DIGITAL CAMERA
User’s Manual
En
Trademark Information
• Microsoft, Windows and Windows Vista are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other
countries.
• Macintosh, Mac OS, and QuickTime are trademarks of Apple Inc.
• Adobe and Acrobat are registered trademarks of Adobe Systems Inc.
• SDXC, SDHC, and SD Logos are trademarks of SD-3C, LLC.
• PictBridge is a trademark.
• HDMI,
logo, and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
• ACCESS and NetFront are registered trademarks or trademarks of ACCESS Co.,
LTD in Japan, the United States and/or other countries.
• All other trade names mentioned in this manual or the other documentation
provided with your Nikon product are trademarks or registered trademarks of
their respective holders.
AVC Patent Portfolio License
This product is licensed under the AVC Patent Portfolio License for the personal
and non-commercial use of a consumer to (i) encode video in compliance with
the AVC standard (“AVC video”) and/or (ii) decode AVC video that was encoded by
a consumer engaged in a personal and non-commercial activity and/or was
obtained from a video provider licensed to provide AVC video. No license is
granted or shall be implied for any other use. Additional information may be
obtained from MPEG LA, L.L.C.
See http://www.mpegla.com.
For Your Safety
To prevent damage to your Nikon product or injury to yourself or to others, read
the following safety precautions in their entirety before using this equipment.
Keep these safety instructions where all those who use the product will read them.
The consequences that could result from failure to observe the precautions listed
in this section are indicated by the following symbol:
This icon marks warnings, information that should be read before using this Nikon
product, to prevent possible injury.
WARNINGS
Turn off in the event of
malfunction
Should you notice smoke or an
Do not use the camera or AC
adapter in the presence of
flammable gas
Do not use electronic equipment in
the presence of flammable gas, as this
could result in explosion or fire.
unusual smell coming from the
camera or AC adapter, unplug the AC
adapter and remove the battery
immediately, taking care to avoid
burns. Continued operation could
result in injury. After removing or
disconnecting the power source, take
the equipment to a Nikon-authorized
service representative for inspection.
Handle the camera strap with
care
Never place the strap around the neck
of an infant or child.
Keep out of reach of children
Particular care should be taken to
prevent infants from putting the
battery or other small parts into their
mouths.
Do not disassemble
Touching the internal parts of the
camera or AC adapter could result in
injury. Repairs should be performed
only by qualified technicians. Should
the camera or AC adapter break open
as the result of a fall or other accident,
take the product to a Nikon-authorized
service representative for inspection,
after unplugging the product and/or
removing the battery.
ii
For Your Safety
Observe caution when
handling the battery
• Discontinue use immediately should
you notice any change in the
battery, such as discoloration or
deformation.
• If liquid from the damaged battery
comes in contact with clothing or
skin, rinse immediately with plenty
of water.
The battery may leak or explode if
improperly handled. Observe the
following precautions when handling
the battery for use in this product:
• Before replacing the battery, turn
the product off. If you are using the
AC adapter (available separately), be
sure to unplug the AC adapter from
an electrical outlet.
• Use only a Rechargeable Li-ion
Battery EN-EL10 (supplied).
Charge the battery inserted into the
camera by connecting the Charging
AC Adapter EH-68P/EH-68P (AR)
(supplied).
• When inserting the battery, do not
attempt to insert it upside down or
backwards.
• Do not short or disassemble the
battery or attempt to remove or
break the battery insulation or
casing.
Observe the following
precautions when handling
the Charging AC Adapter
• Keep dry. Failure to observe this
precaution could result in fire or
electric shock.
• Dust on or near the metal parts of
the plug should be removed with a
dry cloth. Continued use could
result in fire.
• Do not handle the cable or go near
the Charging AC Adapter during
lightning storms. Failure to observe
this precaution could result in
electric shock.
• Do not damage, modify, forcibly tug
or bend the cable, place it under
heavy objects, or expose it to heat or
flames. Should the insulation be
damaged and the wires become
exposed, take it to a Nikon-
authorized service representative for
inspection. Failure to observe these
precautions could result in fire or
electric shock.
• Do not expose the battery to flame
or to excessive heat.
• Do not immerse in or expose to
water.
• Return the battery to the battery
case for transportation. Do not
transport or store with metal objects
such as necklaces or hairpins.
• The battery is prone to leakage
when fully discharged. To avoid
damage to the product, be sure to
remove the battery when no charge
remains.
iii
For Your Safety
• Do not handle the plug or Charging
AC Adapter with wet hands. Failure
to observe this precaution could
result in electric shock.
• Do not use with travel converters or
adapters designed to convert from
one voltage to another or with DC-
to-AC inverters. Failure to observe
this precaution could damage the
product or cause overheating or fire.
Do not operate the flash with
the flash window touching a
person or object
Failure to observe this precaution
could result in burns or fire.
Do not apply pressure to the
monitor
Should the monitor break, care should
be taken to avoid injury caused by
broken glass.
Use appropriate cables
When connecting cables to the input
and output jacks, use only the cables
provided or sold by Nikon for the
purpose, to maintain compliance with
product regulations.
Turn the power off when
using inside an airplane or the
hospital
Turn the power off while inside the
airplane during take off or landing.
Follow the instructions of the hospital
when using while in a hospital. The
electromagnetic waves given out by
this camera may disrupt the electronic
systems of the airplane or the
Handle moving parts with
care
Be careful that your fingers or other
objects are not pinched by the slide
cover or other moving parts.
instruments of the hospital.
CD-ROMs
The CD-ROMs supplied with this
device should not be played back on
audio CD equipment. Playing CD-
ROMs on an audio CD player could
cause hearing loss or damage the
equipment.
Observe caution when using
the flash
Using the flash close to your subject’s
eyes could cause temporary visual
impairment. Particular care should be
observed if photographing infants,
when the flash should be no less than
one meter (3 ft. 4 in.) from the subject.
iv
Notices
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an
Notices for Customers in the U.S.A.
IMPORTANT SAFETYINSTRUCTIONS–
SAVE THESE INSTRUCTIONS.
DANGER - TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK,
CAREFULLY FOLLOW THESE
INSTRUCTIONS
experienced radio/television
technician for help.
For connection to a supply not in the
U.S.A., use an attachment plug adapter
of the proper configuration for the
power outlet if needed.
The power supply unit is intended to
be correctly orientated in a vertical or
floor mount position.
CAUTIONS
Modifications
The FCC requires the user to be
notified that any changes or
modifications made to this device that
are not expressly approved by Nikon
Corporation may void the user’s
authority to operate the equipment.
Federal Communications
Commission (FCC) Radio
Frequency Interference Statement
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC rules. These limits are
designed to provide reasonable
protection against harmful
interference in a residential installation.
This equipment generates, uses, and
can radiate radio frequency energy
and, if not installed and used in
Interface Cables
Use the interface cables sold or
provided by Nikon for your equipment.
Using other interface cables may
exceed the limits of Class B Part 15 of
the FCC rules.
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
Notice for customers in the State of
California
WARNING
Handling the cord on this product will
expose you to lead, a chemical known
to the State of California to cause birth
defects or other reproductive harm.
Wash hands after handling.
Nikon Inc.,
1300 Walt Whitman Road
Melville, New York 11747-3064
USA
• Reorient or relocate the receiving
antenna.
Tel: 631-547-4200
v
Notices
appropriate collection point. Do not
dispose of as household waste.
• For more information, contact the
retailer or the local authorities in
charge of waste management.
Notice for customers in Canada
CAUTION
This Class B digital apparatus complies
with Canadian ICES-003.
ATTENTION
Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du
Canada.
Notices for customers in Europe
CAUTION
RISK OF EXPLOSION IF BATTERY IS
REPLACED BY AN INCORRECT
TYPE.
DISPOSE OF USED BATTERIES
ACCORDING TO THE
INSTRUCTIONS.
This symbol indicates that
this product is to be
collected separately.
The following apply only to
users in European countries:
• This product is designated for
separate collection at an
appropriate collection point. Do not
dispose of as household waste.
• For more information, contact the
retailer or the local authorities in
charge of waste management.
This symbol on the battery
indicates that the battery is
to be collected separately.
The following apply only to
users in European countries:
• All batteries, whether marked with
this symbol or not, are designated
for separate collection at an
vi
Table of Contents
For Your Safety......................................................................................................................................ii
WARNINGS..................................................................................................................................................................ii
Attaching the Camera Strap............................................................................................................................4
Shutter-Release Button.......................................................................................................................................5
Dragging......................................................................................................................................................................6
First Steps............................................................................................................................................. 14
Removing the Battery.......................................................................................................................................15
Basic Photography and Playback: G (Easy Auto) Mode..................................................... 24
Step 1 Turn the Camera On and Select G Easy Auto Mode................................................24
Indicators Displayed in G (Easy Auto) Mode....................................................................................25
Step 3 Focus and Shoot.....................................................................................................................28
Playing Back Pictures (Playback Mode)..................................................................................................30
m Using the Flash................................................................................................................................................33
n Taking Pictures with the Self-timer ...................................................................................................36
vii
Table of Contents
A Image Mode (Image Quality/Image Size) .....................................................................................38
q Tapping the Monitor to Release the Shutter (Touch Shutter)..........................................41
r Tapping the Monitor to Focus (Touch AF/AE) ..........................................................................44
o Changing Brightness Using Exposure Compensation..........................................................47
Selecting a Shooting Mode..............................................................................................................48
G (Easy Auto) Mode...........................................................................................................................49
Shooting in A (Auto) Mode ............................................................................................................51
Adjusting the A (Auto) Mode Setting.........................................................................................53
p Macro Mode Setting...................................................................................................................................54
s Subject Tracking (Focusing on a Moving Subject).................................................................55
E ISO Sensitivity.................................................................................................................................................57
V Continuous ......................................................................................................................................................58
w White Balance (Adjusting Hue)...........................................................................................................59
Shooting Suited to Scenes (Scene Mode)...................................................................................61
Changing the Smart Portrait Mode Settings......................................................................................74
Camera Settings That cannot be Applied Simultaneously...................................................76
Taking a Closer Look: Playback Zoom..........................................................................................81
Selecting Playback Mode..................................................................................................................83
Operations in Favorite Pictures Mode....................................................................................................88
Operations in Auto Sort Mode....................................................................................................................93
Operations in List by Date Mode...............................................................................................................95
Playing Back Pictures by Rating..................................................................................................................97
b Enjoying Slide Shows...................................................................................................................98
viii
Table of Contents
d Protecting Important Pictures (Protect)............................................................................ 100
Protecting One Picture..................................................................................................................................100
Protecting Multiple Pictures ......................................................................................................................101
Removing Protection from Pictures......................................................................................................101
a Creating a DPOF Print Order: Print Set................................................................................ 102
Creating a Print Order for One Picture ................................................................................................102
Creating a Print Order for Multiple Pictures.....................................................................................104
Canceling Print Order.....................................................................................................................................105
f Rotate Image ................................................................................................................................ 106
E Voice Memo: Recording and Playback ................................................................................. 107
Recording Voice Memos..............................................................................................................................107
Playing Voice Memos.....................................................................................................................................108
Deleting Voice Memos..................................................................................................................................108
Editing Functions.............................................................................................................................. 109
U Paint...................................................................................................................................................................111
k Quick Retouch: Enhancing Contrast and Saturation..........................................................114
I D-Lighting: Enhancing Brightness and Contrast...................................................................115
P Stretch: Stretching Pictures.................................................................................................................116
O Perspective Control: Adjust a Sense of Perspective.............................................................117
i Filter Effects (digital filter)......................................................................................................................118
j Glamour Retouch.......................................................................................................................................120
g Small Picture: Making Smaller Pictures........................................................................................122
o Crop: Creating a Cropped Copy........................................................................................................123
Movie Recording and Playback..................................................................................................124
Movie Recording Settings...........................................................................................................................126
A Movie Options.............................................................................................................................................127
Movie Playback.................................................................................................................................. 128
Connecting to Televisions, Computers and Printers..........................................................129
Connecting to a TV........................................................................................................................... 129
Before Connecting the Camera...............................................................................................................132
Transferring Images from a Camera to a Computer...................................................................133
Charging While Connecting to a Computer ...................................................................................137
Connecting the Camera to a Printer.....................................................................................................139
Printing Pictures One at a Time ...............................................................................................................141
Printing Multiple Pictures............................................................................................................................142
ix
Table of Contents
Operating the Setup Menu ........................................................................................................................146
c Welcome Screen........................................................................................................................................147
d Date....................................................................................................................................................................148
e Monitor Settings .......................................................................................................................................151
f Date Imprint (Imprinting Date and Time)..................................................................................152
g Vibration Reduction................................................................................................................................153
h AF Assist.........................................................................................................................................................154
u Digital Zoom ...............................................................................................................................................154
i Sound Settings ...........................................................................................................................................155
k Auto Off ..........................................................................................................................................................155
l/m Format Memory/Format Card...................................................................................................156
n Language........................................................................................................................................................157
H TV Settings.....................................................................................................................................................158
V Charge by Computer ..............................................................................................................................159
d Blink Warning .............................................................................................................................................159
p Reset All...........................................................................................................................................................161
r Firmware Version ....................................................................................................................................165
Cleaning .................................................................................................................................................................168
Storage....................................................................................................................................................................168
Approved Memory Cards............................................................................................................................170
Error Messages................................................................................................................................... 172
Supported Standards.....................................................................................................................................187
Index...................................................................................................................................................... 188
x
Introduction
About This Manual
Thank you for your purchase of a Nikon COOLPIX S80 digital camera. This manual
was written to help you enjoy taking pictures with your Nikon digital camera. Read
this manual thoroughly before use, and keep it where all those who use the
product will read it.
Symbols and Conventions
To make it easier to find the information you need, the following symbols and
conventions are used:
This icon marks cautions,
This icon marks tips, additional
information that should be read
information that may be helpful
B
C
D
before use, to prevent damage to
the camera.
when using the camera.
This icon marks notes, information
that should be read before using
the camera.
This icon indicates that more
information is available elsewhere
in this manual.
A
Notations
• Secure Digital (SD) memory card, SDHC memory card, and SDXC memory card
are referred to as “memory card.”
• The setting at the time of purchase is referred to as the “default setting.”
• The names of menu items displayed in the camera monitor, and the names of
buttons or messages displayed on a computer monitor appear in bold.
Screen Samples
In this manual, images are sometimes omitted from monitor display samples so
that monitor indicators can be more clearly shown.
Illustrations and Screen Display
Illustrations and text displays shown in this manual may differ from actual display.
C Internal Memory and Memory Cards
Pictures taken with this camera can be stored in the camera’s internal memory or on removable
memory cards. If a memory card is inserted, all new pictures will be stored on the memory card and
delete, playback and format operations will apply only to the pictures on the memory card. The
memory card must be removed before the internal memory can be formatted or accessed for
picture storage, deletion, or viewing.
1
Information and Precautions
Life-Long Learning
As part of Nikon’s “Life-Long Learning” commitment to ongoing product support and education,
continually updated information is available online at the following sites:
• For users in the U.S.A.: http://www.nikonusa.com/
• For users in Europe and Africa: http://www.europe-nikon.com/support/
• For users in Asia, Oceania, and the Middle East: http://www.nikon-asia.com/
Visit these sites to keep up-to-date with the latest product information, tips, answers to frequently
asked questions (FAQs), and general advice on digital imaging and photography. Additional
information may be available from the Nikon representative in your area. Visit the site below for
contact information.
URL below for contact information:
http://imaging.nikon.com/
Use Only Nikon Brand Electronic Accessories
Nikon COOLPIX cameras are designed to the highest standards and include complex electronic
circuitry. Only Nikon brand electronic accessories (including battery charger, batteries, Charging AC
Adapter and AC adapters) certified by Nikon specifically for use with this Nikon digital camera are
engineered and proven to operate within the operational and safety requirements of this electronic
circuitry.
THE USE OF NON-NIKON ELECTRONIC ACCESSORIES COULD DAMAGE THE CAMERA AND MAY
VOID YOUR NIKON WARRANTY.
The use of third-party rechargeable Li-ion batteries not bearing the
Nikon holographic seal could interfere with normal operation of the
camera or result in the batteries overheating, igniting, rupturing, or
Holographic seal:
leaking.
Identifies this device as an
For more information about Nikon brand accessories, contact a local
authentic Nikon product.
authorized Nikon dealer.
Before Taking Important Pictures
Before taking pictures on important occasions (such as at weddings or before taking the camera on
a trip), take a test shot to ensure that the camera is functioning normally. Nikon will not be held liable
for damages or lost profits that may result from product malfunction.
About the Manuals
• No part of the manuals included with this product may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language in any form, by any means, without
Nikon’s prior written permission.
• Nikon reserves the right to change the specifications of the hardware and software described in
these manuals at any time and without prior notice.
• Nikon will not be held liable for any damages resulting from the use of this product.
• While every effort was made to ensure that the information in these manuals is accurate and
complete, we would appreciate it were you to bring any errors or omissions to the attention of the
Nikon representative in your area (address provided separately).
2
Information and Precautions
Notice Concerning Prohibition of Copying or Reproduction
Note that simply being in possession of material that was digitally copied or reproduced by means
of a scanner, digital camera or other device may be punishable by law.
• Items prohibited by law from being copied or reproduced
Do not copy or reproduce paper money, coins, securities, government bonds or local government
bonds, even if such copies or reproductions are stamped “Sample.” The copying or reproduction
of paper money, coins, or securities which are circulated in a foreign country is prohibited. Unless
the prior permission of the government was obtained, the copying or reproduction of unused
postage stamps or post cards issued by the government is prohibited. The copying or
reproduction of stamps issued by the government and of certified documents stipulated by law is
prohibited.
• Cautions on certain copies and reproductions
The government has issued cautions on copies or reproductions of securities issued by private
companies (shares, bills, checks, gift certificates, etc.), commuter passes or coupon tickets, except
when a minimum of necessary copies are to be provided for business use by a company. Also, do
not copy or reproduce passports issued by the government, licenses issued by public agencies
and private groups, ID cards and tickets, such as passes and meal coupons.
• Comply with copyright notices
The copying or reproduction of copyrighted creative works such as books, music, paintings,
woodcut prints, maps, drawings, movies and photographs is governed by national and
international copyright laws. Do not use this product for the purpose of making illegal copies or to
infringe copyright laws.
Disposing of Data Storage Devices
Please note that deleting images or formatting data storage devices such as memory cards or built-
in camera memory does not completely erase the original image data. Deleted files can sometimes
be recovered from discarded storage devices using commercially available software, potentially
resulting in the malicious use of personal image data. Ensuring the privacy of such data is the user’s
responsibility.
Before discarding a data storage device or transferring ownership to another person, erase all data
using commercial deletion software, or format the device and then completely refill it with images
containing no private information (for example, pictures of empty sky). Be sure to also replace any
to property when physically destroying data storage devices.
3
Parts of the Camera
The Camera Body
11 10 9
Lens cover closed
1
2
3
4
5
6
12
7
8
1
2
3
7
8
9
Memory card slot..........................................22
Battery-chamber/
4
10
5
6
Attaching the Camera Strap
4
Parts of the Camera
1
2
3
4
5
Under the connector cover
6
7
OLED monitor (monitor)*/
touch panel.........................................................6
Power connector cover
(for connection with optional AC
1
5
2
3
4
Tripod socket
USB/audio/video output
6
7
* Referred to simply as the “monitor” in this manual.
Shutter-Release Button
The camera features a two-stage shutter-release button. To set focus and
exposure, press the shutter-release button halfway, stopping when you feel
resistance. Focus and exposure lock while the shutter-release button is held in this
position. To release the shutter and take a picture, press the shutter-release button
the rest of the way down. Do not use force when pressing the shutter-release
button, as this may result in camera shake and blurred pictures.
Press the shutter-
release button
Press the shutter-
release button the
halfway to set focus rest of the way down
and exposure. to take a picture.
5
Operating the Touch Panel
The monitor on the COOLPIX S80 is a touch panel display operated by touch. Use
the method described below.
Tapping
Tap the touch panel.
Use this operation to:
Select icons or other controls
Display the setting controls during shooting or
Dragging
Drag your finger across the touch panel and
remove it from the touch panel.
Use this operation to:
Scroll through pictures in full-frame playback mode
When the camera is in full-fame playback mode,
drag two fingers across the touch panel to scroll
ahead ten frames quickly.
Place two fingers on the touch panel about 1.5 cm
(0.6 in.) apart, slide them about 2 cm (0.8 in.) to left or
right. Note that the desired results may not be
achieved if your fingers are placed side by side.
Tap the touch panel to stop at the current frame.
6
Operating the Touch Panel
Dragging and Dropping
Place your finger on the touch panel,
drag it to the desired location ( ), and
1
remove it from the touch panel ( ).
2
Use this operation to:
Spreading/pinching
Spread two fingers apart/pinch two
fingers together
Use this operation to:
mode
Switch to thumbnail playback mode from full-
B Notes on the Touch Panel
• This camera utilizes a static touch panel. Therefore, it may not respond when touched with
fingernails or gloved fingers.
• Do not press on the touch panel with pointed objects.
• Do not apply unnecessary pressure to the touch panel.
• The touch panel may not respond to touch if a commercially available protecting film is applied.
B Notes on Touch Panel Operations
• The camera may not respond if your finger is left in one place too long.
• The camera may not respond if the followings are made.
- Bounce your finger off the display
- Drag your finger over too short a distance
- Stroke the display too lightly
- Move your finger too quickly
- Change the distance between your fingers while you drag two fingers or drag them too far
- Both fingers are not moved simultaneously when spreading or pinching
7
Main Display of the Monitor/Touch Panel and Basic Operations
Shooting (Information Indicators)
The information displayed on the monitor varies with the camera settings or
status.
18 17
16 15 14 13 12
1
2
11
10
9
8
3
36
T
a
50
m00s
m00s
1
1
W
4
b
36
5
1/250 F3.6
6
7
1
Focus area (center)
2
3
4
5
6
7
q O
13
O
15
a
Number of exposures remaining
8
b Movie recording time remaining
........................................................................ 127
9
* Indicator is displayed when there are 50 or fewer exposures remaining.
C Auto Monitor Boost
The camera automatically increases monitor brightness outdoors and under extremely bright
8
Main Display of the Monitor/Touch Panel and Basic Operations
Shooting (Operation Controls)
Tap the following controls to change settings.
• Tap the tab to display the setting controls and shooting settings can be
• The controls available and the setting status displayed vary depending upon
the shooting mode and the current camera settings.
8
1
2
3
4
T
7
6
OFF
AUTO
W
AUTO
0.0
5
1
2
3
4
5
Wide zoom .......................................................27
Tele zoom..........................................................27
Scene effect adjustment slider ............63
6
7
8
* Indicators displayed vary with current shooting mode.
C Monitor Display in Portrait (“Tall”) Orientation
When the camera is held in portrait (“tall”) orientation, the controls and indicators are also displayed
in portrait (“tall”) orientation. Controls and indicators may not be appropriately rotated when the
camera is pointing up or down.
T
W
AUTO
T
OFF
AUTO
0.0
W
AUTO
0.0
OFF
AUTO
9
Main Display of the Monitor/Touch Panel and Basic Operations
Playback (Information Display)
The following monitor display shows information for the picture currently
displayed and camera status.
• The information displayed on the monitor varies with the camera settings or
status.
• The indicators below are displayed when the camera is turned on or is in
1
2
3
4
5 6
:
15 30
15 11 2010
9999. JPG
7
8
9
4/
4
a
9999/9999
1
1
m00s
m00s
b
4
4
11
10
8
1
2
i
1
3
1
4
5
6
Print-order icon .......................................... 102
Protect icon................................................... 100
Album icon in favorite
a
a
Current frame number/
9
2
7
2
1
2
Indicators displayed vary depending on the setting for shooting.
The icon for the selected album or category in auto sort mode currently selected in
playback mode is displayed.
10
Main Display of the Monitor/Touch Panel and Basic Operations
Playback (Operation Controls)
Tap the following controls to change settings.
be available.
• The controls available displayed vary depending upon the displayed picture
and the current camera settings.
5
1
2
3
4
1
Switch to shooting mode
3
4
5
1
2
2
1
2
Indicators displayed vary with the shooting mode.
Indicators displayed vary with current playback mode.
C Picture Display
When the camera is rotated, the picture and controls displayed are also rotated as indicated below.
Pictures and controls may not be appropriately rotated when the camera is pointing up or down.
11
Main Display of the Monitor/Touch Panel and Basic Operations
Opening the Tabs
When in shooting or playback mode, use the setting controls to make shooting
and playback settings. Display the controls by tapping the tab at the bottom, left
or right side of the monitor.
• Tap the icon of the desired item to display the setting screen for that item.
• Tap z (setup) in the setting controls to make the basic camera settings.
• When H or J is displayed on the setting screen, tap H to exit the setting
screen and tap J to return to the previous screen.
• Tap the tab again to hide the setting controls.
Tap the tab to display
the icons of settings
that can be changed in
the current mode.
T
W
36
To hide setting
controls, tap the tab
again.
Tap z to display the
setup menu.
T
Tap an icon to display
the setting screen of
that item.
W
OFF
0.0
Tap an icon to apply
the setting of that
item.
Return to the previous
screen.
Image mode
3968×2232
12
Main Display of the Monitor/Touch Panel and Basic Operations
Shooting
Shooting settings can be made.
• Each icon also indicates the current setting.
X
p
Flash mode.............................................33
1
n
A
Self-timer..................................................36
1
T
Touch shooting
W
OFF
2
3
V
Continuous.............................................58
2
3
o
Exposure compensation................47
T
OFF
AUTO
z
W
AUTO
0.0
Playback
Pictures can be edited and deleted, and playback settings can be made.
• The available setting items vary depending on the type of picture or playback
mode.
1
2
3
Rating...................................................................97
Add pictures to albums
(except in favorite pictures mode) ....84
Remove pictures from albums (in
5
4
3
2
1
0
h
1
c
b
Delete ........................................................31
Slide show...............................................98
a
U
2
3
E
z
13
First Steps
Inserting the Battery
Insert a Rechargeable Li-ion Battery EN-EL10 (supplied) into the camera.
• Charge the battery before the first use or when the battery is running low
1
2
Slide the battery-chamber/memory
card slot cover in the direction
indicated by the arrow ( ) and open
1
the cover ( ).
2
Insert the battery.
Confirm that the battery’s positive (+) and
negative (–) terminals are oriented correctly as
shown on the label at the battery chamber
opening, and insert the battery.
Use the battery to push up the orange battery
latch in the direction indicated by the arrow (
)
1
and fully insert the battery ( ).
2
The battery latch will spring back into place when
the battery is fully inserted.
B Inserting the Battery
Inserting the battery upside down or backwards
could damage the camera. Be sure to check that
the battery is in the correct orientation.
3
Close the battery-chamber/memory
card slot cover.
14
Inserting the Battery
Removing the Battery
Close the slide cover to turn the camera off
and the monitor have turned off before opening
the battery-chamber/memory card slot cover.
To eject the battery, open the battery-chamber/
memory card slot cover and slide the orange
battery latch in the direction indicated by the
arrow ( ). The battery can then be removed by
1
hand ( ).
2
• Note that the battery and memory card may become hot during use; observe
due caution when removing the battery.
B Notes on the Battery
• Be sure to read and follow the warnings for the battery on page iii and the section, “The Battery”
• If the battery will not be used for an extended period, recharge it at least once every six months
and run it flat before returning it to storage.
15
Charging the Battery
Charge the supplied Rechargeable Li-ion Battery EN-EL10 inserted into the
camera, by connecting the supplied Charging AC Adapter EH-68P to the camera
via the supplied USB Cable UC-E6, and then plugging the Charging AC Adapter
into an electrical outlet.
1
Prepare the Charging AC Adapter EH-
68P.
If a plug adapter* is included, attach the plug
adapter to the plug on the Charging AC
Adapter. Push the plug adapter firmly until it is
securely held in place. Once the two are
connected, attempting to forcibly remove the
plug adapter could damage the product.
* The shape of the plug adapter varies
according to the country or region in which the camera was purchased.
For Customers in Argentina
If the camera was purchased in Argentina, the shape of the Charging
AC Adapter EH-68P (AR) differs from that supplied in other countries,
and a plug adapter is not included. Proceed to step 2.
EH-68P (AR)
2
Be sure that the power-on lamp and the monitor are off.
3 Use the supplied USB cable to connect the Charging AC Adapter to the
camera.
USB cable
B Connecting the Cable
When connecting the cable, be sure that the connector is properly oriented. Do not use force when
connecting the cable to the camera. When disconnecting the cable, do not pull the connector at an
angle.
16
Charging the Battery
4
Plug the Charging AC Adapter into an
electrical power outlet.
The power-on lamp slowly blinks orange to indicate
that the battery is charging.
About 3 hours are required to charge a fully exhausted
battery.
The following chart explains power-on lamp status when the camera is plugged into the
electrical power outlet.
Power-on lamp
Description
Blinks slowly
(orange)
Battery charging.
Battery not charging. When charging is complete, the power-
on lamp stops blinking orange and turns off.
Off
•
The ambient temperature is not suited to charging. Charge
the battery indoors with an ambient temperature of 5 °C to
35 °C (41 °F to 95 °F).
•
A USB cable is not correctly connected, nor is a Charging AC
Adapter correctly plugged, or the battery is faulty.
Disconnect the USB cable or unplug the Charging AC
Adapter and correctly connect it again, or change the
battery.
Flickers (orange)
5
Disconnect the Charging AC Adapter from the electrical outlet and
then disconnect the USB cable.
17
Charging the Battery
B Notes on Charging AC Adapter
• The Charging AC Adapter EH-68P is for use only with compatible devices. Do not use with another
make or model of device.
• The EH-68P is compatible with AC 100-240 V, 50/60 Hz electrical outlets. When using in other
countries, use a plug adapter (available commercially) as necessary. For more information about
plug adapters, consult your travel agency.
• The Charging AC Adapter EH-68P is for charging the battery inserted into the camera. When the
camera is connected to the Charging AC adapter, the camera cannot be turned on.
• Do not, under any circumstances, use another make or model of AC adapter other than Charging
AC Adapter EH-68P or USB-AC adapter. Failure to observe this precaution could result in
overheating or in damage to the camera.
C AC Power Source
from an electrical outlet and operated for shooting or playback.
• Do not, under any circumstances, use another make or model of AC adapter other than EH-62D.
Failure to observe this precaution could result in overheating or in damage to the camera.
D Charging Using Computer or Battery Charger
• Connecting the COOLPIX S80 to a computer also charges the Rechargeable Li-ion Battery EN-EL10
ion Battery EN-EL10 without the camera.
18
Charging the Battery
Turning On and Off the Camera
To turn on the camera, open the slide cover.
After the power-on lamp (green) lights for a moment,
the monitor will turn on.
To turn off the camera, close the slide cover.
When the camera turns off, both the monitor and
power-on lamp will turn off.
B Note on Opening the Slide Cover
Be sure to keep your fingers away from the lens when opening the slide cover.
D Power Saving Function (Auto Off)
If no operations are performed for a while, the monitor will turn off, the camera will enter standby
mode, and the power-on lamp will blink.
While the power-on lamp is blinking, press the shutter-release button to reactivate the monitor.
• Camera enters standby mode in about a minute (default setting) during shooting or playback
mode.
• The time allowed to elapse before the camera enters standby mode can be changed from the
is activated to prevent screen burn when no operations are performed for about a minute (default
19
Setting Display Language, Date and Time
A language-selection dialog is displayed the first time the camera is turned on.
1
Open the slide cover to turn on the camera.
The power-on lamp (green) will light for a moment and
the monitor will turn on.
2
3
Tap the desired language.
Language
If the desired language is not displayed, tap B
or C to view other language options.
Čeština
Deutsch
Español
Français
Dansk
English
Ελληνικά
For more information about operating the
Indonesia
Tap Yes.
Date
Set time and date?
If No is tapped, the date and time will not be
set.
Yes
No
4
Tap E or F to select your home
Home time zone
Tap J to return to the previous screen.
London
Casablanca
D Daylight Saving Time
If daylight saving time is in effect, tap p in the time
zone selection screen displayed in step 4 to turn on the
daylight saving time function.
Home time zone
London
When the daylight saving time function is enabled, W
is displayed at the top of the monitor.
Casablanca
To turn off the daylight saving time function, tap p
again.
20
Setting Display Language, Date and Time
5
6
7
Tap the order in which the day,
month, and year are displayed.
Date
YMD
MDY
DMY
:
01 2010 00 00
01
Edit the date and time.
Date
Tap the desired item and A or B to edit the
highlighted item.
YMD
MDY
DMY
:
2010 00 00
01
01
Tap I.
Date
MDY
The clock is activated and the camera enters
shooting mode.
YMD
DMY
:
11 2010 14 30
15
C Imprinting and Changing the Date and Time
• To imprint the date on picture when shooting, enable date imprint from the Date imprint option
daylight saving time settings.
21
Inserting Memory Cards
Recorded data are stored in the camera’s internal memory (approximately 79 MB)
If a memory card is inserted in the camera, data are automatically stored on
the memory card and data recorded to the memory card can be played back,
deleted or transferred. Remove the memory card to store data in the internal
memory, or play back, delete or transfer data from the internal memory.
1
Be sure that the power-on lamp and the
monitor are off and open the battery-
chamber/memory card slot cover.
Be sure to turn off the camera before opening the
battery-chamber/memory card slot cover.
2
Insert the memory card.
Slide the memory card in the correct orientation
shown at right until it clicks into place.
Close the battery-chamber/memory card slot
cover.
B Inserting Memory Cards
Inserting the memory card upside down or
backwards could damage the camera or the
memory card. Be sure that the memory card is in the
correct orientation.
Removing Memory Cards
Before removing memory cards, close the slide
cover to turn the camera off and be sure that the
power-on lamp and monitor are off. Open the
battery-chamber/memory card slot cover and
press the card in ( ) to partially eject the card.
1
The card can then be removed by hand ( ). Do
2
not attempt to remove the card at an angle.
• Note that the battery and memory card may
become hot during use; observe due caution when removing the memory card.
22
Inserting Memory Cards
B Formatting Memory Cards
If the message at right is displayed when the camera is
turned on, the memory card must be formatted before
deletes all pictures and other data on the memory
card. Be sure to make copies of any pictures you wish
to keep before formatting the memory card.
Card is not formatted.
Format card?
Yes
No
Tap Yes to format. When the confirmation dialog is
displayed, tap Yes. To start formatting, tap OK.
• Do not turn the camera off or open the battery-chamber/memory card slot cover until formatting
is complete.
• Be sure to use the COOLPIX S80 to format memory cards previously used in other devices the first
B The Write Protect Switch
Memory cards are equipped with a write protect switch. When
Write protect switch
this switch is in the “lock” position, data cannot be written to,
or deleted from, the memory card. If the switch is in the “lock”
position, unlock it by sliding the switch to the “write” position
to record or delete pictures, or to format the memory card.
B Memory Cards
• Use only Secure Digital memory cards.
• Do not perform the following during formatting, while data is being written to or deleted from the
memory card, or during data transfer to a computer. Failure to observe this precaution could result
in the loss of data or in damage to the camera or memory card:
- Take out the battery or memory card
- Turn off the camera
- Disconnect the AC adapter
• Do not use a computer to format the memory card.
• Do not disassemble or modify.
• Do not drop, bend, or expose to water or strong physical shock.
• Do not touch the metal terminals with your fingers or metal objects.
• Do not affix labels or stickers to the memory card.
• Do not leave in direct sunlight, closed vehicles or areas exposed to high temperatures.
• Do not expose to humidity, dust, or corrosive gases.
23
Basic Photography and Playback: G (Easy Auto) Mode
Step 1 Turn the Camera On and Select
G
Easy Auto Mode
In G (easy auto) mode, the camera automatically selects the optimum shooting
mode by framing a picture, allowing you to easily take pictures using a shooting
1
Open the slide cover to turn on the camera.
The power-on lamp (green) will light for a moment and
the monitor will turn on.
G (easy auto) mode is initially activated at the time of
purchase. Proceed to step 4.
2
3
Tap the shooting mode icon.
T
W
36
Tap G.
Shooting mode
Easy auto mode
The camera enters G (easy auto) mode.
4
Check the battery level and the
number of exposures remaining.
Battery level indicator
l
Battery Level
Description
NO INDICATOR Battery fully charged.
Battery low.
Prepare to charge or
replace the battery.
T
B
W
36
N
Cannot take pictures.
Recharge or replace with
a fully charged battery.
Number of exposures remaining
Battery
exhausted.
Number of Exposures Remaining
Indicator is displayed when there are 50 or fewer exposures remaining.
The number of pictures that can be stored depends on the capacity of the internal
24
Step 1 Turn the Camera On and Select G Easy Auto Mode
Indicators Displayed in G (Easy Auto) Mode
Shooting mode
In easy auto mode, G,
e, f, g, h, j,
Vibration reduction
The effects of camera
shake are reduced.
or i is displayed to
indicate the shooting
mode selected by the
camera for the current
subject and framing.
T
W
36
Internal memory indicator
Indicates that images will be stored in the camera’s internal memory (approximately
79 MB). When a memory card is inserted, C is not displayed and pictures will be
stored to memory card.
To reactivate the monitor after it is turned off by the power saving function in
B Note on Touch Shutter
At the default setting, the shutter can be released by simply tapping a subject in the monitor
B Note on Printing Pictures
When printing pictures taken at an Image mode setting of p 3968×2232 (default setting), the
D Functions Available in G (Easy Auto) Mode
• When the camera is pointed at a human face, the face detection function, with which the camera
D Vibration Reduction
• Set Vibration reduction to Off when using a tripod to stabilize the camera during shooting.
25
Step 2 Frame a Picture
1
Ready the camera.
Hold the camera steadily in both hands, keeping your
fingers and other objects away from the lens, flash, AF-
assist illuminator, microphone, and speaker.
When taking pictures in portrait (“tall”) orientation, turn
the camera so that the built-in flash is above the lens.
2
Frame the picture.
Shooting mode icon
When the camera automatically selects the
optimum scene mode, the shooting mode
When the camera detects a face, that face will
be framed by a yellow double border (focus
area).
T
W
36
Up to 12 faces can be detected. If more than
one face is detected, the face closest to the
camera will be framed by a double border, and the others by a single border.
When taking pictures of subjects other than people, or framing a subject with which no
face is detected, a focus area will not be displayed. Frame the picture so that the
intended subject is at or near the center of the frame.
B Notes on G (Easy Auto) Mode
• The desired scene mode may not be selected in certain condition. In this case, select another
shooting mode.
• When digital zoom is in effect, shooting mode is G.
26
Step 2 Frame a Picture
Using the Zoom
Tap j or k to activate optical zoom.
Digital zoom
Optical zoom
• To enlarge the subject: tap j.
• To capture a wide area: tap k.
• The zoom position is set at the
maximum wide-angle position when
the camera is turned on.
Zoom in
T
Zoom out
W
• A zoom indicator is displayed in the
monitor during zooming.
Digital Zoom
When the camera is zoomed in to the maximum optical zoom position, touching
and holding j triggers digital zoom. The subject is magnified up to 4× the
maximum optical zoom ratio.
The camera focuses at the center of the frame and the focus area is not displayed
when digital zoom is in effect.
T
T
W
W
Maximum optical zoom
Digital zoom enabled
C Digital Zoom and Interpolation
Unlike optical zoom, digital zoom uses a digital imaging process known as
interpolation to magnify images, resulting in slight deterioration of picture
quality.
Interpolation is applied at zoom positions beyond V. When zoom is
increased beyond the V position, interpolation is initiated and the zoom
indicator turns yellow to indicate that interpolation is being applied. The
position of V moves to the top as image size decreases, allowing for
confirmation of the zoom positions at which shooting without interpolation is
T
W
Small image size
27
Step 3 Focus and Shoot
1
Press the shutter-release button
halfway.
Focus is locked when the shutter-release
When a face is detected, it is framed by the
double border indicating the active focus
area. When the subject is in focus, the double
border turns green.
1/250 F3.6
Shutter speed Aperture
When no face is detected, the camera
automatically selects the focus area (up to nine areas) suitable to the shooting scene.
When digital zoom is used, the focus area is
not displayed and the camera focuses at the
center of the frame. Once focus has been
acquired, the focus indicator will glow green.
Focus indicator
Shutter speed and aperture value are displayed when the shutter-release button is
pressed halfway.
The focus and exposure remain locked while the shutter-release button is pressed
halfway.
When the camera detects subject movement or camera shake and increases shutter
If the focus area or the focus indicator blinks red when the shutter-release button is
pressed halfway, the camera is unable to focus. Modify the composition and press the
shutter-release button halfway again.
2
Press the shutter-release button the
rest of the way down.
The shutter is released and the picture will be
recorded to the memory card or internal
memory.
28
Step 3 Focus and Shoot
B During Recording
While pictures are being recorded, the number of exposures remaining will blink. Do not open the
battery-chamber/memory card slot cover while pictures are being recorded. Cutting power or
removing the memory card in these circumstances could result in loss of data or in damage to the
camera or card.
B Autofocus
Autofocus may not perform as expected in the following situations. In some rare cases, the subject
may not be in focus despite the fact that the focus area or the focus indicator glows green.
• Subject is very dark
• Objects of sharply differing brightness are included in the scene (e.g. the sun behind the subject
makes that subject appear very dark)
• No contrast between the subject and surroundings (e.g. a portrait subject, wearing a white shirt, is
standing in front of a white wall)
• Several objects are at different distances from the camera (e.g. the subject is inside a cage)
• Regular geometric patterns (e.g. window blind or windows in a skyscraper)
• Subject is moving rapidly
In the situations noted above, try pressing the shutter-release button halfway to refocus several
alternate subject is at the same distance from the camera as the intended subject while the shutter-
release button is pressed halfway.
B Note on Face Detection
C Touch Shutter
At the default setting, the shutter can be released by simply tapping a subject in the monitor
the Touch AF/AE option, which allows the camera to set the focus and exposure on the subject
that is tapped on the monitor. When using the Touch AF/AE option, the picture is taken by pressing
C Blink Warning Screen
When the camera detects that portrait subjects may have blinked when a picture was taken in face
the monitor.
D AF-assist Illuminator and Flash
all the way down.
29
Step 4 Playing Back and Deleting Pictures
Playing Back Pictures (Playback Mode)
Tap c.
Shooting
Playback
:
15 11 2010 15 30
0004. JPG
T
W
4/
4
36
Internal memory indicator
The last picture taken will be displayed in full-frame playback mode.
Drag the current picture to display previous or subsequent picture. Use two fingers to scroll
Display the previous picture
Display the subsequent picture
:
:
15 11 2010 15 30
15 11 2010 15 30
0004. JPG
0004. JPG
4/
4/
4
The previous or subsequent picture may appear briefly at low resolution immediately after it
is dragged into view.
Tap the shooting mode icon (G) displayed at upper left in the monitor or press the shutter-
release button to return to shooting mode.
is displayed when pictures stored in the camera’s internal memory are played back.
C
When a memory card is inserted in the camera, C is not displayed and pictures stored on the
memory card are played back.
C Options Available in Playback Mode
C Viewing Pictures
• Pictures taken in portrait (“tall”) orientation will be rotated automatically (A 11). The rotating
• When the monitor has turned off in standby mode to save power, press the shutter-release button
30
Step 4 Playing Back and Deleting Pictures
Deleting Unwanted Pictures
1
Play back a picture to be deleted, tap
the bottom tab to display the setting
2
Tap the desired delete option.
Current image: Delete the currently
displayed full-frame picture or movie
Erase selected images: Select multiple pictures
and delete them. See “Operating the Erase
Selected Images Screen” for more information.
All images: Delete all pictures.
Delete
Current image
Erase selected images
All images
Select either Erase selected images or All images when performing the step 1 in
3
Tap Yes on the delete confirmation
dialog.
Deleted pictures cannot be recovered.
Delete
Erase 1 image?
To exit without deleting the picture, tap J or
No.
Yes
No
Operating the Erase Selected Images Screen
1
Tap a picture to display y.
To deselect the picture, tap the picture again
Erase selected images
and y will be hidden.
Tap n or o to change the number of
pictures displayed.
2
Display y to all pictures to delete and tap I to apply the selection.
The confirmation screen is displayed. Follow the onscreen instructions for more operations.
B Notes on Deleting Pictures
• Once deleted, pictures cannot be recovered. Transfer important pictures to a computer before
deleting them.
31
Basic Shooting Functions
m Using the Flash
Flash mode can be selected to suit the shooting conditions.
• When ISO sensitivity is set to Auto, the flash has a range of 0.5-4.0 m (1 ft.
8 in.-13 ft.) at the maximum wide-angle zoom position and a range of 0.5-2.5 m
(1 ft. 8 in.-8 ft. 2 in.) at the maximum telephoto zoom position.
Off are available. When a Auto is selected, the camera sets the flash mode
according to the automatically selected scene mode.
a
Auto
Flash fires automatically when lighting is poor.
Auto with red-eye reduction
b
Suited to pictures of people, this option reduces the “red-eye” phenomenon
c
Off
Flash will not fire even when lighting is poor.
X
Fill flash
Flash fires whenever a picture is taken. Use to “fill-in” (illuminate) shadows and
back-lit subjects.
d
Slow sync
a (auto) is combined with slow shutter speed.
Suited to evening and night portraits that include background scenery.
Flash illuminates main subject; slow shutter speeds are used to capture
background at night or under dim lighting.
33
Basic Shooting Functions
Setting the Flash Mode
1
2
Tap the left tab to display the setting
mode icon.
The flash mode menu is displayed.
T
W
Tap the desired flash mode icon.
Flash mode
Auto
Tap J to return to the previous screen.
To hide the setting controls after applying the
setting, tap the tab again.
B Shooting When the Flash is Disabled (c) or Lighting is Poor
• The noise reduction function may be activated with some shooting conditions such as dim
lighting. More time than usual is required to record pictures to which noise reduction is applied.
B Note on Using the Flash
When using the flash, reflections from dust particles in the air may appear as bright spots in pictures.
To reduce these reflections, set the flash to c (off).
C The Flash Indicator
The flash indicator shows flash status when the
shutter-release button is pressed halfway.
• On: Flash will fire when picture is taken.
• Blinks: Flash charging. Wait a few seconds and try
again.
• Off: Flash will not fire when picture is taken.
1/250 F3.6
If the battery is low, the monitor will turn off, and
remain off, while the flash charges.
34
Basic Shooting Functions
C The Flash Mode Setting
The default flash mode setting varies with shooting mode.
• G (easy auto) mode: a (auto)
• A (auto) mode: a (auto)
• F (smart portrait): fixed at a (auto) when Off is selected for Blink proof; c (off) when On is
There are functions with which the flash cannot be enabled. See “Camera Settings That cannot be
The flash mode setting applied in A (auto) mode is stored in the camera’s memory even after the
camera is turned off.
C Red-eye Reduction
This camera uses advanced red-eye reduction (“In-Camera Red-Eye Fix”). To reduce red-eye, a series
of low-intensity pre-flashes fire before the main flash. In addition, if the camera detects red-eye when
a picture is taken, the affected area is processed to reduce red-eye before the picture is saved. Note
the following when shooting:
• Due to the pre-flashes, there is a longer than usual interval between the time the shutter-release
button is pressed and the time the shutter is released.
• More time than usual is required to record pictures.
• Red-eye reduction may not produce the desired results in some situations.
• In extremely rare instances, areas not subject to red-eye may be affected by red-eye reduction
processing; in these cases, choose another flash mode and try again.
35
Basic Shooting Functions
n Taking Pictures with the Self-timer
The camera is equipped with a ten-second and two-second timer for self-portraits.
This feature is useful for reducing the effects of camera shake that occurs when
pressing the shutter-release button. The self-timer setting can be selected from 10
or 2 seconds duration. When using the self-timer, use of a tripod is recommended.
using a tripod to stabilize the camera.
1
Tap the bottom tab to display the
self-timer icon.
T
W
OFF
0.0
2
Tap 10s or 2s.
10s (ten seconds): Use on important occasions,
such as weddings
Self-timer
Off
2s (two seconds): Use to prevent camera shake
The selected self-timer mode is displayed.
Tap J to return to the previous screen.
To hide the setting controls after applying the
setting, tap the tab again.
3
Frame the picture and press
the shutter-release button
halfway.
Focus and exposure will be locked.
1/250 F3.6
36
Basic Shooting Functions
4
Press the shutter-release
button the rest of the way
down.
The self-timer starts, and the
number of seconds remaining
before the shutter is released is
displayed in the monitor. The self-
timer lamp blinks while the timer is
counting down. About one second
before the shutter is released, the
lamp stops blinking and glows
steadily.
When the shutter is released, the
self-timer turns off.
To stop the timer before a picture is
taken, press the shutter-release button again.
B Note on Self-timer
There are functions with which this setting cannot be enabled. See “Camera Settings That cannot be
37
Basic Shooting Functions
A Image Mode (Image Quality/Image Size)
Image mode refers to the combination of image size and image quality
(compression) at which pictures are recorded. Choose the image mode best
suited to the manner in which pictures will be used and the capacity of the
internal memory or memory card. The higher the image mode setting, the larger
the size at which it can be printed or displayed without appearing noticeably
“grainy,” but limiting the number of pictures that can be recorded.
Option
Size (pixels)
Description
Higher quality than suitable for
enlargements or high-quality prints. The
compression ratio is approximately 1:4.
R
Q 4320×3240P
4320 × 3240
4320 × 3240
3264 × 2448
2592 × 1944
R 4320×3240
R 3264×2448
L 2592×1944
Best choice in most situations. The
compression ratio is approximately 1:8.
Smaller size than
pictures to be stored. The compression
ratio is approximately 1:8.
Suited to display on a computer monitor.
The compression ratio is approximately 1:8.
,
, or allows more
R R
L
M 2048×1536
2048 × 1536
1024 × 768
N 1024×768
Suited to full-screen display on a television
with an aspect ratio of 4:3, or distribution by
e-mail or the web. The compression ratio is
approximately 1:8.
O 640×480
640 × 480
Pictures with an aspect ratio of 16:9 are
recorded.
The compression ratio is approximately 1:8.
p 3968×2232
(default setting)
3968 × 2232
1
2
Tap the bottom tab to display the
image mode icon.
T
W
OFF
0.0
Tap the desired image mode icon.
Image mode
3968×2232
Tap J to return to the previous screen.
To hide the setting controls after applying the
setting, tap the tab again.
38
Basic Shooting Functions
B Note on Printing Pictures
When printing pictures taken at an Image mode setting of p 3968×2232 (default setting), the
edges of pictures may be cropped, preventing printing of complete pictures.
It may be possible to print complete pictures if settings on the printer are applied so that borders are
printed around pictures (borderless printing not enabled).
Refer to the documentation supplied with the printer or consult the digital photo lab for further
details to make sure that the printer supports printing at an aspect ratio of 16:9.
C Image Mode
• The setting can also be changed in shooting modes other than G (easy auto) mode (except
movie recording).
• Changes made to this setting apply to all shooting modes (except movie recording).
C Number of Exposures Remaining
The following table lists the approximate number of pictures that can be stored in internal memory
and on a 4 GB memory card. Note that the number of pictures that can be stored will differ
depending on the composition of the picture (due to JPEG compression). In addition, this number
may vary depending upon the make of memory card, even when the memory cards have the same
specified capacity.
Internal memory
(approx. 79 MB)
Memory card
Setting
Print size* (cm/in.)
(4 GB)
Q
R
R
4320×3240P
4320×3240
3264×2448
2592×1944
2048×1536
1024×768
11
23
550
1100
1910
2940
4640
15000
24100
1720
Approx. 36 × 27/14 × 10.5
Approx. 36 × 27/14 × 10.5
Approx. 28 × 21/11 × 8
Approx. 22 × 16/8.5 × 6.5
Approx. 17 × 13/7 × 5
Approx. 9 × 7/3.5 × 2.5
Approx. 5 × 4/2 × 1.5
40
62
L
M
N
O
p
97
316
563
36
640×480
3968×2232
Approx. 34 × 19/13 × 7
* Print size at an output resolution of 300 dpi. Print sizes are calculated by dividing the
number of pixels by printer resolution (dpi) and multiplying by 2.54 cm (1 in.). However, at
the same image size, pictures printed at higher resolutions will print smaller than the size
indicated, and those printed at lower resolutions will print larger than the size indicated.
• The number of exposures remaining is displayed on the shooting display when 50 or fewer remain
• If there are 10,000 or more pictures saved in the camera, “9999” is displayed on the playback screen
as the current frame number or total number of frames.
39
Basic Shooting Functions
C Image Mode Setting and Monitor Display
Monitor display in shooting and playback modes varies as indicated below according to the image
mode setting.
p
Q, R, R, L, M, N, O
T
T
W
W
36
36
40
Basic Shooting Functions
q
Tapping the Monitor to Release the Shutter (Touch Shutter)
Pictures can be taken by simply tapping the monitor.
•
Touch shutter is set by default. Proceed to step 3.
1
Tap the bottom tab to display the
touch shooting icon.
T
W
OFF
0.0
2
3
Tap q (touch shutter).
Tap J to return to the previous screen.
Touch shooting
Touch shutter
To hide the setting controls after applying the
setting, tap the tab again.
Tap the desired subject to take a
picture.
When a face is detected in G (easy auto)
mode, it is framed by a border. Tap a detected
face to set the focus and exposure on that
face.
T
W
36
When no face is detected, the camera focuses
on the area that is tapped.
Do not use force when tapping the monitor as this may cause slight movement of the
camera, resulting in blurred pictures.
When digital zoom is in effect, the camera focuses on the subject in the center of the
frame.
The shutter-release button can also be used when the touch shutter option is selected.
If X is displayed when the monitor is
tapped, the shutter cannot be released. Tap
an area within X or a border displayed
when the camera detects a face.
T
W
36
41
Basic Shooting Functions
B Notes on Touch Shutter
one picture can be taken at a time using the touch shutter function.
• Prevent shooting with accidental tapping of the monitor in G (easy auto) mode, A (auto) mode,
setting, the shutter is not released when the monitor is tapped.
• When shooting subjects with which autofocus may not perform as expected, the subject may not
camera locks focus and releases the shutter after ten or two seconds.
42
Basic Shooting Functions
C Shooting Modes That Support Touch Shutter
The touch shutter can be used in G (easy auto) mode and other shooting modes. Touch shutter
operation differs according to the current shooting mode as follows.
Shooting mode
Touch shutter operation
•
•
When a face is detected by the camera, it is framed by
a border. Tap a detected face to set the focus and
exposure on that face.
When no face is detected, focus is set for the area
tapped.
Party/indoor, Beach, Snow,
Close-up, Food, Museum, Copy,
and Backlighting scene modes
Tap the intended subject. Focus and exposure are set for
the area tapped. When the camera detects more than
one face, tap a face framed by a single border to set
focus and exposure for that face.
Only a border displayed by the face detection function
can be selected. When the camera detects more than
one face, tap a face framed by a single border to set
focus and exposure for that face.
Portrait and Night portrait scene
Landscape, Sunset, Dusk/dawn,
Focus and exposure are set for the same focus area used
Night landscape, Fireworks show, when pictures are taken by pressing the shutter-release
and Panorama assist scene modes
button. See “Selecting a Scene Mode to Take Pictures
Touch shutter cannot be enabled.
C Touch Shutter Function When Recording Movies
Touch shutter is also available when recording movies. Movie recording can be initiated or stopped
C Touch Shooting Setting
The touch shooting setting applied in A (auto) mode is stored in the camera’s memory even after
the camera is turned off.
43
Basic Shooting Functions
r Tapping the Monitor to Focus (Touch AF/AE)
The touch shooting setting can be changed from Touch shutter (default setting)
to Touch AF/AE.
Tap a subject in the monitor to select the area at which the camera focuses. Press
the shutter-release button halfway to lock focus and exposure for the area tapped,
and press the shutter-release button the rest of the way down to take the picture.
1
2
3
Tap the bottom tab to display the
touch shooting icon.
The menu of the touch shooting setting is
displayed in the monitor.
T
W
OFF
0.0
Tap r (touch AF/AE).
Tap J to return to the previous screen.
Touch shooting
Touch AF/AE
To hide the setting controls after applying the
setting, tap the tab again.
Tap the subject at which the camera
focuses.
When faces are detected in G (easy auto)
mode, only those faces surrounded by the
frame can be tapped to change the focus
subject. When multiple faces are detected, tap
a face framed by a single border to move the
focus area to that face.
T
W
36
When no face is detected, the camera focuses on the area that is tapped.
u or a double border will be displayed at the area tapped.
When digital zoom is in effect, the focus area cannot be selected.
To cancel the focus area selection, tap a displayed at the left side of the monitor.
If a position at which focus cannot be
acquired is tapped, X will be displayed in
the monitor. Tap another position inside X.
T
W
36
44
Basic Shooting Functions
4
Press the shutter-release button to take a picture.
Press the shutter-release button halfway to acquire focus and exposure
and press it all the way down to release the shutter.
B Note on Touch AF/AE
When shooting subjects with which autofocus may not perform as expected, the subject may not
C Shooting Modes That Enable Touch AF/AE Function
The touch AF/AE can be used in G (easy auto) mode and other shooting modes. Touch AF/AE
operation differs according to the current shooting mode as follows.
Shooting mode
Touch AF/AE operation
•
•
When the camera detects a face, only a face framed by
a border can be selected. When the camera detects
more than one face, tap a face framed by a single
border to set focus and exposure for that face. The
single border changes to a double border.
When no face is detected, focus is set for the area
tapped.
Party/indoor, Beach, Snow,
Close-up, Food, Museum, Copy,
and Backlighting scene modes
Focus and exposure are set for the area tapped.
Only a border displayed by the face detection function
can be selected. When the camera detects more than
one face, tap a face framed by a single border to move
the focus area to that face.
Portrait and Night portrait scene
Landscape, Sunset,
Dusk/dawn, Night landscape,
Fireworks show, and Panorama
Touch AF/AE cannot be enabled.
45
Basic Shooting Functions
C Touch Shooting Setting
The touch shooting setting applied in A (auto) mode is stored in the camera’s memory even after
the camera is turned off.
D Taking Pictures of Subjects with Which Autofocus may not Perform as
Expected
pressing the shutter-release button halfway to refocus several times, or try the following techniques.
1
2
3
AE for the touch shooting setting.
Touch shooting
Touch AF/AE
Tap another subject that is as far from the camera as the
desired subject.
T
W
36
Press the shutter-release button halfway.
• The camera focuses on the subject and the
focus area glows green.
• Exposure is locked for the subject on which
focus is acquired when the shutter-release
button is pressed halfway.
1/250 F3.6
4
5
Continue holding down the shutter-release button halfway
and recompose the picture.
• Be sure to maintain the same distance between the
camera and the subject while the shutter-release button
is pressed halfway.
1/250 F3.6
Press the shutter-release button the rest of the way down
to take the picture.
46
Basic Shooting Functions
o Changing Brightness Using Exposure Compensation
Exposure compensation is used to alter exposure from the value suggested by the
camera to make pictures brighter or darker.
1
Tap the bottom tab to display the
exposure compensation icon.
T
W
OFF
0.0
2
Drag the slider to change the
exposure compensation value.
Exposure compensation
To make the picture brighter, apply positive
(+) exposure compensation.
-
2
-
1
+
1
+
2
0
To make the picture darker, apply negative (–)
exposure compensation.
Tap J to return to the previous screen.
3
Tap I.
Exposure compensation
To hide the setting controls after applying the
setting, tap the tab again.
To cancel the exposure compensation, return
to step 1, revert the value to [0], and tap I.
-
2
-
1
+
1
+
2
0
C Exposure Compensation Value
memory even after the camera is turned off.
47
More on Shooting
Selecting a Shooting Mode
The following shooting modes can be selected.
G
Easy auto mode
By simply framing a picture, the camera automatically selects the optimum shooting
mode.
A
Auto mode
Pictures can be taken with the flash mode or macro mode setting. Other settings can
be made, such as the continuous shooting setting or the “subject tracking” option,
which moves the active focus area to track the selected subject.
C
Scene mode
Camera settings are automatically optimized for the selected scene.
F
Smart portrait
The camera uses face detection to detect human faces, and then automatically
releases the shutter when a smile is detected. The skin softening option can be used to
make skin tones of human faces displayed smoothly.
D
Movie
Shoot movies with sound recorded via the built-in microphone.
1
Tap the shooting mode icon in
shooting mode.
The shooting mode selection menu is
displayed.
T
W
36
2
Tap the desired shooting mode icon.
Shooting mode
Easy auto mode
The camera enters the selected shooting
mode.
To select a scene mode, first tap C (scene),
and then tap the icon of the desired scene
To return to the current shooting mode, tap
the shooting mode icon at the upper left of the screen or press the shutter-release
button.
48
G (Easy Auto) Mode
Automatic Scene Selection
The camera automatically selects one of the following scenes when pointing the
camera at a subject.
• G Auto mode (general use)
Focusing in Easy Auto Mode
When G or i is displayed, the camera
automatically selects one or more of the nine
focus areas containing the subject closest to
the camera.
T
Press the shutter-release button halfway to
activate the focus area. When the shutter-
release button is pressed halfway, the focus
W
36
area (up to nine areas) selected by the camera will be displayed in the monitor.
Face Detection
When the camera is pointed at a human face, face detection, with which the
camera automatically detects that face and focus on it, starts. The face detection
function is activated in the following situations.
B Notes on Face Detection
• The camera may be unable to recognize faces in the following situations:
- When faces are partially hidden by sunglasses or other obstructions
- When faces take up too much or too little of the frame
• When the frame includes more than one face, the faces detected by the camera and the face on
which the camera focuses depend upon a variety of factors, including the direction in which the
faces are looking.
expected, and the subject may not be in focus despite the fact that the double border glows
green. Should this occur, refocus on another subject positioned at the same distance from the
49
G (Easy Auto) Mode
C Motion Detection
In G (easy auto) mode or A (auto) mode, when the camera detects subject movement or camera
shake, ISO sensitivity and shutter speed are increased to reduce blurring. In this case, the shutter
speed indicator will turn green.
• Motion detection may be unable to completely eliminate the effects of subject movement and
camera shake in some situations.
• Motion detection may not function if the subject exhibits significant movement or is too dark.
• The pictures taken using motion detection may be somewhat “grainy” in appearance.
50
Shooting in A (Auto) Mode
Shooting settings such as flash mode and macro mode can be made. The
Continuous setting or the Subject tracking option, with which the active focus
area moves to track the selected subject, can also be made or applied.
1
2
3
Tap the shooting mode icon in
shooting mode.
The shooting mode selection menu is
displayed.
T
W
36
Tap A.
Shooting mode
Auto mode
The camera enters A (auto) mode.
Tap the left or bottom tab to display
check or adjust the settings.
Tap a setting icon to adjust the setting.
T
W
36
51
Shooting in A (Auto) Mode
4
Frame the subject and take a
picture.
When the camera detects a face, a
yellow double border (focus area) is
displayed around that face. When
the shutter-release button is pressed
halfway, the camera focuses on that
T
W
36
When taking pictures of subjects other than people, or framing a subject with which no
face is detected, the camera automatically selects one or more of the nine focus areas
area (up to nine areas) turns green.
A picture is taken when the shutter-release button is pressed all the way down.
At the default setting, the shutter can be released by simply tapping a subject in the
option can be changed to the Touch AF/AE option, which allows the camera to set the
focus and exposure on the subject that is tapped on the monitor. When using the
Touch AF/AE option, the picture is taken by pressing the shutter-release button
D More Information
52
Adjusting the A (Auto) Mode Setting
In A (auto) mode, the camera settings indicated below can be adjusted by
tapping the tabs to display the setting controls.
• Each icon also indicates the current setting.
• Tap the icon of the desired item to display the setting screen for that item.
• To hide the setting controls, tap the tab again.
T
T
W
W
OFF
36
1 2
9
8
T
T
OFF
AUTO
W
W
AUTO
0.0
36
3
4
5
6
7
1
2
3
4
Touch shooting*
6
7
8
9
q
5
* The settings applied in A (auto) mode are stored in the camera’s memory even after the
camera is turned off.
C Camera Settings That cannot be Applied Simultaneously
Some shooting settings cannot be used with other functions. See “Camera Settings That cannot be
53
Adjusting the A (Auto) Mode Setting
p Macro Mode Setting
A (auto) M Tap the left tab M p Macro mode
Macro mode is used for taking pictures of objects as close as 7 cm (2.8 in.). Note
that the flash may be unable to light the entire subject at distances of less than
50 cm (1 ft. 8 in.).
1
Tap o.
Macro mode
On
2
Tap j or k and frame the picture.
The closest possible shooting distance may vary according to the
zoom position. The camera can focus at a closer distance when F
and the zoom indicator glow green and the zoom indicator is
positioned below I (wide-angle position). The camera can focus on
the subject as close as 7 cm (2.8 in.) to the lens at the maximum
wide-angle zoom position.
T
W
B Note on Macro Mode Setting
There are functions with which this setting cannot be enabled. See “Camera Settings That cannot be
C The Macro Mode Setting
• In G (easy auto) mode, the camera enters macro mode when i is selected.
macro mode when k Close-up or u Food is selected.
• In F (smart portrait) mode, macro mode is disabled.
54
Adjusting the A (Auto) Mode Setting
s Subject Tracking (Focusing on a Moving Subject)
A (auto) M Tap the bottom tab M Touch shooting
Touch shutter (default setting) to Subject tracking. Use this option to take
pictures of moving subjects. Tap the subject on which the camera will focus. The
focus area will automatically move to track the subject.
1
Tap s (subject tracking).
s (subject tracking) is enabled only in A
Touch shooting
Subject tracking
(auto) mode.
2
Register a subject.
Tap the desired tracking subject in the
monitor.
•
•
The subject is registered.
T
When the border framing the subject glows
red, the camera is unable to focus. Change
the composition and try again.
W
36
If the tapped area does not contain a subject
that can be registered, X will be displayed in the monitor. Tap a subject within X.
When the subject is registered, a yellow focus
area is displayed around that subject and the
camera begins tracking the subject.
Tap another subject to change a subject to
follow.
T
To cancel the registration of the subject, tap
a displayed at left in the monitor.
If the camera cannot track the registered
W
36
subject anymore, the focus area will disappear and the registration will be canceled.
Register the subject again.
55
Adjusting the A (Auto) Mode Setting
3
Press the shutter-release button to
take a picture.
The camera focuses on the focus area when
the shutter-release button is pressed halfway.
The focus area will glow green and focus will
be locked.
1/250 F3.6
When the camera is unable to focus, the focus
area will blink. Press the shutter-release button halfway again to focus.
If the shutter-release button is pressed halfway while the focus area is not displayed, the
camera automatically selects one or more of the nine focus areas containing the subject
Press the shutter-release button all the way down to release the shutter.
B Notes on Subject Tracking Mode
• Digital zoom is not available.
• The sound of the lens focus motor can be heard when the subject tracking function is working.
other setting is adjusted after the subject has been registered, subject registration will be
cancelled.
• It may be impossible to register the desired subject, or the camera may be unable to track the
registered subject or may begin tracking a different subject, if the subject is moving rapidly, if
there is a significant amount of camera shake, or if the camera detects a similar subject. The
camera’s ability to accurately track the registered subject is also dependent upon the size and
brightness of the subject.
out of focus despite the fact that the focus area glows green. In this situation, focus on another
subject which is at the same distance from the camera as the intended subject while the shutter-
C Touch Shooting Setting
Subject registration with subject tracking will be canceled when the camera is turned off.
56
Adjusting the A (Auto) Mode Setting
E ISO Sensitivity
A (auto) M Tap the bottom tab M E ISO sensitivity
Raising the ISO sensitivity reduces the amount of light needed to make an
exposure, allowing pictures to be taken in low light conditions. A higher sensitivity
also allows for faster shutter speeds, reducing blur caused by subject movement
or camera shake.
• High ISO sensitivity settings are useful when taking pictures in dim lighting,
when shooting without a flash, or when using the telephoto setting, but they
may also produce “noise” -- randomly spaced, brightly colored pixels -- in the
dark areas of images.
s
Auto (default setting)
Sensitivity is ISO 80 when there is sufficient lighting; the camera compensates by
raising sensitivity to a maximum of ISO 800 when lighting is poor.
Fixed range auto
Choose the range in which the camera automatically adjusts ISO sensitivity, from
ISO 80-200 or ISO 80-400. The camera will not raise sensitivity beyond the
maximum value in the selected range. Set the maximum value for ISO sensitivity for
effective control over the amount of “grain” that appears in images.
80, 100, 200, 400, 800, 1600, 3200, 6400
Sensitivity is locked at the specified value.
B Notes on ISO Sensitivity
disabled.
B Notes on ISO Sensitivity 3200 and 6400
• When ISO sensitivity is set to 3200 or 6400, Image mode settings are limited to M
2048×1536, N 1024×768, and O 640×480.
• When ISO sensitivity is set to 3200 or 6400, the image mode icon is displayed in red during
shooting.
57
Adjusting the A (Auto) Mode Setting
V Continuous
A (auto) M Tap the bottom tab M C Continuous
Enable continuous shooting or BSS (best shot selector).
U
Single (default setting)
One picture is taken each time the shutter-release button is pressed.
V
Continuous
While the shutter-release button is held down, up to 6 pictures are taken at a rate of
about 0.9 frame per second (fps) when Image mode is set to p 3968×2232.
D
W
BSS (Best Shot Selector)
The “best shot selector” is recommended when shooting with the flash off or the
camera zoomed in, or in other situations in which inadvertent motion can result in
blurred pictures. When BSS is on, the camera takes up to ten pictures while the
shutter-release button is held down. The sharpest picture in the series is
automatically selected and saved.
Multi-shot 16
Each time the shutter-release button is pressed, camera takes
16 pictures at about 7 frames per second (fps) and arranges
them in a single image.
•
Pictures are recorded at an image mode setting of L
(image size: 2560×1920 pixels). This setting cannot be
changed.
•
Digital zoom is not available.
B Notes on Continuous Shooting
•
When Continuous, BSS, or Multi-shot 16 is selected, the flash is disabled. Focus, exposure, and
white balance are fixed at the values determined with the first picture in each series.
The frame rate with continuous shooting may vary depending upon the current image mode
setting, the memory card used, or shooting condition.
•
B Note on BSS
BSS is effective when taking pictures of still subjects. BSS may not produce the desired results if the
subject moves or the composition changes while the shutter-release button is held down.
B Note on Multi-shot 16
with images. Avoiding bright objects such as the sun, reflections of the sun, and electric lights when
shooting with Multi-shot 16 enabled is recommended.
58
Adjusting the A (Auto) Mode Setting
w White Balance (Adjusting Hue)
A (auto) M Tap the bottom tab M w White balance
The color of light reflected from an object varies with the color of the light source.
The human brain is able to adapt to changes in the color of the light source, with
the result that white objects appear white whether seen in the shade, direct
sunlight, or under incandescent lighting. Digital cameras can mimic this
adjustment by processing images according to the color of the light source. This is
known as “white balance.” For natural coloration, choose a white balance setting
that matches the light source before shooting. Although the default setting, Auto,
can be used under most types of lighting, the white balance setting suited to a
particular light source can be specified manually to achieve more accurate results.
s
Auto (default setting)
White balance automatically adjusted to suit lighting conditions. Best choice in
most situations.
b
Preset manual
Neutral-colored object used as reference to set white balance under unusual
c
d
e
f
g
Daylight
White balance adjusted for direct sunlight.
Incandescent
Use under incandescent lighting.
Fluorescent
Use under fluorescent lighting.
Cloudy
Use when taking pictures under overcast skies.
Flash
Use with the flash.
B Note on White Balance Setting
59
Adjusting the A (Auto) Mode Setting
Preset Manual
Preset manual is effective with mixed lighting or to compensate for light sources
with a strong color cast (for example, to make pictures taken under a lamp with a
red shade look as though they had been taken under white light).
Follow the procedure below to measure the white balance value according to the
light source when shooting.
1
2
Place a white or gray reference object under the lighting that will be
used during shooting.
Tap the bottom tab to display the
w.
T
OFF
AUTO
W
AUTO
0.0
3
4
Tap b.
White balance
Preset manual
The camera zooms in to the position for
measuring white balance.
Measuring window
Frame the reference object in the
measuring window.
Preset manual
To apply the most recently measured value
for preset manual, tap Cancel.
Cancel
Measure
5
Tap Measure to measure a value for
preset manual.
Preset manual
The shutter is released and the new white
balance value is set. No picture is recorded.
Cancel
Measure
B Note on Preset Manual
A value for flash lighting cannot be measured with Preset manual. When shooting using the flash,
set White balance to Auto or Flash.
60
Shooting Suited to Scenes (Scene Mode)
Camera settings are automatically optimized for the selected subject type. The
following scene modes are available.
b Portrait
c Landscape
d Sports
h Sunset
l Museum
e
Night portrait f Party/indoor
i Dusk/dawn Night landscape
m Fireworks show n Copy
Z Beach
z Snow
j
k Close-up
o Backlighting
u
Food
p
Panorama assist
Selecting a Scene Mode
1
2
3
Tap the shooting mode icon in
Shooting mode
shooting mode to display the
shooting mode selection menu, and
tap C.
Scene
The scene mode selection screen is displayed.
Tap the desired scene icon.
Beach
The camera enters the selected scene mode.
Frame the subject and take a
picture.
A scene effect adjustment slider is
displayed in some scene modes. The
degree of effect applied to pictures
taken in the selected scene mode can
1/250 F3.6
C Displaying the Description of Each
Help selection
Scene Mode
When u is tapped in the scene selection screen (step
2), the help selection screen is displayed. Tap a scene
icon to display a description of the features of that
mode. Tap J to return to the help selection screen.
• Tap J in the help selection screen to return to the
monitor display shown in step 2.
61
Shooting Suited to Scenes (Scene Mode)
C Shooting Settings in Scene Mode
The shooting settings for each scene mode are shown below.
Touch
shooting
1,4
Exposure
compensation
Flash
Macro
Self-timer
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
b
c
d
e
f
Z
z
h
i
j
k
u
b
c
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
q
5
1
1,4
1
1
1
5
5
5
1
1
1
5
1
1
5
q
q
q
q
q
q
q
q
q
q
q
q
q
q
q
q
c
2
1
1
1
1
1
1
1
1
1
1
b
b
1, 3
1
a
a
1
1
c
c
c
a
c
c
c
1
1
1
1
l
m
n
o
p
1
1
1
1
1
1
1
c
X
1
c
1 The default setting can be changed by tapping the tabs to display the setting controls.
2 The flash mode setting is fixed at fill flash with slow sync with red-eye reduction.
3 The setting may change to slow sync with red-eye reduction.
4 Only a frame displayed by the face detection function can be selected.
5 Focus and exposure are set for the same focus area used when pictures are taken by
pressing the shutter-release button.
C Image Mode (Image Quality/Image Size) Setting
recording) applies. To change the image mode setting in scene mode, tap the bottom tab to display
the setting controls and tap A.
62
Shooting Suited to Scenes (Scene Mode)
Scene effect adjustment slider
Adjusting Scene Effect
The scene effect adjustment slider is
displayed in the scene modes listed below.
Tap or drag the scene effect adjustment
slider to adjust the degree of effect to be
applied to pictures taken in the selected
scene mode.
T
W
36
b Portrait, e Night portrait,
Z Beach, z Snow, j Night
landscape, o Backlighting
Darker
Brighter
u Food
More blue
Less vivid
More blue
More red
More vivid
More red
c Landscape, k Close-up
h Sunset, i Dusk/dawn
63
Shooting Suited to Scenes (Scene Mode)
Selecting a Scene Mode to Take Pictures (Features)
b Portrait
Use this mode for portraits.
•
When the camera detects a human face, that face will be
framed by a yellow double border (focus area). See “Face
If more than one face is detected, the face nearest to the
camera will be framed by a yellow double border (focus
area) and the other faces will be framed by a single border.
Tap the face framed by a single border to change the focus
•
•
•
The camera smoothes skin tones (in up to three faces) by applying the skin softening
If no faces are detected when the shutter-release button is pressed halfway, the camera
focuses on the subject at the center of the frame.
Digital zoom is not available.
The default setting for flash mode is b Auto with red-eye reduction.
•
•
•
c Landscape
Use this mode for vivid landscapes and cityscapes.
•
Camera focuses at infinity. The focus area or focus indicator
button is pressed halfway. Note, however, that objects in the
foreground may not always be in focus.
•
•
The flash does not fire and the flash mode is disabled.
•
d Sports
Use this mode for dynamic action shots that freeze the action
in a single shot and record motion in a series of pictures.
•
The camera focuses on the subject at the center of the frame.
The area focused can be changed by the touch shutter
While the shutter-release button is held down, up to 6
pictures are taken at a rate of about 0.9 frame per second
(fps) when image mode is set to p 3968×2232.
•
•
•
•
Focus, exposure, and white balance are fixed at the values determined with the first
picture in each series.
The frame rate with continuous shooting may vary depending upon the current image
mode setting, the memory card used, or shooting condition.
Continuous shooting is disabled and only one picture can be taken at a time when the
The flash does not fire and the flash mode is disabled.
•
•
64
Shooting Suited to Scenes (Scene Mode)
e Night portrait
O
Use this mode for portraits taken at sunset or at night. The flash
fires to light the portrait subject while preserving background
lighting to achieve a natural balance between the main subject
and background ambience.
•
When the camera detects a human face, that face will be
framed by a yellow double border (focus area). See “Face
•
If more than one face is detected, the face nearest to the camera will be framed by a
yellow double border (focus area) and the other faces will be framed by a single border.
The camera smoothes skin tones (in up to three faces) by applying the skin softening
•
•
If no faces are detected when the shutter-release button is pressed halfway, the camera
focuses on the subject at the center of the frame.
•
•
•
Digital zoom is not available.
The flash mode setting is fixed at fill flash with slow sync with red-eye reduction.
f Party/indoor
Captures the effects of candlelight and other indoor
background lighting.
•
•
•
Camera focuses on the subject at the center of the frame.
The area focused can be changed by the touch shutter
The default setting for flash mode is b Auto with red-eye
reduction. The flash mode setting may automatically switch
to slow sync with red-eye reduction.
As pictures are easily affected by camera shake, hold the camera steadily. In dark
Off when using a tripod to stabilize the camera.
Z Beach
Captures the brightness of such subjects as beaches or sunlit
expanses of water.
•
Camera focuses on the subject at the center of the frame.
The area focused can be changed by the touch shutter
•
picture brightness.
Use of a tripod is recommended in scene modes with which O is indicated. Set Vibration
65
Shooting Suited to Scenes (Scene Mode)
z Snow
Captures the brightness of such subjects as snowfields.
•
Camera focuses on the subject at the center of the frame.
The area focused can be changed by the touch shutter
•
picture brightness.
h Sunset
O
O
Preserves the deep hues seen in sunsets and sunrises.
•
•
•
Camera focuses on the subject at the center of the frame.
The default setting for flash mode is c Off.
picture color.
i Dusk/dawn
Preserves the colors seen in the weak natural light before
sunrise or after sunset.
•
Camera focuses at infinity. The focus area or focus indicator
button is pressed halfway. Note, however, that objects in the
foreground may not always be in focus.
The flash does not fire and the flash mode is disabled.
•
•
•
j Night landscape
O
Slow shutter speeds are used to produce stunning night
landscapes.
•
Camera focuses at infinity. The focus area or focus indicator
button is pressed halfway. Note, however, that objects in the
foreground may not always be in focus.
•
•
•
The flash does not fire and the flash mode is disabled.
Use of a tripod is recommended in scene modes with which O is indicated. Set Vibration
66
Shooting Suited to Scenes (Scene Mode)
k Close-up
Photograph flowers, insects and other small objects at close
range.
•
automatically zooms to the closest position at which it can
focus.
•
The closest possible shooting distance may vary according
to zoom position. The camera can focus at a closer distance
when F and the zoom indicator glow green and the zoom
indicator is positioned below I (wide-angle position). The
camera can focus on the subject as close as 7 cm (2.8 in.) at
the maximum wide-angle zoom position.
•
•
•
•
Note that the flash may be unable to light entire subject at distances of less than 50 cm
(1 ft. 8 in.).
Camera focuses on the subject at the center of the frame. The area focused can be
As pictures are easily affected by camera shake, be sure that Vibration reduction
u Food
Use when taking pictures of food.
•
automatically zooms to the closest position at which it can
focus.
•
The closest possible shooting distance may vary according
to zoom position. The camera can focus at a closer distance
when F and the zoom indicator glow green and the zoom
indicator is positioned below I (wide-angle position). The
camera can focus on the subject as close as 7 cm (2.8 in.) at
the maximum wide-angle zoom position.
•
•
The flash does not fire and the flash mode is disabled.
Camera focuses on the subject at the center of the frame. The area focused can be
As pictures are easily affected by camera shake, be sure that Vibration reduction
Use the scene effect adjustment slider to adjust the influence lighting has on the color of
the camera’s memory even after the camera is turned off.
•
•
67
Shooting Suited to Scenes (Scene Mode)
l Museum
Use indoors where flash photography is prohibited (for
example, in museums and art galleries) or in other situations in
which you do not want to use the flash.
•
Camera focuses on the subject at the center of the frame.
The area focused can be changed by the touch shutter
•
•
•
shooting.
BSS is disabled and only one picture can be taken at a time when the shutter is released
As pictures are easily affected by camera shake, be sure that Vibration reduction
The flash does not fire and the flash mode is disabled.
•
•
m Fireworks show
O
Slow shutter speeds are used to capture the expanding burst
of light from a firework.
•
Camera focuses at infinity. The focus area or focus indicator
button is pressed halfway. Note, however, that objects in the
foreground may not always be in focus.
•
•
The flash does not fire and the flash mode is disabled.
n Copy
Provides clear pictures of text or drawings on a white board or
in print.
•
Camera focuses on the subject at the center of the frame.
The area focused can be changed by the touch shutter
•
•
•
Colored text and drawings may not show up well.
The default setting for flash mode is c Off.
Use of a tripod is recommended in scene modes with which O is indicated. Set Vibration
68
Shooting Suited to Scenes (Scene Mode)
o Backlighting
Use when light is coming from behind the subject, throwing
features or details into shadow. The flash fires automatically to
“fill in” (illuminate) shadows.
•
Camera focuses on the subject at the center of the frame.
The area focused can be changed by the touch shutter
•
•
The flash mode setting is fixed at X Fill flash.
p Panorama assist
Use when taking a series of pictures that will later be joined to form a single panorama using
information.
•
The default setting for flash mode is c Off.
69
Shooting Suited to Scenes (Scene Mode)
Shooting for a Panorama
The camera focuses on the subject at the center of the frame. Use a tripod for best
when using a tripod to stabilize the camera.
1
2
3
Tap the shooting mode icon in
shooting mode to display the
shooting mode selection menu, and
tap C.
Shooting mode
Scene
The scene mode selection screen is displayed.
Tap p Panorama assist.
Panorama assist
The panorama direction icons are displayed
to show the direction in which pictures will be
joined.
Tap a direction icon.
Select the direction in which picture will be
joined in the completed panorama; right (D),
left (C), up (A), or down (B).
T
A different direction can be selected by
tapping a different panorama direction icon.
W
36
first picture is taken in the next step.
4
Frame the first portion of the
panorama scene and take the
first picture.
One third of the picture will be
displayed as translucent.
T
W
36
70
Shooting Suited to Scenes (Scene Mode)
5
Take the next picture.
Frame the next picture so that one-
third of the frame overlaps the
previous picture.
Repeat this process until the
necessary number of pictures have
been taken to complete the scene.
35
6
Tap H when shooting is completed.
The camera returns to step 3.
32
B Notes on Panorama Assist
Shooting settings cannot be changed after the first picture is taken. Picture cannot be deleted, nor
can zoom be adjusted until the series is finalized.
• The panorama series is terminated if the camera enters standby mode with the auto off function
enabled to a longer setting is recommended.
D R Indicator
In Panorama assist scene mode, exposure, white
balance, and focus for all pictures in a panorama are
fixed at the values for the first picture in each series.
When the first picture is taken, R is displayed
to indicate that exposure, white balance, and focus are
locked.
35
D Panorama Maker 5
Install Panorama Maker 5 from the supplied ViewNX 2 CD-ROM.
single panorama.
D More Information
71
Shooting Smiling Faces (Smart Portrait Mode)
At the default settings, the camera uses face detection to detect human faces, and
then automatically releases the shutter when a smile is detected (smile timer). The
skin softening option can be used to smooth skin tones of human faces.
1
Tap the shooting mode icon in
shooting mode to display the
shooting mode selection menu, and
then tap F.
Shooting mode
Smart portrait
The camera enters smart portrait mode.
2
Frame a picture.
Point the camera at the subject.
When the camera detects a human face, a
yellow double border (focus area) is displayed
around that face. When focus is acquired on
that face, the double border will turn green
for a moment and focus is locked.
1/250 F3.6
Up to three faces can be detected. When the camera detects more than one face, the
double border is displayed around the face closest to the center of the frame, and single
borders around the others.
Tap the face framed by a single border to move the focus area to that face.
3
4
The shutter is automatically released.
If the camera detects that the face framed by the double border is smiling, Smile timer
Each time the shutter is released, the camera again initiates face detection and smile
detection operations for continuous automatic shooting.
Shooting ends.
To stop automatic shooting of smiling faces, either turn the camera off, set Smile timer
to Off, or tap the shooting mode icon and select another shooting mode.
72
Shooting Smiling Faces (Smart Portrait Mode)
B Notes on Smart Portrait Mode
• Digital zoom is not available.
• Self-timer is not available.
• Touch shutter cannot be enabled.
• Under some shooting conditions, the camera may be unable to detect faces or detect smiles.
B Notes on Skin Softening
• More time than usual may be required to save a picture when shooting with skin softening
function.
• In some shooting conditions, facial skin tones may not be smoothed or parts other than face may
be modified though the camera detects a face. If the desired results are not produced, set Skin
softening to Off and shoot again.
• The skin softening level cannot be adjusted when the portrait or night portrait is selected in the
scene mode.
• Retouch effects such as the glamour retouch function’s skin softening effect can be applied to
C Self-timer Lamp
The self-timer lamp blinks slowly when the smile timer is enabled and the camera detects a face, and
it blinks quickly immediately after the shutter is released.
C Releasing the Shutter Manually
Pictures can also be taken by pressing the shutter-release button. The camera focuses on the subject
at the center of the frame when faces are not detected.
C Auto Off in Smile Timer Mode
when either of the situations indicated below persists and no other operations are performed.
• The camera does not detect any faces.
• The camera detected a face, but cannot detect a smile.
D More Information
73
Shooting Smiling Faces (Smart Portrait Mode)
Changing the Smart Portrait Mode Settings
The settings indicated below can be made by tapping the tabs to display the
setting controls in smart portrait mode.
• Each icon also indicates the current setting.
• Tap the icon of the desired item to display the setting screen for that item.
• To hide the setting controls, tap the tab again.
T
T
W
W
36
1
2
3
4
5
6
T
T
OFF
ON
0.0
W
W
36
1
2
m Flash mode
A Image mode
Changes made to the image mode setting apply to all shooting modes (except
movie recording).
e Skin softening
3
Enable skin softening. When the shutter is released, the camera detects one or more
human faces (up to three), and processes the image to soften facial skin tones
before saving the picture.
The degree of skin softening applied can be selected from High, Normal (default
setting), and Low. When Off is selected, the skin softening function is disabled.
•
The effects of skin softening are not visible when framing pictures for shooting.
Check the degree of skin softening performed in playback mode.
74
Shooting Smiling Faces (Smart Portrait Mode)
4
y Blink proof
When On is selected, the camera
automatically releases the shutter twice
each time a picture is taken. Of the two
shots, one in which the subject’s eyes are
open is saved.
A blink was detected in the
picture just taken.
•
If the camera saved a picture in which
the subject’s eyes may have been
closed, the dialog shown at right is
displayed for a few seconds.
•
•
When On is selected, the flash is disabled.
The default setting is Off.
5
6
a Smile timer
•
On (default setting): The camera uses face detection to detect a human face, and
then automatically releases the shutter whenever a smile is detected.
Off: The camera does not release the shutter automatically with smile detection.
Press the shutter-release button to take a picture.
•
o Exposure compensation
C Settings in Smart Portrait Mode
There are functions with which this setting cannot be enabled. See “Camera Settings That cannot be
75
Camera Settings That cannot be Applied Simultaneously
Some shooting settings cannot be used with other functions.
Restricted function
Setting
Continuous
Description
When Continuous, BSS, or Multi-shot 16 is
selected, flash is disabled.
When Blink proof is set to On, flash is
disabled.
Subject tracking
When Touch shooting is set to Subject
tracking, Self-timer is disabled.
When Multi-shot 16 is selected, the Image
mode setting is fixed at L (image size:
2560×1920 pixels).
Continuous
When 3200 or 6400 is selected for ISO
sensitivity, the Image mode setting of only
M 2048×1536, N 1024×768, or O
640×480 can be selected. If any image mode
setting other than above is selected, the
image mode setting is automatically changed
to M 2048×1536 when ISO sensitivity is
set to 3200 or 6400.
Image mode
ISO sensitivity
Macro mode
Subject tracking
When Touch shooting is set to Subject
tracking, Macro mode is disabled.
When Multi-shot 16 is selected, the ISO
sensitivity setting is automatically specified
according to the brightness.
ISO sensitivity
Continuous
When taking a picture using the self-timer, the
continuous setting is fixed to Single.
When using the touch shutter function, one
picture is taken each time the monitor is
tapped.
Touch shutter
When taking a picture using Continuous,
BSS, or Multi-shot 16, Blink warning is
disabled.
Blink warning
Continuous
Continuous
When Continuous or BSS is selected for the
Continuous setting, date imprint is disabled.
Date imprint
When On is selected, Date imprint is
disabled.
76
Camera Settings That cannot be Applied Simultaneously
Restricted function
Setting
Continuous
Description
When Multi-shot 16 is selected, digital zoom
is not available.
Digital zoom
Subject tracking
When the touch shooting is set to Subject
tracking, digital zoom is disabled.
C Restricted Functions in Shooting Mode
the functions available in each shooting mode:
D More Information
77
More on Playback
Operations in Full-frame Playback Mode
Tap the playback icon (c) at the upper left
:
15 11 2010 15 30
0004. JPG
in the monitor in shooting mode to enter
playback mode and display pictures that
4/
4
The following operations are available in full-frame playback mode.
To
Tap
Description
A
Drag the picture to the right to display the
previous picture and to the left to display
the subsequent picture. Drag the picture
with two fingers to scroll ahead or back ten
pictures at a time.
Select a picture
–
Display 4, 9, or 16 picture thumbnails.
Picture thumbnails can be displayed by
placing two fingers on the picture currently
displayed and pinching them together.
View thumbnails
–
Enlarge view of picture currently displayed
in the monitor up to about 10×. Pictures
can be enlarged by placing two fingers on
the picture currently displayed and
spreading them apart. Tap H to return to
full-frame playback.
Zoom in
–
Tap R to play back the movie currently
displayed.
Play back movies
R
Set the picture rating/
play back pictures by
rating
Right tab Apply a rating of one to five to each
(P)
picture or play back pictures by rating.
Bottom
tab
Specify the playback settings and edit
pictures.
Make playback settings
Tap the playback mode icon to display the
Switch to another
playback mode
Playback playback mode selection menu and
mode icon change to favorite pictures, auto sort, or list
by date mode.
–
Tap the shooting mode icon displayed at
Shooting upper left in the monitor. The shutter-
mode icon release button can also be pressed to
switch to shooting mode.
Switch to shooting
mode
C Picture Orientation (Portrait or Landscape)
78
Viewing Multiple Pictures: Thumbnail Playback
pinching them together displays pictures in “contact sheets” of thumbnail images.
12
:
15 11 2010 15 30
0004. JPG
4/
4
The following operations can be performed while thumbnails are displayed.
To
Tap
Description
A
Increase number of picture thumbnails
displayed: 4 ➝ 9 ➝ 16
Placing two fingers on the picture
currently displayed and pinching them
together increases the number of picture
thumbnails displayed.
Increase number of picture
thumbnails displayed
–
–
Decrease number of picture thumbnails
displayed: 16 ➝ 9 ➝ 4
Decrease number of
picture thumbnails
displayed
Placing two fingers on the picture
currently displayed and spreading them
apart decreases the number of picture
thumbnails displayed.
–
Tap B or C, or drag the slider at the right
of the monitor. Dragging your finger up
and down on the monitor can also scroll
through the display.
Scroll display
–
B, C
Return to full-frame
playback
–
Tap a picture.
–
Set the picture rating/play Right tab Apply a rating of one to five to each
back pictures by rating
(P)
picture or play back pictures by rating.
Bottom The Delete, Slide show, Protect, or Print
Make playback settings
tab
set setting can be enabled.
Shooting
mode
icon
Tap the shooting mode icon or press the
shutter-release button.
Switch to shooting mode
–
79
Viewing Multiple Pictures: Thumbnail Playback
C Thumbnail Playback
Film frames
Mode Display
12
displayed with the icons shown at
right. Movies are displayed as film
frames.
Protect icon
Rating setting
icon
1
C Thumbnail Display in Favorite Pictures and Auto Sort Mode
• When thumbnails are displayed in favorite pictures
in the monitor.
4
• When thumbnails are displayed in auto sort mode
the monitor.
3
80
Taking a Closer Look: Playback Zoom
spreading them apart enlarges display of the current picture.
• The guide displayed in the bottom right of the monitor shows the portion of
the image currently displayed.
:
15 11 2010 15 30
0004. JPG
4/
×
3.0
The following operations can be performed while picture display is enlarged.
To
Tap
Description
A
Tap n to enlarge view of picture currently
displayed in monitor, up to about 10×.
Pictures can also be zoomed in by placing
two fingers on the picture currently
displayed and spreading them apart.
Zoom in
–
n
Tap o. When the magnification ratio
reaches 1×, the display returns to full-
frame playback mode. Pictures can also be
zoomed out by placing two fingers on the
picture currently displayed and pinching
them together.
Zoom out
–
–
o
Change the display
area
The area of the picture currently displayed
can be changed by dragging the picture.
–
Delete pictures
Tap E.
31
78
E
H
Switch to full-frame
playback
Tap H.
Create a cropped copy
(crop)
Crop the enlarged portion of the image
and save it as a separate file.
–
G
Switch to shooting
mode
–
Press the shutter-release button.
81
Taking a Closer Look: Playback Zoom
Pictures Taken with Face Detection Function
When zooming in (playback zoom) on a
picture taken with the face detection function
full-frame playback mode, the picture will be
enlarged with the face detected with
×
2.0
shooting at the center of the monitor (except
• If more than one face was detected, the picture will be enlarged with the face
on which focus was acquired at the center of the monitor. Tap M or N to
display other detected faces.
• When n or o is tapped to adjust the zoom ratio, the center of the picture
(normal playback zoom display), rather than the face, is displayed at the center
of the monitor.
82
Selecting Playback Mode
The following playback modes can be selected.
c
h
F
Playback mode
Play back all pictures.
Favorite pictures mode
Play back pictures added to albums.
Auto sort mode
Play back pictures and movies automatically sorted to the selected category
with shooting.
C
List by date mode
Play back pictures taken on the selected date.
1
Tap the playback mode icon in
playback mode.
:
15 11 2010 15 30
0004. JPG
The playback mode selection menu is
displayed.
4/
4
2
Tap the desired playback mode icon.
The camera enters the selected playback
mode.
Playback mode
Play
To return to the current playback mode, tap
the playback mode icon at the upper left in
the monitor.
83
Sorting Favorite Pictures (Favorite Pictures Mode)
Pictures can be sorted to albums. Once pictures have been sorted to albums,
favorite picture mode can be used to play back only the pictures in a specific
album. Adding pictures to albums makes finding a particular picture faster and
easier. Pictures can be sorted to albums categorized by themes such as travel or
weddings. A single picture can be added to multiple albums.
Adding Pictures to Albums
Pictures can be sorted by adding them to albums.
1
2
Select a desired picture and tap the
bottom tab.
:
15 11 2010 15 30
0004. JPG
Display the picture in full-frame playback
mode and tap the bottom tab.
4/
4
3
4
Tap h.
The favorite pictures screen is displayed.
Tap the desired album.
Favorite pictures
The picture is added to the selected album
and monitor display returns to full-frame
playback mode.
01
02
07
03
08
04
09
05
06
Repeat steps 1 and 2 to add a picture to
multiple albums.
84
Sorting Favorite Pictures (Favorite Pictures Mode)
B Notes on Adding Favorite Pictures
• An album can contain up to 200 pictures.
• Movies cannot be added to albums.
• If the selected picture has already been added to an album, the album icon turns yellow.
• When pictures are added to albums, they are not physically copied to albums or moved from the
D More Information
85
Sorting Favorite Pictures (Favorite Pictures Mode)
Viewing Pictures in an Album
Pictures can be displayed by selecting the album to which they were added in
“h favorite pictures mode“.
• In full-frame playback mode, just as with normal playback mode, picture display
can be enlarged, or pictures can be displayed as thumbnails. When the bottom
tab is tapped to display the setting controls, settings can be made and editing
1
Tap the playback mode icon in
playback mode to display the
playback mode selection menu
Playback mode
Favorite pictures
A list of albums is displayed.
2
Tap the desired album.
Favorite pictures
01
04
07
02
05
08
03
06
09
The picture in the selected album will be
displayed in full-frame playback mode.
:
15 11 2010 15 30
0004. JPG
The icon for the current album is displayed on
the screen.
Repeat steps 1 and 2 to select a different
album.
4/
4
86
Sorting Favorite Pictures (Favorite Pictures Mode)
Removing Pictures from Albums
To remove a picture from an album without permanently deleting it, follow the
procedures described below.
• Select the desired picture in full-frame
display in step 2 in favorite pictures mode
setting controls, and then tap h. The
confirmation dialog is displayed.
• Tap Yes to remove the picture from the
album. To exit without removing the
picture, tap No.
Remove this picture from
favorites?
No
Yes
B Note on Deleting Picture in Favorite Pictures Mode
Note that deleting a picture played back in favorite picture mode permanently deletes the original
87
Sorting Favorite Pictures (Favorite Pictures Mode)
Operations in Favorite Pictures Mode
The following operations are available with display of album list.
To
Tap
Description
A
Tap the bottom tab to display the setting
controls, and tap K.
Change the album icon
K
When the bottom tab is tapped to display
the setting controls, and c is tapped, the
album selection screen is displayed. Select
the desired album and tap I.
Delete all pictures in the
selected album
–
c
Switch to another
playback mode
Display the playback mode selection
menu.
–
m
Shooting Tap the shooting mode icon displayed at
mode upper left in the monitor or press the
Switch to shooting mode
icon
shutter-release button.
88
Sorting Favorite Pictures (Favorite Pictures Mode)
Changing Icons Assigned to Albums
The icon assigned to an album can be changed to reflect the theme of pictures
included in the album.
1
2
3
4
Tap the playback mode icon in
playback mode to display the
playback mode selection menu
Playback mode
Favorite pictures
Album list is displayed.
Tap the bottom tab to display the
setting controls and tap K.
Favorite pictures
01
04
07
02
05
03
06
Tap the desired album.
Choose icon
The album icon and icon color selection
screen is displayed.
01
04
07
02
05
08
03
06
09
Tap the desired icon to be assigned
to an album, tap or drag the slider to
select the icon’s color, and tap I.
Choose icon
01
0
0
02
03
The icon is changed and monitor display
returns to the display of album list.
To return to the album selection screen
without adjusting the settings, tap J.
B Notes on Icons for Albums
Choose icons for albums separately for the internal memory and for every memory card used.
• To change the icon for an album containing pictures stored in the internal memory, remove the
memory card from the camera.
• The default setting for icons are numbers.
89
Sorting Favorite Pictures (Favorite Pictures Mode)
C Adding/Viewing Favorite Pictures
When pictures are added to an album, they are not physically copied to the album or moved from
the folder to which they were originally recorded (A 171). Only the file names of pictures are added
to albums. In favorite pictures mode, pictures with file names that have been added to the specified
album are played back.
the original picture from the internal memory or memory card.
Adding Pictures to Albums
Internal memory/memory card
Album 1
0001.JPG
0003.JPG
0002.JPG
0004.JPG
0001.JPG
0002.JPG
0003.JPG
Adds file names
Album 2
Adds file names
0001.JPG
0004.JPG
Viewing Pictures in Albums
0001.JPG
Album 1
0002.JPG
0003.JPG
References
files
0001.JPG
0002.JPG
0003.JPG
Internal
memory/
memory card
Playback
90
Finding Pictures in Auto Sort Mode
When shooting pictures and movies, they are automatically sorted to one of the
categories shown below. If “F auto sort mode” is selected, pictures and movies
can be viewed by selecting the category to which they were sorted.
Z Smile
D Portraits
u Food
U Landscape
D Movie
V Dusk to dawn
X Retouched copies
D Close-ups
W Other scenes
• In full-frame playback mode, just as with normal playback mode, picture display
can be enlarged, pictures can be displayed as thumbnails, and movies can be
played back. When the bottom tab is tapped to display the setting controls,
settings can be made and editing can be performed on pictures sorted to the
Viewing Pictures in Auto Sort Mode
1
Tap the playback mode icon in
playback mode to display the
playback mode selection menu
Playback mode
Auto sort
Category list is displayed.
2
Tap the desired category.
Auto sort
For more information on categories, see “Auto
The picture in the selected category will be
displayed in full-frame playback mode.
:
15 11 2010 15 30
0004. JPG
The icon for the category currently selected is
displayed.
Repeat steps 1 and 2 to select a different
category.
4/
4
91
Finding Pictures in Auto Sort Mode
Auto Sort Mode Categories
Category
Description
setting set to On are displayed.
Z
Smile
Pictures taken in Portrait*, Night Portrait*, Party/indoor, and
D
Portraits
setting set to Off.
u
Food
U
Landscape
Pictures taken in Night landscape*, Sunset, Dusk/dawn, and
V
Dusk to dawn
Pictures taken in A (auto) mode with the macro mode setting
D
Close-ups
Movie
D
X
All other pictures that cannot be defined by the categories
described above.
W
Other scenes
B Notes on Auto Sort Mode
• Up to 999 pictures and movie files can be sorted to each category in auto sort mode. If 999
pictures or movies have already been sorted to a specific category, new pictures and movies
cannot be sorted to that category nor can they be displayed in auto sort mode. Display pictures
cannot be displayed in auto sort mode.
• Pictures or movies recorded by a camera other than the COOLPIX S80 cannot be displayed in auto
sort mode.
92
Finding Pictures in Auto Sort Mode
Operations in Auto Sort Mode
The following operations are available with display of category list.
To
Tap
Description
A
When the bottom tab is tapped to display
the setting controls, and c is tapped, the
category selection screen is displayed.
Select the desired category and tap I.
Delete all pictures in the
selected category
–
c
Switch to another
playback mode
Display the playback mode selection
menu.
–
F
Shooting Tap the shooting mode icon displayed at
mode the upper left in the monitor or press the
Switch to shooting mode
icon
shutter-release button.
93
Selecting Pictures Taken on a Specific Day (List by Date Mode)
In “C list by date mode“, pictures taken on a same date can be played back.
• In full-frame playback mode, just as with normal playback mode, picture display
can be enlarged, pictures can be displayed as thumbnails, and movies can be
played back. When the bottom tab is tapped to display the setting controls,
settings can be made and editing can be performed on pictures taken on a
Selecting a Date in List by Date Mode
1
Tap the playback mode icon in
playback mode to display the
playback mode selection menu
Playback mode
List by date
Dates for which pictures exist are listed.
2
Tap the desired date.
List by date
11/2010
Fri
Sun
Mon
Tue
Wed
Thu
Sat
To change the displayed month, tap C or D.
1
8
2
9
3
4
5
6
7
10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28 29 30
The first picture taken on the selected date
will be displayed full frame.
:
15 11 2010 15 30
0004. JPG
Repeat step 1 and 2 to select a different date.
4/
4
B Notes on List by Date Mode
• Up to 9,000 of the most recently recorded pictures can be displayed in list by date mode.
• Pictures taken before the date and time have been set are recognized as having been taken on
“01/01/2010.”
94
Selecting Pictures Taken on a Specific Day (List by Date Mode)
Operations in List by Date Mode
The following operations are available in the shooting date selection screen.
To
Tap
Description
A
Change the month
C, D Tap C or D.
–
–
When the bottom tab is tapped to display
the setting controls, and c is tapped, the
date selection screen is displayed. Select
the desired date and tap I.
Delete all pictures in the
selected date
c
Switch to another
playback mode
Display the playback mode selection
menu.
–
k
Shooting Tap the shooting mode icon displayed at
mode the upper left in the monitor or press the
Switch to shooting mode
icon
shutter-release button.
95
Playback Options
To adjust picture settings or edit pictures, tap the tab in full-frame playback mode
to display the setting controls.
• The controls available and monitor display vary depending upon the current
picture and camera settings.
• Tap the icon of the desired item to display the setting screen for that item.
• To hide the setting controls, tap the tab again.
:
15 11 2010 15 30
0004. JPG
5
4
3
2
1
0
1
4/
4
:
15 11 2010 15 30
0004. JPG
2
3
4
4/
4
9
8
7
6
5
1
2
5
6
7
h Add pictures to albums (except in
Remove pictures from albums (in
favorite pictures mode) ................... 87
8
3
4
9
* This function can also be performed in thumbnail playback mode. If the camera is switched
to thumbnail playback mode while pictures are played back in favorite pictures, auto sort,
or list by date mode, this function can be performed only on the pictures sorted to the
selected folder, category or date.
96
Setting the Picture Rating
A rating of one to five can be assigned to each picture. It is also possible to play
back only the pictures that have been assigned a specific rating.
1
Tap the right tab in full-frame
:
15 11 2010 15 30
0004. JPG
information.
4/
4
2
rating icon onto the picture.
Rating is applied.
Drag and drop another icon to change the
rating.
5
4
3
2
1
0
Drag and drop L to cancel the rating.
A picture’s rating can be confirmed by the
number of
mode.
shown in full-frame playback
Playing Back Pictures by Rating
1
Tap the right tab in full-frame
:
15 11 2010 15 30
0004. JPG
4/
4
2
Tap a rating icon to display the
pictures with that rating.
The icon of the tapped rating turns yellow,
and only the pictures assigned with the
selected rating are displayed. Multiple ratings
can be selected.
To stop displaying pictures of a selected
rating, tap the icon of the rating to deselect it.
To stop playback by rating, deselect all ratings.
5
4
3
2
1
0
B Notes on the Rating
• Each rating can be applied to a maximum of 999 pictures.
• Rating cannot be applied to movies.
• The ratings applied on the COOLPIX S80 are not recognized by your computer.
97
b Enjoying Slide Shows
Play back pictures, stored in the internal memory or on a memory card, one by one
in an automated “slide show.”
1
Tap the bottom tab in playback
mode to display the setting controls,
and tap b.
2
Tap Start.
Slide show
Effects
Start
To change the effects, tap Effects before
selecting Start, and select from Classic or
Zoom.
DEMO
Loop
To repeat the slide show automatically,
enable Loop by tapping Loop before
tapping Start. A check mark (w) will be
added to the loop option when enabled.
Tap l to play back sample images stored in the camera with an automatic loop
function.
To exit without playing back pictures in a slide show, tap J.
3
The slide show begins.
Tap the monitor to display the operation
panel at the bottom of the screen.
Tap the icons in the operation panel to
perform the corresponding operations. The
following operations are available.
To
Adjust volume
Rewind
Tap
X
O
P
Description
Adjust the volume of background music.
Tap and hold O to rewind slide show.
Tap and hold P to advance slide show.
Pause playback.
Advance
Pause
End
•
To resume playback, tap R displayed at the
center of the frame.
Q
S
End slide show.
98
d Protecting Important Pictures (Protect)
Protect selected pictures from accidental deletion. Protected pictures are
Protecting One Picture
1
2
3
Select the desired picture to be
protected in full-frame playback
mode, and tap the bottom tab.
:
15 11 2010 15 30
0004. JPG
4/
4
Tap d.
Tap On.
Protect
On
The selected picture is protected.
To exit without protecting pictures, tap J.
Off
B Note on Protecting Pictures
Note that formatting the camera’s internal memory or the memory card will permanently delete
100
d Protecting Important Pictures (Protect)
Protecting Multiple Pictures
Multiple pictures can be protected at a time.
1
Switch to thumbnail playback mode
display the setting controls, and
then tap d.
12
The monitor display switches to the picture
selection screen for protection.
2
Tap the desired pictures to be
protected.
Protect
When a picture is selected, a check mark is
displayed. To cancel the selection, tap the
picture again.
Tap n or o to change the number of
pictures displayed.
3
Tap I.
Protect
The selected pictures are protected.
To exit without protecting pictures, tap J.
Removing Protection from Pictures
• To remove protection from a picture, display a protected picture in full-frame
tap Off in step 3.
• To remove protection from multiple pictures at a time, uncheck protected
pictures in step 2 of “Protecting Multiple Pictures”.
101
a Creating a DPOF Print Order: Print Set
When printing pictures stored on the memory card using any of the following
methods, the Print set option in the playback menu is used to create digital “print
orders” for printing on DPOF-compatible devices.
• Taking the memory card to a digital photo lab
print order can also be created for pictures stored in the internal memory if the
memory card is removed from the camera
Creating a Print Order for One Picture
1
2
3
Select the desired picture in full-
frame playback mode and tap the
bottom tab.
:
15 11 2010 15 30
0004. JPG
4/
4
Tap a.
Tap the desired number of copies
and tap I.
Print set
1
2
7
3
8
4
9
5
0
To exit without making the print setting, tap
6
J.
If the total number of the pictures in a print
order, including pictures just added, exceeds
99, the screen shown at right will be
displayed.
Print set
Too many images selected.
Remove print marking from
other images?
-
Tap Yes to remove pictures previously
added from the print order and restrict the
print order to pictures just marked.
Yes
Cancel
-
Tap Cancel to remove the pictures just
added from the print order and restrict the
print order to pictures previously marked.
102
a Creating a DPOF Print Order: Print Set
4
Choose whether or not to print
shooting date and photo
information.
Print set
Date
Info
Tap Date to place w in the checkbox to
imprint the shooting date on the picture.
Tap Info to place w in the checkbox to
imprint the photo information (shutter speed
and aperture) on the picture.
Tap I to complete the print order.
Pictures selected for printing are recognized
by the w icon displayed with playback.
:
15 11 2010 15 30
0004. JPG
4/
4
103
a Creating a DPOF Print Order: Print Set
Creating a Print Order for Multiple Pictures
1
2
Switch to thumbnail playback mode
display the setting controls, and
then tap a.
12
The monitor display switches to the print set
screen.
Tap the desired pictures to print (up
to 99) and tap A or B at the upper
left in the monitor to specify the
number of copies (up to nine) for
each.
Print selection
1
×
×
1
1
Pictures selected for printing can be
recognized by the check mark (y) and the
numeral indicating the number of copies to be printed. Revert the number of copies to
[0] to cancel the selection of the picture.
Tap n or o to change the number of pictures displayed.
Tap n to remove print marking from all pictures and cancel the print order.
Tap I when setting is complete.
3
Choose whether or not to print
shooting date and photo
Print set
Date
information.
Info
Tap Date to place w in the checkbox to
imprint the shooting date on all pictures in
the print order.
Tap Info to place w in the checkbox to
imprint the photo information (shutter speed and aperture) on all pictures in the print
order.
Tap I to complete the print order.
104
a Creating a DPOF Print Order: Print Set
Canceling Print Order
• To remove a print marking from a picture, display a picture selected for printing
in full-frame playback mode, follow the procedure in “Creating a Print Order for
• To remove print markings from multiple pictures at a time, remove the print
markings of the desired pictures in step 2 of “Creating a Print Order for Multiple
B Notes on Printing with Shooting Date and Photo Information
When the Date and Info settings are enabled in the print set option, shooting date and photo
printing of shooting date and photo information is used.
• Photo information cannot be printed when the camera is connected directly to a printer, via the
• Note that Date and Info settings are reset when the print set option is displayed.
• The printed date is the one that has been set when a
picture is taken. Although the date is changed using
the Date option in the setup menu after a picture
has been taken, the printed date will not be
reflected.
B Note on Printing Pictures
1155..1111..22001100
When printing pictures taken at an Image mode
setting of p 3968×2232 (default setting), the edges of pictures may be cropped, preventing
D Date Imprint
When date and time of recording are imprinted on pictures using the Date imprint option
picture when they are taken. Pictures with the date imprinted on them can be printed from printers
that do not support printing of the date on pictures. Only the Date imprint date and time on
pictures will be printed, even if Print set is enabled with Date selected in the print set screen.
105
f Rotate Image
Specify the orientation in which recorded pictures are displayed with playback.
Still pictures can be rotated 90 degrees clockwise or 90 degrees counterclockwise.
Pictures that were recorded in portrait (“tall“) orientation can be rotated up to 180
degrees in either direction.
1
2
3
Select a picture in the full-frame
bottom tab to display the setting
controls, and tap M.
The retouch menu is displayed.
Tap f.
Retouch
Rotate image
The rotate image screen is displayed.
Tap J or I.
Rotate image
Rotate image
Rotate image
J
I
I
J
Rotate 90 degrees
clockwise
Rotate 90 degrees
counterclockwise
The picture rotates 90 degrees.
Tap I to finalize display orientation and save the orientation information with the
picture.
To exit without rotating image, tap J.
106
E Voice Memo: Recording and Playback
Use the camera’s built-in microphone to record voice memos for pictures.
Recording Voice Memos
1
2
3
Select a picture in the full-frame
bottom tab.
:
15 11 2010 15 30
0004. JPG
4/
4
Tap E.
The screen for recording voice memos is
displayed.
Tap W to record a voice memo.
Recording ends after 20 seconds.
Do not touch the built-in microphone during
recording.
To exit without recording voice memos, tap
J.
20s
During recording, o blinks in the monitor.
When S is tapped during recording,
recording ends.
When recording ends, the voice memo
playback screen is displayed. Follow the
instructions in step 3 of “Playing Voice
8s
D More Information
107
E Voice Memo: Recording and Playback
Playing Voice Memos
Pictures for which voice memos have been recorded are indicated with the p
1
2
3
Select a picture in the full-frame
bottom tab.
:
15 11 2010 15 30
0004. JPG
4/
4
Tap E.
The screen for playing back voice memos is
displayed.
Tap R to play the voice memo.
Tap S to stop playback.
Tap X to adjust playback volume.
To exit without playing voice memos, tap J.
20s
Deleting Voice Memos
Tap E in step 3 of “Playing Voice Memos.”
Tap Yes to delete only the voice memo.
File will be deleted. OK?
Yes
No
B Notes on Voice Memos
• When a picture with a voice memo attached is deleted, both the picture and its voice memo are
deleted.
• If a voice memo already exists for the current picture, it must be deleted before a new voice memo
can be recorded.
• The COOLPIX S80 is not able to record a voice memo for pictures taken with another make or
model of digital camera.
108
Editing Pictures
Editing Functions
Use the COOLPIX S80 to edit pictures in-camera and store them as separate files
Editing function
Description
Draw on pictures, or add decorations, to pictures.
Easily create retouched copies in which contrast and saturation
have been enhanced.
Create a copy of the current picture with enhanced brightness
and contrast, brightening dark portions of the picture.
Stretch the current picture horizontally to make the subject
appear thinner or wider.
Adjust the perspective of picture taken in landscape
orientation. Apply perspective control similar to that available
with shift lenses. This function is suited to pictures of buildings
or architecture.
Perspective control
Apply a variety of effects using digital filter. The available effects
are Color options, Soft, Selective color, Cross screen,
Fisheye, and Miniature effect.
Glamour retouch
Make facial skin tone softer and make faces look smaller with
larger eyes.
Create a small copy of pictures suitable for use as e-mail
attachments.
Crop a portion of the picture. Use to zoom in on a subject or
arrange a composition.
See page 106 for the rotate image function for more information.
B Notes on Picture Editing
• The editing functions of COOLPIX S80 cannot be used for pictures taken with another make or
model of digital camera.
• If no face is detected in a picture, a copy cannot be created using the glamour retouch function
• Edited copies created with COOLPIX S80 may not be displayed properly on another make or
model of digital camera. It may also be impossible to transfer them to a computer using another
make or model of digital camera.
• Editing functions are not available when there is not enough free space in the internal memory or
on the memory card to store the edited copies.
109
Editing Functions
C Restrictions on Picture Editing
When an edited copy is further modified with another editing function, check the following
restrictions.
Editing function used
Paint
Editing function to add
The paint, small picture, and crop functions can be added.
Quick retouch
D-Lighting
Stretch
Perspective control
Filter effects
The paint, small picture, glamour retouch, or crop function can be
added.
Glamour retouch
The editing functions other than glamour retouch can be added.
Another editing function cannot be added.
Small picture
No other editing functions can be added, except for the paint function,
which can be applied to cropped copies with an aspect ratio of 16:9
and those saved at an image size of 640 × 480 pixels or larger.
Crop
• Copies created with editing functions other than the paint function cannot be further edited with
the same function used to create them.
• When combining the small picture or crop function and another editing function, use the small
picture and crop functions after other editing functions have been applied.
• Retouch effects such as the glamour retouch function’s skin softening effect can be applied to
D Original and Edited Pictures
• Copies created with editing functions are not deleted if the original pictures are deleted. The
original pictures are not deleted if copies created with editing functions are deleted.
• Edited copies are stored with the same recording date and time as the original.
image are not applied to edited copies.
110
Picture Editing
U Paint
Draw on pictures or decorate them. Shooting date decoration can also be added.
Painted copies are stored as separate files.
1
Select a picture in full-frame
bottom tab to display the setting
controls, and tap U.
2 Use the I, J, K, and L tools to
Undo
paint pictures.
Pen
For more information about using each tool,
Tap n to display the picture in full-frame
playback mode and tap n again to enlarge
the picture display by 3×. Tap A, D, B, or
C to change the portion of the picture in the
monitor. To return to the original display size,
tap o.
Frame
Decoration
Eraser
Tap J to undo the last operation applied
using the pen, eraser, or decoration tool (up
to the last five operations can be undone).
Pen
3
Tap I.
Pen
111
Picture Editing
4
Tap Yes.
A new, painted copy is created.
Save OK?
Copies created with pictures taken at an
3968×2232 are saved at the image size of h
(1920 × 1080). Copies created with pictures
taken at an image mode setting of M
Yes
No
2048×1536 or larger are saved at the image size of g (2048 × 1536). Copies created
with pictures taken at an image mode setting of N 1024×768 and O 640×480 are
saved at the image size of l (640 × 480).
To exit without saving the copy, tap No.
Copies created with the paint function can be recognized by the d icon displayed in
playback mode.
Using the Paint Tools
Write and Draw on Pictures
Pen
Tap I to write or draw on pictures.
To change the pens’ color or weight, tap the
bottom tab to display the screen shown at right.
• Tap or drag the pen’s color slider to select pen’s
color.
Pen color
Pen thickness
• Tap the pen’s thickness slider to select pen’s
thickness.
Erase Paint Tool Additions
Eraser
Tap J to erase additions to pictures using the
paint or decoration tool.
To change the eraser’s size, tap the bottom tab to
display the screen shown at right.
Eraser size
• Tap the slider of the eraser’s size to select the size
of the eraser.
112
Picture Editing
Decoration type
Add Decorations
Tap K to add a decoration.
Decoration
To change the decoration type or size, tap the
bottom tab to display the screen shown at right.
• Decoration type can be selected from 14 types.
• Tap the decoration size slider to select the
decoration size. When f is selected for the
decoration type, f (day, month, year) and S
(day, month, year, time) options are available.
Decoration size
Add a Frame
Frame
Tap L to add a frame around the picture.
• Tap C or D to display seven different frames
one at a time. Tap I to select a frame.
B Notes on Shooting Date Decoration
of O 640×480, the shooting date may be difficult to read. Set the Image mode setting of N
1024×768 or larger.
• The date added with the shooting date decoration uses the format selected in the setup menu’s
• The date added with the shooting date decoration is the date on which the picture was taken. The
date added with the shooting date decoration cannot be changed.
D More Information
113
Picture Editing
k Quick Retouch: Enhancing Contrast and Saturation
Quick retouch can be used to easily create retouched copies in which contrast and
saturation have been enhanced. Copies created with the quick retouch function
are stored as separate files.
1
2
3
4
Select a picture in full-frame
bottom tab to display the setting
controls, and tap M.
The retouch menu is displayed.
Tap k.
Retouch
Quick retouch
The screen for selecting the degree of
enhancement is displayed.
Choose the degree of enhancement
performed and tap I.
Quick retouch
Tap Yes.
A new, retouched copy is created (it may take
several seconds to create the copy).
Save OK?
To exit without saving the copy, tap No.
Copies created with the quick retouch
function can be recognized by the s icon
displayed in playback mode.
Yes
No
D More Information
114
Picture Editing
I D-Lighting: Enhancing Brightness and Contrast
D-Lighting can be used to create copies with enhanced brightness and contrast,
brightening dark portions of a picture. Enhanced copies are stored as separate
files.
1
2
3
4
Select a picture in full-frame
bottom tab to display the setting
controls, and tap M.
The retouch menu is displayed.
Tap I.
Retouch
D-Lighting
The original version will be shown on the left
and the edited version will be shown on the
right.
Tap I.
D-Lighting
Tap Yes.
A new, edited copy is created.
To exit without saving the copy, tap No.
Save OK?
Copies created with the D-Lighting function can
be recognized by the c icon displayed in
playback mode.
Yes
No
D More Information
115
Picture Editing
P Stretch: Stretching Pictures
Stretch pictures horizontally. Stretched copies are stored as separate files.
1
2
3
4
5
Select a picture in full-frame
bottom tab to display the setting
controls, and tap M.
The retouch menu is displayed.
Tap P.
Retouch
Stretch
Stretch
Stretch
Tap or drag the slider to adjust
stretch effects.
Tap I.
Tap Yes.
A new, edited copy is created.
To exit without saving the copy, tap No.
Save OK?
Copies created with the stretch function can
be recognized by the r icon displayed in
playback mode.
Yes
No
D More Information
116
Picture Editing
O Perspective Control: Adjust a Sense of Perspective
Adjust the sense of perspective in the picture taken in landscape orientation.
Copies created with the perspective control function are stored as separate files.
1
2
3
4
5
Select a picture in full-frame
bottom tab to display the setting
controls, and tap M.
The retouch menu is displayed.
Tap O.
Retouch
Perspective control
Tap or drag the slider to adjust
perspective control.
Perspective control
Tap I.
Perspective control
Tap Yes.
A new, edited copy is created.
To exit without saving the copy, tap No.
Copies created with the perspective control
function can be recognized by the q icon
displayed in playback mode.
Save OK?
Yes
No
D More Information
117
Picture Editing
i Filter Effects (digital filter)
Filter effects (digital filter) can be used to apply a variety of effects to pictures. The
available effects are Color options, Soft, Selective color, Cross screen,
Fisheye, and Miniature effect. New copies are stored as separate files.
1
2
3
Select a picture in full-frame
bottom tab to display the setting
controls, and tap M.
The retouch menu is displayed.
Tap i.
Retouch
Filter effects
Tap C or D to select the type of
the effects.
Color options
Type
Description
Modify color tones.
Color options
•
Select the option from o
(vivid color), p (black-and
white), q (sepia), or r
(cyanotype), and tap I.
Color
options
118
Picture Editing
Type
Description
Give the picture a soft look by
blurring the area surrounding
the point that is tapped.
Soft
•
Tap the monitor, select the
degree of effects, and tap
I.
Soft
Keep one specified color in the picture, and change the other colors to
black and white.
Selective
color
•
Tap the color slider displayed on the screen to select the color to
keep, and tap I.
Produce star-like rays of light that radiate outward from bright objects
such as sunlight reflections or city lights. This effect is suitable for night
scenes.
Cross
screen
•
Confirm the degree of enhancement, and tap I.
Make a picture look as if it were taken with a fisheye lens. This effect is
well-suited for pictures taken in macro mode.
Fisheye
•
Confirm the degree of enhancement, and tap I.
Make a picture look like a miniature scene taken in macro mode. This
effect is well-suited for pictures taken from a high vantage point with
the main subject at the center of the picture.
Miniature
effect
•
Confirm the degree of enhancement, and tap I.
A confirmation screen for saving the edited copy is displayed.
Tap J to return to the retouch menu without making any changes.
4
Tap Yes in the confirmation dialog.
A new, edited copy is created.
Save OK?
To exit without saving the copy, tap No.
Copies created using the filter effects function
can be recognized by the i icon displayed in
playback mode.
No
Yes
D More Information
119
Picture Editing
j Glamour Retouch
Glamour retouch can be used to soften the skin tone of faces detected in a picture
and make the faces look smaller with larger eyes. New copies are stored as
separate files.
1
2
3
4
Select a picture in full-frame
bottom tab to display the setting
controls, and tap M.
The retouch menu is displayed.
Tap j.
Retouch
Glamour retouch
Tap e (skin softening) or k (both).
e: Soften facial skin tones
Glamour retouch
k: Soften facial skin tones, make faces look
smaller, and make eyes look larger.
The preview screen is displayed.
Preview the result of the effects.
Preview
Skin tones in up to 12 faces, in the order of
that closest to the center of the frame, are
softened.
Tap Before or After to view the picture with
or without the effects.
Before
After
If more than one face was softened, tap M or
N to display a different face.
To change the effects, tap J to return to step 3.
Tap I to display the confirmation dialog for saving the new copy.
120
Picture Editing
5
Tap Yes.
A new, edited copy is created.
To exit without saving the copy, tap No.
Save OK?
Copies created using the glamour retouch
function can be recognized by the j icon
displayed in playback mode.
Yes
No
B Notes on Glamour Retouch
• The glamour retouch function cannot be performed when no face is detected in the picture.
• The glamour retouch function may not perform as expected depending on the direction in which
the faces are looking or the brightness of the faces in the picture.
D More Information
121
Picture Editing
g Small Picture: Making Smaller Pictures
Create a small copy of the current picture. This feature is useful for creating copies
for display on Web pages or e-mail attachments.
• The size of the small copy for pictures taken at an image mode setting of p
3968×2232 is h (1920 × 1080). For pictures taken at other sizes, the options of
l 640×480, m 320×240, and n 160×120 are available.
• Small copies are saved as separate files with a compression ratio of 1:16.
1
2
3
4
Select a picture in full-frame
bottom tab to display the setting
controls, and tap M.
The retouch menu is displayed.
Tap g.
Retouch
Small picture
Tap the desired small copy size icon
and tap I.
Small picture
×
320 240
Small picture size cannot be selected for
pictures taken at an image mode setting of p
3968×2232. Tap I.
Tap Yes.
A new, small copy is created.
To exit without saving the copy, tap No.
The copy is displayed with a gray frame.
Create small picture file?
No
Yes
D More Information
122
Picture Editing
o Crop: Creating a Cropped Copy
Create a copy containing only the portion visible in the monitor when G is displayed
1
Portrait-oriented (“tall”) pictures taken at an image mode setting of p 3968×2232 must
If portrait-oriented (“tall”) pictures taken at an image mode setting other than p
3968×2232 are enlarged and cropped in portrait orientation, the cropped images will
be in landscape orientation. To create a portrait-oriented (“tall”) cropped copy, rotate the
2
Refine copy composition.
Tap n or o to adjust the zoom ratio.
Drag the picture so that only the portion to be
cropped is visible in the monitor.
×
2.0
3
4
Tap G.
When G is not displayed, adjust the zoom
ratio so that G is displayed.
Pictures taken at an image mode setting of p
3968×2232 can be cropped when the zoom
ratio is 2.0× or less.
Portrait-oriented (“tall”) pictures taken at image
×
2.0
mode settings other than p 3968×2232
cannot be cropped if the zoom ratio is too low.
Tap Yes.
A cropped copy is created.
To exit without saving the copy, tap No.
Save this image as
displayed?
Copies created using the crop function can be
recognized by the icon displayed in
a
playback mode.
Yes
No
C Image Size
•
When pictures taken at an image mode setting of p 3968×2232 are cropped, the size of the
cropped copies is h (1920 × 1080 pixels) and the aspect ratio is 16:9.
When pictures taken at image mode settings other than p 3968×2232 are cropped, the aspect
ratio of the cropped copies is 4:3. As the area to be saved is reduced, the image size (pixels) of the
cropped copy is also reduced.
When the size of the cropped copy is 320 × 240 or 160 × 120, a gray frame is displayed around the
picture, and the small picture icon m is displayed on the top of the screen in full-frame playback mode.
•
•
D More Information
123
Movie Recording and Playback
Recording Movies
Record high-definition movies with sound recorded via the built-in microphone.
• The maximum recording time for a single movie is 29 minutes, even when there
1
2
Tap the shooting mode icon in
shooting mode to display the
shooting mode selection menu and
then tap D.
Shooting mode
Movie
Press the shutter-release
button all the way down to
start recording.
The camera focuses on the subject at
center of the frame.
T
W
6s
A progress bar shows the amount of
recording time remaining.
To end recording, press the shutter-release button all the way down again.
Movie recording can also be initiated or stopped by tapping the monitor.
Recording stops automatically when the maximum movie length that can be recorded
has run out.
124
Recording Movies
B Recording Movies
• Memory cards with an SD Speed Class rating of 6 or faster are recommended when recording
Speed Class ratings are used.
• The camera focuses when the shutter-release button is pressed halfway, and the focus remains
locked while the shutter-release button is pressed halfway. Focus is locked while recording.
• Digital zoom deteriorates picture quality. When recording movies, the digital zoom can magnify
the image up to 2× the maximum optical zoom ratio.
• In some cases, movie recordings may capture the sounds of the camera, such as the sound of the
lens movement when zooming, the vibration reduction function, or the aperture control when
the brightness changes.
Avoiding bright objects such as the sun, reflections of the sun, and electric lights when recording
movies is recommended.
• When recording or playing back movies, colored stripes (interference patterns or moiré) may
appear on subjects that have a regular, repeating grid, such as pattern of weave in cloths or
windows in a building, depending on the shooting distance or zoom ratio. This phenomenon
occurs when the subject’s pattern interferes with the camera sensor grid, and it does not indicate
a malfunction.
B Note on Saving Movies
After a movie has been recorded, it is not fully saved to the internal memory or memory card until
monitor display returns to the shooting display. Do not open the battery-chamber/memory card
slot cover before movies have been fully saved. Removing the memory card while movies are being
saved could result in loss of data or in damage to the camera or card.
125
Recording Movies
Movie Recording Settings
During movie recording, the settings indicated below can be made by tapping the
tabs to display the settings controls.
• Each icon also indicates the current setting.
• Tap the icon of the desired item to display the setting screen for that item.
• To hide the setting controls, tap the tab again.
T
T
W
W
OFF
18s
1
2
3
T
T
W
W
ON
18s
1
2
3
p Macro mode
A Movie options
q Touch shooting
126
Recording Movies
A Movie Options
Select the desired movie option to record. Larger image sizes and faster movie
bitrates mean greater image quality and larger movie file sizes.
Option
Description
Movies with an aspect ratio of 16:9 are recorded in high
definition. This option is suited to playback on a wide screen
TV.
N HD 720p (1280×720)
(default setting)
•
Image size: 1280 × 720 pixels
Movie bitrate: 9 Mbps
•
Movies with an aspect ratio of 4:3 are recorded.
y VGA (640×480)
•
Image size: 640 × 480 pixels
Movie bitrate: 3 Mbps
•
Movies with an aspect ratio of 4:3 are recorded.
z QVGA (320×240)
•
•
Image size: 320 × 240 pixels
Movie bitrate: 640 kbps
• The movie bitrate is the volume of movie data recorded per second. As a
variable bitrate (VBR) system has been adopted, the movie recording rate varies
automatically according to the subject so that more data is recorded per
second for movies containing frequently moving subjects, thus increasing
movie file size.
• The frame rate is approximately 30 frames per second in any options.
C Movie Options and Maximum Movie Length
Option
Internal memory (approx. 79 MB)
Memory card (4 GB)*
55 min
N HD 720p (1280×720)
y VGA (640×480)
z QVGA (320×240)
1 min 4 s
3 min
2 h 40 min
8 min 26 s
10 h 10 min
All figures are approximate. The maximum recording time may vary by make of memory card and
the bitrates at which the movie was recorded.
* The maximum recording time for a single movie is 29 minutes. The maximum movie length
displayed during recording is 29 minutes, even when there is enough free space on the
memory card for a longer movie.
D More Information
127
Movie Playback
are recognized by R icon. Tap R to play a
movie.
:
15 11 2010 15 30
0005.MOV
• To adjust the volume before playback, tap
the bottom tab to display the setting
controls and tap i.
18s
Tap the monitor during playback to display
the control panel at the bottom of the monitor. The operations described below
are available by tapping the icons in the panel.
During playback
12s
To
Tap
Description
Tap X to adjust the volume.
Adjust
volume
X
Rewind
Touch and hold O to rewind movie.
O
P
Advance
Touch and hold P to advance movie.
Pause playback.
The following operations can be performed while playback is paused.
Rewind movie back one frame. Touch and hold U for
continuous frame-by-frame rewind.
U
Pause
End
Q
S
Advance movie forward one frame. Touch and hold V for
continuous frame-by-frame advance.
V
Tap R at the center of the monitor to resume playback.
R
End playback and return to full-frame display.
B Note on Movie Playback
Movies recorded by a camera other than the COOLPIX S80 cannot be played back.
C Deleting Movie Files
128
Connecting to Televisions, Computers and Printers
Connecting to a TV
Connect the camera to a television to play back pictures or movies on the
television. If your TV is equipped with an HDMI port, pictures can be displayed in
high definition when an HDMI cable (commercially available) is used to connect
the camera to the TV.
1
Close the slide cover to turn off the camera.
2
Connect the camera to the TV.
When using the supplied audio/video cable
Connect the yellow plug to the video-in jack and the white and red plugs to the stereo
audio-in jacks on the TV.
Yellow White Red
When using a commercially available HDMI cable
Connect the plug to the HDMI jack on the TV.
HDMI mini connector (Type C)
to HDMI jack
129
Connecting to a TV
3
4
Tune the television to the video channel.
See the documentation provided with your television for details.
Open the slide cover to turn on the camera.
Pictures are displayed on the television and the camera
monitor turns off.
information.
130
Connecting to a TV
Operations with TV Connection
While pictures are displayed full-frame on the TV, the previous or subsequent
picture can be viewed by dragging your finger across the camera monitor.
Drag the picture with two fingers to scroll ahead or back ten pictures at a time.
playback mode on the camera.
When the first frame of a movie is displayed, the movie can be played back by
holding your finger on the camera monitor and removing it after about one
second.
• Tap the camera monitor to turn TV display off and display the picture in the
camera monitor. When pictures are displayed in the camera monitor, tap the
controls displayed to operate the camera (only during playback mode).
• Pictures will be automatically displayed on the TV in the following situations.
-
-
-
No operations are performed for a few seconds in playback mode.
A slide show is played back.
A movie is played back.
B Notes on Connecting the HDMI Cable
• HDMI cable is not provided. Use a commercially available HDMI cable to connect the camera to a
high-definition TV. The output terminal on this camera is an HDMI mini connector (type C). When
purchasing an HDMI cable, be sure that the device end of the cable is an HDMI mini connector.
setting of N HD 720p (1280 × 720) are recommended for pictures or movies that will be played
back on a TV via HDMI connection.
B Connecting the Cable
When connecting the cable, be sure that the camera connector is properly oriented. Do not use
force when connecting the cable. When disconnecting the cable, do not pull the connector at an
angle.
• Do not connect the HDMI cable and audio/video cable to the camera simultaneously.
• Do not connect the HDMI cable and USB cable to the camera simultaneously.
B Video Mode
Be sure that the camera’s video mode setting conforms to the standard used by your television.
131
Connecting to a Computer
Use the supplied USB cable to connect the camera to a computer and copy
(transfer) images to the computer.
Before Connecting the Camera
Install the Software
Use the supplied ViewNX 2 CD and install the following software on the computer.
• ViewNX 2: Use the image transfer feature “Nikon Transfer 2” to save images that
were captured with the camera on the computer. Saved images can be viewed
and printed. Image and movie editing features are also supported.
• Panorama Maker 5: This software can join a series of images to create a single
panorama image.
For more information on installing the software, refer to the Quick Start Guide.
Compatible Operating Systems
Windows
Windows 7 Home Basic/Home Premium/Professional/Enterprise/Ultimate,
Windows Vista Home Basic/Home Premium/Business/Enterprise/Ultimate (Service
Pack 2), or Windows XP Home Edition/Professional (Service Pack 3)
Macintosh
Mac OS X (version 10.4.11, 10.5.8, 10.6.4)
For information on the requirements for playing back high-definition movies, refer
Refer to the Nikon website for the latest information on operating system
compatibility.
B Note on Computer Connection
Disconnect other USB devices such as commercial USB chargers from the computer. Simultaneous
connection of the camera and other USB devices to the computer could result in operation
malfunction or excessive supply of power to the camera, causing damage to the camera or memory
card. Refer to the documentation supplied with other USB devices for more information.
132
Connecting to a Computer
B Notes on Power Source
• When connecting the camera to a computer to transfer images, use a fully charged battery to
prevent the camera from turning off unexpectedly.
• When the camera is connected to a computer via the supplied USB cable with Auto (default
setting) selected for the Charge by computer option in the setup menu, the battery inserted into
from an electrical outlet. Do not use any other make or model of AC adapter as they may cause the
camera to overheat or malfunction.
Transferring Images from a Camera to a Computer
1
2
3
Start the computer to which ViewNX 2 was installed.
Be sure that the camera is off.
Connect the camera to the computer using the supplied USB cable.
Be sure that connectors are properly oriented. Do not attempt to insert connectors at an
angle, and do not use force when connecting or disconnecting the USB cable.
The camera is automatically turned on and the power-
on lamp will light or blink. The camera monitor will
remain off.
B Connecting the USB Cable
The connection may not be recognized if the camera is connected to the computer via a USB hub.
133
Connecting to a Computer
4
Start the ViewNX 2 image transfer feature “Nikon Transfer 2” installed
on the computer.
•
Windows 7
When the Devices and Printers K S80 screen is displayed, click Change program
under Import pictures and videos. Select Import File using Nikon Transfer 2 in
the Change program dialog and click OK.
Double-click Import File on the Devices and Printers K S80 screen.
•
•
Windows Vista
When the AutoPlay dialog is displayed, click Import File using Nikon Transfer 2.
Windows XP
When the action selection dialog is displayed, select Nikon Transfer 2 Import File,
and click OK.
•
Mac OS X
Nikon Transfer 2 will start automatically when the camera is connected to the
computer if Yes was selected in the Auto-Launch setting dialog when Nikon
Transfer 2 was first installed.
•
•
If charge for the battery inserted into the camera is low, the computer may not
recognize the camera. If the camera is not recognized, images will not be transferred.
When battery charging starts automatically using power supplied by the computer,
wait until battery charge has reached a sufficient level to begin transfer.
If there are a large number of images on the memory card, it may take some time for
Nikon Transfer 2 to start.
5
Confirm that the source device is displayed in the transfer options
Source panel and click Start Transfer.
Source device
Start Transfer button
Any images that have not been transferred to the computer will be transferred (default
setting of ViewNX 2).
134
Connecting to a Computer
ViewNX 2 starts automatically when the transfer is complete (default setting of ViewNX
2). Transferred images can be viewed.
For more information on using ViewNX 2, refer to the ViewNX 2 help information
Disconnecting the Camera
Do not turn off the camera or disconnect the camera from the computer during
transfer.
When transfer is complete, open the slide cover and close it again to turn off the
camera, and disconnect the USB cable.
The camera turns off automatically if there is no communication with the
computer for 30 minutes while the camera is connected via the USB cable.
B Charging the Battery
The power on lamp slowly blinks orange while the battery inserted into the camera is charging (A 137).
135
Connecting to a Computer
C Transferring Images Using a Computer’s Card Slot or a Commercially-
available Card Reader
When the memory card is inserted into a computer’s card slot or into a commercially-available card
reader, the images can be transferred using “Nikon Transfer 2”, the image transfer feature of ViewNX 2.
• Make sure that the memory card being used is supported by the card reader or other card reading
device.
• To transfer images, insert the memory card into the card reader or card slot and follow the
• To transfer images saved in the camera’s internal memory, the images must first be copied to a
D Starting ViewNX 2 or Nikon Transfer 2 Manually
Windows
Choose Start menu > All Programs > ViewNX 2 > ViewNX 2.
Double-clicking the ViewNX 2 shortcut icon on the desktop will also start ViewNX 2.
Mac OS X
Open the Applications folder, open the Nikon Software > ViewNX 2 folders in that order, and
then double-click the ViewNX 2 icon. Clicking the ViewNX 2 icon on the Dock will also start
ViewNX 2.
Click Transfer in the ViewNX 2 screen to start Nikon Transfer 2.
D Viewing ViewNX 2 Help Information
For more information on ViewNX 2 or Nikon Transfer 2, start ViewNX 2 or Nikon Transfer 2 and select
ViewNX 2 Help from the Help menu.
D Panorama Creation with Panorama Maker 5
panorama photo with Panorama Maker 5.
• Panorama Maker 5 can be installed on a computer using the supplied ViewNX 2 CD.
• After installation is complete, follow the procedure described below to start Panorama Maker 5.
Windows
Choose Start menu>All Programs>ArcSoft Panorama Maker 5>Panorama Maker 5.
Mac OS X
Open Applications and double-click the Panorama Maker 5 icon.
• For more information on using Panorama Maker 5, refer to the on-screen instructions and help
information contained in Panorama Maker 5.
D Image File Names and Folder Names
136
Connecting to a Computer
Charging While Connecting to a Computer
set to Auto (default setting), if the camera is connected to a computer using the
USB cable, the battery inserted into the camera can be automatically charged
depending on the ability of the computer to supply power.
to a computer.
Power-on Lamp
The following chart explains power-on lamp status when the camera is connected
to a computer.
Power-on lamp
Description
Blinks slowly
(orange)
Battery charging.
Battery not charging. Charging is complete when the power-on lamp
stops blinking orange and glows green.
Glows (green)
•
The ambient temperature is not suited to charging. Charge the battery
indoors with an ambient temperature of 5 °C to 35 °C (41 °F to 95 °F).
A USB cable is not correctly connected or the battery is faulty.
Reconnect the USB cable correctly or replace the battery.
Computer is in sleep mode and does not supply power. Reboot a computer.
The battery cannot be charged as computer’s specifications or
settings does not support power supply to the camera.
•
Flickers (orange)
•
•
B Notes on Charging with Connection to a Computer
•
The battery cannot be charged, nor can data be transferred, when the camera is connected to a
camera’s clock battery ( 149) has been exhausted, the date and time must be reset before the battery
can be charged or images can be transferred with connection to a computer. In this case, use the
• If the camera is turned off by opening and closing the slide cover, charging will also stop.
• If a computer enters sleep mode while charging, charging will stop and the camera may be turned off.
• When disconnecting the camera from a computer, turn the camera off by opening and closing the
slide cover and then disconnect the USB cable.
• About 3 hours are required to charge a fully exhausted battery. Charging time increases when
images are transferred while the battery is charging.
• When the camera is connected to a computer, an application installed on the computer, such as
Nikon Transfer 2, may start. If the camera was connected to the computer for the sole purpose of
charging the battery, exit the application.
• The camera turns off automatically if there is no communication with the computer for 30 minutes
after the battery has finished charging.
• Depending upon computer specifications, settings, and power supply and allocation, it may be
impossible to charge the battery inserted into the camera via computer connection.
137
Connecting to a Printer
to the printer and print pictures without using a computer.
Follow the procedures below to print pictures.
Take pictures
Select pictures for printing and number
of copies using Print set option
Print pictures one at a
When printing is complete, turn camera off and disconnect the USB cable
B Notes on Power Source
• When connecting the camera to a printer, use a fully charged battery to prevent the camera from
turning off unexpectedly.
• If the AC Adapter EH-62D (available separately) is used, COOLPIX S80 can be powered from a
home electrical outlet. Do not use any other AC adapters as it will cause the camera to heat up or
malfunction.
B Note on Printing Pictures
When printing pictures taken at an Image mode setting of p 3968×2232 (default setting), the
edges of pictures may be cropped, preventing printing of complete pictures.
It may be possible to print complete pictures if settings on the printer are applied so that borders are
printed around pictures (borderless printing not enabled).
Refer to the documentation supplied with the printer or consult the digital photo lab for further
details to make sure that the printer supports printing at an aspect ratio of 16:9.
D Printing Pictures
In addition to printing pictures transferred to a computer from your personal printer and printing
over a direct camera-to-printer connection, the following options are also available for printing
pictures stored on the memory card:
• Insert a memory card into a DPOF-compatible printer’s card slot
• Take a memory card to a digital photo lab
select the pictures, and the desired number of prints each, from those recorded to a memory card.
138
Connecting to a Printer
Connecting the Camera to a Printer
1
Close the slide cover to turn off the camera.
2
3
Turn on the printer.
Check printer settings.
Connect the camera to the printer using the supplied USB cable.
4
The camera is automatically turned on.
When properly connected, the PictBridge startup
screen ( ) will be displayed in the camera monitor,
1
followed by the print selection screen ( ).
2
Print selection
15/11/2010 12/ 12
1
2
139
Connecting to a Printer
B Notes on Connecting/Disconnecting Cable
• Be sure that connectors are properly oriented. Do not attempt to insert connectors at an angle,
and do not use force when connecting or disconnecting the USB cable.
• Open and close the slide cover to turn off the camera before disconnecting the USB cable.
B If the PictBridge Startup Screen is not Displayed
in the camera’s setup menu to Off and reconnect the cable again.
140
Connecting to a Printer
Printing Pictures One at a Time
procedures described below to print a picture.
1
2
3
4
5
Tap C or D to choose the desired
picture, and tap I.
Print selection
15/11/2010 12/ 12
Previous or subsequent picture can also be
viewed by tapping the scroll bar.
Tap o to display 12 thumbnails, and n to
switch back to full-frame playback.
Tap Copies.
PictBridge
Start print
Copies
Paper size
Tap the desired number of copies
(up to nine).
Copies
1
4
7
2
5
8
3
6
9
Tap Paper size.
PictBridge
Start print
Copies
Paper size
Tap the desired paper size.
1/2
Paper size
Default
Tap A or B to display additional options.
To specify paper size using settings on the
printer, tap Default in the paper size option.
3.5×5 in.
5×7 in.
100×150 mm
141
Connecting to a Printer
6
Tap Start print.
PictBridge
Start print
Copies
Paper size
7
Printing begins.
Current number of copies/
total number of copies
Monitor display returns to the print selection
screen shown in step 1 when printing is
complete.
To cancel printing before all copies have been
printed, tap Cancel.
Printing
002/004
Cancel
Printing Multiple Pictures
procedures described below to print multiple pictures.
1 When the print selection screen is
Print selection
15/11/2010
12/ 12
displayed, tap F.
The print menu is displayed.
2
Tap Paper size.
Print menu
To exit the print menu, tap J.
Print selection
Print all images
DPOF printing
Paper size
142
Connecting to a Printer
3
4
Tap the desired paper size.
1/2
Paper size
Tap A or B to display additional options.
Default
3.5×5 in.
To specify paper size using settings on the
printer, tap Default in the paper size option.
5×7 in.
100×150 mm
Tap Print selection, Print all
images or DPOF printing.
Print menu
Print selection
Print all images
DPOF printing
Paper size
Print selection
Choose pictures (up to 99) and the
number of copies (up to nine) of
each.
Print selection
15/11/2010
12/ 20
1
×1
×1
×
1
1
•
Tap the desired pictures and tap
A or B at the upper left in the
monitor to specify the number of
copies to be printed.
×1
×
•
Pictures selected for printing can
be recognized by the check mark
(w) and the numeral indicating the number of copies to be printed. Revert
the number of copies to [0] to cancel the selection of the picture.
Tap n to switch back to full-frame playback, and o to display 9 thumbnails.
Tap n to remove print marking from all pictures.
•
•
•
•
Tap I when setting is complete.
When the screen shown at right is
displayed, tap Start print to print.
Print selection
005 prints
•
To return to the print menu, tap
Cancel.
Start print
Cancel
143
Connecting to a Printer
Print all images
One copy each of all pictures stored
Print all images
in the internal memory, or on the
memory card, is printed.
005 prints
•
When the screen shown at right is
displayed, tap Start print to print.
To return to the print menu, tap
Cancel.
Start print
•
Cancel
DPOF printing
Print pictures for which a print order
DPOF printing
020 prints
was created using the Print set
•
When the screen shown at right is
displayed, tap Start print to print.
To return to the print menu, tap
J.
Start print
View images
•
To view the current print order,
tap View images. To print
pictures, tap I.
View images
15/11/2010
12/ 20
5
Printing begins.
Current number of copies/
total number of copies
Monitor display returns to the print menu
shown in step 2 when printing is complete.
To cancel printing before all copies have been
printed, tap Cancel.
Printing
002/004
Cancel
C Paper Size
The camera supports the following paper sizes: Default (the default paper size for the printer
connected to the camera), 3.5 × 5 in., 5 × 7 in., 100 × 150 mm, 4 × 6 in., 8 × 10 in., Letter, A3, and
A4. Only sizes supported by the printer will be displayed. To specify paper size using printer settings,
choose Default in the Paper size option.
144
Basic Camera Setup
The Setup Menu
The setup menu contains the following options.
c
d
e
Welcome screen
Choose whether or not a welcome screen is displayed when camera is turned on.
Date
Set camera clock and choose home and destination time zones.
Monitor settings
Set the photo information displayed in playback mode, the image review settings,
and the monitor brightness.
f
Date imprint
Imprint shooting date and time on pictures.
Vibration reduction
g
h
u
i
k
Choose whether or not vibration reduction is enabled.
AF assist
Enable or disable AF-assist illuminator.
Digital zoom
Enable or disable digital zoom.
Sound settings
Adjust sound and volume when operating the camera.
Auto off
Set time before the monitor turns off for saving power.
l/m Format memory/Format card
Format internal memory or memory card.
n
H
V
Language
Choose the language used for camera monitor display.
TV settings
Adjust settings necessary for connection to television.
Charge by computer
Choose whether or not to charge the camera battery when connecting to a
computer via the USB cable.
d
Blink warning
Specify whether or not the camera detects human faces that have blinked with
shooting using face detection.
p
Reset all
Restore camera settings to default values.
Copy
h
r
Copy files between memory card and internal memory.
Firmware version
Display camera firmware version.
145
The Setup Menu
Operating the Setup Menu
1
2
3
Tap the bottom tab in shooting or
playback mode.
information.
T
W
36
Tap z.
The setup menu is displayed.
T
W
OFF
0.0
Tap the desired option.
Set up
Tap B or C to display previous or
subsequent page.
Welcome
Date
screen
Monitor
settings
Date imprint
AF assist
Tap J to return to the previous screen.
Vibration
reduction
When I is displayed in a screen, tap I to
apply the setting.
To exit the setup menu, tap J or press the
shutter-release button (when shooting).
146
The Setup Menu
c Welcome Screen
Choose whether or not a welcome screen is displayed when the camera is turned
on.
None (default setting)
The camera enters shooting or playback mode without displaying the welcome
screen.
COOLPIX
The camera displays a welcome screen and enters shooting or playback mode.
Select an image
Displays a picture selected for the
welcome screen. When the Select
Select image
image screen is displayed, select a
picture and tap I.
•
In the Select image screen, tap n to
switch to full-frame playback and tap
o to switch back to 9-thumbnail
display.
•
•
As the selected picture is stored in the
camera, it will be displayed when the camera is turned on even if the original
picture is deleted.
147
The Setup Menu
d Date
Set the camera clock.
Date
Set camera clock to current date and time.
Tap the items on the displayed
screen to select the display order of
the day, month and year, and set the
date and time.
Date
MDY
YMD
DMY
:
•
•
To select the item: tap the desired item.
To edit the highlighted item: tap A or
B.
01
01
2010 00 00
•
Time zone
Home time zone (w) can be specified and daylight saving time is enabled or
disabled from Time zone options. When Travel Destination (x) is selected, local
selected region are recorded with pictures. Useful when travelling.
Selecting Travel Destination Time Zone
1
Tap Time zone.
Date
:
15 11 2010 13 30
The time zone screen is displayed.
Date
Time zone
2
Tap x Travel destination.
Time zone
:
15 11 2010 15 30
The date and time displayed in the monitor
changes according to the region currently
selected.
London, Casablanca
Home time
zone
Travel
destination
148
|