Legacy Car Audio LSC7 User Manual

TFT-LCD MONITOR  
OWNER S MANUAL  
7 INCH COLOUR LCD MONITOR  
LSC7  
MD  
TIME AV
SEL  
+  
POWER  
REMOTE  
IND  
LS C7  
WWW.LEGACYCARAUDIO.COM  
4) LCD MONITOR OPERATING INSTRUCTION  
9)  
CONNECTOR  
Power Switch:  
push this switch to open the monitor, the indicate light turns on, the monitor begin to work,  
push again to turn off the monitor.  
Simulating measure increase:  
LSC7  
increase the picture brightness, color saturation, contrast, hue and volume total five contents,  
you can adjust the content associate with the key 3.  
Simulating Switch:  
according to personal favor you can adjust each simulating measure, press this button, to  
choose the simulating measure, press this button, it will display the content as the order:  
Brightness -color-saturation -Contrast-hue-volume. Decide which content that need to adjust.  
Press key or again to adjust this content. (It will be effective only for the hue adjustment in  
NTSC system)  
Simulating measure decrease:  
reduce the picture brightness, color saturation, contrast, hue and volume total five contents, you  
can adjust the content associate with the key 3.  
Video Input Option:  
used to choose the video signal sources. Usually, connect the video signal of VCD, DVD to Video,  
photographic head or other signal to video 2, use this switch to choose them.  
TIME:  
AV  
SEL  
+
MD  
TIME  
POWER  
REMOTE  
IND  
Mxa 2 hours 30-45-60-90-120 minutes selectable  
MODE:  
Press mode button to select 16:9 / 4:3 display  
Power Indicate Light  
Infrared receiving window: receive remote control instructions.  
TFT-LCD  
Connector: the power supply of the monitor and the input jack of video signal  
Video2 input  
CAR BACK REN  
LSC7  
10  
CAR AUDIO(DVD OR VCD)  
BATTERY  
AV  
SEL  
+
MD  
TIME  
POWER  
REMOTE  
IND  
2
9 8  
6
5
4
1
7
3
11  
2
5
5) Remote Control Operating Instruction:  
6) OPERATING METHOD  
Please acquaint the function of each key on the monitors and remote controller before using  
(Refer to the operating instruction of the remote controller and monitor operating instruction)  
When you adjust the brightness, colour saturation, contrast, hue and volume of the picture to  
the best mode, if you want to keep this mode when you open the machine each time, if the  
brightness you used now is different with last time, you can repeat operating way as above.  
(adjust again as the way in operating instruction.)  
1.Mute:  
If there is built-in speaker in the monitor, push this button to turn off sounds, push it again to  
turn on sounds.  
2.Stander-by:  
Because the monitors has built in video system auto-recognize circuit, the monitor can display  
the clear picture whether you input the NTSC video signal or PAL video signal.  
when the monitor is at work. Push this button, the MCU in the monitor will stop working with  
low power consumption, push this button again the monitor will recover to work normally.  
7) PRECAUTIONS  
5.AV transfer:  
This monitor adopt the DC power supply, so please distinguish the positive polarity and  
negative polarity of the power and use it within the regulated power supply (11V-14V), to  
avoid the damage of the monitor parts.  
use to switch the two way video and audio signal.  
6.Simulating measure increase:  
increase the picture brightness, color saturation , contrast , color hue and volume total 5 contents.  
You can adjust the content associate with the stimulating measure.  
TFT-LCD monitor is high exactitude parts, so please avoid the collide, shake violently and  
squeeze, do not use it below the temperature of 10  
the dampness, liquid, metal body etc. enter into the monitors. Avoid to cause  
the leaking of electricity and short circuit to damage to the LCD monitors.  
Do not operate the monitor when temperature below 15  
Since there is high-frequency power in the monitor please send it to professional or appointed  
maintenance service centre in case of malfunction It may cause danger of shock.  
or above the temperature of 40 . Avoid  
7.Simulating measure decrease:  
decrease the picture brightness, color saturation, contrast, color hue and volume total 5 contents,  
you can adjust the content associate with the stimulating measure  
8.Simulating choice:  
According to personal favor, you can adjust each simulating measure, push this button to choose  
the simulating measure, push this button, it will display the content as the order:  
Brightness-color-saturation -Contrast-hue-volume. Decide which content you need to adjust. Push  
key 6 or 7 again to adjust this content. (It will be effective only for the hue adjustment in NTSC  
system)  
8) ACCESSORIES  
1. Remote Controller 1 pcs  
2. Power and video input connecting wire 1 pcs  
3. User s manual 1 copy  
9.Volume decrease:  
if there is built-in speaker , in the monitor push the key  
to reduce the volume till no sounds.  
10.Volume increase:  
if there is built-in speaker, in the monitor, push the key to  
increase the volume,  
MD  
11.Colour Saturation Decrease:  
push the key to reduce the color saturation to colorless.  
L/R  
12.Colour Saturation Increase:  
push the key to increase the color saturation to maximum  
U/D  
gradually  
AV  
13.Contrast decrease:  
push the key to decrease the picture contrast gradually.  
SEL  
-
+
14.Contrast increase:  
push the key to increase the picture contrast gradually.  
TFT-LCD MONITOR REMOTE  
15.Brightness decrease:  
push the key to decrease the picture brightness gradually.  
16.Brightness increase:  
push the key to increase the picture brightness gradually.  
3
4

Raymarine Radar equipment Raychart Chartplotter RC530 PLUS User Manual
Prince Castle Cutters User Manual
Pioneer BONUS VIEW BDP 51FD User Manual
Panasonic Palmcorder PV GS39 User Manual
Panasonic Camcorder DMC SZ7 User Manual
Lochinvar KNIGHT 81 286 User Manual
Lochinvar EBN SUB 05 User Manual
K Tec HP3A User Manual
Kenwood MUSIC KEG FEATURES KCA R70FM User Manual
Kenwood KDV C810 User Manual