Motorola Car Satellite Radio System DSR 6400 User Manual

Motorola DSR-6400 Series  
Satellite Multiplex Receiver/  
Transcoder Operator Guide  
DSR-6400  
MESSAGE  
Document No.: 583611-001  
Important Safety Instructions  
Unplug this apparatus during lightning storms  
or when unused for long periods of time.  
Read these instructions.  
Keep these instructions.  
Heed all warnings.  
Refer all servicing to qualified service  
personnel. Servicing is required when the  
apparatus has been damaged in any way, such  
as when the power-supply cord or plug is  
damaged, liquid has been spilled, or objects  
have fallen into the apparatus, the apparatus  
has been exposed to rain or moisture, does not  
operate normally, or has been dropped.  
Follow all instructions.  
Do not use this apparatus near water.  
Clean only with dry cloth.  
Do not block any ventilation openings. Install  
in accordance with the manufacturer’s  
instructions.  
Damage Requiring Service  
Unplug this equipment from the power source,  
and contact a qualified service provider if any of  
the following situations occurs:  
Do not install near any heat sources such as  
radiators, heat registers, stoves, or other  
apparatus (including amplifiers) that produce  
heat.  
If the power supply cord or plug is damaged.  
If liquid or objects have fallen into the unit.  
If the unit became wet from rain or water.  
If the unit was dropped or damaged.  
Do not defeat the safety purpose of the  
polarized or grounding-type plug. A polarized  
plug has two blades with one wider than the  
other. A grounding-type plug has two blades  
and a third grounding prong. The wide blade or  
the third prong is provided for your safety. If  
the provided plug does not fit into your outlet,  
consult an electrician for replacement of the  
obsolete outlet.  
If the unit’s performance changes.  
Service  
Do not try to service this product yourself. If you  
open or remove the cover, you may be exposed to  
dangerous voltage or other hazards and may void  
the unit’s warranty. Contact a qualified service  
provider for all service.  
Protect the power cord from being walked on  
or pinched, particularly at plugs, convenience  
receptacles, and the point where they exit from  
the apparatus.  
Use only attachments and accessories specified  
by the manufacturer.  
DSR-6400 Series  
3
ADVERTENCIA  
PRECAUCIONES DE OPERACIÓN  
ADVERTENCIA: PARA EVITAR RIESGOS DE INCENDIOS O  
DESCARGA ELÉCTRICA, NO EXPONGA ESTE EQUIPO A LA  
LLUVIA O LA HUMEDAD.  
La modificación no autorizada de cualquier unidad, y la venta y el uso  
del mismo está prohibida por ley. Cualquier modificación o alteración  
de este producto o cualquier recepción no autorizada de programación  
de televisión puede someter al usuario y al vendedor, y a la parte que  
modifica la unidad a multas, prisión y daños civiles.  
NOTA: Este equipo se ha probado y se ha demostrado que cumple con  
los límites para un dispositivo digital clase A, según la parte 15 de las  
normas de la FCC. Estos límites están diseñados para ofrecer protección  
adecuada contra interferencia dañina cuando el equipo se utiliza en un  
entorno comercial. Este equipo genera, usa y puede irradiar energía de  
radiofrecuencia y, si no se instala y usa de acuerdo con el manual de  
instrucciones, puede causar interferencia dañina a las comunicaciones  
por radio. Es posible que el funcionamiento de este equipo en un área  
residencial cause interferencia dañina, en cuyo caso el usuario deberá  
corregir la interferencia y asumir el costo correspondiente. Este aparato  
digital no supera los límites de la clase A de emisiones de ruido de radio  
del aparato digital establecido en las Normas de interferencia de radio  
del Departamento canadiense de comunicaciones.  
El símbolo del rayo con cabeza de flecha, dentro de un triángulo  
equilátero, está diseñado para alertar al usuario la presencia de  
"voltaje peligroso" sin aislamiento dentro del perímetro del  
producto que puede tener la magnitud suficiente para ser un  
riesgo de descarga eléctrica para las personas.  
El signo de exclamación dentro de un triángulo equilátero  
está diseñado para alertar al usuario la presencia de  
importantes instrucciones de funcionamiento y  
mantenimiento (servicio) en la literatura que acompaña al  
producto.  
PRECAUCIÓN  
RIESGO DE DESCARGA  
ELÉCTRICA. NO ABRIR.  
Reparación y asistencia  
PRECAUCIÓN: PARA REDUCIR EL RIESGO DE DESCARGA  
ELÉCTRICA, NO RETIRE LA CUBIERTA (O LA TAPA). EN EL  
INTERIOR NO H AY PIEZAS QUE SEAN PARA USO DEL USUARIO.  
SOLICITE ASISTENCIA TÉCNICA AL PERSONAL DE SERVICIO  
CALIFICADO.  
Para recibir ayuda sobre devolución o reparación, consulte “Product  
Nota para el instalador del sistema CATV  
ATENCIÓN  
Este recordatorio es para que el instalador del sistema CATV  
considere el Artículo 820-40 del Código eléctrico nacional (NEC) que  
entrega pautas para una correcta conexión a tierra y, en especial,  
especifica que la conexión a tierra del cable debe conectarse al sistema  
de conexión a tierra del edificio, lo más cerca posible del punto de  
entrada del cable.  
Esta unidad comercial está diseñada para decodificar señales  
de televisión DigiCipher II para uso comercial. La posesión de  
este dispositivo no permite ni autoriza al dueño a recibir señales  
de televisión DigiCipher II. Comuníquese con los proveedores  
de programa para obtener las autorizaciones correspondientes.  
®
MOTOROLA y el logotipo de la M estilizada son marcas  
comerciales o marcas comerciales registradas de Marcas  
Participantes de Motorola LLC. Todas las demás marcas  
comerciales son propiedad de sus respectivos dueños.  
Advertencia  
Dolby Digital es una marca comercial registrada de Dolby  
Laboratories. Dolby Digital está fabricado bajo la licencia de  
Dolby Laboratories.  
Para evitar descargas eléctricas, no use el enchufe eléctrico de la unidad  
(polarizado) con un cable de extensión, receptáculo u otra salida a  
menos que las aspas queden completamente insertadas para evitar la  
exposición de las aspas. El dispositivo de desconexión de la red de  
suministro es el enchufe del aparato y debe ser de fácil acceso y estar en  
funcionamiento.  
© 2012 Motorola Mobility, Inc. Todos los derechos reservados.  
La batería de litio no se reemplaza en la instalación para mantener la  
vida útil del producto.  
General Instrument Corporation comercializa como  
Motorola Mobility, Inc.  
6450 Sequence Dr.  
San Diego, CA 92121  
N°. DE DOCUMENTO: 583611-001 REV B, 2/2/12  
4
Instrucciones de seguridad importantes  
Proteja el cable de alimentación para evitar  
pisarlo o que quede apretado, especialmente en  
los enchufes y tomas de corriente, y revise el  
punto de salida del aparato.  
Lea estas instrucciones.  
Guarde estas instrucciones.  
Considere todas las instrucciones.  
Siga todas las instrucciones.  
No use este aparato cerca del agua.  
Limpie sólo con un paño seco.  
Use exclusivamente los accesorios  
especificados por el fabricante.  
Desconecte el aparato durante tormentas  
eléctricas o cuando no se use durante un  
tiempo prolongado.  
Daños que requieren servicio de  
mantenimiento  
No bloquee las aberturas de ventilación. Instale  
siguiendo las instrucciones del fabricante.  
Desenchufe este equipo de la fuente de  
alimentación y comuníquese con un proveedor de  
servicio calificado si se presenta alguna de las  
siguientes situaciones:  
No instale cerca de fuentes de calor como  
radiadores, rejillas de aire caliente, cocinas u  
otros aparatos que produzcan calor (incluidos  
amplificadores).  
Si el cable de alimentación o enchufe está  
dañado.  
No impida el propósito de seguridad del  
enchufe polarizado o con conexión a tierra. Un  
enchufe polarizado tiene dos aspas, una más  
ancha que la otra. Un enchufe de conexión a  
tierra tiene dos aspas y una tercera punta con  
conexión a tierra. El aspa ancha o la tercera  
punta está diseñada para su seguridad. Si el  
enchufe incluido no se ajusta a la salida, pida al  
electricista el repuesto de la salida obsoleta.  
Si sobre la unidad ha caído líquido o algún  
objeto.  
Si la unidad se moja por la lluvia o el agua.  
Si la unidad se golpeó o dañó.  
Si se altera el funcionamiento de la unidad.  
Servicio  
Todos los servicios de mantenimiento deben  
realizarlos personal calificado. El servicio de  
mantenimiento se requiere cuando el aparato  
tiene algún daño, por ejemplo cuando el cable  
de alimentación o enchufe está dañado, se ha  
derramado líquido o el aparato ha sido  
golpeado por otros objetos, cuando se ha  
expuesto a lluvia o humedad, no funciona  
normalmente o se ha caído.  
No intente reparar este producto usted mismo. Si  
abre o retira la cubierta, es posible que se exponga  
a voltaje peligroso u otros daños, y anule la  
garantía de la unidad. Para todo tipo de  
mantenimiento, comuníquese con un proveedor de  
servicio calificado.  
DSR-6400 Series  
5
Table of Contents  
Chapter 1 Introducing the DSR-6400 Series...................................................................................................... 13  
Chapter 2 Connecting the DSR-6400 Series Unit.............................................................................................. 17  
Chapter 3 Operating the DSR-6400 Series........................................................................................................ 23  
DSR-6400 Series  
7
1
8
DSR-6400 Series  
9
1
10  
Chapter 4 Product Support ................................................................................................................................ 79  
Chapter 5 Downlink/L-Band Frequency Conversion Tables .............................................................................. 81  
Chapter 6 Language Abbreviations ................................................................................................................... 83  
Chapter 7 Diagnostics........................................................................................................................................ 85  
Chapter 8 DSR-6400 Series Specifications ....................................................................................................... 99  
DSR-6400 Series  
11  
1
Introducing the DSR-6400 Series  
The Motorola DSR-6400 Series products are commercial Satellite Receiver/Transcoders, designed for  
broadcasters and headend operators for receiving digital satellite services. The DSR-6400 Series units  
will process both high-definition and standard-definition video services. After the DSR-6400 Series  
units are properly installed and configured, they will be ready to receive authorization and control  
information from the satellite signal source provider.  
Key Features  
• Eight RF inputs  
• DC-II QPSK and DVB-S2 demodulation  
• DigiCipher-II security  
• GigE and ASI inputs and outputs (Digital HD and SD output)  
• Two analog composite (SD) video output ports. The second (OSD video) is for diagnostic use.  
• VBI reinsertion for Closed Captioning  
• Two stereo pair audio output  
• DTMF output  
• Up to four Form-C relays for ad insertion support  
• One Form-C relay for fault alarm indication  
• Uplink controlled retunes  
• Memory: Configuration is saved in nonvolatile memory.  
• A two-line, 40-character front panel with a Liquid Crystal Display (LCD)  
DSR-6400 Series  
13  
   
1
• MPEG-2 HD and/or SD ASI and GigE outputs  
• Web Server GUI for remote operation  
• Advanced audio processing - Supports pass-through and decoding/decompression of Dolby  
AC-3 and pass-through of the Dolby E audio compression algorithm  
• Message Mailbox - Supports text message delivery from the uplink for display on the IRD’s  
front panel.  
• DPI support - Digital (SCTE-35) ad-splicing message support in both broadcast and unit-  
addressable formats  
• DTMF cue tone and Form-C contact closure relay terminals for each processed service  
Model and Transcoding Capacity  
The DSR-6400 Series includes a range of products differentiated by the number of services the units  
are able to simultaneously receive and transcode. The DSR-6401 transcodes one service, the DSR-  
6402 transcodes two, the DSR-6403 transcodes three, and the DSR-6404 transcodes four services.  
For setup purposes, the DSR-6400 Series introduces the concept of "processor" or PR in the user  
interface. A PR number in the user interface identifies the individual service processor path and the  
unique configuration settings assigned to (or the status information that pertains to) each program-  
mer service being received in a multi-service unit. Each path transcodes a single service according to  
its own unique configuration settings.  
The DSR-6400 Series provides service transcoding that processes up to four MPEG-4 HD input  
services into four MPEG-2 HD/SD output service pairs (up to eight total services). Figure 1-1 shows  
how service capacity varies by model.  
Input  
Service  
MPEG  
Program ID  
DSR-6400 Series Models  
Resolution Bit Rate  
SD  
HD  
SD  
HD  
SD  
HD  
SD  
HD  
CBR  
VBR or CBR  
CBR  
1
2
3
4
5
6
7
8
DSR-6401  
(one processor)  
1
2
3
4
Note: For example, on  
a DSR-6404, if all SD  
services are disabled in  
the transcoded output,  
then programs 1, 3, 5,  
and 7 will not be output.  
DSR-6402  
(two processors)  
VBR or CBR  
CBR  
DSR-6403  
(three processors)  
VBR or CBR  
CBR  
DSR-6404  
(four processors)  
VBR or CBR  
Figure 1-1: DSR-6400 Series Transcoding  
14  
   
PID Mapping  
The DSR-6400 Series uses a PID mapping scheme for the output services for ASI and GIGE output  
ports. The following two tables show each of the individual service components and their assigned PID  
values on each MPEG program. These PID values affect the output ports: ASI OUT 1, ASI OUT 2, and  
GIGE, as shown below. For multiple instances of the same component type, the unit increments the PID  
value by one.  
PID Assignments: ASI OUT 1 Port  
MPEG  
Program  
Processor  
Path  
Number  
Format  
PMT  
Video  
Audio1  
Audio2  
DPI  
DSMCC  
Subtitle  
Decimal  
Hex  
256  
100  
512  
200  
768  
300  
1024  
400  
272  
110  
288  
120  
544  
220  
800  
320  
1056  
420  
289  
121  
545  
221  
801  
321  
1057  
421  
304  
130  
560  
230  
816  
330  
1072  
430  
320  
140  
576  
240  
832  
340  
1088  
440  
336  
150  
592  
250  
848  
350  
1104  
450  
1
2
3
4
1
2
3
4
Decimal  
Hex  
528  
210  
784  
310  
1040  
410  
Decimal  
Hex  
Decimal  
Hex  
Note: The GIGE port  
carries the same PID  
mapping information as  
the two ASI OUT ports.  
ASI IN  
ASI OUT 1  
ASI OUT 2  
VIDEO OUT  
OSD VIDEO OUT  
10 / 100  
GIGE  
ETHERNET  
PID Assignments: ASI OUT 2 Port  
Program/ Transcoded  
Number  
Format  
PMT  
Video  
Audio1  
Audio2  
DPI  
DSMCC  
Subtitle  
Resolution  
From  
Decimal  
256  
100  
272  
110  
288  
120  
289  
121  
304  
130  
320  
140  
336  
150  
1 (SD)  
Hex  
ASI1  
Program 1  
Decimal  
Hex  
512  
528  
544  
545  
560  
576  
592  
2 (HD)  
3 (SD)  
4 (HD)  
5 (SD)  
6 (HD)  
7 (SD)  
8 (HD)  
200  
210  
220  
221  
230  
240  
250  
Decimal  
Hex  
768  
784  
800  
801  
816  
832  
848  
300  
310  
320  
321  
330  
340  
350  
ASI1  
Program 2  
Decimal  
Hex  
1024  
400  
1040  
410  
1056  
420  
1057  
421  
1072  
430  
1088  
440  
1104  
450  
Decimal  
Hex  
1280  
500  
1296  
510  
1312  
520  
1313  
521  
1328  
530  
1344  
540  
1360  
550  
ASI1  
Program 3  
Decimal  
Hex  
1536  
600  
1552  
610  
1568  
620  
1569  
621  
1584  
630  
1600  
640  
1616  
650  
Decimal  
Hex  
1792  
700  
1808  
710  
1824  
720  
1825  
721  
1840  
730  
1856  
740  
1872  
750  
ASI1  
Program 4  
Decimal  
Hex  
2048  
800  
2064  
810  
2080  
820  
2081  
821  
2096  
830  
2112  
840  
2128  
850  
DSR-6400 Series  
15  
   
1
Processor / Back Panel Associations  
Figure 1-2 shows how Processor numbers (PR) coincide with the Cue Tone ports and Relay ports on the back  
panel. For example, a DSR-6402 has two processors. The two services use cue tones Q1 (for Processor 1) and  
Q2 (for Processor 2). To execute Ad insertions, the two processors also use Relay port 1 (for Processor 1) and  
Relay port 2 port (for Processor 2). Figure 1-2 also shows how all PR fields are linked within the menu system.  
RELAY 1 ALARM  
PRIMARY AUDIO  
Q1+ Q1- G Q2+ Q2- L+ L-  
G
R+ R- NO CM NC G NO CM NC  
Available  
PR Fields  
Relay  
Ports  
Cue Tone  
Ports  
Model  
DSR-6401  
DSR-6402  
DSR-6403  
(none)  
1, 2  
1, 2, 3 (See Note.)  
1, 2  
Q1  
Q1, Q2  
1, 2, 3  
1, 2, 3  
Q1, Q2, Q3  
Q1, Q2, Q3, Q4  
L+ L-  
G
R+ R- NO CM NC G NO CM NC  
Q3+ Q3- G Q4+ Q4-  
SECONDARY AUDIO RELAY 2 RELAY 3  
DSR-6404 1, 2, 3, 4  
1, 2, 3, [4]  
If a fourth relay is necessary on a DSR-6404, see  
CHANNEL PR VCT  
CHNL Xpndr  
E
1
2
00000  
0000 (MPEG mode)  
Note: The DSR-6401 has one processor and  
does not display the PR field on any menu. It also  
uses three Relay ports (supporting up to three pos-  
sible ad insertion choices).  
MPEG SELECT  
PR  
Program  
2
E
00000(Not in map)  
The other models have one dedicated relay for  
each processor (supporting only one ad insertion  
choice per processor). For more ad insertion  
choices, use Cue Tones instead.  
STATUS7 SD PR Vido Frmt Resolutn BitRt  
MPEG-2 720x480 6.0M  
E
2
STATUS8 SD PR Aud Format Mode  
BitR  
---  
2
E
1
0
PSTHRU ---  
STATUS9 HD PR Vido Fmt Resolutn BitRt  
2
E
1 MPEG-2  
1280x720 18.0M  
STATUS10 HD PR Aud Format Mode BitR  
E
1
2
0
PSTHRU ---  
---  
DIAG  
Menus  
Fact 1  
Clear Cntrs PR  
No  
Changing any one of the PR fields will change  
all PR fields throughout the entire menu system.  
E
1
2
Figure 1-2: Processor / Back Panel Associations  
16  
     
2
Connecting the DSR-6400 Series Unit  
Unpacking and Connecting the DSR-6400 Series Unit  
Cable connections, described in this chapter, are made to the back panel of the unit.  
Earth Ground  
Terminals  
Relay/Alarm  
Primary Audio Out  
Fan Unit  
Fan Unit  
L-Band RF Input Ports 1 - 8  
RF IN  
PRIMARY AUDIO RELAY  
1
ALARM  
NO CM NC  
Q1+ Q1-  
G
Q2+ Q2- L+ L-  
G
R+ R- NO CM NC  
G
1
2
3
4
5
6
7
8
TVPass® Card  
ASI IN  
ASI OUT 1  
ASI OUT 2  
VIDEO OUT OSD VIDEO OUT  
RELAY  
CF  
TYPE  
1
CONTACT  
RATING 1A  
30 VDC  
L+ L-  
G
R+ R- NO CM NC  
G
NO CM NC  
Q3+ Q3-  
G
Q4+ Q4-  
10 / 100  
GIGE  
SECONDARY AUDIO RELAY  
2
RELAY  
3
ETHERNET  
CAUTION: DISCONNECT POWER CORD BEFORE SERVICING 100-240 VAC, 50 60 Hz  
/
ASI Out  
Video Out  
ASI In  
Power Connector  
Secondary Audio Out  
Ethernet Port  
GigE Port  
OSD Video Out  
TV Pass Card  
Figure 2-1: DSR-6400 Series Back Panel (Overview)  
DSR-6400 Series  
17  
     
2
Note: Additional audio and  
data connectors may be ordered  
through Phoenix Contact part  
numbers 1881354 / 1881370.  
PRIMARY AUDIO RELAY 1  
ALARM  
L+ L-  
G
R+ R-  
Q1+ Q1- G Q2+ Q2-  
Q3+ Q3- G Q4+ Q4-  
NO CM NC G NO CM NC  
CAUTION: When connecting  
any of the eight RF IN ports, the  
RF-IN Antenna cable should  
only be connected while the unit  
is properly grounded and the  
shield of the coaxial cable should  
be earthed in accordance with  
Article 820.93 of the NEC, ANSI/  
NFPA 70:2005 or equivalent.  
RELAY  
CONTACT  
RATING 1A  
30 VDC  
L+ L-  
G
R+ R- NO CM NC G NO CM NC  
SECONDARY AUDIO RELAY 2 RELAY 3  
CAUTION: DISCONNECT POWER CORD BEFORE SERVICING 100-240 VAC, 50 / 60 Hz  
RF IN  
1
2
3
4
5
6
7
8
ASI IN  
ASI OUT 1  
ASI OUT 2  
VIDEO OUT  
OSD VIDEO OUT  
10 / 100  
GIGE  
ETHERNET  
Figure 2-2: DSR-6400 Series Back Panel (Detailed)  
Unpacking  
The shipping carton contains the DSR-6400 Series unit, quick disconnect terminals, power  
cord, mounting brackets, mounting ears, rails, and this Operator Guide.  
18  
   
Rack Mounting Guidelines  
The DSR-6400 Series unit, with the supplied mounting brackets is designed for installation  
in an EIA standard 19-inch (480 mm) equipment rack. Place each unit in a stable and level  
position within the rack and ensure that all front enclosure screws are tightened to 14 in-  
lbs. If multiple DSR-6400 Series units are installed in a rack assembly, the operator may  
choose to have a certification agency evaluate the condition of the rack.  
Mechanical Loading  
The mounting rack location should be secure and level to avoid hazardous instability to the  
equipment due to uneven loading or weight distribution within the rack.  
Ambient Temperature  
When installing a DSR-6400 Series unit within a closed or multi-unit rack, the ambient  
temperature may be greater than the ambient temperature within the room. Therefore,  
verify that the amount of air flow required for safe operation is not compromised  
(maximum temperature for the equipment is 40° C). Consideration should be given to the  
maximum rated ambient temperature for the unit’s location when planning for cooling and  
air circulation. To evacuate the unit’s warm air output from within the mounting rack,  
Motorola Mobility recommends the use of a fan on top of the rack.  
Circuit Overloading  
If the unit is connected to a power strip, rather than a branch circuit’s direct connection, use  
special care to ensure that the unit is properly connected. Always consider the affect that  
overloading circuits might have on over-current protection and supply wiring. To ensure  
that circuits are not overloaded, read the DSR-6400 Series UL regulatory power label on  
top of the unit. Check all equipment power/amperage ratings to ensure the mounting rack  
power rating is not exceeded.  
Earth Ground  
Reliable earthing of rack-mounted equipment should be maintained. Particular attention  
should be given to supply connections other than direct connections to the branch circuit (e.g.  
use of power strips). The RF-IN antenna cable should only be connected while the unit is  
properly grounded. The shield of the coaxial cable should be earthed in YP accordance with  
Article 820.93 of the NEC (National Electrical Code), ANSI/NFPA 70:2005, or equivalent.  
Battery Replacement  
Do not replace the lithium battery used in the unit. Instead, return the unit to a Motorola  
Mobility authorized service center for replacement with the same or equivalent type  
battery as recommended by the manufacturer.  
DSR-6400 Series  
19  
           
2
Connecting the DSR-6400 Series  
To connect a DSR-6400 Series to the GigE signal, see "GigE Input" on page 31.  
To connect a DSR-6400 Series to an ASI signal, see "ASI Input" on page 31.  
To connect a DSR-6400 Series to an RF signal:  
1. Determine which satellite, transponder, Virtual Channel Table (VCT) number, and  
Virtual Channel is to be used. Contact the programmer for this system information so  
that the desired services can be received.  
2. Connect the desired L-Band (satellite antenna LNB or LNB signal splitter) source cable  
to RF Input Port 1 through 8, as directed by the programmer.  
Note: LNB power can be enabled for RF Input Port 1.  
3. To view video and On-Screen Diagnostics (OSD) during installation, connect the OSD  
Video Output on the back panel to a 75-ohm video monitor or television with  
composite video input (standard definition).  
Note: The unit generates time-specific ad insertion cue tones and relays. The  
programmer can include these messages in the encoded signal.  
4. If cue tones are needed and made available, connect the differential Cue Tone+, Cue Tone-,  
and Ground terminals on the unit to the 600-ohm device receiving the tones.  
Note: The unit provides an alarm relay that can be used to signal an alarm condition.  
To indicate an alarm, the unit provides a short-circuit electrical connection between the  
NC and CM terminals and an open-circuit electrical connection between the NO and  
CM terminals. With this configuration, the unit is able to signal an alarm, even for the  
loss of AC power.  
5. Plug the unit into a power source. Verify that the LCD screen is lit.  
6. Proceed with the installation using the front panel menus.  
7. For details on web server GUI, see "Remote Operation" on page 21.  
20  
 
Remote Operation  
The DSR-6400 Series decoder can be operated remotely from a web browser. When the  
decoder is contacted via an HTTP session from a computer, the decoder’s web server responds  
to the HTTP session with a login dialog box that requires the user to login with user name and  
password. Once the login is successful, the decoder’s web server then presents the unit’s home  
page to the browser.  
Some of the IRD configuration settings and control inputs that are accessible through  
HTTP include:  
• Virtual channel and audio language selection  
• Status and device information (e.g., signal strength, alarms, unit address)  
• Soft reset (AC power cycle)  
• Settings for acquiring a satellite signal (e.g., transponder frequency, input port)  
• Video and audio output customizations  
• Alarm triggers  
• ASI and Ethernet output customizations  
• Complete Transcoder configuration (Read-only when set by uplink programmer)  
To configure the DSR-6400 Series unit for remote operation  
1. Contact your network administrator for the IP Subnet Mask address, unique IP address,  
and default gateway address to assign to this decoder.  
Caution: By default, all DSR-6400 series units have the same IP address. To use  
the units remote operation, each unit on the subnet must be assigned a unique IP  
address. Failure to assign a unique IP address to each unit on the subnet will result in  
loss of connectivity.  
2. To configure the decoder, use the decoder’s arrow buttons on the front panel to perform  
the following procedures:  
3. Use an RJ-45 cable to connect the decoder’s Ethernet 10/100 port to the subnet that will  
be used to operate the decoder remotely.  
DSR-6400 Series  
21  
   
2
To operate the DSR-6400 Series decoder remotely  
1. Open a browser session, type the decoder’s unique IP address in the address bar, and  
press the ENTER key.  
For example, if the decoder is configured with IP address 10.11.23.60, then go to the  
browser, type: http://10.11.23.60 in the address bar, and press ENTER.  
2. When the login dialog box appears (as shown below), enter the User name and Password  
and select OK.  
Note: The uplink programmer who authorizes  
the unit has the option to set the User Name  
and Password. If they authorize the unit  
without using this option, leave both fields  
blank and simply select OK to gain access to  
web-based remote operation. (Blank) is the  
default User Name and Password.  
3. When the Home Page appears (as shown below), use the sidebar menu to access the  
decoder’s various settings and control features.  
.
22  
3
Operating the DSR-6400 Series  
All operations described in this chapter require use of the front panel, as shown in Figure 3-1.  
DSR-6400  
MESSAGE  
Relay  
Alarm  
LCD Screen  
Authorized Arrow Buttons  
Message  
ENTER Button  
Signal  
Download  
Figure 3-1: DSR-6400 Series Front Panel  
The following list describes the LEDs located on the left and right sides of the LCD screen.  
Relay  
Illuminates when relays are activated.  
Alarm  
Illuminates when the unit enters an alarm state.  
Authorized  
Message  
Signal  
Illuminates when the unit is authorized by the service provider.  
Illuminates when the unit has a mailbox message from the uplink.  
Illuminates when the unit is locked to a valid carrier.  
Download  
Blinks when a firmware download is in progress and illuminates solid when  
the unit has successfully received the firmware download and is waiting for  
activation by the programmer.  
DSR-6400 Series  
23  
   
3
Using the Front Panel  
The front panel LCD screen displays a series of menus that can be used to configure and control  
the system. The name of the current menu is always in the upper left corner of the screen for easy  
identification.  
Beneath every menu name are symbols representing key presses that are possible from the  
current cursor position in the menu. Note that the available keypad moves may change during  
the navigation between menu fields.  
Menu Name  
Label  
Label  
Label  
E
Setting Setting Setting  
The top row, to the right of the menu name, displays the name of each field available within  
that menu. These are called field labels and its setting is displayed directly below.  
Beneath each label is the current setting for each field.  
Some fields may be changed by the user and others are for display purposes only. Fields that  
can be changed have an arrow indicator ( ) just to the left of the field label. During left/right  
navigation, the cursor skips over the labels that cannot be changed.  
24  
 
Navigating the Menus  
Even though the keypad options shown on the LCD screen may change for each menu and for  
each field, the control buttons basically do the same thing. The user may want to practice on a  
screen to become familiar with how the buttons work. Notice that:  
Pressing the  
causes the cursor to scroll to another menu.  
buttons while the cursor is blinking next to the menu name (far left corner),  
  
Pressing ENTER while the cursor is blinking next to the menu name (far left corner) causes  
the cursor to scroll to the Main, top-level menu.  
Pressing the  
buttons while in the top line of the menu causes the cursor to move between  
4  
field labels (or the menu name and a field label).  
Pressing the button at the rightmost field label causes the cursor to wrap to the left side  
4
of the screen (to the menu name). Likewise, pressing the button when the cursor is at the  
menu name causes the cursor to wrap to the rightmost field label.  
When the cursor is blinking on a field label (top row), pressing ENTER causes the cursor to  
move below the label and enter into the field so the setting can be changed.  
When the cursor is below the label, the displayed directional controls in the left corner show what  
buttons can be pressed to change the setting in that field. When the symbol is left of the field, this  
indicates the ability to select from the available values. Placing the blinking cursor on those arrows  
and press the  
buttons to reveal each of the available choices for that field, one at a time.  
  
To store changes in a field and move back up to the label line, press ENTER.  
DSR-6400 Series  
25  
 
3
How to Use the Menus  
About Menu  
The front-panel LCD displays the About menu when the unit is initially plugged in or after a factory  
reset. This menu identifies the model (either DSR-6401, DSR-6402, DSR-6403, or DSR-6404) and  
the second line displays the DSR-6400 Series’s actual firmware version instead of 0xXXXXX, as  
shown below.  
MOTOROLA DSR-6400  
Version 0xXXXXX  
This menu is displayed for 10 seconds, then the front-panel LCD displays the Main menu.  
Main Menu  
This menu is the top-level menu and can be accessed from any other menu by pressing ENTER  
while the cursor is blinking next to the menu name. This menu allows the user to select any one of  
the five main menu groups: Installation menus, Channel menus, IP menus, Status menus, and  
Diagnostic menus.  
DSR-640X  
E Install Channel IP Status Diag  
Note: In the above graphic, the X in DSR-640X designates the exact model (DSR-6401,  
DSR-6402, DSR-6403, or DSR-6404).  
The unit allows the user to scroll ( ) only to menus that are in the same group. To scroll to a  
  
menu that is in a different menu group, return to the main top-level menu and select the desired  
menu group. To return to the main top-level menu from any menu, place the cursor in the upper-left  
corner and press ENTER.  
26  
     
Overview of The LCD Panel Menu Tree  
Pressing ENTER when the cursor is on a menu name causes the cursor to return to the main, top level  
menu. The charts on the following pages show the menus organized into five main groups: Installation  
menus, Channel selection menus, IP menus, Status menus, and Diagnostic menus.  
INSTALLATION MENUS  
MANUAL TUNE Input Mode Xpndr LFreq  
Port 1 Xpndr 01 1430.00  
AUDIO1 GAIN  
Mode  
Left  
Right  
+00  
E
E
Joint  
+00  
MANUAL TUNE Input  
ASI In  
AUDIO2 GAIN  
Mode  
Left  
Right  
+00  
E
E
Joint  
+00  
ALARM  
Trigger  
Auto  
Test  
Off  
MANUAL TUNE Input  
GigE In  
E
E
Note: The Modulation,  
Port, and Port Config  
menus are only present  
when one of the RF  
ports is selected as the  
input within the Manual  
Tune menu.  
4th RELAY  
Config  
Alarm  
GigE Input IP Address  
239.001.001.001  
Port  
00000  
E
E
MODULATION Mode  
DCII-AUTO  
ASI OUTPUT Enable  
On  
E
E
The 4th Relay menu is  
only present on a  
DSR-6404.  
MODULATION Mode  
DVBS2  
Symbol  
ASI OUTPUT RATE  
ASI1  
ASI2  
E
30.000000  
E
78  
108  
The GigE Input menu is  
only present when GigE  
is selected as the input.  
MODULATION Mode  
Symbol  
RESET Reset Type  
Code Select  
E
8PSK-TC  
01.000000  
E
No  
0x333 active  
MODULATION Mode  
Symbol  
CORE  
Contrast  
E
18  
E
DVB-MAN  
01.000000  
VIDEO OUT 525 625  
NTSC PAL-625  
MODULATION Mode  
Sym Code Format  
E
E
DCII-MAN 19.51 3/4 Comb  
FIRMWARE Boot:FPGA:High  
Upgrade  
PORT ID Mode Sat  
Auto ---  
Polar  
---  
E
1
E
XXXXXX:XXXXXX:XXXXXX 000000  
DOWNLOAD File  
Current Rcvd Total  
PORT CONFIG  
Port 1 Power  
E
00 of 00 0000 0000 0000  
E
Off  
DR MODE  
VCT  
VCN  
PORT  
AUDIO1 AudioMix  
Stereo  
DialNorm/Compress  
E DISABLED  
(00000) ---- NA  
E
On-Moderate  
AUDIO2 AudioMix  
Stereo  
DialNorm/Compress  
E
On-Moderate  
DSR-6400 Series  
27  
 
3
Channel Selection Menus  
CHANNEL PR VCT  
CHNL Xpndr  
E
1
00000  
0000 (MPEG mode)  
MPEG SELECT  
PR  
Program  
E
1
00000(Not in map)  
AUD1LANG Dspl Left  
All def  
Right InputMode  
E
def  
---  
AUD2LANG Dspl Left  
Right InputMode  
def ---  
E
All def  
IP MENUS  
PORT GigE  
IP Address  
PORT 10/100  
MAC Address  
hh:hh:hh:hh:hh:hh  
E
192.168.054.100  
E
PORT GigE  
Subnet Mask  
PORT 10/100  
DHCP  
Unit Name  
E
255.255.255.000  
E
Disable DSR640X-XXXXX  
PORT GigE  
Default Gateway  
PORT 10/100  
IP Address  
E
192.168.054.002  
E
192.168.000.100  
PORT GigE TS Mode  
Off  
DSMCC  
PORT 10/100  
Subnet Mask  
E
Off  
E
255.255.255.000  
PORT GigE Xcoded Dest Addr  
192.168.054.201  
Port  
PORT 10/100  
Default Gateway  
E
06100  
E
192.168.000.001  
PORT GigE PassThru Dest Addr  
192.168.054.200  
Port  
PORT GigE  
MAC Address  
E
06000  
E
hh:hh:hh:hh:hh:hh  
28  
Status Menus  
STATUS7 SD PR Vido Frmt Resolutn BitRt  
MPEG-2 720x480 6.0M  
STATUS0 Health  
Alarm Trigger  
Auto  
E
1
E
Acq:Alarm  
STATUS1 FrontPanel  
Input Type  
L-Band  
STATUS8 SD PR Aud Format Mode  
PSTHRU ---  
BitR  
---  
E
Local-Control  
E
1
0
STATUS2 Source  
Channel  
----  
Quality  
---  
STATUS9 HD PR Vido Fmt Resolutn BitRt  
MPEG-2 1280x720 18.0M  
E
---  
E
1
STATUS3 Signal Quality  
|||||||||||||||||||||||.......  
STATUS10 HD PR Aud Format Mode BitR  
PSTHRU --- ---  
E
E
1
0
STATUS4 Sat Freq  
Symb Code Format  
STATUS11 Addr Field  
----------  
Link Field  
Off  
E
--- 1430.00 11.71 5/6 Comb  
E
STATUS5 Sync Eb/No Authorize State  
Tuning -2.0 Undefined Service  
STATUS12 MAIL: INBOX  
> 0/0  
E
E
STATUS6 Memory  
8.0MB  
Flash  
Hard Drive  
STATUS13 MAIL: ARCHIVE > 0/0  
E
450.4MB 14.9GB  
E
Diagnostic Menus  
DIAG Menus  
PR  
E
Off  
1
UNIT ADDRESS  
E
ddd-ddddd-ddddd-ddd  
TV PASS CARD Status  
E
Not Inserted  
AUDIO TEST SIGNAL L1/R1  
L2/R2  
E
Off  
Off  
VIDEO TEST SIGNAL Pattern  
Off  
E
AD INSERTION TEST Cue Tone Relay  
E
Off  
Off  
DSR-6400 Series  
29  
3
Installation Menus  
The purpose of the installation menus is to configure the ports and choose settings that remain  
fixed over time. This section describes in detail each of the Installation menus, fields, and options  
displayed on the LCD panel.  
Return to the main top-level menu and then select the Installation menu group.  
With the blinking cursor at the upper left, press the ENTER button to return to the main top-level  
menu. Press the  
buttons until the cursor is at the Install label, and press ENTER. The unit  
4  
displays the previously-selected sub-menu.  
Manual Tune Menu  
Use this menu to begin to acquire a DigiCipher II system signal, by selecting a transponder  
frequency for one of the eight L-Band inputs. In addition, this menu allows a user to select the  
ASI input or GigE input, as an alternative to RF ports 1 through 8.  
MANUAL TUNE Input Mode Xpndr LFreq  
Port 1 Xpndr 01 1430.00  
To specify an RF input port, see  
E
To specify the ASI In as the input port,  
MANUAL TUNE Input  
ASI In  
E
To specify the GigE In as the input port,  
MANUAL TUNE Input  
GigE In  
E
30  
   
ASI Input  
Input Field  
Use this section to specify the ASI input port. The Input field displays the active input. Press the  
4
button until the cursor is at the Input label and press ENTER. Press the  
buttons to scroll to ASI  
  
In. Press ENTER to confirm the selection and return to the top line of the menu.  
MANUAL TUNE Input  
E
ASI In  
The following screen prompts the user to confirm the selection and exit the field.  
Service will be interrupted  
Press E to continue or  
to stop  
If you press any arrow button (  
) at this point, the Caution screen disappears and the  
4  
MANUAL TUNE menu reappears without any changes. To set the port selection, press ENTER.  
GigE Input  
Input Field  
Use this section to specify the GigE input port. The Input field displays the active input. Press the  
4
button until the cursor is at the Input label and press ENTER. Press the  
buttons to scroll to GigE  
  
In. Press ENTER to confirm the selection and return to the top line of the menu.  
MANUAL TUNE Input  
E
GigE In  
The following screen prompts the user to confirm the selection and exit the field.  
Service will be interrupted  
Press E to continue or  
to stop  
If you press any arrow button (  
) at this point, the Caution screen disappears and the  
4  
MANUAL TUNE menu reappears without any changes. To set the port selection, press ENTER.  
DSR-6400 Series  
31  
           
3
GigE Input IP Addr Field  
Default: 239.001.001.001  
Use the following procedure to set and view the Input GigE IP address of the unit. Press the  
  
buttons until the GigE Input IP Address menu appears. Use this menu to enter an IP address and  
Port for the incoming GigE source stream. The address is represented in the common dotted-  
decimal format. Contact the network administrator for details about configuring the GigE input  
port for the desired source stream.  
GigE Input IP Address  
239.001.001.001  
Port  
E
00000  
Important: Do not configure the IP Address of the 10/100 and GigE to be on the same subnet.  
Press the button until the cursor is at the IP Address label, and press ENTER to move into the  
4
field. Use the arrow buttons (  
) to enter the desired address and then press ENTER to  
4  
confirm the selection and exit the field. Skip to page 38 to set the remaining installation fields.  
RF Input  
Use this section to select one of the eight RF input ports so that the unit can acquire the DigiCipher  
II system signal and automatically download network data required for operation.  
Because many satellite broadcasters use standard C-band transponder center frequencies,  
selecting a transponder number is the default tuning mode. Use the Xpndr option in the Mode  
field and edit the Xpndr (transponder) field (described on page 33), for tuning such signals.  
For offset-frequency C-band, fractional transponders, or Ku-band satellite broadcasts, use the  
LFreq field in the Mode field (described on page 34), and directly edit the L-band frequency field.  
The unit does not actually require any distinction between C-band and Ku-band satellite signals in  
order to tune and acquire a compatible signal. However, correct modulation information is  
necessary. For details on modulation, see “Modulation Menu” on page 35.  
Input Field  
Default: Port 1  
The Input field displays the active input. To select the input:  
Press the button until the cursor is at the Input label and press ENTER. Press the  
buttons to  
  
4
scroll to the input that is connected. Unless changed, the unit displays Port 1. Press ENTER to confirm  
the selection and return to the top line of the menu. If Port 1 through Port 8 is selected, then use the  
arrow buttons ( ) to specify the other fields (Mode field, Xpndr field, and Lfreq field) as  
4  
needed. These three fields are not visible when ASI In or GigE In is selected.  
MANUAL TUNE Input Mode Xpndr LFreq  
E
Port 1 Xpndr 01  
1430.00  
32  
     
The following screen prompts the user to confirm the selection and exit the field.  
CAUTION: Service will be interrupted  
Press E to continue or  
to stop  
If you press any arrow button (  
) at this point, the Caution screen disappears and the  
4  
MANUAL TUNE menu reappears without any changes. To set the port selection, press ENTER.  
Mode Field  
Default: Xpndr  
The Mode field allows selection of the frequency plan type for the satellite signal to which the  
unit is tuned. If the application is a North American C-band satellite center frequency, select the  
transponder number in the Xpndr field. Otherwise, set this field to LFreq and also set the new  
field (LFreq) as described on page 34. The L Freq option can be used for all satellite LNB signals,  
including C-band and Ku-band.  
Press the button until the cursor is on the Mode label. Then press ENTER to move into the field.  
4
There are two choices: Xpndr and L Freq. Press the  
buttons to display the desired choice.  
  
Then press ENTER to confirm the selection and exit the field.  
If Xpndr is selected, choose a transponder in the Xpndr field. The frequency in the LFreq field is  
set automatically and cannot be edited.  
If L Freq is selected, the Xpndr field no longer appears because the transponder/ frequency  
relationship is not known. Select a transponder frequency between 950 and 2150 MHz in the  
LFreq field. This field is not available when Input field is set to either ASI In or GigE In.  
Xpndr Field  
This field is not available when Input field is set to either ASI In or GigE In. This field is not  
available when the Mode field is set to LFreq.  
This field allows selection of an initial satellite transponder number and can only be used if the  
Xpndr option in the Mode field is selected. Press the  
label. Then press ENTER to move into the field.  
button until the cursor is at the Xpndr  
4
Then press the  
buttons to select the desired transponder number. Since the associated  
  
transponder/frequency tables are stored in the unit, scroll through the transponder numbers and  
notice that the associated frequency (shown in the LFreq field to the right) automatically changed  
with the selection (970-1430 MHz). There are 24 transponder options, and when the desired  
transponder selection is displayed, press ENTER to confirm selection and move the cursor back  
up to the field label.  
DSR-6400 Series  
33  
   
3
LFreq Field  
This field is not available when Input field is set to either ASI In or GigE In. If the Mode field is  
set to Xpndr, this field is set automatically and cannot be edited.  
If the LFreq option in the Mode field is chosen, use this field, to directly tune the frequency. Press  
the button until the cursor is at the LFreq label. Then press ENTER to move into the field.  
4
Use the arrow buttons (  
4   
) to select the desired frequency. Select a frequency between  
950 MHz and 2150 MHz and press ENTER to confirm the selection and move the cursor back to  
the field label.  
For those satellite carriers which are offset (C-band or Ku-Band), use the L Freq option to enter  
the exact center frequency of a carrier, rather than using a nearby- but-not-exact C-band  
transponder center frequency. Long-term frequency tracking is best if the user enters a precise  
carrier center frequency.  
Contact the programmer or network operator for details about the satellite, transponder, and fre-  
quencies being used.  
34  
 
Modulation Menu  
This menu is not available when the Manual Tune menu has the Input field set to ASI In or GigE  
This menu, together with the Manual Tune menu, allows the user to initially acquire a DigiCipher II  
signal. Press the  
buttons until the MODULATION menu appears. Press ENTER to continue.  
  
MODULATION Mode  
DCII-AUTO  
E
When the DCII-MAN option is selected, the user must also specify a Symbol/Code/Format  
combination. When the Mode field is set to DVBS2, the user must also specify a Symbol Rate (Msps).  
MODULATION Mode  
DVBS2  
Symbol  
E
30.000000  
MODULATION Mode  
Symbol  
E
8PSK-TC  
01.000000  
MODULATION Mode  
Symbol  
E
DVB-MAN  
01.000000  
MODULATION Mode  
Sym Code Format  
E
DCII-MAN 19.51 3/4 Comb  
Mode Field  
Default: DCII-AUTO  
Press the button until the cursor is at the Mode label, and press ENTER to move into the field.  
4
Press the  
buttons to display the options: DCII-AUTO, DCII-MAN, or DVBS2. Select a  
  
mode and press ENTER to exit the field.  
Note: In order to receive a DVB-S2 modulated carrier, the unit must be set to DVBS2 mode and  
the correct Symbol Rate (Msps) must be entered in the Symbol field. In DCII-MAN mode, the  
correct Symbol Rate (Msps) must be entered in the Sym field, Code field, and Format field. If  
DCII-AUTO is selected, the unit searches through all available DC-II Symbol/Code/Format  
combinations to acquire a signal and then remains locked on that signal.  
Symbol / Code / Format Fields  
Default: 19.51 3/4 Comb  
These three field are not available when the Mode field is set to DCII-AUTO. If the Mode field is set to  
DCII-MAN, press the button until the cursor is at the Sym label and press ENTER to move into the  
4
field. Use the  
buttons to scroll through the combinations. Each time a  
button is pressed, the  
  
  
unit provides a three-field combination for the Sym field, Code field, and Format field. Select the  
combination provided by your programmer and press ENTER to confirm and exit the field.  
If the Mode field is set to DVBS2, the Symbol field can be edited to any value up to 33.000000 by  
using the arrow buttons ( ) to edit each digit.  
4  
DSR-6400 Series  
35  
     
3
Port Menu  
Use this menu to configure RF In ports (Port 1 through Port 8). This menu is not available when the  
Manual Tune menu has the Input field set to ASI In or GigE In. That option is described on page 32.  
Because the unit has eight RF input ports that can potentially be used to switch and tune signals  
from multiple satellite antenna, the unit demands there be an accurate association of the port with  
the Satellite and Polarity designators programmed in the Uplink encoder system(s) to which we  
plan to downlink from on each port.  
Because accuracy is critical, a default Auto mode automatically updates the Sat (Satellite) and Polar  
(Polarity) fields for the one port that is currently being tuned. This automatic population of the fields  
occurs upon entry of acceptable channel information.  
To ensure success in getting initial authorization, decryption, and output, leave this menu  
unchanged in Auto mode (as shown below).  
PORT ID Mode  
Auto  
Sat  
---  
Polar  
---  
E
1
If the Uplink Signal Provider gives detailed instructions, set the Mode field to Manual and set the  
Sat (Satellite) field and Polar (Polarity) field. Any mismatch between what is entered into these  
fields and the Uplink encoder Satellite and Polarity designations for the services will prevent  
authorization decryption and service output. Satellite names and polarity designators for a given  
service do not necessarily reflect actual satellite names or even the correct polarity of the actual  
signal. These values are set within the provider’s encoder system.  
ID Field  
Default: 1  
Use this field to choose which port to configure (1 through 8). Press the button until the cursor  
4
is at the ID field, press ENTER to move into the field. Use the  
press ENTER to confirm the selection and exit the field.  
buttons to choose a port and  
  
Mode Field  
Default: Auto  
Use the Mode field to select the mode for port setup. Press the button until the cursor is at the Mode  
4
label, and press ENTER to move into the field. Press the  
buttons to choose the desired mode  
  
(either AUTO and MANUAL) and press ENTER to confirm the selection and exit the field.  
36  
     
Sat Field  
Default: ---  
If the Mode field is set to Manual, use this field to select a satellite name for the designated port.  
This field is not editable when the Mode field is set to Auto. Press the button until the cursor is  
4
at the Sat label. Press ENTER to move into the field.  
If the unit has locked to a signal (check the front-panel SIGNAL LED), the unit will download the  
satellite name(s) used by the provider. Leaving the blinking cursor on the up/down symbol ( )  
left of the field, use the  
  
select one and exit the field.  
buttons to reveal the downloaded satellite name(s). Press ENTER to  
If the unit is not locked to a signal and the provider has instructed specific port programming, use the  
buttons to select the character position to be changed. Then use the buttons to scroll  
4  
  
through the character choices and press ENTER to confirm selection and exit the field.  
This field displays dashes (---) when the port is not related to a satellite.  
Polar Field  
Default: ---  
If the Mode field is set to Manual, use this field to select a polarity for the designated port. Press the  
4
button until the cursor is at the Polar label. Press ENTER to move into the field and press the  
  
buttons to display the options: H/LHP (Horizontal/Left-Hand Polarity) or V/RHP (Vertical/Right-  
Hand Polarity). Select a polarity and press ENTER button to confirm the selection and exit the field.  
Port Config Menu  
Use this menu to configure Low Noise Block (LNB) power for RF In Port 1. This menus is not  
available when the Input field is set to either ASI In or GigE In.  
PORT CONFIG  
Port 1 Power  
E
Off  
Port 1 Power Field  
Default: OFF  
Use this field to direct power to the external Low Noise Block (LNB). Press the button until the  
4
cursor is at the Port 1 Power label, and press ENTER to move into the field. Press the  
buttons to  
  
display the options: OFF and ON. When the ON option is selected, the unit supplies 16-22 VDC on the  
RF In Port 1 antenna input connector, as shown in Figure 2-2 on page 18.  
DSR-6400 Series  
37  
       
3
Audio1 and Audio2 Menus  
Use these menus to customize the back-panel analog audio outputs (Phoenix connectors). Press  
the  
buttons until the Audio1 or Audio2 menu appears (shown below).  
  
AUDIO1 AudioMix  
Stereo  
DialNorm/Compress  
E
On-Moderate  
AUDIO2 AudioMix  
Stereo  
DialNorm/Compress  
E
On-Moderate  
AudioMix Field  
Default: Stereo  
Important: If the audio input mode is stereo and you are connecting to a mono modulator, you  
must set this field to Mono.  
This field allows selection of the audio processing options. Press the button until the cursor is  
4
at the AudioMix label, and press ENTER to move into the field. Press the  
the options:  
buttons to display  
  
Stereo  
Stereo output on both left and right channels  
Dual Mono Mono output on both left and right channels that can each be assigned to a  
unique language  
Mono  
Duplicate mono output on both left and right channels  
Enhanced stereo with surround pass-through  
Surround  
Caution: If Dual Mono is selected, a caution screen appears. If Dual Mono is selected and then  
changed to another option, the caution screen appears again. This caution message denotes possible  
conflicts between this menu and the language selection menus that could mute the audio. By  
pressing ENTER (ignoring the caution), the unit changes to Dual Mono, and uses the language  
previously selected for Mono (or Stereo) for both left and right channels.  
CAUTION: Check audio language selection  
Press E to continue or  
to stop  
If it is necessary to select a single language for Mono, Dual Mono, or Stereo output, see  
38  
   
DialNorm/Compress Field  
Default: On-Moderate  
DialNorm is an abbreviation for Dialog Normalization. This field enables or disables dialog  
normalization and allows control of the degree of audio level compression. Press the button  
4
until the cursor is at the DialNorm/Compress label, and press ENTER to move into the field.  
Press the  
buttons to display the options:  
  
On-Moderate  
Enables dialog normalization. The degree of compression is moderate,  
which provides some reduction and amplification of the audio signal, but  
the thresholds are wider apart, providing moderate dynamic range of the  
audio signal.  
On-Off  
Enables dialog normalization. Compression is not used and provides full  
dynamic range of the audio signal.  
Off-Off  
Disables dialog normalization. Compression is not used and provides full  
dynamic range of the audio signal.  
On-Heavy  
Enables dialog normalization. The degree of compression is heavy, which  
reduces the louder audio signals and boosts the softer signals using tighter  
compression thresholds, in order to eliminate dramatic fluctuations in the  
audio signal level and suppress dynamic range of the audio signal.  
Press ENTER to confirm the selection and exit the field.  
Note: When dialog normalization is enabled, the audio levels for speech are normalized to a  
constant level for all channels. The volume of the dialogue is thus raised or lowered to a level that  
is appropriate for the background sound track.  
DSR-6400 Series  
39  
 
3
Audio1 and Audio2 Gain Menus  
These menus allow adjustment of the audio signal output level from +00 to -20 dB, in 1 dB  
increments. Press the  
AUDIO2 GAIN).  
buttons until the desired menu appears (either AUDIO1 GAIN or  
  
AUDIO1 GAIN  
Mode  
Left  
Right  
+00  
E
Joint  
+00  
AUDIO2 GAIN  
Mode  
Left  
Right  
+00  
E
Joint  
+00  
The user may adjust the output levels of the left and right channels jointly. The output level of the  
right channel tracks the setting for the left channel when the output levels are adjusted jointly.  
Mode Field  
Default: Joint  
Note: The Mode field is not editable.  
This field is associated with the Audio Gain port and is always set to Joint. This means, both  
channels are configured jointly using the Left field settings as the control for both audio channels.  
Left and Right Fields  
Default: +00  
Note: The Right field is not editable.  
The Left field allows adjustment of the output level of the Left and Right audio signals. Press the  
button until the cursor is at the Left label, and press ENTER to move into the field. Use the  
4
  
buttons to simultaneously adjust the output level for the Left and Right audio signals from  
+00 to -20 dB, in 1 dB increments.  
Press ENTER to confirm the selections.  
40  
     
Alarm Menu  
Use this menu to choose which alarm condition will activate an alarm. Press the button until  
the Alarm menu is located (shown below).  
ALARM  
Trigger  
Test  
E
Auto  
Off  
The alarm can be activated for any of the following conditions:  
The unit’s tuner loses lock when the input is RF.  
The unit cannot lock to the ASI input when the input is ASI.  
The unit is unable to render video.  
The unit is not authorized to access the selected service.  
The unit loses power.  
The unit’s GigE Port Link state is inactive when the Input field (described on page 32) is  
set to GigE In.  
Trigger Field  
Default: Auto  
The Trigger field allows the user to select the trigger condition to activate an alarm on the IRD.  
When the alarm is activated, the Alarm LED illuminates and the alarm relay indicates an alarm  
condition.  
Press the button until the cursor is at the Trigger label, and press ENTER to move into the field.  
4
  
Press the  
buttons to display the five options:  
Disabled  
Auto  
Disables the IRD alarm feature.  
Enables all triggers for an IRD alarm.  
Auto+HDD  
No Signal  
No Video  
No Auth (Authorization)  
Alarm is triggered when the IRD detects a hard drive fault.  
Alarm is triggered when the IRD loses the incoming signal.  
Alarm is triggered when the IRD loses analog video output.  
Alarm is triggered when the IRD is not authorized to access a  
selected service.  
Press ENTER to select the desired option and exit the field.  
Test Field  
Default: Off  
Note: The Test field returns to the default value (Off) when the field is exited.  
The Test field provides an IRD alarm test when this field is set to On. Press the  
display the two options: Off or On.  
buttons to  
  
Press ENTER to select the option shown and exit the field.  
DSR-6400 Series  
41  
     
3
4th Relay Menu (DSR-6404 only)  
Use this menu to repurpose the Alarm Relay (on the back panel) for use as the fourth contact  
closure output. To pins are labeled NO, CM, and NC and are located below the ALARM label, as  
4th RELAY  
Config  
E
Alarm  
Config Field  
Default: Alarm  
Use the Config field to choose the purpose of the fourth relay. Press the button until the cursor  
4
is at the Config label, and press ENTER to move into the field. Press the  
the two options:  
buttons to display  
  
Alarm  
Enables alarm functionality for the fourth relay and disables ad  
insertion functionality.  
Ad Insertion  
Enables ad insertion functionality for the fourth relay and disables  
alarm functionality.  
ASI Output Menu  
Press the  
buttons until the ASI Output menu appears. Use this menu to configure the digital  
  
ASI OUT 1 on the back panel.  
ASI OUTPUT Enable  
On  
E
Enable Field  
Default: On  
Note: The ASI OUT 1 on the back panel can be disabled by control information from the Uplink  
Programmer (Broadcast Network Controller [BNC]).  
Use this field to enable or disable the ASI OUT 1 on the back panel. The ASI OUT 2 on the back  
panel is not affected by this setting and always remains enabled. When ASI output is disabled by  
the BNC, this field is not editable and displays Lock Off. Otherwise, if the BNC enables the ASI  
output, this field is editable with the default value (On). Press the  
options (On and Off).  
buttons to display the  
  
Note: For PID values associated with ASI output ports, see "PID Mapping" on page 15.  
42  
         
ASI Output Rate Menu  
Press the  
buttons until the ASI Output Rate menu appears. Use this menu to designate the  
  
unit’s ASI output rate.  
ASI OUTPUT RATE  
ASI1  
ASI2  
E
78  
108  
Note: The unit has two ASI output ports on the back panel:  
ASI OUT 1: The unit passes-through only the input MPEG programs that the unit is processing  
(refer to the Channel Menus). In either case, the processed programs are decrypted.  
ASI OUT 2: The unit also converts selected input MPEG-4 programs to both an MPEG-2 HD  
(High Definition) program and an MPEG-2 SD (Standard Definition) program. These input  
programs are selected using the Channel menus.  
ASI1 Field  
Default: 78  
To select the data rate (Mbps) of the ASI OUT 1 on the back panel, press the button until the  
4
  
cursor is at the ASI1 label, and press ENTER to move into the field. Press the  
display the options: 19.5, 39, and 78.  
buttons to  
Note: The unit formats the ASI OUT 1 on the back panel in either the byte mode or the packet  
mode. The unit automatically selects one of the two format modes for the best compatibility with  
the devices receiving the ASI output.  
Byte Mode  
The unit formats the ASI output in the byte mode when the selected ASI  
output data rate is 54 Mbps or less.  
Packet Mode  
The unit formats the ASI output in the packet mode when the selected ASI  
output data rate is greater than 54 Mbps.  
ASI2 Field  
Default: 27 (DSR-6401); 54 (DSR-6402); 81 (DSR-6403); 108 (DSR-6404)  
To select the data rate (Mbps) of the ASI OUT 2 on the back panel, press the button until the  
4
  
cursor is at the ASI2 label, and press ENTER to move into the field. Press the  
display the options: 27, 54, 81, and 108.  
buttons to  
Note: The unit formats the ASI OUT 2 on the back panel in either the byte mode or the packet  
mode. The unit automatically selects one of the two format modes for the best compatibility with  
the device that is receiving the ASI output.  
Byte Mode  
The unit formats the ASI output in the byte mode when the selected ASI  
output data rate is 54 Mbps or less.  
Packet Mode  
The unit formats the ASI output in the packet mode when the selected ASI  
output data rate is greater than 54 Mbps.  
DSR-6400 Series  
43  
     
3
Reset Menu  
Use this menu to execute factory defaults, perform power cycle resets, view the current code  
version, and activate a different code version. Press the buttons until the Reset menu appears.  
  
RESET Reset Type  
No  
Code Select  
E
0x333 active  
Reset Type Field  
Default: No  
Press the button until the cursor is at the Reset Type label, and press ENTER to move into the  
4
field. Press the  
buttons to display the options: No, Factory Defaults, or Power Cycle.  
  
Factory Defaults Option  
Use the Factory Defaults option to reset the system to the programming values originally set by the  
factory firmware.  
CAUTION: Selecting this reset option deletes all defined setups and downloaded information.  
This operation interrupts service output, so use it carefully.  
Press ENTER. The following caution message appears and indicates that all programming will be  
lost if the action proceeds.  
CAUTION: IRD memory will be reset  
Press E to continue or  
to stop  
Press any arrow button (  
4  
) to back out of the field and leave it unchanged. Otherwise,  
press ENTER to proceed. The following message displays.  
Factory Default reset in progress..  
Power Cycle Option  
The Power Cycle option reboots the unit without losing internal user setup information or downloaded  
network information. Pressing ENTER causes the following caution message to appear.  
CAUTION: Reset will interrupt service  
Press E to continue or  
to stop  
Press any arrow button (  
) to back out of the field and leave it unchanged, or press  
ENTER to proceed. The following message displays:  
4  
Power Cycle reset in progress. . .  
Press E to continue or to stop  
44  
       
Code Select Field  
Default: 0xnnn active  
The unit can hold one or two version of code. Initially, the unit has just one version of code and that  
code is active and running inside the unit. When the unit receives and stores a second code version  
via a broadcast code download, the second code version is saved in memory, but is not activated.  
When code is pushed out to the unit, it is assigned a planned activation time. This is when the unit  
will automatically deactivate the original code version, install the newer code version, and reboot  
the unit with the new version code activated and running.  
Use the Code Select field to perform two necessary operations:  
Manually upgrade the unit to a newer code version, prior to the scheduled activation time  
Manually revert the unit to a previous code version that is still resident on the unit  
Press the button until the cursor is at the Code Select label, and press ENTER to move into the field.  
4
Use the  
buttons to display the various options within this field. The following four bullets  
  
describe how to use the Code Select field to perform the necessary operations.  
The Active selection (shown below) is not an executable option. However, it does display the  
current code version number that is active and running on the unit. The active selection  
always shows a code version number followed by the word: active.  
RESET Reset Type  
No  
Code Select  
E
0x333 active  
In this example, 0x333 represents the code version number that is currently running on this unit.  
Note: Choosing Active and pressing ENTER does not execute any changes on the unit.  
Choosing this selection and pressing ENTER will only return the cursor to the Code Select label.  
The two selections (five dashes as shown below and the five dashes followed by “available”) are  
not executable options. If either of these messages appear, it indicates the absence of a second code  
version on this unit. This means this unit cannot be reverted or upgraded to another code version  
until a new broadcast code download is received.  
RESET Reset Type  
No  
Code Select  
E
-----  
Note: Choosing ----- and pressing ENTER (or choosing ----- available and pressing ENTER)  
does not execute any changes on the unit. Choosing this selection and pressing ENTER will only  
return the cursor to the Code Select label.  
Available Option - This option is an executable option. If this option is listed in the unit’s menu  
system, this means the unit has an additional code version resident on the unit, but it is not  
currently active. The code version will either be a previous code version number or a newer  
code version.  
DSR-6400 Series  
45  
 
3
The following example shows a unit at version 0x333 that could be reverted to version 0x332.  
This example shows the active code is 333.  
RESET Reset Type  
No  
Code Select  
E
0x333 active  
If “available” is preceded by a smaller value  
than the active code value, then selecting this  
option will revert the unit to the previous code  
version. If it is necessary to revert a unit to a  
previous code version, this is typically  
performed manually, using the front-panel  
buttons. (A previous code version can also be  
installed by a broadcast countermand  
command, if the version is available.) For  
RESET Reset Type  
No  
Code Select  
E
0x332 available  
The following example shows a unit at version 0x333 that could upgraded to version 0x334.  
This example shows the active code is 333.  
RESET Reset Type  
No  
Code Select  
E
0x333 active  
If “available” is preceded by a larger value  
than the active code value, then selecting this  
option will upgrade the unit to the newer code  
version. Typically, the newer code will be  
activated automatically at the scheduled  
activation time. If it is necessary to manually  
upgrade this unit, see "To manually activate  
RESET Reset Type  
No  
Code Select  
E
0x334 available  
The Loading message is not an executable option. If a code broadcast download is currently  
in progress, the menu system will temporarily display a loading message, as shown below.  
RESET Reset Type  
No  
Code Select  
E
0x400 loading  
When the code download process is complete, the new code version is stored in the unit, the  
loading message is removed from the menu system, and the new code version is placed in the  
menu system and labeled “available.” The new code version will be executed at its planned  
activation time, unless the operator chooses to upgrade the unit manually, before the planned  
activation time.  
Note: Choosing this option and pressing ENTER does not execute any changes on the unit.  
Choosing this selection before the code download is complete will cause the unit to display  
the following warning message and will return the cursor to the Code Select label.  
Upgrade has not finished loading.  
46  
To manually activate an available code version (either revert or upgrade)  
Important: Use caution when executing the Available option. Once the Available option is  
selected and ENTER is pressed, the unit will make the specified code version as the current  
active version and will then perform an automatic reboot.  
1. Press the  
buttons to specify the Available option.  
  
2. Press the ENTER button.  
3. When the warning message appears, press ENTER to activate the specified  
code version.  
Or, if it is necessary to abort this process, press any arrow button (  
of the field and leave the unit unchanged.  
) to back out  
4  
Important: If the unit is being reverted to an older code version, the ----- selection (five  
dashes) will now replace the Available option within the menu system, and more importantly,  
the unit cannot return to the former code version. At this point, the only way to activate  
another code version is to wait for the next code download broadcast.  
Core Menu  
Press the  
buttons until the Core menu appears. Use this menu to change the LCD contrast.  
  
CORE  
Contrast  
E
18  
Contrast Field  
Default: 18  
To adjust the front-panel LCD contrast, press the button until the cursor is at the Contrast label,  
4
and press ENTER to move into the field. Use the arrow buttons (  
) to select a value between 0  
  
and 30, with 0 representing the least contrast and 30 the most contrast. Adjust the contrast so that the  
LCD panel can be read clearly. Press ENTER to confirm the selection and exit the field.  
Video Out Menu  
Press the  
buttons until the VIDEO OUT menu appears. Use this menu to modify the video  
  
output format. When the input to the uplink encoder is 525-line, the 525 field selects the unit analog  
video output, either NTSC or PAL-M. When the input to the uplink encoder is 625-line, the 625  
field selects the unit analog video output, either PAL 625 or PAL-N.  
VIDEO OUT 525 625  
E
NTSC PAL-625  
DSR-6400 Series  
47  
       
3
525 Field  
Default: NTSC  
Press the button until the cursor is at the 525 label, and press ENTER to move into the field.  
4
This field allows selection of the output format for 525-line video as either NTSC or PAL-M. Use  
the  
buttons to specify the desired option and press ENTER to confirm the selection.  
  
Pressing ENTER causes the following caution message to appear.  
CAUTION: Change will interrupt service  
Press E to continue or  
to stop  
Press any arrow button (  
ENTER to proceed.  
) to back out of the field and leave it unchanged, or press  
4  
625 Field  
Default: PAL-625  
Press the button until the cursor is at the 625 label, and press ENTER to move into the field.  
4
This field allows selection of the output format for 625-line video as PAL-625 or PAL-N. Use the  
buttons to specify the desired option and press ENTER to confirm the selection. Pressing  
  
ENTER causes the following caution message to appear.  
CAUTION: Change will interrupt service  
Press E to continue or  
to stop  
Press any arrow button (  
ENTER to proceed.  
) to back out of the field and leave it unchanged, or press  
4  
Firmware Menu  
Press the  
buttons until the Firmware menu appears. This menu displays the unit's firmware  
  
release information, which is equivalent to the product version number. This menu cannot be  
changed, but since the firmware is periodically updated, this menu confirms that the update was  
successful. This menu is used most commonly in troubleshooting. The High version value (shown  
below) is the current firmware version.  
FIRMWARE  
Boot:FPGA:High  
Upgrade  
000000  
E
XXXXXX:XXXXXX:XXXXX  
Boot:FPGA:High Field  
This field displays the version of boot, FPGA, and the high code. The boot code is loaded at the  
factory. The FPGA and high codes may be upgraded to later versions by a download that is  
delivered over the satellite signal from either the L-band or ASI input. The code versions are  
represented by a six-digit hexadecimal number. This field is non-editable.  
48  
       
Upgrade Field  
This read-only field displays the firmware code version that is set to be downloaded and activated  
(pending download). This field displays 000000 when no upgrade is in process. Pending upgrades  
are installed with an automatic activation and activation reboot that is scheduled by the system that  
is providing the upgrade.  
Important: Do not reboot/power cycle a unit in an attempt to activate the code ahead of the  
scheduled activation time. This will flush the upgrade from memory and restart the process.  
Download Menu  
Press the  
buttons until the DOWNLOAD menu appears. Use this menu to monitor the status  
  
of the current code download. This menu is used most commonly in troubleshooting.  
DOWNLOAD  
File Current Rcvd Total  
E
00 of 00 0000 0000 0000  
During a background code download, the unit collects the upgrade code in the background while  
concurrently decoding video and audio services. This menu may be selected anytime before, during,  
and after a background code download.  
File Field  
The File field consists of two sub-fields. The first sub-field is editable and selects, by index, a  
download file for monitoring. The second sub-field is non-editable and indicates the total number  
of files that have been downloaded and/or are available to be downloaded.  
Current Field  
This non-editable field pertains to the file selected in the File field and indicates the ID for the  
current segment received by the unit during the download of the file.  
Rcvd Field  
This non-editable field indicates the number of segments that the unit has received for the file  
selected in the File field.  
Total Field  
This non-editable field displays the ID for the last segment of the file selected in the File field.  
Note: When the unit completes the download process, all counters on this menu are reset to 0.  
DSR-6400 Series  
49  
           
3
DR Menu (Acquisition Recovery)  
Use this menu to review the Acquisition Recovery map. This menu is used most commonly in  
troubleshooting. Press the  
buttons until the DR menu appears.  
  
DR MODE  
E DISABLED  
VCT  
VCN  
PORT  
(00000) ---- NA  
MODE Field  
Default: DISABLED  
This non-editable field displays the DR modes:  
DISABLED  
CHANNEL  
Acquisition Recovery is off.  
The unit uses the virtual channel (provided by the uplink) to search  
for a live channel.  
XPNDR  
The unit uses the currently-defined transponder definitions from the  
uplink provider to search for a live frequency.  
VCT (Virtual Channel Table) Field  
Default: (00000)  
This non-editable field displays the Acquisition Recovery map’s Virtual Channel Table (VCT) number  
(0 to 65535) that is currently specified by the uplink programmer (BNC). If the VCT is not available,  
the unit displays (00000).  
VCN (Virtual Channel Number) Field  
Default: ----  
If this field is non-editable. The four dashes (----) designate that no virtual channels are currently  
being provided from the uplink provider.  
If the MODE field displays CHANNEL and the uplink provider is providing one or more valid  
maps, then this field displays the selection icon ( ). Use the up and down buttons (  
the list of channels that are currently being supplied by the uplink provider.  
) to view  
  
PORT Field  
Default: NA  
This non-editable field displays one of the following three messages:  
NA  
The VCT is either not available or the uplink provider set it to 00000.  
NOT DEFINED  
The decoder is not available to map a VCT or a configured port.  
This means the channel’s port is not configured.  
1,X0(20),H  
(example)  
Input port number (1-8) that is associated with the specified  
channel (followed by a comma), the Satellite name,  
the Satellite ID within brackets, (followed by a comma),  
the polarity specified with either H (for Horizontal)  
or V (for Vertical).  
50  
         
Channel Menus  
Press the  
buttons until the Channel menu appears. Use this menu to view or select active  
  
VCTs, Virtual Channels, and their corresponding transponder names.  
CHANNEL PR VCT  
00000  
CHNL Xpndr  
E
1
0000 (MPEG mode)  
PR Field (DSR-6402, DSR-6403, and DSR-6404 only)  
Default: 1  
The PR (processor) field does not appear on a DSR-6401. Press the button until the cursor is at the  
4
PR label, and press ENTER to move into the field. Press the  
buttons to scroll through the  
  
available processor values. Press ENTER to confirm the selection and exit the field. Each PR number  
has its own VCT and Channel (CHNL) fields, for manual assignment to each processor path.  
Note: Changing this value will change all other PR fields throughout this units menu system to  
the same value that is set here.  
VCT Field  
Use this field to select a Virtual Channel Table (VCT) number. Contact the program provider for  
the correct VCT number to enter for that encoder system. Press the button until the cursor is at  
4
the VCT label, and press ENTER to move into the field. While ensuring that the cursor remains  
on the up/down symbol ( ), press the  
buttons to scroll throughout the available VCTs. (If  
  
the network has four VCTs, then only four VCTs appear in this field.) Press ENTER to confirm  
the selection and exit the field.  
This field also provides a second method for entering the VCT. To edit the field, use the  
buttons to select the digit to change and then, while the cursor is on that digit, press the  
4  
  
buttons to display the required value. Repeat this process for each applicable digit. Press ENTER  
to confirm the selection and exit the field.  
If the following message appears after pressing ENTER, this field is currently under uplink  
control and cannot be changed from the front panel. Press any button to continue. If a unit is  
under uplink channel control, this field and CHNL field become read-only.  
Channel configured by uplink  
Press any button to continue  
CHNL Field  
Use the Channel field to select the Virtual Channel for the output service. The unit supports  
channel values from 0000 to 4095. Press the button until the cursor is at the Channel label, and  
4
press ENTER to move into the field. While ensuring that the cursor remains on the up/down  
symbol ( ), press the  
buttons to scroll through the available Virtual Channels. (If the chosen  
  
VCT contains twenty-four Virtual Channels, then only twenty-four Virtual Channels appear in  
this field.) Press ENTER to confirm the selection and exit the field.  
DSR-6400 Series  
51  
       
3
This field also provides a second method for entering the Virtual Channel(s). To edit the field, use  
the  
  
buttons to select the digit to change and then, while the cursor is on that digit, press the  
buttons to display the required value. Repeat this process for each applicable digit. Press  
4  
ENTER to confirm the selection and exit the field.  
If you are attempting to edit the configuration and the following message appears after pressing  
ENTER, this field is currently under uplink control and cannot be changed from the front panel.  
Press any button to continue. If a unit is under uplink channel control, this field and VCT field  
become read-only.  
Channel configured by uplink  
Press any button to continue  
If the unit’s configuration can be edited, the following caution messages appear:  
A caution message is displayed when changing from an MPEG program number selection to a  
Virtual Channel (DCII Selection Mode).  
CAUTION: Changing to DCII selection mode  
Press E to continue or  
to stop  
Press any arrow button ( ) to back out of the field and leave it unchanged. Otherwise,  
4  
press ENTER to proceed.  
If a Virtual Channel is selected that is not in the chosen VCT, then a warning message, “Not in  
map” is displayed to the right of the Virtual Channel.  
CHANNEL PR VCT  
00000  
CHNL Xpndr  
E
1
0000 (MPEG mode)  
Virtual Channels have designated satellite and polarity attributes. The unit cannot decode the  
chosen Virtual Channel until a port is set up with the applicable satellite and polarity  
information. For more details, see "Port Menu" on page 36. The unit uses these satellite and  
polarity attributes to determine which RF port to use. However, if a Virtual Channel is selected  
that does not match the satellite and polarity attributes of any port, then the unit is unable to  
determine which port to use and the following caution message is displayed.  
CAUTION: Channel dddd not present  
Press E to continue or  
to stop  
Press any arrow button (  
4  
) to back out of the field and leave it unchanged. Otherwise,  
press ENTER to proceed.  
52  
Xpndr Field  
This non-editable field displays the current (Xpndr) transponder name (alpha/numeric) that is  
downloaded. If a Virtual Channel is selected that is not in the chosen VCT, then a warning message,  
(Not in map) is displayed to the right of the Virtual Channel. This field serves as a label or identifier  
for the signal source.  
MPEG SELECT Menu  
Use this menu as an alternative to VCT and Channel (DCII Selection Mode) by specifying the  
MPEG program number(s). Press the buttons until the MPEG SELECT menu appears. The  
  
MPEG program number can be used instead of a Virtual Channel, but only if the unit is already  
tuned to the appropriate L-band, ASI, or GigE input signal.  
MPEG SELECT  
PR  
Program  
E
1
00000(Not in map)  
PR Field (DSR-6402, DSR-6403, and DSR-6404 only)  
Default: 1  
The PR (processor) field does not appear on a DSR-6401. Press the button until the cursor is at  
4
the PR label, and press ENTER to move into the field. Press the  
buttons to scroll throughout  
  
the available processor values. Press ENTER to confirm the selection and exit the field. Each PR  
number has its own Program field for manual assignment to each processor path.  
Note: Changing this value will change all other PR fields throughout this units menu system to  
the same value that is set here.  
Program Field  
Press the button until the cursor is at the Program label, and press ENTER to move into the  
4
field. While ensuring that the cursor remains on the up/down symbol ( ), press the  
buttons  
  
to scroll throughout the available MPEG programs. (If the current L-band or ASI input signal  
contains four MPEG programs, then only four MPEG programs appear in this field.) Press  
ENTER to confirm the selection and exit the field.  
This field also provides a second method for selecting the MPEG program(s). Use the  
buttons  
4  
buttons to  
to select the digit to change and then, while the cursor is on that digit, press the  
  
display the required value. Repeat this process for each applicable digit. Press ENTER to confirm  
the selection and exit the field.  
If you are attempting to edit the configuration and the following message appears after pressing  
ENTER, this field is currently under uplink control and cannot be changed from the front panel.  
Press any button to continue.  
Channel configured by uplink  
Press any button to continue  
DSR-6400 Series  
53  
       
3
If the unit’s configuration can be edited, the following caution messages appear:  
A caution message is displayed when changing from a Virtual Channel (DCII Selection Mode)  
to a MPEG program number (MPEG Selection Mode). Press any arrow button ( ) to  
4  
back out of the field and leave it unchanged. Otherwise, press ENTER to proceed.  
CAUTION: Changing to MPEG selection mode  
Press E to continue or  
to stop  
A caution message displays when an MPEG program number is selected which does not exist  
within the acquired source signal or transport stream.  
CAUTION: Program ddddd does not exist  
Press E to continue or  
to stop  
Press any arrow button ( ) to back out of the field and leave it unchanged. Otherwise,  
4  
press ENTER to proceed.  
AUD1LANG and AUD2LANG Menus  
CAUTION: Making changes to this menu will briefly interrupt all MPEG2 service outputs (ASI Out  
2 and GigE). When turned on, the ad insertion signals can be sent to the local headed equipment.  
These menus (Audio1 and Audio2 Language) have three fields to modify and view the status of  
the language for the Audio1 and Audio2 outputs. Also, use this menu to view the mode of the  
audio signal as it is received from the programmer and before any subsequent down mixing that  
the unit may perform. Press the  
or AUD2LANG).  
buttons until the desired menu appears (either AUD1LANG  
  
AUD1LANG Dspl Left  
All eng00  
Right InputMode  
eng00 ---  
E
AUD2LANG Dspl Left  
All eng00  
Right InputMode  
eng00 ---  
E
These menus also govern and display the audio tracks used when transcoding to MPEG2 video  
output via ASI OUT 2 output port and transcoded GigE output port. Up to two audio tracks are  
passed with each transcoded service (i.e., AUD1LANG and AUD2LANG).  
54  
 
Dspl Field  
Default: All  
Press the button until the cursor is at the Dspl (Display) label, and press ENTER to move into the  
4
field. Select the option that applies to the Left and Right. There are three options: All, Avail, and  
Status. Press the  
buttons to specify the desired option.  
  
All  
Use the arrow button ( ) to enter the three-letter code in the Left field. It may be  
4  
necessary to select languages that are not functional at this time, but will be functional in  
the future. Press ENTER to confirm the selection and exit the field.  
Recommended  
Avail  
Use the Available option to scroll only through the languages present within the source,  
while the cursor is in the Left (which matches the Right field). If the active service has  
only three languages, as listed for the Virtual Channel or program, only three appear. If  
the user changes the service, the available languages may also change. Press ENTER to  
confirm the selection and exit the field.  
Status Use the Status option to view the actual audio language. The actual language can  
differ from the chosen language. This may occur when the user’s choice for language  
is unavailable. The bullets in the next topic describe the rules that govern which  
language is used.  
Left and Right Fields  
Press the button until the cursor is at the Left label, and press ENTER to move into the field. If the  
4
Dspl field is set to All and the AudioMix field (described on page page 38) is set to Dual Mono, then  
Left and Right will have separately editable fields. Otherwise, they are controlled together as a pair  
from the Left field alone.  
Also use these fields to set the language through the following three options:  
Any language, if the language is set to All.  
The currently available languages, if the Dspl is set to Avail.  
def (default), if the Dspl field is set to either All or Avail. Press the  
buttons to specify the  
  
desired option. Press ENTER to confirm the selection and exit the field.  
The following bullets describe the rules that govern which language is used:  
If def (default) is selected, the Audio 1 and Audio 2 outputs default to the first and second  
language, respectively, that is listed for the service.  
If the AudioMix field (described on page 38) is set to Surround, Stereo, or Mono and the  
user’s choice for language is not available, the audio output is the default language.  
If the AudioMix field (described on page 38) is set to Dual Mono and a language pair is not  
available that matches the user’s choice for Left and Right languages, the unit selects and  
outputs the first occurrence of the Left language choice. The system cannot take a Left from  
one audio pair and a Right from another. If there is no match for the Left language choice, the  
unit uses the default language.  
DSR-6400 Series  
55  
     
3
There is an interaction between the Language (Lang) menu and the AudioMix field (described  
on page 38): If the user had previously selected Stereo or Mono in the AudioMix field and a  
specific language as the audio output in the Lang menu, but later changes the AudioMix menu  
setting to Dual Mono, the Dual Mono changes in this menu to the same language specified for  
both Dual Mono channels and a caution screen displays. After changing the AudioMix menu  
to Dual Mono, reselect the languages desired here, in this menu.  
If the user previously selected Dual Mono in the AudioMix field with two different languages  
as audio outputs in the Language menu, but later selects Stereo, Stereo Surround, or Mono in  
the AudioMix field, the output in this Language menu defaults to the first occurrence of a  
specified language (the one defined for the Left channel first, then for Right channel if there is  
no match for the Left). In this case, the same caution screen appears.  
InputMode Field  
This read-only field indicates the incoming audio mode of the active service.  
Text Lang Menu  
Implemented  
In Future  
Release  
Use this menu to modify and view the status of the language of the video subtitles. Press the  
buttons until the Text Lang (Text Language) menu appears.  
  
TEXT LANG Display  
E
Off  
Display Field  
Default: Off  
Press the button until the cursor is at the Display label and press ENTER to move into the field.  
4
This field has the following four options:  
Off  
This option disables subtitles. Press ENTER to confirm the selection and exit the field.  
Status Use this option to view the actual text language. The actual language can differ from the  
chosen language when the user’s choice for language is unavailable. The bullets at the  
bottom of page 55 describe the rules that govern which language is used. Press ENTER  
to confirm the selection and exit the field.  
Recommended  
Avail Use the Available option to scroll through the languages supported by the system  
while the cursor is in the field. Furthermore, selection of this option allows you to  
scroll through only the languages available for the active service. (If the active  
service has only three languages, as listed for the Virtual Channel or program, only  
three appear. If the user changes the service, the number of languages may also  
change.) Press ENTER to confirm the selection and exit the field.  
All  
Use this option to enter the desired subtitle language in the Subtitle field which may  
or may not be present in that service. You may wish to select languages that are not  
functional at this time, but will be functional in the future. Press ENTER to confirm  
the selection and exit the field.  
56  
     
Subtitle Field  
Default: def  
Press the button until the cursor is at the Subtitle label, and press ENTER to move into the field.  
4
TEXT LANG Display  
All  
Subtitle  
E
def  
Use one of the following options to set the language:  
If the Display is set to All, use the Subtitle field to specify any language. Use the arrow button  
) to enter the three-letter code.  
(
4  
If the Display is set to Avail, the Subtitle field can display the currently available languages.  
buttons to specify the desired option. Press ENTER to confirm the selection and  
Press the  
  
exit the field.  
Note: If the Display field is set to Status, use the read-only Subtitle field to view the current language.  
IP Menus  
Use the IP menus to configure the 10/100 and GigE ports.  
10/100 MAC Address Menu  
Use the following procedure to view the 10/100 MAC address for the left Ethernet port on the  
back panel of the unit. Press the  
buttons until the 10/100 MAC Address menu appears. This  
  
menu displays the Ethernet port’s MAC address. The address is represented in a hexadecimal  
format and it is not editable.  
PORT 10/100  
MAC Address  
E
hh-hh-hh-hh-hh-hh  
DSR-6400 Series  
57  
     
3
10/100 DHCP Menu  
Press the  
buttons until the Port 10/100 DHCP menu appears. The front panel screen displays  
  
the DHCP and Unit Name fields. DHCP (Dynamic Host Configuration Protocol) allows the Satel-  
lite Multiplex Decrypter to obtain a set of IP parameters from a DHCP server. The DHCP server  
ensures that all these IP addresses are unique. This automates and facilitates the unit's access to the  
network. The management of the IP address pool, in this case, is handled by the server, and not by a  
human administrator.  
PORT 10/100  
DHCP  
Unit Name  
E
Disable DSR640X-XXXXX  
DHCP Field  
Default: Disable  
Move into the field and choose either Enable or Disable.  
Unit Name Field  
Default: DSR-640X-XXXXX  
The Unit Name is fully editable. It is placed into the outgoing DHCP request and is used for registra-  
tion. The Unit Name, in most cases, is only a suggestion to the DHCP server and may be updated with  
a different name upon receiving the DHCP registration reply. If an updated name is received from a  
DHCP server, the Unit Name will be adjusted to show this change and will replace the user-entered  
name. The default name is DSR640X-XXXXX. The XXXXX is the unit’s unique five-digit address.  
10/100 IP Address Menu  
Default: 192.168.000.100  
Use the following procedure to set and view the IP address for the left Ethernet port on the back  
panel of the unit. Press the  
buttons until the IP Address menu appears. Use this menu to  
  
enter an IP address for the Ethernet port. The address is represented in the common dotted-  
decimal format. Contact the network administrator for details about configuring the Ethernet port  
for operation on your local network.  
PORT 10/100  
IP Address  
E
192.168.000.100  
Important: Do not configure the IP Address of the 10/100 and GigE to be on the same subnet.  
Press the button until the cursor is at the IP Address label, and press ENTER to move into the  
4
field. Use the arrow buttons (  
) to enter the desired address and then press ENTER to  
4  
confirm the selection and exit the field.  
58  
         
10/100 Subnet Mask Menu  
Default: 255.255.255.000  
Use the following procedure to set and view the Subnet Mask address for the left Ethernet port on  
the back panel of the unit. Press the buttons until the Subnet Mask menu appears. The subnet  
  
mask is represented in the common dotted-decimal format. Contact the network administrator for  
details about configuring the Ethernet port for operation on your local network.  
PORT 10/100  
Subnet Mask  
E
255.255.255.000  
Press the button until the cursor is at the Subnet Mask label, and press ENTER to move into the  
4
field. Use the arrow button ( ) to enter the desired address and then press ENTER to confirm  
4  
the selection and exit the field.  
10/100 Default Gateway Menu  
Default: 192.168.000.001  
Use the following procedure to set and view the Default Gateway address for the left (10/100)  
Ethernet port on the back panel. Press the buttons until the 10/100 Default Gateway menu  
  
appears. The IP Gateway is an address that is represented in the common dotted-decimal format.  
Contact the network administrator for details about configuring the Ethernet port for operation on  
your local network.  
PORT 10/100  
Default Gateway  
E
192.168.000.001  
Press the button until the cursor is at the 10/100 Default Gateway label, and press ENTER to  
4
move into the field. Use the arrow buttons (  
) to enter the desired gateway address and  
4  
press ENTER to confirm the selection and exit the field.  
Port GigE MAC Address Menu  
Default: hh:hh:hh:hh:hh:hh  
To view the GigE MAC address for the right Ethernet port on the back panel, press the  
  
buttons until the Port GigE menu appears. The address is represented in a hexadecimal format and  
it is not editable.  
PORT GigE  
MAC Address  
E
hh:hh:hh:hh:hh:hh  
DSR-6400 Series  
59  
         
3
GigE IP Address Menu  
Default: 192.168.054.100  
Use the following procedure to set and view the GigE IP output address for the right Ethernet port  
on the back panel of the unit. Press the buttons until the GigE IP Address menu appears. The  
  
address is represented in the common dotted-decimal format. Contact the network administrator  
for details about configuring the GigE port for operation on your local network.  
PORT GigE  
IP Address  
E
192.168.054.100  
Important: Do not configure the IP Address of the 10/100 and GigE to be on the same subnet.  
Press the button until the cursor is at the IP Address label, and press ENTER to move into the  
4
field. Use the arrow buttons (  
) to enter the desired address and then press ENTER to  
4  
confirm the selection and exit the field.  
GigE Subnet Mask Menu  
Default: 255.255.255.000  
Use the following procedure to set and view the GigE Subnet Mask for the right Ethernet port on  
the back panel of the unit. Press the buttons until the GigE Subnet Mask menu appears. The  
  
GigE subnet mask is represented in the common dotted-decimal format.  
Contact the network administrator for details about configuring the GigE port for operation on  
your local network.  
PORT GigE  
Subnet Mask  
E
255.255.255.000  
Press the button until the cursor is at the Subnet Mask label, and press ENTER to move into the  
4
field. Use the arrow button (  
) to enter the desired address and then press ENTER to  
4  
confirm the selection and exit the field.  
GigE Default Gateway Menu  
Default: 192.168.054.002  
Use the following procedure to set and view the GigE Default Gateway address for the right  
Ethernet port on the back panel of the unit. Press the buttons until the GigE Default  
  
Gateway Address menu appears. The GigE Default Gateway is an address that is represented in  
the common dotted-decimal format. Contact the network administrator for details about  
configuring the GigE port for operation on your local network.  
PORT GigE  
Default Gateway  
E
192.168.054.002  
60  
     
Press the button until the cursor is at the GigE Default Gateway label, and press ENTER to  
4
move into the field. Use the arrow buttons (  
) to enter the desired address and then press  
4  
ENTER to confirm the selection and exit the field.  
GigE TS Mode Menu  
Press the  
buttons until the Port GigE TS Mode menu appears. Use this menu to select which  
  
transport streams are routed to the GigE port and if the DSMCC data is also routed to the GigE port.  
PORT GigE TS Mode  
Off  
DSMCC  
E
Off  
TS Mode Field  
Default: Off  
Press the button until the cursor is at the TS Mode label, and press ENTER to move into the  
4
field. Press the  
buttons to choose one of the four options: Off, Transcoded, Passthru, or  
  
Transcoded+Passthru. When Passthru is selected, a copy of the ASI OUT 1 transport stream is  
routed to the GigE port. When Transcoded is selected, a copy of the ASI OUT 2 transport stream  
is routed to the GigE port. When Transcoded+Passthru is selected, a copy of both ASI OUT 1 and  
ASI OUT 2 are routed to the GigE port. Press ENTER to confirm the selection and exit the field.  
DSMCC Field  
Default: Off  
DSMCC data is IP data that is carried in the MPEG stream from the programmer. It is part of a  
programmer service and different programmer services may carry the same or different DSMCC  
data. The unit extracts the DSMCC data and outputs it as an IP stream from the GigE port.  
Press the button until the cursor is at the DSMCC label, and press ENTER to move into the field.  
4
  
Press the  
buttons to choose either Off or On. When On is selected, the unit outputs only the  
DSMCC data from the first processor path (PR1). DSMCC data is not usually continuous, and so  
the unit only outputs DSMCC data when DSMCC data is present in the programmer service that is  
handled by the first processor. DSMCC data from other processor paths 2, 3, or 4 is disregarded.  
Press ENTER to confirm the selection and exit the field. When Off is selected, the unit does not  
output DSMCC data.  
GigE Output Transport Streams  
Transcoded and Passthru transport streams are separate and unique streams that can share the one  
physical GigE output port. The next two Port GigE IP menus described in this section provide a way  
to route each of these streams.  
DSR-6400 Series  
61  
       
3
GigE Xcoded Dest Addr Menu  
Use this menu to set the GigE transcoded destination address and the associated port. This menu  
is only operational if the TS Mode field is set to either Transcoded or Transcoded+Passthru. Press  
the  
buttons until the Port GigE Xcoder Dest Addr menu appears.  
  
PORT GigE Xcoded Dest Addr  
192.168.054.201  
Port  
E
06100  
Xcoded Dest Addr Field  
Default: 192.168.054.201  
Press the button until the cursor is at the Xcoded Dest Addr label, and press ENTER to move into  
4
the field. Use the arrow button (  
) to enter the desired address and press ENTER to confirm  
4  
the selection and exit the field.  
Port Field  
Default: 06100  
Press the button until the cursor is at the Port label, and press ENTER to move into the field.  
4
Use the arrow button (  
) to enter the desired value and then press ENTER to confirm the  
4  
selection and exit the field.  
GigE PassThru Dest Addr Menu  
Use this menu to set the GigE pass through destination address and the associated port. This menu  
is only operational if the TS Mode field is set to either Passthru or Transcoded+Passthru. Press the  
buttons until the Port GigE PassThru Dest Addr menu appears.  
  
PORT GigE PassThru Dest Addr  
192.168.054.200  
Port  
E
06000  
PassThru Dest Addr Field  
Default: 192.168.054.200  
Press the button until the cursor is at the PassThru Dest Addr label, and press ENTER to move  
4
into the field. Use the arrow button (  
) to enter the desired address and then press ENTER  
4  
to confirm the selection and exit the field.  
Port Field  
Default: 06000  
Press the button until the cursor is at the Port label, and press ENTER to move into the field.  
4
Use the arrow button (  
) to enter the desired value and then press ENTER to confirm the  
4  
selection and exit the field.  
62  
           
Status Display Menus  
Status display menus provide information regarding the current status of the unit. These fields are  
not editable, and the displayed information is either (1) the result of changes in an installation or  
channel selection menu, or (2) a parameter the unit reports as part of its operation.  
Status0 Menu  
Press the  
buttons until the Status0 menu appears.  
  
STATUS0 Health  
Acq:Alarm  
Alarm Trigger  
Auto  
E
Health Field  
This status-only field displays the following status conditions. Press the button until the cursor is at  
4
the Health label, and press ENTER. Use the  
buttons to scroll through the following health  
  
indicators. The unit displays the OK or Alarm status of each health indicator.  
Acq  
Acquisition indicates whether the unit is locked to the incoming signal  
(OK) or not (Alarm).  
Auth  
Xcdr  
HDD  
Video  
Authorization indicates whether the unit has authorization (OK) or not  
(Alarm) to process all of the selected programs.  
Indicates whether the transcoding status of all programs is OK or whether  
one or more transcoding processors have detected an alarm condition.  
Indicates whether the memory storage device is properly functioning  
(OK) or not (Alarm).  
Indicates whether the unit is able to render analog composite video (OK)  
or not (Alarm).  
Fan  
Indicates whether all fans are operating (OK) or not (Alarm).  
Alarm Trigger Field  
The Alarm Trigger field is non-editable and displays the alarm trigger condition that is entered in  
the Trigger Field in the Alarm Menu (described on page 41).  
DSR-6400 Series  
63  
       
3
Status1 Menu  
Press the  
buttons until the Status1 menu appears.  
  
STATUS1 FrontPanel  
Local-Control  
Input Type  
L-Band  
E
FrontPanel Field  
This status-only field displays whether the user is able to control the unit completely from the  
front panel or whether some front-panel functions are disabled. When this field displays Local-  
Control, this means the panel is not locked and the local user has access to all menu functions. All  
menus and fields operate as described in this manual. When Locked-Out is displayed, access to  
front-panel control is disabled by the Uplink Programmer.  
Input Type Field  
This status-only field displays the input connector on which the active signal is received. This  
field displays one of three messages:  
L-Band This designates the input source (from RF Port 1 to RF Port 8 on the back panel).  
ASI This designates the input source is from ASI In port on the back panel.  
GigE-In This designates the input source is from GigE In port on the back panel.  
64  
     
Status2 Menu  
This menu only applies to RF input. Press the  
buttons until the STATUS2 menu appears. This  
  
screen displays the source name, channel number, and the signal quality of the incoming signal.  
STATUS2 Source  
---  
Channel  
----  
Quality  
---  
E
Source Field  
This status-only field displays the source name, which was entered by the programmer or network  
operator at the encoder/uplink to identify the source. Dashes are displayed when no information  
is available.  
Channel Field  
This status-only field displays the selected Virtual Channel number (from the Channel menu).  
Dashes are displayed when no information is available.  
Quality Field  
This status-only field displays a number from 1 to 100 so that the quality level of the signal can be  
judged. The signal quality is also displayed as a large bar graph in the Status3 menu. If it is 35 or  
less, take action at your site to increase the dish size or improve the Low Noise Block (LNB) to  
prevent occasional loss of output.  
Status3 Menu  
This menu only applies to RF input. Press the  
buttons until the STATUS3 menu appears. This  
  
screen displays the quality level of the signal as a large bar graph that expands to fill the entire LCD  
screen. The following example shows the quality at about 75.  
STATUS3 Signal Quality  
E
|||||||||||||||||||||||.......  
DSR-6400 Series  
65  
         
3
Status4 Menu  
This menu only applies to RF input. Press the  
buttons until the STATUS4 menu appears. This  
  
screen displays the satellite name and signal tuning characteristics.  
STATUS4 Sat Freq  
Symb Code Format  
E
--- 1430.00 11.71 5/6 Comb  
Sat Field  
This status-only field displays the satellite name from the downloaded network information.  
Dashes (---) are displayed when no information is available.  
Freq Field  
This status-only field displays the downlink frequency of the L-band signal. This may be different  
from the frequency that was initially set in the Manual Tune menu.  
Symb Field  
This status-only field displays the symbol rate (megasymbols per second) of the L-band signal.  
Dashes (---) indicate that no information is available.  
Code Field  
This status-only field displays the code rate (Error Control Coding for Forward Error Correction)  
of the L-band signal.  
Format Field  
This status-only field displays the format of the L-band signal. The field displays either Comb  
(Combined) or Split. Dashes (---) are displayed when no information is available.  
Status5 Menu  
This menu only applies to RF input. Press the  
buttons until the STATUS5 menu appears. This  
  
screen displays the sync, Eb/No, and authorization state of the unit.  
STATUS5 Sync Eb/No Authorize State  
E
Tuning -2.0  
Undefined Service  
66  
             
Sync Field  
This status-only field displays the acquisition Sync state. The Sync state can be either Locked  
or Tuning.  
Eb/No Field  
This status-only field displays a value from 0.0 to 35.0 that designates a measurement of the  
signal-to-noise ratio.  
Authorize State Field  
This status-only field displays the authorization state of the currently-selected channel. This field  
indicates how the Satellite Multiplex Receiver/Transcoder is authorized. If the Authorization State is  
Not Authorized, the field will alternate, and display a reason why it is not authorized (e.g., Missing  
Map). Table 3-1 describes each authorization state.  
Table 3-1: Authorization States  
Authorize State  
Description  
Missing Map  
Incorrect Virtual Channel Table Number  
Undefined Channel  
Undefined Service  
Unencrypted  
Incorrect Virtual Channel Number  
Incorrect Service Number  
Service is not Encrypted  
Unknown  
Unknown State  
No Program Rekey  
No Working Key  
No Event Blackout  
No Category Key  
Old Category Seq  
Subscrb With Tape  
Subscrb w/o Tape  
Bad Seed Chksum  
Not Subscribed  
Regional Blackout  
Event Blackout  
Program Rekey Message is Missing  
Working Key Epoch Message is Missing  
Event Blackout Message is Missing  
Missing Category Key is Missing  
Old Category Sequence in Program Rekey Message  
Subscribed With Taping  
Subscribed Without Taping  
Bad Seed Checksum  
Not Subscribed  
Regional Blackout  
Event Blackout  
Circular Blackout  
Circular Blackout  
DSR-6400 Series  
67  
       
3
Status6 Menu  
Press the  
buttons until the STATUS6 menu appears. This screen displays the unit’s volatile  
  
memory, flash memory, and hard drive memory.  
STATUS6 Memory  
8.0MB  
Flash  
Hard Drive  
E
450.4MB 14.9GB  
Memory Field  
This status-only field displays the amount of free volatile memory in MB units that is available  
for use by the operating system.  
Flash Field  
This status-only field displays the amount of free non-volatile memory in MB units that is  
available for use by the operating system.  
Hard Drive Field  
This status-only field displays the amount of free space in GB units that is available for use by the  
operating system.  
68  
       
Status7(SD) Menu  
Press the  
buttons until the Status7 SD menu appears. This screen displays the video encoding  
  
configuration for the SD program.  
STATUS7 SD PR Vido Frmt Resolutn BitRt  
1 MPEG-2 720x480 6.0M  
E
PR Field (DSR-6402, DSR-6403, and DSR-6404 only)  
Default: 1  
The PR (processor) field does not appear on a DSR-6401. Press the button until the cursor is at  
4
the PR label, and press ENTER to move into the field. While ensuring that the cursor remains on  
the up/down symbol ( ), press the  
buttons to scroll throughout the available processor  
  
values. Press ENTER to confirm the selection and exit the field.  
Note: Changing this value will change all other PR fields throughout this units menu system to  
the same value that is set here.  
Vido Frmt Field and Resolution Field  
These fields indicates the video compression standard and the display resolution of the transcoded  
video. This is represented as the number of distinct pixels in the horizontal dimension and the  
number of scan lines.  
Note: The Video Resolution field does not include a designation for (p) progressive or  
(i) interlaced to denote the scan type for the SD video.  
BitRt Field  
The Bit Rate field indicates the data rate of the transcoded video.  
DSR-6400 Series  
69  
       
3
Status8(SD) Menu  
Press the  
buttons until the Status8 SD menu appears. This screen displays the audio encoding  
  
configuration for the transcoded SD program.  
STATUS8 SD PR Aud Format Mode  
BitR  
---  
E
1
0
PSTHRU ---  
PR Field (DSR-6402, DSR-6403, and DSR-6404 only)  
Default: 1  
The PR (processor) field does not appear on a DSR-6401. Press the button until the cursor is at  
4
the PR label, and press ENTER to move into the field. While ensuring that the cursor remains on  
the up/down symbol ( ), press the  
buttons to scroll throughout the available processor  
  
values. Press ENTER to confirm the selection and exit the field.  
Note: Changing this value will change all other PR fields throughout this units menu system to  
the same value that is set here.  
Aud Field  
Default: 0  
Use the Aud (Audio) field to choose which audio channel to display the status. Press the button  
4
until the cursor is at the Audio field, then use the  
buttons to choose the first audio channel (0)  
  
or the second audio channel (1). Press ENTER to confirm the selection and exit the field.  
Format Field  
This field is always set to PSTHRU (pass-through) and cannot be changed.  
Mode Field  
The Mode field indicates the mode (stereo or mono) of the audio for the selected audio channel.  
Dashes (---) designate no information is available.  
BitR Field  
The BitR (Bit Rate) field indicates the data rate of the transcoded audio. Dashes (---) designate no  
information is available.  
70  
           
Status9(HD) Menu  
This screen displays the video encoding configuration for the transcoded HD program. Press the  
buttons until the Status9 HD menu appears.  
  
STATUS9 HD PR Vido Fmt Resolutn BitRt  
E
1 MPEG-2  
1280x720 18.0M  
PR Field (DSR-6402, DSR-6403, and DSR-6404 only)  
Default: 1  
The PR (processor) field does not appear on a DSR-6401. Press the button until the cursor is at  
4
the PR label, and press ENTER to move into the field. While ensuring that the cursor remains on  
the up/down symbol ( ), press the  
buttons to scroll throughout the available processor  
  
values. Press ENTER to confirm the selection and exit the field.  
Note: Changing this value will change all other PR fields throughout this units menu system to  
the same value that is set here.  
Vido Fmt Field  
The Video field indicates the format of the incoming video, either MPEG-2 or MPEG-4.  
Resolutn Field  
The Video Resolution field is read-only and indicates the display resolution of the transcoded  
video. This is represented as the number of distinct pixels in the horizontal dimension and the  
number of scan lines.  
Note: The Video Resolution field does not include a designation for (p) progressive or  
(i) interlaced to denote the scan type for the HD video.  
BitRt Field  
The BitRt (Bit Rate) field indicates the data rate of the transcoded video.  
Status10(HD) Menu  
This screen displays the audio encoding configuration for the transcoded HD program. Press the  
buttons until the Status10 HD menu appears.  
  
STATUS10 HD PR Aud Format Mode BitR  
E
1
0
PSTHRU ---  
---  
DSR-6400 Series  
71  
           
3
PR Field (DSR-6402, DSR-6403, and DSR-6404 only)  
Default: 1  
The PR (processor) field does not appear on a DSR-6401. Press the button until the cursor is at  
4
the PR label, and press ENTER to move into the field. While ensuring that the cursor remains on  
the up/down symbol ( ), press the  
buttons to scroll throughout the available processor  
  
values. Press ENTER to confirm the selection and exit the field.  
Note: Changing this value will change all other PR fields throughout this units menu system to  
the same value that is set here.  
Aud Field  
Default: 0  
Use the Audio field to choose which audio channel to display the status. Press the button until  
4
the cursor is at the Audio field, then use the  
buttons to choose the first audio channel (0) or  
  
the second audio channel (1). Press ENTER to confirm the selection and exit the field.  
Format Field  
This field is always set to PSTHRU (pass-through) and cannot be changed.  
Mode Field  
The Mode field indicates the mode (stereo or mono) for the selected audio channel. Dashes (---)  
designate no information is available.  
BitR Field  
The BitR (Bit Rate) field indicates the data rate of the transcoded audio. Dashes (---) designate no  
information is available.  
Status11 Menu  
This status-only screen displays the multicast IP Address and Link status of the GigE input when  
receiving a transport stream input. Press the  
buttons until the Status11 menu appears.  
  
STATUS11 Addr Field  
Link Field  
Off  
E
----------  
Addr Field  
This status-only field displays the multicast IP address (range 224.000.000.000 to  
239.255.255.255) that is currently used to receive an input transport stream in the common  
dotted-decimal format. Dashes (---) designate no information is available.  
Link Field  
This status-only field indicates the connection speed (10, 100, or 1000 Mbps) of the GigE port.  
Off indicates that there is no connection to an Ethernet network.  
72  
               
Status12 Menu  
The mail messages are typically sent from the Uplink Provider and are usually about network issues  
(e.g., scheduled blackouts and code downloads). These messages can also be reviewed from the Fast  
Facts 8 OSD screen (described on page 96). Press the buttons until the Status12 menu appears.  
  
To view the messages remotely from the units web browser, see "Remote Operation" on page 21.  
STATUS12 MAIL: INBOX  
> 0/0  
E
Use the Status12 menu to view the Inbox mail messages along with their delivery timestamp. To  
move into the field, press and use the  
4
buttons to scroll through the mail messages.  
  
STATUS12 MAIL: INBOX  
> 2/5  
E 11/04/2011 21:17:50: A code download  
If it is necessary to view an entire message, press ENTER and use the  
through the message, two lines at a time.  
buttons to scroll  
  
is scheduled for 11/07/11 at 17:00. This  
will be the last download until we can  
To exit the message and return to the Status12 Menu, press ENTER.  
When the following message appears, choose to either move the message to the Archive list  
(press ENTER) or keep it in the Inbox (press any arrow button [ ]). To exit the menu,  
4  
press and ENTER.  
Do you want to mark message as read?  
Press E to continue or to stop  
Pointer and Quantity Fields  
The unit displays two values separated by a slash ( / ). The first value is the Pointer field and this is the  
message number being display on the front panel. The second value is the Quantity field and this is the  
number of mail messages that are currently in the Inbox. For example, 2/5 indicates that message 2 is  
currently being displayed and a total of 5 messages are currently in the Inbox.  
Note: The unit will maintain up to 300 mail messages between the Status12 menu (Inbox mail  
st  
messages) and Status13 menu (Archived messages). For example, when the 301 message  
arrives, the oldest message is then automatically purged. The unit, therefore, maintains the most  
recent 300 mail messages. Performing a factory reset will delete all messages from the decoder.  
DSR-6400 Series  
73  
   
3
Timestamp and Message Fields  
When a message is being displayed (as shown below), the menu’s second line displays a  
timestamp showing the date and time that the message was received at the decoder. A colon (:)  
separates the timestamp from the first few words of the message.  
STATUS12 MAIL: INBOX  
> 2/5  
E 11/04/2011 21:17:50: A code download  
Status13 Menu  
The messages in this menu are the mail messages that were originally in the Inbox (Status 12) and  
were manually moved to this location, the archive box (Status 13). Press the buttons until  
  
the Status13 menu appears. These messages can also be reviewed from the Fast Facts 9 OSD  
screen (described on page 97). To view the messages remotely using the units web browser, see  
STATUS13 MAIL: ARCHIVE > 0/0  
E
Use the Status13 menu to view archived mail messages, two lines at a time. To do this, press  
4
and use the  
buttons to scroll through the archived mail messages. If it is necessary to view  
  
an entire message, press ENTER and use the  
buttons to scroll through the message, two  
  
lines at a time. To exit the message, press ENTER. To exit the menu, press and ENTER.  
Pointer and Quantity Fields  
The unit displays two values separated by a slash ( / ). The first value is the Pointer field and this is  
the message number being display on the front panel. The second value is the Quantity field and this  
is the number of mail messages that are currently in the archive. For example, 2/5 indicates that  
message 2 is currently being displayed and a total of 5 messages are currently in the archive.  
Note: The unit will maintain up to 300 mail messages between the Status12 menu (Inbox mail  
st  
messages) and Status13 menu (Archived messages). For example, when the 301 message  
arrives, the oldest message is then automatically purged. The unit, therefore, maintains the most  
recent 300 mail messages. Performing a factory reset will delete all messages from the decoder.  
Timestamp and Message Fields  
When a message is being displayed (as shown below), the menu’s second line displays a  
timestamp showing the date and time the message was moved to the archive. A colon (:) separates  
the timestamp from the first few words of the message.  
STATUS13 MAIL: ARCHIVE  
> 4/7  
E 11/01/2011 21:17:50: A blackout is  
.
74  
       
Diagnostic Menus  
Use the unit's diagnostic menu to acquire information for troubleshooting purposes. The menus  
also provide test waveforms and use other diagnostic information displayed on an NTSC  
television monitor connected through the back panel’s Video and OSD Video port. Press the  
buttons until the DIAGNOSTIC menu appears.  
  
DIAG Menus  
Off  
PR  
E
1
Menus Field  
Default: Off  
Use the Menus field to enable or disable the on-screen diagnostics. Press the button until the  
4
cursor is at the MENUS label, and press ENTER to move into the field. Press the  
  
scroll to the desired screen. Press ENTER to confirm the selection and exit the field.  
buttons to  
Notice that if the Menus field is set to any option other than Off, Diag F, or Diag G; the Clear Cntrs  
(Clear Counters) field also appears.  
DIAG  
Menus  
Clear Cntrs PR  
No  
E
Fact 1  
1
Use the  
buttons to choose the desired option (Fast Facts 1 through 5 or Diag A through Diag G)  
  
and press ENTER to confirm the selection and exit the field. For more information about Fast Facts  
Clear Cntrs Field  
Use this field to reset selected counters to zero. This field is primarily for use with hotline troubleshoot-  
ing, and it is recommended that it be used only when so directed and does not affect the unit’s opera-  
tion, but it may give misleading troubleshooting results. To clear counters, press the button until the  
4
cursor is at the Clear Cntrs label, and press ENTER to move into the field. Press the button to select  
Yes and press ENTER to reset the counters to zero and return the field to No.  
PR Field (DSR-6402, DSR-6403, and DSR-6404 only)  
Default: 1  
The PR (processor) field does not appear on a DSR-6401. Press the button until the cursor is at  
4
the PR label, and press ENTER to move into the field. While ensuring that the cursor remains on  
the up/down symbol ( ), press the  
buttons to scroll throughout the available processor  
  
values. Press ENTER to confirm the selection and exit the field.  
Note: Changing this value will change all other PR fields throughout this units menu system to  
the same value that is set here.  
DSR-6400 Series  
75  
       
3
Unit Address Menu  
Press the  
buttons until the UNIT ADDRESS menu appears. This read-only menu displays the  
  
unit's 16-digit electronic address (range: 000-00000-00000-000 to 999-99999-99999-999). The  
program provider uses this address to identify a specific unit for authorization and retune  
messages. The display enables the user to view the address from the front panel rather than  
reading the label on the back panel.  
UNIT ADDRESS  
E
ddd-ddddd-ddddd-ddd  
TV Pass Card Menu  
®
The unit does not initially require a TV Pass Card , but if one is required, the program provider  
typically supplies one. The program provider uses the TV Pass Card address and unit address to  
identify a specific unit for authorization messages. Press the  
menu appears.  
buttons until the TV Pass Card  
  
TV PASS CARD Status  
E
Not Inserted  
Use this menu to view the TV Pass Card address from the front panel of the unit. There are three  
Status field options:  
Not Inserted  
xxx-xxxxx-xxxxx-xxx (a unique TV Pass Card address, range: 000-00000-00000-000 to  
999-99999-99999-999)  
xxx-xxxxx-xxxxx-xxx Needs Mating  
Audio Test Signal Menu  
Use this menu to validate audio connection by transmitting internally-generated audible tones to the  
audio output ports.  
AUDIO TEST SIGNAL L1/R1  
Off  
L2/R2  
E
Off  
Caution: This selection replaces audio.  
76  
     
L1/R1 and L2/R2 Fields  
Default: Off  
Use the appropriate field (either L1/R1 or L2/R2) to choose one of the following test tones:  
1000  
4040, 3960 (two tones)  
At the completion of the test, press ENTER to disable the test, exit the field, and return the field to  
the default setting (Off).  
Video Test Signal Menu  
Press the  
buttons until the Video Test Signal menu appears. Use the full-field video test  
  
signal to display different test patterns by selecting options within the Pattern field. This affects  
both video ports (Video and OSD Video).  
VIDEO TEST SIGNAL Pattern  
E
Off  
Caution: This selection replaces video.  
Pattern Field  
Default: Off  
Press the button until the cursor is at the Pattern label, and press ENTER to move into the field.  
4
Press the  
buttons to display the test patterns. Choose from the options listed below:  
  
NTSC/PAL M Test Pattern Options  
Color Bar  
IRE 100 Ramp  
NTSC 7 Comb  
Red Field  
NTSC 7 Comp  
5 Step Stair  
Unmod Y Ramp  
Off (Default)  
Test signals override any active service component, and the unit displays diagnostics over the  
video test patterns if diagnostics are enabled. For details, see "Menus Field" on page 75. To  
disable the selected video test signal, return to the Off setting or press ENTER to exit the field.  
DSR-6400 Series  
77  
     
3
Ad Insertion Test Menu  
Ad insertion signals are generated by the unit, but controlled by the uplink programmer. Local  
cable companies use ad insertion signals to control and to queue the insertion of commercials in  
cable headends. There are two ways to provide ad insertion. One is a dedicated digital DTMF  
differential output for cue tones. The other way is to use a dedicated contact closure relay. Use the  
Ad Insertion Test menu to turn on and off the cue tones and the relays.  
AD INSERTION TEST Cue Tone Relay  
E
Off  
Off  
CAUTION: During this test, live ad insertion may be interrupted. When turned on, the ad  
insertion signals can be sent to the local headed equipment.  
Press the  
buttons until the Ad Insertion Test menu appears.  
  
Cue Tone Field  
Default: Off  
Use this field to turn on and off the cue tone test. Press the button until the cursor is at the Cue Tone  
4
  
label, and press ENTER to move into the field. Press the  
buttons to display the two options: On  
and Off. If On is selected, the unit generates a DTMF code (0-9*#ABCD) on the cue tone output  
ports. This field returns to the default value (Off) when ENTER is pressed to exit the field.  
Relay Field  
Default: Off  
Use the Relay field to individually turn On and Off each of the ad insertion relays located on the unit’s  
back panel. Press the button until the cursor is at the Relay label and press ENTER to move into the  
4
field. Press the  
buttons to display the options. Depending on which DSR-6400-series model is  
  
being used, you will see one or more of the following options: Off, Relay1 On, Relay2 On, and Relay3  
On. This field returns to the default value (Off) when ENTER is pressed to exit the field. To add a  
Note: To review how the back panel cue tone and relay signal connections relate to the units  
processor paths and the processor fields (PR1, PR2, PR3, and PR4), see Figure 1-2 on page 16.  
78  
     
4
Product Support  
If You Need Help  
For assistance with your Motorola Mobility product, use one of the following channels:  
Technical Assistance Center (TAC) provides access to technicians 24 hours a day, 7 days a  
week for all products. Contact the TAC at 888-944-HELP (888-944-4357) or dial direct  
847-725-4011.  
Motorola Online (MOL), mobilityonline.motorola.com, provides technical documentation and  
low-priority issue creation and tracking. (PON and BSR users see Extranet Support below.)  
DigitalCM, digitalcm.motorola.com, provides software downloads and release updates.  
(PON users see Extranet Support below).  
Learning Portal, www.motorolatraining.com, provides self-paced product training and  
descriptions of instructor-led classes. In many cases, training can be given at your location.  
Extranet Support provides technical publications for PON (FTTx) users at  
compass.motorola.com/go/ftth and software downloads and technical publications for BSR  
users at bsr.motorola.com. For assistance with Motorola Mobility products only, contact the  
Motorola Mobility Technical Response Center (TRC), 24 hours a day, 7 days a week.  
DSR-6400 Series  
79  
     
4
Calling for Repairs  
If repair is necessary, call Motorola Mobility’s authorized repair vendor, World Wide Digital at  
1-800-227-0450 or 1-956-541-0600 for shipping address and a Return for Service Authorization  
(RSA) number before sending the unit for repair. The RSA number must be prominently  
displayed on all equipment cartons and shipping label. World Wide Digital is open from 8:00 AM  
to 5:00 PM Central Time, Monday through Friday.  
When shipping equipment for repair, follow these steps:  
1. Pack the unit securely.  
2. Enclose a note describing the exact problem.  
3. Enclose a copy of the invoice to verify the warranty status.  
4. Label all cartons and shipping labels with the RSA number.  
80  
 
5
Downlink/L-Band Frequency  
Conversion Tables  
A distributor or programmer can provide the latest L-band frequency plans at purchase time. Use the  
formulas in Table 5-1 and Table 5-2 to perform calculations for both C-band and Ku-band transponders,  
or for installing a new satellite.  
Table 5-1: Calculation for C-Band Transponders (Using 3,740 MHz Downlink Frequency)  
Example calculation if  
Formula for converting a C-band Frequency to an L-band Frequency  
downlink frequency is  
3,740 MHz  
5,150 MHz <minus> Frequency Downlink (DL) <equals> Frequency (L-band)  
5,150 MHz  
-3,740 MHz  
1,410 MHz  
Table 5-2: Calculation for Ku-Band Transponders (Using 12,019 MHz Downlink Frequency)  
Example calculation if  
Formula for converting a Ku-band Frequency to an L-band Frequency  
downlink frequency is  
12,019 MHz  
Frequency Downlink (DL) <minus> 10,750 MHz <equals> Frequency (L-band)  
12,019 MHz  
-10,750 MHz  
1,269 MHz  
DSR-6400 Series  
81  
     
6
Language Abbreviations  
This list of languages is recommended to system operators as the appropriate identifiers for audio,  
subtitle, and text information. Refer to Language Menu operation.  
Language  
Arabic  
Abbreviation  
Language  
Egyptian  
Abbreviation  
ara  
egy  
Armenian  
Balinese  
Basque  
arm  
ban  
baq  
btk  
ben  
bho  
bul  
bur  
cat  
chi  
English  
eng  
epo  
fao  
fin  
Esperanto  
Faroese  
Finnish  
Batak (Indonesian)  
Bengali  
French  
fre  
Bhojpuri  
Bulgarian  
Burmese  
Catalan  
German  
Greek  
ger  
gre  
guj  
heb  
hin  
hmo  
hun  
ind  
ina  
ira  
Gujarati  
Hebrew  
Chinese  
Croatian  
Cue (Tones)  
Czech  
Hindi  
scr  
cue  
cze  
dan  
dut  
iri  
Hiri Motu  
Hungarian  
Indonesian  
Interlingua  
Iranian  
Danish  
Dutch  
Irish  
Philippine (Other)  
phi  
DSR-6400 Series  
83  
 
6
Language  
Italian  
Abbreviation  
Language  
Polish  
Abbreviation  
ita  
pol  
Panjabi  
pan  
jpn  
Portuguese  
Rajasthani  
Romanian  
Russian  
Samoan  
Scots  
por  
raj  
Japanese  
Javanese  
Kashmiri  
Korean  
jav  
rum  
rus  
smo  
sco  
snd  
spa  
swa  
swe  
tgl  
kas  
kor  
kur  
lat  
Kurdish  
Latin  
Sindhi  
Malay  
may  
mdr  
mar  
mis  
mon  
nep  
nor  
oto  
pal  
Spanish  
Swahili  
Swedish  
Tagalog  
Tamil  
Mandar  
Marathi  
Miscellaneous  
Mongolian  
Nepali  
tam  
tha  
urd  
vie  
Thai  
Norwegian  
Otomian Lang.  
Pahlavi  
Urdu  
Vietnamese  
Welsh  
wel  
Persian  
per  
84  
7
Diagnostics  
Introduction  
The Fast Facts screens are used as a method of viewing information and diagnostic data associated  
with the unit. Information about these screens is described here for documentation purposes only.  
Notes:  
1. Hexadecimal numbers are displayed with none or more leading zeros (0) to pad to their  
individual field width.  
2. Decimal numbers are right-justified in their individual display rectangle and are not padded  
with leading zeros (0).  
3. Decimal numbers may be displayed with or without a trailing decimal point to distinguish them  
from hexadecimal numbers. The default is no trailing decimal point.  
DSR-6400 Series  
85  
     
7
Viewing the Fast Fact Diagnostic Screens  
The diagnostic screens (Figure 8-1) are available via the On-Screen Display (OSD) video out  
using a video monitor connected to the OSD Video Out port on the back of the unit.  
To view the OSD diagnostic screens, press the  buttons on the front of the unit until the  
Diagnostic menu appears, and press ENTER to access the Diagnostic menu on the unit.  
DIAG Menus  
Off  
PR  
E
1
Press the button to navigate to the Menus field and press ENTER to move into the field.  
4
DIAG  
Menus  
Clear Cntrs PR  
No  
E
Diag E  
1
Use the  buttons to choose one of the Fast Fact Diagnostic screens.  
Note: Pressing ENTER while viewing a particular OSD diagnostic screen allows for the  
continued display of the OSD diagnostic information while allowing the user to navigate thru  
other front-panel menus.  
Fast Facts 1 (General Information) [page 87]  
FF1  
Fast Facts 2 (RF Port Configuration) [page 89]  
FF2  
Fast Facts 3 (Video Information) [page 90]  
FF3  
Fast Facts 4 (Audio1 and 2 Information) [page 92]  
FF4  
Fast Facts 5 (10/100 Ethernet Port Information) [page 93]  
FF5  
FF5  
NOTE: To move  
between these two  
screens, use the  
Fast Facts 5 (GigE Port Information) [page 94]  
buttons.  
4  
Fast Facts 7 (Decoder Address) [page 95]  
Fast Facts 8 (Inbox) [page 96]  
FF7  
FF8  
FF9  
Fast Facts 9 (Archive) [page 97]  
Figure 8-1: Fast Fact Diagnostic Screens  
86  
   
Fast Facts 1  
The Fast Facts 1 screen displays general information relating to the basic functionality of the unit.  
Fast Facts 1 (PRX)  
Unit = 225-03177-05987-128  
VC # = 0132  
A
B
NOTE: The value after PR  
designates the processor that is  
currently specified within the  
menu system. For example,  
PR2 designates that Processor  
2 is specified. To view Fast  
Facts for another processor,  
change any PR field within the  
menu system to the desired  
processor number. The (PRX)  
designation does not appear on  
a DSR-6401.  
VCT ID = 0002  
D
Firmware = 000148 00017C  
C
Encryption = N/A  
E
Service # = 00003  
F
Eb/No = -2.0  
H
Auth State = Undefined Service  
G
Signal State = Searching  
Sat/Xpndr = T6/7  
I
J
Polarization = Horz  
L
Signal Quality = 58  
K
FEC Rate = 3/4  
Symbol Rate = 10.51 Msps  
N
M
Frequency = 1310.00 MHz  
Virtual Network = 7  
O
P
GigE IP = 000.000.000.000  
Q
Field  
Name  
Definition  
Unit  
Displays the 16-digit unit address on the screen.  
Displays the Virtual Channel number.  
A
VC#  
B
C
Firmware  
Displays the firmware version in the boot sector of ROM and the  
application section.  
VCT ID  
Displays the current VCT ID.  
D
Encryption  
Service  
Displays if the current service is encrypted or not.  
Displays the service number for the current program.  
E
F
Auth State  
If the current service is encrypted, this field displays the current  
authorization state of the IRD.  
G
Eb/No  
Shows the Signal to Noise (Eb/No) of the signal.  
H
I
Signal State  
Shows the received signal state. It can either be Locked or  
Searching, depending on whether the IRD is locked to a signal,  
or not.  
Sat/Xpndr  
Displays the satellite name and transponder number. If the  
satellite name is null, then the satellite number is used.  
J
DSR-6400 Series  
87  
 
7
Field  
Name  
Definition  
Signal Quality  
Displays the signal quality, if the signal is DigiCipher II.  
Otherwise, it displays the Signal Strength. Both values are nor-  
malized to be between 0 and 100%.  
K
Polarization  
Displays the polarization for the currently tuned-to transponder,  
either:  
L
Horz  
Vert  
Horizontal  
Vertical  
Symbol Rate  
FEC Rate  
Displays the current symbol rate.  
M
N
O
P
Displays the Forward Error correction (FEC) coding rate.  
Displays the current RF frequency.  
Frequency  
Virtual Network  
Displays the DSR-6400 Series’s currently tuned-in Virtual  
Network.  
GigE IP  
Displays the current GigE input IP address. If 000.000.000.000  
is displayed, the GigE input IP address is not actively receiving a  
transport stream through its GigE input port.  
Q
The GigE input IP address is displayed when the decoder is  
actively receiving a transport stream through its GigE input port.  
Otherwise 000.000.000.000 is displayed.  
88  
Fast Facts 2  
The Fast Facts 2 screen displays the DSR-6400 Series’s port configuration.  
Fast Facts 2  
Port 1 + G7(14) Vert ................. Defined  
Port 2 - ---(-) --- ................. Undefined  
Port 3 - ---(-) --- ................. Undefined  
Port 4 - ---(-) --- ................. Undefined  
Port 5 - ---(-) --- ................. Undefined  
Port 6 - ---(-) --- ................. Undefined  
Port 7 - ---(-) --- ................. Undefined  
Port 8 - ---(-) --- ................. Undefined  
A
B
C
D
E
Field  
Name  
Definition  
The port number being described (Port 1 through Port 8).  
Port Number  
Active Status  
A
+
-
Indicates the port is active.  
Indicates the port is inactive.  
B
C
D
Satellite Name  
Polarization  
The name of the current satellite. The Satellite ID is displayed  
within brackets.  
The polarity transponder associated with the port, either:  
Horz Horizontal  
Vert  
Vertical  
Configuration Status  
The configuration status of the port, either: Defined, Undefined,  
or Not Supported.  
E
DSR-6400 Series  
89  
 
7
Fast Facts 3  
The Fast Facts 3 screen displays information relating to video information.  
(PRX)  
A
C
E
G
I
B
D
F
H
J
NOTE: The value after PR  
designates the processor  
that is currently specified  
within the menu system. For  
example, PR2 designates  
that Processor 2 is specified.  
To view Fast Facts for  
another processor, change  
any PR field within the menu  
system to the desired pro-  
cessor number. The (PRX)  
designation does not appear  
on a DSR-6401.  
0x0000  
0x0000  
L
K
M
N
O
P
Field  
Name  
Definition  
Video Locked  
An indication of video lock status. Yes denotes the video for the unit is being  
received and locked. No denotes the video is not being received.  
A
Monitor  
Displays the current output format of the video display.  
Displays the current Program Identification (PID) number for the video.  
Displays the current dimensions of the video display:  
B
C
D
Video PID  
Window Dimensions  
Width x Height,  
Xpos : Ypos (or mute)  
PCR Pid  
Displays the current Program Clock Reference (PCR) PID.  
E
F
G
H
I
Aspect Mode  
Source Format  
Video Setup  
Resolution  
Displays the current aspect mode for the incoming video.  
Displays the source format: either Interlaced or Progressive.  
Displays the indication if the video setup (pedestal) is active, either Yes or No.  
Displays the Horizontal Size x Vertical Size of the received video.  
90  
 
Field  
Name  
Film Mode  
Definition  
Displays the indication of Film Mode activation. Either Yes (active) or  
No (inactive).  
J
Aspect Ratio  
Displays the aspect ratio of the video within the transport stream.  
K
L
Video Mute Count  
(VMC)  
Displays the current video mute count.  
Frame Rate  
Displays the frame rate code of the stream.  
M
N
PTS : FIFO  
Displays the video Presentation Time Stamp (PTS) followed by the Picture FIFO  
Depth Count.  
Chroma Ratio  
Video Rate  
Displays the Chrominance format for the video within the transport stream.  
O
P
Displays the rate (in Mbps) of the video within the transport stream.  
DSR-6400 Series  
91  
7
Fast Facts 4 (Audio 1 and 2)  
The Fast Facts 4 screen displays information relating to audio information. There are two columns of  
information displayed. The left column is for the first audio program, and the right column is for the sec-  
ond audio program.  
(PRX)  
NOTE: The value after PR desig-  
nates the processor that is cur-  
rently specified within the menu  
system. For example, PR2 desig-  
nates that Processor 2 is speci-  
fied. To view Fast Facts for  
another processor, change any  
PR field within the menu system  
to the desired processor number.  
The (PRX) designation does not  
appear on a DSR-6401.  
A
B
C
D
E
A
B
C
D
E
InputChans = [unlocked]  
F
InputChans = [unlocked]  
F
G
G
------  
H
H
Downmix = Unknown  
I
Downmix = Unknown  
I
Field  
Name  
Definition  
Audio Locked  
Displays the indication of audio lock status for both audio programs. If yes, then  
the audio for the unit is being received and locked. If No, then the audio is not  
being received.  
A
Audio Pid  
PCR Pid  
Displays the current Audio PID for both audio programs.  
Displays the current PCR PID for both audio programs.  
Displays the audio stream type: MPEG, AAC, AC3, etc.  
Displays the sampling rate (in kHz) of both audio programs.  
Displays the incoming audio mode of the active service.  
B
C
D
E
F
G
H
I
Type  
Sample Rate  
InputChans  
Language Preference Displays the preferred language setting for both audio programs.  
Language Status  
Downmix  
Displays the language status for both audio programs.  
Displays the audio processing type: Stereo, Surround, Mono (Mono output on  
left channel), or Dual Mono (Mono output on both left and right channels).  
92  
 
Fast Facts 5 (10/100 Network)  
The Fast Facts 5 screen displays information relating to the Ethernet port (left RJ-45 port on back of  
unit) configuration.  
Note: To move between the two Fast Fact 5 screens, use the  
buttons.  
4  
Fast Facts 5  
(10/100 Ethernet)  
Network Status = Link Up  
A
Address Type = Manually Configured  
B
MAC Address = 00:09:0E:CC:70:55  
C
IP Address = 010.077.005.066  
D
Subnet Mask = 255.255.254.000  
E
Gateway = 010.077.004.001  
F
Field  
Name  
Definition  
Network Status  
Displays connectivity status (either Link Up or Link Down).  
Displays address type.  
A
Address Type  
MAC Address  
IP Address  
B
C
D
E
F
Displays the MAC address of the unit.  
Displays the current IP address of the unit.  
Displays the current subnet mask of the unit.  
Displays the current gateway of the unit.  
Subnet Mask  
Gateway  
DSR-6400 Series  
93  
 
7
Fast Facts 5 (Gigabit Ethernet)  
The Fast Facts 5 (Gigabit Ethernet) screen displays information relating to Gigabit  
Ethernet port (right RJ-45 port on back of unit) configuration.  
Note: To move between the two Fast Fact 5 screens, use the  
buttons.  
4  
Fast Facts 5  
(Gigabit Network)  
Network Status = Link Down  
A
MAC Address = 00:09:0E:CC:70:55  
B
IP Address = 010.077.005.066  
C
Subnet Mask = 255.255.254.0  
D
Gateway = 010.077.004.201  
E
Output Mode = Disable  
F
Pass-Thru = 192.168.054.700: 6000  
G
Transcoded = 192.168.054.201: 6100  
H
Field  
Name  
Definition  
Network Status  
Displays the connectivity status (either Link Up or Link Down).  
Displays the MAC Address of the GigE port.  
Displays the IP address of the GigE port.  
A
MAC Address  
IP Address  
Subnet Mask  
Gateway  
B
C
D
E
F
Displays the Subnet Mask of the GigE port.  
Displays the Gateway of the GigE port.  
Output Mode  
Displays type of MPEG streams that are output from the GigE port. This could  
be off, pass-through, transcoded, or both pass-through and transcoded.  
Pass-Thru  
Displays the GigE IP address and port to where the pass-through MPEG stream  
is sent.  
G
H
Transcoded  
Displays the GigE IP address and port to where the transcoded MPEG stream  
is sent.  
94  
 
Fast Facts 7 (Decoder Address)  
The Fast Facts 7 screen displays the decoder’s address information.  
Fast Facts 7  
(Decoder Address)  
M16: 0112,7FFE,0F77  
A
M24: 00000A,00000B,00000C,00000D  
B
Field  
Name  
Definition  
Multicast Addresses  
The unit displays one to three16-bit multicast addresses as defined by the  
Uplink Provider. Each address is separated with a comma.  
A
Multicast Address(es)  
The unit displays from one to four 24-bit multicast addresses. Each address is  
separated with a comma.  
B
The DSR-6401 displays only one address, the DSR-6402 displays two  
addresses, the DSR-6403 displays three addresses, and the DSR-6404 dis-  
plays four addresses.  
.
DSR-6400 Series  
95  
 
7
Fast Facts 8 (Inbox)  
The Fast Facts 8 screen displays the unit’s current user-selected message from the list of all arrived mes-  
sages within the Inbox.  
Note: The unit will maintain up to  
Fast Facts 8  
(INBOX)  
300 mail messages between the  
Inbox mail messages (Fast Facts 8)  
and the Archived messages (Fast  
Facts 9). For example, when the  
267  
A
35  
B
st  
301 message arrives, the oldest  
1 812 2757094246  
message is then automatically  
C
D
E
purged. The unit, therefore, main-  
tains the most recent 300 mail mes-  
sages. Performing a factory reset  
will delete all messages from the  
decoder and reset the Message Drop  
G
1/04/2011 17:38:05: A code download is  
scheduled for 11/07/11 at 17:00. This  
will be the last download until we can  
look at future enhancements.  
F
Count field ( ) to 0.  
B
Field  
Name  
Definition  
Number of Inbox  
Messages  
Displays the number of messages (0 to 300) that are currently in the Inbox. For  
more details, see the above note.  
A
Message Drop  
Count  
Indicates the number of messages that were dropped due to a system overflow. A  
system overflow occurs when the 300-message maximum is exceeded, as  
described in the above note.  
B
If 0 appears in this field, no Inbox messages have been dropped since the most-  
recent factory reset. If 1 appears in this field, 301 messages have arrived since the  
most-recent factory reset and the oldest message was automatically purged. If 2  
appears in this field, 302 messages have arrived and the two oldest messages were  
automatically purged. Etc.  
Message Number Displays the message number that is currently being displayed from the Inbox. To  
display a different message, use the buttons to scroll through the messages.  
C
D
4  
If it is necessary to move the message to the archive and exit the message, press  
ENTER and ENTER again to confirm the move. To exit the message without mov-  
ing it to the archive, press ENTER and any arrow button (  
).  
4  
Message Page ID. This number is a running count of the mail messages that were  
sent from the BNC (uplink provider).  
Page ID  
CRC  
Message’s Cyclic Redundancy Check (CRC) value code.  
E
F
Received Time  
Displays the date and time at which this message was received at the decoder.  
The time is shown in GPS, as defined at the uplink. The time stamp is followed by  
a colon (:).  
Message Text  
Displays the text message.  
G
.
96  
   
Fast Facts 9 (Archive)  
The Fast Facts 9 screen displays the unit’s current user-selected message from the list of all messages within  
the Archive. Messages appear in this list after being moved here from the Inbox screen (Fast Facts 8).  
Fast Facts 9  
(ARCHIVE)  
35  
B
Note: The unit will maintain up to 300  
mail messages between the Inbox mail  
33  
A
messages (Fast Facts 8) and the Archived  
messages (Fast Facts 9). For example,  
st  
1 293 3371920703  
when the 301 message arrives, the oldest  
C
D
E
message is then automatically purged. The  
unit, therefore, maintains the most recent  
300 mail messages. Performing a factory  
reset will delete all messages from the  
decoder and reset the Message Drop  
G
12/27/2011 17:38:05: A blackout is  
scheduled for 11/01/11 at 15:00.  
F
Count field ( ) to 0.  
B
H 12/27/2011 21:19:35  
Field  
Name  
Definition  
Number of Archived Displays the number of messages (0 to 300) that are currently in the Archive. For  
A
Messages  
more details, see the above note.  
Message Drop  
Count  
Indicates the number of messages that were dropped due to a system overflow. A  
system overflow occurs when the 300-message maximum is exceeded, as  
described in the above note. If 0 appears in this field, no Archive messages have  
been dropped since the most-recent factory reset. If 1 appears in this field, 301  
messages have arrived since the most-recent factory reset and the oldest mes-  
sage was automatically purged. If 2 appears in this field, 302 messages have  
arrived and the two oldest messages were automatically purged. Etc.  
B
Message Number  
Displays the message number that is currently being displayed from the Archive.  
C
To display a different message, use the  
sages. If a 1 appears in this field, it designates the message was moved to the  
archive before all other archived messages. If this value is the same value as the  
buttons to scroll through the mes-  
4  
field for Number of Archived Messages ( ), it designates the message is the  
A
most-recently archived message.  
To exit the message, press ENTER.  
Page ID  
Message Page ID. This number is a running count of the mail messages that  
were sent from the BNC (uplink provider).  
D
CRC  
Message’s Cyclic Redundancy Check (CRC) value code.  
E
F
Received Time  
Displays the date and time at which this message was received at the decoder.  
The time is shown in GPS, as defined at the uplink.  
Message Text  
Archived Time  
Displays the text message.  
G
H
Display the date and time at which this message was moved to the Archive. The  
time is shown in GPS, as set up from the uplink.  
DSR-6400 Series  
97  
   
.
8
DSR-6400 Series Specifications  
RF  
Input Frequency Range  
950 to 2150 MHz  
-25 to -65 dBm  
75 Ohms  
Input RF Level  
RF Port Impedance  
RF Port Return Loss  
Port-to-Port Isolation  
12 dB minimum  
40 dB minimum  
Transmission Standard  
DVB-S2  
Symbol Rates:  
3 to 33 Msps  
8PSK Code Rates: 3/5, 2/3, 3/4, 5/6, 8/9, 9/10  
QPSK Code Rates: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10  
DigiCipher II  
Symbol Rates:  
3.25, 4.88, 7.32, 9.76, 11.7, 14.6,  
19.5, 29.7 Msps  
QPSK Code Rates: 5/11, 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 7/8  
Video  
Video Level  
1.0V p-p compliant with RS-250C  
Video Output Impedance  
Chrominance-luminance Delay Line  
Differential Gain  
75 Ohms  
±26 nsec  
4%  
Differential Phase  
1.5 degrees  
DSR-6400 Series  
99  
 
8
Audio  
Four channels  
Two pairs  
Peak Audio Level  
Analog Output Level  
Frequency Response  
Total Harmonic Distortion  
+20 dBm analog (0 dBFS)  
Adjustable over the range of 0/-20 dB in 1 dB steps  
+ 1 dB, 20 Hz to 20 KHz  
0.25% at 1 KHz  
Connectors  
RF In  
F-type connector (Qty 8)  
BNC connector (Qty 1)  
BNC connector (Qty 1)  
Terminal block (Qty 1)  
Terminal block (Qty 4)  
Terminal block (Qty 2)  
Terminal block (Qty 3)  
BNC connector (Qty 1)  
BNC connector (Qty 2)  
CF connector (Qty 1)  
Video Out  
OSD Video Out  
Alarm  
Cue Tone (Labeled: Q1/2/3/4+ and Q1/2/3/4-)  
Audio Out  
Contact Closure (Labeled: Relay 1, 2, and 3)  
ASI In  
ASI Out  
Compact Type 1 Flash  
TV Pass Card  
Ethernet 10/100  
Ethernet GigE  
TV Pass Card connector (Qty 1)  
RJ-45 connector (Qty 1)  
RJ-45 connector (Qty 1)  
Electrical  
DSR-6401  
100 to 240 VAC, 50/60Hz, 1.5A maximum, 341 Btu/hr  
100 to 240 VAC, 50/60Hz, 2A maximum, 512 Btu/hr  
100 to 240 VAC, 50/60Hz, 3A maximum, 853 Btu/hr  
100 to 240 VAC, 50/60Hz, 3.5A maximum, 1020 Btu/hr  
16 to 22 VDC, 450mA maximum  
DSR-6402  
DSR-6403  
DSR-6404  
LNB Power on RF Port 1  
100  
Mechanical  
Dimensions  
24.9x 19x 1.75”  
30x 21x 6.7”  
IRD without packing  
IRD with packing  
DSR-6401 Weight  
DSR-6402 Weight  
DSR-6403 Weight  
DSR-6404 Weight  
19.8 lbs. [9 kg maximum]  
16.3 lbs. [7.4 kg maximum]  
Finished goods with packaging and accessory)  
Finished goods without packaging  
20.85 lbs. [9.5 kg maximum]  
17.35 lbs. [7.9 kg maximum]  
Finished goods with packaging and accessory)  
Finished goods without packaging  
21.65 lbs. [9.8 kg maximum]  
18.15 lbs. [8.2 kg maximum]  
Finished goods with packaging and accessory)  
Finished goods without packaging  
22.36 lbs. [10.14 kg maximum] Finished goods with packaging and accessory)  
18.86 lbs. [8.6 kg maximum] Finished goods without packaging  
Special Instructions  
For restricted access locations, install the DSR-6400 Series only in restricted-access areas (dedicated equip-  
ment rooms, equipment closets, or the like) in accordance with Articles 110-26, 110-27, or the NEC ANSI/  
NFPA70, or per the applicable code in the country of installation.  
Always connect the protective earthing to one the two permanently-protective Earthing Terminals on the back  
panel of the DSR-6400 Series. For exact location, see Figure 2-1 on page 17.  
CAUTION: When connecting any of the eight RF IN ports, the RF-IN Antenna cable should only be  
connected while the DSR-6400 Series is properly grounded and the shield of the coaxial cable should be  
earthed in accordance with Article 820.93 of the NEC, ANSI/NFPA 70:2005, or equivalent.  
DSR-6400 Series  
101  
Recycling your Motorola Equipment  
Caring for the Environment by  
Recycling  
Please do not dispose of this product with your residential or  
commercial waste. Some countries or regions, such as the  
When you see this symbol on a Motorola product,  
European Union, have set up systems to collect and recycle  
do not dispose of the product with residential or  
electrical and electronic waste items. Contact your local authorities  
commercial waste.  
for information about practices established for your region. If  
For full details, see the following link:  
collection systems are not available, call Motorola Customer  
www.Motorola.com/recycling  
Service for assistance.  
Genbrug af dit Motorola-udstyr  
Beskyttelse af miljøet med genbrug  
Dette produkt må ikke bortskaffes sammen med husholdningsaffald eller erhvervsaffald. Nogle  
Når du ser dette symbol på et Motorola-produkt,  
må produktet ikke bortskaffes sammen med  
lande eller områder, f.eks. EU, har oprettet systemer til indsamling og genbrug af elektriske og  
elektroniske affaldsprodukter. Kontakt de lokale myndigheder for oplysninger om gældende  
husholdningsaffald eller erhvervsaffald.  
fremgangsmåder i dit område. Hvis der ikke findes tilgængelige indsamlingssystemer, kan du  
kontakte Motorola Kundeservice.  
Recycling bei Geräten von Motorola  
Umweltschutz durch Recycling  
Bitte entsorgen Sie dieses Produkt nicht als gewöhnlichen Haus- oder Büromüll. In einigen  
Wenn Sie dieses Zeichen auf einem Produkt von  
Motorola sehen, entsorgen Sie das Produkt bitte  
Ländern und Gebieten, z. B. in der Europäischen Union, wurden Systeme für die Rücknahme und  
Wiederverwertung von Elektroschrott eingeführt. Erkundigen Sie sich bitte bei Ihrer Stadt- oder  
nicht als gewöhnlichen Haus- oder Büromüll.  
Kreisverwaltung nach der geltenden Entsorgungspraxis. Falls bei Ihnen noch kein Abfuhr- oder  
Rücknahmesystem besteht, wenden Sie sich bitte an den Kundendienst von Motorola.  
Reciclaje de su equipo Motorola  
Cuidar el medio ambiente mediante  
el reciclaje  
No deseche este producto junto con sus residuos residenciales o comerciales. Algunos países o  
regiones, tales como la Unión Europea, han organizado sistemas para recoger y reciclar  
Cuando vea este símbolo en un producto  
desechos eléctricos y electrónicos. Comuníquese con las autoridades locales para obtener  
Motorola, no lo deseche junto con residuos  
información acerca de las prácticas vigentes en su región. Si no existen sistemas de recolección  
residenciales o comerciales.  
disponibles, solicite asistencia llamando el Servicio al Cliente de Motorola.  
Recyclage de votre équipement Motorola  
Recyclage pour le respect de  
l'environnement  
Veuillez ne pas jeter ce produit avec vos ordures ménagères ou vos rebuts d'entreprise. Certains  
pays ou certaines régions comme l'Union Européenne ont mis en place des systèmes de collecte  
Lorsque vous voyez ce symbole sur un produit  
et de recyclage des produits électriques et électroniques mis au rebut. Veuillez contacter vos  
Motorola, ne le jetez pas avec vos ordures  
autorités locales pour vous informer des pratiques instaurées dans votre region. Si aucun  
ménagères ou vos rebuts d'entreprise.  
système de collecte n'est disponible, veuillez appeler le Service clientèle de Motorola qui vous  
apportera son assistance.  
Uw Motorola-materiaal recycleren.  
Milieubewust recycleren  
Gooi dit product niet bij het huishoudelijk afval het of bedrijfsafval. In sommige landen of regio's  
Als u dit symbool op een Motorola-product ziet,  
zoals de Europese Unie, zijn er bepaalde systemen om elektrische of elektronische  
gooi het dan niet bij het huishoudelijk afval of het  
bedrijfsafval.  
afvalproducten in te zamelen en te recycleren. Neem contact op met de plaatselijke overheid  
voor informatie over de geldende regels in uw regio. Indien er geen systemen bestaan, neemt u  
contact op met de klantendienst van Motorola.  
Recykling posiadanego sprzĊtu Motorola  
DbaáoĞü o Ğrodowisko - recykling  
Produktu nie naleĪy wyrzucaü do komunalnych pojemników na Ğmieci. W niektórych krajach i  
Produktów Motorola oznaczonych tym symbolem  
regionach, np. w Unii Europejskiej, istnieją systemy zbierania i recyklingu sprzĊtu elektrycznego  
nie naleĪy wyrzucaü do komunalnych  
i elektronicznego. Informacje o utylizacji tego rodzaju odpadów naleĪy uzyskaü od wáadz  
pojemników na Ğmieci.  
lokalnych. JeĞli w danym regionie nie istnieją systemy zbierania odpadów elektrycznych i  
elektronicznych, informacje o utylizacji naleĪy uzyskaü od biura obsáugi klienta firmy Motorola  
(Motorola Customer Service).  
Reciclagem do seu equipamento Motorola  
Cuidando do meio ambiente  
através da reciclagem  
Não descarte este produto junto com o lixo residencial ou comercial. Alguns países ou regiões,  
tais como a União Européia, criaram sistemas para colecionar e reciclar produtos eletro-  
Quando você ver este símbolo em um produto  
eletrônicos. Para obter informações sobre as práticas estabelecidas para sua região, entre em  
Motorola, não descarte o produto junto com lixo  
contato com as autoridades locais. Se não houver sistemas de coleta disponíveis, entre em  
residencial ou comercial.  
contato com o Serviço ao Cliente da Motorola para obter assistência.  
PLEASE RECYCLE  
6450 Sequence Dr.  
San Diego, CA 92121  
Document No: 583611-001, Rev. B  

Radio Shack 10M User Manual
Planar Systems Car Video System PL2410W User Manual
Philips SA6015 User Manual
Panasonic DV PROLINE AG DVX100BAN User Manual
Mackie Car Speaker MR5 User Manual
Legacy Car Audio LA780 User Manual
Kenwood KDC 132 User Manual
JVC Picsio High Definition Digital Camcorder 0810YMH AL OT User Manual
JVC KD G830 User Manual
JVC GY HM700CHE User Manual