Panasonic AK HC900 User Manual

Panasonic Broadcast  
AK-HC900  
Menu Information  
Setting of Menu Items  
_ Configuration of menu display screen  
USER MENU  
Maintenance menu  
1.MAINTENANCE  
2.SETTING  
3.CAM ID  
MAINTENANCE  
°
°
1.BLACK SHADING  
2.PED,GAMMA,FLARE  
3.KNEE,WHITE CLIP  
4.R/B GAIN  
4.FILE MENU  
5.DTL  
6.GAIN,AUTO IRIS  
7.S.GAIN 1  
8.S.GAIN 2  
9.S.GAIN 3  
10.FRAME MODE  
11.COLOR CORRECTION1  
12.COLOR CORRECTION2  
USER MENU  
Using condition setting menu  
°°SETTING°°  
1.MODE  
2.SHUTTER  
3.H.PHASE  
Camera ID setting menu  
°°CAM ID°°  
ID:AKHC900  
File managing & renewing menu  
H FILE MENU  
°
°
FILE  
:USER1  
:PRESET)  
:USER1  
:
(DATA REF  
SAVE FILE?  
SAVE  
18  
Setting of Menu Items  
_ USER menu (Initial screen)  
USER MENU  
The readout data at start of power supply is  
the data just before cutting off the power  
supply, and the operation is started with the  
data.  
1. MAINTENANCE  
It sets various adjusting data.  
2. SETTING  
1.MAINTENANCE  
2.SETTING  
3.CAM ID  
4.FILE MENU  
It sets various modes.  
3. CAM ID  
It sets the camera ID.  
4. FILE MENU  
It executes file loading and saving, and  
makes the basic setting of data display.  
Menu operation is executed by the HD Controller AK-HRP900.  
19  
Setting of Menu Items  
! Maintenance menu  
MAINTENANCE  
Move the cursor (arrow mark) to the item  
to be adjusted and press the MENU key,  
then it enters the adjustment menu there-  
under.  
Move the cursor to MAINTENANCE and  
press the MENU key, then it returns to  
USER MENU.  
°
°
1.BLACK SHADING  
2.PED,GAMMA,FLARE  
3.KNEE,WHITE CLIP  
4.R/B GAIN  
5.DTL  
6.GAIN,AUTO IRIS  
7.S.GAIN 1  
8.S.GAIN 2  
9.S.GAIN 3  
10.FRAME MODE  
11.COLOR CORRECTION1  
12.COLOR CORRECTION2  
1 Black shading correction menu  
When MENU key is pressed at DE-  
TECTION, (BLK-SHD:ACTIVE) ap-  
pears, then the lens is automatically  
stopped down and ABB operation is  
executed.  
BLACK SHADING  
°
°
DETECTION  
CORRECT(DIG)  
:ON  
When CORRECT (DIG) is turned ON,  
horizontal and vertical shading correc-  
tion is automatically executed.  
When it is turned OFF, the current value  
is maintained.  
Move the cursor to BLACK SHADING”  
and press the MENU key, then it re-  
turns to MAINTENANCE MENU.  
Note:  
It takes about 90 sec. until completion of  
black shading correction.  
20  
Setting of Menu Items  
! Maintenance menu  
°°PED,GAMMA,FLARE°°  
M PED  
R PED  
B PED  
M GAMMA  
R GAMMA  
B GAMMA  
R FLARE  
G FLARE  
B FLARE  
GAMMA  
2 Pedestal, gamma, flare adjustment  
menu  
:+027  
:+000  
:+000  
:0.45  
:+00  
:+00  
:010  
:000  
:017  
:ON  
M PED: Master pedestal can be adjusted  
only by turning the control panel VR.  
The R, G, B pedestal can be totally ad-  
justed.  
R, B PED: R, B pedestal adjustment.  
Besides the master pedestal adjustment,  
R, B pedestal can be independently ad-  
justed. It is not related to DATA REF. The  
numeral display after normal ending of  
ABB is 0for both of R, B.  
FLARE  
:ON  
M GAMMA: Master gamma adjustment.  
The R, G, B gamma can be totally ad-  
justed.  
R, B GAMMA: R, B gamma adjustment.  
Besides the master gamma adjustment,  
R, B gamma can be independently ad-  
justed.  
R FLARE: R flare adjustment  
G FLARE: G flare adjustment  
B FLARE: B flare adjustment  
GAMMA: Gamma ON/OFF setting  
FLARE: Flare ON/OFF setting  
21  
Setting of Menu Items  
! Maintenance menu  
°°KNEE,WHITE CLIP°°  
3 Knee&white clip adjustment menu  
M KNEE POINT: Master knee point ad-  
justment.  
M KNEE POINT  
R KNEE POINT  
B KNEE POINT  
M KNEE SLOPE  
R KNEE SLOPE  
B KNEE SLOPE  
A.KNEE POINT  
A.KNEE LVL  
:95.00%  
:+00.00%  
:+00.00%  
:95.00%  
:+000  
:+000  
:95.00%  
:108  
G, B, R knee point can be totally adjusted.  
R, B KNEE POINT: R, B knee point ad-  
justment.  
Besides the master knee point adjust-  
ment, R, B knee point can be independ-  
ently adjusted.  
WHITE CLIP LVL  
KNEE  
WHITE CLIP  
:109%  
:MANU  
:ON  
M KNEE SLOPE: Master knee slope ad-  
justment.  
G, B, R knee slope can be totally ad-  
justed.  
R, B KNEE SLOPE: R, B knee slope ad-  
justment.  
Besides the master knee slope adjust-  
ment, R, B knee slope can be indepen-  
dently adjusted.  
A. KNEE POINT: Auto knee point setting.  
Knee point in auto knee mode is set.  
A. KNEE LVL: Auto knee level.  
WHITE CLIP LVL: White clip level ad-  
justment.  
Video level with white clipped is set.  
KNEE: KNEE mode (OFF/MANU/AUTO)  
OFF: Knee function is turned OFF  
MANU: Knee function is adjustable with  
menu.  
AUTO: Auto knee function is executed.  
WHITE CLIP: White clip operation set-  
ting.  
With it ON, white clip is effective.  
22  
Setting of Menu Items  
! Maintenance menu  
°°R/B GAIN°°  
4 Gain adjustment menu  
The gain of R, B GAIN is adjusted.  
The difference from the state of being  
white-balanced can be adjusted.  
The numeral value displayed after nor-  
mal ending of AWB is 0for both of R,  
B.  
R GAIN  
B GAIN  
:+000  
:+000  
°°DTL°°  
DTL  
5 Detail adjustment menu  
DTL: Setting of valid/invalid of detail func-  
tion.  
:ON  
:+00  
:11  
:02  
:2  
:10  
:ON  
:10  
:OFF  
:+00  
:+00  
:0  
TOTAL DTL LVL  
H DTL LVL  
CRISP  
LVL DEPENDENT  
PEEK FREQUENCY  
KNEE APERTURE  
KNEE APA.LVL  
SLIM DTL  
DTL(+)  
DTL(-)  
DTL CLIP  
DTL SOURCE  
TOTAL DTL LVL: Horizontal and verti-  
cal detail level adjustment.  
H DTL LVL: Horizontal DTL component  
is adjusted independently of DTL ad-  
justed by TOTAL DTL.  
CRISP: It functions to eliminate slight  
detail component and to reduce the noise  
level.  
:(B+G)/2  
LVL DEPENDENT: It suppresses the de-  
tail of low brightness level. The bright-  
ness level to be suppressed is adjusted  
here.  
PEAK FREQUENCY: It lifts up the detail  
component, and selects the central fre-  
quency.  
KNEE APERTURE: It functions to em-  
phasizes the detail component of the por-  
tion with knee applied.  
KNEE APA.LVL: It sets the degree of  
knee aperture.  
SLIM DTL: It validates the function of  
slimming the portion where the detail is  
thick and emphasized.  
23  
Setting of Menu Items  
! Maintenance menu  
°°DTL°°  
DTL  
5 Detail adjustment menu (continued  
from previous page)  
:ON  
DTL (i): Setting of DTL at the edge in  
positive direction.  
DTL (j): Setting of DTL at the edge in  
negative direction.  
DTL CLIP: Setting of clip level of DTL  
edge.  
DTL SOURCE: Setting of video source  
[G, R, (3G+R) /4, (2G+R+B) /4, (G+B/2)]  
to create the detail.  
TOTAL DTL LVL  
H DTL LVL  
CRISP  
LVL DEPENDENT  
PEEK FREQUENCY  
KNEE APERTURE  
KNEE APA.LVL  
SLIM DTL  
DTL(+)  
DTL(-)  
DTL CLIP  
DTL SOURCE  
:+00  
:11  
:02  
:2  
:10  
:ON  
:10  
:OFF  
:+00  
:+00  
:0  
:(B+G)/2  
°°GAIN,AUTO IRIS°°  
LOW GAIN  
MID GAIN  
HIGH GAIN  
A.IRIS LVL  
A.IRIS PEAK/AVG  
A.IRIS WINDOW  
IRIS MODE  
6 Master gain, auto iris setting menu  
LOW GAIN: LOW setting of master gain.  
MID GAIN: MID setting of master gain.  
HIGH GAIN: HIGH setting of master gain.  
The above GAIN setting is able to set -  
6 to + 18 dB in 3 dB step.  
:0dB  
:9dB  
:18dB  
:082  
:075  
:NORM1  
:LENS  
:06  
A.IRIS LVL: Setting of the intended con-  
vergence level of auto iris.  
IRIS GAIN  
A.IRIS PEAK/AVG: Setting of the detec-  
tion ratio of peak value and average value  
of the quantity of light when auto iris is  
operated.  
A.IRIS WINDOW: Setting of the detect-  
ing position of auto iris.  
IRIS MODE: Auto iris mode setting:  
(LENS/CAM).  
IRIS GAIN: Iris loop gain adjustment.  
24  
Setting of Menu Items  
! Maintenance menu  
°°S GAIN 1°°  
7 Super gain, Detail, Pedestal-offset  
level setting menu  
TOTAL GAIN  
ANLG GAIN  
:62dB  
:36dB  
:06dB  
:OdB  
:20dB  
:00  
:0  
:5  
:2  
:0.45  
:-043  
:-046  
:-045  
°
TOTAL GAIN: Total gain in analog, pixel  
addition, and memory addition is dis-  
played.  
PIX MIX  
V MIX  
FRAME MIX  
H DTL LVL  
ANLG GAIN: Gain setting in analog.  
PIX MIX: Gain setting in horizontal pixel  
addition. Capable of setting 0/6 dB.  
V MIX: Gain setting in vertical pixel addi-  
tion. Capable of setting 0/6 dB.  
FRAME MIX: Gain setting in memory ad-  
dition. Capable of setting 0/6/12/15/20  
dB.  
CRISP  
LEVEL DEPENDENT  
PEAK FREQUENCY  
M GAMMA  
MASTER PED OFFSET  
R PED OFFSET  
B PED OFFSET  
(Super gain 1, 2, 3 are same menu.)  
H DTL LVL: DTL level setting of super  
gain.  
CRISP: Setting the function of reducing  
noise level of super gain. It is invalid  
when DTL level is 0.”  
LEVEL DEPENDENT: Setting of DTL  
suppression at low lighting intensity of  
super gain.  
PEAK FREQUENCY: Setting of DTL  
boost frequency of super gain.  
M GAMMA: Gain setting in super gain.  
Capable of setting 0/6 dB.  
MASTER PED OFFSET: Setting of mas-  
ter pedestal offset of super gain 1.  
R PED OFFSET: Setting of R pedestal  
offset of super gain.  
B PED OFFSET: Setting of B pedestal  
offset of super gain.  
H FRAME MODE  
8 Setting menu in frame mode  
°
°
SCAN REVERSE: Capable of changing  
the right and left pictures, the top and bot-  
tom pictures with each other, respectively.  
1.SCAN REVERSE  
:OFF  
25  
Setting of Menu Items  
! Maintenance menu  
< COLOR CORRECTION1 >  
9 Color correction 1 menu  
Adjustment of gain (saturation) and phase  
of each color.  
SAT  
+00  
+00  
+00  
+00  
+00  
+00  
PHASE  
+00  
+00  
+00  
+00  
+00  
+00  
R
Mg  
B
Cy  
G
Y1  
< COLOR CORRECTION2 >  
qZ Color correction 2 menu  
SAT  
+00  
+00  
+00  
+00  
+00  
+00  
PHASE  
+00  
+00  
+00  
+00  
+00  
+00  
Adjustment of gain and phase of matrix.  
R - Mg  
Mg - B  
B - Cy  
Cy - G  
G - Y1  
Y1 - R  
26  
Setting of Menu Items  
@ Setting menu  
°°SETTING°°  
- Menu for various settings.  
1.MODE  
2.SHUTTER  
3.H.PHASE  
°°MODE°°  
BLACK STRETCH  
1 Camera mode setting menu  
BLACK STRETCH: Setting of the func-  
tion of expanding low-brightness analog  
video level.  
:OFF  
:OFF  
:YPbPr  
:0m  
:OFF  
:BAR  
:0  
D5600K  
ANLG OUTPUT SEL  
CABLE COMPE  
SUP GAIN  
CAM ID  
CAM ID POSI  
COLOR CORRECTION  
It is set by ON/OFF.  
D5600K: It is able to make color tempera-  
ture correction of about 5600 degrees of  
electric color temperature correcting file.  
It is set by ON/OFF.  
:OFF  
ANLG OUTPUT SEL: Video output  
YPbPr/RGB is changed over. It is usu-  
ally set to YPbPr.  
CABLE COMPE: Setting of video cable  
compensation. It is able to set 0/25/50m.  
SUP GAIN: It sets OFF/1/2/3 of MAX  
GAIN.  
CAM ID: Setting of camera ID display.  
It is set by OFF/BAR/ON.  
In BAR setting, CAM ID is displayed only  
in BAR mode.  
CAM ID POSI: It sets the display posi-  
tion of camera ID.  
0: top left, 1: top right, 2: down left, 3:  
down right.  
COLOR CORRECTION: Setting of ma-  
trix ON/OFF.  
27  
Setting of Menu Items  
@ Setting menu  
°°SHUTTER°°  
SHUTTER MODE  
SHUTTER SPEED  
SYNCHRO SCAN  
2 Electronic shutter setting menu  
SHUTTER MODE: It selects the shutter  
operation. ON/SYNCHRO/OFF can be  
selected.  
:OFF  
:1/100  
:75.1  
#
ON  
Setting of normal discrete shutter  
speed.  
SYNCHRO  
mode.  
#
Setting of synchro scan  
SHUTTER SPEED: Setting of normal  
shutter speed.  
SYNCHRO SCAN: Setting of synchro  
scan mode.  
Shutter speeds of 60 Hz to 120 Hz can  
be continuously changed.  
°°H.PHASE°°  
H.PHASE-COARSE  
3 Horizontal phase adjustment menu for  
external reference signal  
:09  
:40  
H.PHASE-COARSE: It is able to set the  
horizontal phase in 15¨ step.  
H.PHASE-FINE  
H.PHASE-FINE: Setting of 1-step fine  
adjustment in the above phase adjust-  
ment.  
28  
Setting of Menu Items  
# Camera ID setting menu  
°°CAM ID°°  
ID:AKHC900  
$ File managing and renewing menu  
H FILE MENU  
- File operation menu  
°
°
: blinking display.  
FILE  
SAVE FILE?  
SAVE  
:USER1  
:USER1  
:
1 The file selected by FILE is loaded.  
It can be selected from [PRESET/  
USER1 / USER2 /CURRENT].  
When desired to return to the previ-  
ous data after loading other file, se-  
lect CURRENT.”  
H FILE MENU  
°
°
FILE  
SAVE FILE?  
SAVE  
:USER1  
:USER1  
:
29  
Setting of Menu Items  
$ File managing and renewing menu  
H FILE MENU  
- File operation menu (continued)  
°
2 When saving the current data, two files  
(USER1 /USER2) can be saved.  
Select the file by SAVE FILE?”  
Select USER1and move the cursor  
to SAVE and press the MENU key,  
then the item menu is displayed.  
3 SAVE IN USER1. OK?  
FILE  
SAVE FILE?  
SAVE  
:USER1  
:USER1  
:
YESand NOare displayed.  
Move the cursor from NOto YES”  
and check that YESblinks.  
4 When the menu key is pressed, SAVE  
COMPLETEappears, then SAVEof  
the file is completed.  
FILE MENU  
FILE  
°
°
:USER1  
:USER1  
SAVE FIL?  
SAVE IN USER1.OK?  
YES  
NO  
FILE MENU  
°
°
FILE  
SAVE FIL?  
:USER1  
:USER1  
SAVE IN USER1.OK?  
SAVE COMPLETE  
30  

Quasar VML458 User Manual
Pioneer DEH P3700MP User Manual
Pioneer Car Video System AVH P5100DVD User Manual
Philips Digital Set Top Box DTR210 User Manual
Panasonic Car Stereo System CZ RWSU2U User Manual
Oster BCCG08 User Manual
Nikon Coolpix P300 User Manual
Lochinvar SYNC SB 1000 1500 User Manual
KitchenAid Blender 5KSB555 User Manual
JVC KW XR418 User Manual