JVC HQ VHS User Manual

Dear Customer,

Thank you for purchasing the JVC Compact VHS camcorder. Before use, please read the safety informa-

tion and precautions contained in the following pages to ensure safe use of your new camcorder.

Using This Instruction Manual

•All major sections and subsections are listed in the Table Of Contents (੬ pg. 3).

•Notes appear after most subsections. Be sure to read these as well.

•Basic and advanced features/operation are separated for easier reference.

It is recommended that you . . .

..... refer to the Index (੬ pgs. 40 – 42) and familiarize yourself with button locations, etc. before use.

..... read thoroughly the Safety Precautions that follow and cautions (੬ pgs. 43, 44). They contain ex-

tremely important information regarding the safe use of your new camcorder.

SAFETY PRECAUTIONS

Warning on lithium battery

WARNING:

The battery used in this device may present a

TO PREVENT FIRE OR SHOCK

fire or chemical burn hazard if mistreated. Do

HAZARD, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE.

not recharge, disassemble, heat above 100°C or

incinerate.

Replace battery with Panasonic (Matsushita

Electric), Sanyo or Maxell CR2025; use of

another battery may present a risk of fire or

explosion.

CAUTIONS:

Ⅲ Dispose of used battery promptly.

Ⅲ Keep away from children.

Ⅲ Do not disassemble and do not dispose of in

fire.

Ⅲ To prevent shock, do not open the cabinet.

No user serviceable parts inside. Refer

servicing to qualified personnel.

Ⅲ When you are not using the AC Power

Adapter/Battery charger for a long period of

time, it is recommended that you disconnect

the power cord from AC outlet.

This camcorder is designed to be used with

PAL-type colour television signals. It cannot be

used for playback with a television of a different

standard. However, live recording is possible

anywhere. Use the BN-V12U/V22U/V25U

battery packs and, to recharge them, the

provided multi-voltage AC Power Adapter/

Charger. (An appropriate conversion adapter

may be necessary to accommodate different

designs of AC outlets in different countries.)

NOTES:

● The rating plate (serial number plate) and

safety caution are on the bottom and/or the

back of the main unit.

● The rating plate (serial number plate) of the

AC Power Adapter/Charger is on its bottom.

This unit is produced to comply with Standard

IEC Publ. 65.

PAL

Ⅲ Camcorder is designed exclusively for the VHS-C video cassette. Only cassettes marked VHS-C can be

used with this unit.

Ⅲ HQ VHS is compatible with existing VHS equipment.

GETTING STARTED

Power

CHG. (charge) indicator

Marks

This camcorder’s 3-way power supply system lets you

choose the most appropriate source of power.

POWER

indicator

To AC outlet

NOTES:

● No function is available without power supply.

● Use only specified power supply.

● Do not use provided power supply units with other

equipment.

END

indicator

CHARGING THE BATTERY PACK

SUPPLY POWER

Connect the charger’s AC power cord to a wall

outlet. The power indicator lights.

REFRESH switch

Charge marker

REFRESH indicator

ATTACH BATTERY PACK

Align the marks and slide the battery pack in the

direction of the arrow until it locks in place.

The CHG. indicator lights.

** CHARGE MARKER

A charge marker is provided on

the battery pack to help you

remember whether it has been

charged or not. Two colors are

provided (red and black)—you

choose which one means

charged and which means

discharged.

DETACH BATTERY PACK

When charging is completed, the END indicator

lights. Slide the battery pack opposite the direction

of the arrow.

BATT. PACK

CHARGE

DISCHARGE

BN-V12U

BN-V22U

BN-V25U

approx. 1 hr. 10 min.

approx. 3 hrs. 30 min.

approx. 2 hrs. 10 min. approx. 7 hrs.

approx. 2 hrs. 40 min. approx. 10 hrs.

USING THE BATTERY PACK

ATTACH BATTERY PACK

Hook on.

Hook its top end to the camcorder and push the

battery pack in until it locks in place.

DETACH BATTERY PACK

Slide BATT. RELEASE and pull out the battery pack.

Push in.

APPROXIMATE RECORDING TIME

BATT. PACK

GR-AX837

GR-AX637/AX337

1 hr. 10 min. (40 min.)

BATT. RELEASE

BN-V12U 1 hr. 10 min. (40 min.)

BN-V22U 2 hrs. 20 min. (1hr. 25 min.) 2 hrs. 25 min. (1hr. 30 min.)

BN-V25U 3 hrs. 5 min. (1hr. 55 min.) 3 hrs. 10 min. (1hr. 55 min.)

( ): when the video light is on (GR-AX837/AX637 only).

**REFRESH

ATTENTION:

The AC power adapter features a REFRESH function that

allows you to fully discharge the battery pack before

recharging.

Before detaching the power source, make

sure that the camcorder’s power is turned

off. Failure to do so can result in a

camcorder malfunction.

To discharge the battery . . .

..... attach the battery pack to the adapter as shown in the

illustration to the left. Then push REFRESH. The

REFRESH indicator lights when discharging starts,

and goes out when discharging is complete.

NOTES:

● The recording time per charge is affected by such factors as the time spent in Record/Standby mode and

the frequency of zooming. It is safer to have spare battery packs.

● Charging times noted on page 4 are for fully discharged battey pack, and discharging times are for fully

charged battery pack.

●

Charging and discharging times vary according to the ambient temperature and the status of the battery pack.

● Remember to set the charge marker after charging a battery pack or after detaching a discharged one from

your camcorder.

● Perform the REFRESH function after no less than 5 chargings.

● High temperatures can damage the battery pack, so use only where good ventilation is available. Don’t

allow it to discharge in container, such as a bag.

● If you stop recharging or discharging part way through, make sure to remove the battery pack before

unplugging the adapter’s AC cord.

● Remove the battery pack from the adapter immediately after discharging.

● To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.

● Make sure you unplug the DC cord before charging or discharging the battery pack.

●

A blinking CHG. indicator means that the battery pack has become hot. Wait until it cools down to continue.

● The CHG. indicator may not light properly with a brand new battery pack, or with one that’s been stored

for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHG.

indicator should light during recharging. If not, contact your nearest JVC dealer.

USING A CAR BATTERY

Use the optional Car Battery Cord or Car Battery

Charger/Adapter (connect as shown in the

illustration to the left).

To AC outlet

DC OUT

terminal

To DC

in jack

NOTES:

● When using the car battery, leave the engine

idling.

AC Power

Adapter/Charger

AA-V11EG

● The optional Car Battery Charger (BH-V3E) can

also be used to charge the battery pack.

● When using the optional Car Battery Charger or

Car Battery Cord (AP-V7E), refer to the respective

instruction booklet.

DC cord

To car’s

cigarette

lighter

USING AC POWER

Use the AC Power Adapter (connect as shown in

the illustration to the left).

socket

Car Battery Cord

AP-V7E (optional)

NOTE:

The supplied AC Power Adapter/Charger features

automatic voltage selection in the AC range from

110 V to 240 V.

Car Battery Charger/Adapter

BH-V3E (optional)

GETTING STARTED (cont.)

Clock (Lithium) Battery Insertion/Removal

This battery is necessary for clock operation and to

perform date/time settings.

SWITCH OFF POWER

Switch off the unit’s power and remove the power

supply unit.

OPEN COVER

Open the clock battery compartment cover while

pressing the release tab.

REMOVE BATTERY (when replacing)

Insert a pointed, non-metallic object between the

battery and the compartment ( ) and pull the

battery out.

INSERT BATTERY

Ensuring the plus (+) side is up, insert a CR2025

lithium battery and push it in.

CLOSE COVER

Close the compartment cover until it clicks in place.

NOTE:

See “SAFETY PRECAUTIONS” (੬ pg. 2) for information

on safe handling of lithium batteries.

Viewfinder Adjustment

POSITION VIEWFINDER

Adjust the viewfinder manually for best viewability

(see illustration at left).

SELECT MODE

Set the power switch to CAMERA.

ADJUST DIOPTER

Turn the diopter adjustment control until the

indications in the viewfinder are clearly focused.

Set POWER to “CAMERA”.

Date/Time Setting

SELECT MODE

First set the power switch to “CAMERA”. Turn the

PROGRAM AE select dial to any position except

AUTO LOCK.

ACCESS MENU SCREEN

Press MENU.

SELECT FUNCTION

Press – to move the highlight bar down to “DATE/

TIME”, then press NEAR. The Set Date And Time

screen appears.

–

PROGRAM AE

select dial

SET DATE/TIME

Press FAR or NEAR until the item you want to set

begins blinking, then press + or – to until the correct

setting appears.

NEAR

•If you decide you want to return the date and time

to the previous settings, press FAR or NEAR to

move the highlight bar to “CANCEL”, then press

MENU.

FAR

•If you’re satisfied with the settings, go on to step 5.

GAIN UP

TELE MACRO

S.LX

OFF

Menu Screen

START CLOCK OPERATION

INTERVAL TIMER OFF

REC TIME

OFF

Once you’ve set the day, month, year and time,

press FAR or NEAR until “SET” begins to blink, then

press MENU. The Menu screen reappears.

JLIP ID NO.

SET CHARACTER

DATE/TIME

CLOSE MENU

END :MENU KEY

Press MENU.

Set Time and

Date Screen

NOTES:

1.1.00

SET

10:45

● To display the date and time in the viewfinder and on a

connected TV, see “Date/Time Insert” (੬ pg. 20).

● If, in step 4, you input an invalid date (30. 2, 31. 6,

etc.) and perform step 5, “INPUT ERROR” appears

blinking at the bottom of the screen. Press +, –, FAR or

NEAR to input the correct number.

CANCEL

Date

Day/Month/Year

Time

24-hour indication

GETTING STARTED (cont.)

Tape Length Setting

SP-LP recording mode button

Set the tape length according to the length of the tape

used.

T30•45•60 tape

length select

button

SET TAPE LENGTH

Press T30•45•60 until the required indication

appears in the veiwfinder. T30 = 30 minutes of

recording time, T45 = 45 minutes, and T60 = 60

minutes (in SP).

NOTE:

The tape remaining time (੬ pg. 10) displayed in the

viewfinder is correct only if the correct tape length has

been selected.

Recording Mode Setting

Set depending on your preference.

SET RECORDING MODE

Set POWER to “CAMERA”.

Press SP-LP button. “SP” (Standard Play) provides

higher picture and sound quality and is better for

dubbing, while “LP” (Long Play) is more economi-

cal, recording at 1/2 the speed of SP.

Tape length indicator

T30

T45

T60

NOTE:

If the recording mode is switched during recording, the

playback picture will be blurred at the switching point.

Recording mode indicator

Loading/Unloading A Cassette

OPEN CASSETTE HOLDER

Slide EJECT until the holder opens. Do not use force

to open.

INSERT/REMOVE CASSETTE

Make sure the label is facing outward.

CLOSE CASSETTE HOLDER

Press PUSH and make sure the holder is closed and

locked.

NOTES:

● A cassette holder can’t be opened unless a power

supply is attached.

● Make sure that the tape is not slack when loading the

cassette. If there is any slack, turn the gear on the

cassette in the direction of the arrow to take up the

slack.

● Make sure the Erase Protection tab is in the position

that allows recording. If not, slide the tab. Some

cassettes have removable tabs. If the tab has been

removed, cover the hole with adhesive tape.

● The cassette holder can’t be opened while the

camcorder is in the record mode.

Turn to take

up slack.

Erase Protection

Gear

Grip Adjustment

EXPAND LOOP

Separate the Velcro strip.

INSERT HAND

Pass your right hand through the loop and grasp the

grip.

ADJUST STRAP LENGTH

Adjust so your thumb and fingers can easily operate

the Recording Start/Stop button and Power Zoom

lever. Refasten the Velcro strip.

Recording Start/Stop button

Shoulder Strap Attachment

ATTACH STRAP

Following the illustration at left, thread the strap

through the top of the eyelet 1, then fold it back

and thread it through the keeper 2, and then

through the buckle 3. Repeat the procedure to

attach the other end of the strap to the other eyelet,

making sure the strap isn’t twisted.

ADJUST LENGTH

Adjust as shown in the illustration at left 1, then

slide both keepers snug against the eyelets to

prevent slipping 2.

Tripod Mounting

ALIGN AND TIGHTEN

Align the screw and camera direction stud on the

tripod with the camera’s mounting socket and stud

hole. Then tighten the screw.

RECORDING Basic Recording

Tape remaining time indicator

NOTE:

You should already have performed the procedures listed

below. If not, do so before continuing.

● Power (੬ pg. 4)

25MIN

*---MIN

(Now calculating)

● Tape Length setting (੬ pg. 8)

● Recording mode setting (੬ pg. 8)

● Grip Adjustment (੬ pg. 9)

120MIN

119MIN

LOAD A CASSETTE

Power indicator

3MIN

Slide EJECT to open the cassette holder, then insert

the cassette with the label facing out. Press PUSH to

ensure the holder is closed and locked.

2MIN (Blinking)

1MIN (Blinking)

0MIN (Blinking)

ENTER RECORD–STANDBY MODE

Slide the LENS COVER open/close switch to open

the lens cover, then set the power switch to

“CAMERA”.

•The power indicator lights and the camcorder

enters the Record–Standby Mode.

•The scene you’re aimed at appears on the

viewfinder screen, with the word “PAUSE”

superimposed upon it.

LENS COVER

switch

START SHOOTING

Press the RECORDING START/STOP button.

POWER

•The tally lamp lights while recording is in progress,

and “^REC” appears in the viewfinder.

Start/Stop button

STOP RECORDING

Press the RECORDING START/STOP button again to

stop recording.

Tally lamp

•The camcorder re-enters the Record-Standby

mode.

NOTES:

● A cassette holder can’t be opened unless a power supply is attached.

● There may be a delay after you slide EJECT until the holder opens. Do not use force.

● The tape’s remaining time is displayed in the viewfinder as shown.

● The indicated remaining time is approximate.

● The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary

according to the type of tape used.

● The tape remaining time displayed in the viewfinder is correct only if the correct tape length has been

selected (੬ pg. 8).

● “TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this

condition for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is

loaded.

● If the Record–Standby mode continues for 5 minutes without performing Zoom or any other operations,

the camcorder’s power shuts off automatically. Set the Power switch to “POWER OFF”, and then back to

“CAMERA” to turn the camcorder on again.

● If the Recording Start/Stop button is pressed after the Record-Standby mode has continued for over 5

minutes, recording may not start immediately.

● If you’re recording on a cassette from the middle, use the RETAKE function (੬ pg. 12) to find the end of

the last recording so you don’t erase any of it.

● The LENS COVER warning blinks for about 10 seconds when the camcorder is turned on, when the cover

is closed.

RECORDING Basic Features

Power zoom lever

FEATURE:

PURPOSE:

Zooming

Varies the focal length of the lens

and produces the zoom in/out effect.

OPERATION:

Zoom In

1) Pull the power zoom switch down

toward “T”.

Zoom Out

1) Push the switch up toward “W”.

● The further the power zoom switch

is pushed, the faster the zoom

speed becomes.

NOTES:

● Focusing may become unstable

during zooming. In this case, set

the zoom while in Record–

Standby, set manual focus or Focus

Lock (੬ pgs. 16, 17), then zoom

in or out in Record mode.

Zoom-in

Zoom-out

Zoom indicator

RECORDING Basic Features (cont.)

FEATURE:

PURPOSE:

Quick Review

To check the end of the last record-

ing.

OPERATION:

1) Press “ ” and release quickly

during the Record–Standby mode.

•Tape is rewound for about 2

seconds and played back

automatically, then pauses in

Record–Standby mode for the

next shot.

RETAKE (R/F)

NOTE:

Distortion may occur at start of

playback. This is normal.

FEATURE:

Retake

PURPOSE:

OPERATION:

To re-record certain segments.

1) Make sure the camcorder is in the

Record–Standby mode.

2) Press either RETAKE button to

reach the start point for new

recording.

Pressing “F” fast-forwards the tape

and pressing “R” reverses it.

3) Press Recording Start/Stop to start

recording.

NOTE:

Noise may appear during Retake.

This is normal.

Video Light (GR-AX837/AX637 only)

When natural lighting is too dim, you can brighten the

scene by using the built-in video light.

SET VIDEO LIGHT

Set the LIGHT ON/AUTO/OFF as required.

1 _ON

: Always keeps the light on as long as the

camcorder is turned on.

AUTO : Automatically turns on the light when the

camcorder senses insufficient lighting on

the subject.

OFF : Turns off the light.

LIGHT ON/AUTO/OFF

•The video light can be used with the camcorder’s

power on.

•It is recommended to set the white balance

(੬ pg. 21) to indoor mode ( ) when you use the

video light.

•When not using the video light, turn it off to save

battery power.

NOTES:

● Even if the battery indicator (

) does not blink in the

viewfinder, if the battery pack’s charge is low, the

camcorder may turn off automatically when you turn

on the video light, or when you start recording with the

video light turned on.

● When the LIGHT ON/AUTO/OFF switch is set to

“AUTO”:

•Depending on the lighting conditions, the video light

may keep turning on and off. In this case, manually

switch the light on or off using the LIGHT ON/

AUTO/OFF switch.

•While the Sports or High-Speed Shutter mode

(੬ pg. 15) is engaged, the light is likely to stay on.

•While the Twilight mode (੬ pg. 15) is engaged, the

light will not activate.

DANGER

•The video light become extremely hot. Do not

touch it either while in operation or soon after

turning it off, otherwise serious injury may result.

•Do not place the camcorder into the carrying case

immediately after using the video light, since it

remains extremely hot.

•When operating, keep a distance of about 30 cm.

between the video light and people or objects.

•Do not use near flammable or explosive materials.

•It is recommended that you consult your nearest

JVC dealer for replacing the video light.

RECORDING Advanced Features

Programme AE With Special Effects

1 second later, the mode is activated.

All you have to do to access any of the variety of

shooting effects is to turn the PROGRAM AE select

dial.

After 1 sec.

SEPIA

SELECT MODE

Turn the PROGRAM AE select dial until the

symbol of the function you want is aligned

with the mark.

Viewfinder

•The selected mode’s name and its indication

are displayed in the viewfinder for approx.

1 second. Then the name disappears, and

only the indication remains. The mode is

activated.

•When Auto Mode Lock or Auto Mode

Release mode is selected, only the mode’s

name is displayed. Then the name disappears

and the mode is activated.

NOTES:

● Only one effect can be engaged at a time.

● The screen becomes slightly reddish when the

fader (੬ pg. 18) is used in the Sepia mode.

● The screen becomes slightly dark in the High

Speed Shutter mode. Use in well-lighted

situations.

● In the High Speed Shutter or Sports modes,

picture colour may be adversely affected if

subject is lit by alternating discharge-type light

sources such as flourescent or mercury-vapour

lights.

Mark

FAR NEAR

PROGRAM AE

select dial

–

DIAL

SYMBOL

VIEWFINDER

INDICATION

DIAL

SYMBOL

VIEWFINDER

INDICATION

MODE

FG:FOG

Electronic Fog Filter

LOCK

AUTO LOCK

Auto Mode Lock

Electronic Fog Filter

Locks the camcorder in Full Auto mode, preventing

incorrect operation due to accidental button

pressing during shooting.

Makes the picture look misty white, as when an

external fog filter is attached to the lens. Softens the

image and gives it a “fancy” look.

•In this mode the following controls are disabled;

FADE, WIDE, TITLE, DISPLAY, M.W.B (Manual

White Balance), Manual Focus, Focus Lock,

Exposure Control and MENU

ND:ND EFFECT ND Effect

ND Effect

A black mist darkens the picture, as when an ND

filter is used. Helps to counter the effects of glare on

the subject.

RELEASE AUTO RELEASE Auto Mode Release

Auto Mode Release

Re-enables the controls that were disabled by Auto

Mode Lock.

DIAL

SYMBOL

VIEWFINDER

INDICATION

DIAL

SYMBOL

VIEWFINDER

INDICATION

MODE

SEPIA

Sepia

SPORTS

Sports

Sepia

Sports

The scene being shot is recorded in sepia-tinted

(reddish-brown) monochrome, giving the effect of

an older movie. Use together with Wide (੬ pg. 18)

for the authentic look of a classic Hollywood

movie.

High shutter speed clearly captures fast-moving

action.

1/1000 sec.

1/1000

1/2000

S 1/1000

S 1/2000

High Speed Shutter

1/2000 sec.

TWILIGHT Twilight

High Speed Shutter

Twilight

High-Speed Shutter (1/1000s., 1/2000s.)

Captures faster action than Sports mode.

Dusk, twilight scenery, fireworks, etc., look more

natural and dramatic. The following happens when

Twilight mode is selected:

•Auto gain control is turned off.

•White Balance is set to “ ” (outdoor mode), but

can also be manually changed to another mode

(੬ pg. 21).

•Auto Focus becomes available only in the range of

10 m to infinity. To focus when the subject-to-

camera distance is less than 10 m, use manual

focusing (੬ pg. 17).

Exposure Control

This feature automatically adjusts the iris for the

best available picture quality, but you can override

and make the adjustment manually.

SELECT MODE

Turn the PROGRAM AE select dial to any

position except AUTO LOCK.

BRIGHTEN IMAGE

Press + (maximum +06). The Exposure level

indicator appears in the viewfinder.

OR . . .

DARKEN IMAGE

Exposure Level Indicator

Press – (maximum –06). The Exposure level

–

indicator appears in the viewfinder.

When you want to return to the factory

setting . . .

To brighten the image

RESTORE INITIAL SETTING

Press + and – simultaneously. The standard

setting is immediately restored and the

Exposure level indicator disappears.

–

To darken the image

RECORDING Advanced Features (cont.)

Focusing

Auto Focus

The camcorder’s Full Range AF system offers continuous

shooting ability from close-up to infinity. However,

correct focus may not be obtainable in the situations

listed below (in these cases use manual focusing):

Focus

detection zone

•When two subjects overlap in the same scene.

•When illumination is low.*

•When the subject has no contrast (difference in

brightness and darkness), such as a flat, one-colour

wall, or a clear, blue sky.*

•When a dark object is barely visible in the viewfinder.*

•When the scene contains minute patterns or identical

patterns that are regularly repeated.

•When the scene is affected by sunbeams or light

reflecting off the surface of a body of water.

•When shooting a scene with a high-contrast

background.

* The low-contrast warning “

viewfinder.

” appears in the

Focus Lock

This feature locks the focus in place, which is especially

helpful in the following situations:

FAR

NEAR

•When things pass between your subject and the

camcorder. Engage the focus lock function to lock your

subject in before recording.

•When you want your subject to be focused, and to

appear in a corner of the screen. First, center on the

subject and focus using auto focus mode. Then engage

the focus lock function and move the camcorder until

the subject is where you want it.

PROGRAM AE select dial

SELECT MODE

Turn the PROGRAM AE select dial to any position

except AUTO LOCK.

LOCK FOCUS

Press FAR or NEAR. The focus lock indication “

”

appears in the viewfinder.

RELEASE FOCUS LOCK

Press FAR and NEAR simultaneously. The focus lock

indication disappears.

NOTES:

● If the lens is smeared or blurred, accurate focusing is

not possible. Keep the lens clean, wiping with a piece

of soft cloth if it gets dirty. When condensation occurs,

wipe with a soft cloth or wait for it to dry naturally.

● When shooting a subject close to the lens, zoom-out

first (੬ pg. 11). If zoomed-in in the auto focus mode,

the camcorder could automatically zoom out

depending on the distance between the camcorder and

the subject. *When Tele Macro (੬ pg. 23) is activated,

the camcorder will not zoom out automatically.

Manual Focus

Power zoom lever

NOTE:

You should already have made the necessary viewfinder

adjustments (੬ pg. 6). If you haven’t, do so before

continuing.

SELECT MODE

Turn the PROGRAM AE select dial to any position

except AUTO LOCK.

ADJUST FOCUS

To farther subject . . .

Press and hold FAR. The Manual Focus indications

“

” appear and “ ” blinks.

Go to step 3.

FAR

NEAR

To nearer subject . . .

Press and hold NEAR. The Manual Focus indications

“

” appear and “ ” blinks.

Go to step 3.

PROGRAM AE select dial

LOCK FOCUS

Release FAR or NEAR. The focus indication is

replaced by the focus lock indication “

adjusted focus is locked in.

” and the

RELEASE MANUAL FOCUS MODE

Press FAR and NEAR simultaneously. The Manual

Focus mode is immediately released and the focus

lock indication disappears.

NOTES:

● Be sure to focus the lens in the maximum telephoto

position when you use the Manual Focus mode. If you

focus in on a certain subject in the wide-angle position,

sharply focused images cannot be obtained when

zoomed up because the depth-of-field is reduced at

longer focal lengths.

● When the focus level cannot be adjusted any farther or

closer, “ ” or “ ” will blink.

RECORDING Advanced Features (cont.)

Fader

Function indication

This feature allows smooth fade-in and fade-out to black

blank screen. Fade-in works at recording start, and

fade-out works at recording end or when you enter

Record–Standby mode.

FADE

Fade-Standby

indication

SELECT MODE

SELECT button

Turn the PROGRAM AE select dial to any position

except AUTO LOCK.

SELECT FUNCTION

FADE

Press SELECT repeatedly until “

” appears.

ENGAGE FADE–STANDBY MODE

Press SET to engage the Fade–Standby mode.

The Fade-Standby indication “FADE” is displayed.

START RECORDING

Press Recording Start/Stop to start recording and

activate fade-in.

PROGRAM AE select dial

SET button

OR . . .

END RECORDING

Press Recording Start/Stop to end recording and

engage fade-out.

FADE IN

NOTES:

● Pressing and holding the Recording Start/Stop button

allows you to record a black blank screen.

● The screen becomes slightly reddish when the Fader is

used with Sepia (੬ pg. 15).

● With the Electronic fog filter mode (੬ pg. 14)

engaged, the image fades in/out to a white screen.

FADE OUT

Wide

This feature allows you to record black bars at the top

and bottom of the screen to produce a cinema-like

“wide-screen” effect.

Wide mode

SELECT MODE

Turn the PROGRAM AE select dial to any position

except AUTO LOCK.

SELECT FUNCTION

Press SELECT repeatedly until “ WIDE ” appears.

ENGAGE WIDE MODE

PressSET.

RESTORE NORMAL SCREEN

WIDE

Press SET again while “

” appears.

Instant Titles

Title indication

TITLE

The camcorder has eight preset titles in memory. You can

superimpose one of them above a previously stored title as

shown in the illustration to the left.

HAPPY BIRTHDAY

HAPPY HOLIDAYS

OUR FAMILY

DISPLAY

SELECT MODE

MOVIE STAR

Turn the PROGRAM AE select dial to any position

PARTY TIME

except AUTO LOCK.

No indication

MERRY CHRISTMAS

WEDDING DAY

CONGRATULATIONS

SELECT FUNCTION

Press SELECT repeatedly until “ TITLE ” appears.

SELECT

SET

SELECT PRESET TITLE

The characters you

have set using

Character Generator

Engage the Record–Standby mode, then press SET to

cycle through the preset titles until the desired title is

displayed.

NOTES:

● To delete the Instant Title during recording, press SET.

● To recall a title, engage the Record–Standby mode and then

press SET to select the desired title.

PROGRAM AE

select dial

Character Generator

You can enter an original title of up to 18 characters.

ACCESS MENU SCREEN

except AUTO LOCK, then press MENU.

GAIN UP

S.LX

OFF

Turn the PROGRAM AE select dial to any position

TELE MACRO

INTERVAL TIMER OFF

REC TIME

OFF

ACCESS CHARACTER SET MENU

JLIP ID NO.

Press + or – to move the highlight bar to “SET

SET CHARACTER

DATE/TIME

CHARACTER”, then press NEAR. The Character Set

menu appears.

END :MENU KEY

INPUT CHARACTERS

Press +, –, FAR or NEAR to move the pointer to the

desired character, then press MENU. The selected

characters appear at the bottom of the screen. Repeat as

many times as desired (max. 18).

SET : MENU KEY

•To select the location of the next character, press +, –,

FAR or NEAR to highlight the row of squares at the

bottom of the screen, then press FAR or NEAR to

make the desired location blink. Press + when you’re

done, and the pointer returns to the character grid.

V W X

ࡖ

’

Ñ Æ Ø

–

0 1 2 3 4 5 6 7 8

L I

END CHARACTER SETTING

press MENU twice to return to the normal screen.

END

CLEAR

Press +, –, FAR or NEAR to make “END” blink, then

SET : MENU KEY

NOTES:

● To erase a character you entered mistakenly, make “CLEAR”

blink by pressing +, –, FAR or NEAR, then press MENU. All

characters are deleted at once. Or, to erase selected characters

only, first move the pointer to the row of squares by pressing +,

–, FAR or NEAR to highlight them. Press FAR or NEAR to make

the desired character blink, then press +, FAR or NEAR to move

the pointer to “ ” in the top left corner. Press MENU.

● To display the characters you have set — “Instant Titles” or

“Date/Time/Character Insert” (੬ pg. 20).

V W X

ࡖ

’

Ñ Æ Ø

–

0 1 2 3 4 5 6 7 8

L I KE YOU

ࡖ

END

CLEAR

● Characters may be set only in the Record-Standby mode.

RECORDING Advanced Features (cont.)

Date/Time Character Insert

SELECT

This feature allows you to display date, time and characters

in your viewfinder and on a connected colour monitor,

record them manually or automatically, and even make

your own titles.

NOTE:

You should already have performed the Date/Time

Setting procedure (੬ pg. 7). If you haven’t, do so before

continuing.

DISPLAY

SET

SELECT MODE

Turn the PROGRAM AE select dial to any position

PROGRAM AE

select dial

DISP.

except AUTO LOCK.

SELECT DISPLAY

DISP.

Press SELECT repeatedly until “

” appears.

Auto Date Record mode

Date-off mode

Date display

CHOOSE DISPLAY MODE

Press SET while in Record–Standby to cycle through

the modes as shown in the illustration at left.

Character Generator

Date/Time display

NOTES:

● The selected display can be recorded.

● If you don’t want to record the display, select Date-off

mode before shooting.

Auto Date Record mode

● If you want to delete the display during shooting, press

SET.

● If you want to call back a deleted display, engage the

Record–Standby mode and then select the desired

display mode using SET.

AUTO DATE

25.12.97

Auto date record

mode

Auto date record

executed

AUTO DATE RECORD

Your camcorder automatically records the date for about

5 seconds after recording is initiated in the following

situations:

•After changing the date.

•After loading a cassette.

Date display

Date/Time display

•After Auto Date Record mode is selected by pressing

SE T.

25.12.97

10:45

In this mode, the date is replaced after 5 seconds with

“AUTO DATE”.

Character Generator

NOTES:

● Setting PROGRAM AE to LOCK always engages this

mode, and disables all other modes.

● In the Auto Date Record mode, if the date changes

while you’re shooting, the date indication is recorded for

about 5 seconds from that point. It is not recorded

during any other recordings made on that day.

SET CHAR

IN PARIS, FRANCE

No Characters

stored

Example of stored

characters

Manual White Balance Adjustment (M.W.B.)

SELECT

This camcorder’s Automatic Colour Temperature system

senses the colour temperature of the ambient lighting for

automatic white balance adjustment. However, precise

colour adjustment is not possible under the following

conditions:

• When an object is in various shades of the same colour.

• When a predominantly red or brown object is being shot

outdoors.

In these cases, use the camcorder’s built-in preset filters for white

balance adjustment.

SELECT MODE

SET

Turn the PROGRAM AE select dial to any position

PROGRAM AE select dial

except AUTO LOCK.

SELECT FUNCTION

M.W.B.

White balance

mode indicator

M.W.B.

Press SELECT reapeatedly until “

” appears.

MWB

SELECT WHITE BALANCE

Press SET (Manual White Balance) until the

required indication appears in the viewfinder.

No indication (Auto)

MWB

“MWB” ..... With a memorized personal White Balance

setting (see below)

“

” ......... Outdoors on sunny day

”......... Outdoors on cloudy day

” .......... Light source is halogen or tungsten lamp

MWB

MWB sets the colour temperature for the subject’s light

source so you can shoot with natural colours that are

unaffected by surroundings, even when there are multiple

subjects with different colour temperatures.

SELECT MODE

Turn the PROGRAM AE select dial to any position

except AUTO LOCK.

ADJUST FOCUS

Point the camcorder at a white, flat object such as a

sheet of white paper, and adjust focus manually

(੬ pg. 17).

ADJUST WHITE BALANCE

Press SET until “MWB” appears, then press and hold

SET for more than 3 seconds.

• “MWB” blinks in the viewfinder during adjustment, then

stops blinking but stays lit when adjustment is complete.

NOTES:

● To switch to automatic white balance adjustment, press SET until the indication disappears, or turn the PROGRAM AE

select dial to “AUTO LOCK”.

● Re-adjust the White Balance when the lighting has changed, when the camcorder has been turned on and off again, or

when the PROGRAM AE select dial’s position has been changed.

● It is helpful to connect your camcorder to a colour monitor when adjusting the white balance (“Basic Connections”

੬ pg. 27).

● When adjusted by putting coloured paper in front of the subject in step 2 (“ADJUST FOCUS”), this unit makes its colour

temperature standard for automatic white balance. So you can enjoy shooting with different colours. For example, when

adjusting with red, blue or yellow colours, the image becomes the colour which aproximates to green, orange or purple

respectively.

RECORDING Advanced Features (cont.)

Using Menu For Detailed Adjustment

This camcorder is equipped with Program Manager, an

easy-to-use, on-screen menu system that simplifies many

of the more detailed camcorder settings.

SELECT MODE

Turn the PROGRAM AE select dial to any position

except AUTO LOCK.

ACCESS MENU SCREEN

Press MENU.

SELECT FUNCTION

FAR

Press + or – to place the highlight bar on the desired

function.

NEAR

–

MAKE SETTING

The setting procedure depends on the function you

select.

GAIN UP

TELE MACRO

INTERVAL TIMER OFF

S.LX

OFF

If you select GAIN UP, TELE MACRO, INTERVAL

TIMER, REC TIME or JLIP ID NO. . . .

.... press FAR or NEAR to cycle through the choices

until the desired setting appears.

If you select SET CHARACTER or DATE/TIME, . . .

.... press NEAR to access the selection menu for

each function (SET CHARACTER – ੬ pg. 19;

DATE/TIME – ੬ pg. 7).

REC TIME

OFF

JLIP ID NO.

SET CHARACTER

DATE/TIME

END :MENU KEY

CLOSE MENU

Press MENU. The normal screen reappears.

GAIN UP

NORM

TELE MACRO

INTERVAL TIMER 1MIN

REC TIME

1/2S

JLIP ID NO.

NOTE:

SET CHARACTER

DATE/TIME

The menu is available only in the Record-Standby mode.

END :MENU KEY

PAUSE

If GAIN UP or TELE MACRO in the Menu has

been changed from the factory settings, this

mark appears in the viewfinder.

GAIN UP

S.LX

To record a subject in a dark lit environment. When it is more

convenient to shoot the subject with a brighter image even if

the picture becomes slightly coarse. Automatically selected

when the PROGRAM AE select dial is set to AUTO LOCK

mode. (S.LX : Super LoLux)

NORM

OFF

To record a subject in a dimly lit environment. When it is

more convenient to shoot with a less coarse picture although

the subject becomes slightly dark.

Allows you to shoot dark scenes with no picture brightness

adjustment.

TELE MACRO

OFF

Usually set to this position.

Usually the distance to a subject where the lens is in focus

depends on the zoom magnification. Unless there is a

distance more than 1m to the subject, the lens is out of focus

at the maximum telephoto setting. When set to “ON”, you

can shoot a subject as large as possible at a distance of

approx. 60 cm.

•Depending on the zoom position, the lens may go out of

focus.

OFF

15 S

INTERVAL TIMER

This feature allows you to set the parameters for Self-Timer

(੬ pg. 24) and Time-Lapse recording (੬ pg. 25).

30 S

1 MIN

5 MIN

OFF

1/4 S

1/2 S

1 S

REC TIME

This feature allows you to set the parameters for Animation

and Time-Lapse recording (੬ pg. 25).

JLIP ID NO.

This number is necessary when connecting the camcorder to a device such

as a computer using the J terminal (JLIP).

The numbers range from 01 to 99. Factory setting is 07.

SET CHARACTER

DATE/TIME

Allows you to input characters. (੬ pg. 19).

Allows you to set the current date and time (੬ pg. 7).

= Factory setting and when the PROGRAM AE Select Dial is set to

AUTO LOCK

NOTE:

During shooting in low light, Auto Focus accuracy may decrease even when Gain Up is used. In this case,

use Manual Focus (੬ pg. 17).

RECORDING Advanced Features (cont.)

Self-Timer

Interval

You can set the delay between pressing RECORDING

START/STOP and the actual start of recording. If you

secure the camcorder, you (or whomever is operating the

camcorder) can enter the scene before recording starts.

Timer Indicator

1MIN

1/2S

Rec Time Indicator

NOTE:

Make sure the camcorder is in the Record-Standby mode

before performing the following steps.

ACCESS MENU SCREEN

Turn the PROGRAM AE select dial to any position

except AUTO LOCK, then press MENU.

NEAR

SET INTERVAL TIME

Press – or + to move the highlight bar down to

“INTERVAL TIMER”, then press FAR or NEAR to

cycle through the choices. Stop when the desired

time appears. Choose from “15S”, “30S”, “1MIN”,

“5MIN”, or select to turn the function “OFF”.

–

FAR

CLOSE MENU

Press MENU.

START DELAYED RECORDING

Tally lamp

Press RECORDING START/STOP. The tally lamp

begins blinking, and the blinking frequency

increases about 5 seconds before recording is to

start. Once recording begins, the lamp stops

blinking but stays lit.

To Release Self-Timer . . .

GAIN UP

S.LX

OFF

..... while the tally lamp is blinking, press RECORDING

START/STOP to stop the blinking, then set

“INTERVAL TIMER” to “OFF”.

TELE MACRO

INTERVAL TIMER OFF

REC TIME

OFF

JLIP ID NO.

SET CHARACTER

DATE/TIME

END :MENU KEY

1/2S

1/4S

OFF

5MIN

1MIN

30S

15S

OFF

Animation

Time-Lapse

Give stationary scenes or objects an illusion of

movement. This function allows you to shoot a

series of pictures, each slightly different, of the same

object for a brief period of time.

You can record sequentially at preset time spans.

Leaving the camcorder aimed at a specific subject,

you can record subtle changes over an extended

period of time.

NOTE:

Make sure the camcorder is in the Record-Standby

mode and the recording mode is set to “SP” before

performing the following steps.

Make sure the camcorder is in the Record-Standby

mode and the recording mode is set to “SP” before

performing the following steps.

ACCESS MENU SCREEN

Turn the PROGRAM AE select dial to any

position except AUTO LOCK, then press

MENU.

position except AUTO LOCK, then press

MENU.

SET RECORDING TIME

SET INTERVAL BETWEEN

Press – or + to move the highlight bar down to

“REC TIME”, then press FAR or NEAR to cycle

through the choices. Stop when the desired

time appears. Choose from “1/4S”, “1/2S”,

“1S”, or select to turn the function “OFF”.

Then press MENU to close Menu screen.

RECORDINGS

Press – or + to move the highlight bar down to

“INTERVAL TIMER”, then press FAR or NEAR

to cycle through the choices. Stop when the

desired time appears. Choose from “15S”,

“30S”, “1MIN”, “5MIN”, or select to turn the

function “OFF”.

START RECORDING

Press the Recording Start/Stop button after

focusing on the subject. The recording stops

automatically after the selected period of time.

SET RECORDING TIME

Press – or + to move the highlight bar down to

“REC TIME”, then press FAR or NEAR to cycle

through the choices. Stop when the desired

time appears. Choose from “1/4S”, “1/2S”,

“1S”, or select to turn the function “OFF”.

Then press MENU to close Menu screen.

ASSEMBLE SERIES OF

PICTURES

Repeat step 3 for the desired number of

pictures.

START TIME-LAPSE

RELEASE ANIMATION MODE

RECORDING

Set “REC TIME” in the Menu screen to “OFF”.

Press the Recording Start/Stop button.

Recording and intervals alternate

automatically.

NOTES:

RELEASE TIME-LAPSE MODE

To release when the tally lamp is not blinking,

set “REC TIME” and “INTERVAL TIMER” in the

Menu screen to “OFF”. To release when the

tally lamp is blinking, press the Recording

Start/Stop button to stop the blinking, then set

“INTERVAL TIMER” and “REC TIME” in the

Menu screen to “OFF”.

● For best results, make sure the camcorder is

secured when shooting in Animation or

Time-Lapse mode.

● Fade-in/out cannot be performed during

Animation or Time-Lapse shooting.

● Before performing other operations following

Animation or Time-Lapse recording, make sure

the Animation or Time-Lapse mode is deactivated.

PLAYBACK Using The Cassette Adapter

Cassette Adapter

Use this to play back a VHS-C video cassette recorded

with this camcorder. It is fully compatible with any VHS

video cassette recorder. The C-P7U adapter is battery

powered and automatically performs tape loading and

unloading.

INSERT BATTERY

Slide the battery cover up to remove it, and install

one “R6(AA)” size battery as shown in the

illustration at left. Then reattach the cover.

VCR

INSERT CASSETTE IN ADAPTER

Slide the latch to open the adapter compartment

door, then insert the cassette and close the

compartment door.

Compartment door

PLAY BACK ON CONNECTED VCR

Load the cassette adapter into the VCR and play the

tape back as you would any other.

REMOVE CASSETTE FROM

ADAPTER

Slide the latch and the compartment door opens

automatically. Then insert your finger in the hole on

the underside of the adapter as shown in the

Sliding latch

Reels

illustration at left, push up and remove the cassette.

Compact video cassette

NOTES:

● During tape loading and unloading, do not touch the

reels for safety and tape protection.

● During special-effect playback (slow motion, still

frame, etc.), the picture may vibrate or noise bars may

appear on the screen.

● To record on a VCR using a compact cassette and the

adapter, cover the adapter’s recording safety hole with

adhesive tape.

Recording safety hole

PLAYBACK Basic Connections

There are three basic types of connections. When making

the connections, refer also to your VCR and TV

instruction manuals.

Connection To A VCR [A]

(Editing, Dubbing and Playback)

NOTE:

Use the provided Audio and Video cables.

To AUDIO and

VIDEO connectors

When

CONNECT CAMCORDER TO VCR

connecting the

cables, open

the jack cover.

As shown in the illustration at left, connect the

Audio and Video

cables (provided)

Audio and Video cables between the AUDIO and

VIDEO connectors on the camcorder and those on

the VCR.

To AUDIO and

VIDEO IN

connectors

SUPPLY POWER

Turn on the camcorder, the VCR and the TV.

SELECT MODE

VCR

Set the VCR to its AUX input mode, and set the TV

to its VIDEO mode.

Antenna

Connection To A TV With A/V Input

Connectors [B] (Playback ONLY)

NOTE:

Use the provided Audio and Video cables.

To AUDIO,

VIDEO and

RF DC OUT

connectors

CONNECT CAMCORDER TO TV

As shown in the illustration at left, connect the

Audio and Video cables between the AUDIO and

VIDEO connectors on the camcorder and those on

the TV.

RF unit RF-V5E

(optional)

SELECT MODE

Set the TV to its VIDEO or AV mode (as specified in

its instructions).

NOTES:

● It is recommended to use the AC Power

Adapter/Charger as the power supply instead

of the battery pack.

Connection To A TV With NO A/V Input

Connectors (Playback ONLY)

● To monitor the picture and sound from the

camcorder without inserting a tape, set the

camcorder’s Power switch to “CAMERA”,

then set your TV to the appropriate input

mode.

● If you have a TV or speakers that are not

specially shielded, do not place the speakers

adjacent to the TV as interference will occur

in the camcorder playback picture.

NOTE:

Use the optional RF-V5E RF unit.

* Refer to the RF-V5E instruction manual for connection

procedure.

PLAYBACK Basic Playback

NOTE:

PLAY/PAUSE

REW FF

Make sure you connect your camcorder as directed in

“Basic Connections” (੬ pg. 27).

LOAD A CASSETTE

Slide EJECT to open the cassette holder, then insert

the cassette with the label facing out. Press PUSH to

ensure the holder is closed and locked.

STOP

SELECT MODE

Set the Power switch to “PLAY”. The Power On

indicator lights.

PLAYBACK

Press PLAY/PAUSE. The playback picture appears in

the viewfinder and the connected TV.

STOP PLAYBACK

Press STOP.

Rewind or Fast-forward the tape

Press REW to rewind, or FF to fast-forward the tape

during Stop mode.

POWER

NOTE:

Recording mode indicator

The camcorder shuts off automatically after about 5

minutes in Stop mode or Still Playback mode. To turn on

again, set the Power switch to “POWER OFF”, then to

“PLAY”.

Tape running

M-0:23:45

indicator

: Playback

: Fast-Forward/

Forward Search

: Rewind/Reverse

Tape counter

6 : Still Playback

PLAYBACK Features

FEATURE:

PURPOSE:

Manual Tracking

To eliminate noise bars that appear

on the screen during playback.

OPERATION:

NOTES:

1) Press either +/– button as many

times as necessary for best picture.

● To reset TRACKING to the original

preset, press both + and – buttons

simultaneously.

–

● Manual Tracking may not work

with tapes recorded on other VCRs

or camcorders.

FEATURE:

PURPOSE:

OPERATION:

Still Playback

To pause during playback.

1) Press PLAY/PAUSE during

playback.

2) To resume normal playback, press

PLAY/PAUSE again.

COUNTER R/M PLAY/PAUSE

NOTE:

Noise bars appear and pictures may

become monochrome during Still

Playback. This is normal.

FEATURE:

PURPOSE:

Shuttle Search

To allow high-speed search in either

direction.

STOP

OPERATION:

Forward Search

1) Press FF during playback.

Reverse Search

1) Press REW during playback.

REW

NOTE:

Noise bars appear and pictures may

become monochrome or darken in

Shuttle Search. This is normal.

FEATURE:

PURPOSE:

Counter Memory Function

To make it easier to locate a specific

tape segment.

OPERATION:

1) Press COUNTER R/M and hold for

more than 2 seconds. The counter

resets to “0:00:00”.

2) Press COUNTER R/M. “M”

appears.

3) After recording or playback, press

STOP, then REW. The tape

automatically stops at or close to

0:00:00.

4) Press PLAY/PAUSE to start

playback.

NOTES:

● The counter memory functions in

the FF and REW modes.

● To disable Counter Memory

Function, press COUNTER R/M so

the “M” disappears.

EDITING

Tape Dubbing

CONNECT EQUIPMENT

Following the illustration at left, connect the

camcorder and the VCR.

PLAY/PAUSE

Power switch

PREPARE FOR DUBBING

Set the camcorder’s Power switch to “PLAY”, turn

on the VCR’s power, and insert the appropriate

cassettes in the camcorder and the VCR.

SELECT VCR MODE

Engage the VCR’s AUX and Record-Pause modes.

FIND EDIT-IN POINT

To AUDIO and

VIDEO OUT

connectors

Engage the camcorder’s Play mode to find a spot

just before the edit-in point. Once it’s reached, press

PAUSE on the camcorder.

When connecting

the cables, open the

jack cover.

START EDITING

Press PLAY on the camcorder and engage the VCR’s

Record mode.

Audio and

Video cable

(provided)

STOP EDITING TEMPORARILY

Engage the VCR’s Record-Pause mode and press

PAUSE on the camcorder.

To AUDIO and

VIDEO IN

EDIT MORE SEGMENTS

connectors

Repeat steps 4 through 6 for additional editing, then

stop the VCR and camcorder when finished.

VCR (Recording deck)

SET REMOTE/VCR CODE

Random Assemble Editing

[R.A.Edit]

SET REMOTE TO OPERATE VCR

Create edited videos easily using your

camcorder as the source player. You can select

up to 8 “cuts” for automatic editing, in any

order you like. R.A.Edit is more easily

performed when the MBR (Multi-Brand

Remote RM-V704U or RM-V700U) is set to

operate with your brand of VCR (see VCR

CODE LIST), but can also be performed by

operating the VCR manually.

Turn off the power to the VCR and point the remote

toward the VCR’s infrared sensor. Then, referring to

the VCR CODE LIST on the left, press and hold MBR

SET, and press button (A) and then (B).

•The code is automatically set once you release the

MBR SET button, and the VCR’s power comes on.

OPERATE THE VCR

Make sure the VCR’s power is on. Then, while

holding VCR CTL, press the button on the remote for

the desired function. The functions the remote can

control are PLAY, STOP, PAUSE, FF, REW and VCR

REC STBY (you don’t need to press VCR CTL for this

one).

MBR SET

VCR CTL

You’re now ready to try Random Assemble Editing.

IMPORTANT

Although the MBR is compatible with JVC VCRs and

those of many other makers, it may not work with yours

or may offer limited functions.

RM-V704U or RM-V700U (optional)

NOTES:

● If the VCR’s power doesn’t come on in step 1, try

another code from the VCR CODE LIST.

● Some brands of VCR don’t come on automatically. In

this case, turn the power on manually and try step 2.

● If the RM-V704U/V700U is not able to control the

VCR, use the controls on the VCR.

VCR CODE LIST

VCR BRAND BUTTONS

NAME

(A) (B)

NAME

(A) (B)

AKAI

2ꢀ

4ꢀ

PHILIPS

9ꢀ

5ꢀ

1ꢀ

4ꢀ

1ꢀ

6ꢀ

2ꢀ

● The RM-V704U/V700U cannot be used to operate the

GR-AX337.

BLAUPUNKT

FERGUSON

7ꢀ

8ꢀ

MAKE CONNECTIONS

SANYO

6ꢀ

GRUNDIG

HITACHI

4ꢀ

CONNECT TO . . .

JVC VCR EQUIPPED WITH REMOTE

SELECO, REX

SHARP

1ꢀ

6ꢀ

PAUSE TERMINAL

Connect the editing cable to the Remote PAUSE

terminal.

5ꢀ

JVC

1ꢀ

6ꢀ

SONY

5ꢀ

`ꢀ

9ꢀ

JVC VCR NOT EQUIPPED WITH REMOTE

MITSUBISHI

NEC

7ꢀ

PAUSE TERMINAL

Connect the editing cable to the R.A.EDIT

connector.

ꢀ

7ꢀ

THOMSON,

TELEFUNKEN,

SABA,

1ꢀ

6ꢀ

7ꢀ

NON-JVC VCR WITH NEITHER

Connect the editing cable to the RM-V704U/

V700U’s Pause-In jack.

PANASONIC

3ꢀ

7ꢀ

1ꢀ

4ꢀ

NORDMENDE

TOSHIBA

9ꢀ

All other connections are as shown in the illustration

on page 32.

CONTINUED ON NEXT PAGE

EDITING (cont.)

REW/FF

PREPARE CAMCORDER

Insert a recorded tape and set the Power switch to

“PLAY”.

STOP

CANCEL

PREPARE VCR

IN/OUT

R.A. EDIT

PLAY/PAUSE

Turn the power on, insert a recordable tape and

engage the AUX mode (refer to VCR’s instructions).

SELECT SCENES

ACCESS R.A. EDIT COUNTER

DISPLAY

Press PLAY/PAUSE, then press R.A. EDIT and the

counter display appears in the viewfinder and the

screen of the connected TV.

Open the cover

Press REW or FF to locate the beginning of a scene

you want, then press IN/OUT to register that point.

The data appears under IN on the display.

To AUDIO

and VIDEO

out connectors

To J terminal

(JLIP)

Editing cable

(optional, 3.5ø

mini-plug cable)

Press REW or FF to locate the end of the scene and

press IN/OUT to register it. The data appears under

OUT on the display. The total time of the registered

scene(s) is displayed at the bottom of the screen.

Audio and

Video cable

(provided)

A B

Repeat steps 2 and 3 for each additional scene

To AUDIO

and VIDEO IN

connectors

To Remote

PAUSE

(as many as 8).

MAKE CORRECTIONS

To Pause-In

Press CANCEL during steps 2 and 3 to erase the

most recently registered point.

VCR (Recording deck)

NOTES:

RM-V704U/V700U

(optional)

● For GR-AX837/AX637 only: The RM-V704U/V700U can

be used to operate other camcorder functions as well.

Point the RM-V704U/V700U at the camcorder’s remote

sensor and press any of the following buttons (function

apears in parentheses):

IN/OUT

CANCEL

VCR REC STBY

ON/OFF

— ON/OFF (camcorder R.A. EDIT)

— IN/OUT (camcorder IN/OUT)

— CANCEL (camcorder CANCEL)

● There must be at least one second between an in-point and

its corresponding out-point.

OUT

● To ensure correct operation, leave at least 15 seconds open

between scenes.

ᮣ 1 0:00:25

0:00:25

0:01:05

0:03:31

0:02:53

0:03:18

0:02:33

ᮣ 4 0:04:11

● Blank portions of tape cannot be registered as in-points or

out-points.

● If it takes more than 5 minutes to search for an in-point, the

VCR’s Record-Pause mode is cancelled and editing doesn’t

take place.

COUNTER

TOTAL

0:00:25

0:00:00

COUNTER

TOTAL

0:04:11

0:01:13

● Pressing R.A.EDIT clears all in- and out-points from

memory.

● Leave a small margin for error around each in-point to

ensure the scene is recorded in its entirety.

AUTOMATIC EDITING TO VCR

ORIGINAL TAPE (camcorder)

ENGAGE VCR’S RECORD–PAUSE

MODE

OUT

IN OUT

OUT

Point the remote control toward the VCR’s infrared

sensor and press VCR REC STBY, or manually

engage the VCR’s Record-Pause mode.

BEGIN AUTOMATIC EDITING

Press EDIT on the camcorder, and the previously

selected scenes are copied to the VCR in the

specified order.

EDITED TAPE (VCR)

STOP

END AUTOMATIC EDITING

When all selected scenes have been copied, the

camcorder and VCR enter the still or pause mode.

Press STOP on both units.

EDIT

•When finished editing, be sure to disconnect the

editing cable and the audio/video cable.

NOTES:

● If you performed step 1 on page 31 (“MAKE

CONNECTIONS”), keep the remote control pointed at

the VCR during editing.

● The on-screen display only appears while the

camcorder searches for each scene.

● There may be noise at in- or out-points on the edited

tape with certain VCRs.

SUPPLEMENTAL INFORMATION ON THE REMOTE CONTROL

Using the RM-V704U/V700U, it is also possible to perform

deck-to-deck Random Assemble Editing. The playback

deck must be an R.A. Edit-capable JVC VCR. The recording

deck can be...

Ⅲ a VCR other than JVC, or

AV OUT

Player (JVC VCR)

Ⅲ a JVC VCR which has neither a Remote PAUSE nor an

R.A. EDIT connector

Editing cable

(optional, 3.5 ø -3.5 ø,

mini-plug cable)

R.A. EDIT

How to use:

— Connect the playback deck and RM-V704U/V700U as

shown on the left.

AV IN

— Set the RM-V704U/V700U to correspond to the brand

of the recording deck. (੬ pg. 31)

Recording deck

— For Random Assemble Editing procedure, please refer to

the instruction manual of the JVC VCR you are using as

the playback deck.

PAUSE IN

Notes:

Ⅲ RM-V704U/V700U cannot be used to control the playback deck.

Ⅲ RM-V704U/V700U is capable of controling basic operations of

the recording deck. While pressing VCR CTL, press PLAY, STOP,

PAUSE, FF or REW for these functions. (Not possible with some

brands and models). Other buttons cannot be used.

RM-V704U or

RM-V700U

(optional)

Ⅲ To put the recording deck in the Record-Pause mode, use the

controls on the recording deck itself.

USING REMOTE CONTROL UNIT (GR-AX837/AX637 only)

The Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic

operations (PLAY, STOP, PAUSE, FF, and REW) of your VCR. This remote control unit makes additional

recording functions possible.

NOTE:

The remote controls cannot operate GR-AX337.

Installing The Battery

PULL OUT BATTERY

HOLDER

Release

Lock hole

Type

: Pull out by inserting a pointed

tab

instrument into slot

: Pull out while sliding the lock

hole.

: Pinch the release tab and pull

out.

INSERT BATTERY

Making sure the plus (+) side is up, insert

the lithium battery (CR2025)* into the

battery holder.

REPLACE BATTERY HOLDER

Insert the battery holder into the remote

control unit, and push the holder until it

clicks into place.

* Read the caution concerning lithium

batteries (੬ pg. 2).

RM-V705U (provided

with GR-AX837/AX637)

RM-V704U or RM-V700U

(optional)

FUNCTIONS

BUTTONS

With the camcorder’s power switch

set to “CAMERA”.

With the camcorder’s power switch set

to “PLAY”.

1 Infrared beam

Transmits the beam signal.

transmitting window

2 ZOOM (T/W) Buttons

3 PLAY Button

Zoom (invariable speed, ੬ pg. 11)

—

Playback start (੬ pg. 28)

Stop (੬ pg. 28)

4 STOP Button

—

5 REW Button

Retake (rewind)/Quick Review (੬ pg. 12)

Rew/Rew Shuttle Search (੬ pg. 28)

Insert Editing (੬ pg. 36)

6 INSERT Button

7 START/STOP Button

8 INT. TIME Button

9 REC TIME Button

0 PAUSE Button

! FF Button

—

Functions same as the Recording Start/Stop button on the camcorder.

Self-Timer/Time-Lapse (੬ pg. 35)

—

Animation/Time-Lapse (੬ pg. 35)

—

Pause (੬ pg. 29)

Retake (forward) (੬ pg. 12)

FF/FF Shuttle Search (੬ pg. 28)

@ A.DUB Button

# PAUSE IN Connector

$ MBR SET Button

% VISS Button

—

Audio dubbing (੬ pg. 37)

੬ pg. 32

—

੬ pg. 31

Index Code marking (੬ pg. 35)

—

^ VCR CTL Button

& R.A.EDIT Buttons

—

੬ pg. 31

੬ pg. 32

# — & : RM-V704U or RM-V700U only.

FEATURE:

PURPOSE:

Self-Timer, Animation and Time-Lapse

The remote control lets you set/release

Interval Timer and Rec Time functions

as well as the Menu screen.

Transmitted beam

effective area

OPERATION:

Self-Timer

1) Set

Instead of performing steps 1 through 3

on pg. 24 (“Self-Timer”), press INT.

TIME on the remote control. Each time

INT. TIME is pressed, the Interval Timer

indicator appears, changing in the

following order: 15S, 30S, 1MIN, 5MIN

and No indication (off).

15°

Remote sensor

15°

(GR-AX837/AX637 only)

When using the remote control, be sure to

point it at the remote sensor. The above

illustration shows the approximate transmitted

beam effective area for indoor use.

The transmitted beam may not be effective or

may cause incorrect operation outdoors or

when the remote sensor is directly exposed to

sunlight or powerful lighting.

2) Release

Instead of setting “INTERVAL TIMER” to

“OFF” in the Menu, press INT. TIME on

the remote control until the Interval

Timer indicator disappears.

Animation

1) Set

Instead of performing steps 1 and 2 on

pg. 25 (“Animation”), press REC TIME

on the remote control. Each time REC

TIME is pressed, the Rec Time indicator

appears, changing in the following

order: 1/4S, 1/2S, 1S and No indication

(off).

Interval Timer Indicator

Viewfinder

2) Release

Instead of using the Menu in step 5 on

pg. 25, press REC TIME on the remote

control until the Rec Time indicator

disappears.

INDEX

1MIN

1/2S

Index Code

Marking

Time-Lapse

1) Set

Rec Time Indicator

Instead of performing steps 1 through 3

on pg. 25 (“Time-Lapse”), press INT.

TIME and REC TIME on the remote

control. Each time INT. TIME is

pressed, the Interval Timer indicator

appears, changing in the following

order: 15S, 30S, 1MIN, 5MIN and No

indication (off). Each time REC TIME is

pressed, the Rec Time indicator

appears, changing in the following

order: 1/4S, 1/2S, 1S and No indication

(off).

2) Release

Instead of using the Menu in step 5 on

pg. 25, press INT. TIME and REC TIME

on the remote control until the

indicators disappear.

NOTE:

Also refer to pgs. 24 and 25.

START/STOP

FEATURE:

Index Code Marking

(RM-V704U/V700U only)

To give you automatic access to any

selected point on a recording.

VISS

INT. TIME

REC TIME

PURPOSE:

OPERATION:

1) Press VISS once to place the index

code. “INDEX” blinks in the

viewfinder during marking.

NOTE:

If VISS is pressed during Record–

Standby mode, the mark is placed

where RECORDING START/STOP is

pressed.

RM-V704U or

RM-V700U

(optional)

RM-V705U

(provided with

GR-AX837/

AX637 only)

USING REMOTE CONTROL UNIT (GR-AX838/AX638 only) (cont.)

Insert Editing

COUNTER R/M

You can record a new scene into a previously recorded

tape, replacing a section of the original recording with

minimal picture distortion at the in- and out-points. The

original audio remains unchanged.

NOTE:

Use the RM-V705U, RM-V704U or RM-V700U remote

control unit to perform this procedure.

SELECT MODE

Set the Power switch to “PLAY”.

FIND EDIT-OUT POINT

Play back the tape, locate the point and press

PAUSE on the camcorder or the remote control.

POWER

RESET COUNTER

Press and hold COUNTER R/M for more than

2 seconds to reset the tape counter, then press for

less than 1 second and make sure “M” appears in

the viewfinder.

M-0:23:45

Tape Counter

Insert editing indicator

FIND EDIT-IN POINT

Press REW to go a little beyond the beginning of the

scene you want to replace, press PLAY to view the

recorded tape, and press PAUSE at exactly at the

point where the new scene should start.

Viewfinder

ENGAGE INSERT EDITING MODE

Press and hold INSERT, and without releasing

INSERT, press and release PAUSE. The Insert

mode is engaged, and the scene the camcorder is

aimed at appears on the screen.

BEGIN INSERT EDITING

Press RECORDING START/STOP. When the counter

reaches “0:00:00”, editing stops automatically and

the camcorder enters the Insert-Pause mode.

END INSERT EDITING

Press STOP.

START/STOP

REW

PLAY

PAUSE

REW

NOTES:

● After step 5, Retake (੬ pg. 12) can be performed.

● The tape may stop slightly before or after the

designated end point, and noise bars may appear.

Neither indicates a defect in the unit.

● Only video signal is recorded in the Insert Editing

mode.

INSERT

RM-V705U

RM-V704U or

RM-V700U

(optional)

(provided with

GR-AX837/

AX637 only)

Audio Dubbing

Audio dubbing indicator

You can record a new soundtrack on a prerecorded tape

(normal audio only).

Viewfinder

M-0:05:20

** Perform steps 1, 2 and 3 of the Insert Editing procedure

(੬ pg. 36) before continuing.

•The sound comes from the built-in mike.

FIND EDIT-IN POINT

Press REW to go a little beyond the beginning of the

scene onto which you want to dub new audio, press

PLAY to view the recorded tape, then press PAUSE

at exactly the point where dubbing should start.

ENGAGE AUDIO DUB STANDBY

MODE

Press and hold A. DUB, and without releasing

A. DUB, press and release PAUSE.

BEGIN AUDIO DUBBING

Mike

Press PLAY. When the counter reaches “0:00:00”,

Audio Dubbing stops automatically and the

camcorder enters the Audio Dub-Standby mode.

END AUDIO DUBBING

Press STOP.

REW

PLAY

PAUSE

NOTES:

● Do not press FF or REW during Audio Dub-Standby, or

the edit points will not be accurate.

REW

● If the mike is too close to the TV, or if the TV’s volume

is too high, whistling or howling may occur.

A. DUB

RM-V704U or

RM-V700U

(optional)

RM-V705U

(provided with

GR-AX837/

AX637 only)

NOTES (for Insert Editing and

Audio Dubbing):

● Insert Editing and audio Dubbing may not work

correctly if the tape contains blank segments, or if the

recording speed was changed during the original

recording.

● To edit/dub onto a tape with the recording safety tab

removed, cover the hole with adhesive tape.

● Do not press STOP during Insert Editing or Audio

Dubbing, or the edit points will not be accurate.

● During Insert Editing and Audio Dubbing, when Insert–

Pause or Audio Dub–Standby is engaged, the counter

may go slightly past “0:00:00”. Recording, however,

stops at exactly 0:00:00.

TROUBLESHOOTING

SYMPTOM

POSSIBLE CAUSE(S)

POWER

No power is supplied.

● The battery pack has not been attached correctly

(੬ pg. 4).

● The battery pack is not charged (੬ pg. 4).

● The power supply has not been correctly connected

(੬ pg. 5).

The power suddenly goes off and

doesn’t come back on by itself.

● The battery pack has completely discharged.

● Remove the cassette and disconnect the power source,

then after a few minutes, try turning the power back on. If

it still doesn’t come on, consult your nearest JVC dealer.

RECORDING

Recording cannot be performed.

● The recording tape’s Erase Protection tab is missing.

Cover the hole with adhesive tape. (Some tapes have

sliding tabs. In this case, check the position of the tab.)

Recording does not start.

● The camcorder Power switch has not been set to

“CAMERA” (੬ pg. 10).

PLAYBACK

The tape is running, but there’s no

playback picture.

● The TV has not been set to its VIDEO mode.

● If A/V connection is used, the TV’s VIDEO/TV switch has

not been set to VIDEO.

Noise bars appear in the playback

picture.

● Manual Tracking has not been performed (੬ pg. 29).

Playback picture is blurred or

interrupted.

● The video heads are dirty or worn out. Consult your

nearest JVC dealer for head cleaning or replacement.

The counter indication is blurred

during Still playback.

● This is normal.

TAPE TRANSPORT

The tape stops during fast-forward or

rewind.

● The Counter Memory Function has been activated

(੬ pg. 29).

Rewinding or fast-forwarding cannot

be performed.

● The tape is already fully wound on one reel or the other.

SYMPTOM

POSSIBLE CAUSE(S)

OTHER

The tape won’t eject.

● The battery pack is running low.

Some functions are not available.

● The PROGRAM AE select dial is set to “AUTO LOCK”.

Vertical white lines appear when

shooting a very bright object.

● This sometimes occurs when the contrast between the

background and the object is great. It is not a defect of

the camcorder.

Bright, crystal-shaped spots appear

in the viewfinder.

● Sunlight is directly entering the lens.

The picture is blurred in the Quick

Review or Retake mode.

● This is normal while recording in the LP mode. Some noise

may be present while recording in the SP mode (੬ pg. 8).

An error number (i.e. E03) appears

in the viewfinder.

● Turn the camcorder’s power off, then disconnect the

power source. After a few minutes, try turning the power

on again. If the error number still appears in the view-

finder, consult your nearest JVC dealer.

The image is out of focus.

● The diopter needs to be adjusted (੬ pg. 6).

● The scene being shot is adversely affecting the operation

of Auto Focus (੬ pg. 16).

A character generator title and the

date and time displays disappear

from the viewfinder.

● If you remove the power source from the camcorder while

the power is on, all settings and selections are erased.

Make sure to turn the camcorder’s power off before

disconnecting the power source.

Even though the Lens Cover is open,

the Lens Cover Warning indicator

blinks.

● The Lens Cover Warning indicator may blink when the

camcorder is used in dark areas, regardless of the position

of the Lens Cover.

The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio,

etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit

(battery pack, AC Power Adapter/Battery Charger, etc.) and clock battery; and then re-connect it and

proceed as usual from the beginning.

INDEX Controls

6 7 8 9 0 !

4 5

% ^ & * ( )

Controls

1 Diopter Adjustment ............................ ੬ pg. 6

2 Power Zoom Lever ............................ ੬ pg. 11

3 BATT. [Battery] RELEASE Switch .........੬ pg. 4

4 Recording Start/Stop Button ................੬ pg. 10

5 POWER Switch .................................. ੬ pg.10,28

6 STOP Button ...................................... ੬ pg. 28

@ REW Button ....................................... ੬ pg. 28

RETAKE R [Quick Review] Button....... ੬ pg. 12

# FF Button ........................................... ੬ pg. 28

RETAKE F Button................................ ੬ pg. 12

$ PLAY/PAUSE Button ........................... ੬ pg. 28

% SELECT Button ................................... ੬ pg. 18

^ SET Button ......................................... ੬ pg. 18

& PROGRAM AE Select Dial .................. ੬ pg. 14

7 Tape Length [T30•45•60]

Select Button...................................... ੬ pg. 8

COUNTER R [Reset]/M [Memory]

* Multi-Function Control

Button ................................................ ੬ pg. 29

•Exposure +/– ................................... ੬ pg. 15

•Focus FAR/NEAR ............................. ੬ pg. 16

•Menu Setting Change ....................... ੬ pg. 22

•Tracking +/– .................................... ੬ pg. 29

8 EDIT Button ....................................... ੬ pg. 33

9 Recording mode [SP/LP] Select

Button ................................................ ੬ pg. 8

R.A.EDIT CANCEL Button ...................੬ pg. 32

( MENU Button .................................... ੬ pg. 22

) PUSH Button ..................................... ੬ pg. 8

q EJECT Switch...................................... ੬ pg. 8

0 R.A.EDIT Button................................. ੬ pg. 32

! R.A.EDIT IN/OUT Button....................੬ pg. 32

W E R T

w Q

e I r t y

Connectors

Other Parts

w J terminal (JLIP (Joint Level Interface Protocol)

o Video Light

Connector.)

(GR-AX837/AX637 only)..................... ੬ pg. 13

(Located beneath the jack cover)

p •Camera sensor

•Connect the Editing Cable when performing

Random Assemble Editing (੬ pg. 32).

•It is used to connect the camcorder to a device

such as a personal computer.

Be careful not to cover this area; built-in

here is the sensor necessary for shooting.

•Remote sensor

(GR-AX837/AX637 only) ..................੬ pg. 35

For further detail consult your nearest JVC

dealer. Information (in English) is also available

at our home page: http://www.jvc-victor.co.jp/

Q Microphone ....................................... ੬ pg. 37

W Shoulder Strap Eyelets ........................ ੬ pg. 9

E Clock Battery Compartment ................ ੬ pg. 6

R Battery Pack Mount ........................... ੬ pg. 4

T Electronic Viewfinder......................... ੬ pg. 6

Y LENS COVER Switch ......................... ੬ pg. 10

U Grip Strap .......................................... ੬ pg. 9

e DC IN Jack ......................................... ੬ pg. 5

The jacks

are located beneath the jack cover.

r VIDEO OUT Jack ............................... ੬ pg. 27

t RF DC OUT Jack

y AUDIO OUT Jack .............................. ੬ pg. 27

I VIDEO LIGHT ON/AUTO/OFF Switch

(GR-AX837/AX637 only)..................... ੬ pg. 13

Indicators

u Tally Lamp ......................................... ੬ pg. 10

O Tripod Mounting Socket ......................੬ pg. 9

i Power On Indicator ........................... ੬ pg. 10

INDEX Viewfinder

1 2 3

6 7

(

)

18MIN

DISP.

T30

REC SP

SEPIA

LENS COVER

–05

MWB

FADE

PAUSE

1MIN

1/2S

INDEX

TAPE END

MERRY CHR ISTMAS

25.12.97 10:24

Viewfinder Indications

1 Cassette Warning/Remaining

% Battery Pack Remaining Power Indicator

Tape Time .......................................... ੬ pg. 10

Changes as follows according to the battery pack’s

remaining power level: “

”.

When no cassette is inserted or when Erase

Protection tab is not in the position that allows

recording, the Cassette ( ) Warning blinks.

Otherwise, the Remaining Tape Time is

displayed.

When the power is almost gone, the indicator

blinks, then the unit shuts off. Replace the

battery pack with a fully charged one.

(Note: The symbol containing 3 darkened

squares —

— does not necessarily mean

2 Recording mode [SP/LP] indicator ......੬ pg. 8

that the battery pack is fully charged.)

3, 9 PROGRAM AE Indicator................੬ pg. 14

Displayed at 3 for approx. 1 second when the

PROGRAM AE select dial is switched from one

position to another. Then only the indicator

remains at 9.

^ Focus Indicator .................................. ੬ pg. 16

& Exposure Level Indicator ..................... ੬ pg. 15

* White Balance Mode Indicator ........... ੬ pg. 21

( Menu Setting Change Indicator........... ੬ pg. 22

) Index Code Marking .......................... ੬ pg. 35

4 Program Manager Function

Indication .......................................... ੬ pg. 18

Appears when the PROGRAM AE select dial is

set to any position other than AUTO LOCK.

q Clock Warning

Displayed for about 5 seconds if the clock

(lithium) battery is not in place or is exhausted

when power is turned on. Also displayed for

about 5 seconds when clock battery becomes

exhausted while using the camcorder.

For inserting or replacing the clock

5 Lens Cover Warning .......................... ੬ pg. 10

6 Tape Length Display .......................... ੬ pg. 8

7 Zoom Level Indicator......................... ੬ pg. 11

8 Recording Indicator ........................... ੬ pg. 10

0 Fade–Standby Indicator ......................੬ pg. 18

battery .................................................. ੬ pg. 6

w Condensation Warning

! Interval Time/Recording

When this indication appears, all functions are

disabled. Turn the unit off (without removing the

power source) for a few hours, and when you

turn it on again the indicator should disappear.

Time Indicator.................................... ੬ pg. 24

@ Record–Standby Mode Indicator.........੬ pg. 10

# Instant Title Display ........................... ੬ pg. 19

$ Date/Time Character Display ..............੬ pg. 20

e Tape End Display ............................... ੬ pg. 10

Appears when the end of the tape is reached

during playback, recording or fast-forward.

CAUTIONS

DANGER:

.... charge in an environment where

temperatures are within the tolerances shown

in the chart below. This is a chemical

reaction type battery—cooler temperatures

impede chemical reaction, while warmer

temperatures can prevent complete charging.

.... store in a cool, dry place. Extended exposure

to high temperatures will increase natural

discharge and shorten service life.

.... avoid prolonged uncharged storage.

.... remove from charger or powered unit when

not in use, as some machines use current

even when switched off.

•The video light becomes extremely hot. Do not

touch it either while in operation or soon after

turning it off, otherwise serious injury may result.

•Do not place the camcorder into the carrying case

immediately after using the video light, since it

remains extremely hot.

•When operating, keep a distance of about 30 cm

between the video light and people or object.

•Do not use near flammable or explosive materials.

•Consult your nearest JVC dealer for replacing the

video light unit.

3. To prevent damage to the camcorder . . .

.... replace the battery pack when it begins to

deliver less recording time per charge.

General Battery Precautions

•When the C-P6U or C-P7U (cassette adapter) is

not functioning even when correctly operated, the

batteries are exhausted. Replace them with fresh

ones.

NOTE:

It is normal for the battery pack to be warm after

charging, or after use.

•Use only the following batteries:

C-P6U or C-P7U .................... R6 (AA) size

Temperature Ranges

Charging ................................... 10°C to 35°C

Operation ................................. 0°C to 40°C

Storage...................................... –10°C to 30°C

Please make note of the following rules for battery

use. When misused, batteries can leak or explode.

NOTES:

1. Refer to the instructions when replacing the

battery.

2. Do not expose batteries to excessive heat as they

can leak or explode.

3. Do not dispose of batteries in a fire.

4. Remove batteries from the unit if it is to be stored

for an extended period to avoid battery leakage

which can cause malfunctions.

● Recharging time is based on room temperature of

20°C.

● The lower the temperature, the longer recharging

takes.

Cassettes

To properly use and store your cassettes, be sure to

read the following cautions:

Battery Packs

1. During use . . .

The supplied battery pack is a nickel-

cadmium battery. Before using the

supplied battery pack or an optional

battery pack, be sure to read the

following cautions:

.... make sure the cassette bears the VHS-C

mark.

.... be aware that recording onto prerecorded

tapes automatically erases the previously

recorded video and audio signals.

.... make sure the cassette is positioned properly

when inserting.

.... do not load and unload the cassette

repeatedly without allowing the tape to run

at all. This slackens the tape and can result in

damage.

1. To avoid hazard . . .

Terminals

.... do not burn.

.... do not short-circuit the terminals.

.... do not modify or disassemble.

.... use only specified chargers.

.... do not open the front tape cover. This

exposes the tape to fingerprints and dust.

2. To prevent damage and prolong service

life . . .

2. Store cassettes . . .

.... do not subject to unnecessary shock.

.... avoid repeated charging without fully

discharging.

.... away from heaters or other heat sources.

.... out of direct sunlight.

.... where they won’t be subject to unnecessary

shock or vibration.

.... where they won’t be exposed to strong

magnetic fields (such as those generated by

motors, transformers or magnets).

.... vertically, in their original cases.

CAUTIONS (cont.)

About moisture condensation . . .

Main Unit

•You have observed that pouring a cold liquid into

a glass will cause drops of water to form on the

glass‘ outer surface. This same phenomenon

occurs on the head drum of a camcorder when it

is moved from a cool place to a warm place, after

heating a cold room, under extremely humid

conditions or in a place directly subjected to the

cool air from an air conditioner.

1. For safety, DO NOT . . .

.... open the camcorder’s chassis.

.... disassemble or modify the unit.

.... short-circuit the terminals of the battery pack.

Keep it away from metallic objects when not

in use.

.... allow inflammables, water or metallic objects

to enter the unit.

.... remove the battery pack or disconnect the

power supply while the power is on.

.... leave the battery pack attached when the

camcorder is not in use.

•Moisture on the head drum can cause severe

damage to the video tape, and can lead to internal

damage to the camcorder itself.

Serious malfunctioning

2. Avoid using the unit . . .

.... in places subject to excessive humidity or

dust.

If malfunctioning occurs, stop using the unit

immediately and consult your local JVC dealer.

.... in places subject to soot or steam such as

near a cooking stove.

.... in places subject to excessive shock or

vibration.

For Your Maintenance

1. After Use

.... near a television set.

1 Set the power switch to POWER OFF to turn

.... near appliances generating strong magnetic

or electric fields (speakers, broadcasting

antennas, etc.).

.... in places subject to extremely high (over

40°C) or extremely low (under 0°C)

temperatures.

off the camcorder.

2 Slide EJECT to open the cassette holder, then

remove the cassette.

3 Close and lock the cassette holder by pressing

PUSH.

4 Press BATT. RELEASE to remove the battery

pack.

3. DO NOT leave the unit . . .

.... in places of over 50°C.

5 Slide the LENS COVER open/close switch to

.... in places where humidity is extremely low

(below 35%) or extremely high (above 80%).

.... in direct sunlight.

.... in a closed car in summer.

.... near a heater.

close the lens cover.

2. Cleaning The Camcorder

1 CLEAN EXTERIOR

Wipe gently with a soft cloth.

2 CLEAN LENS

4. To protect the unit, DO NOT . . .

.... allow it to become wet.

Blow it with a blower brush, then wipe gently

with lens cleaning paper.

.... drop the unit or strike it against hard objects.

.... subject it to shock or excessive vibration

during transportation.

.... keep the lens directed at extremely bright

objects for long periods.

.... direct the eyepiece of the viewfinder at the

sun.

.... carry it by holding the viewfinder.

.... swing it excessively when using the shoulder

strap.

3 REMOVE EYEPIECE

Turn the eyepiece counterclockwise and pull

it out.

4 CLEAN VIEWFINDER

Remove dust using a blower brush.

5 RE-ATTACH EYEPIECE

Align the marks, re-attach the eyepiece and

turn it clockwise.

NOTES:

5. This camcorder features a built-in head

cleaner which automatically cleans the

heads and head drum when a cassette is

loaded or unloaded. If, however, the heads

become dirty and cause blurriness or

interruption in the playback picture,

consult your nearest JVC dealer.

● Avoid using strong cleaning agents such as

benzine or alcohol.

● Cleaning should be done only after the battery

pack has been removed or other power units have

been disconnected.

● Mold may form if the lens is left dirty.

SPECIFICATIONS

GENERAL

AUDIO

Output

Format

Power source

Power consumption

: VHS PAL standard

: DC 6 V

: –8 dBs, 1 k-ohm

(via AUDIO out

connector)

• GR-AX837 light on : 8.5 W

• GR-AX837 light off : 5.5 W

• GR-AX637 light on : 8.3 W

• GR-AX637 light off/

AC POWER ADAPTER/BATTERY CHARGER

(AA-V11EG)

Power requirement

: AC 110 to 240 V`,

50/60 Hz

GR-AX337

Signal system

Video recording system

Luminance

: 5.3 W

: PAL-type

Power consumption

Output

: 23 W

: DC 8.5 V

(CHARGE),

DC 6.3 V

(VTR)

, 1.3 A

, 1.8 A

: FM recording

: Converted sub-carrier

direct recording

Conforms to VHS

standard

Colour

Charging system

: Constant current, peak

detection, timer

controlled

Cassette

Tape speed

cassette

Dimensions

Weight

: 150 (W) x 42 (H) x

68 (D) mm

: Approx. 350 g

: 23.39 mm/sec

: 11.70 mm/sec

Recording time Max.

CASSETTE ADAPTER (C-P7U)

: 60 minutes

(with EC-60 cassette)

: 120 minutes

Dimensions

: 188 (W) x 25 (H) x

104 (D) mm

(with EC-60 cassette)

Weight

Accessory

: Approx. 240 g

: “R6 (AA)”-size battery x 1

Operating temperature : 0°C to +40°C

Operating humidity

Storage temperature

Weight

: 35% to 80%

: –20°C to +50°C

Provided Accessories ......................੬ pg. 3

• GR-AX837

• GR-AX637

• GR-AX337

Dimensions

: Approx. 810 g

: Approx. 825 g

: Approx. 820 g

Optional Accessories

•Battery Packs BN-V12U, BN-V22U, BN-V25U

•Car Battery Charger BH-V3E

•Battery Charger BH-VC10EG

•Car Battery Cord AP-V7E

• GR-AX837

: 112 (W) x 112 (H) x

211 (D) mm

• GR-AX637/AX337 : 112 (W) x 112 (H) x

232 (D) mm

•Compact VHS-C Cassettes EC-60/45/30

•Active Carrying Bag CB-V7U

•Wireless Remote Control Unit RM-V704U or

RM-V700U

The RM-V704U/V700U cannot be used to operate

the GR-AX337.

The GR-AX337 can use the RM-V704U/V700U

only for R.A. Edit with a non-JVC VCR.

CAMERA

Pick up

Lens

: 1/4” format CCD

: F1.6, f = 3.8 to 68.4 mm,

18:1 power zoom lens

with auto iris and macro

control, filter diameter

46 mm

: Electronic viewfinder

with

•0.5” B/W CRT

Some acccessories are not available in some areas.

Please consult your nearest JVC dealer for details on

accessories and their availability.

Viewfinder

Specifications shown are for SP mode unless

otherwise indicated. E. & O. E. Design and

specifications subject to change without notice.

(GR-AX637/AX337)

•0.55” colour LCD

(GR-AX837)

White balance adjustment : Auto/Manual adjustment

VIDEO

Output

: 1 Vp-p, 75 ohms,

unbalanced (via VIDEO

out connector)

PYLE Audio PYLE Dryver Series PLAD214 User Manual
Pioneer XM Digital Satellite Data Audio Receiver GEX P10XMT User Manual
Perlick BC24 Series User Manual
Patterson Kelley MACH 05 User Manual
Panasonic AG HPG10P User Manual
Optimus 120 2155 User Manual
Nikon 10x25DCF User Manual
Motorola MOTOROKR S9 User Manual
McIntosh Radio MR85 User Manual
Kramer Electronics Car Amplifier PT 101R User Manual