time.
≥After the USB Driver is installed and USB
connection cable is connected to the
Camcorder, open [My Computer] or
≥Reboot the computer to finish installing USB
driver.
≥Installation continues after the computer
reboots if you selected additional software.
≥A message indicating a conflict between
versions may be displayed during the
installation. This will not cause a problem.
Simply click [Yes] to proceed with the
installation.
[Windows Explorer] to check that the drive is
displayed as a removable disk drive (only when
card is inserted into the Camcorder). It enables
you to operate it in the same way as a floppy
disk drive, and you can use the same drag and
drop or copy methods.
Connecting Computer and
Camcorder
When your OS is Windows 98SE, install USB
Driver before connecting.
Never connect the USB cable until the USB
Driver is installed.
Before making these connections, turn off all
devices, which are to be connected.
≥It is recommended that you use the AC Adaptor
as the power supply of the Camcorder.
Using as a Web camera
If the Camcorder is connected to your personal
computer, you can send video and sound from
the Camcorder to other parties via the network.
Note:
≥Do not connect the USB cable until the Video
Stream Driver is installed.
This feature can be used only if both parties
are using the same operating system. Please
see chart below:
ª Using Built-in SD Drive
By connecting the Camcorder and personal
computer with the USB cable, you can transfer
still images saved on a Memory Card directly to
your personal computer.
1 Insert the Memory Card into the Camcorder.
2 Set the Camcorder to PC Mode.
[Send]
[Receive]
[Software]
Windows XP <OK> Windows XP Windows
Messenger
Windows XP <NG> Windows
PC
98SE/Me/
2000
Windows
98SE/Me/
2000
<OK> Windows
98SE/Me/
MSN
Messenger
3 Connect the Camcorder to your personal
computer with the USB cable.
2000
ª Operating environment
OS:
IBM PC/AT compatible personal computer with
preinstalled
Microsoft Windows XP Home Edition/
Professional SP1 or later
Microsoft Windows 2000 Professional SP4 or
later
Microsoft Windows Me (Millennium Edition)
Microsoft Windows 98 Second Edition
CPU:
Intel Pentium III 450 MHz or higher
Celeron 400 MHz or higher (including compatible
CPU)
4 Open [My Computer] and click
[Removable Disk] (For Windows 98SE/Me/
2000 users).
Click [Open folder to view files using
Windows Explorer] and then [OK] (For
Windows XP users).
53
LSQT0862
With a PC
RAM:
2 Click [Video Stream Driver].
≥The set up program starts running.
3 Depending on your system environment,
installation of “DirectX 9.0b” may be
required. Click [Yes] and continue with
installation.
128 MB or more (256 MB or more recommended)
Free hard disk space:
250 MB or more
Communication Speed:
56 kbps or faster is recommended
Interface:
≥After “DirectX 9.0b” is installed, the computer
USB 1.1 or more
will restart.
Graphic display:
High Color (16 bit) or more
Desktop resolution of 800k600 pixels or more
Other requirements (to send/receive audio):
Sound card
Speaker or headphones
Necessary software:
≥Do not remove the CD-ROM.
≥Installation may take a little while.
4 Finish installation by following the
on-screen instructions.
≥Click [Next] and proceed with installation.
≥After completing the installation, Click
[Finish].
Windows Messenger 5.0 or later (Windows XP)
MSN Messenger (Windows 98SE/Me/2000)
DirectX 9.0b or later (Windows XP)
To use the Camcorder as a Web camera, the
following conditions must be met.
≥Windows XP SP1 or later is needed.
≥To upgrade Windows XP to SP1 or later, click
[Start] >> [All Programs] >> [Windows Update].
(Requires Internet connection.)
≥To upgrade Windows 2000 Professional to SP4,
click [Start] >> [All Programs] >>
[Windows Update]. (Requires Internet
connection.)
5 Click [OK].
ª Connecting the Camcorder to
personal computer (For Use as a Web
Camera)
1 Install the supplied Video Stream Driver on
the provided CD-ROM.
2 Set the Mode Dial to Tape Recording Mode.
3 Set [ADVANCE] >> [USB FUNCTION] >>
[WEB CAM].
≥You have direct dial-up connection capability to
the Internet (minimum requirement). Also, you
and the other person(s) are on the same
Network (LAN).
≥Install Windows Messenger (Windows XP). If
you have a version older than 5.0, download the
latest version (5.0 or later) from the Microsoft
Home Page.
≥To send pictures recorded on a tape to
another personal computer using Windows
Messenger, set [BASIC] >>
[USB FUNCTION] >> [WEB CAM] on Tape
Playback Mode before connecting the
Camcorder to your personal computer.
When you use the Camcorder as a Web
camera in the Tape Playback Mode, the
indication of the operation icon is different
from the one in usual operation.
(For download and installation instructions,
please refer to Help on the Home Page.)
≥If the installed version is not the latest, update it
by performing the Windows update.
≥If you are connected to the Internet through a
firewall or a router, proper communication will
not be possible.
1
2
ª Installing Video Stream Driver
DirectX 9.0b must be installed in your PC if it is
not already installed.
≥When DirectX 9.0b is installed, applications
supported by previous versions of DirectX may
not run. In this case, consult the manufacturers
of the disabled applications.
1 Insert the supplied CD-ROM into the
personal computer’s CD-ROM drive.
≥Quit all applications.
1 In usual operation
2 In the WEB CAMERA mode (Tape Playback
Mode)
≥Even if you move the joystick up/down/right/left
(
, ∫, 5, 6), the selected direction on
the operation icon is not lit in yellow.
≥The operation icon blinks on instead of
appearing from the side of the screen when you
press the center of the joy stick.
4 Connect the Camcorder to a personal
computer with the USB connection cable.
≥[Setup Menu] appears.
54
LSQT0862
With a PC
≥When you use Windows XP, the other parties
≥When the Camcorder and personal
computer (with Windows 2000) are
via the network have to use Windows
connected via USB cable, a message, such
as the one below, is displayed. However,
testing by the manufacturer has confirmed
functionality of this Camcorder with
Windows 2000. Click [Yes] and proceed.
Messenger on Windows XP. When you use an
operating system other than Windows XP, the
other parties via the network have to use MSN
Messenger on an OS other than Windows XP.
≥If the Camcorder is used as a Web Camera, the
quality of the video to be exchanged will depend
on the Internet connection status.
≥In the WEB CAMERA mode, video cannot be
recorded onto a tape or a card.
≥You cannot output the video input from the DV
terminal to the display of the PC.
≥In the WEB CAMERA mode, the audio may be
interrupted in the middle of communication
depending on the communication environment
or the performance of the personal computer.
≥For Windows 98SE/Me users, “USB Audio
Device” is required. Click [Next] and
proceed.
≥If you use Windows 98SE, the OS installation
CD may be required.
ª Setting up Windows Messenger
When starting Windows Messenger for the first
time, its setup screen is displayed. (However, the
screen is not displayed if the Windows
Messenger setup has already been done.) For
more details, please read the corresponding Help
file.
For Windows 98SE/Me Users
The following messages may be displayed during
the installation depending on the environment of
the personal computer. Install the USB Driver as
instructed below.
1) The message “The file ‘kstvtune.ax’ on
[Unknown] cannot be found...” is
displayed.
1 Click [Click here to sign in].
2 Select [.NET Messaging Service] and click
[OK].
≥Enter “C:\Windows\system” for
Windows 98SE.
≥Enter “C:\Windows\options\CABS” for
Windows Me.
3 After the .NET Passport Wizard is displayed,
click [Next].
≥If the “kstvtune.ax” file is missing in one of
the 2 above-mentioned folders, insert the
OS CD-ROM and assign the path.
2) The message “The file ‘ksclockf.ax’ on
[Unknown] cannot be found...” is
displayed.
≥Enter “C:\Windows\system”.
≥Please refer to the instruction manual of your
personal computer for how to configure the
audio and the microphone.
≥To communicate with persons using Windows
in other languages, setting up using
alphabets or numbers is recommended.
4 According to the procedures displayed on
the screen, continue the setup.
≥If the “ksclockf.ax” file is missing in the
above mentioned folder, insert the OS
CD-ROM and assign the path.
≥You may click [Browse] to look for and assign
the path.
5 Start Windows Messenger (for Windows XP
users) or MSN Messenger (for Windows
98SE/Me/2000 users).
5 After the setup is completed, sign in and
start Windows Messenger.
≥Windows Messenger is activated.
≥Click [Start] >> [Programs] >>
[Windows Messenger] or [MSN Messenger].
55
LSQT0862
With a PC
≥For other information about MSN Messenger,
please refer to Help.
≥When access is finished, close MSN
Messenger, then turn off the Camcorder.
Finally, disconnect the USB cable.
Using MotionDV STUDIO
6 Click on [Audio Tuning Wizard...] in the
[Tools] menu to confirm that equipment is
connected correctly.
7 Select [USB Video Device] in the [Camera]
menu.
8 Select [DVC] in the [Microphone] menu.
≥Please refer to the HELP file of Windows
Messenger to understand its operation.
≥During set up, if [Primary video capture
device] selection screen is displayed,
[Panasonic DVC Web Camera] is selected.
When the OS is Windows XP/2000/Me, the
Camcorder can be connected to the personal
computer with the DV cable.
When the OS is Windows XP/2000, the
Camcorder can be connected to the personal
computer with the USB cable, however, Video
Stream Driver must be installed.
≥Do not connect the USB cable until the Video
Stream Driver is installed.
ª Operating environment
OS:
IBM PC/AT compatible personal computer with
ª Setting up MSN Messenger
When starting MSN Messenger for the first time,
its setup screen is displayed. (However, the
screen is not displayed if MSN Messenger setup
has already been done.) For more details, please
read the corresponding Help file.
pre-installed
Microsoft Windows XP Home Edition/
Professional SP1 or later
Microsoft Windows 2000 Professional SP4 or
later
1 Click [Sign In].
Microsoft Windows Me (Millennium Edition)
(Only in DV connection)
CPU:
Intel Pentium III 700 MHz or higher/AMD Athlon
1 GHz or higher (including compatible CPU)
Graphic display:
High Color (16 bit) or more
(32 bit or more recommended)
Desktop resolution of 1024k768 pixels or more
(Supporting the overlay of DirectDraw)
4 MB or more video memory
Sound:
PCM sound source (Compatible Direct Sound)
RAM:
256 MB or more
2 Type in your Sign-in name and password.
≥If you do not have your Sign-in name and
password, click [Get one here]
3 Please carefully read the displayed
contents and then proceed.
4 After the setup is completed, sign in and
start MSN Messenger.
(Adding more memory enables you to operate the
personal computer more comfortably.)
Hard disk:
Ultra DMA – 33 or more
Free hard disk space:
640 MB
(When you capture video, 1 GB is needed for
data of approx. 4 minutes.)
Interface:
DV (IEEE1394) terminal (IEEE1394.a)
USB 2.0 (Hi-Speed compliant)
DirectX 9.0b or later
Windows Media Player 6.4 or later
Other requirements:
Mouse
5 Click on [Audio Tuning Wizard...] in the
[Tools] menu to confirm that equipment is
connected correctly.
6 Select the microphone attached to the PC in
the [Microphone] menu.
7 Click [Web Camera Settings...] in the [Tools]
menu.
8 Confirm that the [Panasonic DVC Web
Camera Device] is selected.
56
LSQT0862
With a PC
ª Installing Video Stream Driver
ª Installation of MotionDV STUDIO
1 Insert the supplied CD-ROM into the
personal computer’s CD-ROM drive.
≥Quit all applications.
≥[Setup Menu] appears.
2 Click the [MotionDV STUDIO].
Install this when your OS is Windows XP SP1 or
later, or Windows 2000 SP4 or later. (When your
OS is Window XP SP2 or later, installing video
stream driver is not needed.) Video Stream Driver
must be installed when you connect the
Camcorder to the PC with the USB cable and use
MotionDV STUDIO.
DirectX 9.0b is installed in your PC if it is not
installed beforehand.
≥When DirectX 9.0b is installed, applications
supported by previous versions of DirectX may
not run. In this case, consult the manufacturers
of the applications disabled.
1 Insert the supplied CD-ROM into the
personal computer’s CD-ROM drive.
≥Quit all applications.
3 Click [Next].
≥[Setup Menu] appears.
2 Click [Video Stream Driver].
≥The set up program starts running.
3 For Windows XP users:
Depending on your system environment,
installation of “DirectX 9.0b” may be
required. Click [Yes] and continue with
installation.
≥After “DirectX 9.0b” is installed, the computer
will restart.
≥After reading the displayed contents, please
carry out the installation according to
instructions.
≥Do not remove the CD-ROM.
4 Select the Video system.
≥Installation may take a little while.
4 Finish installation by following the
on-screen instructions.
≥Click [Next] and proceed with installation.
≥After completing the installation, Click
[Finish].
5 Click [OK].
5 After the completion of setup, click on
[Finish].
≥Sample data is installed concurrently with the
MotionDV STUDIO software.
6 Click [Finish].
57
LSQT0862
With a PC
If a description other than [Microsoft] is
ª To start MotionDV STUDIO
displayed
If you wish to capture data from a tape, set the
Camcorder to Tape Playback Mode and insert the
tape. If you wish to capture images from the lens
of the Camcorder, set the Camcorder to the Tape
Recording Mode and remove the tape and the
card.
≥Update the driver with the following procedure.
1 Click [Update Driver...].
With USB connection cable (supplied)
OS:
Windows XP SP1 or later
Windows 2000 SP4 or later
≥The personal computer should be compatible
with USB 2.0 Hi-Speed.
2 Check [Install from a list or specific location
(Advanced)] and then click [Next].
Confirmation before connection
(for Windows XP/2000)
When you connect the personal computer and the
Camcorder with the USB connection cable and
then use MotionDV STUDIO on Windows XP
(SP1 or later) or Windows 2000 (SP4 or later),
check the driver of the USB host controller.
≥It is required to use the driver for which
[Microsoft] is displayed on [Driver Provider] in
[Driver] tab.
1 Select [Start] >> [Settings] >>
[Control Panel] to start [System].
≥[System Properties] is displayed.
2 Click [Hardware] tab and then click
[Device Manager] then
≥When your OS is Windows 2000, click [Next]
after [Update Device Driver Wizard] appears.
3 (For Windows XP Users)
Check [Don’t search. I will choose the driver
to install] and then click [Next].
[Universal Serial Bus Controller].
3 Right-click [Enhanced Host Controller] and
then select [Properties].
(For Windows 2000 Users)
Check [Display a list of the known drivers
for this device so that I can choose a
specific driver] and then click [Next].
4 Click [Standard Universal PCI to USB Host
Controller] and then click [Next].
≥The indication [Enhanced Host Controller] is
changed as [EHCI] depending on the host
controller you use.
4 Click [Driver] tab to check the description
on [Driver Provider].
5 Click [Finish].
≥The update of the driver is completed.
Connect the Camcorder.
≥If [Microsoft] is displayed on [Driver Provider],
the confirmation procedure is completed.
58
LSQT0862
With a PC
≥You can record the video edited by the PC onto
Connecting the Camcorder to a personal
computer
the Tape in the Camcorder.
1 Set the Mode Dial to Tape Recording Mode
≥When 2 or more USB devices are connected to
a personal computer, or when devices are
connected through USB hubs or by using
extension cables, proper operation is not
guaranteed.
or Tape Playback Mode.
2 Set [BASIC] or [ADVANCE] >>
[USB FUNCTION] >> [MOTION DV].
≥When connected to the keyboard USB terminal,
normal function may not be possible.
To disconnect USB cable safely
If USB cable is disconnected while computer is
on, error dialog box may appear. In such a case
click [OK] and close the dialog box. By following
the steps below you can disconnect the cable
safely.
≥It enters MotionDV STUDIO Mode.
3 Connect the Camcorder to the personal
computer with USB connection cable.
1 Double click the
icon in task tray.
≥Hardware disconnect dialog box appears.
2 Select [USB Mass Storage Device] and click
[Stop].
3 Verify [Matshita DVC USB Device] is
selected and click [OK].
4 Select [Start] >> [All Programs (Programs)]
>> [Panasonic] >>
[MotionDV STUDIO 5.3E LE for DV] >>
[MotionDV STUDIO LE for DV].
≥Using the MotionDV STUDIO for Windows, a
variety of visual effects can be added and titles
can be created.
≥You cannot record a video edited by the PC
onto the Tape in the Camcorder.
With DV cable (optional)
≥You can safely disconnect the cable.
Note on the driver name displayed
OS:
The driver name displayed will differ depending
on your OS, operating environment and the mode
of the Camcorder.
Windows Me/2000/XP
1 Set the Mode Dial to Tape Recording Mode
or Tape Playback Mode.
2 Connect the Camcorder to the personal
computer with DV connection cable.
≥Some Operating Systems, such as Windows
98SE, may not show the icon indicating that you
may safely disconnect in task tray. (OS may be
set not to show.) Make sure Camcorder’s Card
Access Lamp is off and disconnect the cable.
Also, with Windows Me, the icon will not be
displayed when in Tape Recording Mode or
Tape Playback Mode.
DV
CAUTION:
If you disconnect the USB cable while the
Card Access Lamp is on, it may damage the
Card data.
3 Start MotionDV STUDIO 5.3E LE.
59
LSQT0862
With a PC
If the above operation is not performed correctly,
≥These instructions do not cover the basic
operations of the personal computer or define
any terms. For this information, refer to the
Operating Instructions which accompany your
personal computer.
≥Do not disconnect USB connection cable while
the operation light of Camcorder is on. It may
freeze the software or destroy the data in
transfer.
when data is copied from the personal computer
to an SD Memory Card, the copied data may be
damaged.
When the following operations are performed, the
same results will occur as when the USB cable is
incorrectly removed (above). Therefore, it is
imperative that the above operation is completed
before proceeding.
≥When SD Memory Card is removed.
≥When Camcorder power is turned OFF.
≥We recommend using the AC adaptor as the
power source for the Camcorder when
connecting to the personal computer. Data may
be lost If the battery power is lost while
transferring data.
≥If the Camcorder is used as a Web Camera
while virus checking software is running, the
Camcorder’s operation may stop midway
through. In this case, exit the Windows
Messenger, reconnect the Camcorder and
restart the Windows Messenger.
≥When Mode Dial is turned to change modes.
≥Do not delete the folders in Memory Card such
as picture folder. Memory card may not be
recognized if folders are deleted.
PC
≥When the Camcorder is switched to the PC
Mode while it is connected to the personal
computer, the operation mode of the Camcorder
cannot be switched. In this case, disconnect the
USB connection cable. Switch the operation
mode of the Camcorder and reconnect the
cable.
≥If the Camcorder is connected in the PC Mode,
the [Removable Disk] icon representing the
Memory Card drive is displayed in
If you no longer need software or
driver (Uninstall)
The screens may vary with the type of OS.
1 Select [Start] (>> [Settings]) >>
[Control Panel], select the software or the
driver from [Add/Remove Programs] to
uninstall.
≥Uninstalling steps may vary depending on the
OS. Please refer to the user manual of your OS.
[My Computer].
≥When the Tape Recording Mode of the
Camcorder is switched to the PC Mode, a
warning message may be displayed. You may
simply ignore it.
≥When you are using Windows XP or Windows
2000, you may install or uninstall this software
after logging ON by setting the user name to
Administrator or to a user name having
equivalent authority.
Notes
®
®
®
≥Microsoft , Windows , Windows Messenger
®
and DirectX are either registered trademarks
or trademarks of the Microsoft Corporation in
the United States and/or other countries.
®
®
®
≥Intel , Pentium and Celeron are the
registered trademarks or trademarks of the Intel
Corporation.
≥If you use Windows 98SE, the message, “File is
not found” may be displayed when the
Camcorder is connected for the first time. Enter
the following paths to complete the connection:
If the message “MTDV98M3.pdr is not found” is
displayed, enter
“C:\WINDOWS\system\IOSUBSYS”. If the
message “MTDV98M3.sys is not found” is
displayed, enter
≥
All other names, company names, product names,
etc. in these instructions are the trademarks or
registered trademarks of their respective corporations.
≥The names of the products you are using may
differ from the names given in the text.
Depending on the operating environment and
other factors, the contents of the screens used
in these instructions may not necessarily match
what you will see on your screen.
“C:\WINDOWS\system32\DRIVERS”.
(The paths will differ depending on the
environment of your personal computer.)
≥
Although the screens in these Operating
Instructions are shown in English for the sake of
example, other languages are supported as
well.
60
LSQT0862
With a PC
≥If you install the USB Driver or video stream
ª About the folder structure when using
the Memory Card in a personal
computer
≥When a Card with data recorded on it is inserted
into a personal computer, folders will be
displayed as shown in the following figure.
driver while the USB Connecting cable is being
connected, or if you do not follow these
Operating Instructions, the Camcorder will not
be recognized correctly. In this case, delete the
USB Driver from [Device Manager] as described
below, uninstall the USB Driver, and re-install it.
1 Set the Camcorder to Tape Recording Mode
or Tape Playback Mode, connect it to the
personal computer, and delete
256
[USB Video Device] (or [Panasonic DVC DV
Stream Device]) from [Device Manager].
2 Set the Camcorder to PC Mode and delete
[Panasonic DVC USB Storage] (Windows
98SE).
DCIM
100CDPFP
MISC
[100CDPFP]: The images (IMGA0001.JPG,
etc.) in this folder are recorded in
the JPEG format.
ª About the SD Memory Card
SD Memory Card
The SD Memory is an external Memory Card that
is available in larger capacities. It has a write
protect switch to prevent data writing and card
formatting, as well as a copyright protection
function.
[MISC]:
Files in which DPOF Data has
been set to the image are in this
folder.
≥[DCIM] etc. are necessary items in the folder
structure. They have nothing to do with actual
operation.
≥SD Logo is a trademark.
≥In Card Mode, the Camcorder automatically
saves file numbers (IMGA0001.JPG, etc.) along
with the images. The file numbers are recorded
with each image as consecutive numbers.
≥When using the software without indication
function, indication data, such as date, are not
displayed. Depending on the software in use,
the date and the time may not be displayed
correctly.
≥The memory capacity indicated on the SD Card
label corresponds to the total card capacity.
Some of this capacity is used to protect and
manage the copyright data, and not all capacity
is available as conventional memory for a
Camcorder, personal computer or others.
≥All other company and product names in the
operating instructions are trademarks or
registered trademarks of their respective
corporations.
Files recorded on a SD Memory Card
It may not be possible to play back the files on
this Camcorder recorded on and created by other
equipment or vice versa. For this reason, check
the compatibility of the equipment in advance.
ª About the compatibility of the card
files
Data files recorded on an “SD Memory Card” by
this Camcorder conform with DCF (Design rule
for Camera File system) established by JEITA
(Japan Electronics and Information Technology
Industries Association).
≥If you attempt to play back files recorded with
this Camcorder on other equipment or to play
back files recorded with other equipment on this
Camcorder, you may not be able to play them
back. Please check the compatibility with the
other equipment in advance.
61
LSQT0862
Menu
ª
[TAPE PLAYBACK MENU]
Menu
Menu list
Menu figures and illustrations are provided for
easy-to-understand explanations, and so they are
different from the actual menu indications.
ª
[TAPE RECORDING MENU]
1) [BASIC]
[DATE/TIME] -64-
[AV JACK] -49-
[USB FUNCTION] -54-
2) [ADVANCE]
[BLANK SEARCH] -29-
[REC SPEED] -27-
[REC STDBY] -48-
[AUDIO REC] -64-
[A. DUB INPUT] -49-
[REC DATA] -64-
[PICT. QUALITY] -31-
[DV OUT] -48-
[REPEAT PLAY] -41-
1) [BASIC]
[SCENE MODE] -37-
[REC SPEED] -27-
[BLANK SEARCH] -29-
[WIND CUT] -34-
[CLOCK SET] -23-
2) [ADVANCE]
[PICT. QUALITY] -31-
[FLASH] -35-
[RED EYE] -35-
[FLASH LEVEL] -35-
[EIS] -36-
[H.SHOE MIC] -64-
[WIDE] -36-
[CINEMA] -36-
[USB FUNCTION]-54-
[D.ZOOM] -31-
[ZOOM MIC] -32-
[DATE/TIME] -64-
[INITIAL SET] -65-
3) [SETUP]
[12bit AUDIO] -50-
[AUDIO OUT] -64-
[DISPLAY] -64-
[REMOTE] -25-
[LCD AI] -24-
[LCD SET] -23-
[EVF SET] -23-
[POWER SAVE] -28-
4) [LANGUAGE] -21-
3) [SETUP]
[FADE COLOR] -34-
[AUDIO REC] -64-
[REC LAMP] -64-
[DISPLAY] -64-
[REMOTE] -25-
[BEEP SOUND] -64-
[LCD AI] -24-
[LCD SET] -23-
[EVF SET] -23-
[DEMO MODE] -65-
[AV JACK] -64-
[POWER SAVE] -28-
4) [LANGUAGE] -21-
62
LSQT0862
Menu
ª
[CARD RECORDING MENU]
ª
[PICTURE PLAYBACK MENU]
2048
1) [BASIC]
[DATE/TIME] -64-
[PROTECT] -45-
1) [BASIC]
[SCENE MODE] -37-
[PICT. QUALITY] -31-
[PICTURE SIZE] -31-
[SELF TIMER] -36-
[CLOCK SET] -23-
2) [ADVANCE]
[DPOF SET] -45-
[CARD FORMAT] -45-
2) [ADVANCE]
[BURST MODE] -37-
[FLASH] -35-
[RED EYE] -35-
[FLASH LEVEL] -35-
3) [SETUP]
[DISPLAY] -64-
[REMOTE] -25-
[LCD SET] -23-
[EVF SET] -23-
[LCD AI] -24-
[EIS] -36-
[SHTR EFFECT] -31-
[DATE/TIME] -64-
[INITIAL SET] -65-
[POWER SAVE] -28-
4) [LANGUAGE] -21-
3) [SETUP]
[REC LAMP] -64-
[DISPLAY] -64-
[REMOTE] -25-
[BEEP SOUND] -64-
[LCD AI] -24-
[LCD SET] -23-
[EVF SET] -23-
[POWER SAVE] -28-
4) [LANGUAGE] -21-
63
LSQT0862
Menu
Menus related to taking pictures
Menus related to playback
ª [H.SHOE MIC]
ª [AV JACK]
Set to [LOWCUT] and this reduces low sound
noise and wind noise hitting the stereo zoom
microphone (VW-VMH3; optional) mounted on
the smart accessory shoe.
This switches among the output settings of the
AV/headphone terminal.
[IN/OUT]: Use this setting when inputting signals
from other equipment via an AV cable
or a S-Video cable.
[OUT/Ë]: Automatically switches between AV
and headphone output.
ª [DATE/TIME]
This switches between date and time indications.
≥The Camcorder automatically records the date
and time the picture was taken on the tape.
≥You can also show or change the date/time
indication by repeatedly pressing the [DATE/
TIME] button on the remote control.
[OUT]:
Use this setting when image or sound
is not output normally to the TV in
[OUT/Ë].
≥When using the headphone, set to [SETUP] or
[BASIC] >> [AV JACK] >> [OUT/Ë]. If set to
[OUT], you may hear noises on the right.
ª [AUDIO REC]
Switches the audio (PCM audio) recording
systems.
[12bit]: Records audio in “12 bit 32 kHz 4 tracks”.
(The original audio signals can be kept
after the other audio signals are dubbed.)
[16bit]: Records audio in “16 bit 48 kHz 2 tracks”.
Audio can be recorded in higher quality.
(If audio signals are dubbed, then the
original audio signals will be erased.)
ª [REC DATA]
Set to [ON] and the settings (shutter speed, iris/
gain values, and white balance settings (-38-),
etc.) used during the recordings are displayed
during playback.
≥When the [AUTO/MANUAL/FOCUS] switch is
set to [AUTO], the indication [AUTO] will
appear.
≥When there is no data, [---] appears on the
display.
≥If the Camcorder data of the Camcorder are
played back on other equipment, the settings
information is sometimes not displayed
normally.
ª [REC LAMP]
Set to [ON] and this turns the recording lamp on
during recording, which indicates that recording is
underway. Set to [OFF] and this does not turn on
the lamp even when recording is underway.
ª [DISPLAY]
ª [AUDIO OUT]
Set to [ON] and the display mode can be switched
to all functions. Set to [OFF] and it can be
switched to minimum display.
This switches the sound to be played back.
[STEREO]: Stereo sound (main sound and sub
sound)
[L]:
[R]:
Left channel sound (main sound)
Right channel sound (sub sound)
ª [BEEP SOUND]
Set to [ON] and confirmation/alarm beeps are
issued as follows.
1 Beep
≥When you start recording
≥When you turn on the power
2 Beeps
≥When you pause recording
2 Beeps for 4 times
≥When a cassette with its erasure prevention tab
set to [SAVE] is inserted, condensation occurs,
and at other times. Check the sentence
displayed on the screen.
64
LSQT0862
Menu
Other menus
ª [INITIAL SET]
When there is a menu that cannot be selected
depending on a combination of functions, set to
[YES] for changing the menu settings back to the
initial shipping condition.
(Language setting cannot be back to the initial
shipping condition.)
ª [DEMO MODE]
If you set to [DEMO MODE] >> [ON] without
inserting a cassette and a card, the Camcorder is
automatically set to the demonstration mode for
introducing its functions. If any button is pressed
or operated, the demonstration mode is canceled.
If no operations take place for approx.
10 minutes, the demonstration mode
automatically starts. To terminate the
demonstration mode, insert a cassette or a card,
or set to [DEMO MODE] >> [OFF]. For normal
use, set this function to [OFF].
65
LSQT0862
Others
LOWCUT
:
External microphone supporting
the smart accessory shoe (LOW
CUT) -13-
Others
Indications
5:
Sports mode (Scene mode) -37-
Portrait mode (Scene mode) -37-
Low light mode (Scene mode)
-37-
Spotlight mode (Scene mode)
-37-
Surf & snow mode (Scene mode)
-37-
Auto white balance -38-
Indoor mode (recording under
incandescent lamp) -38-
Outdoor mode -38-
Various functions and the Camcorder status are
shown on the screen.
Basic indications
r:
0h00m00s00f: Time code
:
:
Remaining battery power
:
:
3:30:45PM:
Date/Time indication
Recording indications
R 0:45:
(When it reaches less than 3 minutes, the
indication starts flashing.)
AWB
:
Remaining tape time
:
:
:
White balance adjustment mode
-38-
WEB CAMERA mode (recording)
-51-
SP:
Standard Play mode
(Recording speed mode) -27-
Long Play mode
Recording -28-
:
LP:
Playback indications
¥:
1:
;:
5:
6:
D/E:
;1/2;:
2k5:
:
¥:
Recording underway
Playback -41-
Pause -41-
; (Green):
; (Green flash):
Recording pause -28-
Standby mode
Fade out
Recording check -29-
wide mode -36-
Digital zoom -31-
Automatic mode -27-
Manual mode -37-
Manual focus -39-
Zoom magnification indication
-31-
Back light mode -33-
Shutter speed -40-
F number -40-
Gain value -40-
Soft skin mode -33-
Tele macro -34-
Fade (White) -34-
Fade (Black) -34-
MagicPix function -33-
0 Lux MagicPix function -33-
Video flash turned on -35-
VIdeo flash turned off -35-
Video flash (setting to [i]) -35-
Video flash (setting to [j]) -35-
Red eye reduction -35-
Zoom microphone -32-
Wind noise reduction -34-
When the microphone of the
Magic Wire Remote Control with
Narration Mic is used -26-
External microphone supporting
the smart accessory shoe -13-
Slow motion playback -42-
Frame-by-frame playback -42-
Variable-speed search -42-
Repeat playback -41-
WEB CAMERA mode (playback)
-51-
Audio dubbing -49-
Audio dubbing pause -49-
Prepared for audio dubbing
(microphone)
Prepared for audio dubbing (Line)
Blank search -29-
Audio dubbing input display -49-
Audio recording mode -64-
Volume adjustment -41-
; (Red):
:
CINEMA
:
WIDE :
:
:
AUTO
:
:
MNL
MF:
5k:
A.DUB ¥:
A.DUB ;:
:
:
1/500:
F2.4:
6dB:
:
MIC, AV IN:
12bit, 16bit:
:
:
:
:
:
Card
æ:
± (White):
¥ (Green):
:
Shutter chance mark -30-
Shutter chance mark -30-
RapidFire Consecutive Photoshot
recording -37-
Self-Timer recording -36-
MEGA Optical image stabilizer
-36-
:
0Lux
ß/ßA:
:
ßi/ßAi:
ßj/ßAj:
£:
:
MEGA
:
EIS
ZOOM
:
:
(White):
(Green):
:
Photoshot mode
:
While the card is being read
While photoshot recording is
activated
Using the card that cannot be
recognized
:
(Red):
66
LSQT0862
Others
(
):
Photoshot picture quality -31-
Remaining number of photoshot
pictures (When the remaining
number of photoshot pictures
reaches 0, the red indication
flashes.)
Slide show playback -43-
PictBridge mode -51-
Folder/File display
File number
Number of DPOF Setting -45-
Lock setting -45-
[640k480] Image size
[1280k960] Image size
[1600k1200] Image size
[2048k1512] Image size
Warning/alarm indications
0:
If any one of the following indications lights up or
Confirmatory indications
Y: A cassette with the accidental erasure
prevention slider placed in the [SAVE]
position is inserted.
No cassette is inserted.
[--]/0:
The built-in battery is low. -23-
you record yourself. Turn the LCD monitor
towards the viewfinder and check the
warning/alarm indication.
: No card is inserted.
REMOTE :
An incorrect remote control mode has been
selected. -25-
2END:
The tape came to the end during recording.
:: The video heads are dirty. -74-
:
PictBridge:
100-0001:
No.00:
1:
:
:
640
:
:
:
1280
1600
2048
≥For images not recorded with this Camcorder,
the size display is determined as follows
according to the number of horizontal pixels.
QXGA
UXGA
SXGA
:
:
:
2048 or more
1600 or more, less than 2048
1280 or more, less than 1600
1024 or more, less than 1280
800 or more, less than 1024
640 or more, less than 800
(The size is not displayed at
under 640 pixels.)
:
XGA
Textual indications
:
SVGA
3DEW DETECT/3EJECT TAPE:
cassette and wait for a while. It takes some
time until the cassette holder opens, but this
is not a malfunction. -73-
:
640
LOW BATTERY:
The battery is low. Recharge it. -16-
NO TAPE :
No tape is inserted. -18-
TAPE END:
The tape came to the end during recording.
CHECK REC TAB:
You are attempting to record pictures on a
tape with the accidental erasure prevention
slider placed in the [SAVE] position.
You are attempting audio dubbing or digital
erasure prevention slider placed in the
[SAVE] position.
CHECK REMOTE MODE:
An incorrect remote control mode has been
selected. This is only displayed at the first
operation of the remote control after
powering-on. -25-
WRONG TAPE FORMAT:
You are attempting to play back a tape
section that has been recorded with a
different TV system. This cassette is
incompatible.
UNPLAYABLE CARD:
You are attempting to play back data not
compatible with this Camcorder.
67
LSQT0862
Others
UNABLE TO A.DUB (LP RECORDED):
Audio dubbing cannot be performed
because the original recording was in LP
mode.
PRINTER ERROR:
Check the connected printer.
PC DOES NOT SUPPORT USB2.0:
The Camcorder is connected to a personal
computer that does not support USB 2.0.
CAN NOT USE USB:
UNABLE TO A.DUB:
You are attempting to perform audio
dubbing on a non-recorded tape.
COPY PROTECTED:
You are connecting the USB cable with the
DV cable connected.
Images cannot be recorded correctly
because the medium is protected by a copy
guard.
CHANGE TO MANUAL MODE:
You are attempting to select the item on the
[SCENE MODE] when the [AUTO/
MANUAL/FOCUS] switch is set to [AUTO].
CAN NOT OPERATE (MOTION DV MODE):
You are attempting to change [D.ZOOM]
setting during MotinDV Mode.
CARD ERROR:
This card is not compatible with this
Camcorder.
You are attempting to format a failed card.
It displays, when you attempt to insert an
incompatible card to Card Slot.
NO CARD:
REVERSE THE LCD MONITOR:
At the time of 0 Lux MagicPix mode, when
LCD monitor is not reversed, it displays.
When the LCD monitor is rotated by 180°
towards the lens, the brightness of the LCD
monitor cannot be adjusted.
No card is inserted.
CARD FULL:
Card does not have sufficient memory
remaining.
Select Picture Playback Mode and delete
unnecessary files.
NO DATA:
There are no recorded files on the card.
CHANGE ASPECT TO 4:3:
You are attempting to record pictures with
an aspect ratio of 16:9 by pressing the
[PHOTO SHOT] button.
FILE LOCKED:
You are attempting to erase protected files.
CARD LOCKED:
The write protection switch on the SD
Memory Card is set to [LOCK].
NEED HEAD CLEANING:
The video heads are dirty. -74-
PUSH THE RESET SWITCH:
An irregularity in the equipment has been
detected. Press the [RESET] button (-13-).
This may solve the problem.
CHANGE MODE TO USE USB:
The USB cable is connected to the
Camcorder in Card Recording Mode.
DISCONNECT USB CABLE:
You are attempting to turn the mode dial in
PC mode with the USB cable connected to
the Camcorder. You are attempting to
record pictures on a tape/card with the USB
cable connected to the Camcorder.
NO INK IN PRINTER:
There is no ink. Check the connected
printer.
NO PAPER IN PRINTER:
There is no paper. Check the connected
printer.
68
LSQT0862
Others
Functions cannot be used
simultaneously
≥Flash
≥While recording to a tape
≥During demo mode
≥When RapidFire
Consecutive Photoshot is
used
Some functions in the Camcorder are disabled or
cannot be selected due to its specifications. The
table below shows examples of functions
restricted by conditions.
≥When the MagicPix
function is used
Functions
Conditions which disable
the functions
≥Zoom
≥When the microphone of
the Magic Wire Remote
Control with Narration Mic
or an external microphone
is used
microphone
≥Wind noise
reduction
≥Progressive
≥When recording onto a
tape and a card
simultaneously
≥When digital zoom
(10k or higher) is used
≥When the shutter speed is
1/750 or faster in Tape
Recording Mode
≥When the gain value is
increased in Tape
Recording Mode
≥Scene mode
≥When setting the [AUTO/
MANUAL/FOCUS] switch
to [AUTO]
≥When the MagicPix
function is used
≥Change of
white balance
≥When digital zoom (10k
or higher) is used
≥When the MagicPix
function is used
≥When the shutter speed is
1/15 or slower in the Card
Recording mode
≥When a menu is
displayed
≥When brightness is
insufficient with the flash
[
] in Tape Recording
Mode
≥When the MagicPix
function is used
≥When the portrait mode of
the scene mode is used in
Tape Recording Mode
≥When the wide mode is
used
≥Adjusting the
shutter speed,
iris/gain
≥When the MagicPix
function is used
≥When the scene mode is
used
≥Variable-speed ≥During repeat playback
search
≥Digital zoom
≥Wide mode
≥Fade
≥When the Card Recording
mode is used
≥Deleting files
≥When the write protect
switch on the card is set
to [LOCK]
≥Backlight
compensation
≥When the iris/gain is set
≥When the MagicPix
function is used
≥When the file is protected
≥Formatting
≥When the write protect
switch on the card is set
to [LOCK]
≥Soft skin
≥Tele-macro
≥Recording
check
≥While recording to a tape
≥Audio dubbing
≥The section of a tape
recorded in LP mode
≥The blank section of a
tape
≥Sounds sent through the
DV terminal
≥MagicPix
≥While recording to a tape
≥When the Card Recording
mode is used
≥RapidFire
Consecutive
Photoshot
≥When [PICTURE SIZE] is
set to other than [640]
≥When the shutter speed is
1/15 or slower
69
LSQT0862
Others
6: The cassette cannot be removed.
Before requesting repair
(Problems and solutions)
the cassette cover? (-20-) Make sure that the
battery and the AC adaptor are properly
connected. (-16-)
Power/Body
1: The Camcorder power cannot be turned on.
• Is the battery fully charged? Use a fully
charged battery.
• Is the battery in use discharged? Charge the
battery and remove the cassette.
• The battery protection circuit may have
operated. Attach the battery to the AC adaptor
for 5 to 10 seconds. If the Camcorder still
cannot be used, the battery is faulty.
2: The Camcorder power is turned off
automatically.
• If you set [POWER SAVE] to [5 MINUTES] and
do not operate the Camcorder for about
5 continuous minutes, the power is
automatically turned off for tape protection and
power conservation. To resume recording, turn
the [OFF/ON] switch to [OFF]. Then turn it to
[ON] again. (-28-)
• Close the cassette cover completely, and fully
open it again. (-18-)
7: No operation other than cassette removal
can be performed.
• Has condensation occurred? Wait until the
condensation indication disappears. (-73-)
8: The remote control does not function.
• Has the button-type battery of the remote
control run out? Replace it with a new button-
type battery. (-25-)
• Is the setting on the remote control correct? If
the setting on the remote control is not in
agreement with the [REMOTE] setting on the
Camcorder, the remote control does not
operate. (-25-)
3: The Camcorder power does not stay on
long enough.
• Is the battery low? If the remaining battery
power indication is flashing or the message
“LOW BATTERY” is displayed, the battery has
run down. Charge the battery or attach a fully
charged battery. (-16-)
Recording
1: Recording does not start although power is
supplied to the Camcorder and the cassette
is correctly inserted.
• Has condensation occurred? When you carry
the Camcorder from a cold place into a warm
place, condensation may occur inside it. If so,
the power is turned off automatically, disabling
all operations except for taking cassettes out.
Wait until the condensation indication
disappears. (-73-)
4: Battery runs down quickly.
• Is the battery fully charged? Charge it with the
AC adaptor. (-16-)
• Are you using the battery in an extremely cold
place? The battery is affected by ambient
temperature. In cold places, the operating time
of the battery becomes shorter.
• Has the battery worn out? The battery has a
limited life. If the operating time is still too short
even after the battery is fully charged,
depending on the usage, the battery has worn
out and can no longer be used.
the cassette open? If it is open (set to [SAVE]),
recording cannot be performed. (-18-)
• Is the tape wound to the end? Insert a new
cassette.
• Is the recording mode set? When in the
playback mode, recording cannot be
performed. (-27-)
• Has condensation occurred? No operation
other than cassette removal can be performed
when condensation occurs. Wait until the
condensation indication disappears. (-73-)
• Is the cassette cover open? If the cover is
open, the Camcorder may not operate
normally. Close the cassette cover. (-18-)
2: The screen has changed suddenly.
• Has the demonstration started? In the Tape
Recording mode, if you set [DEMO MODE] >>
[ON] without inserting a cassette and a card,
the demonstration starts. For normal use, set
this function to [OFF]. (-65-)
5: The Camcorder cannot be operated though
powered up.
The Camcorder does not operate normally.
• Remove the cassette and then press the
[RESET] button. (-72-) If normal conditions are
not restored yet, turn off the power. Then,
about 1 minute later, turn on the power again.
(Conducting the above operation when the
access lamp is on may destroy the data on the
card.)
3: A cassette cannot be inserted.
• Has condensation occurred? Wait until the
condensation indication disappears.
4: Auto focus function does not work.
• Is manual focus mode selected? If auto focus
mode is selected, focus is automatically
adjusted.
70
LSQT0862
Others
• There are some recording subjects and
• Have you set [SETUP] >> [12bit AUDIO] >>
[MIX]? If you set [AUDIO REC] >> [12bit] and
dub audio to a recorded tape, you can hear the
sound on recording and the sound dubbed at a
later time. To hear the sounds separately, set
to [ST1] or [ST2]. (-50-)
• Have you set [SETUP] >> [AUDIO OUT] >>
[STEREO] and reproduced a picture containing
the main sound and sub sound? Set to [L] to
hear main sound, and set to [R] to hear the sub
sound. (-64-)
surroundings for which the auto focus does not
operate correctly. (-78-) If so, use the manual
focus mode to adjust the focus. (-39-)
• Is the MagicPix function set? When the
into the manual mode.
Indications
1: A sentence is displayed in red or yellow in
the screen center.
• Read the contents and respond to them.
(-67-)
3: Audio dubbing cannot be performed.
• Is the accidental erasure prevention slider on
the cassette open? If it is open (set to [SAVE]),
audio dubbing cannot be performed. (-18-)
• Are you attempting to edit a tape portion that
was recorded in LP mode? LP mode does not
allow audio dubbing. (-27-)
4: The original sound was erased when audio
dubbing was performed.
• If you perform audio dubbing on a recording
made in [16bit] mode, the original sound will be
erased. If you wish to preserve the original
sound, be sure to select [12bit] mode when
recording.
2: The time code becomes inaccurate.
0 The time code indication counter may not be
constant in the reversed slow-motion playback,
but this is not a malfunction.
3: The remaining tape time indication
disappears.
• The remaining tape time indication may
disappear temporarily during frame-by-frame
playback or other operation. If you continue
ordinary recording or playback, the indication is
restored.
4: The remaining tape time Indication does not
match the actual remaining tape time.
• If scenes of less than 15 seconds are
continuously recorded, the remaining tape time
cannot be correctly displayed.
• In some cases, the remaining tape time
indication may show remaining tape time that is
2 to 3 minutes shorter than the actual
remaining tape time.
5: A function indication such as mode
indication, remaining tape time indication,
or time cord indication is not shown.
• If you set [SETUP] >> [DISPLAY] >> [OFF],
indications other than the tape running
condition, warning, and date indications
disappear.
5: Sounds cannot be played back.
• Although a cassette with no audio dubbing is
[12bit AUDIO] >> [ST2]? To play back a
cassette with no audio dubbing, set
[12bit AUDIO] >> [ST1]. (-50-)
• Is the variable speed search function working?
Press the [VAR. SEARCH] button on the
remote control to cancel the variable speed
search function. (-42-)
6: Noise is heard from the right headphone.
• Have you set [BASIC] >> [AV JACK] >> [OUT]?
When you use the headphones, set to [OUT/
Ë].
Playback (Pictures)
1: Mosaic-pattern noise appears on images
during cue or review playback.
• This phenomenon is characteristic of digital
video systems. It is not a malfunction.
2: Horizontal stripes appear on images during
cue and review playback.
Playback (Sound)
1: Sound is not played back from the built-in
speaker of the Camcorder or the
headphones.
0 Is the volume too low? During playback, push
the [s /VOLr] lever to display the volume
indication and adjust it. (-41-)
• Horizontal stripes may appear depending on
the scene, but this is not a malfunction.
2: Different sounds are reproduced at the
same time.
71
LSQT0862
Others
3: Although the Camcorder is correctly
Others
connected to a TV, playback images cannot
be seen.
1: The indication disappears, the screen is
frozen, or no operation can be performed.
• Turn off the power to the Camcorder. If the
power cannot be turned off, press the [RESET]
button, or detach the battery or AC adaptor and
then reattach it. After that, turn on the power
again. If normal operation is still not restored,
detach the power connected, and consult the
dealer who you purchased the Camcorder
from.
2: “PUSH THE RESET SWITCH” is displayed.
• An irregularity in the Camcorder has been
automatically detected. Remove the cassette
or the card for data protection and then press
the [RESET] button with the boss A. The
Camcorder will be activated.
• Have you selected video input on the TV?
Please read the operating instructions of your
TV and select the channel that matches the
input terminals used for the connection.
4: Playback picture is not clear.
• Are the heads of the Camcorder dirty? If the
heads are dirty, playback image cannot be
clear. Clean the heads by using the head
cleaner for digital video (optional). (-74-)
• If the terminal for the AV cable is soiled, noises
may appear on the screen. Wipe the soil off the
terminal with a soft cloth, and then connect the
cable to the AV terminal.
• Is a picture containing a copyright protection
signal (copy guard) being recorded? When a
protected picture is played back by the
Camcorder, mosaic-like patterns appear on the
picture.
RESET
Card
1: Recorded pictures are not clear.
• Have you set [BASIC] >> [PICT. QUALITY] >>
A
[
pictures with fine details may include a
mosaic-like pattern. Set [PICT. QUALITY] >>
].
],
• If you do not press the [RESET] button, the
power to the Camcorder is turned off
automatically about 1 minute later.
[
• Even after you press the [RESET] button, the
indication may still appear repeatedly. If so, the
Camcorder needs repair. Detach the power
connected, and consult the dealer who you
purchased the Camcorder from. Do not attempt
to repair the unit by yourself.
3: Even if connected by the USB cable, the
Camcorder is not recognized by the PC.
• Is the USB driver installed?
4: When the USB cable is disconnected, an
error message will appear on PC.
• To disconnect the USB cable safely,
double-click the [ ] icon in the task tray and
follow the instructions on the screen.
5: The Camcorder malfunctions on editing,
dubbing from digital video equipment, or
using “MotionDV STUDIO 5.3E LE for DV”.
• If a tape is recorded in multiple modes such as
SP and LP (recording mode), 12bit and 16bit
(sound recording mode), normal and wide,
recorded and unrecorded parts, the Camcorder
may malfunction at a point where the mode
switches. When you edit, do not record in
multiple modes.
(-31-)
2: A file recorded on a card cannot be deleted.
• Is the file locked? Locked files cannot be
deleted. (-45-)
• For the SD Memory Card, if its write protect
switch is set to [LOCK], then deletion is
disabled. (-19-)
3: Photoshot playback images do not look
normal.
• The picture may be damaged. In order to
prevent the loss of image data, backing up on a
cassette or a personal computer is
recommended.
4: Even if a card is formatted, it cannot be
used.
• Either the Camcorder or the card may be
damaged. Please consult a dealer.
5: During playback, [UNPLAYABLE CARD] is
displayed.
• The image was either recorded in a different
format, or data is damaged.
72
LSQT0862
Others
6: The warning/alarm indication [°] appears
when the Camcorder is operated in the WEB
camera mode.
• Did you press the menu button or the recording
start/stop button? You cannot use the menu or
record onto the tape/card in the WEB camera
mode.
• Is the setting for the remote control correct?
• Did you attempt to play a tape without inserting
it? Insert a tape.
Cautions for Use
ª About condensation
If you turn the Camcorder on when condensation
occurs on the head or the tape, condensation
Indication [3] (yellow or red) is displayed on the
viewfinder or the LCD monitor and the messages
[3DEW DETECT] or [3EJECT TAPE] (only
when the tape is inserted) appear. If so, follow the
procedure below.
• Did you attempt to play a tape with copyright
protection (copy guard)? Pictures of the tape
with copyright protection (copy guard) cannot
be displayed on the PC. (The audio of the tape
can be played.)
3 in yellow:
Dew is slightly adhering on the head or the tape.
3 in red:
Dew is adhering on the head or the tape.
1 Remove the tape if it is inserted.
≥It takes about 20 seconds to open the
cassette holder. This is not a malfunction.
2 Leave the Camcorder with the cassette
cover closed to cool or warm it to the
ambient temperature.
• Is the video stream driver installed?
When [3] in yellow
≥You cannot use the Tape Recording/
Playback Mode. Leave the Camcorder for
about 30 minutes.
≥However, you can use the Card Recording
Mode or Picture Playback Mode when a
cassette is not inserted.
When [3] in red
≥The power Lamp blinks for about 1 minute
and then the Camcorder automatically turns
off. Leave it for about 2 to 3 hours.
3 Turn the Camcorder on again, set it to the
Tape Recording/Playback Mode and then
check if the condensation indication
disappears.
Especially in cold areas, moisture may be frozen.
If so, it may take more time before the
condensation indication disappears.
Watch for condensation even before the
condensation Indication is displayed.
≥The condensation indication may not appear
depending on circumstances. When
condensation occurs on the lens or the
Camcorder, it may also occur on the head and
the tape. Do not open the cassette cover.
When the lens is fogged:
Set the [OFF/ON] switch to [OFF] and leave the
Camcorder in this condition for about 1 hour.
When the lens temperature becomes close to the
ambient temperature, the fogging disappears
naturally.
73
LSQT0862
Others
ª About dirty heads
ª About the Camcorder
If video heads (the parts that closely contact
with the tape) become dirty, normal recording
and playback are not properly performed.
Clean the heads with the digital video head
cleaner.
≥When the Camcorder is used for a long time,
the Camcorder body becomes warm, but this is
not a malfunction.
Keep the Camcorder away from magnetized
equipment such as a cellular phones,
microwave ovens, TVs, and video game
equipment.
≥If you use the Camcorder on or near a TV,
images or sounds may be disturbed due to
electromagnetic wave radiation.
≥Insert the head cleaner into the Camcorder, set
it to the Tape Playback Mode, and play it back
for about 10 to 20 seconds. (If you do not stop
the playback, it automatically stops about
30 seconds later.)
≥We recommend cleaning the heads periodically.
If the heads become dirty, “NEED HEAD
CLEANING” appears during recording. During
playback, moreover, the following symptoms
appear.
≥Recordings on the tape may be damaged, or
images may be distorted, by strong magnetic
fields created by speakers or large motors.
≥Electromagnetic wave radiation generated by
digital circuits including microprocessor may
adversely affect the Camcorder, causing the
disturbance of images and sounds.
≥Mosaic-like noise appears partially or the
sound is interrupted.
≥Black or blue mosaic-like horizontal stripes
appear.
When normal playback cannot be performed
even after the head cleaning
One possible cause is that normal recording
could not be performed because the heads were
dirty at the time of recording. Clean the heads,
and perform recording and playback again. If
normal playback can be performed, the heads are
clean. Before an important recording, be sure to
conduct a test recording to make sure that normal
recording can be performed.
≥If the heads become dirty soon after cleaning,
the problem may be the tape. If so, try another
cassette.
≥During playback, the picture or sound may be
interrupted momentarily, but this is not a
malfunction of the Camcorder. (One possible
cause is that the playback is interrupted by dirt
or dust that momentarily adheres to the heads.)
≥If the Camcorder is affected by such equipment
and does not function properly, turn off the
Camcorder power and detach the battery or AC
adaptor. Then, connect the battery or AC
adaptor again and turn on the Camcorder
power.
Do not use your Camcorder near radio
transmitters or high-voltage cables.
≥If you record pictures near radio transmitters or
high-voltage cables, recorded images or sounds
may be adversely affected.
Do not spray insecticides or volatile
chemicals onto the Camcorder.
≥If the Camcorder is sprayed with such
chemicals, the Camcorder body may become
deformed and the surface finish may peel off.
≥Do not keep rubber or plastic products in
contact with the Camcorder for a long time.
When you use your Camcorder in a sandy or
dusty place such as on a beach, do not let
sand or fine dust get into the body and
terminals of the Camcorder. Also, protect the
Camcorder from getting wet.
≥Sand or dust may damage the Camcorder or
cassette. (Care should be taken when inserting
and removing a cassette.)
≥If sea water splashes onto the Camcorder, wet
a soft cloth with tap water, wring it well, and use
it to wipe the Camcorder body carefully. Then,
wipe it again thoroughly with a soft dry cloth.
While carrying the Camcorder, do not drop or
bump it.
≥A strong impact on the Camcorder may break its
housing, causing it to malfunction.
74
LSQT0862
Others
If you drop the battery accidentally, check to
Do not use benzine, paint thinner or alcohol
for cleaning the Camcorder.
see if the terminals are deformed.
≥Before cleaning, detach the battery or pull out
the AC mains lead from the AC mains socket.
≥The Camcorder body may be discoloured and
the surface finish may peel off.
≥Wipe the Camcorder with a soft dry cloth to
remove dust and fingerprints. To remove
stubborn stains, wring well a cloth that is soaked
in a neutral detergent diluted with water and
wipe the Camcorder with it. Afterwards, wipe it
with a dry cloth.
≥Attaching a deformed battery to the Camcorder
or AC adaptor may damage the Camcorder or
AC adaptor.
After use, be sure to take the cassette out and
detach the battery from the Camcorder or pull
out the AC mains lead from AC mains socket.
≥The battery should be stored in a cool place free
from humidity, with as constant temperature as
possible. (Recommended temperature: 59oF to
77oF (15oC to 25oC), Recommended humidity:
40% to 60%)
≥Extremely high temperatures or low
temperatures will shorten the life of the battery.
≥If the battery is kept in a high-temperature,
high-humidity, or oily-smoky places, the
terminals may rust and cause malfunctions.
≥To store the battery for a long period of time, we
recommend you charge it once every year and
store it again after you have completely used up
the charged capacity.
≥When you use a chemical dust cloth, follow the
instructions.
Do not use this Camcorder for surveillance
purposes or other business use.
≥If you use the Camcorder for a long time, the
internal temperature increases and,
consequently, this may cause malfunction.
≥This Camcorder is not intended for business
use.
About the flash
≥Since there are high-voltage sections inside the
flash, do not disassemble it to avoid electric
shock.
≥Dust and other matter attached to the battery
terminals should be removed.
Do not throw old battery into fire.
≥Heating a battery or throwing it into a fire may
result in an explosion.
ª About the battery
The battery used in the Camcorder is a
rechargeable lithium ion battery. This battery is
susceptible to temperature and humidity, and the
effect of temperature increases with increasing or
decreasing temperature. In the low temperature
range, the fully charged indication may not
appear, or the low battery indication may appear
about 5 minutes after the start of use. At high
temperature, moreover, the protection function
may work, disabling use of the Camcorder.
Be sure to detach the battery after use
≥If the battery is left attached to the Camcorder, a
minute amount of current is consumed even
when the Camcorder power is [OFF]. If the
battery is left attached to the Camcorder for a
long time, over-discharge takes place. The
battery may become unusable after it is
charged.
≥If the operating time is very short even after the
battery has been recharged, the battery has
worn out. Please purchase a new battery.
ª About the AC adaptor
≥If the battery is warm, charging requires more
time than normal.
≥If the temperature of the battery is extremely
high or extremely low, the [CHARGE] lamp may
continue flashing, and the battery may not be
charged. After the battery temperature has
decreased or increased sufficiently, recharging
starts automatically. So, wait for a while. If the
lamp still continues flashing even after the
recharging, the battery or AC adaptor may be
faulty. If so, please contact a dealer.
≥If you use the AC adaptor near a radio, radio
reception may be disturbed. Keep the AC
adaptor 3 feet (1 m) or more away from radio.
≥When using the AC adaptor, it may generate
whirring sounds. However, this is normal.
≥After use, be sure to pull out the AC mains lead
from the AC mains socket. (If they are left
connected, a minute amount of current is
consumed.)
Prepare spare batteries when going out for
recording.
≥Prepare batteries appropriate to 3 to 4 times the
period during you want to record pictures in. In
cold places such as a ski resort, the period
during which you can record pictures is
shortened.
≥When you travel, do not forget to bring an AC
adaptor so that you can recharge the batteries
at your destination.
≥Always keep the electrodes of the AC adaptor
and battery clean.
75
LSQT0862
Others
ª About the cassette
ª About the card
Never place the cassette in a high temperature
place.
When inserting or removing the card, always
set the [OFF/ON] switch to [OFF].
When the access lamp is illuminated (During
access to the card), do not open the card slot
cover to pull out the card, turn off the power,
or cause any vibrations or impact.
Do not leave the card in places where there is
high temperature or direct sunlight, or where
electromagnetic waves or static electricity are
easily generated. Moreover, do not fold or
drop the card.
≥The tape may be damaged, producing
mosaic-like noise at the time of playback.
When storing the cassette after use, be sure
to rewind the tape to the beginning and take it
out.
≥If the cassette is left for more than 6 months
(depending on the storage condition) in the
Camcorder or stopped midway, the tape may
sag and be damaged.
≥Once every 6 months, wind the tape to the end
and then rewind it to the beginning. If the
cassette is left for 1 year or longer without
winding or rewinding, the tape may be deformed
by expansion or shrinkage attributable to
temperature and humidity. The wound tape may
stick to itself.
≥Dust, direct sunlight (ultraviolet rays), and
humidity may damage the tape. Such usage
may cause damage to the Camcorder and the
heads.
≥After use, be sure to rewind the tape to the
beginning, put the cassette in the case to
protect it from dust, and store it upright.
Keep the cassette away from strong
magnetism.
≥Objects using magnets such as magnetic
necklaces and toys having a magnetic force that
is stronger than expected, may erase the
contents of a recording or may increase noise.
≥The card may break or the contents of the card
may be destroyed or erased.
After use, be sure to remove the card from the
Camcorder for storage.
≥After use, or when storing or carrying the card,
put it in the storage case.
≥Do not allow dust, water, or foreign substances
to adhere to the terminals on the back of the
card. Moreover, do not touch the terminals with
your hand.
≥Keep the Memory Card out of reach of children
to prevent swallowing.
ª Folder structure of the card
The folder structure of the card formatted by
the Camcorder will be displayed on the PC as
the illustration below.
256
≥Up to 999 pictures can be recorded on
100CDPFP folder etc.
≥Files with the DPOF settings can be recorded
on MISC folder.
76
LSQT0862
Others
ª LCD monitor/Viewfinder
LCD monitor
Explanation of terms
≥When the LCD monitor gets dirty, wipe it with a
dry soft cloth.
ª Automatic white balance
White balance adjustment recognizes the color of
light and adjusts so the white color will become a
pure white. The Camcorder determines the hue of
light that comes through the lens and white
balance sensor, thereby judging the recording
condition, and selects the closest hue setting.
This is called automatic white balance
≥In a place with drastic temperature changes,
condensation may form on the LCD monitor.
Wipe it with soft dry cloth.
≥If your Camcorder is extremely cold, the LCD
monitor is slightly darker than usual immediately
after you turn the power on. However, as the
internal temperature increases, it goes back to
normal brightness.
adjustment. However, since the Camcorder only
stores white color information under several light
sources, automatic white balance adjustment
does not function normally under the other light
sources.
Extremely high precision technology is
employed to produce the LCD monitor
screen featuring a total of approximately
113,000 pixels. The result is more than
99.99% effective pixels with a mere 0.01% of
the pixels inactive or always lit. However,
this is not a malfunction and does not affect
the recorded picture.
2)
10 000K
9
8
000K
000K
3)
7
6
000K
000K
4)
5)
5
4
000K
000K
6)
1)
7)
Viewfinder
3
000K
≥To remove dust from inside the viewfinder,
dismount the viewfinder first. When the dust is
difficult to remove, get rid of it with a cotton
swab dampened with water. Then wipe the
viewfinder with a dry cotton swab.
≥To clean the inside of the viewfinder, keep
pressing 1 and hold the eyecup 2 and pull it
out.
8)
9)
2
1
000K
000K
10)
Outside of the effective range of automatic white
balance adjustment, the image will become
reddish or bluish. Even within the effective range
of automatic white balance adjustment, the
automatic white balance adjustment may not
function properly if there is more than one light
source. For light outside the functional auto white
balance adjustment range, use the manual white
balance adjustment mode.
2
1
Extremely high precision technology is
employed to produce the viewfinder screen
featuring a total of approximately 113,000
pixels. The result is more than 99.99%
effective pixels with a mere 0.01% of the
pixels inactive or always lit. However, this is
not a malfunction and does not affect the
recorded picture.
1) The effective range of automatic white
balance adjustment on this Camcorder
2) Blue sky
3) Cloudy sky (rain)
4) TV screen
5) Sunlight
6) White fluorescent lamp
7) Halogen light bulb
8) Incandescent light bulb
9) Sunrise or sunset
10) Candlelight
ª Periodical check-ups
≥To maintain the highest image quality, we
recommend replacing worn parts such as heads
after approx. 1000 hours of use. (This, however,
depends on operating conditions including
temperature, humidity and dust.)
77
LSQT0862
Others
Recording a subject with little contrast
ª White balance
≥A subject with little contrast, such as a white
wall, may become blurry because the
Camcorder achieves focus based upon the
vertical lines of an image.
The image recorded by the Camcorder may
become bluish or reddish under the influence of
light sources. To avoid such phenomena, adjust
the white balance.
White balance adjustment determines the white
color under different light sources. By recognizing
which is the white color under sunlight and which
is the white color under a fluorescent lamp, the
Camcorder can adjust the balance among the
other colors.
Since white color is the reference of all colors
(light), the Camcorder can record pictures in a
natural hue if it can recognize the reference white
color.
ª Auto focus
Auto focus automatically moves the focusing lens
forward and backward inside the Camcorder to
bring the subject into focus.
Auto focus has the following characteristics.
≥Adjusts so that the vertical lines of a subject are
seen more clearly.
≥Attempts to bring an object with higher contrast
into focus.
≥Focuses on the screen center only.
Due to these characteristics, auto focus does not
work correctly in the following situations. Record
pictures in the manual focus mode.
Recording a subject with one end located
closer to the Camcorder and the other end
farther away from it
≥As auto focus adjusts at the center of an
image, it may be impossible to focus on a
subject that is located in both the foreground
and background.
Recording a subject behind dirty or dusty
glass
≥The subject behind the glass will not be
focused because the focus is on the dirty
glass.
Recording a subject that is surrounded by
objects with glossy surfaces or by highly
reflective objects
≥The recording subject may become blurry
because the Camcorder focuses on the
objects with glossy surfaces or on highly
reflective objects.
Recording a subject in dark surroundings
≥The Camcorder cannot focus correctly
because the light information that comes
through the lens decreases considerably.
Recording a fast-moving subject
≥As the focus lens-inside moves mechanically,
it cannot keep up with a fast-moving subject.
78
LSQT0862
Others
Mic input:
Mic sensitivity –50 dB (0 dB=1 V/Pa, 1 kHz) (Stereo
mini jack)
USB:
Specifications
Digital Video Camcorder
Card reader/writer function, USB 2.0 compliant
(Hi-Speed)
Information for your safety
No copyright protection support
PictBridge-compliant
Power source:
DC 7.9/7.2 V
Power consumption:
Recording
Digital interface:
DV input/output terminal (IEEE1394, 4-pin)
Video flash:
GN 5.5
Dimensions:
Approx. 3.2 inch (W) k2.9 inch (H) k5.7 inch (D)
Approx. 81 mm (W) k73 mm (H) k144 mm (D)
Weight:
Approx. 1.1 lbs (500 g)
(without battery, DV cassette and lens cap)
Operating temperature:
32oF–104oF (0oC–40oC)
Operating humidity:
10%–80%
6.0 W
Recording format:
Mini DV (Consumer-use digital video SD format)
Tape used:
6.35 mm digital video tape
Recording/playback time:
SP: 80 min; LP: 120 min (with DVM80)
Video
Recording system:
Digital component
Television system:
EIA Standard: 525 lines, 60 fields NTSC color signal
Audio
Recording system:
PCM digital recording
16 bit (48 kHz/2 ch), 12 bit (32 kHz/4 ch)
Image sensor:
1/6-inch 3CCD image sensor
(Effective pixels: moving picture/640 Kk3, still
picture/710 Kk3, Total: 800 Kk3)
Lens:
Auto iris, F1.6, Focal length; 2.85–28.5 mm, Macro
(Full range AF)
Filter diameter:
43 mm
Zoom:
Card memory functions
Recording media:
SD Memory Card (32 MB/64 MB/128 MB/256 MB/
512 MB/1 GB)
Still picture recording file format:
JPEG (Design rule for Camera File system, based
on Exif 2.2 standard), DPOF corresponding
Still picture size:
Mega pixel recording:
2048k1512
1600k1200
1280k960
VGA recording: 640k480
WEB camera
compression:
Motion JPEG
Image size:
320k240 pixels (QVGA)
Frame rate:
10:1 Power zoom
Monitor:
2.5-inch LCD
Viewfinder:
Approx. 6 fps
Color electronic viewfinder
Microphone:
Stereo (with a zoom function)
Speaker:
1 round speaker ‰ 20 mm
Standard illumination:
1,400 lx
Minimum required illumination:
1 lx (MagicPix Mode)
Video output level:
AC adaptor
Information for your safety
Power source:
AC 110–240 V, 50/60 Hz
Power consumption:
19 W
DC output:
DC 7.9 V, 1.4 A (Camcorder operation)
DC 8.4 V, 0.65 A (Battery charging)
1.0 Vp-p, 75 ohm
S-Video output level:
Y Output: 1.0 Vp-p, 75 ohm
C Output: 0.286 Vp-p, 75 ohm
Audio output level (Line):
316 mV, 600 ohm
Dimensions:
2.40 inch (W) k1.26 inch (H) k3.58 inch (D)
61 mm (W) k32 mm (H) k91 mm (D)
Weight:
Video input level:
1.0 Vp-p, 75 ohm
Approx. 0.24 lbs. (110 g)
S-Video input level:
Y Input: 1.0 Vp-p, 75 ohm
C Input: 0.286 Vp-p, 75 ohm
Audio input level (Line):
316 mV, 10 kohm or more
Weight and dimensions are approximate values.
Specifications may change without prior notice.
79
LSQT0862
Others
Maximum number of still pictures recordable on an SD Memory Card (optional)
PICTURE
SIZE
[640]
[1280]
[1600]
[2048]
PICTURE
QUALITY
32 MB
64 MB
128 MB
256 MB
512 MB
1 GB
220
440
440
880
47
98
76
158
30
63
47
98
18
39
29
62
880
1760
3520
7040
187
390
774
1550
302
121
252
502
1006
187
390
774
1550
75
119
248
493
989
1760
3520
7040
628
158
314
629
1246
2495
14080
≥The numbers shown in the table are approximations.
≥These figures vary depending on the subject being photographed.
80
LSQT0862
Others
Camcorder Accessory System
Description
Accessory#
Figure
PV-DAC14
AC adaptor with AC Cable
and DC Cables
*CGR-DU06A/1B
*CGA-DU12A/1B
640 mAh/Rechargeable
Lithium Ion Battery Pack
1150 mAh/Rechargeable
Lithium Ion Battery Pack
*CGA-DU21A/1B
2040 mAh/Rechargeable
Lithium Ion Battery Pack
PV-DDC9 (For USA)
PV-DDC9-K (For Canada)
DV Interface Cable (i.LINK)
(4-pin to 4-pin)
RP-SDH01GU1A
RP-SDH512U1A
RP-SDH256U1A/W
RP-SD128BU1A/W
RP-SD064BPPA/W
RP-SD032BPPA
1 GB SD Memory Card
512 MB SD Memory Card
256 MB SD Memory Card
128 MB SD Memory Card
64 MB SD Memory Card
32 MB SD Memory Card
USB Reader/Writer for
SD Memory Card
(compatible with MultiMediaCard)
BN-SDCAPE/1B (For USA)
BN-SDCAPU/1B (For Canada)
BN-SDABPE/1B (For USA)
BN-SDABPU/1B (For Canada)
SD PCMCIA Adaptor
(compatible with MultiMediaCard)
N2QCBD000030
Magic Wire Remote Control
with Narration Mic
VW-LDC10
Video DC Light (10 W)
(CGA-DU07 is necessary to activate it.)
VW-LDH3
Video DC Light (3 W)
Stereo Zoom Microphone
Carrying Case
VW-VMH3
PV-HB002 (USA only)
*Please refer to page -17-, concerning the battery charging time and available recording time.
*NOTE: Accessories and/or model numbers may vary by country. Please consult your local
dealer.
81
LSQT0862
Others
Camcorder Accessory Order Form (For USA Customers)
Please photocopy this form when placing an order.
1. Palmcorder Model #
2. Items Ordered
Accessory #
Description
Price Each
Quantity
Total Price
Subtotal
Your State & Local Sales Tax
Shipping & Handling
Total Enclosed
6.95
3. Method of payment (check one)
Check of Money Order enclosed (NO C.O.D.SHIPMENTS)
VISA
Credit Card #
MasterCard
Discover
Expiration Date
Customer Signature
Make Check or Money Order Payable to: PANASONIC ACCESSORIES
(Please do not send cash)
4. Shipping information (UPS delivery requires complete street address)
Ship To:
Mr.
Mrs.
Ms.
Phone#:
First
Last
Day
(
)
)
Street Address
City
Night
(
State
Zip
TO OBTAIN ANY OF OUR PALMCORDER ACCESSORIES YOU CAN DO ANY OF
THE FOLLOWING:
VISIT YOUR LOCAL PANASONIC DEALER
OR
CALL PANASONIC’S ACCESSORY ORDER LINE AT 1-800-332-5368
[6 AM-5 PM M-F, 6 AM-10:30 AM SAT, PACIFIC TIME]
OR
MAIL THIS ORDER TO: PANASONIC SERVICES COMPANY ACCESSORY ORDER OFFICE
20421 84th Avenue South Kent, WA. 98032
In CANADA, please contact your local Panasonic dealer for more information on Accessories.
82
LSQT0862
Others
Request for Service Notice (USA Only)
Please photocopy this form when making a request for service notice, in the
unlikely event this product needs service.
Request for Service Notice:
•Please include your proof of purchase.
(Failure to do so will delay your repair.)
•To further speed your repair, please provide
an explanation of what is wrong with the unit
and any symptom it is exhibiting.
Mail this completed form and your Proof of Purchase along with your unit to:
Panasonic Services Company
1705 N. Randall Road
Elgin, IL. 60123-7847
Attn: Camcorder Repair
83
LSQT0862
Others
Limited Warranty (For USA Customers)
PANASONIC CONSUMER ELECTRONICS
COMPANY, DIVISION OF PANASONIC
CORPORATION OF NORTH AMERICA
One Panasonic Way, Secaucus, New Jersey 07094
PANASONIC PUERTO RICO, INC.
Ave. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Panasonic/Quasar Video Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Electronics Company or
Panasonic Puerto Rico, Inc. (collectively referred to as “the warrantor”) will, for the length of the period indicated on the chart below,
which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with new or refurbished
parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.
Product
Parts
Labor
Contact Number
Service
Ninety (90) Days
Ninety (90) Days
One (1) Year (except CCD Image Sensor)
CCD Image Sensor - 6 (Six) Months
1-800-211-PANA(7262)
Carry-In or Mail-In
Camcorder
DVD/VCR Deck,
A/V Mixer
One (1) Year
Ninety (90) Days
Carry-In or Mail-In
1-800-211-PANA(7262)
1-800-211-PANA(7262)
Carry-In: 21”
TV/VCR, TV/DVD,
TV/DVD/VCR
Combination
Ninety (90) Days
Ninety (90) Days
CRTand Smaller
In-Home or Carry-In:
22” CRT and Larger
One (1) Year (except CRT)
CRT - Two (2) Years
One (1) Year (except CRT)
CRT - Two (2) Years
Ninety (90) Days
Ninety (90) Days
TV/HDR
Combination
1-888-843-9788
In-Home or Carry-In
Rechargeable
Batteries
(in exchange for
defective item)
Ten (10) Days
Not Applicable
Carry-In or Mail-In
1-800-211-PANA(7262)
Tape
(in exchange for
defective item)
Five (5) Days
Not Applicable
Not Applicable
Carry-In or Mail-In
Carry-In or Mail-In
1-800-211-PANA(7262)
1-800-211-PANA(7262)
Memory Cards
(in exchange for
defective item)
Ninety (90) Days
During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts.
You must carry-in or mail-in your product or arrange for in-home service, as applicable, during the warranty period. If non-rechargeable
batteries are included, they are not warranted. This warranty only applies to products purchased and serviced in the United States or
Puerto Rico. This warranty is extended only to the original purchaser of a new product which was not sold “as is”. A purchase receipt or
other proof of the original purchase date is required for warranty service.
Carry-In, Mail-in or In-Home Service
For Carry-In, Mail-In or In-HomeService (as applicable) in the United States call toll free contact number listed above or visit Panasonic
For assistance in Puerto Rico call Panasonic Puerto Rico, Inc. (787)-750-4300 or fax (787)-768-2910.
In-Home service, if applicable, requires clear, complete and easy access to the product by the authorized servicer and does not include
removal or re-installation of an installed product. It is possible that certain in-home repairs will not be completed in-home, but will require
that the product, or parts of the product, be removed for shop diagnosis and/or repair and then returned.
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or
cosmetic damage, nor does it cover markings or retained images on the picture tube resulting from viewing fixed images (including,
among other things, letterbox pictures on standard 4:3 screen TV’s, or non-expanded standard 4:3 pictures on wide screen TV’s, or
onscreen data in a stationary and fixed location). The warranty ALSO DOES NOT COVER damages which occurred in shipment, or
failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect,
mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper
maintenance, power line surge, lightning damage, modification, or commercial use (such as in a hotel, office, restaurant, or other
business), rental use of the product, service by anyone other than a Factory Servicenter or other Authorized Servicer, or damage that is
attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THIS PRODUCT, OR ARISING OUT OF ANYBREACH OF THIS WARRANTY.
(As examples, this excludes damages for lost time, cost of having someone remove or re-install an installed unit if applicable, or travel
to and from the servicer, loss of media or images, data or other memory or recorded content. The items listed are not exclusive, but are
for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE
LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied
warranty lasts, so the exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights
which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer
or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’s Consumer Affairs Department at the
addresses listed for the warrantor.
PARTS AND SERVICE (INCLUDING COST OF AN IN-HOME SERVICE CALL, WHERE APPLICABLE) WHICH
ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR RESPONSIBILITY.
84
LSQT0862
Others
Customer Services Directory
Service in Canada: As per Sevicenter listed in Canadian warranty information on page -86-.
Obtain Product Information and Operating Assistance; locate your nearest Dealer
or Servicenter; purchase Parts and Accessories; or make Customer Service and
Literature requests by visiting our Web Site at:
or, contact us via the web at:
You may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST
For hearing or speech impaired TTY users, TTY : 1-877-833-8855
Accessory Purchases
Purchase Parts, Accessories and Instruction Books online for all Panasonic Products
by visiting our Web Site at:
or, send your request by E-mail to:
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday – Friday 9 am to 8 pm, EST.)
Panasonic Services Company
20421 84th Avenue South,
Kent, WA 98032
(We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY : 1-866-605-1277
Product Repairs
Centralized Factory Servicenter
Panasonic Services Company
1705 N. Randall Road,
MAIL TO:
Elgin, IL 60123-7847
Attention: Camcorder Repair
Please carefully pack and ship, prepaid and insured, to the Elgin Centralized Factory Servicenter
Customer’s in Puerto Rico, please ship or carry in to location below (“Service in Puerto Rico”).
Service in Puerto Rico
Panasonic Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Phone (787)750-4300, Fax (787)768-2910
As of November 2004
85
LSQT0862
Others
Warranty (For Canadian Customers)
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
PANASONIC PRODUCT – LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship and
agrees to remedy any such defect for a period as stated below from the date of original purchase.
Camcorder Product – One (1) year, parts and labour
LIMITATIONS AND EXCLUSIONS
This warranty does not apply to products purchased outside Canada or to any product which has been
improperly installed, subjected to usage for which the product was not designed, misused or abused,
damaged during shipping, or which has been altered or repaired in any way that affects the reliability or
detracts from the performance, nor does it cover any product which is used commercially. Dry cell
batteries are also excluded from coverage under this warranty.
This warranty is extended to the original end user purchaser only. A purchase receipt or other proof of
date of original purchase is required before warranty service is performed.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE.
IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions
may not be applicable.
WARRANTY SERVICE
For product operation and information assistance, please contact your Dealer or our Customer
Care Centre at:
Telephone #: (905) 624-5505
Fax #: (905) 238-2360
For product repairs, please contact one of the following:
≥Your Dealer who will inform you of an authorized Servicentre nearest you.
≥A Panasonic Factory Servicentre listed below:
Richmond, British Columbia
Panasonic Canada Inc.
12111 Riverside Way
Richmond, BC
Calgary, Alberta
Mississauga, Ontario
Panasonic Canada Inc.
5770 Ambler Dr.
Mississauga, ON
L4W 2T3
Lachine, Québec
Panasonic Canada Inc.
3075, rue Louis A. Amos
Lachine, QC
Panasonic Canada Inc.
th
6835-8 St. N. E.
Calgary, AB
T2E 7H7
V6W 1K8
H8T 1C4
Tel: (604) 278-4211
Fax: (604) 278-5627
Tel: (403) 295-3955
Fax: (403) 274-5493
Tel: (905) 624-8447
Fax: (905) 238-2418
Tel: (514) 633-8684
Fax: (514) 633-8020
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in the original carton.
Include details of the defect claimed, and proof of date of original purchase.
86
LSQT0862
Others
Index
ª Numerics
ª A
AC Adaptor ..............................................17, 75
Aperture .........................................................40
ª B
ª C
Customer Services Directory .........................85
ª D
Date/Time Setting ..........................................23
ª E
ª F
ª I
Slow Motion Playback ................................... 42
Sound Volume ............................................... 41
ª V
Image stabilizer function ................................36
ª L
Web Camera ................................................. 53
White Balance ............................................... 38
Wide Function ............................................... 36
Wind noise reduction function ....................... 34
ª Z
Limited Warranty (Canada) ............................86
Limited Warranty (USA) .................................84
ª M
Magic Wire Remote Control with Narration
Mic ...............................................................26
MagicPix Function .........................................33
Manual Focus ................................................39
Mode Dial .......................................................20
MotionDV STUDIO ........................................56
Zoom ............................................................. 31
Zoom Microphone ......................................... 32
87
LSQT0862
Others
3 Apriete la marca [PUSH] 1 a fin de cerrar el
compartimiento del cassette.
Spanish Quick Use Guide/
Guía española para el uso rápido
ª Carga de la batería
1 Conecte el cable eléctrico de CA al
adaptador de CA y a la toma de la red de
CA.
1
PUSH
2 Meta la batería en el respectivo soporte
alineando la marca, luego encájela.
4 Sólo cierre la tapa del cassette después de
que el respectivo compartimiento esté
cabalmente alojado.
ª Insertar/quitar una tarjeta
1 Abra el monitor LCD, luego abra la tapa de
la ranura de la tarjeta.
ª Montaje de la batería
Empuje la batería contra el porta batería y hágala
deslizar hasta que dispare.
2 Inserte/quite la tarjeta en/de la ranura.
1
ª Insertar/quitar un cassette
1 Haga deslizar la palanca [OPEN/EJECT] y
abra la tapa del cassette.
≥Cuando inserta una tarjeta, con su lado
etiquetado vuelto 1 hacia Ud., la apriete
derecha de un solo golpe hasta que tope.
≥Cuando quita la tarjeta, abra la tapa de la
respectiva ranura, apriete en el medio de la
tarjeta y tírela fuera derecha.
3 Cierre firmemente la tapa de la ranura de la
tarjeta.
ª Cómo activar la alimentación
1 Mientras que oprime el botón 1, ponga el
interruptor [OFF/ON] en [ON].
2 Una vez que el compartimiento del cassette
esté abierto, inserte/quite el cassette.
1
88
LSQT0862
Others
ª Cómo apagar la alimentación
1 Mientras que oprime el botón 1, ponga el
interruptor [OFF/ON] en [OFF].
ª Reproducción de la cinta
≥Ajuste al modo de reproducción de cinta.
1
1 Actúe en la palanca de mando.
ª Grabación en una cinta
≥Ajuste al modo de grabación de cinta.
1/;: Reproducción/Pausa
6: Rebobinado/Localización regresiva
(Vuelve para reproducir con el icono
1/;).
5: Avance rápido/Localización progresiva
(Vuelve para reproducir con el icono
1/;).
1 Oprima el botón de inicio/parada de la
grabación para empezar a grabar.
∫:
Parada
ª Reproducción de tarjeta
≥Ajuste al modo de reproducción de imagen.
2 Oprima de nuevo el botón de inicio/parada
de la grabación para detener brevemente la
grabación.
;
1 Actúe en la palanca de mando.
ª Grabación de imágenes fijas en una
tarjeta (Photoshot)
≥Ajuste al modo de grabación de tarjeta.
PC
E:
Reproducción de la imagen anterior.
Reproducción de la siguiente imagen.
D:
1/∫: Diapositiva (Reproduce por orden las
imágenes fijas en la tarjeta), inicio/parada
1 Oprima el botón [PHOTO SHOT].
PHOTO
SHOT
89
LSQT0862
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ 07094
Panasonic Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3
P
LSQT0862 A
© 2004 Matsushita Electric Industrial Co., Ltd.
S1204Nm0
|