PRODUCT DESCRIPTION
The DXSR-1504 and DXSR-1508 are four and eight channel supervised digital receivers with solid state outputs designed
for use with Linear’s DX and DXS Format transmitters. These receivers can be used in a variety of security and remote
control applications. When the receiver detects a signal from a transmitter programmed into its memory, the appropriate
channel output activates. The channel outputs have three optional configurations; momentary, toggle on/off, and latch until
restored. Status and low battery outputs are for supervisory indications. Cutting jumpers select which channels require
supervisory status reports from transmitters.
DXSR-1504
DXSR-1508
Each unit incorporates a dual high-sensitivity superheterodyne diversity receiver with two whip antennas. This type of
receiver provides superior performance by preventing loss of signal due to multi-path interference.
SUPERVISED
In a typical installation, the receiver is connected to an alarm control panel, door strike, camera, high current relay or some
other devices. Transmitters are used to activate or control the devices. The receiver should be mounted indoors or inside
a weather resistant non-metallic housing for outdoor use.
DIGITAL RECEIVERS
The digital DX/DXS code format features over a million possible codes. The transmitters are precoded at the factory to
unique codes, so no field coding is required. For versatility, any transmitter can be programmed into any receiver channel.
Receivers must be programmed to recognize the transmitter’s code before system testing and operation. Up to 32
transmitters can be programmed into the receiver. Each button on multi-button portable transmitters send a unique code,
and are programmed as separate transmitters.
Installation Instructions
The CHANNEL display shows the channels activated and the presence of radio activity. Individual indicators for ALARM,
STATUS, and LOW BATT show the supervisory status of each receiver channel. All outputs can be configured for normally
open or normally closed.
The units can be powered from a 10.2-14.4 VDC or 12-16 VAC power source. The units will draw about 35 mA standby
and up to 120 mA in alarm.
(760) 438-7000 • FAX (760) 438-7043
USA & Canada (800) 421-1587 & (800) 392-0123
Toll Free FAX (800) 468-1340
FEATURES
COMPONENT LOCATIONS
STATUS
STATUS
INDICATORS
CHANNEL
DISPLAY
CHANNEL
DISPLAY
INDICATOR
LOW BATTERY
ALARM
INDICATOR
INDICATOR
RIGHT ANTENNA
TERMINAL
AUDIO TEST
POINT
LEFT ANTENNA
TERMINAL
OPEN CASE TO
VIEW COMPONENTS
GROUND
TEST POINT
OUTPUT POLARITY
JUMPER
RADIO ACTIVITY
INDICATOR
PROGRAM
JUMPER
CHANNEL
BUTTONS
OUTPUT
JUMPERS
CHANNEL BUTTON
ACCESS PANEL
TERMINAL
BLOCK
CASE LOCKING
SCREW
RECESSED WIRING
ACCESS HOLE
WIRING STRAIN
RELIEF POSTS
STATUS
JUMPERS
OPTION JUMPERS AND CHANNEL BUTTONS DETAIL
MOUNT RECEIVER
CHANNEL 3
MOUNT RECEIVER AS HIGH
CHANNEL 1
AS PRACTICAL USING
THE SCREWS AND SCREW
ANCHORS PROVIDED
CHANNEL 4
CHANNEL 2
STATUS
JUMPER
OUTPUT
JUMPER
CHANNEL 8
CHANNEL
BUTTON
CHANNEL 7
CHANNEL 6
DXSR-1508 ONLY
CHANNEL 5
CHANNEL BUTTONS ARE USED DURING PROGRAMMING AND
TO UNLATCH THE CHANNEL'S OUTPUT IN LATCHED MODE
OUTPUT JUMPERS SELECT MOMENTARY, TOGGLE, OR
LATCHED OUTPUT FOR EACH CHANNEL
WHEN A CHANNEL'S STATUS JUMPER IS CUT, THE CHANNEL
WILL REQUIRE STATUS TRANSMISSIONS FROM A SUPERVISED
TRANSMITTER PROGRAMMED INTO THAT CHANNEL
COVER THE SCREWS WITH THE
FOUR SCREW HOLE PLUGS PROVIDED
ATTACH ANTENNAS
CONNECT TERMINALS
MODEL DXSR-1508 ONLY
INSTALL THE TWO
ANTENNAS UNDER THE
LEFT AND RIGHT
ANTENNA TERMINALS
SECURE WIRES WITH ZIP-TIE
OUTPUTS TO DEVICE TO BE TRIGGERED
100 mA MAXIMUM PER OUTPUT
FROM POWER SOURCE
10.2-14.4 VDC OR 12-16 VAC
120 mA MINIMUM
TIGHTEN ANTENNA TERMINALS WITH
ANTENNA WHIPS BELOW THE SCREW
AND UNDER THE TERMINAL PLATE
AS SHOWN (BE SURE TOP COVER SLOTS
ALIGN WITH ANTENNAS)
WITH OUTPUT POLARITY JUMPER IN
PLACE, ALL OUTPUTS WILL SWITCH
TO GROUND WHEN ACTIVE
NOTE: SEE WIRING EXAMPLES ON
REVERSE SIDE OF THESE INSTRUCTIONS
|