PYLE Audio PLVW1445R User Manual

1
1. INSTALLATION GUIDE  
1. On a towel or soft cloth, gently place the monitor unit "facedown" on a  
stable work surface.  
2. Locate the pigtail with the DIN connector.  
3. Connect the DIN connector to the interface cable provided.  
4. Connect the RED wire to the positive (+) battery terminal.  
5. Connect the Black wire to a chassis electrical ground point.  
6. Connect the cable with YELLOW RCA jack to Video Input sources for  
your Video Program material.  
7. Connect the cable with RED and WHITE RCA jacks to Audio sources for  
your Audio Program material.  
8. Dome Light Circuit: (NOT SHOWN IN PICTURE) Connect the Black to  
Ground. Connect one red lead to the dome light circuit that is positive (+)  
when the door is open. Connect the other red lead to a constant positive (+).  
3
2. FUNCTION KEYS  
2.1 FRONT PANEL FUNCTIONS  
POWER: 1. Press the "POWER" button once, it will be "POWER ON."  
Press it again, it will be "POWER OFF."  
MENU: 1. Pop up the OSD menus. Press the "Menu" button again to  
enter the OSD menus. When in sub-menu, press.  
"EXIT" to go back to the main menu.  
UP/DN: 1. Press the "UP/DOWN" key to increase or decrease value  
2. Make item selection in OSD menus to increase or decrease  
parameters as well..  
4
2.2 FUNCTIONS OF REMOTE CONTROL  
Brightness:  
Contrast:  
adjust Brightness.  
adjust Contrast.  
Display adjust: Sharpness hue, saturation adjustment  
OSD display: OSD adjustment and display methods  
Input select:  
Audio:  
Recall:  
Exit:  
Switch between AV1 and AV2 Inputs.  
Mutes the Audio Signal  
Return to the main menu  
Exit’s the menu  
Press the "Menu key", to display a crosswise bar with digits. Use the  
INC/DEC keys to adjust the value, and then press the "Menu key" to confirm  
the adjustment. To have the crosswise bar and digits disappear; press "Exit" to  
leave the OSD function directly.  
5
3. TROUBLE SHOOTING  
3.1 NO POWER  
1. Make sure the power cable has been pluged in.  
2. Make sure the plug has 12V~14V, may use another electrical appliance  
to test it.  
3.2 NO FUNCTION OF REMOTE CONTROL  
1. Make sure the batteries are in good condition and installed properly.  
2. Make sure the remote control is aiming at the receiver, and there are no  
obstacles in between.  
3. Perhaps, it is too far away from the receiver. Normal distance is within 7  
meters.  
3.2 NO DISPLAY OR NOT CLEAR  
1. Check the video signal wires if they are connected properly.  
2. Check the antenna or adjust it.  
3. Make sure the TV/Video being in proper position.  
4. ACCESSORIES  
PS2/CAR CABLE  
INSTALLATION BRACKET  
USER MANUAL  
SCREW PACK  
REMOTE CONTROL  
6
5. SPECIFICATIONS  
ITEM  
LCD Panel  
DESCRIPTION  
14.1" TFT  
Active Area:  
Resolution:  
285.7 (W) x 214.3 (H) mm  
1024(H) x 3(RGB) x 768(V)  
262,144 colors  
0.279 (H) x 0.279 (V) mm  
CCFL Side-light type (four lamp)  
300 : 1  
Display Colors:  
Pixel Pitch (mm):  
Backlight Unit:  
Contrast Ratio:  
Brightness (cd/m2):  
Viewing Angle:  
300  
Horizontal:63O (typ.,Lift side), 63O (typ.,right  
side)  
Vertical: 45O (typ.,up side), 30O (typ.,down side)  
DC12V + 10% less than 2A  
Yes  
Power Supply:  
IR Transmitter:  
Power management:  
24W power consumption (typ.), less than 3W  
when in backlight sleep mode.  
Power on/off, OSD control  
1. Auto detection between NTSC/PAL  
2. Sceam is available  
User's Control:  
System:  
Dimensional Outline (mm): 338.0mm (W) x 340.2mm (H) x 52mm (D)  
Weight  
3.8 kg  
Safety Certifications:  
UL, FCC, CE, TUV  
Operation Temp.:0~50 degree C  
Storage Temp.: -20~60 degree C  
Humidity: 10~90%  
Environmental Condition:  
* Recommend for use with PYLE'S PLVWH1 wireless headphones.  
7

PYLE Audio PLAM3000 User Manual
Polaroid PDM 2727 User Manual
Pioneer AVH P6050DVD User Manual
Panasonic High Definition Video Camera HC V210M User Manual
Panasonic HDC HS100PC User Manual
MB QUART FX11000 User Manual
KitchenAid KFPW760QBW1 User Manual
Kenwood KDC MP445U User Manual
Kenwood KAC 6402 User Manual
JVC LYT1997 001B M User Manual