QS216
Thank you for choosing an MB Quart Q series component set for your car audio sound
system. With proper installation, you are on the path to experiencing your music in a
way you only imagined possible. Here at MB Quart, we call this “Sound In Every Detail.”
The Q series has been designed for those unique individuals who settle for nothing but
the best! Utilizing MB Quarts’ proprietary acoustic technologies and over 30 years of
experience developing and manufacturing speaker systems, the Q series makes the
emotions of music so perceptible that the passion of the musician is in perfect harmony
with the listener’s feelings.
QS216
QXO216 Crossover:
- Bi-Amplifiable: Tweeters can be powered separate from Midrange by removing jumpers and providing power
from independent channels.
- Tweeter Attenuation: Adjusts audible output of tweeter. Selectable settings of +1dB, 0 dB, -2dB and -4dB.
- Midrange Attenuation: Adjusts audible output of midrange. Selectable settings of 0dB, -3dB and -5dB.
TWEETER
BALANCED
TEMPERATURE
TECHNOLOGY
MID RANGE
WF + IN + TW WF - IN - TW
-
WF
+
-
TW
+
Removable Top
Input From Amp WF: Output to Midrange
TW: Output to Tweeter
x 2 per crossover
Jumpers:
QS216 SPECIFICATIONS
Included Components and Parts:
- Two QM216 6.5” (160mm) Woofers
- Two QTW216 1.575” (40mm) Tweeters
- Two QXO216 Crossover Networks
- Two Flush Mount Tweeter Fixtures
- Two Angle Mount Tweeter Fixtures
- Two Mesh Tweeter Grills
Woofers: 6.5” Nomex PMI Composite material designed
to be both light in weight and rigid. This
combination allows for a flat linear response
and incredible low frequency reproduction with
high sensitivty.
Tweeters: 40mm Teteron Silk Composite material that
- Two Mesh Woofer Grills
- Two ABS Grill Trays
allows for flawless reproduction of
frequencies found in silk tweeters and
improved durability from the Teteron blend.
Crossover
- Bag A:
- 8 pcs M4x32 Black Screws For Speakers
- 8 pcs Clips For Speakers
Networks: The High Definition Crossovers offer
advanced “Q Control” for the tweeter and
midrange with variable points of attenuation.
Featuring MB Quarts’ Balanced Temperature
Control Technology, your music will never
suffer through lengthy periods of high power
listening.
- 4 pcs M4x12 Black Screws For Crossover
- Bag B:
- 8 pcs Clips For Tweeters
- Bag C:
- 6 pcs Nickel Plated Screws For Tweeters
- 2 pcs Nickel Plated Flat Washers For Tweeters
- 2 pcs Nickel Plated Spring Washers For Tweeters
Continuous Power Handling: 80 watts
Maxx Music Power: 170 watts
Frequency Response: 35Hz - 32,000Hz
Efficiency Q 1W/1M: 89 dB
Nominal Impedance: 4 Ohms
QS216
We strongly recommend that you have your new Q
series speakers installed by your authorized MB
Quart dealer. The installation professionals
employed by your dealer have the necessary tools
and experience to disassemble your vehicle, install
your new speakers and reassemble everything
properly. If you prefer to perform your own
installation, it is very important that you read the
entire manual first.
STANDARD
Crossover #1:
1. Connect Amplifier Channel 1 + to Crossover
WF + IN.
2. Connect Amplifier Channel 1 - to Crossover
WF - IN.
3. Connect Crossover WF + and - output to the
corresponding + and - on midrange speaker #1.
4. Connect the Red tweeter wire to the output
TW + on the Crossover.
GETTING STARTED:
- Turn off the audio system.
- Check clearance on both sides of mounting
surface to ensure that there are no obstructions
(windows, tracks, wiring etc).
5. Connect the Black tweeter wire to the output
TW - on the Crossover.
Crossover #2:
1. Connect Amplifier Channel 2 + to Crossover
WF + IN.
2. Connect Amplifier Channel 2 - to Crossover
WF - IN.
3. Connect Crossover WF + and - output to the
corresponding + and - on midrange speaker #2.
4. Connect the Red tweeter wire to the output
TW + on the Crossover.
5. Connect the Black tweeter wire to the output
TW - on the Crossover.
Bi-Amp
Crossover #1:
1. Connect Amplifier Channel 1 + to Crossover
WF + IN.
CROSSOVER NETWORK INSTALLATION:
- Locate a dry location for mounting of your Q
Crossover Networks. DO NOT MOUNT IN
DOORS!
- Remove the cover of the crossover by squeezing
either side. This exposes the mounting holes for
securing the crossover to a flat surface. Prior to
pre-drilling pilot holes, ensure that you will not be
drilling into wiring, gas tanks, fuel lines etc.
- Once the crossover is mounted, snap the
protective cover back in place.
2. Connect Amplifier Channel 1 - to Crossover
WF - IN.
3. Connect Crossover WF + and - output to the
corresponding + and - on midrange speaker #1.
4. Connect Amplifier Channel 3 + to Crossover
TW + IN.
WIRING DIAGRAMS FOR STANDARD WIRING
AND BI-AMP WIRING
Standard Wiring Configuration: This wiring
configuration is used when you want to power
each crossover with a single amplifier channel. It
is important that you leave the jumper pins in
the locations shown in the diagram labeled
Standard.
5. Connect Amplifier Channel 3 - to Crossover
TW - IN.
4. Connect the Red tweeter wire to the output
TW + on the Crossover.
5. Connect the Black tweeter wire to the output
TW - on the Crossover.
Crossover #2:
Bi-Amp Wiring Configuration: This wiring
configuration is used when you want to power
each crossover with a pair of amplifiers(Bi-Amp) or
pair of channels (Bi-Wire). In this mode, the inputs
to the woofer’s low-pass filter and the tweeter’s
high-pass filter are electrically isolated. This
configuration is shown in the diagram labeled
Bi-Amp.
1. Connect Amplifier Channel 2 + to Crossover
WF + IN.
2. Connect Amplifier Channel 2 - to Crossover
WF - IN.
3. Connect Crossover WF + and - output to the
corresponding + and - on midrange speaker #2.
4. Connect Amplifier Channel 4 + to Crossover
TW + IN.
5. Connect Amplifier Channel 4 - to Crossover
TW - IN.
4. Connect the Red tweeter wire to the output
TW + on the Crossover.
5. Connect the Black tweeter wire to the output
TW - on the Crossover.
QS216
Standard Wiring Diagram
Jumpers
WF + IN + TW WF - IN - TW
-
WF
+
-
TW
+
CLIP INDICATOR
AMBER-
CLIP INDICATOR
AMBER-
GREEN-
PRE CLIP
OFT CLIP
RED-
ARD CLIP
GREEN-
PRE CLIP
SOFT CLIP
RED-
HARD CLIP
LEVEL
LEVEL
9V
0.2V
9V
0.2V
BASS BOOST
BASS BOOST
0dB
12dB
0dB
12dB
BASS FREQUENCY
MULTIPLIER
FREQUENCY
30Hz
80Hz
X15
X1
HIGH PASS
FILTER SLOPE
6dB
12dB
15Hz
1KHz
CHANNELS 1&2
HIGH PASS
CHANNELS 3&4
LOW PASS
(x1) 20Hz
(x15) 300Hz
300Hz
4.5KHz
40Hz
4.5KHz
CROSSOVER
CROSSOVER
LP-BP LP-BP HP-FULL
MONO STEREO
DUPE
(3&4)
HP-FULL
-
+
INPUT MODE
PROTECT
POWER
4CH
2CH
Bi-Amp Wiring Diagram
WF + IN + TW WF - IN - TW
-
WF
+
-
TW
+
WF + IN + TW WF - IN - TW
-
WF
+
-
TW
+
WF+/WF-
+TW/-TW
CLIP INDICATOR
AMBER-
CLIP INDICATOR
AMBER-
GREEN-
PRE CLIP
SOFT CLIP
RED-
HARD CLIP
GREEN-
PRE CLIP
SOFT CLIP
RED-
HARD CLIP
LEVEL
LEVEL
9V
0.2V
9V
0.2V
BASS BOOST
BASS BOOST
0dB
12dB
0dB
12dB
BASS FREQUENCY
MULTIPLIER
FREQUENCY
30Hz
80Hz
X15
X1
HIGH PASS
FILTER SLOPE
6dB
12dB
15Hz
1KHz
CHANNELS 1&2
HIGH PASS
CHANNELS 3&4
LOW PASS
(x1) 20Hz
(x15) 300Hz
300Hz
4.5KHz
40Hz
4.5KHz
CROSSOVER
CROSSOVER
LP-BP LP-BP HP-FULL
MONO STEREO
DUPE
(3&4)
HP-FULL
INPUT MODE
PROTECT
POWER
4CH
2CH
QS216
Tweeter Mounting Options
Flush Mount Method
Top Mounted Method
Mounting Surface
Mounting Brackets
Cup Mounting Screws
Mounting Bracket Washers
Mounting Bracket Screws
Mounting Surface
Surface Angle Mount Method
Cup Mounting Screws
Mounting Surface
Woofer Mounting Options
Mounting With ABS Gasket And Grill
4X
Mounting Without Grill
4X
4X
4X
QS216
Speaker, Tweeter and Crossover Placement Options:
Factory sound systems vary greatly. Some systems have coaxials (tweeter fixed in the center of the midrange) in the
door, while others have factory component (tweeter is separate from midrange) systems. If your system has the factory
component offering then you will want to locate your factory tweeter mounting location and compare it to the diagram
below. Some vehicles already have the tweeter in the ideal location, while others often position the tweeter in the top
corner of the door pane which is less than ideal. A good rule of thumb is to try and mount the tweeter within 8 inches
of the midrange woofer for optimal imaging and tonal balance. When selecting an optimal mounting location, ensure
that you are clear of any obstructions within the door. Cutting or drilling into moving parts or electrical accessory wires
can be very dangerous and costly.
Woofers should typically be installed in the factory locations. Simply ensure that the new woofer will not obstruct the
window or other moving parts in the door.
The Crossover should NEVER be mounted in the shell of the door. This can damage the crossover through vibration
and moisture which is NOT covered under warranty. The Crossover can be mounted in a kick panel, under a seat or in
the trunk as long as the area is not located near any moving parts in the vehicle which could cut or pull the wires
resulting in a short circuit.
All wiring to and from the crossover should avoid all moving parts in the vehicle which could potentially damage the
wiring. Take great care when running wires through the door frame and into the door as wires can easily be cut. A
rubber grommet should be used on both holes and wire loom should be wrapped around the exposed wires as shown
in the diagram below.
Alternate Tweeter
Location
Crossover
Ideal Tweeter
Location
Route speaker wires
through rubber grommet
between door jam and
door as shown. Use wire
Mid Bass
loom to protect the wires.
|