INSTALLATION
DASH BOARD
METAL MOUNTING STRAP
HEX NUT
PLCD25
SPRING WASHER
PLAIN WASHER
PLAIN WASHER
CONSOLE
TAPPING SCREW
SLIDE BRACKET HOUSING
INSTRUCTION MANUAL
HEX BOLT
OPEN
EJECT
Detachable Front Panel CAR Radio & CD Player
MIN
PLAY
PAUSE
TUNE
PWR
COMPACT
HOUR
DIGITAL AUDIO
CLK
BAND
MUTE
MO/INT
EQ
SEL
KEY PLATE
PLASTIC TRIM OUT
KEY PLATE
160WATTS
ANTI-THEFT DETACHABLE SYSTEM
AUTO-LOADING COMPACT DISC PLAYER
AM/FM STEREO WITH MANUAL TUNING RADIO
6. CD
( CD PLAY, PAUSE) BUTTON
button to switch to CD mode. At CD mode,
TROUBLE SHOOTING
At tuner mode, press
Before going through the check list, wiring connection, should any of the
problem persist after check list has been made, consult your nearest service
dealer.
press it to pause the CD program and press it again to resume CD
playback.
7. EJECT BUTTON
Press it to eject the disc from the slot.
Symptom
No power
Cause
Solution
8.9.10. SEL( AUDIO MODE SELECT)/VOLUME +/- BUTTON
Press SEL button to change the mode in sequence as follow:
The car ignition is not on.
If the power supply is properly
connected to the car accessory
switch the ignition key to " ACC "
VOL
BAS
TRE
BAL
FAD
The fuse is blown
Replace the fuse
Presence of CD disc inside
the player
Remove the disc in the player
then put a new upward
a. The volume level can be adjusted at any time by pressing the audio level
+ or - button as select mode has been initially defaulted at volume mode.
b. The volume level is also obtained by stepping through the SEL button until
the function VOL is displayed and then press + or - button to adjust the
sound level.
Disc cannot
be loaded or
ejected
Inserting the disc in upside
down
Insert the compact disc with
the label facing upward
Compact disc is extremely
dirty or defective
Clean the disc or try to play a
new one
c. Press and hold the + or - button to adjust the sound level.
Temperature inside the
car is too high
Cool off until the ambient
temperature returns to normal
BASS CONTROL
a. Press the SEL button to select the bass mode until BAS appears on the display.
b. Press + or - to adjust the bass effect.
Condensation
Leave the player off for an
hour or so, then try again
Volume is in minimum
Adjust volume to a desired level
No sound
TREBLE CONTROL
Wiring is not properly
connected
Check wiring connection
a. Press the SEL button to select the treble mode until TRE appears on the display.
b. Press + or - to adjust the treble effect.
The installation angle
is more than 30 degrees
Adjust the installation angle
to less than 30 degrees
Sound skips
BALANCE CONTROL
a. Press the SEL button to select the balance mode until BAL appears on the display.
b. Press the + button or - button to increase or decrease the sound level of
left or right speaker.
The disc is extremely
dirty or defective
Clean the compact disc/try to
play a new one
FADER CONTROL
The radio does
not work
a. Press the SEL button to select the fader mode until FAD appears on the display.
b. Press the + button or - button to increase or decrease the sound level of
front or rear speaker.
Insert the antenna cable firmly
The antenna cable is not
connected
the signals are too weak
11. EQ BUTTON
Press it to apply these function. Press it continually to switch between 3
preset equalizer curves: POP, CLAS, ROCK. The sound quality will be changed.
Press it again to cancel these function.
12. MUTE BUTTON
Press it to eliminate the sound temporarily, and press again to resume
normal play state.
13. BAND BUTTON
DISC PLAY:
Press it to select your desired radio band and the band which is selected will
be displayed on LCD.
Cleaning discs
Before playing, clean the disc with a clean, lint-free.
Flip the disc in the direction of the arrow.
14. MO/INT BUTTON
MO MODE: Press it to select mono or stereo mode.
INT MODE:
During CD mode, press " INTRO "button to hear the first 10 seconds
of each track on the disc. Press this button again to restore the
player to its normal play mode.
15. LOC/RPT BUTTON
LOCAL/DISTANCE MODE:
When in the radio mode, press them to select local or distance broadcast
station receive sensitivity. The word LOC will appear on LCD during local
state.
Attention: During AM mode, LOC is non-functional.
NOTE:
. Do not use so solvents such as benzine, thinners. Commercially available
cleaners or anti static spray damage the unit.
REPEAT MODE:
During CD mode. Press RPT button to repeat a single track.
Insert a disc with the label surface down. Doing so may damage the unit.
16. LUD/RDM BUTTON
Label
surface up
LUD MODE:
When reduce the volume to half level, press it to enhance the bass effect.
RDM MODE:
During CD mode, press " RDM " button and hold for 2 seconds,
it display " RDM " and Random function performs.
NOTE:
. Do not try to insert another disc when one has been already inserted.
17. TRACK UP/DOWN BUTTONS
Doing so may damage the unit.
.Handle the disc by its edge. And to keep the disc clean, do not touch
the surface.
A. During CD mode, press
button allow you to track forwards.
button allow you to track backwards.
Hold the
button allow you to skip forwards.
B. During CD mode, press
Hold the
button allow you to skip backwards.
IMPORTANT:
MEMORY WIRE ( FOR BACKUP) AND POWER WIRE CAN NOT BE SWITCHED
OFF AT THE SAME TIME, ONCE IT HAPPENS, ALL THE FUNCTION WILL BE
TOTALLY IN DISORDER (DISTORTED DISPLAY IS ALSO INDICATED ).
IF IT REALLY HAPPENS, PLEASE FOLLOW THE INSTRUCTIONS AS MENTIONED
BELOW:
5 MINUTES LATER, PLEASE SWITCH ON THE MEMORY WIRE FIRST (CAN NOT
PASS THROUGH IGNITION SWITCH) AND THEN SWITCH ON THE POWER. IT WILL
RETURN TO NORMAL FUNCTION SOON.
.Do not stick paper or tape on the disc.
.Do not expose the disc to direct sunlight or heat sources such as hot air
ducts. Or leave it in a car parked in direct sunlight where there can be a
considerable rise in temperature.
|