Nokia BH 213 User Manual

Nokia Bluetooth Headset BH-213

Issue 1

Export controls

This device may contain commodities,

laws and regulations from the US and

other countries. Diversion contrary to

technology or software subject to export law is prohibited.

Introduction

With the Nokia Bluetooth Headset in line of sight, but they should be

BH-213, you can make and receive within 10 metres (33 feet) of each

calls while on the move.

other. Connections may be subject

to interference from obstructions,

such as walls, or other electronic

devices.

Read this user guide carefully

before using the headset. Also,

read the user guide for your phone.

It provides important safety and

maintenance information.

The headset complies with the

Bluetooth Specification 2.0 + EDR

that supports the Headset Profile

1.1 and Hands-Free Profile 1.5.

Check with the manufacturers of

other devices to determine their

compatibility with this device.

This product may contain small

parts. Keep them out of the reach

of small children.

Bluetooth wireless

technology

Bluetooth wireless technology

allows you to connect compatible

devices without cables. The phone

and the headset do not need to be

Get started

following chargers: AC-3, AC-4, AC-

5, and DC-4.

The headset contains the

following parts shown on the title

page: indicator light (1),

multifunction key (2), charger

connector (3), earloop (4), earpiece

(5), volume key (6), and

Warning: Use only

chargers approved by

Nokia for use with this

particular enhancement. The use of

any other types may invalidate any

approval or warranty, and may be

dangerous.

microphone (7).

Before using the headset, you

must charge the battery and pair

the headset with a compatible

phone.

When you disconnect the power cord

of any enhancement, grasp and pull

the plug, not the cord.

Parts of the device are magnetic.

Metallic materials may be attracted

to the device. Do not place credit

cards or other magnetic storage

media near the device, because

information stored on them may be

erased.

Charge the battery

Before charging the battery,

carefully read “Battery

information”.

1. Connect the charger to a wall

outlet.

Chargers

This device is intended for use when

supplied with power from the

2. Connect the charger cable to

the charger connector. The red

indicator light is on during

charging. Charging the battery To switch off, press and hold the

fully may take up to 2 hours.

multifunction key for about 5

seconds. The headset beeps, and

the red indicator light is briefly

displayed.

3. When the battery is fully

charged, the green indicator

light is displayed. Disconnect

the charger from the headset,

then the wall outlet.

Pair the headset

1. Ensure that your phone is on

and the headset is off.

The fully charged battery has

power for up to 10 hours of talk

time or up to 400 hours of standby

time.

2. Press and hold the

multifunction key (for about 5

seconds) until the green

indicator light starts to flash

quickly.

When the battery is discharged,

the headset beeps every minute

and the red indicator light flashes

quickly.

3. Activate the Bluetooth feature

on the phone, and set it to

Switch on or off

search for Bluetooth devices.

To switch on, press and hold the

multifunction key for about 2

seconds. The headset beeps, and

the green indicator light is

displayed. The headset tries to

connect to a paired phone.

4. Select the headset from the list

of found devices.

5. Enter the passcode 0000 to

pair and connect the headset to

your phone. In some phones,

you may need to make the

connection separately after

pairing.

When the headset is connected to

your phone and is ready for use,

the green indicator light flashes

slowly.

Basic use

Place the headset on the ear Calls

To use the headset with the

earloop, attach the earloop to it

(8). To detach the earloop, gently

pull it from the headset (9).

To make a call, use your phone in

the normal way when the headset

is connected to it.

To redial the number you last

Slide the earloop behind your ear called (if your phone supports this

(10), and point the headset toward feature with the headset), when

your mouth. Carefully bend the

earloop around your ear for the

best fit (11).

no call is in progress, press the

multifunction key twice.

To activate voice dialling (if your

phone supports this feature with

To change the earplug, pull the

current earplug from the earpiece, the headset), when no call is in

and push the new earplug over the progress, press and hold the

earpiece in the same position.

multifunction key for about 2

seconds. Proceed as described in

the phone user guide.

To answer or end a call, press the

multifunction key for about 2

multifunction key. To reject a call, seconds (the headset switches on).

press this key twice.

Clear settings or reset

To adjust the volume during a call,

To delete the pairings from the

slide the volume key up or down.

headset or reset the headset,

switch off the headset, and press

To mute or unmute the

microphone during a call, briefly

and hold the multifunction key for

press the middle of the volume

over 8 seconds.

key.

Troubleshooting

To switch a call from the headset

to a compatible phone, press and

hold the multifunction key for

about 5 seconds (the headset

switches off). To switch the call

back to the headset, press the

If you cannot connect the headset

to your compatible phone, check

that the headset is charged,

switched on, and paired with the

phone.

Battery information

This device has an internal,

times, but it will eventually wear out.

nonremovable, rechargeable battery. Recharge your battery only with

Do not attempt to remove the battery Nokia approved chargers designated

from the device as you may damage

the device. The battery can be

for this device. Use of an unapproved

charger may present a risk of fire,

charged and discharged hundreds of explosion, leakage, or other hazard.

If a battery is being used for the first limited in temperatures well below

time or if the battery has not been

used for a prolonged period, it may be

necessary to connect the charger,

then disconnect and reconnect it to

begin charging the battery. If the

battery is completely discharged, it

may take several minutes before the

charging indicator light is displayed.

freezing.

Do not dispose of batteries in a fire as

they may explode. Batteries may also

explode if damaged.

Never use any charger that is

damaged.

Important: Battery talk

and standby times are

estimates only and

Unplug the charger from the

electrical plug and the device when

not in use. Do not leave a fully

charged battery connected to a

charger, since overcharging may

shorten its lifetime. If left unused, a

fully charged battery will lose its

charge over time.

depend on network conditions,

features used, battery age and

condition, temperatures to which

battery is exposed, and many other

factors. The amount of time a device

is used for calls will affect its standby

time. Likewise, the amount of time

that the device is turned on and in

the standby mode will affect its talk

time.

Always try to keep the battery

between 15°C and 25°C (59°F and

77°F). Extreme temperatures reduce

the capacity and lifetime of the

battery. A device with a hot or cold

battery may not work temporarily.

Battery performance is particularly

Care and maintenance

Your device is a product of superior

design and craftsmanship and should

be treated with care. The following

suggestions will help you protect

your warranty coverage.

its normal temperature, moisture

can form inside the device and

damage electronic circuit boards.

•

Do not attempt to open the

device.

•

Keep the device dry. Precipitation,

humidity, and all types of liquids

or moisture can contain minerals

that will corrode electronic

Do not drop, knock, or shake the

device. Rough handling can break

internal circuit boards and fine

mechanics.

circuits. If your device does get

wet, allow it to dry completely.

•

Do not use harsh chemicals,

cleaning solvents, or strong

detergents to clean the device.

•

Do not use or store the device in

dusty, dirty areas. Its moving parts

and electronic components can

be damaged.

Do not paint the device. Paint can

clog the moving parts and prevent

proper operation.

Do not store the device in hot

areas. High temperatures can

shorten the life of electronic

devices, damage batteries, and

warp or melt certain plastics.

These suggestions apply equally to

your device, charger, or any

enhancement. If any device is not

working properly, take it to the

nearest authorised service facility for

service.

•

Do not store the device in cold

areas. When the device returns to

RCA EZ209HD User Manual
Pioneer DVD Receiver AVH X5500BHS User Manual
Pioneer DEH P5800MP User Manual
Oster Blender OSTER VERSA PERFORMANCE BLENDER User Manual
Orion Car Audio XTR Power Amplifier XTR5001 User Manual
Orion Car Audio Coaxial Speaker XTR652 User Manual
Nikon Coolpix COOLPIXS9300BLK User Manual
Mitsubishi Electronics Mitsubishi Digital Electronics Car Amplifier MR J3 B User Manual
Lightning Audio Bolt B23501 User Manual
Kenwood KFC W210 User Manual