DIGITAL CAMERA
User’s Manual
En
Basic Photography and Playback:
G
A
C
F
c
D
Taking Pictures of Smiling Faces
d
i
For Your Safety
To prevent damage to your Nikon product or injury to yourself or to others, read
the following safety precautions in their entirety before using this equipment.
Keep these safety instructions where all those who use the product will read them.
The consequences that could result from failure to observe the precautions listed
in this section are indicated by the following symbol:
This icon marks warnings, information that should be read before using this Nikon
product, to prevent possible injury.
WARNINGS
Turn off in the event of
malfunction
Do not use the camera or AC
adapter in the presence of
flammable gas
Should you notice smoke or an unusual
smell coming from the camera or AC
adapter, unplug the AC adapter and
remove the batteries immediately,
taking care to avoid burns. Continued
operation could result in injury. After
removing or disconnecting the power
source, take the equipment to a Nikon-
authorized service representative for
inspection.
Do not use electronic equipment in the
presence of flammable gas, as this
could result in explosion or fire.
Handle the camera strap with
care
Never place the strap around the neck
of an infant or child.
Keep out of reach of children
Particular care should be taken to
prevent infants from putting the
batteries or other small parts into their
mouths.
Do not disassemble
Touching the internal parts of the
camera or AC adapter could result in
injury. Repairs should be performed
only by qualified technicians. Should
the camera or AC adapter break open
as the result of a fall or other accident,
take the product to a Nikon-authorized
service representative for inspection,
after unplugging the product and/or
removing the batteries.
ii
For Your Safety
Observe caution when
handling batteries
Batteries may leak or explode if
improperly handled. Observe the
following precautions when handling
batteries for use in this product:
• Discontinue use immediately should
you notice any change in the
batteries, such as discoloration or
deformation.
•
If liquid from damaged batteries comes
in contact with clothing or skin, rinse
immediately with plenty of water.
• Before replacing the batteries, turn
the product off. If you are using an
AC adapter, be sure it is unplugged.
• Use only the batteries approved for
combine old and new batteries or
batteries of different makes or types.
• If Nikon rechargeable Ni-MH batteries
EN-MH2 (EN-MH2-B2 or EN-MH2-B4)
are purchased separately, charge and
use each of them as a set. Do not
combine batteries from different pairs.
• The EN-MH2 rechargeable batteries
are for use with Nikon digital cameras
only, and are compatible with
Observe the following
precautions when handling the
Battery Chargers (available
separately)
• Keep Dry. Failure to observe this
precaution could result in fire or
electric shock.
• Dust on or near the metal parts of the
plug should be removed with a dry
cloth. Continued use could result in
fire.
• Do not handle the power cable or go
near the battery charger during
lightning storms. Failure to observe
this precaution could result in
electric shock.
• Do not damage, modify, forcibly tug
or bend the power cable, place it
under heavy objects, or expose it to
heat or flame. Should the insulation
be damaged and the wires become
exposed, take it to a Nikon-
authorized service representative for
inspection. Failure to observe these
precautions could result in fire or
electric shock.
• Do not handle the plug or battery
charger with wet hands. Failure to
observe this precaution could result
in electric shock.
COOLPIX L24.
Do not use EN-MH2 rechargeable
batteries with incompatible devices.
•
Insert batteries in the correct orientation.
• Do not short or disassemble batteries
or attempt to remove or break
battery insulation or casing.
• Do not expose batteries to flame or
to excessive heat.
•
•
Do not immerse in or expose to water.
Do not transport or store with metal
objects such as necklaces or hairpins.
Batteries are prone to leakage when
fully discharged. To avoid damage to
the product, be sure to remove the
batteries when no charge remains.
•
iii
For Your Safety
•
Do not use with travel converters or
adapters designed to convert from one
voltage to another or with DC-to-AC
inverters. Failure to observe this
precaution could damage the product
or result in overheating or fire.
Do not operate the flash with
the flash window touching a
person or object
Failure to observe this precaution could
result in burns or fire.
Avoid contact with liquid
crystal
Use appropriate cables
When connecting cables to the input
and output jacks, use only the cables
provided or sold by Nikon for the
purpose, to maintain compliance with
product regulations.
Should the monitor break, care should
be taken to avoid injury caused by
broken glass and to prevent liquid
crystal from the monitor touching the
skin or entering the eyes or mouth.
Handle moving parts with care
Be careful that your fingers or other
objects are not pinched by the lens
cover or other moving parts.
Turn the power off when using
inside an airplane or the
hospital
Turn the power off while inside the
airplane during take off or landing.
Follow the instructions of the hospital
when using while in a hospital. The
electromagnetic waves given out by
this camera may disrupt the electronic
systems of the airplane or the
CD-ROMs
The CD-ROMs supplied with this device
should not be played back on audio CD
equipment. Playing CD-ROMs on an
audio CD player could cause hearing
loss or damage the equipment.
instruments of the hospital.
Observe caution when using
the flash
Using the flash close to your subject’s
eyes could cause temporary visual
impairment. Particular care should be
observed if photographing infants,
when the flash should be no less than 1
m (3 ft. 4 in.) from the subject.
iv
Notices
Notice for Customers in the U.S.A.
Federal Communications
Commission (FCC) Radio Frequency
Interference Statement
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced
radio/television technician for help.
CAUTIONS
Modifications
The FCC requires the user to be notified
that any changes or modifications
made to this device that are not
expressly approved by Nikon
Corporation may void the user’s
authority to operate the equipment.
Interface Cables
Use the interface cables sold or
provided by Nikon for your equipment.
Using other interface cables may
exceed the limits of Class B Part 15 of
the FCC rules.
Notice for customers in the State of
California
WARNING
Handling the cord on this product will
expose you to lead, a chemical known
to the State of California to cause birth
defects or other reproductive harm.
Wash hands after handling.
Nikon Inc.,
1300 Walt Whitman Road
Melville, New York 11747-3064
USA
Tel: 631-547-4200
v
Notices
Notice for customers in Canada
CAUTION
This Class B digital apparatus complies
with Canadian ICES-003.
ATTENTION
Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du
Canada.
Symbol for Separate Collection in
European Countries
This symbol indicates that this
product is to be collected
separately.
The following apply only to
users in European countries:
• This product is designated for
separate collection at an appropriate
collection point. Do not dispose of as
household waste.
• For more information, contact the
retailer or the local authorities in
charge of waste management.
This symbol on the battery
indicates that the battery is to
be collected separately.
The following apply only to
users in European countries:
• All batteries, whether marked with
this symbol or not, are designated for
separate collection at an appropriate
collection point. Do not dispose of as
household waste.
• For more information, contact the
retailer or the local authorities in
charge of waste management.
vi
Table of Contents
WARNINGS..................................................................................................................................................................ii
A (shooting mode) Button.............................................................................................................................8
c (playback) Button...........................................................................................................................................8
d Button .............................................................................................................................................................10
Help Displays..........................................................................................................................................................11
Attaching the Camera Strap.........................................................................................................................11
First Steps............................................................................................................................................. 12
Inserting the Batteries........................................................................................................................12
G Basic Photography and Playback: Easy Auto Mode ....................................................... 18
Step 1 Turn the Camera On and Select G (Easy Auto) Mode .............................................18
Indicators Displayed in G (Easy Auto) Mode....................................................................................19
Step 3 Focus and Shoot.....................................................................................................................22
Step 4 Viewing and Deleting Pictures..........................................................................................24
vii
Table of Contents
A Auto Mode..................................................................................................................................... 27
Exposure Compensation...................................................................................................................32
C Shooting Suited for the Scene................................................................................................ 33
F Taking Pictures of Smiling Faces (Smart Portrait Mode) .............................................. 44
Using Smart Portrait Mode...............................................................................................................44
c More on Playback....................................................................................................................... 46
Taking a Closer Look: Playback Zoom..........................................................................................48
Creating a Cropped Copy: Crop.................................................................................................................52
D Movies ............................................................................................................................................. 53
D Selecting Movie Options .........................................................................................................................54
Movie Playback.....................................................................................................................................55
viii
Table of Contents
Connecting to Televisions, Computers and Printers............................................................ 56
Connecting to a TV..............................................................................................................................56
Printing Multiple Pictures...............................................................................................................................65
d Shooting, Playback and Setup Menus ............................................................................. 70
Shooting Options: The Shooting Menu.......................................................................................70
A Image mode....................................................................................................................................................72
B White Balance................................................................................................................................................74
C Continuous ......................................................................................................................................................76
F Color Options .................................................................................................................................................77
Camera Settings that Cannot Be Set at the Same Time..............................................................78
b Slide Show........................................................................................................................................................81
c Delete...................................................................................................................................................................82
ix
Table of Contents
a Menus .................................................................................................................................................................85
c Welcome Screen...........................................................................................................................................86
d Date.......................................................................................................................................................................87
e Monitor Settings ..........................................................................................................................................90
f Date Imprint.....................................................................................................................................................92
w Electronic VR...................................................................................................................................................93
U Motion Detection.........................................................................................................................................94
h AF Assist............................................................................................................................................................95
i Sound Settings ..............................................................................................................................................96
k Auto Off..............................................................................................................................................................97
l Format Memory/m Format Card.......................................................................................................98
n Language...........................................................................................................................................................99
o Video Mode ................................................................................................................................................99
d Blink Warning...............................................................................................................................................100
p Reset All...........................................................................................................................................................101
s Battery Type..................................................................................................................................................103
d Protect ............................................................................................................................................................104
f Rotate Image................................................................................................................................................105
h Copy..................................................................................................................................................................106
r Firmware Version .....................................................................................................................................107
Approved Memory Cards............................................................................................................................109
Image File and Folder Names....................................................................................................... 110
Cleaning .................................................................................................................................................................113
Storage....................................................................................................................................................................114
Error Messages................................................................................................................................... 115
Supported Standards.....................................................................................................................................126
Index...................................................................................................................................................... 127
x
Introduction
About This Manual
Thank you for your purchase of a Nikon COOLPIX L24 digital camera. This manual
was written to help you enjoy taking pictures with your Nikon digital camera. Read
this manual thoroughly before use, and keep it where all those who use the
product will read it.
Symbols and Conventions
To make it easier to find the information you need, the following symbols and
conventions are used:
This icon marks cautions,
This icon marks tips, additional
information that should be read
information that may be helpful
B
C
D
before use, to prevent damage to
the camera.
when using the camera.
This icon indicates that more
information is available elsewhere
in this manual or in the Quick Start
Guide.
This icon marks notes, information
that should be read before using
the camera.
A
Notations
• Secure Digital (SD) memory card, SDHC memory card, and SDXC memory card
are referred to as “memory card.”
• The setting at the time of purchase is referred to as the “default setting.”
• The names of menu items displayed in the camera monitor, and the names of
buttons or messages displayed in the computer monitor appear in bold.
Screen Samples
In this manual, images are sometimes omitted from monitor display samples so
that monitor indicators can be more clearly shown.
Illustrations and Screen Display
Illustrations and text displays shown in this manual may differ from actual
appearance or display.
C Memory Cards
Pictures taken with this camera can be stored in the camera’s internal memory or on removable
memory cards. If a memory card is inserted, all new pictures will be stored on the memory card and
delete, playback and format operations will apply only to the pictures on the memory card. The
memory card must be removed before the internal memory can be formatted or used to store,
delete or view pictures.
1
Information and Precautions
Life-Long Learning
As part of Nikon’s “Life-Long Learning” commitment to ongoing product support and education,
continually updated information is available online at the following sites:
• For users in the U.S.A.: http://www.nikonusa.com/
• For users in Europe and Africa: http://www.europe-nikon.com/support/
• For users in Asia, Oceania, and the Middle East: http://www.nikon-asia.com/
Visit these sites to keep up-to-date with the latest product information, tips, answers to frequently
asked questions (FAQs), and general advice on digital imaging and photography. Additional
information may be available from the Nikon representative in your area. See the URL below for
contact information:
http://imaging.nikon.com/
Use Only Nikon Brand Electronic Accessories
Nikon COOLPIX cameras are designed to the highest standards and include complex electronic
circuitry. Only Nikon brand electronic accessories (including battery chargers, batteries and AC
adapters) certified by Nikon specifically for use with this Nikon digital camera are engineered and
proven to operate within the operational and safety requirements of this electronic circuitry.
THE USE OF NON-NIKON ELECTRONIC ACCESSORIES COULD DAMAGE THE CAMERA AND MAY
VOID YOUR NIKON WARRANTY.
For more information about Nikon brand accessories, contact a local authorized Nikon dealer.
Before Taking Important Pictures
Before taking pictures on important occasions (such as at weddings or before taking the camera on
a trip), take a test shot to ensure that the camera is functioning normally. Nikon will not be held liable
for damages or lost profits that may result from product malfunction.
About the Manuals
• No part of the manuals included with this product may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language in any form, by any means, without
Nikon’s prior written permission.
• Nikon reserves the right to change the specifications of the hardware and software described in
these manuals at any time and without prior notice.
• Nikon will not be held liable for any damages resulting from the use of this product.
• While every effort was made to ensure that the information in these manuals is accurate and
complete, we would appreciate it were you to bring any errors or omissions to the attention of the
Nikon representative in your area (address provided separately).
2
Information and Precautions
Notice Concerning Prohibition of Copying or Reproduction
Note that simply being in possession of material that was digitally copied or reproduced by means
of a scanner, digital camera or other device may be punishable by law.
• Items prohibited by law from being copied or reproduced
Do not copy or reproduce paper money, coins, securities, government bonds or local government
bonds, even if such copies or reproductions are stamped “Sample”. The copying or reproduction
of paper money, coins, or securities which are circulated in a foreign country is prohibited. Unless
the prior permission of the government was obtained, the copying or reproduction of unused
postage stamps or post cards issued by the government is prohibited. The copying or
reproduction of stamps issued by the government and of certified documents stipulated by law is
prohibited.
• Cautions on certain copies and reproductions
The government has issued cautions on copies or reproductions of securities issued by private
companies (shares, bills, checks, gift certificates, etc.), commuter passes or coupon tickets, except
when a minimum of necessary copies are to be provided for business use by a company. Also, do
not copy or reproduce passports issued by the government, licenses issued by public agencies
and private groups, ID cards and tickets, such as passes and meal coupons.
• Comply with copyright notices
The copying or reproduction of copyrighted creative works such as books, music, paintings,
woodcut prints, maps, drawings, movies and photographs is governed by national and
international copyright laws. Do not use this product for the purpose of making illegal copies or to
infringe copyright laws.
Disposing of Data Storage Devices
Please note that deleting images or formatting data storage devices such as memory cards or built-
in camera memory does not completely erase the original image data. Deleted files can sometimes
be recovered from discarded storage devices using commercially available software, potentially
resulting in the malicious use of personal image data. Ensuring the privacy of such data is the user’s
responsibility.
Before discarding a data storage device or transferring ownership to another person, erase all data
using commercial deletion software, or format the device and then completely refill it with images
containing no private information (for example, pictures of empty sky). Be sure to also replace any
property when physically destroying data storage devices.
3
Parts of the Camera
The Camera Body
2
1
3
4
Lens cover closed
5
6
10 11
9
8
7
1
2
5
6
7
Flash .....................................................................28
Speaker ..............................................................55
f
g
Power connector cover (for connecting
h
i
j
8
9
Eyelet for camera strap ............................11
3
4
4
Parts of the Camera
1
2 3 4
6 7 8 9
5
10
11 12
13 14
1
2
3
4
5
6
7
8
Monitor .................................................................6
Multi selector ....................................................9
Battery-chamber/
memory card slot cover ..................12, 16
9
10 Tripod socket
USB connector and audio/video
12
5
Parts of the Camera
The Monitor
The following indicators may appear in the monitor during shooting and playback
(actual display varies with current camera settings).
The indicators and photo info displayed during shooting and playback will turn off
Shooting
4
5
6
26
1
2 3
7
10
25
8
9
24
10 11
12
13
23
14
+1.0
22
21
999
1/125 F3.1
20
16
17
15
a
999
9999
b
1
1
m00
m00
s
s
18
19
*
1
2
3
4
5
6
7
8
9
AE/AF-L indicator ........................................ 43
Focus indicator ............................................. 22
Flash mode ..................................................... 28
Battery level indicator .............................. 18
Motion detection indicator ...........19, 94
Electronic VR .................................................. 93
a
Number of exposures remaining
(still pictures) ........................................... 18
15
*
* Differs according to the current shooting mode. Refer to the sections on each mode for details.
6
Parts of the Camera
Playback
1
2
3
4
15/05/2011 12:00
9999. JPG
14
13
11
12
10
5
6
999 999
7
a
9999 9999
9
8
999
999
b
1
1
m00s
m
s
00
1
2
3
4
5
6
Time of recording ....................................... 14
Battery level indicator .............................. 18
8
9
Internal memory indicator .................... 24
*
*
a
Current frame number/
total number of frames ..................... 24
7
* The displayed icons vary with the settings in shooting mode.
7
Basic Operations
A (shooting mode) Button
When A is pressed in playback mode, the camera
enters shooting mode.
When A is pressed in shooting mode, the
shooting-mode selection menu is displayed, which
allows you to change the shooting mode.
Shooting-mode Selection Menu
modes.
Easy auto mode
1
2
3
4
5
*
* The displayed icons vary depending on the last mode selected.
When A is pressed while the shooting-mode selection menu is displayed, the
camera returns to shooting mode without changing the current shooting mode.
c (playback) Button
During shooting mode, the camera enters the
playback mode when c is pressed.
If the camera is turned off, hold down c to turn the
camera on in playback mode.
8
Basic Operations
The Multi Selector
This section describes standard uses of the multi selector to select modes, select
menu options and to apply selection.
Operate the multi selector by pressing it up, down, left, right, and by pressing k.
For Shooting
Display o(exposure
compensation)
Display n
(self-timer) menu
Flash mode
Apply selection.
For Playback
15/05/2011 15:30
0004. JPG
Display the
previous picture.
Display the next
picture.
4
4
For the Menu Screen
Select the item
above.
Shooting menu
Image mode
White balance
Continuous
Apply selection (Go
to the next screen).
Select the item
to the left/return
to the previous
screen.
Select the item
below.
Color options
Select the item to
the right/go to the
next screen (apply
selection).
Exit
C Note on the Multi Selector
In this manual, H, I, J and K are used in some cases for indicating the up, down, left and right
operating parts of the multi selector.
9
Basic Operations
d Button
Press d to display the menu for the selected mode.
• Select a tab on the left side of the monitor to display the corresponding menu.
• To exit the menu display, press d again.
Upper tab: Menus available for
Shooting menu
the current mode are
Image mode
displayed.
White balance
Continuous
Lower tab: Display the setup
Color options
menu.
Exit
Displayed when the menu
contains two or more pages.
Set up
Motion detection
AF assist
Displayed when
there are more
previous menu
items.
Auto
Off
AF assist
Sound settings
Auto off
Format card
Language
Displayed when
there are one or
more menu items
to follow.
Exit
Exit
While an item is selected, press
k or the multi selector K to
display that item’s options.
Press k or the multi selector
K to apply selection.
Switching Between Tabs
Set up
Shooting menu
Shooting menu
Image mode
White balance
Continuous
Menus
Image mode
White balance
Continuous
Welcome screen
Date
Color options
Monitor settings
Date imprint
Electronic VR
Color options
Exit
Exit
Exit
Press the multi selector
J to highlight the tab.
Press the multi selector
HI to select a tab and
press k or K.
The selected menu will
be displayed.
When using the following modes, you can display the tabs by pressing the multi
selector J while the menu is displayed.
• Easy auto mode, scene mode, smart portrait mode and movie mode
10
Basic Operations
Help Displays
Rotate the zoom control to g (j) when M/j is displayed at the lower right of
the menu screen to view a description of the currently selected option.
To return to the original menu, rotate the zoom control to g (j) again.
Continuous
Choose single frame, continuous mode,
BSS (camera chooses sharpest shot in
series), or multi-shot 16.
Exit
Back
About the Shutter-release Button
The camera features a two-stage shutter-release button. To set focus and
exposure, press the shutter-release button halfway, stopping when you feel
resistance. Focus and exposure lock while the shutter-release button is held in this
position. To release the shutter and take a picture, press the shutter-release button
the rest of the way down. Do not use force when pressing the shutter-release
button, as this may result in camera shake and blurred pictures.
Press the shutter-
release button
halfway to set focus
and exposure.
Press the shutter-
release button the rest
of the way down to
take picture.
Attaching the Camera Strap
2
3
1
11
First Steps
Inserting the Batteries
1
Open the battery-chamber/memory card slot
cover.
3
Before opening the battery-chamber/memory card slot
cover, hold the camera upside down to prevent the
batteries from falling out.
1
2
2
Inserting the Batteries.
Confirm that the positive (+) and negative (–) terminals
are oriented correctly as described on the label at the
entrance of the battery chamber, and insert the batteries.
3
Close the battery-chamber/memory card slot
cover.
1
2
Applicable Batteries
• Two LR6/L40 (AA-size) alkaline batteries (batteries supplied)
• Two FR6/L91 (AA-size) lithium batteries
• Two EN-MH2 Ni-MH (nickel metal hydride) rechargeable batteries
Turning On and Off the Camera
Press the power switch to turn on the camera. After the
power-on lamp (green) lights for a moment, the
monitor turns on. When the camera turns off, both the
power-on lamp and monitor will turn off.
• If the camera is turned off, hold down c to turn the
12
Inserting the Batteries
B Removing the Batteries
Confirm the power-on lamp and the monitor are off and open the battery-chamber/ memory card
slot cover.
B Additional Precautions Regarding Batteries
• Be sure to read and follow the warnings for the battery on page iii and the section, “The Battery”
• Do not combine old and new batteries or batteries of different makes or types.
• Batteries with the following defects cannot be used:
Batteries with peeling
Batteries with insulation that
does not cover the area
Batteries with a flat
negative terminal
around the negative terminal.
B Notes for EN-MH1 Rechargeable Batteries, MH-70/71 Battery Charger
This camera can also use EN-MH1 Ni-MH rechargeable batteries.
Be sure to read and follow the warnings for the battery found in the section, “The Battery” (A 112),
before using the battery.
B Battery Type
in the camera, the batteries can perform more efficiently.
The default setting is the type of battery supplied with purchase. When any other type of battery is
C Alkaline Batteries
Performance of alkaline batteries may vary greatly depending on the manufacturer. Choose a
reliable brand.
C Alternative Power Sources
To power the camera continuously for extended periods, use an AC Adapter EH-65A (available
adapter. Failure to observe this precaution could result in overheating or in damage to the camera.
C Auto Power Off in Shooting Mode (Standby Mode)
If no operations are performed for about 30 seconds (default setting), the monitor will turn off
automatically and the camera will enter standby mode. After a further three minutes, the Auto off
function will turn the camera off automatically.
• While the monitor is off during standby mode (the power-on lamp flashes), it will turn on again
when the power switch, shutter-release button, A button, or c button is pressed.
• The time allowed to elapse before the camera enters standby mode can be changed from the
13
Setting Display Language, Date and Time
A language-selection dialog is displayed the first time the camera is turned on.
1
2
3
4
Press the power switch to turn on the camera.
The power-on lamp (green) will light for a moment and
the monitor will turn on.
Use the multi selector to choose
the desired language and press
k.
For information on using the multi selector,
Choose Yes and press k.
If No is selected, the date and time will not be set.
Date
Set time and date?
Yes
No
Cancel
Press J or K to select your home time zone
London
Casablanca
Back
D Daylight Saving Time
To use the camera in an area where daylight saving time is in effect,
press H on the home time zone in Step 4 to set the daylight saving
time to on.
London
Casablanca
When the daylight saving time setting is selected, the W mark
appears on the top of the monitor. To release the daylight saving
time setting, press I.
Back
14
Setting Display Language, Date and Time
5
6
7
8
Change the date and time.
Press H or I to edit the highlighted item.
Date
D
M
Y
Press K to move the cursor in the following order. D ->
M -> Y -> Hour -> Minute -> D M Y
01
01
2011
00
00
Press J to return to the previous item.
Edit
Choose the order in which the day, month
and year are displayed and press k or K.
The settings are applied.
Date
D
M
Y
15
05
2011
15
10
Edit
Press A to exit the screen.
The shooting-mode selection menu will be displayed.
Press this button
in shooting mode
for shooting-
mode selection
menu.
When Easy auto mode is displayed, press k.
The camera enters the shooting mode and you can take
Easy auto mode
Press the multi selector H or I before k, to switch to
another shooting mode. See “Shooting in the Auto
D Changing the Date and Time, Date Imprint
follow the instructions starting from the above step 5.
• To change the time zone and the daylight saving settings, select Time zone from Date in the
• To imprint the shooting date into images when taking pictures, make sure the date and time are
15
Inserting Memory Cards
Images are saved in the camera’s internal memory (approximately 17 MB) or on
If a memory card is inserted in the camera, pictures are automatically stored on the
memory card and pictures recorded to the memory card can be played back,
deleted or transferred. Remove the memory card to store pictures in the internal
memory, or play back, delete or transfer pictures from the internal memory.
1
Confirm the power-on lamp and the monitor
are off and open the battery-chamber/
memory card slot cover.
3
Be sure to turn off the camera before opening the
battery-chamber/memory card slot cover.
1
2
Before opening the battery-chamber/memory card slot
cover, hold the camera upside down to prevent the
batteries from falling out.
2
Insert the memory card.
Slide the memory card in correctly until it clicks into
place.
Close the battery-chamber/memory card slot cover.
B Inserting Memory Cards
Inserting the memory card upside down or backwards could
damage the camera or the memory card. Make sure that the
memory card is correctly oriented.
16
Inserting Memory Cards
Removing Memory Cards
Before removing memory cards, turn the camera off
and confirm that the power-on lamp and the monitor
are off. Open the battery-chamber/memory card slot
cover and press the card in (1) to partially eject the
card. Remove the card (2), being careful not to bend
it.
1
2
B Formatting Memory Cards
Card is not formatted.
Format card?
If the message shown on the right is displayed, the memory card
must be formatted before use. Note that formatting permanently
deletes all pictures and other data on the memory card. Be sure
to make copies of any pictures you wish to keep before formatting
the memory card.
Yes
No
To format, use the multi selector to select Yes and press k. The
confirmation dialog will be displayed. To start formatting, choose Format and press k.
•
•
Do not turn the camera off or open the battery-chamber/memory card slot cover until formatting is complete.
The first time you insert the memory cards used in other devices into the camera, be sure to
B The Write Protect Switch
SD memory cards are equipped with a write protect switch.
Pictures cannot be recorded or deleted and the memory card
cannot be formatted when this switch is in the “lock” position.
Unlock by sliding the switch to the “write” position.
Write protect switch
B Memory Cards
• Use only Secure Digital memory cards.
• Do not perform the following during formatting, while data
is being written to or deleted from the memory card, or during data transfer to a computer. Failure
to observe this precaution could result in the loss of data or in damage to the camera or memory
card:
- Insert or remove the card
- Remove the batteries
- Turn off the camera
- Disconnect the AC adapter
• Do not format the memory card using a computer.
• Do not disassemble or modify.
• Do not drop, bend, or expose to water or strong physical shocks.
• Do not touch the metal terminals with your fingers or metal objects.
• Do not affix labels or stickers to the memory card.
• Do not leave in direct sunlight, closed vehicles or areas exposed to high temperatures.
• Do not expose to humidity, dust, or to corrosive gases.
17
Basic Photography and Playback: Easy Auto Mode
Step 1 Turn the Camera On and Select
G
(Easy Auto) Mode
In G (easy auto) mode, the camera automatically determines an appropriate
shooting mode when you frame a picture, allowing you to easily take pictures
1
Press the power switch to turn on the camera.
The power-on lamp (green) will light for a moment and
the monitor will turn on. The lens will extend at this time.
Easy auto mode is set at the time of purchase. Proceed to
step 4.
2
3
Press A to display the shooting-mode
selection menu.
Press the multi selector HI to choose G
and press k.
Easy auto mode
The camera enters G (easy auto) mode.
4
Check the battery level and number of
exposures remaining.
Battery level indicator
Battery level indicator
Monitor
Description
NO INDICATOR
The battery level is high.
Batteries low.
Prepare to replace batteries.
B
4
N
Cannot take pictures. Replace
with new batteries.
Number of exposures
remaining
Battery
exhausted.
Number of Exposures Remaining
The number of pictures that can be stored depends on the capacity of the internal
18
Step 1 Turn the Camera On and Select G (Easy Auto) Mode
Indicators Displayed in G (Easy Auto) Mode
Shooting mode
When using easy auto mode, U, e, f,
g, h, i, or j is displayed to
indicate the shooting mode selected by the
camera for the current subject and framing.
Motion detection indicator
Reduce the blurring caused by
subject or camera shake.
4
Internal memory indicator
Pictures will be recorded to internal memory
(approximately 17 MB).
Image mode
Display image size and quality set in
the image mode menu.
When memory card is inserted, C is not
displayed and pictures will be recorded to
memory card.
The default setting is k 4320 × 3240.
The indicators and photo info displayed during shooting and playback will turn off
When the monitor has turned off in standby mode to save power, press the power
C Available Functions in Easy Auto Mode
• When the camera is pointed at a person’s face, the camera automatically detects the face and
when the camera selects close-up scene mode.
D Motion Detection
D Electronic Vibration Reduction
setup menu is set to Auto, the R icon may be displayed in the monitor. R indicates shooting
conditions in which the effects of camera shake can be pronounced. In these situations, the camera
reduces the effects of camera shake in pictures before saving them.
19
Step 2 Frame a Picture
1
Ready the camera.
Hold the camera steadily in both hands, keeping your
fingers and other objects away from the lens, flash, self-
timer lamp and microphone.
When taking pictures in “tall” orientation, turn the camera
so that the flash is above the lens.
2
Frame the picture.
When the camera determines the scene mode, the
Shooting mode icon
When the camera detects a human face, that face will be
framed by a yellow double border.
Up to 12 faces can be recognized. If more than one face is
recognized, the face closest to the camera will be framed
in the focus area by a double border, and the other faces
will be framed by a single border.
4
When shooting non-human subjects or when no faces are detected, focus will be in the
center of the monitor. Position the main subject near the center of the monitor.
B Easy Auto Mode
• The desired scene mode may not be selected in certain conditions. In this case, select another
shooting mode.
• When digital zoom is in effect, the shooting mode is U.
20
Step 2 Frame a Picture
Using the Zoom
Use the zoom control to activate optical zoom.
f Zoom out g Zoom in
Rotate the zoom control to g to zoom in on the
subject.
Rotate the zoom control to f to zoom out.
The zoom indicator is displayed at the top of the
monitor when the zoom control is rotated.
Optical zoom Digital zoom
Digital Zoom
When the camera is zoomed in to the maximum optical zoom position, rotating
and holding the zoom control at g triggers digital zoom. Digital zoom can
magnify the subject up to about 4× beyond the magnification of the optical
zoom.
The focus area is not displayed when digital zoom is in effect, and focus will be in
the center of the screen.
Maximum magnification
of optical zoom.
Digital zoom is in effect.
C Digital Zoom and Interpolation
Unlike optical zoom, digital zoom uses a digital imaging process known as interpolation to magnify
images, resulting in slight deterioration of picture quality.
Interpolation is applied at zoom positions beyond V.
When zoom is increased beyond the V position, interpolation is initiated and the zoom indicator
turns yellow to indicate that interpolation is being applied.
The position of V moves to the right as image size decreases, allowing for confirmation of the
zoom positions at which shooting without interpolation is possible at the current image mode
setting.
When the image size is small.
21
Step 3 Focus and Shoot
1
Press the shutter-release button halfway.
focus, the focus area will glow green.
When a face is detected:
When no faces are detected:
1/125 F3. 1
1/125 F3.1
Shutter Aperture
Speed
Focus indicator
When using the digital zoom, the camera
focuses on the center of the frame, but
the focus area is not displayed. When the
subject is in focus, the focus indicator
1/125 F6.7
The shutter speed and aperture are displayed when the shutter-release button is
pressed halfway.
Focus and exposure remain locked while the shutter release button is pressed halfway.
When the camera is unable to focus, the focus area, or focus indicator, blinks red.
Change the composition and try pressing the shutter-release button halfway again.
2
Press the shutter-release button the rest of
the way down.
The picture will be recorded to the memory card or
internal memory.
22
Step 3 Focus and Shoot
B During Recording
While pictures are being recorded, the number of exposures remaining display will blink. Do not
open the battery-chamber/memory card slot cover.
Removing the battery or the memory card while data is being saved may result in loss of data or in
damage to the saved data, camera or card.
B Autofocus Performance
Autofocus may not perform as expected in the following situations. In some rare cases, the subject
may not be in focus despite the fact that the focus area or the focus indicator glows green:
• Subject is very dark
• Objects of sharply differing brightness are included in the scene (e.g. the sun is behind the subject
and the subject is in deep shadow)
• No contrast between the subject and surroundings (e.g. when the subject is standing in front of a
white wall, wearing a white shirt)
• Several objects are at different distances from the camera (e.g. the subject is inside a cage)
• Subject is moving rapidly
In these situations, try pressing the shutter-release button halfway again to refocus, several times if
necessary. If the subject is still not in focus, select auto mode and use focus lock (A 27) to take the
picture by first focusing on an object that is the same distance from the camera as the desired
subject.
C Notes about Face Detection
C The Did someone blink? Screen
taking a picture if the camera detects a face with closed eyes.
D AF-assist Illuminator and Flash
If the subject is poorly lit, the AF-assist illuminator (A 95) may light when the shutter-release button
is pressed halfway, and the flash (A 28) may fire when the shutter-release button is pressed all the
way down.
23
Step 4 Viewing and Deleting Pictures
Viewing Pictures (Playback Mode)
Press c (playback).
A (shooting mode) button
The last picture taken will be displayed in full-frame
playback mode.
c (playback)
Use the multi selector H, I, J or K to view
additional pictures. Hold down the multi selector H,
I, J, or K to scan quickly through pictures.
Pictures may be displayed briefly at low resolution
while being read from the memory card or internal
memory.
Multi selector
Press A to switch to shooting mode.
When C is displayed, pictures stored in the internal memory
will be displayed. When memory card is inserted, C is not
displayed and pictures stored on the memory card will be
displayed.
15/05/2011 15:30
0004.JPG
4
4
Internal memory
indicator
Deleting Pictures
1
Press l to delete the picture currently
displayed in the monitor.
2
Use the multi selector to select Yes and press
k.
Erase 1 image?
Deleted pictures cannot be recovered.
To exit without deleting the picture, choose No and press
k.
Yes
No
24
Step 4 Viewing and Deleting Pictures
C Playback Mode
The following options are available in full-frame playback mode.
Option
Use
Description
A
The picture can be enlarged up to about
10×. Press k to return to full-frame
playback.
Playback zoom
g (i)
Rotate the zoom control to f to display
4, 9 or 16 picture thumbnails.
View thumbnails
f (h)
While viewing 16 picture thumbnails,
rotate the zoom control to f (h) to
switch to calendar display.
8
Switch to shooting
mode
A
Press A.
C Power ON by Pressing c
When the camera is off, hold down c to turn on the camera in playback mode. The lens will not
extend.
C Viewing Pictures
• Pictures stored in the internal memory can only be viewed if no memory card is inserted.
frame.
• When the monitor has turned off in standby mode to save power, press the power switch, the
C Deleting the Last Picture Taken While in Shooting Mode
In shooting mode, press l to delete the last picture taken.
Erase 1 image?
Yes
No
D Selecting Multiple Pictures for Deletion
deleted.
25
Easy auto mode
Automatic Scene Selection
The camera automatically selects one of the following scenes when you point the
camera at a subject.
• U Auto mode (general use)
Notes about Face Detection
• Depending on shooting conditions, such as whether or not the subject is facing
the camera, faces may not be detected.
The camera may be unable to detect faces in the following situations:
-
-
When faces are partially hidden by sunglasses or other obstructions
When faces take up too much or too little of the frame
• When there are multiple people in the frame, the face on which the camera
focuses depends on a variety of shooting conditions, such as whether or not the
subject is facing the camera.
autofocus may not perform as expected, and the subject may not be in focus
despite the fact that the double border glows green. When the camera is
unable to focus, use another mode, such as A (auto) mode, focus on another
subject positioned at the same distance from the camera as the actual portrait
26
Auto Mode
Shooting in the Auto Mode
1
Press A to display the shooting-mode
selection menu.
The shooting-mode selection menu will be displayed.
2
Press the multi selector H or I to choose A
and press k.
The camera enters A (auto) mode.
to shooting conditions.
Auto mode
By pressing d, you can also set the items in the
3
Frame the subject and shoot.
Camera focuses on subject in center of
frame.
4
D Focus Lock
When the camera focuses on an object in the center of the frame, you can use focus lock to focus on
an off-center subject.
•
Be sure that the distance between the camera and the subject does not change while focus is locked.
• When the shutter-release button is pressed halfway, exposure is locked.
4
1/125 F3.1
1/125 F3.1
Position the subject Press the Confirm that the Continue holding
in the center of the shutter focus area is down the shutter-
Press the
shutter-
frame.
release
button
halfway.
green.
release button halfway release button
and recompose the
picture.
the rest of the
way down.
27
Using the Flash
The flash mode allows you to specify the settings according to shooting conditions.
• The flash has a range of approx. 0.5-7.0 m (1 ft. 8 in.-22 ft.) at the maximum wide-
angle zoom position and a range of approx. 0.5-3.0 m (1 ft. 8 in.-9 ft. 10 in.) at the
maximum telephoto zoom position.
and W Off are available. When U Auto is applied, the camera automatically
selects the optimum flash mode setting for the scene mode it has selected.
Auto
U
V
W
Flash fires automatically when lighting is poor.
Auto with red-eye reduction
Off
Flash will not fire even when lighting is poor.
Fill flash
X
Flash fires when a picture is taken. Use to “fill-in” (illuminate) shadows and back-lit subjects.
Slow sync
Y
Auto flash mode is combined with slow shutter speed.
Suitable for taking portraits with the night landscape as the background. Flash
illuminates main subject; slow shutter speeds are used to capture background at
night or under dim light.
Setting the Flash Mode
1
Press m (flash mode) on the multi selector.
The flash menu is displayed.
2
Press the multi selector H or I to select a
mode and press k.
The icon for the selected flash mode is displayed at the
top of the monitor.
D will disappear after a few seconds regardless of the
Flash mode
If a setting is not applied by pressing k within a few
seconds, the selection will be cancelled.
28
Using the Flash
B Shooting When Lighting Is Poor and the Flash Is Disabled (W)
• Use of a tripod is recommended to stabilize the camera during shooting and avoid the effects of
camera shake.
• The E is displayed when the camera automatically increases sensitivity to minimize blur caused
by slow shutter speed. Pictures taken when E is displayed may be slightly mottled.
B Note on Using the Flash
When using the flash, reflections from dust particles in the air may appear as bright spots in pictures.
To reduce these reflections, set the flash to W (Off).
C The Flash Lamp
The flash lamp indicates flash status when the shutter-
release button is pressed halfway.
• On:
Flash will fire when picture is taken.
• Blinks: Flash charging. Wait a few seconds and try
again.
• Off:
Flash will not fire when picture is taken.
If the remaining battery level is low, the monitor will turn off until the flash has finished charging.
C The Flash Mode Setting
The default setting of the flash mode depends on the shooting mode.
• G (easy auto): U Auto
• F (smart portrait): U Auto
• A (auto): U Auto
When the shooting mode is A (auto) mode, the changed flash setting will be stored even if the
camera is turned off.
C Red-eye Reduction
This camera uses advanced red-eye reduction (“In-Camera Red-Eye Fix”).
If the camera detects “red-eye” when a picture is taken, Nikon’s own In-Camera Red-Eye Fix
processes the image before it is saved.
Note the following when taking pictures:
• The time required to save images increases slightly.
• Red-eye reduction may not always produce the desired results.
• In some rare cases, other portions of pictures may be affected. Use flash modes other than auto
with red-eye reduction in above cases.
29
Taking Pictures with the Self-timer
When using the self-timer, pictures are taken 10 seconds after the shutter-release
button is pressed. When using the self-timer, use of a tripod is recommended.
1
Press n (self-timer) on the multi selector.
The self-timer menu is displayed.
2
Press the multi selector H or I to select ON
and press k.
The self-timer icon (n 10) is displayed.
If a setting is not applied by pressing k within a few
seconds, the selection will be cancelled.
Self-timer
1/125 F3.1
1/125 F3.1
3
4
Frame the picture and press the
shutter-release button halfway.
Focus and exposure will be set.
10
Press the shutter-release button the
rest of the way down.
9
The self-timer starts and the number of seconds
remaining until the shutter is released is
displayed in the monitor. The self-timer lamp
will blink. The lamp stops blinking one second
before the picture is taken and remains lit until
the shutter is released.
When the shutter is released, the self-timer will be set to OFF.
To stop the timer before a picture is taken, press the
shutter-release button again.
30
Macro Mode
Macro mode is used for taking pictures of objects as close as 5 cm (2 in.). Note that
the flash may be unable to light entire subject at distances of less than 50 cm (1 ft.
8 in.).
used to activate macro mode.
1
2
Press p (macro mode) on the multi selector.
The macro menu is displayed.
Press the multi selector H or I to select ON
and press k.
The macro mode icon (F) is displayed.
If a setting is not applied by pressing k within a few
seconds, the selection will be cancelled.
Macro mode
3
Rotate the zoom control to move to the wide
zoom position.
Macro mode can be used to take a picture at the current
zoom position when F or the zoom indicator glows
green.
The camera can focus on objects as close as about 5 cm (2 in.) at the widest zoom
position, and as close as about 7 cm (2.8 in.) at the position where G is displayed.
C Autofocus
When using macro mode, the camera focuses continuously until the shutter-release button is
pressed halfway to lock the focus. A sound will be heard while the camera focuses.
C The Macro Mode Setting
When the shooting mode is A (auto) mode, the macro mode setting will be stored even if the
camera is turned off.
31
Exposure Compensation
Exposure compensation is used to alter exposure from the value suggested by the
camera to make pictures brighter or darker.
1
Press o (exposure compensation) on the
multi selector.
The exposure compensation guide is displayed.
2
Press the multi selector H or I to select the
desired setting and press k.
To make the subject brighter, adjust the exposure
compensation to the “+” side.
To make the subject darker, adjust the exposure
compensation to the “-” side.
Exposure compensation
Exposure compensation can be set to values between
-2.0 and +2.0 EV.
If a setting is not applied by pressing k within a few seconds, the selection will be
cancelled.
When set to any value other than 0.0, H and the value are displayed.
3
Press the shutter-release button to shoot.
To turn off exposure compensation, repeat from step 1
and set the value to 0.0, then press k.
4
C Exposure Compensation Value
stored even if the camera is turned off.
32
Shooting Suited for the Scene
Using the Scene Mode
Camera settings are automatically optimized for the selected subject type. The
following scene modes are available.
b Portrait
f Party/indoor
g Beach/snow
h Sunset
j Night landscape m Fireworks show
c Landscape
d Sports
k Close-up
u Food
n Copy
o Backlight
p Panorama assist
e Night portrait
i Dusk/dawn
l Museum
Setting the Scene Mode
1
Press A in shooting mode to
display the shooting-mode
selection menu and use the multi
selector H and I to select scene
mode.
Portrait
The icon of the last scene mode used is
displayed. b (Portrait) is the default setting.
2
3
Press K, press H, I, J, or K to select a scene
mode, then press k.
The shooting mode screen for the selected scene is
displayed.
Beach/snow
Frame the subject and shoot.
4
D Image Mode
image mode setting is changed, the new image mode setting is also applied to other shooting
modes (except movie mode).
33
Using the Scene Mode
Features
The following icons are used for descriptions in this section: X = flash mode
b Portrait
Use this mode for taking portraits in which the main subject
stands out clearly.
•
If the camera detects a face, it focuses on the face. See “Face
•
If more than one face is recognized, the camera focuses on
the face closest to the camera.
•
•
If no faces are detected, focus will be on the center of the frame.
Digital zoom is not available.
m
V*
n
Off*
p
Off
o
0.0*
* Other settings can be selected.
c Landscape
Use this mode for vivid landscapes and cityscapes.
•
Camera focuses at infinity. The focus area or focus indicator
is pressed halfway. Note, however, that objects in the
foreground may not always be in focus.
•
m
W
n
Off*
p
Off
o
0.0*
* Other settings can be selected.
34
Using the Scene Mode
d Sports
Use this mode for dynamic action shots that freeze the action
in a single shot and record motion in a series of pictures.
•
The camera focuses on the subject in the center of the
frame. The camera focuses continuously until the shutter-
release button is pressed halfway to lock the focus.
While the shutter-release button is held down all the way,
•
the camera shoots up to three images at a rate of about 0.7 frames per second (fps)
(when image mode is set to R 4320 × 3240).
The maximum frame rate with continuous shooting may vary depending upon the
current image mode setting and the memory card used.
Focus, exposure compensation, and white balance are fixed at the values determined
with the first shot in each series.
•
•
•
m
W
n
Off
p
Off
o
0.0*
* Other settings can be selected.
e Night portrait
O
Use this mode to achieve a natural balance between the main
subject and background lighting in portraits taken at night.
Flash is used to illuminate the subject while maintaining the
mood of the background.
•
If the camera detects a person’s face, the camera will focus
•
If more than one face is recognized, the camera focuses on the face closest to the
camera.
•
•
If no faces are recognized, focus will be on the center of the screen.
Digital zoom is not available.
*1
*2
*2
m
V
n
Off
p
Off
o
0.0
*1
Flash mode is set to fill flash with slow sync and red-eye reduction, and cannot be changed.
Other settings can be selected.
*2
O: For those scene modes with O, use of a tripod is recommended.
35
Using the Scene Mode
f Party/indoor
Captures the effects of candlelight and other indoor
background lighting.
•
•
Camera focuses on subject in center of frame.
As pictures are easily affected by camera shake, hold the
camera steadily. In a dark place, the use of a tripod is
recommended.
1
2
2
m
V*
n
Off*
p
Off
o
0.0*
*1
The flash may change to slow sync with red-eye reduction. Other settings can be selected.
Other settings can be selected.
*2
g Beach/snow
Captures the brightness of such subjects as snowfields,
beaches, or sunlit expanses of water.
•
Camera focuses on subject in center of frame.
m
U*
n
Off*
p
Off*
o
0.0*
* Other settings can be selected.
h Sunset
O
Preserves the deep hues seen in sunsets and sunrises.
Camera focuses on subject in center of frame.
•
m
W*
n
Off*
p
Off
o
0.0*
* Other settings can be selected.
O: For those scene modes with O, use of a tripod is recommended.
36
Using the Scene Mode
i Dusk/dawn
O
Preserves the colors seen in the weak natural light before
sunrise or after sunset.
•
Camera focuses at infinity. The focus area or focus indicator
is pressed halfway. Note, however, that objects in the
foreground may not always be in focus.
•
m
W
n
Off*
p
Off
o
0.0*
* Other settings can be selected.
j Night landscape
O
Slow shutter speeds are used to produce stunning night
landscapes.
•
Camera focuses at infinity. The focus area or focus indicator
is pressed halfway. Note, however, that objects in the
foreground may not always be in focus.
•
m
W
n
Off*
p
Off
o
0.0*
* Other settings can be selected.
O: For those scene modes with O, use of a tripod is recommended.
37
Using the Scene Mode
k Close-up
Photograph flowers, insects and other small objects at close
range.
•
to a position that allows macro shooting.
•
The camera can focus on objects as close as about 5 cm
(2 in.) at the widest zoom position, and as close as about
7 cm (2.8 in.) at the position where G is displayed.
Camera focuses on subject in center of frame. Use focus lock to frame the picture on an
The camera focuses continuously until focus is locked by pressing the shutter-release
button halfway.
•
•
m
W*
n
Off*
p
On
o
0.0*
* Other settings can be selected. Note that the flash may be unable to light entire subject at
distances of less than 50 cm (1 ft. 8 in.).
u Food
Use this mode when taking pictures of food. See “Taking
•
Camera focuses on subject in center of frame.
m
W
n
Off*
p
On
o
0.0*
* Other settings can be selected.
l Museum
Use indoors where flash photography is prohibited (for
example, in museums and art galleries) or in other settings in
which you do not want to use the flash.
•
•
•
Camera focuses on subject in center of frame.
As pictures are easily affected by camera shake, hold the
camera steadily.
•
m
W
n
Off*
p
Off*
o
0.0*
* Other settings can be selected.
38
Using the Scene Mode
m Fireworks show
O
Slow shutter speeds are used to capture the expanding burst
of light from fireworks.
•
Camera focuses at infinity. When the shutter-release button
green. Note, however, that objects in the foreground may
not always be in focus.
•
m
W
n
Off
p
Off
o
0.0
n Copy
Provides clear pictures of text or drawings on a white board or
in print.
•
•
•
Camera focuses on subject in center of frame.
Colored text and drawings may not show up well.
m
W*
n
Off*
p
Off*
o
0.0*
* Other settings can be selected.
o Backlight
Use when light is coming from behind your subject, throwing
features or details into shadow. The flash fires automatically to
“fill in” (illuminate) shadows.
•
Camera focuses on subject in center of frame.
m
m
n
Off*
p
Off
o
0.0*
* Other settings can be selected.
O: For those scene modes with O, use of a tripod is recommended.
39
Using the Scene Mode
Taking Pictures for Food Mode
Use this mode when taking pictures of food.
1
2
3
Press A in shooting mode to display the
shooting-mode selection menu and use the
automatically move to the closest possible shooting
position.
Food
Press the multi selector H or I to adjust the
color if necessary.
You can adjust the hues to compensate for changes in
the subject’s color caused by the surrounding lighting.
Press H to increase the amount of red, or I to increase
the amount of blue.
4
Frame the picture.
The camera can focus on objects as close as about 5 cm (2
in.) at the widest zoom position, and as close as about 7
cm (2.8 in.) at the position where G is displayed.
The camera focuses on the subject in the center of the
frame. Use focus lock to frame the picture on an object
4
4
Press the shutter-release button to
shoot.
Pressing the shutter-release button halfway
locks the focus, and pressing the shutter-
release button the rest of the way down takes
the picture.
1/125 F3.1
When the camera is unable to focus, the focus
area will blink. Change the composition and try pressing the shutter-release button
halfway again.
B Notes when Using the Food Mode
C Adjusting Hues When Using Food Mode
Hue settings that are adjusted in food mode are saved in the camera’s memory even after the
camera is turned off, and are used the next time food mode is selected.
41
Using the Scene Mode
Taking Pictures for a Panorama
The camera focuses on the subject in the center of the frame. Use a tripod for best
results.
1
Press A in shooting mode to display the
shooting-mode selection menu and use the
multi selector to select p Panorama assist
The panorama direction icon (I) is displayed to show the
Panorama assist
direction in which pictures will be joined.
2
Use the multi selector to choose the direction
and press k.
Select how pictures will be joined together in the
completed panorama; right (I), left (J), up (K) or down
(L).
4
The yellow panorama direction icon (II) is displayed to
the direction pressed and the direction is fixed when k
is pressed. The white fixed direction I is displayed.
direction.
3
4
Shoot the first picture.
The first picture is superimposed in the first
third of the monitor.
4
Shoot the second picture.
Frame the next picture so that one third of the
frame overlaps the first picture, and press the
shutter-release button.
Repeat until you have taken the necessary
number of pictures to complete the scene.
End
3
42
Using the Scene Mode
5
Press k when shooting is completed.
The camera returns to step 2.
End
1
B Panorama Assist
Set flash mode, self-timer, macro mode and exposure compensation before taking the first picture.
They cannot be changed after the first picture is taken. Pictures cannot be deleted, nor can zoom or
The panorama series is terminated if the camera enters standby mode with the auto off function
to a longer setting is recommended.
D Note on R
When using panorama assist mode, all pictures taken in a
panorama series have the same white balance, exposure, and focus
settings as the first picture taken.
When the first picture is shot, R is displayed to indicate that
exposure, white balance, and focus are locked.
Ennd
3
D Panorama Maker 5
Install Panorama Maker 5 from the supplied ViewNX 2 CD.
panorama.
D More Information
43
Taking Pictures of Smiling Faces (Smart Portrait Mode)
Using Smart Portrait Mode
The camera detects a smiling face to shoot the face automatically.
1
Press A in shooting mode to
display the shooting-mode
selection menu and use the multi
selector H and I to select F,
then press k.
Smart portrait
2
Frame the picture.
Point the camera at the subject.
If the camera detects a person’s face, the face will be
framed by a double yellow border in the focus area, and
when the face comes into focus, the double border will
instantly turn green and the focus will be locked.
1/125 F3.1
Up to three faces will be recognized. When the faces of
multiple people are detected, the face nearest the center of the frame will be framed by
a double border in the focus area and the other faces will be framed by a single border.
3
4
The shutter is automatically released.
If the camera detects the smiling face of the person framed by a double border, the
shutter is automatically released.
shutter is released, the self-timer lamp blinks rapidly.
Each time the shutter is released, the camera again begins face detection and smile
detection operations for continuous automatic shooting.
Pictures can also be taken by pressing the shutter-release button. If the camera does not
detect any faces, the camera focuses on the subject in the center of the frame.
Press A to exit smart portrait mode.
Change to another shooting mode.
44
Using Smart Portrait Mode
B Face Detection and Smiling Face Detection Features
If the camera is pointed at a person’s face while the camera is in smart portrait mode, the face is
automatically detected, and the smile of the detected face can also be detected.
• In some shooting conditions, face recognition does not work and faces cannot be detected.
C Auto Off (Standby Mode) When Using Smart Portrait Mode
performed in the following situations:
• The camera does not recognize any faces.
• The camera detected a face but cannot detect a smiling face.
C Functions Available in Smart Portrait Mode
adjusted. If the image mode setting is changed, the new image mode setting is also applied to
other shooting modes (except movie mode).
• Digital zoom is not available.
D More Information
45
More on Playback
Viewing Multiple Pictures: Thumbnail Playback
Rotate the zoom control to f (h) in full-frame
1
9
sheets” of thumbnail images. The following operations
can be performed while thumbnails are displayed.
To
Use
Description
A
Choose pictures
Press the multi selector H, I, J or K.
9
Rotate the zoom control to f (h) to
change the number of frames
displayed from 4 ➝ 9 ➝ 16, or to
display the calendar. When the
calendar is displayed, you can select
images to view based on the day they
Display the calendar/
Change the number of
frames displayed
f (h)
g (i)
Rotate the zoom control to g (i) to
return to thumbnail display mode.
–
Rotate the zoom control to g (i) to
change the number of frames
displayed from 16 ➝ 9 ➝ 4. While 4
frames are displayed, rotate the zoom
control to g (i) again to return to full-
frame display mode.
Reduce the number of
frames displayed
g (i)
Switch to full-frame
playback
k
Press k.
24
8
Switch to shooting
mode
A
Press A.
C Thumbnail Playback Mode Display
Protect icon
Print-order icon
right are displayed with them. Movies are displayed
as film frames.
1
9
Film frames
46
Viewing Multiple Pictures: Thumbnail Playback
Calendar Display
Rotate the zoom control to f (h) when the pictures
mode to switch to calendar display.
You can select images to view based on the day they
were taken. Days containing pictures have a yellow line
under them.
6
The following operations are available in calendar display.
To
Use
Description
A
Choose date
Press the multi selector H, I, J or K.
9
Switch to full-frame
playback
The first picture for that date will be
displayed full-frame.
k
–
Switch to thumbnail
display
g (i)
Rotate the zoom control to g (i).
B Calendar Display
• Pictures taken when the camera’s date is not set are treated as pictures taken on January 1, 2011.
• The l and d buttons are not available during calendar display.
47
Taking a Closer Look: Playback Zoom
Rotating the zoom control to g (i) during full-frame
the center of the picture displayed in the monitor.
• The guide displayed in the right bottom in the
monitor will show which part of the image is
currently displayed.
×
3.0
The following operations can be performed while pictures are zoomed in.
To
Use
Description
A
Rotate the zoom control to g (i).
Images can be magnified by up to 10×.
Zoom in
g (i)
–
Rotate the zoom control to f (h).
When the magnification ratio reaches
1×, the display returns to full-frame
playback mode.
Zoom out
f (h)
–
Press the multi selector H, I, J or K
to scroll to areas of the picture not
visible in the monitor.
View other areas of
picture
Switch to full-frame
playback
k
d
A
Press k.
24
Press d to crop current picture to
monitor.
Crop picture
Switch to shooting
mode
Press A.
8
Pictures Taken Using Face Detection
When the zoom control is rotated to g (i) during full-
frame playback mode, pictures taken using face
was focused on at the time of shooting as the
centralized point.
×
2.0
• If several faces are recognized, the picture will be
enlarged using the face which was focused on
during shooting time as the centralized point, and pressing the multi selector
H, I, J or K will enable you to switch between the people’s faces.
• Rotating the zoom control to g (i) or f (h) further can change the
magnification ratio and the pictures will be zoomed in as usual.
48
Editing Pictures
The editing features described below are available. Use the camera to edit pictures
Editing function
Description
Create a copy of the current picture with enhanced brightness and
contrast, brightening dark portions of the picture.
Create a small copy of pictures suitable for use on web pages or as
e-mail attachments.
Enlarge the image or refine the composition and create a copy
containing only the portion visible in the monitor.
B Notes on In-camera Editing
• Only pictures taken with the COOLPIX L24 can be edited with this camera.
• When using a different model of digital camera, pictures edited with this camera may not be
displayed properly and may not be able to be transferred to a computer.
• Editing functions are not available when there is not enough free space in the internal memory or
on the memory card.
C Restrictions on Picture Editing
The following limitations apply when editing pictures that were created by editing.
Copies Created By:
D-Lighting
Can Be Edited By:
Small picture and crop can be used.
Small picture
Crop
Additional editing is not possible.
• Copies created by the editing functions cannot be edited again using the same edit function.
• To use D-Lighting together with small picture or crop, use the D-Lighting first.
D Original Pictures and Edited Copies
• Copies created with editing functions are not deleted if the original pictures are deleted. The
original pictures are not deleted if copies created with editing functions are deleted.
• Edited copies are stored with the same recording date and time as the original.
• Print set (A 68) and Protect (A 104) settings configured for original pictures are not reflected in
their edited copies.
49
Editing Pictures
Enhancing Brightness and Contrast: D-Lighting
Create a copy of the current image with enhanced brightness and contrast,
brightening dark portions of the picture. Enhanced copies are saved as separate
files.
1
Select the desired picture from full-frame
and press d.
The playback menu will be shown.
2
Use the multi selector to choose
I D-Lighting and press k.
Playback menu
D-Lighting
Print set
The original version will be shown on the left and the
edited version will be shown on the right.
Slide show
Delete
Small picture
Exit
3
Choose OK and press k.
A new copy with enhanced brightness and contrast is
created.
D-Lighting
To cancel, select Cancel and press k.
OK
Cancel
D-Lighting copies can be recognized by the c icon
displayed during playback.
15/05/2011 15:30
0004. JPG
4
4
D More Information
50
Editing Pictures
Resizing Pictures: Small Picture
Create a small copy of the current picture. Suitable for uploading to web sites or
sending by e-mail. The following sizes are available: l 640×480, m 320×240,
and n 160×120.
Small copies are saved as JPEG files with a compression ratio of 1:16.
1
2
Select the desired picture from full-frame
and press d.
The playback menu will be shown.
Use the multi selector to choose g Small
picture and press k.
Playback menu
D-Lighting
Print set
Slide show
Delete
Small picture
Exit
3
4
Choose the desired copy size and press k.
Small picture
640×480
320×240
160×120
Exit
Choose Yes and press k.
A new, smaller copy is created.
Creattee ssmmaalll picture file?
To cancel, select No and press k.
The copy is displayed with a gray frame.
Yes
No
D More Information
51
Editing Pictures
Creating a Cropped Copy: Crop
This function is only available when u is displayed in the monitor with
1
Rotate the zoom control to g (i) in full-frame playback mode to zoom
in on the image.
To crop a picture displayed in “tall” (portrait) orientation, zoom
in on the picture until the black bars displayed on the both sides
of the monitor disappear.
The cropped picture will be displayed in landscape orientation.
If you want to crop the portrait image in the captured position,
portrait image to landscape before cropping it, and then return
the image to the captured position.
2
Refine copy composition.
Rotate the zoom control to g (i) or f (h) to adjust the
zoom ratio.
Press the multi selector H, I, J or K to scroll the
picture until only the portion you want to copy is visible
in the monitor.
×
4.0
3
4
Press d.
Use the multi selector to select Yes and press
k.
A new picture, containing only the portion visible in the
Saavvee tthhis image as
displayed?
monitor, is created.
To cancel, select No and press k.
Yes
No
C About the Size of the Original Image
The smaller the cropped area of the image, the smaller of the cropped image size (number of pixels).
When the image is cropped and the size of the cropped copy is 320 × 240 or 160 × 120, the image is
displayed with a gray border on the playback screen, and the small picture icon l or m is displayed
on the left of the playback screen.
D More Information
52
Movies
Recording Movies
To shoot movies with sound recorded via the built-in microphone, select shooting
mode and follow the steps below.
1
Press A in shooting mode to display
the shooting-mode selection menu
and use the multi selector H and I
to select D, then press k.
Movie
The maximum length of the movie that can
be recorded is displayed in the monitor
memory on the memory card, the maximum size of a single movie is 2 GB, and the
maximum length of a single movie is 29 minutes.
2
Press the shutter-release button all the
way down to start recording.
Camera focuses on subject in center of frame.
A progress bar at the bottom of the monitor
shows the amount of recording time remaining.
To end recording, press the shutter-release
button all the way down a second time.
4s
If recording time runs out, recording stops automatically.
B Recording Movies
• The camera focuses when the shutter-release button is pressed halfway, and the focus remains
locked while the shutter-release button is pressed halfway. Focus is locked while recording.
• Optical zoom cannot be applied while movies are recorded. Digital zoom cannot be used just
before recording a movie, but up to 2× digital zoom can be applied while movies are recorded.
Avoiding bright objects such as the sun, reflections of the sun, and electric lights is recommended
to avoid smear effects.
• When recording or playing back movies, colored stripes (interference patterns or moire) may appear
on subjects that have a regular, repeating grid, such as pattern of weave in cloths or windows in a
building, depending on the shooting distance or zoom ratio. This phenomenon occurs when the
subject’s pattern interferes with the camera sensor grid, and it does not indicate a malfunction.
B While the Camera is Saving Movies
When movie recording stops, the shooting screen is displayed after the movie has been completely
saved. Do not open the battery-chamber / memory card slot cover.
Removing the memory card or the battery while a movie is being saved may result in loss of the
movie data or damage to the camera or the memory card.
C Options Available When Shooting Movies
begins. Settings cannot be changed while recording a movie. Flash, self-timer, and exposure
compensation cannot be used.
53
The Movie Menu
Movie options setting can be changed from the movie menu.
Displaying the Movie Menu
Press A in shooting mode to display the shooting-mode selection menu and set
Press d to display the movie menu.
Movie options
TV movie 640
Small size 320
10s
Exit
• To exit the menu, press d.
D Selecting Movie Options
The movie menu offers the options shown below.
Option
Resolution and Frame Rate
Resolution: 640×480
I TV movie 640
(default setting)
Frame rate: About 30 frames per second
Resolution: 320×240
Frame rate: About 30 frames per second
S Small size 320
C Movie Options and Maximum Movie Length
Internal memory
(Approx. 17 MB)
Option
Memory card (4 GB)*
45 min
3 h
I TV movie 640
(default setting)
9 s
38 s
S Small size 320
All figures are approximate. Maximum movie length or frames varies with make of memory card.
* Regardless of the remaining memory on the memory card, the maximum size of a single movie is
2 GB, and the maximum length of a single movie is 29 minutes. The maximum recording time that
is displayed is the maximum recording time for one movie.
D More Information
54
Movie Playback
a movie, display it in full-frame playback mode and
press k.
15/05/2011 15:30
0010. AVI
10s
Use the zoom control g/f to adjust playback volume.
Pausing
Playback controls appear at the top of the monitor.
Press the multi selector J or K to choose a control,
then press k to perform the selected operation. The
following operations are available.
4s
During
playback
Volume
indicator
To
Rewind
Press
Description
Rewind movie. Playback resumes when k is released.
K
Advance
Pause
End
L
O
Q
Advance movie. Playback resumes when k is released.
Pause playback. The following operations can be performed
while playback is paused.
Rewind movie by one frame. Rewind continues while k
is pressed.
M
Advance movie by one frame. Advance continues while
k is pressed.
N
P
Resume playback
End playback and return to full-frame playback.
Deleting Movie Files
Press l when displayed in full-frame playback mode
playback mode. A confirmation dialog is displayed.
Choose Yes and press k to delete the movie, or
choose No and press k to return to the normal
playback display without deleting the movie.
Erase 1 image?
Yes
No
55
Connecting to Televisions, Computers and Printers
Connecting to a TV
Connect the camera to a television using an optional audio video cable (AV cable)
1
2
Turn off the camera.
Connect the camera to the TV.
Connect the yellow plug to the video-in jack on the TV, and the white plug to the audio-
in jack.
Yellow
White
3
4
Tune the television to the video channel.
See the documentation provided with your television for details.
Hold down c to turn on the camera.
The camera enters playback mode, and the pictures
taken will be displayed on the television.
While connected to the TV, the camera monitor will
remain off.
B Connecting an AV Cable
When connecting the AV cable, be sure that the camera connector is oriented correctly. Do not use
force when connecting the AV cable to the camera. When disconnecting the AV cable, do not pull
the connector at an angle.
B Video Mode
Be sure that the camera’s video mode setting conforms to the standard used by your television. The
56
Connecting to a Computer
Use the supplied USB cable to connect the camera to a computer and copy
(transfer) images to the computer.
Before Connecting the Camera
Install the Software
Use the supplied ViewNX 2 CD and install the following software on the computer.
• ViewNX 2: Use the image transfer feature “Nikon Transfer 2” to save images that
were captured with the camera on the computer. Saved images can be viewed
and printed. Image and movie editing features are also supported.
• Panorama Maker 5: This software can join a series of images to create a single
panorama image.
For more information on installing the software, refer to the Quick Start Guide.
Compatible Operating Systems
Windows
Windows 7 Home Basic/Home Premium/Professional/Enterprise/Ultimate,
Windows Vista Home Basic/Home Premium/Business/Enterprise/Ultimate (Service
Pack 2), or Windows XP Home Edition/Professional (Service Pack 3)
Macintosh
Mac OS X (version 10.4.11, 10.5.8, 10.6.4)
Refer to the Nikon website for the latest information on operating system
compatibility.
B Notes on Power Source
• When connecting the camera to a computer to transfer images, use fully charged batteries to
prevent the camera from turning off unexpectedly.
• To power the camera continuously for extended periods, use an AC Adapter EH-65A (available
Failure to observe this precaution could result in overheating or in damage to the camera.
57
Connecting to a Computer
Transferring Images from a Camera to a Computer
1
2
3
Start the computer to which ViewNX 2 was installed.
Be sure that the camera is off.
Connect the camera to the computer using the supplied USB cable.
Be sure that connectors are properly oriented. Do not attempt to insert connectors at an
angle, and do not use force when connecting or disconnecting the USB cable.
4
Turn on the camera.
The power-on lamp will light. The camera monitor will
remain off.
B Connecting the USB Cable
The connection may not be recognized if the camera is connected to the computer via a USB hub.
58
Connecting to a Computer
5
Start the ViewNX 2 image transfer feature “Nikon Transfer 2” installed
on the computer.
•
Windows 7
When the Devices and Printers K L24 screen is displayed, click Change program
under Import pictures and videos. Select Import File using Nikon Transfer 2 in
the Change program dialog and click OK.
Double-click Import File on the Devices and Printers K L24 screen.
•
•
Windows Vista
When the AutoPlay dialog is displayed, click Import File using Nikon Transfer 2.
Windows XP
When the action selection dialog is displayed, select Nikon Transfer 2 Import File,
and click OK.
•
Mac OS X
Nikon Transfer 2 will start automatically when the camera is connected to the
computer if Yes was selected in the Auto-Launch setting dialog when Nikon
Transfer 2 was first installed.
•
•
If charge for the batteries inserted into the camera is low, the computer may not
recognize the camera. If the camera is not recognized, images will not be transferred.
If there are a large number of images on the memory card, it may take some time for
Nikon Transfer 2 to start.
6
Confirm that the source device is displayed in the transfer options
Source panel and click Start Transfer.
Source device
Start Transfer button
Any images that have not been transferred to the computer will be transferred (default
setting of ViewNX 2).
59
Connecting to a Computer
ViewNX 2 starts automatically when the transfer is complete (default setting of ViewNX
2). Transferred images can be viewed.
For more information on using ViewNX 2, refer to the ViewNX 2 help information
Disconnecting the Camera
Do not turn off the camera or disconnect the camera from the computer during
transfer.
When transfer is complete, turn off the camera and disconnect the USB cable.
60
Connecting to a Computer
C Transferring Images Using a Computer’s Card Slot or a Commercially-
available Card Reader
When the memory card is inserted into a computer’s card slot or into a commercially-available card
reader, the images can be transferred using “Nikon Transfer 2”, the image transfer feature of ViewNX 2.
• Make sure that the memory card being used is supported by the card reader or other card reading
device.
• To transfer images, insert the memory card into the card reader or card slot and follow the
• To transfer images saved in the camera’s internal memory, the images must first be copied to a
D Starting ViewNX 2 or Nikon Transfer 2 Manually
Windows
Choose Start menu > All Programs > ViewNX 2 > ViewNX 2.
Double-clicking the ViewNX 2 shortcut icon on the desktop will also start ViewNX 2.
Mac OS X
Open the Applications folder, open the Nikon Software > ViewNX 2 folders in that order, and
then double-click the ViewNX 2 icon. Clicking the ViewNX 2 icon on the Dock will also start
ViewNX 2.
Click Transfer in the ViewNX 2 screen to start Nikon Transfer 2.
D Viewing ViewNX 2 Help Information
For more information on ViewNX 2 or Nikon Transfer 2, start ViewNX 2 or Nikon Transfer 2 and select
ViewNX 2 Help from the Help menu.
D Panorama Creation with Panorama Maker 5
panorama photo with Panorama Maker 5.
• Panorama Maker 5 can be installed on a computer using the supplied ViewNX 2 CD.
• After installation is complete, follow the procedure described below to start Panorama Maker 5.
Windows
Choose Start menu>All Programs>ArcSoft Panorama Maker 5>Panorama Maker 5.
Mac OS X
Open Applications and double-click the Panorama Maker 5 icon.
• For more information on using Panorama Maker 5, refer to the on-screen instructions and help
information contained in Panorama Maker 5.
D Image File Names and Folder Names
61
Connecting to a Printer
to the printer and print pictures without using a computer.
Take pictures
Select pictures for printing
using Print set option
Print pictures one at a
Turn camera off and disconnect USB cable
B Note on Power Source
When connecting the camera to a printer, use a fully charged batteries to prevent the camera from
turning off unexpectedly.
To power the camera continuously for extended periods, use an AC Adapter EH-65A (available
Failure to observe this precaution could result in overheating or in damage to the camera.
D Printing Pictures
In addition to printing pictures transferred to a computer from your personal printer and printing
over a direct camera-to-printer connection, the following options are also available for printing
pictures:
• Insert a memory card into a DPOF-compatible printer’s card slot
• Take a memory card to a digital photo lab
For printing using these methods, you can specify the pictures and the number of prints each using
62
Connecting to a Printer
Connecting the Camera and Printer
1
Turn off the camera.
2
3
Turn on the printer.
Check printer settings.
Connect the camera to the printer using the supplied USB cable.
4
Turn on the camera.
When connected correctly, the PictBridge startup
screen (1) is displayed in the camera monitor, then the
Print selection screen (2) is displayed.
1
2
Print selection
1 5 / 0 5
2 0 1 1
NO. 12
[
12]
B Connecting the Audio Video/USB Cable
When connecting the USB cable, be sure that the connectors are oriented correctly. Do not use force
when connecting the USB cable. When disconnecting the USB cable, do not pull the connector at an
angle.
63
Connecting to a Printer
Printing Pictures One at a Time
following the procedure below.
1
2
3
4
5
Use the multi selector to choose the desired
picture and press k.
Rotate the zoom control to f (h) to display 12
thumbnails, and to g (i) to switch back to full-frame
playback.
Print selection
1 5 / 0 5
2 0 1 1
NO. 12
[
12]
Choose Copies and press k.
PictBridge
Start print
Copies
Paper size
Exit
Choose the number of copies (up to nine) and
press k.
Copies
4
Exit
Choose Paper size and press k.
PictBridge
Start print
Copies
Paper size
Exit
Choose the desired Paper size and press k.
To specify paper size using printer settings, choose
Default in the paper size menu.
Paper size
Default
3.5×5 in.
5×7 in.
A4
100×150 mm
4×6 in.
Exit
64
Connecting to a Printer
6
7
Choose Start print and press k.
PictBridge
Start print
Copies
Paper size
Exit
Printing starts.
Monitor display returns to that shown in step 1 when
printing is complete.
Printing
0 0 2
/
0 0 4
To cancel before all copies have been printed, press k.
Cancel
Current print/ total
number of prints
Printing Multiple Pictures
following the procedure below.
1
2
When the print selection screen is displayed,
press d.
The Print menu is displayed.
Use the multi selector to choose Paper size
and press k.
Press d to exit the print menu.
Print menu
Print selection
Print all images
DPOF printing
Paper size
Exit
3
Choose the desired Paper size and press k.
To specify paper size using printer settings, choose
Default in the paper size menu.
Paper size
Default
3.5×5 in.
5×7 in.
A4
100×150 mm
4×6 in.
Exit
65
Connecting to a Printer
4
Choose Print selection, Print all images or
DPOF printing and press k.
Print menu
Print selection
Print all images
DPOF printing
Paper size
Exit
Print selection
Select the images (up to 99) and the number of
copies (up to nine) of each image.
Print selection
10
Press the multi selector J or K to select pictures,
and press H or I to set the number of copies
for each.
Pictures selected for printing can be recognized
by the check mark y and the numeral
indicating the number of copies to be printed.
Pictures for which no copies have been specified
will not be printed.
Back
Rotate the zoom control to g (i) to switch to
full-frame playback. Rotate the zoom control to
f (h) to switch back to thumbnail display.
Press k when setting is complete.
When the menu shown on the right is displayed,
select Start print and press k to start printing.
Choose Cancel and press k to return to the
print menu.
Print selection
0 1 0 prints
Start print
Cancel
Exit
Print all images
All pictures stored in the internal memory, or on the memory card, are printed
one at a time.
When the menu shown on the right is displayed,
Print all images
select Start print and press k to start printing.
Choose Cancel and press k to return to the
0 1 2 prints
print menu.
Start print
Cancel
Exit
66
Connecting to a Printer
DPOF printing
•
When the menu shown on the right is
displayed, select Start print and press k to
start printing. Choose Cancel and press k to
return to the print menu.
DPOF printing
prints
0 1 0
Start print
View images
Cancel
Exit
•
To view the current print order, choose View
images and press k. To print pictures, press
k again.
View images
1 0
Back
5
Printing starts.
Monitor display returns to the print menu (step 2) when
printing is complete.
Printing
0 0 2
/
0 1 0
To cancel before all copies have been printed, press k.
Cancel
Current print/ total
number of prints
C Paper Size
The camera supports the following paper sizes: Default (the default paper size for the current
printer), 3.5 × 5 in., 5 × 7 in., 100 × 150 mm, 4 × 6 in., 8 × 10 in., Letter, A3, and A4. Only sizes
supported by the current printer will be displayed. To specify paper size using printer settings,
choose Default in the paper size menu.
67
Creating a DPOF Print Order: Print Set
Before printing images saved on a memory card using one of the methods listed
below, you can create a digital “print order” that specifies which images should be
printed and how many copies of each image should be printed, and save this
information on the memory card.
•
Printing with a DPOF-compatible (
• Printing using a digital photo lab that supports DPOF.
126) printer that features a memory card slot.
create the print order for images saved in the internal memory and print images
according to the print order.)
1
Press d in playback mode.
The playback menu is displayed.
2
Use the multi selector to choose Print set and
press k.
Playback menu
D-Lighting
Print set
Slide show
Delete
Small picture
Exit
3
4
Choose Select images and press k.
Print set
Select images
Delete print set
Exit
Choose the pictures (up to 99) and the
number of copies (up to nine) for each.
Print selection
Press the multi selector
J
or
K
to choose the desired
pictures. Press or
H
I
to set the number of copies for each.
Pictures selected for printing can be recognized by the
check mark and the numeral indicating the number of
copies to be printed. Pictures for which no copies have
been specified will not be printed.
Back
Rotate the zoom control to g (i) to switch to full-frame playback. Rotate the zoom
control to f (h) to switch back to thumbnail display.
Press k when setting is complete.
68
Creating a DPOF Print Order: Print Set
5
Choose whether or not to also print shooting
date and photo information.
Print set
Done
Choose Date and press k to print date of recording on
all pictures in the print order.
Date
Info
Choose Info and press k to print photo information
(shutter speed and aperture) on all pictures in the print
order.
Exit
Choose Done and press k to complete the print order
and exit.
Pictures selected for printing are indicated by the w
icon displayed during playback.
15/05/2011 15:30
0004. JPG
4
4
B Notes on Printing Shooting Date and Photo Information
• When the Date and Info options are enabled in the print set menu, shooting date and photo
printing of shooting date and photo information is used.
• Photo information cannot be printed when the camera is connected directly to a printer, via the
• Date and Info are reset each time the print set menu is displayed.
• The date and time printed on pictures with DPOF printing when
Date in the Print set menu is enabled, are those recorded with
the picture when it was taken. Date and time printed using this
option are not affected when the camera’s date and time setting
are changed from the setup menu after pictures are recorded.
C Deleting All Print Orders
15..055..22001111
Choose Delete print set in step 3 of the print set procedure and
press k to delete print orders for all pictures.
D Date Imprint
The shooting date and time can be imprinted in pictures at the time of shooting by using Date
printed, even if Print set is enabled with date selected in the print set screen.
69
Shooting, Playback and Setup Menus
Shooting Options: The Shooting Menu
following options.
A
Image mode
Choose image size and quality. Also available when using other shooting modes
(except movie mode).
B
C
F
White balance
Match white balance to the light source.
Continuous
Change settings to Continuous or BSS (best shot selector).
Color options
Make colors more vivid or record pictures in monochrome.
B Camera settings that cannot be applied at the same time
70
Shooting Options: The Shooting Menu
A Image mode
Pictures taken with a digital camera are recorded as image files. The size of the
files, and with it the number of images that can be recorded, depends on the size
and quality of the images. Before shooting, choose an image mode according to
how you plan to use the picture.
Setting
Size (pixels)
Description
Highest quality; suitable for enlargements
or high-quality prints. The compression
ratio is approximately 1:4.
Q
R
4320×3240P
4320×3240
4320×3240
(default setting)
4320×3240
Best choice in most situations. The
R
L
3264×2448
2592×1944
3264×2448
2592×1944
compression ratio is approximately 1:8.
Smaller size allows more pictures to be
saved. The compression ratio is
approximately 1:8.
M
N
2048×1536
1024×768
2048×1536
1024×768
Suited to display on a computer monitor.
The compression ratio is approximately 1:8.
Suited to full-screen display on a 4:3
television, or distribution by e-mail or the
web. The compression ratio is
approximately 1:8.
O
P
640×480
640×480
Pictures with an aspect ratio of 16:9 can be
taken. The compression ratio is
approximately 1:8.
3968×2232
3968×2232
The icon for the current setting is displayed in the monitor in shooting and
72
Shooting Options: The Shooting Menu
C Image mode
• If the image mode setting is changed, the new image mode setting is also applied to other
shooting modes (except movie mode).
C Number of Exposures Remaining
The following table lists the approximate number of pictures that can be stored in internal memory
and on a 4 GB memory card. Note that the number of pictures that can be stored will differ
depending on the composition of the picture (due to JPEG compression). In addition, this number
may differ depending on the make of memory card, even if the capacity for the memory card is the
same.
*1
Internal memory
(Approx. 17 MB)
Memory card
(4 GB)
Print size (printed at
300 dpi; cm/in.)
Image mode
*2
Q
R
4320×3240P
2
430
36 × 27/14 × 10.5
36 × 27/14 × 10.5
4320×3240
(default setting)
4
860
R
L
M
N
O
P
3264×2448
2592×1944
2048×1536
1024×768
640×480
7
11
17
51
82
6
1520
2410
28 × 21/11 × 8
22 × 16/8.5 × 6.5
17 × 13/7 × 5
3860
11000
17700
1370
9 × 7/3.5 × 2.5
5 × 4/2 × 1.5
3968×2232
34 × 19/13 × 7.5
*1
If the number of exposures remaining is 10,000 or more, the number of exposures remaining
display shows 9999.
When the printer resolution is set to 300 dpi.
*2
Print sizes are calculated by dividing the number of pixels by printer resolution (dpi) and
multiplying by 2.54 cm (1 in.). However, at the same image size, pictures printed at higher
resolutions will print smaller than the size indicated, and those printed at lower resolutions will
print larger than the size indicated.
73
Shooting Options: The Shooting Menu
B White Balance
The color of light reflected from an object varies with the color of the light source.
The human brain is able to adapt to changes in the color of the light source, with
the result that white objects appear white whether seen in the shade, direct
sunlight, or under incandescent lighting. Digital cameras can mimic this
adjustment by processing images according to the color of the light source. This is
known as “white balance.”
Although the default setting, Auto can be used under most types of lighting, you
can apply the white balance setting suited to a particular light source to achieve
more accurate results.
a
Auto (default setting)
White balance automatically adjusted to suit lighting conditions. Best choice in
most situations.
b
Preset manual
Neutral-colored object used as reference to set white balance under unusual
c
d
e
f
g
Daylight
White balance adjusted for direct sunlight.
Incandescent
Use under incandescent lighting.
Fluorescent
Use under most types of fluorescent lighting.
Cloudy
Use when taking pictures under overcast skies.
Flash
Use with the flash mode.
The effects of the selected option can be previewed in the monitor. At settings
B White Balance
74
Shooting Options: The Shooting Menu
Preset Manual
Preset manual is used with mixed lighting or to compensate for light sources with
a strong color cast (for example, to make pictures taken under a lamp with a red
shade look as though they had been taken under white light).
1
2
Place a white or gray reference object under the lighting that will be
used during shooting.
multi selector to set White balance to
b Preset manual, then press k.
White balance
Auto
Preset manual
Daylight
Incanddescennt
The camera zooms in.
Fluoresscent
Cloudy
Exit
3
4
Choose Measure.
To apply the most recently measured value for preset
manual, choose Cancel and press k.
Preset manual
Cancel
Measure
Exit
Frame the reference object.
Preset manual
Cancel
Measure
Exit
Reference object frame
5
Press k.
The shutter is released and the new white balance value is set (no picture is recorded).
B Note on Preset Manual
The camera cannot measure a white balance value for when the flash fires. When shooting with the
flash, set White balance to Auto or Flash.
75
Shooting Options: The Shooting Menu
C Continuous
Change settings to Continuous or BSS (best shot selector).
Flash will be switched off for Continuous, BSS or Multi-shot 16, and focus, exposure
and white balance are fixed at the values for the first picture in each series.
U
V
Single (default setting)
One shot is taken each time shutter-release button is pressed.
Continuous
While the shutter-release button is held down all the way, the camera shoots up to
three images at a rate of about 0.7 frames per second (fps) (when image mode is set
to R 4320 × 3240).
D
W
BSS (Best Shot Selector)
The “best shot selector” is recommended when shooting with the flash off or the
camera zoomed in, or in other situations in which inadvertent motion can result in
blurred pictures.
When BSS is on, the camera takes up to 10 pictures while the shutter-release button
is held down. The sharpest picture in the series is automatically selected and saved.
Multi-shot 16
Each time the shutter-release button is pressed all the way
down, 16 pictures are shot at about 30 frames per second
(fps) and the camera arranges them in a single picture.
Images are captured with the image mode fixed at
L (image size is 2560×1920).
Digital zoom cannot be applied.
The icon for the current setting is displayed in the monitor when the camera is in
B Note on Continuous Shooting
• The maximum frame rate with continuous shooting may vary, depending upon the current image
mode setting, the memory card used, and shooting conditions.
B Note on BSS
BSS is best suited to situations where the subject is not moving. BSS may not produce the desired
results if the subject moves or if the composition is changed while the shutter-release button is
pressed all the way down.
76
Shooting Options: The Shooting Menu
B Note on Multi-shot 16
image. Avoiding bright objects such as the sun, reflections of the sun, and electric lights is
recommended to avoid smear effects.
F Color Options
Make colors more vivid or record pictures in monochrome.
n
o
p
q
r
Standard color (default setting)
Use for pictures exhibiting natural color.
Vivid color
Use to achieve a vivid, “photoprint” effect.
Black-and-white
Record pictures in black-and-white.
Sepia
Record pictures in sepia tones.
Cyanotype
Record pictures in cyan-blue monochrome.
The icon for the current setting is displayed in the monitor when the camera is in
effects of the current setting can be previewed in the monitor.
B Notes on Color Options
77
Shooting Options: The Shooting Menu
Camera Settings that Cannot Be Set at the Same Time
Certain settings in the shooting menu cannot be used with other functions.
Restricted Functions
Flash mode
Setting
Description
If set to Continuous, BSS, or Multi-
shot 16, the flash cannot be used.
When using Multi-shot 16, the digital
Digital zoom
Image mode
Continuous
zoom cannot be used.
When using Multi-shot 16, Image
mode is fixed at L (image size is
2560×1920).
When using the self-timer, the setting is
fixed at Single.
When using Black-and-white, Sepia,
or Cyanotype, the White balance
setting is fixed at Auto.
White balance
Motion detection
When Multi-shot 16 is selected,
Motion detection is not enabled.
78
Playback Options: The Playback Menu
The following functions are available in playback mode.
I
a
b
D-Lighting
Enhances brightness and contrast in dark portions of pictures.
Print set
Select pictures to print and the number of copies for each.
Slide show
View pictures stored in the internal memory or on a memory card in an automatic
slide show.
c
Delete
Delete pictures. Multiple pictures can be deleted with one operation.
Small picture
g
Create a small copy of the current picture.
Displaying the Playback Menu
Display the playback menu by pressing d.
Playback menu
D-Lighting
Print set
Slide show
Delete
Small picture
Exit
• To exit the playback menu, press d.
79
Playback Options: The Playback Menu
Selecting Multiple Pictures
The screen shown at right will be displayed in the
menus (shown below) when choosing pictures.
Erase selected images
Delete: Erase selected images
Back
Setup menu:
Welcome screen: Select an image
Follow the procedure described below to choose the pictures.
1
Press the multi selector J or K to choose the
desired picture.
Erase selected images
Only one picture can be selected for Rotate image and
Welcome screen. Proceed to step 3.
Rotate the zoom control to g (i) to switch to full-frame
playback. Rotate the zoom control to f (h) to switch
back to thumbnail display.
Back
2
3
Press H or I to select ON or OFF (or the
Erase selected images
number of copies).
When ON is selected, a check mark (y) is displayed in
the top left corner of the current picture. Repeat steps 1
and 2 to select additional pictures.
Back
To fix the selection of pictures, press k.
80
Playback Options: The Playback Menu
b Slide Show
Press c (playback mode) M d (playback menu) M b Slide show
View pictures stored in the internal memory or on a memory card in an automatic
slide show.
1
Use the multi selector to choose Start and
press k.
Slide show
Pause
To repeat the slide show automatically, enable Loop and
press k before choosing Start. The check mark (w) will
be added to the loop option when enabled.
Start
Loop
Exit
2
The slide show begins.
While the slide show is in progress, the following
operations can be performed:
•
During playback, press the multi selector K to display
the next image and J to display the previous image
(press and hold K or J to fast-forward or rewind,
respectively).
•
Press k to pause the slide show.
3
Choose End or Restart.
When the slide show ends or is paused, choose End and
press k to return to the playback menu, or choose
Restart to play the slide show again.
Pause
Restart
End
B Notes on Slide Show
• Even if Loop is selected, the monitor can continuously display the Slide Show for up to 30 minutes
81
Playback Options: The Playback Menu
c Delete
Press c (playback mode) M d (playback menu) M c Delete
Delete selected pictures or all pictures.
Erase selected images
Erase all images
Delete all pictures.
B Notes on Deletion
• Once deleted, pictures cannot be recovered. Transfer important images to a computer before
deletion.
82
Basic Camera Setup: The Setup Menu
The setup menu contains the following settings.
a
c
d
e
Menus
Select the method for displaying menus.
Welcome screen
Specify the welcome screen displayed when the camera is turned on.
Date
Set camera clock and choose home and destination time zones.
Monitor settings
Choose whether or not to display information in the monitor, whether or not
pictures are shown on the display for review after taking them, and set the
monitor brightness.
f
w
U
Date imprint
Imprint the shooting date and time on pictures.
Electronic VR
Specify the electronic vibration reduction setting for taking still pictures.
Motion detection
Set whether or not the camera automatically increases the shutter speed to
reduce blurring when motion is detected while shooting still pictures.
h
i
AF assist
Enable or disable AF-assist illumination.
Sound settings
Adjust sound settings.
k
Auto off
Set time before camera enters standby mode to conserve power.
Format memory/Format card
Format internal memory or memory card.
Language
l/m
n
Choose the language used for camera monitor display.
Video mode
o
d
Adjust settings for connection to a television.
Blink warning
Set whether or not to detect human subjects with eyes closed when shooting
pictures using face detection.
p
Reset all
Restore camera settings to their default values.
83
Basic Camera Setup: The Setup Menu
s
Battery type
Select the type of batteries used.
Protect
d
f
Protect selected pictures from accidental deletion.
Rotate image
Change the orientation of a picture.
Copy
h
r
Copy files between memory card and internal memory.
Firmware version
Display camera firmware version.
Displaying the Setup Menu
Display the menu screen and select z (Setup).
1
Press d to display the menu screen.
When using easy auto mode, scene mode, smart portrait
mode, or movie mode, press J on the multi selector
Easy auto mode
Image mode
Exit
2
3
Press the multi selector J to enter the menu.
You can now select a tab.
Easy auto mode
Image mode
Exit
Press H or I to select the z tab.
Set up
Menus
Welcome screen
Date
Monitor settings
Date imprint
Electronic VR
Exit
84
Basic Camera Setup: The Setup Menu
4
Press K or k.
You can now select an item from the setup menu.
Set up
Menus
Welcome screen
Date
Monitor settings
Date imprint
Electronic VR
To exit the setup menu, press the d or press J and
select another tab.
Exit
a Menus
Select the method for displaying menus.
Text (default setting)
Menus are displayed in list format.
Set up
Menus
Welcome screen
Date
Monitor settings
Date imprint
Electronic VR
Exit
Icons
All menu items can be displayed in a single page.
Menu names
Menus
Exit
85
Basic Camera Setup: The Setup Menu
c Welcome Screen
Specify the welcome screen displayed when the camera is turned on.
None (default setting)
The welcome screen is not displayed when the camera is turned on; the shooting
mode or playback mode screen is displayed.
COOLPIX
The welcome screen is displayed when the camera is turned on, then the shooting
mode or playback mode screen is displayed.
Select an image
An image captured with this camera is used as the welcome screen.
press k to register the image as the welcome screen.
•
As the selected image is stored in the camera, the image will appear in the
welcome screen even if the original picture is deleted.
•
pictures that are 320×240 or smaller after being edited using small picture
86
Basic Camera Setup: The Setup Menu
d Date
Set the camera clock.
Date
Set camera clock to current date and time.
Use the multi selector to set the date and time.
•
Highlight an item (day, month, year, hour, minute, and the order in which day,
month, and year are displayed): Press J or K.
•
•
Edit the highlighted item: Press H or I.
Finish setting: After selecting the order in which the day, month, and year are
Time zone
Set the home (w) time zone (district) or daylight saving time. When the destination
and the date and time in the selected region are recorded. Useful when travelling.
Setting Travel Destination Time Zone
1
Use the multi selector to choose Time zone
and press k.
Date
1 5 / 0 5 / 2 0 1 1
1 5 : 3 0
The Time zone menu is displayed.
Date
Time zone
Exit
2
Choose x Travel destination and press k.
The date and time displayed on the monitor changes
according to the region currently selected.
Time zone
1 5 / 0 5 / 2 0 1 1
London, Casablanca
1 5 : 3 0
Home time zone
Travel destination
Exit
87
Basic Camera Setup: The Setup Menu
3
Press K.
Time zone
1 5 / 0 5 / 2 0 1 1 1 5 : 3 0
London, Casablanca
The new city time zone menu is displayed.
Home time zone
Travel destination
Exit
4
Press J or K to select the travel destination
region (time zone).
When using the camera in an area where daylight saving
time is in effect, press H to adjust the camera’s time for
daylight saving time. W will be displayed in the top of the
monitor and the time will advance one hour. To turn off
the daylight saving time setting, press I.
1 1 : 3 0
- 0 4 : 0 0
EDT:
New York
Toronto
Lima
Back
Press k to enter the travel destination.
While the travel destination time zone is selected, the Z icon will be displayed in the
monitor when the camera is in shooting mode.
B The Clock Battery
The camera’s clock is powered by a clock battery that is independent of the batteries that powers
the camera. The clock battery charges when the main batteries are installed or an AC adapter is
connected, and can provide several days of backup power after about ten hours of charging.
C w (Home Time Zone)
• To switch to the home time zone, choose w in step 2 and press k.
• To change the home time zone, choose w in step 2 and perform steps 3 and 4, to set the home
time zone.
C
Daylight Saving Time
When the summer saving time begins or ends, turn the daylight saving time option on or off using
the home time zone display in Step 4.
D Imprinting the Date on Pictures
imprint is set, the shooting date and time can be imprinted on the image data when taking
pictures.
88
Basic Camera Setup: The Setup Menu
D Time Zones
The camera supports the time zones listed below.
For time zones not listed below, set the camera’s clock manually to local time using Date in the
setup menu.
UTC
+/-
UTC
+/-
Time zone
Time zone
Madrid, Paris, Berlin
-11 Midway, Samoa
-10 Hawaii, Tahiti
+1
+2
Athens, Helsinki, Ankara
Moscow, Nairobi, Riyadh, Kuwait,
Manama
-9
Alaska, Anchorage
+3
PST (PDT): Los Angeles, Seattle,
Vancouver
-8
-7
-6
-5
+4
+5
Abu Dhabi, Dubai
Islamabad, Karachi
MST (MDT): Denver, Phoenix, La Paz
CST (CDT): Chicago, Houston, Mexico
City
+5.5 New Delhi
EST (EDT): New York, Toronto, Lima
+6
+7
+8
+9
Colombo, Dhaka
-4.5 Caracas
Bangkok, Jakarta
-4
-3
-2
-1
Manaus
Beijing, Hong Kong, Singapore
Tokyo, Seoul
Buenos Aires, Sao Paulo
Fernando de Noronha
Azores
+10 Sydney, Guam
+11 New Caledonia
+12 Auckland, Fiji
0
London, Casablanca
89
Basic Camera Setup: The Setup Menu
e Monitor Settings
The following settings are available.
Photo info
Choose information displayed in monitor during shooting and playback mode.
Image review
•
On (default setting): Pictures are automatically displayed briefly immediately
after shooting.
•
Off: Pictures are not displayed after shooting.
Brightness
Choose from five settings for monitor brightness. The default setting is 3.
90
Basic Camera Setup: The Setup Menu
Photo Info
Select whether or not photo info is displayed.
Shooting mode
Playback mode
15/05/2011 15:30
0004. JPG
Show info
Auto info
4
4
4
The same information as in Show info is displayed. If no operations are
performed after a few seconds, the display will be the same as Hide
(default setting) info. The information is displayed again when an operation is
performed.
Hide info
1155//0055//22001111 1155::3300
0004. JPG
4
4
4
In the following shooting modes,
a framing grid appears to help
frame pictures, in addition to the
information displayed in Auto
info.
The current settings or operation
guide is displayed, as in Auto info
above.
Framing grid
• G Easy auto mode
• A Auto mode
In other shooting modes, the
same information as in Auto info
is displayed.
91
Basic Camera Setup: The Setup Menu
f Date Imprint
Imprint the shooting date and time on pictures. Date
can be printed from printers that do not support the
15..055..22001111
Off (default setting)
Date and time are not imprinted on pictures.
Date
The date is imprinted in the bottom right corner of pictures.
Date and time
The date and time is imprinted in the bottom right corner of pictures.
At settings other than Off, the icon for the current setting is displayed in the
B Date Imprint
• Imprinted dates form a permanent part of image data and cannot be deleted.
• Date imprint is disabled in the following situations.
- When using the Panorama assist scene mode
- When using movie mode
Choose N 1024×768 or larger when using date imprint.
C Date Imprint and Print Set
When pictures are printed from DPOF-compatible printers that can print date and photo
the pictures. In such a case, it is unnecessary to imprint date and time on pictures beforehand using
Date Imprint.
92
Basic Camera Setup: The Setup Menu
w Electronic VR
Choose whether to use electronic VR (vibration reduction) when taking still
pictures.
Auto
When all of the following conditions are met while taking still pictures, electronic VR
is applied and the effects of camera shake are reduced.
•
•
•
•
The flash is turned off or set to slow sync mode.
The shutter speed is slow.
The Continuous setting is set to Single.
When the subject is dark.
Off (default setting)
Electronic VR is disabled.
applied depending on shooting conditions.
B Notes on Electronic Vibration Reduction
• Electronic VR is disabled while the flash is used, except when using slow sync mode. Note that
• If the exposure period exceeds a certain period of time, Electronic VR will not function.
• Electronic VR cannot be used when using the following scene modes.
• The effectiveness of Electronic VR decreases as camera shake increases.
• Pictures taken using motion detection may be somewhat grainy.
93
Basic Camera Setup: The Setup Menu
U Motion Detection
Set whether or not the camera automatically increases the shutter speed to
reduce blurring when motion is detected while shooting still pictures.
Auto (default setting)
In order to reduce the effects of camera shake or subject movement, ISO
sensitivity and shutter speed are increased when the camera detects camera
shake or subject movement.
However, motion detection does not function in the following situations.
•
•
•
When flash mode is set to m (fill flash)
Off
Motion detection is not enabled.
The icon for the current setting is displayed in the monitor when the camera is in
speed, the motion detection indicator turns green. No icon is displayed when Off
is selected.
B Notes on Motion Detection
• Blurring caused by camera shake or subject movement may not be eliminated in some situations.
• Motion detection may not function if camera shake or subject movement is excessive, or if there is
insufficient lighting.
• The pictures taken may become somewhat grainy.
94
Basic Camera Setup: The Setup Menu
h AF Assist
Change settings for AF-assist illumination.
Auto (default setting)
AF-assist illumination will be used to assist the focus operation when the subject is
poorly lit. The illuminator has a range of about 1.9 m (6 ft. 3 in.) at the maximum
wide-angle position and 1.1 m (3 ft. 7 in.) at the maximum telescopic position.
However, the AF-assist illumination will not turn on in some scene modes even if
Off
Disable this function. The camera may be unable to focus if lighting is poor.
95
Basic Camera Setup: The Setup Menu
i Sound Settings
Adjust the following sound settings.
Button sound
Turn the button sound On or Off. When On (default setting) is selected, a beep
will sound once when operations are completed successfully, two times when the
focus has been locked, and three times when an error is detected, and welcome
sound is played when the camera is turned on.
Shutter sound
Choose shutter sound from On (default setting) or Off.
Even when set to On, the shutter sound is not heard in the following situations.
•
•
•
When using Continuous, BSS, or Multi-shot 16
When using Sports or Museum
When shooting movies
96
Basic Camera Setup: The Setup Menu
k Auto Off
When the camera is on and a period of time passes without any operations, the
When the camera enters standby mode, the power-on lamp flashes. If no
operations are performed within three minutes, the camera turns off.
Use this option to set the amount of time that passes before the camera enters
standby mode.
Auto off
Choose the time allowed to elapse before the camera enters standby mode if no
operations are performed from 30 s (default setting), 1 min, 5 min, and 30 min.
Sleep Mode
If On (default setting) is selected, the camera will enter standby mode when there
is no change in the brightness of the subject, even before the time selected in the
auto off menu has elapsed. The camera will enter sleep mode after 30 seconds
when Auto off is set to 1 min or less, or after 1 minute when Auto off is set to
5 min or more.
B Notes on Auto Off
The time allowed to elapse before the camera enters standby mode is fixed in the following cases:
• While menus are displayed: 3 minutes
• While slide show is in progress: Up to 30 minutes
C Canceling Standby Mode
Cancel standby mode and reactivate the monitor by pressing any of the following buttons.
• Power switch
• Shutter-release button
• A button
• c button
97
Basic Camera Setup: The Setup Menu
l Format Memory/m Format Card
Use this option to format the internal memory or a memory card.
Formatting Internal Memory
Format memory
All images will
To format the internal memory, remove the memory
card from the camera.
be deleted! OK?
The Format memory option appears in the setup
menu.
Format
No
Exit
Formatting a Memory Card
When the memory card is inserted in the camera, the
Format card option appears in the setup menu.
Format card
All images will
be deleted! OK?
Format
No
Exit
B Formatting Internal Memory and Memory Cards
• Formatting the internal memory or memory cards permanently deletes all data. Be sure to transfer
important pictures to a computer before formatting.
• Do not turn the camera off or open the battery-chamber/memory card slot cover during
formatting.
• The first time you insert the memory cards used in other devices into this camera, be sure to
format them using this camera.
98
Basic Camera Setup: The Setup Menu
n Language
Select the language used for camera monitor display.
Czech
Polish
Danish
Portuguese
Russian
German
(default setting)
Spanish
Greek
Finnish
Swedish
Turkish
French
Arabic
Indonesian
Italian
Simplified Chinese
Traditional Chinese
Japanese
Korean
Hungarian
Dutch
Norwegian
Thai
o Video Mode
Adjust settings for connection to a television. Choose from NTSC and PAL.
99
Basic Camera Setup: The Setup Menu
d Blink Warning
Choose whether or not blinking eyes are detected when using face detection
• G (easy auto) mode
•
On
When the camera detects that one or more human subjects have closed their eyes
shortly after recognizing the faces and shooting them, the Did someone blink?
screen will appear on the monitor. The face of the human subject that may have
closed his/her eyes is framed by a yellow border. In such a case, you can check the
Off (default setting)
Blink warning doesn’t take effect.
Operating the Did someone blink? Screen
The following operations are available while the Did
someone blink? screen is displayed.
Did someone blink?
If no operations are performed for a few seconds, the
screen automatically returns to the shooting mode
screen.
Exit
To
Use
g (i)
Description
Enlarge and display the face
of the person who blinked
Rotate the zoom control to g (i).
Switch to full-frame playback
f (h)
Rotate the zoom control to f (h).
If the camera detects more than one
human subjects with their eyes closed,
press HIJ K during the enlarged
display to switch over the face displayed.
Select the face to be
displayed
Delete the shot picture
Switch to shooting mode
l
Press l.
k
Press k or the shutter-release button.
100
Basic Camera Setup: The Setup Menu
p Reset All
When Reset is selected, the camera’s settings will be restored to their default
values.
Pop-up Menu
Option
Default value
Auto
Off
Off
0.0
Scene mode
Option
Default value
Default value
Portrait
Center
Movie Menu
Option
TV movie 640
Shooting Menu
Option
Default value
R 4320×3240
Auto
Single
Standard color
101
Basic Camera Setup: The Setup Menu
Setup Menu
Option
Default value
Text
None
Auto info
On
3
Off
Off
Auto
Auto
On
On
30 s
On
Off
Others
Option
Default value
Default
memory. Numbering will continue from the lowest number available. To reset
• The following settings in the menus will remain unaffected even if Reset all is
performed.
Shooting menu:
Setup menu:
102
Basic Camera Setup: The Setup Menu
f Rotate Image
Set the picture orientation (vertical or horizontal frame) displayed on the camera
monitor after the pictures are taken.
Pictures can be rotated 90° clockwise or counterclockwise.
Pictures that were recorded in the portrait (vertical) orientation can be rotated up
to 180° in either direction.
Rotate image screen. Press the multi selector J or K to rotate the picture 90°.
Rotate image
Rotate image
Rotate image
Back
Rotate
Back
Back
Rotate
Rotate
Rotate 90°
counterclockwise
Rotate 90°
clockwise
Press k to select the displayed direction and the vertical / horizontal position data
will be recorded on the picture.
105
Basic Camera Setup: The Setup Menu
h Copy
Copy pictures between the internal memory and a memory card.
1
2
Select an option from the copy screen using
the multi selector and press k.
q: Copy pictures from internal memory to
Copy
memory card.
r: Copy pictures from memory card to internal
Exit
memory.
Choose the copy option and press k.
Selected images: Copy pictures selected from the
Camera to card
Selected images
All images
All images:
Copy all pictures.
Exit
B Notes on Copying Pictures
• JPEG- and AVI-format files can be copied. Files recorded in any other format cannot be copied.
• Pictures taken with another make of camera or that have been modified on a computer cannot be
copied.
D More Information
106
Technical Notes
Optional Accessories
Rechargeable Ni-MH batteries EN-MH2-B2 (set of two EN-MH2
batteries)*
1
Rechargeable
battery
Rechargeable Ni-MH batteries EN-MH2-B4 (set of four EN-MH2
1
batteries)*
Battery Charger MH-72 (includes two rechargeable Ni-MH batteries
1
EN-MH2)*
Battery charger
Battery Charger MH-73 (includes four rechargeable Ni-MH batteries
EN-MH2)*
1
AC Adapter EH-65A
<How to attach EH-65A>
1
1
AC adapter
2
2
AC Adapter EH-62B cannot be used.
USB Cable UC-E6
USB Cable
AV Cable
Audio/Video Cable EG-CP14
*1
To charge EN-MH2 batteries, use only Battery Charger MH-72 or MH-73. Do not use these
battery chargers to charge any other type of battery.
108
Optional Accessories
Approved Memory Cards
The following Secure Digital (SD) memory cards have been tested and approved
for use in this camera.
Memory cards with an SD Speed Class rating of 6 or faster are recommended for
recording movies. Movie recording may stop unexpectedly when memory cards
with a lower Speed Class rating are used.
SD memory
SDXC memory
2
SDHC memory card
3
card
card
1
SanDisk
TOSHIBA
Panasonic
Lexar
2 GB
4 GB, 8 GB, 16 GB, 32 GB
4 GB, 8 GB, 16 GB, 32 GB
64 GB
64 GB
1
1
1
2 GB
2 GB
2 GB
4 GB, 8 GB, 12 GB, 16 GB, 24 GB, 32 GB 48 GB, 64 GB
4 GB, 8 GB, 16 GB, 32 GB
–
1
2
If the memory card will be used with a card reader or similar device, check that device
supports 2 GB cards.
SDHC compliant.
If the memory card will be used with a card reader or similar device, check that
device supports SDHC.
SDXC compliant.
3
If the memory card will be used with a card reader or similar device, check that
device supports SDXC.
•
Contact the manufacturer for details on the above cards.
109
Image File and Folder Names
Pictures and movies are assigned file names as follows.
DSCN0001.JPG
Identifier (not shown on camera monitor)
Extension (signifies the file type)
Original still pictures, movies
Small copies
Still pictures
Movies
.JPG
.AVI
DSCN
SSCN
RSCN
FSCN
Cropped copies
D-Lighting copies
File number (assigned automatically in
ascending order, starting with “0001”)
• Files are stored in folders named with a folder number followed by a five-
character identifier: “P_” plus a three-digit sequence number for pictures taken
pictures (e.g. “100NIKON”). When the number of files within a folder reaches
9999, a new folder will be created. File numbers will be assigned automatically
starting with “0001.”
• Files copied using Copy > Selected images are copied to the current folder,
where they are assigned new file numbers in ascending order starting from the
largest file number in memory. Copy > All images copies all folders from the
source medium; file names do not change but new folder numbers are
assigned in ascending order, starting from the largest folder number on the
• Folders can hold up to 200 pictures; if a picture is taken when the current folder
contains 200 pictures, a new folder will be created by adding one to the current
folder number. If a picture is taken when the current folder is numbered 999
and contains 200 pictures or a picture numbered 9999, no further pictures can
110
Caring for the Camera
To ensure continued enjoyment of this Nikon product, observe the following
precautions when using or storing the device:
B Keep dry
The device will be damaged if immersed in water or subjected to high humidity.
B Do not drop
The product may malfunction if subjected to strong shock or vibration.
B Handle the lens and all moving parts with care
Do not apply force to the lens, lens cover, monitor, memory card slot or battery chamber. These
parts are easily damaged. Applying force to the lens cover could result in camera malfunction or
damage to the lens. Should the monitor break, care should be taken to avoid injury caused by
broken glass and to prevent the liquid crystal from the display touching the skin or entering the eyes
or mouth.
B Do not point the lens at strong light sources for extended periods
Avoid pointing the lens at the sun or other strong light sources for extended periods when using or
storing the camera. Intense light may cause deterioration of the image sensor, producing a white
blur effect in photographs.
B Keep away from strong magnetic fields
Do not use or store this device in the vicinity of equipment that generates strong electromagnetic
radiation or magnetic fields. Strong static charges or the magnetic fields produced by equipment
such as radio transmitters could interfere with the monitor, damage data stored on the memory
card, or affect the product’s internal circuitry.
B Avoid sudden changes in temperature
Sudden changes in temperature, such as when entering or leaving a heated building on a cold day,
can cause condensation to form inside the device. To prevent condensation, place the device in a
carrying case or a plastic bag before exposing it to sudden changes in temperature.
B Turn the product off before removing or disconnecting the power source
Do not remove the batteries while the product is on, or while images are being recorded or deleted.
Forcibly cutting power in these circumstances could result in loss of data or in damage to product
memory or internal circuitry.
111
Caring for the Camera
C The Battery
• Check the battery level when taking the camera out, and replace the batteries if necessary (A 18).
If possible, carry spare batteries when taking pictures on important occasions.
• When recharging rechargeable batteries, do not recharge batteries that contain a different
amount of charge, or batteries of different model numbers.
• When charging EN-MH2 batteries using Battery Charger MH-72, charge two batteries at a time.
When charging EN-MH2 batteries using Battery Charger MH-73, charge two or four batteries at a
time. To charge EN-MH2 batteries, use only Battery Charger MH-72 or MH-73. Do not use these
battery chargers to charge any other type of battery.
• Do not use any battery charger other than the MH-70/71 to recharge EN-MH1 batteries. Do not
use the MH-70/71 to charge any batteries other than EN-MH1 batteries. Set the Battery type
• Battery capacity tends to decrease on cold days. Be sure that the batteries are fresh before heading
outside to take pictures in cold weather. Keep spare batteries in a warm place and exchange as
necessary. Once warmed, a cold battery may recover some of its charge.
• Dirt on the battery terminals can prevent the camera from functioning.
• Used batteries are a valuable resource. Please recycle used batteries in accordance with local
regulations.
112
Caring for the Camera
Cleaning
Avoid touching glass parts with your fingers. Remove dust or lint with a blower
(typically a small device with a rubber bulb attached to one end that is
pumped to produce a stream of air out the other end). To remove fingerprints
or other stains that cannot be removed with a blower, wipe the lens with a soft
cloth, using a spiral motion that starts at the center of the lens and working
toward the edges. If this fails, clean the lens using a cloth lightly dampened
with commercial lens cleaner.
Lens
Remove dust or lint with a blower. To remove fingerprints and other stains,
clean the monitor with a soft, dry cloth, being careful not to apply pressure.
Monitor
Body
Use a blower to remove dust, dirt or sand, then wipe gently with a soft, dry
cloth. After using the camera at the beach or seaside, wipe off any sand or salt
with a dry cloth lightly dampened with fresh water, then dry thoroughly. Note
that foreign matter inside the camera could cause damage not covered by the
warranty.
Do not use alcohol, thinner, or other volatile chemicals.
113
Caring for the Camera
Storage
Turn the camera off when not in use. Check that the power-on lamp is off before
putting the camera away. Remove the batteries if the camera will not be used for
an extended period. Do not store the camera with naphtha or camphor moth
balls, or in any of the following locations:
• Next to equipment that produces strong electromagnetic fields, such as
televisions or radios
• Exposed to temperatures below –10 °C (14 °F) or above 50 °C (122 °F)
• Poorly ventilated or subject to humidities of over 60%
To prevent mold or mildew, take the camera out of storage at least once a month.
Turn the camera on and release the shutter a few times before putting the camera
away again.
C Notes on the Monitor
• The monitor may contain a few pixels that are always lit or that do not light. This is a characteristic
common to all TFT LCD displays, and does not indicate a malfunction. Images recorded using the
product will not be affected.
• When framing bright subjects, vertical comet-like streaks that whiten toward either end may
appear in the display. This phenomenon, known as “smear”, does not indicate a malfunction.
In shooting modes other than movie mode, smear has no effect on the images that are recorded.
• Images in the monitor may be difficult to see under bright lighting.
• The monitor is lit by an LED backlight. Should the monitor begin to dim or flicker, contact your
Nikon-authorized service representative.
C Note on Smear
White or colored streaks may be visible when bright subjects are framed in the monitor. This
phenomenon, known as “smear,” occurs when extremely bright light strikes the image sensor; it is
characteristic of image sensors and does not indicate a malfunction. Smear may also take the form of
partial discoloration in the monitor during shooting. It does not appear in images recorded with the
camera except in the cases of movies and of images recorded with Multi-shot 16 selected for
Continuous. When shooting in these modes, we recommend that you avoid bright subjects such
as the sun, reflected sunlight, and electric lights.
114
Error Messages
The following table lists the error messages and other warnings displayed in the
monitor, as well as the solutions for dealing with them.
Display
O (blinks)
Problem
Clock not set.
Solution
A
Set clock.
B
Battery running low.
Battery exhausted.
Camera cannot focus.
Prepare to change the
batteries.
N
Replace batteries.
Battery exhausted.
Q (blinks red)
•
•
Refocus.
Use focus lock.
P
Camera cannot perform
other operations until
recording is complete.
Wait until message clears
from display automatically
when recording is
Please wait for the
camera to finish
recording.
complete.
N
Write-protect switch is in
“write” position.
Memory card is write “lock” position.
protected.
P
Error accessing memory
card.
•
•
Use approved card.
Check that connectors
are clean.
This card cannot be
used.
•
Confirm that memory
card is correctly inserted.
P
This card cannot be
read.
P
Memory card has not been All data saved on the
Card is not formatted. formatted for use in
memory card will be
deleted. If there is any data
on the card that you want
to keep, select No, and
backup the data to a
computer before
Format card?
COOLPIX L24.
Yes
No
formatting the memory
card. To format the memory
card, select Yes and press
k.
N
Memory card is full.
•
Choose smaller image
mode.
Out of memory.
•
Delete pictures.
•
•
Remove memory card
and use internal memory.
115
Error Messages
Display
Problem
Solution
A
P
Error occurred while
recording picture.
memory card.
Image cannot be
saved.
numbers.
or format the internal
memory/memory card.
Picture cannot be used for The following pictures
welcome screen.
cannot be used.
•
Pictures taken at an
Image mode setting of
P 3968×2232
Pictures created using
the small picture or crop
functions that are 320 ×
240 or smaller in size
•
There is not enough
memory to copy the
picture.
Delete pictures from
destination.
N
You are trying to edit a
picture that cannot be
edited.
are required for editing.
Image cannot be
modified.
N
Time out error while
faster write speed.
Cannot record movie. recording movie.
N
No pictures in the internal Remove memory card to
Memory contains no
images.
memory or memory card.
play back pictures from
internal memory.
N
File not created with
File cannot be viewed on
this camera. View file using
the computer or any other
devices which was used to
create or edit this file.
–
File contains no image COOLPIX L24.
data.
N
Picture is protected.
Disable protection.
This image cannot be
deleted.
N
Destination in same time
Travel destination is in zone as home.
the current time zone.
–
Lens error
Q
Lens error.
Turn camera off and then
on again. If error persists,
contact retailer or Nikon-
authorized service
representative.
116
Error Messages
Display
Problem
Solution
A
P
USB cable disconnected
USB cable.
Communications error during printing.
System error
Q
Error has occurred in
camera’s internal circuitry. and reinsert batteries, and
turn camera on. If error
Turn camera off, remove
persists, contact retailer or
Nikon-authorized service
representative.
PR
Printer error: check
printer status.
Running out of ink or
printer error.
Check printer. After
checking the ink or solving
the problem, select
–
Resume and press k to
*
resume printing.
PR
Printer error:
check paper
Specified size of paper is
not loaded in printer.
Load the specified paper,
–
–
–
–
–
–
select Resume and press
*
k to resume printing.
PR
Printer error:
paper jam
Paper has jammed in the
printer.
Eject the jammed paper,
select Resume and press
*
k to resume printing.
PR
Printer error:
out of paper
No paper is loaded in
printer.
Load the specified paper,
select Resume and press
*
k to resume printing.
PR
Printer error:
check ink
Ink error.
Check ink, select Resume
and press k to resume
*
printing.
PR
Printer error:
out of ink
Ink cartridge is empty.
Replace ink, select Resume
and press k to resume
*
printing.
PR
Printer error:
file corrupt
An error caused by the
image file has occurred.
Select Cancel and press k
to cancel printing.
* See the documentation provided with your printer for further guidance and
information.
117
Troubleshooting
If the camera fails to function as expected, check the list of common problems
below before consulting your retailer or Nikon-authorized service representative.
Refer to the page numbers in the right-most column for more information.
Display, Settings and Power Supply
Problem
Monitor is blank
Cause/Solution
A
•
•
•
Camera is off.
Battery exhausted.
Standby mode for saving power: press the
shutter-release button halfway.
•
•
•
charged.
cable.
Camera and TV are connected via AV cable.
Monitor is hard to read
•
•
Adjust monitor brightness.
Monitor is dirty. Clean monitor.
Camera turns off without
warning
•
•
Battery exhausted.
Camera has turned off automatically to save
power.
•
•
Battery is cold.
Date and time of recording are
not correct
Pictures taken while the clock is not set will
have a time stamp of “00/00/0000 00:00”
movies will be dated “01/ 01/2011 00:00.” (The
“Date not set” indicator blinks during shooting
to indicate the clock is not set.) Set the correct
date and time using Date in the setup menu.
Check camera clock regularly against more
accurate timepieces and reset as required.
•
No indicators displayed in
monitor
Hide info is selected for Photo info.
Select Show info.
Date imprint not available
Camera clock has not been set.
Date not appearing on pictures Date imprint is disabled in the following
even when Date imprint is
enabled
situations.
•
When the scene mode is set to Panorama
assist
•
Movies
Camera settings reset
restored to their default values.
118
Troubleshooting
Electronically Controlled Cameras
In extremely rare instances, unusual characters may appear in the monitor and the
camera may stop functioning. In most cases, this phenomenon is caused by a
strong external static charge. Turn the camera off, remove and replace the battery,
then turn the camera on again. In the event of continued malfunction, contact
your retailer or Nikon-authorized service representative. Note that disconnecting
the power source as described above may result in the loss of any data not
recorded to internal memory or the memory card at the time the problem
occurred. Data already recorded will not be affected.
Shooting
Problem
Cause/Solution
A
No picture taken when shutter-
release button is pressed.
•
•
•
•
When camera is in playback mode, press A.
When menus are displayed, press d.
Battery exhausted.
When flash lamp blinks, flash is charging.
Camera cannot focus.
Pictures are blurred.
•
The intended subject is one with which
autofocus does not perform well.
Set AF assist in the setup menu to Auto.
Focus error. Turn camera off and then on
again.
•
•
•
•
Use flash.
detection.
•
•
Use D (Best Shot Selector).
Use tripod and self-timer.
taken with flash.
Flash does not fire.
•
•
Flash is off.
are selected.
•
•
Movie mode is selected.
Continuous or Multi-shot 16 or BSS is
selected for Continuous in shooting menu.
Optical zoom cannot be used. Optical zoom cannot be used while recording
movies.
119
Troubleshooting
Problem
Cause/Solution
A
Digital zoom cannot be used.
Digital zoom cannot be used in the following
situations.
•
for Scene mode.
•
•
When using smart portrait mode.
applied while recording movies).
•
•
•
When Multi-shot 16 is selected for
Continuous.
Image mode not available.
shot 16 is selected for Continuous.
No sound when shutter is
released.
sound in setup menu. Even when set to On,
the shutter sound is not heard depending on
the current shooting mode or settings.
•
•
Do not block the speaker.
AF-assist illuminator does not
light.
setup menu.
•
some scene modes.
Pictures appear smeared.
Hues are unnatural.
Lens is dirty. Clean lens.
White balance does not match light source.
Randomly spaced bright pixels The subject is dark, so shutter speed is too slow
(“noise”) appear in image.
or ISO sensitivity is too high. Noise can be
reduced by:
•
Using flash.
Pictures are too dark
(underexposed).
•
•
•
•
•
Flash is off.
Flash window is blocked.
Subject is beyond flash range.
Adjust exposure compensation.
mode, or set the flash mode to X (fill flash).
Pictures are too bright
(overexposed).
Adjust exposure compensation.
120
Troubleshooting
Problem
Cause/Solution
A
Unexpected results when flash When taking pictures with V (auto with red-
set to V (auto with red-eye
eye reduction), or when taking pictures with
Night portrait (either in easy auto mode or the
Night portrait scene mode) and the fill flash with
slow sync and red-eye reduction is used, red-eye
reduction may be applied, in rare cases, to areas
not affected by red-eye. Use any auto mode or
scene mode other than Night portrait, and
change the flash to any other settings other than
V (auto with red-eye reduction) and try
shooting again.
reduction).
Playback
Problem
Cause/Solution
A
File cannot be played back.
File was overwritten or renamed by computer or
other make of camera.
–
Cannot zoom in on picture.
Playback zoom cannot be used with movies,
small pictures, or pictures that have been
cropped to 320 × 240 or smaller.
–
Cannot use D-Lighting, small
picture, or crop options.
•
•
These options cannot be used with movies.
Pictures taken at an Image mode setting of
P 3968×2232 cannot be edited.
•
•
picture, or crop.
Camera is unable to edit pictures taken with
other cameras.
•
•
Choose correct Video mode.
Pictures not displayed on
television.
Memory card contains no pictures. Replace
memory card. Remove memory card to play
back pictures from internal memory.
Nikon Transfer 2 does not start
when camera is connected.
•
•
•
•
•
Camera is off.
Battery exhausted.
–
USB cable is not correctly connected.
Camera is not recognized by the computer.
Computer is not set to launch Nikon Transfer 2
automatically. For more information about
Nikon Transfer 2, refer to help information
contained in ViewNX 2.
–
Pictures to be printed are not
displayed.
Memory card contains no pictures. Replace
memory card. Remove memory card to print
pictures from internal memory.
121
Troubleshooting
Problem
Cause/Solution
A
Cannot select paper size with
camera.
Even when using a PictBridge compatible
printer, paper size cannot be selected from the
camera in the following situations. Use the
printer to select paper size.
•
The printer does not support the paper sizes
used by the camera.
•
The printer automatically selects the paper
size.
122
Specifications
Nikon COOLPIX L24 Digital Camera
Type
Compact digital camera
Effective pixels
Image sensor
Lens
14.0 million
1/2.3-in. type CCD; approx. 14.48 million total pixels
3.6× optical zoom, NIKKOR lens
6.7-24.0mm (angle of view equivalent to that of 37-134 mm
lens in 35mm [135] format)
Focal length
f/-number
f/3.1-6.7
Construction
6 elements in 5 groups
Up to 4× (angle of view equivalent to that of approx. 536 mm
lens in 35mm [135] format)
Digital zoom
Vibration reduction
Autofocus (AF)
Electronic VR
Contrast-detect AF
•
Approx. 30 cm (1 ft.) to ∞ (W); approx. 70 cm (2 ft. 4 in.) to ∞
Focus range (from
lens)
(T)
•
Macro mode: 5 cm (2.0 in.) to ∞ (wide-angle position)
Focus-area selection
Monitor
Center, face detection
7.5 cm (3-in.), approx. 230k-dot, TFT LCD with 5-level
brightness adjustment
Frame coverage
(shooting mode)
Approx. 98% horizontal and 98% vertical (Compared to actual
picture)
Frame coverage
(playback mode)
Approx. 100% horizontal and 100% vertical (Compared to
actual picture)
Storage
Internal memory (approx. 17 MB), SD/SDHC/SDXC memory
card
Media
File system
File formats
DCF, Exif 2.2, and DPOF compliant
Still pictures: JPEG
Movies: AVI (Motion-JPEG compliant)
•
•
•
•
•
•
•
•
14M (High) [4320 × 3240P]
14M [4320 × 3240]
8M [3264 × 2448]
5M [2592 × 1944]
3M [2048 × 1536]
PC [1024 × 768]
Image size
(pixels)
VGA [640 × 480]
16:9 [3968 × 2232]
ISO sensitivity (Standard
output sensitivity)
Auto (ISO 80-1600)
123
Specifications
Exposure
Metering
256-segment matrix, center-weighted (when using less than
2× digital zoom), spot (digital zoom 2× or more)
Programmed auto exposure with motion detection and
exposure compensation (–2.0 to +2.0 EV in steps of 1/3 EV)
Exposure control
Shutter
Mechanical and charge-coupled electronic shutter
1/2000 - 1 s, 4 s (Fireworks show scene mode)
Electronically-controlled ND filter (-1.7 AV) selection
2 steps (f/3.1 and f/5.5 [W])
Speed
Aperture
Range
Self-timer
Built-in flash
Approx. 10 seconds
[W]: 0.5 to 7.0 m (1 ft. 8 in. to 22 ft.), [T]: 0.5 to 3.0 m (1 ft. 8 in. to
9 ft. 10 in.)
Range (approx.)
Flash control
Interface
TTL auto flash with monitor preflashes
Hi-Speed USB
Data transfer protocol MTP, PTP
Video output
I/O terminal
Can be selected from NTSC and PAL
Audio video output/digital I/O (USB)
Arabic, Chinese (Simplified and Traditional), Czech, Danish,
Dutch, English, Finnish, French, Greek, German, Hungarian,
Indonesian, Italian, Japanese, Korean, Polish, Portuguese,
Norwegian, Russian, Spanish, Swedish, Thai, Turkish
Supported languages
•
•
•
Two LR6/L40 (AA-size) alkaline batteries
Two FR6/L91 (AA-size) lithium batteries
Two EN-MH2 rechargeable Ni-MH batteries (available
separately)
Power sources
•
AC Adapter EH-65A (available separately)
Still pictures*:
•
•
•
Approx. 220 shots when using alkaline batteries
Approx. 700 shots when using lithium batteries
Approx. 450 shots when using EN-MH2 batteries
Battery life
Movies:
•
•
•
Approx. 2 h 5 min when using alkaline batteries (TV movie 640
)
)
Approx. 6 h 5 min when using lithium batteries (TV movie 640
Approx. 3 h 50 min when using EN-MH2 batteries (TV movie 640
)
Tripod socket
1/4 (ISO 1222)
Approx. 97.7 × 60.5 × 28.3 mm (3.9 × 2.4 × 1.2 in.) (excluding
projections)
Dimensions (W × H × D)
Approx. 182 g (6.5 oz.) (including batteries and SD memory
card)
Weight
124
Specifications
Operating environment
Operating
temperature
0 to 40°C (32 to 104°F)
Humidity
Less than 85% (no condensation)
• Unless otherwise stated, all figures are for a camera with fully-charged EN-MH2
batteries operated at an ambient temperature of 25°C (77°F).
*
Based on Camera and Imaging Products Association (CIPA) standards for measuring the life
of camera batteries. Measured at 23 ( 2) °C (69 to 77°F); zoom adjusted with each shot,
flash fired with every other shot, image mode set to R 4320 × 3240. Battery life may vary
depending on shooting interval and length of time menus and images are displayed.
Supplied batteries are for trial use only.
B Specifications
Nikon will not be held liable for any errors this manual may contain.
The appearance of this product and its specifications are subject to change without notice.
125
Specifications
Supported Standards
•
•
•
DCF: Design Rule for Camera File System is a standard widely used in the digital
camera industry to ensure compatibility among different makes of camera.
DPOF: Digital Print Order Format is an industry-wide standard that allows
pictures to be printed from print orders stored on the memory card.
Exif version 2.2: This camera supports Exif (Exchangeable Image File Format
for Digital Still Cameras) version 2.2, a standard that allows information stored
with photographs to be used for optimal color reproduction when images are
output from Exif-compliant printers.
•
PictBridge: A standard developed cooperatively by the digital camera and
printer industries, allowing photographs to be output directly to a printer
without connecting the camera to a computer.
126
Index
Battery level 18
Symbols
Battery-chamber 5
Battery-chamber/memory card slot cover
Best Shot Selector 76
Black-and-white 77
Blink warning 100
Brightness 90
BSS 76
Built-in microphone 4
Button sound 96
R 43
C
Calendar display 47
Cloudy 74
Color options 77
Compression ratio 72
Computer 57
Continuous 76
Copying pictures 106
Crop 52
Cyanotype 77
A
Alkaline 13
Alkaline batteries 12
Aperture 22
Audio-in/Video-in jack 56
Auto flash 28
D
Date imprint 92
Daylight 74
Digital zoom 21
Direct print 62
DPOF 126
AV Cable 56
AVI 110
DPOF printing 67
DSCN 110
B
127
Index
E
J
EH-65A 13
JPG 110
L
Language 99
Exposure compensation 32
Extension 110
Lithium batteries 12
Eyelet for camera strap 4
M
F
Macro mode 31
Memory capacity 18
Menus 85
File names 110
Fill flash 28
Firmware version 107
Monitor settings 90
Motion detection 94
Movie playback 55
Movie settings 54
Multi-shot 16 76
Flash off 28
Fluorescent 74
Folder names 110
Formatting internal memory 98
FSCN 110
N
Nickel-metal hydride batteries 12
H
Halfway 11
Help 11
O
I
Optical zoom 21
Identifier 110
Optional Accessories 108
Image review 90
Incandescent 74
Indicator lamp 5
Internal memory 16
ISO sensitivity 29
P
Photo info 90
128
Index
Playback menu 79
Playback zoom 48
Small size 54
Smart Portrait Mode 44
Sound settings 96
Speaker 4
SSCN 110
Preset manual 75
Standard color 77
Strap 11
T
Tabs 10
Print set 68
Thumbnail playback 46
Tripod socket 5
TV 56
Print Set (Date) 69
Printer 62
Protect 104
R
Recording movies 53
Reset all 101
Rotate image 105
RSCN 110
TV movie 54
U
USB cable 58
S
Self-timer 30
Sepia 77
V
Video Mode 99
Vivid color 77
Volume 55
Setup menu 83
Shooting Menu 70
Shooting-mode Selection menu 8
Shutter sound 96
Shutter speed 22
Single 76
W
Welcome screen 86
White balance 74
Z
Sleep Mode 97
Slide show 81
Slow Sync 28
Small picture 51
129
130
No reproduction in any form of this manual, in whole or in part
(except for brief quotation in critical articles or reviews), may be
made without written authorization from NIKON CORPORATION.
CT0K01(11)
6MM87911-01
|