PAC C2R VW2 User Manual

C2R-VW2  
Radio Replacement Interface  
with Nav Outputs for select  
Volkswagen CANbus Vehicles With  
or Without Premium Audio Systems  
Class 2  
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0  
J1850  
Class 2  
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0  
Radio Connection Chart:  
(Read the Installation Notes before making  
connections to the provided radio harness)  
Navigation outputs and  
Amplifier Remote Input  
See Chart for wire color  
descriptions.  
Yellow  
Battery +12v  
Ground  
Black  
Blue  
Amp Turn On Input  
Front L + input  
Front L - input  
Front R + input  
Front R - input  
Rear L + input  
Rear L - input  
Rear R + input  
Rear R - input  
Radio Connections. See aside  
Chart for color description.  
White  
White / Black  
Grey  
Grey / Black  
Green  
Green / Black  
Purple  
Purple / Black  
Radio Specific Steering  
Wheel Control Interface  
(Sold Separately)  
Program SWC  
Interface for Version 2.  
CAN Interface Connection Chart:  
Red  
Acc. Output (1 amp)  
P.B. Output (-)  
Red / White  
Purple / White  
audio.com  
VSS Output (Pulse)  
Orange / White Illum. Output (+)  
1. Vehicles with or without a factory amplifier: Connect the aftermarket radio’s  
front and rear speaker wires to the 16 pin plug.  
2. The accessory output wire is located on the 11 pin CAN INTERFACE harness  
- connect this wire to the radio’s accessory wire. The accessory wire supplies  
Green  
Reverse Output (+)  
SWC Output  
White / Green  
+12v, 1 amp max when key is in the  
accessory or ignition position (see fig. 1: If more current is needed).  
Fig. 1  
(using a SPDT relay)  
High Current 12v  
(Fused)  
3. 11 pin plug (to CAN INTERFACE):  
1. White/Green - SWC output.  
85  
86  
87  
12v Acc.  
From  
Interface  
Ground  
2. Green - Connect this wire to the radio’s reverse input wire only.  
3. Orange/White - Connect this wire to the radio’s Illumination input wire only.  
4. Violet/White - Connect this wire to the radio’s VSS input wire only.  
5. Red/White - Connect this wire to the radio’s parking brake input wire only.  
Please Note: The parking brake wire will output a neg (-) trigger at all  
times until the vehicle is moving at a speed of approximately 3 mph or  
faster.  
87a  
30  
Diode 1N4005  
or equivelant  
New High  
Current Output  
Note: Do not connect these wires to any circuit other than the aftermarket radio’s wire har
4. 11 pin plug (to SWC INTERFACE):  
This is a quick connection to a radio specific SWC interface. No additional connections are necessary other than radio  
control connections. Plug the radio specific SWC interface in to this connector and program the radio specific SWC  
interface for version 2. Do not cut the loops. Refer to the SWC interface instruction manual for the radio specific control  
function programming order.  
5. Refer to the aftermarket radio’s instruction manual for testing VSS, Reverse, Parking Brake and Illumination outputs.  
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the C2R-VW2 be held liable for consequential damages sustained in  
connection with the C2R-VW2. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume  
obligation or liability in relation to the C2R-VW2 other than its replacement.  
Pacific Accessory Corporation - Santa Ana, CA 92705  
01-04-10  

Planar Systems Car Video System pl191m User Manual
Philips VKR 6880 User Manual
Philips VKR 6843 User Manual
Panasonic AG HPX172EN User Manual
Oster Blender 14 CUP FOOD PROCESSOR WITH 5 CUP WORK BOWL User Manual
Orion Car Audio C463 User Manual
Metra Electronics 95 7331 User Manual
Mercedes Benz Car Amplifier Audio 50 User Manual
Linear CCM 1 User Manual
JVC LYT1528 001B User Manual