5. Source Menu (Use UP/ DOWN/ RIGHT buttons to select function)
Marshall Electronics
1910 East Maple Ave.
El Segundo, CA 90245
TV
S-Video Video PC
Analog RBG (PC)
9
9
9
9
9
9
9
9
9
9
9
9
9
Tel.: 800-800-6608 • Fax: 310-333-0688
Composite Video
S-VHS Video
T V
9
9
9
Email: [email protected]
Analog RGB – Select the on screen source display to be from the HD-15 PC connector on the rear of the unit. Audio speak-
ers will be from the red and white RCA connectors.
Composite Video – Select the on screen source display to be from the White RCA (Video) connector on the rear of the unit.
Audio speakers will be from the red and white RCA connectors.
S-VHS Video – Select the on screen source display to be from the White RCA (Video) connector on the rear of the unit.
Audio speakers will be from the red and white RCA connectors.
TV – Select the on screen display and speakers source input to be from the internal TV Tuner
3
The Quad Splitter
The quad splitter buttons, located on the left of the unit, are dual function buttons, the functions are indicated above and below each
button. The top four buttons are used to select the video channel, in the zoom mode and the setup mode, these buttons will be used to
navigate around the screen and will be explained later. The bottom four buttons are used to setup the quad splitter and also to use the
digital freeze, sequential switcher functions and setup menu. To access these functions it is necessary to press the ALT button along
with the desired function, ie. for the FREEZE function, press the ALT button and the FREEZE button together. The bottom row of but-
tons are used as follows:
Video Loss Detection: This unit is equipped with video loss detection. Should any signal get lost, the unit will automatically go into a
Quad-Splitter mode and "No Signal" will blink in the corresponding quadrant to indicate that a video signal has been lost.
ZOOM: Enters the 2X digital zoom mode at the single screen mode. Press once to zoom in, press again to zoom out. The zoom mode
is only available in the single screen mode and not in any of the multi-screen modes. In the zoom mode, a boundary will appear in the
center of the screen. The buttons with the arrows beneath them can now be used to move the boundary around the screen. To make the
boundary fill the entire screen, press the QUAD key, the arrow buttons can still be used to move the zoomed portion around the screen.
The zoom mode can be exited by pressing the ZOOM button again.
Picture-In-Picture, PIP: The PIP is a priority monitoring function. While the quad screen gives equal priority, or size to each channel, the
PIP gives one channel the full screen with the other three appearing in smaller boxes within the screen. The PIP boxes can be arranged
horizontally or vertically via the SETUP menu. To change the priority of the four channels, simply press the PIP button as needed.
Sequential Switcher, SEQN: The sequential switcher can be activated by pressing the ALT and SEQN buttons simultaneously. The
time delay for each channel can be set up in the SETUP menu. To skip a channel in the sequence, set the dwell to 0.
Quad-Splitter, QUAD: By pressing the QUAD button, the screen will show all four video inputs simultaneously. Each of the screens can
have a user designated ID which is done through the SETUP menu. To exit the quad function, press any of the 4 video channels. The unit
will also go into a quad mode when a video signal loss is detected and the quadrant will have "No Signal" signifying video loss detected.
Setup menu, MENU: The SETUP menu can be accessed by pressing ALT and MENU simultaneously. Any of the four sub-menus can be
chosen by pressing the corresponding ‘CH’ button, ie sub-menu 1 is accessed by pressing ‘CH 1’ button. When a sub-menu is selected,
the number in the [ ] will highlight and blink. The bottom of the screen will give any further instructions to navigate through this menu.
V-R154P Userrs Guide
15” Rackmountable LCD PANEL
with Quad-Splitter & Balanced Audio
4
Audio
For greater flexibility, the unit allows the user to manually select any video channel with any audio channel by simply selecting a video
source and then pressing any of the four audio channels desired. The inputs in the rear of the unit are XLR balanced audio at +4 dBu,
the input level meters reflect this reference setting and can only be changed at the factory. Any audio channel can be monitored by
pressing the corresponding ‘CH’ button on the right hand side of the unit. The VOLUME is adjusted using the VOLUME knob on the
front of the unit. The unit will also work in a MONO mode by pressing the MONO button. When the MONO function is active, the MONO
button will indicate this with a green LED. When HEADPHONES are plugged into the headphone jack, the speakers will be deactivated
and only the headphones will be active.
Installation
Menu Functions
The Quad Splitter
Audio
1
2
3
4
5
8
Warranty
Marshall Electronics warranties to the first consumer, that this V-R154P rackmount monitor will, under normal use, be free form defects in workman-
ship and materials, when received in its original container, for a period of one year from the purchase date.
This warranty is extended to the first consumer only and proof of purchase is necessary to honor the warranty. If there is no proof of purchase provided
with a warranty claim, Marshall Electronics reserves the right, not to honor the warranty set forth above. Therefore, labor and parts may be charged to you.
This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifications in design
or construction, voids this warranty.
Warranty
No sales personnel of the seller, nor any other person is authorized to make any warranties other than those described above, or to extend the dura-
tion of any warranties on behalf of Marshall Electronics, beyond the time period described above.
Due to constant effort to improve products and product features, specifications may change without notice.
11/30/2006
|