Marshall Electronics
1910 East Maple Ave.
El Segundo, CA 90245
Tel.: 800-800-6608 • 310-333-0606
Fax: 310-333-0688
Email: [email protected]
V-R231P-AFHD
Users Guide
External Dimension Drawing
Product Overview
Features
1
2
3
4
5
6
7
8
Electrical Specifications
Mechanical Specifications
Operational Setup
Connectors
8
Warranty
Marshall Electronics warranties to the first consumer, that this V-R231P-AFHD Advanced Function High Definintion 23-inch LCD monitor will, under normal use, be
free from defects in workmanship and materials, when received in its original container, for a period of one year from the purchase date.
This warranty is extended to the purchasing end user only and proof of purchase is necessary to honor the warranty. If there is no proof of purchase provided with
a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth above. Therefore, labor and parts may be charged to you.
This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifications in design or construction,
voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any warranties other than those described above, or to extend the
duration of any warranties on behalf of Marshall Electronics, beyond the time period described above.
Menu Functions
An extra note about LCD displays: It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the periphery of the display active viewing
area. Marshall Electronics has the option to reserve service for display pixel failure if deemed unobtrusive to effective use of the monitor by our technicians.
Due to constant effort to improve products and product features, specifications may change without notice. Due to constant effort to improve
products and product features, specifications may change without notice.
Warranty
Table 1 Computer Signals Displayed via DVI-I connector (VGA to DVI adapter may be required)
DVI-D
DVI-A
Input Signal Type and aspect
4x3
Y
16x9
Y
4x3
Y
16x9
Y
800 x 600 60Hz
1024 x 768 60Hz
Y
Y
Y
Y
Table 2 Video Signals Displayed via DVI-I and YPrPb connections (HDMI requires adapter to DVI)
Input Signal Type and aspect YPbPr DVI-D Input Signal Type and aspect YPbPr DVI-D
720 x 486 60i
Y
Y
Y
Y
Y
Y
Y
Y
N
N
Y
Y
Y
Y
N
N
1280 x720 25P
Y
N
N
Y
Y
Y
Y
Y
N
N
N
Y
Y
Y
Y
Y
720 x 576 50i
1280 x 720 24P
1280 x 720 23.98P
1920 x 1080 60i
1920x1080 59.94i
1920 x 1080 50i
1920 x 1080 30P
1920x1080 29.97P
720 x 486 60P
720 x 576 50P
1280 x 720 60P
1280 x 720 50P
1280 x 720 30P
1280 x720 29.97P
5
6
Operational Setup
1. Unpack the V-R231P-AFHD and accompanying V-PS24-7.5 power supply. Physically inspect for any damage that may have occurred
during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608. If you are not located within the
continental united states call +1 310-333-0606.
2. After inspection, install in your desired location. Marshall Electronics offers a desk top stand or rack mount kit for a standard EIA 19-inch
equipment rack. Adequate ventilation is required when installed to prevent possible damage to the V-R231P-AFHD internal components.
3. Connect required cables for signal input and output. Please note that power must be applied to the V-R231P-AFHD for all outputs to be
activated. All BNC connectors should be rated for 75Ω.
4. Attach XLR 4 pin power connection from V-PS24-7.5 power supply to the back of the unit.
5. Plug the V-PS24-7.5 power supply into the A.C. source
6.Turn on the V-R231P-AFHD by depressing the power switch located on the front of the unit.
Connectors
* HDSDI/SDI Inputs comply to SMPTE-259M, 292M, SDI-270Mbs, HDSDI-1.42 Gbs
* Component Inputs comply to SMPTE274M, 294M,295M,296M
Tally IN
DB-15 Female
* Composite Video Inputs comply to SMPTE-170M
* Tally lamps active when connected to ground
Pin1-Yel
Pin9-
Pin2-Red
Pin3-Grn
Pin4-
Pin5-Gnd
Pin6-
Pin10-
Pin11-
Pin12-
Pin13-
Pin14-
Pin15-Gnd
Pin7-
Pin8-
S-Video In
4 Pin Din (Female)
Pin1 - GND
Pin2 - GND
Pin3 - Yin
Pin4 - Cin
VESA 75mm
mount points
S-Video Out
4 Pin Din (Female)
Pin1 - GND
Pin2 - GND
Pin3 - Yout
Pin4 - Cout
Active Outputs require power to be applied
All input signals appear as output signal
Analog output signals are buffered and amplified
Power In
4 Pin Male XLR
Pin-1 GND
Pin-2 +24v
Marshall Electronics
3
DVI-I Connector
Pin#
Pin#
Signal
Signal
1
2
3
T.M.D.S DATA 2-
T.M.D.S DATA 2+
T.M.D.S DATA 2/4
SHIELD
16
17
18
HOT PLUG DETECT
T.M.D.S DATA 0-
T.M.D.S DATA 0+
VGA/XGA Connector
4
T.M.D.S DATA 4-
19
T.M.D.S DATA 0/5
SHIELD
T.M.D.S DATA 5-
T.M.D.S DATA 5+
T.M.D.S CLOCK
SHIELD
PIN#
SIGNAL
RED
PIN#
9
SIGNAL
NC
NC
NC
NC
HSYNC
VSYNC
NC
1
2
3
4
5
6
7
8
5
6
7
T.M.D.S DATA 4+
DDC CLOCK
DDC DATA
20
21
22
GREEN
BLUE
NC
GND
RED SHIELD
GREEN SHIELD
BLUE SHIELD
10
11
12
13
14
15
8
9
10
11
ANALOG VERT. SYNC
T.M.D.S DATA 1-
T.M.D.S DATA 1+
T.M.D.S DATA 1/3
SHIELD
T.M.D.S DATA 3-
T.M.D.S DATA 3+
+5V POWER
23
24
T.M.D.S CLOCK+
T.M.D.S CLOCK-
C1
ANALOG RED
12
13
14
15
C2
C3
C4
C5
ANALOG GREEN
ANALOG BLUE
ANALOG HORZ SYNC
ANALOG GROUND
GND
Menu Functions
7
1. Power On/Off Button with System Reset
Illuminates Red when system power is present. Illuminates Green when monitor is ON.
System reset will also occur with Off/On cycle. Active Outputs require power to be applied.
All input signals appear as output signal. Analog output signals are buffered and amplified.
2. Source Selection Buttons
HDSDI - Digital Input for Standard Definition (SDI-270Mbs) or High Definition (HDSDI-1.43Gbs)
Video - Composite NTSC or PAL. Composite video must comply to SMPTE-RS170A.
Images without color burst (Subcarrier) component may not display.
S-Video - Y/C (Luminance + Chrominance) NTSC or PAL
YPrPb - Analog Component color difference signals for Standard Definition (YCrCb) or High Definition (YPrPb)
VGA/DVI - Toggles between Analog PC or DVI-I connectors.
DVI - Digital or Analog Computer or Video Signals. Includes HDCP and can be used with HDMI originated signals via an adapter cable
3. Under Scan (Not Available for HD and PC Signals)
Displays scaled images without vertical and horizontal blanking applied. This function can only be used with Standard definition
signals. SDI signals will display all data input with ancillary data appearing to the right of the image.
4. Aspect Ratio
Displays scaled images in three screen aspect formats. 4:3 used mainly for Standard definition
16:9 used mainly for HDTV images.15:9 or Fill Mode is indicated by illuminating both LEDs. This mode will fill the entire
display screen regardless of the original screen aspect.
5. Pixel to Pixel Function
As the native LCD display of the V-R231P-AFHD is 1920 pixels wide by 1200 pixels high, it may be necessary to change the
size of the image to fill the screen in the desired aspect. Pixel to Pixel mode bypasses the enlargement/shrink of this scaling
function and displays the native incoming format.
For 525-NTSC/480P based images, pixel to pixel will appear as a 480h x 640w (4:3 aspect) or 480hx720w (16:9 aspect).
For 625-PAL/576P based images, pixel to pixel will appear as a 576h x 640w (4:3 aspect) or 576w x 720h (16:9 aspect).
For 1080 line HD based images, pixel to pixel will appear as 1080h x 1920w (16:9 aspect)
For 720 line HD based images, pixel to pixel will appear as a 720h x 1280w (16:9 aspect)
6. Color Temperature
The V-R231P-AFHD has four color temperature settings that adjust the color balance of the screen for varying ambient conditions.
D-55 (5500K) - Simulates indoor incandescent light conditions.
D-65 (6500K) - Standard setting recommended by SMPTE and EBU. Simulates normal daylight conditions.
D-75 (7500K) - Simulates bright daylight conditions.
User
When USER color temperature is selected, the color balance RGB Gain and Offset adjustments will be
enabled. Use UP/DOWN/LEFT/RIGHT (Safe, Mark, Frame, Overlay) to access the desired adjustment
parameter.
Left Line= Increase of Gain
Center Line = D65 (Default)
Right Line = Decrease of Gain
Right Line= Increase of Bias
Center Line = D65 (Default)
Left Line = Decrease of Bias
7. OSD
Use SELECT to enable the On Screen Display for input and function status.
Note that when turned off, a timeout of 8 seconds will pass before the display goes away.
SDI: 525i/60hz 4x3
8. BACKLIGHT Brightness
Holding OSD then tapping SAFE will toggle through 3 selections of backlight intensity.
High = 100% Backlight Brightness (approx. 250 cd/m2)
Med = 75% Backlight Brightness (approx. 188 cd/m2)
Low = 60% Backlight Brightness (approx. 140 cd/m2)
V-R231P-AFHD Users Guide
4
|