ENGLISH
CONTENTS
SAFETY PRECAUTIONS
COMPACT
VHS CAMCORDER
2 – 3
PROVIDED ACCESSORIES
4
AUTOMATIC
DEMONSTRATION
6
GR-SXM947UM
GETTING STARTED
7 – 16
VIDEO RECORDING &
PLAYBACK
17 – 26
VIDEO RECORDING............18 – 21
VIDEO PLAYBACK ..............22 – 26
DIGITAL STILL CAMERA (D.S.C.)
RECORDING &
PLAYBACK
27 – 34
D.S.C. RECORDING ............28 – 29
D.S.C. PLAYBACK ..............30 – 34
ADVANCED
FEATURES
35 – 53
54 – 69
REFERENCES
TROUBLESHOOTING ............55 – 57
DETAILS ...........................58 – 59
INDEX .............................60 – 63
TERMS ............................64 – 65
CAUTIONS ........................66 – 68
SPECIFICATIONS .........................69
INSTRUCTIONS
LYT0732-001A
EN
EN3
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all
sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)
No naked flame sources, such as lighted candles, should be placed on the apparatus.
When discarding batteries, environmental problems must be considered and the local rules or laws
governing the disposal of these batteries must be followed strictly.
The apparatus shall not be exposed to dripping or splashing.
Do not use this equipment in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases,
potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
IMPORTANT SAFETY INSTRUCTIONS
(1) Read these instructions.
(2) Keep these instructions.
(3) Heed all warnings.
(10) Use only with the cart,
stand, tripod, bracket, or
table specified by the
manufacturer, or sold with
the apparatus. When a
cart is used, use caution
when moving the cart/
apparatus combination to avoid injury from
tip-over.
(4) Follow all instructions.
(5) Do not use this apparatus near water.
(6) Clean only with dry cloth.
(7) Do not block any ventilation openings.
Install in accordance with the
(11) Unplug this apparatus during lightning
storms or when unused for long periods of
time.
manufacturer’s instructions.
(8) Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
(12) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
(9) Only use attachments/accessories specified
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
by the manufacturer.
PROVIDED ACCESSORIES
4
EN
•AC Adapter
AP-V10U
•Cassette Adapter
(VHS Playpak)
C-P7U
•Battery Pack
BN-V11U
•Remote Control
Unit RM-V715U
•Shoulder Strap
•Lens Cap
•CD-ROM
•AAA (R03) Battery x 2
(for Remote Control Unit)
•AA (R6) Battery
(for Cassette Adapter)
The CD-ROM contains
the following 4 software
programs:
• Picture Navigator
Presto!
• Mr. Photo
• PhotoAlbum
• ImageFolio
(for Windows® PC)
•PC Connection Cable
EN5
How To Attach The Lens Cap
To protect the lens, attach the provided lens cap to the camcorder as shown in the illustration.
1
2
3
AUTOMATIC DEMONSTRATION
6
EN
Automatic Demonstration takes place when “DEMO MODE” is set to “ON”
(factory-preset).
Ⅲ Available when the Power Switch is set to “ ” or “ ” and the VIDEO
DEMO MODE
mode is selected (the DSC Lamp is not lit).
OFF
ON
Ⅲ Operating the Power Zoom Lever during the demonstration stops the
demonstration temporarily. If the Power Zoom Lever is not moved for
more than 1 minute after that, the demonstration will resume.
Ⅲ “DEMO MODE” remains “ON” even if the camcorder power is turned
off.
Ⅲ To cancel Automatic Demonstration, set the Power Switch to “ ” and
press the MENU Wheel in while the demo is in progress. This takes you
directly to the demo mode’s Setting Menu (so you will not have to go
through the main Menu Screen). Rotate the MENU Wheel to select
“OFF” and press it.
EX I T
Setting Menu
NOTES:
● When a tape whose Erase Protection tab is in the position that allows recording is loaded in the
camcorder, demonstration is not available.
● If you do not detach the Lens Cap, you cannot see the actual changes of the Automatic Demonstration
activated on the LCD monitor or viewfinder.
GETTING STARTED
EN7
GETTING STARTED
CONTENTS
Power..................................................8 – 9
Grip Adjustment ......................................... 10
Viewfinder Adjustment.................................. 10
Shoulder Strap Attachment ............................. 10
Tripod Mounting.......................................... 10
Date/Time Settings...................................... 11
Recording Format Setting ........................ 12 – 13
Recording Mode Setting................................. 14
Tape Length Setting...................................... 14
Loading/Unloading A Cassette ......................... 15
Picture Mode Setting .................................... 16
GETTING STARTED
8
EN
Hook on.
Power
1
This camcorder’s 2-way power supply system lets you
choose the most appropriate source of power. Do not use
provided power supply units with other equipment.
CHARGING THE BATTERY PACK
Push in.
2
Make sure the battery pack is attached to the
1
camcorder. Hook its end to the camcorder 1 and
push the battery in until it locks in place 2.
•If the battery pack is attached in the wrong position,
a malfunction may occur.
BATTERY RELEASE Switch
REFRESH Button
Set the Power Switch to “OFF”. Connect the AC
2
3
Adapter to the camcorder 3.
REFRESH Lamp
CHARGE Lamp
Plug the AC Adapter into an AC outlet 4.
The CHARGE lamp on the camcorder blinks to
indicate charging has started.
When the CHARGE lamp stops blinking but stays lit,
charging is finished. Unplug the AC Adapter from the
AC outlet. Disconnect the AC Adapter from the
camcorder.
Battery pack
Power Switch
4
To Detach The Battery Pack . . .
.... slide BATTERY RELEASE and pull out the battery pack.
To DC IN
connector
3
NOTES:
● During charging or discharging, the camcorder cannot
be operated.
4
AC Adapter
● Charging and discharging is not possible if the wrong
type of battery is used.
To AC outlet
● When charging the battery pack for the first time or after
a long storage period, the CHARGE lamp may not light.
In this case, remove the battery pack from the
camcorder, then try charging again.
● If the battery operation time remains extremely short
even after having been fully charged, the battery is worn
out and needs to be replaced. Please purchase a new
one.
● Using the optional AA-V15 AC Power Adapter/Charger,
you can charge the BN-V11U/V12U/V20U/V400U
battery pack without the camcorder. However, it cannot
be used as an AC adapter.
Battery pack
Charging time
BN-V11U
approx. 1 hr. 30 min.
approx. 1 hr. 30 min.
approx. 2 hrs. 20 min.
approx. 4 hrs. 30 min.
BN-V12U (optional)
BN-V20U (optional)
BN-V400U (optional)
REFRESH:
Charging a battery with some charge remaining reduces that battery’s capacity. Perform the procedure
below to fully discharge the battery pack before recharging.
1. Perform steps 1 through 3 of “CHARGING THE BATTERY PACK”.
2. Press REFRESH on the camcorder for over 2 seconds. The REFRESH lamp on the camcorder blinks to
indicate discharging has started.
3. When discharging is finished, charging automatically starts and the CHARGE lamp blinks.
When you are not using a battery pack for a long period of time, be sure to fully discharge it before storing
because leaving a battery with some charge left over also reduces performance.
For other notes, ੬ pg. 58
EN9
USING THE BATTERY PACK
ATTENTION:
Perform step 1 of “CHARGING THE BATTERY PACK”
Before detaching the power source, make
sure that the camcorder’s power is turned
off. Failure to do so can result in a
camcorder malfunction.
(੬ pg. 8).
Approximate recording time (unit: min.)
Battery pack
Viewfinder on
LCD monitor on
80
(45)
65
(35)
BN-V11U
BN-V12U
(optional)
80
65
Charge marker
(45)
(35)
A charge marker is provided on
the battery pack to help you
remember whether it has b een
charged or not. Two colors are
provided (red and black)—you
choose which one means
charged and which means
discharged.
BN-V20U
(optional)
130
(75)
105
(60)
BN-V400U
(optional)
305
(185)
245
(160)
(
) : when the video light is on
NOTES:
● Recording time is reduced significantly under the
following conditions:
•Zoom or Record-Standby mode is engaged repeatedly.
•The LCD monitor is used repeatedly.
● Before extended use, it is recommended that you
prepare enough battery packs to cover 3 times the
planned shooting time.
USING AC POWER
Use the AC Adapter (connect as shown in the illustration).
NOTES:
●The provided AC Adapter features automatic voltage
selection in the AC range from 110 V to 240 V.
●For other notes, ੬ pg. 58.
To DC IN
connector
AC Adapter
To AC outlet
GETTING STARTED (cont.)
Grip Adjustment
10
EN
Power Zoom
Lever
Separate the Velcro strip.
1
2
3
Recording
Start/Stop
Button
Pass your right hand through the loop and grasp the
grip.
Adjust so that your thumb and fingers can easily
operate the Recording Start/Stop Button and Power
Zoom Lever. Refasten the Velcro strip.
3
Viewfinder Adjustment
2
180°
Set the Power Switch to “ ” or “ ”.
1
2
3
Adjust the viewfinder manually for best viewability.
1
Turn the Diopter Adjustment Control until the
indications in the viewfinder are clearly focused.
Set to “ ” or
”.
“
Shoulder Strap Attachment
PAUSE
Following the illustration, thread the strap through the
1
2
eyelet 1, then fold it back and thread it through the
buckle 2. Repeat the procedure to attach the other
end of the strap to the other eyelet 3, making sure
the strap is not twisted.
2
3
1
Adjust as shown in the illustration 4.
4
Tripod Mounting
Align the screw and camera direction stud on the
1
tripod with the camera’s mounting socket and stud
hole. Then tighten the screw.
CAUTION:
When using a tripod, be sure to open and extend
its legs fully to Stabilize the camcorder. To
prevent damage to the unit caused by falling
over, do not use a small-sized tripod.
EN11
Date/Time Settings
Set the Power Switch to “ ”. The VIDEO Lamp
1
2
3
comes on.
VIDEO Lamp
Press the MENU Wheel in. The Menu Screen
appears.
Rotate the MENU Wheel to select “ TO SYSTEM
MENU” and press it to display SYSTEM MENU.
Rotate the MENU Wheel to select “ NEXT” and
press it to display the next page.
MENU Wheel
Rotate the MENU Wheel to select “DATE/TIME” and
4
5
press it. The DATE/TIME Menu appears.
To set “YEAR”, “MONTH”, “DAY” or “TIME” (hour/
minute), rotate the MENU Wheel to select the desired
item, and press it. When the setting begins blinking,
rotate the MENU Wheel until the correct setting
appears and then press it. The setting stops blinking.
Power Switch
Display
CAMERA MENU
Menu Screen
ᮣ
TO SYSTEM MENU
When none of these settings (“YEAR”, “MONTH”,
“DAY”, “TIME”) blinks, rotate the MENU Wheel to
select “EXIT”, and press it. The Menu Screen
reappears with the highlight bar on “ RETURN”.
FOCUS
AUTO
AUTO
AUTO
6
7
EXPOSURE
M. W. B.
SYSTEM MENU
Press the MENU Wheel in to close the Menu Screen.
ᮣ
NEXT
REC MODE
D. ZOOM
SP
50
x
NOTE:
To display the date and time in the camcorder’s display and
on a connected TV, see “Date/Time Insert” (੬ pg. 47).
SYSTEM MENU
TO CAMERA MENU
ᮣ
REC T I ME
OFF
I NT. T I ME
TELE MACRO
T I TLE LANG.
DATE / T I ME
DEMO MODE
OFF
OFF
ENGL I SH
OFF
ᮣ
RETURN
DATE / T I ME
DATE/TIME Menu
YEAR
MONTH
DAY
2001
JUN
28
:
T I ME
PM
8
20
12-hour
indication with
AM or PM
EX I T
For other notes, ੬ pg. 58
GETTING STARTED (cont.)
12
EN
Recording Format Setting
Set the recording format according to the format of the
tape used or type of recording you wish to perform.
Set the Power Switch to “ ”. The VIDEO Lamp
VIDEO Lamp
1
2
3
comes on.
Press the MENU Wheel in. The Menu Screen
appears.
MENU Wheel
Rotate the MENU Wheel to select “ TO SYSTEM
MENU” and press it to display SYSTEM MENU.
If a VHS cassette is loaded . . .
.... rotate the MENU Wheel to select “S-VHS ET”,
then press it. The S-VHS ET Setting Menu
appears.
If an S-VHS cassette is loaded . . .
.... rotate the MENU Wheel to “S-VHS”, then press
it. The S-VHS Setting Menu appears.
Power Switch
Display: when a VHS cassette is loaded.
Rotate the MENU Wheel to set to either of the
parameters, then press it. The Menu Screen reappears
with the highlight bar on “ RETURN”.
SYSTEM MENU
4
5
Menu Screen
ᮣ
NEXT
REC MODE
D. ZOOM
WI DE
SP
50
x
In the S-VHS ET Setting Menu,
OFF
ON
–
S
VHS ET
ON : Records with S-VHS picture quality on a VHS
cassette (factory-preset). This is called Super
VHS ET (Expansion Technology).
TAPE LENGTH
D I SPLAY
P I CTURE
T
30
FULL
F I NE
FULL
SNAPSHOT
OFF: Records in VHS.
In the S-VHS Setting Menu,
ON : Records in S-VHS on an S-VHS cassette
(factory-preset).
OFF: Records in VHS on an S-VHS cassette.
When an S-VHS
cassette is
loaded: S-VHS
ᮣ
RETURN
–
S
VHS ET
Setting Menu
ON
OFF
Press the MENU Wheel in to close the Menu Screen.
•When the S-VHS ET mode is engaged, “S-ET” is
displayed.
•During S-VHS record mode, “S“ is displayed.
•When S-VHS ET or S-VHS recording starts,
“S-VHS REC” is displayed for approx. 3 seconds.
EX I T
NOTE:
SYSTEM MENU
ᮣ
NEXT
If a cassette is not loaded, “S-VHS” will be displayed in the
REC MODE
D. ZOOM
WI DE
SP
50
Menu Screen.
x
OFF
ON
–
S
VHS ET
TAPE LENGTH
D I SPLAY
P I CTURE
T
30
FULL
F I NE
FULL
SNAPSHOT
ᮣ
RETURN
Normal Screen
EN13
NOTES about S-VHS and S-VHS ET
Ⅲ JVC EHG (Extra High Grade) tapes are recommended for superior results.
Use S-VHS tape for storing recordings for an extended period or for recording important scenes, as it
enables higher-quality recording and playback.
Ⅲ With some tapes, better picture quality may not be obtained even with S-VHS ET recording. It is
recommended that you do test record beforehand to make sure whether better results can be obtained.
Ⅲ If the S-VHS ET mode or recording format is switched during recording, the playback picture will be
blurred at the switching point.
Ⅲ It is recommended that tapes recorded in the SP mode on this camcorder be played back on this
camcorder.
Ⅲ Noise may appear on-screen when tapes recorded in the EP mode are played back.
Ⅲ Tapes recorded in S-VHS or S-VHS ET mode can be played back not only on this camcorder but also on
a Super VHS VCR or a VCR equipped with the SQPB (S-VHS QUASI PLAYBACK) function.
— When tapes recorded in S-VHS or S-VHS ET mode are played back on a VCR equipped with the
SQPB (S-VHS QUASI PLAYBACK) function, S-VHS picture quality is not available.
— Tapes recorded in S-VHS ET mode cannot be played back on some VCRs, including some JVC VCRs.
Ⅲ Tapes recorded in S-VHS or S-VHS ET mode cannot be played back correctly on a normal VHS VCR.
Ⅲ You can play back S-VHS ET recordings not only on this camcorder but also on another VHS VCR
equipped with S-VHS ET.
— It is recommended to specifically label S-VHS ET recordings so you can easily distinguish them from
regular VHS recordings.
Ⅲ S-VHS ET does not work with S-VHS tapes.
Ⅲ To avoid on-screen noise, do not perform Still Playback or Shuttle Search repeatedly.
Ⅲ If the picture contains a lot of jitter or noise, use a cleaning cassette.
Compatibility Between S-VHS And VHS
Recording
Playback
Blank tape
Camcorder
Recorded tape
Cassette adapter
S-VHS VCR
VHS VCR with SQPB
function
S-VHS-C
cassette
S-VHS
recordings
•The recorded format (S-VHS or
VHS) is automatically detected
when playback begins.
S-VHS ET
recordings
Regular VHS VCR
VHS-C
cassette
VHS
recordings
•S-VHS recorded tapes cannot be
viewed on regular VHS VCRs,
other than those equipped with the
SQPB (S-VHS QUASI PLAYBACK)
function.
GETTING STARTED (cont.)
14
EN
Recording Mode Setting
Set the tape recording mode depending on your preference.
Set the Power Switch to “ ”. The VIDEO Lamp
VIDEO Lamp
1
2
3
4
comes on.
Press the MENU Wheel in. The Menu Screen
appears.
MENU Wheel
Power Switch
Rotate the MENU Wheel to select “ TO SYSTEM
MENU” and press it to display SYSTEM MENU.
Rotate the MENU Wheel to select “REC MODE” and
press it. The REC MODE Menu appears. Select “SP”
or “EP” by rotating the MENU Wheel and press it.
The Menu Screen reappears with the highlight bar on
Display
“
RETURN”. Press the MENU Wheel in to close the
Menu Screen.
REC MODE
REC MODE Menu
•“EP” (Extended Play) is more economical, providing
three times the recording time.
SP
EP
NOTE:
If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.
EX I T
SP
Recording mode
indicator
Tape Length Setting
Set the tape length according to the length of the tape
used.
Display
Perform steps 1 through 3 above.
TAPE LENGTH
TAPE LENGTH
Menu
1
2
3
T
T
T
T
20
30
35
40
Rotate the MENU Wheel to select “TAPE LENGTH”,
then press it. The TAPE LENGTH Menu appears.
Rotate the MENU Wheel to select the correct tape
length setting.
EX I T
•T20=20 minutes
•T30=30 minutes
T
30
Tape length
indicator
•T35=35 minutes
•T40=40 minutes
(in SP)
Press the MENU Wheel in. The Menu Screen
reappears with the highlight bar on “ RETURN”.
Press the MENU Wheel in to close the Menu Screen.
4
NOTE:
The tape remaining time (੬ pg. 18) is correct only if the
correct tape length has been selected.
EN15
EJECT Switch
Cassette holder
Loading/Unloading A Cassette
Open the LCD monitor fully.
1
Slide EJECT until the cassette holder opens. Do not
2
3
4
5
use force to open.
Insert or remove a cassette. When inserting, make
sure the label is facing outward.
Press the Close button to close the cassette holder
until it locks into place.
Close Button
Close the LCD monitor.
NOTES:
● Closing the LCD monitor while the cassette holder is still
open may cause damage to the LCD monitor.
● The cassette holder can’t be opened unless a power
supply is attached.
Turn to take
up slack.
● Make sure that the tape is not slack when loading the
cassette. If there is any slack, turn the gear on the
cassette in the direction of the arrow to take up the
slack.
Erase Protection tab
Gear
● Make sure the Erase Protection tab is in the position that
allows recording. If not, slide the tab. Some cassettes
have removable tabs. If the tab has been removed, cover
the hole with adhesive tape.
● The cassette holder cannot be opened while the
camcorder is in the record mode.
GETTING STARTED (cont.)
16
EN
Picture Mode Setting
The Picture mode can be selected to best match your
needs. Two Picture modes are available: FINE and
STANDARD (in order of quality).
VIDEO Lamp
Set the Power Switch to “ ”. The VIDEO Lamp
1
2
3
4
comes on.
Press the MENU Wheel in. The Menu Screen
appears.
MENU Wheel
Rotate the MENU Wheel to select “ TO SYSTEM
MENU” and press it to display SYSTEM MENU.
Rotate the MENU Wheel to select “PICTURE” and
press it. The PICTURE Menu appears. Select “FINE”
or “STANDARD” by rotating the MENU Wheel and
press it. Selection is complete.
Power Switch
The Menu Screen reappears with the highlight bar on
Display
5
“
RETURN”. Press the MENU Wheel in to close the
SYSTEM MENU
Menu Screen
Menu Screen.
ᮣ
NEXT
REC MODE
D. ZOOM
WI DE
SP
50
x
OFF
ON
Picture Quality
Mode
Approximate Number of
Storable Images
–
S
VHS
TAPE LENGTH
D I SPLAY
T
30
FULL
F I NE
FULL
P I CTURE
SNAPSHOT
FINE
30
60
ᮣ
STANDARD
RETURN
NOTES:
P I CTURE
PICTURE Menu
● The number of storable images depends on the selected
Picture mode as well as the composition of the subjects
in the images.
F I NE
STANDARD
● The numbers listed above are applicable when the
camcorder’s memory is empty (when there are no
sample images stored).
EX I T
SYSTEM MENU
ᮣ
NEXT
REC MODE
D. ZOOM
WI DE
SP
50
x
OFF
ON
–
S
VHS
TAPE LENGTH
D I SPLAY
P I CTURE
T
30
FULL
F I NE
FULL
SNAPSHOT
ᮣ
RETURN
Normal Screen
VIDEO RECORDING & PLAYBACK
EN17
VIDEO RECORDING
&
PLAYBACK
CONTENTS
VIDEO RECORDING....................... 18–21
Shooting While Watching The Viewfinder ........ 18
Shooting While Watching The LCD Monitor ....... 18
LCD Monitor Brightness Adjustment .............. 18
Power Switch Position ............................. 18
Journalistic Shooting ................................ 19
Self-Recording ....................................... 19
Zooming ............................................. 20
Picture Stabilizer .................................... 20
Quick Review (for scenes recorded onto a tape) .... 21
Retake ............................................... 21
Video Light .......................................... 21
VIDEO PLAYBACK ........................ 22–26
LCD Monitor Brightness Adjustment .............. 22
Speaker Volume Control ............................ 22
Still Playback ........................................ 22
Shuttle Search ....................................... 22
Tracking .............................................. 23
TBC (Time Base Corrector) ......................... 23
Counter Memory Function .......................... 23
Playback Special Effects ............................ 23
Basic Connections ............................ 24 – 25
Tape Dubbing ........................................ 25
Using The Cassette Adapter (VHS Playpak) ...... 26
VIDEO RECORDING
18
EN
NOTE:
REFRESH Button
Makes the DSC lamp go out.
You should already have performed the procedures listed
below. If not, do so before continuing.
● Power (੬ pg. 8)
● Load A Cassette (੬ pg. 15)
● Recording Mode Setting (੬ pg. 14)
● Tape Length Setting (੬ pg. 14)
● Grip Adjustment (੬ pg. 10)
● Viewfinder Adjustment (੬ pg. 10)
Shooting While Watching The Viewfinder
Make sure the LCD monitor is closed and locked.
1
Press in the tabs on the lens cap to remove it. Set the
Power Switch to “ ” or “ ”. If the DSC Lamp is lit,
press REFRESH for approx. 1 second to select
“VIDEO”. The VIDEO Lamp lights and the camcorder
enters the Record-Standby mode. “PAUSE” is
displayed in the viewfinder.
During shooting
Power Switch
Recording Start/Stop Button
Press the Recording Start/Stop Button. “
” appears
Tape remaining
time indicator
(Approximate)
25M I N
2
in the viewfinder while recording is in progress.
To Stop Recording . . .
.... press the Recording Start/Stop Button. The camcorder
re-enters the Record-Standby mode.
MIN
(Now calculating)
120MIN
119MIN
0MIN
(Blinking)
1MIN
(Blinking)
2MIN
(Blinking)
3MIN
Shooting While Watching The LCD Monitor
Make sure the LCD monitor is fully open. Press in the
1
tabs on the lens cap to remove it. Set the Power
Switch to “ ” or “ ”. If the DSC Lamp is lit, press
REFRESH for approx. 1 second to select “VIDEO”.
The VIDEOLamp lights and the camcorder enters the
Record-Standby mode. “PAUSE” is displayed in the
LCD monitor.
BRIGHT Wheel
90°
180°
Tilt the LCD monitor upward/downward for best
2
viewability and press the Recording Start/Stop Button.
“
” appears in the LCD monitor while recording is
in progress.
–
– – – – – – – – – –
6
+
BR I GHT
NOTE:
When you use the LCD monitor outdoors in direct
sunlight, the LCD monitor may be difficult to see. If this
happens, use the viewfinder instead.
To Adjust The Brightness Of The LCD Monitor
.... rotate the BRIGHT Wheel until the bright
level indicator on the display moves and
the appropriate brightness is reached.
To Stop Recording . . .
.... press the Recording Start/Stop Button. The camcorder
re-enters the Record-Standby mode.
Power Switch Position
: Suitable for standard recording using NO special effects or manual adjustments.
: Allows you to set recording functions using the menus for more creative capabilities.
OFF : Switches off the camcorder.
: Allows you to play back your recordings.
EN19
NOTES:
● If the Record-Standby mode continues for 5 minutes without performing Zoom or any other operations, the
camcorder’s power shuts off automatically. Set the Power Switch to “OFF”, and then back to “ ” or “ ” to
turn the camcorder on again.
● If you are recording on a cassette from the middle (such as when a tape is removed and re-inserted during
recording), use the Retake function (੬ pg. 21) to find the end of the last recording so you do not erase any
of it.
● To remove the indications from the camcorder’s display during recording, ੬ pg. 40, 42.
Self-Recording
JOURNALISTIC SHOOTING
SELF-RECORDING
In some situations, different shooting angles may
provide more dramatic results. Hold the camcorder in
the desired position and tilt the LCD monitor in the
most convenient direction. It can rotate 270° (90°
downward, 180° upward).
You can shoot yourself while viewing your own
image in the LCD monitor. Open the LCD monitor
and tilt it upward 180° so that it faces forward, then
point the lens toward yourself and start recording.
For other notes, ੬ pg. 59
VIDEO RECORDING (cont.)
20
EN
Zooming: To produce the zoom in/out effect, or an
instantaneous change in image magnification.
Digital circuitry extends the maximum magnification offered
by optical zoom. This system is called Digital Zoom.
Zoom In
Zoom in (T: Telephoto)
Slide the Power Zoom Lever towards “T”.
Zoom Out
Slide the Power Zoom Lever towards “W”.
● The further you slide the Power Zoom Lever, the quicker
the zoom action.
Zoom out (W: Wide angle)
● Focusing may become unstable during Zooming. In
this case, set the zoom while in Record–Standby, lock
the focus by using the manual focus (੬ pg. 45), then
zoom in or out in Record mode.
● The zoom level indicator (5) moves during zoom.
Once the zoom level indicator reaches the top of the
zoom indicator bar, all magnification from that point is
through digital processing.
RETAKE (2/3) Button
LIGHT
OFF/AUTO/ON
Switch
● When using Digital Zoom, the quality of image may
suffer. To deactivate Digital Zoom, set “D.ZOOM” to
“OFF” in SYSTEM MENU (੬ pg. 41).
● Digital zoom cannot be used when the “VIDEO
ECHO” mode (੬ pg. 39) is activated.
Power Zoom Lever
P. STABILIZER
Button
Picture Stabilizer: To compensate for unstable
images caused by camera-shake, particularly at high
magnification.
1) Press P. STABILIZER. “ ” appears.
2) To switch off the Picture Stabilizer, press
P. STABILIZER. The indicator disappears.
● Accurate stabilization may not be possible if hand shake
is excessive, or under the following conditions:
•When shooting subjects with vertical or horizontal
stripes.
•When shooting dark or dim subjects.
•When shooting subjects with excessive backlighting.
•When shooting scenes with movement in various
directions.
Display
Zoom indicator
bar
1
x
Zoom level
indicator
Approximate
zoom ratio
•When shooting scenes with low-contrast backgrounds.
● Switch off the Picture Stabilizer when recording with
the camcorder on a tripod.
Picture Stabilizer indicator
● The “
” indicator appears blinking if the Stabilizer
cannot be used.
● This function cannot be activated during the “Night-
Alive” (੬ pg. 36), “CLASSIC FILM”, “STROBE” and
“VIDEO ECHO” mode (੬ pg. 39).
EN21
Video Light: To brighten the scene when
Quick Review (for scenes
natural lighting is too dim.
recorded onto a tape): To check the end
1) Set LIGHT OFF/AUTO/ON as required:
OFF : Turns off the light.
AUTO : Automatically turns on the light when the
camcorder senses insufficient lighting on
the subject.
of the last recording.
1) Make sure the camcorder is in the Record–Standby
mode.
2) Press
2
and release quickly.
Tape is rewound for approx. 2 seconds and
played back automatically, then pauses in
Record–Standby mode for the next shot.
● Distortion may occur at the start of playback. This
is normal.
ON
: Always keeps the light on as long as the
camcorder is turned on.
● The video light can only be used with the
camcorder’s power on.
● It is recommended to set the white balance
Retake: To re-record certain segments.
(੬ pg. 46) to
when you use the video light.
1) Make sure the camcorder is in the Record–Standby
mode.
● When not using the video light, turn it off to save
battery power.
● Even if the battery indicator (
2) Press and hold either RETAKE to reach the start
) does not blink
point for new recording. Pressing
tape and pressing reverses it.
3
forwards the
if the battery pack’s charge is low, the camcorder
may turn off automatically when you turn on the
video light, or when you start recording with the
video light turned on.
● When LIGHT OFF/AUTO/ON is set to “AUTO”:
•Depending on the lighting conditions, the video
light may keep turning on and off. In this case,
manually switch the light on or off using LIGHT
OFF/AUTO/ON.
2
3) Press the Recording Start/Stop Button to start
recording.
● Noise bars appear and pictures may become
monochrome or darken during Retake. This is
normal.
•While the “Sports” or “High Speed Shutter”
mode (੬ pg. 38) is engaged, the light is likely
to stay on.
•While the “Twilight” mode (੬ pg. 38) is
engaged, the light will not activate.
DANGER
Ⅲ The video light can become extremely hot.
Do not touch it either while in operation or
soon after turning it off, otherwise serious
injury may result.
Ⅲ Do not place the camcorder into the carrying
case immediately after using the video light,
since it remains extremely hot for some time.
Ⅲ When operating, keep a distance of about
30 cm (11-13/16") between the video light and
people or objects.
Ⅲ Do not use near flammable or explosive
materials.
Ⅲ It is recommended that you consult your
nearest JVC dealer for replacing the video
light.
VIDEO PLAYBACK
22
EN
REFRESH Button
Makes the DSC lamp go out.
Load a tape (੬ pg. 15).
1
2
Set the Power Switch to “
”. If the DSC Lamp is
lit, press REFRESH for approx. 1 second to select
“VIDEO”.
To start playback, press 4/6.
•To stop playback, press 5.
Stop (5) Button
•Press
2
to rewind, or
3
to fast-forward the tape
during Stop mode.
Rewind (2) Button
NOTES:
Play/Pause (4/6) Button
● The camcorder shuts off automatically after about
5 minutes in Stop mode. To turn on again, set the Power
Fast-Forward (3) Button
Switch to “OFF”, then to “
”.
● When the Power Switch is set to “
” and the LCD
BRIGHT Wheel
monitor is opened at an angle of 60 degrees or more, the
LCD monitor switches on and the viewfinder switches
off automatically to save power.
● The playback picture can be viewed in the viewfinder
(with the LCD monitor shut), on the LCD monitor or on
a connected TV (੬ pg. 24, 25).
Power Zoom
Lever (VOL.)
● You can also view the playback picture on the LCD
monitor with it flipped over and retracted.
● If a blank portion on the tape is played back, the screen
may become black. This is not a malfunction.
Speaker
Set to “
”.
LCD Monitor Brightness Adjustment: Rotate the BRIGHT Wheel towards “+” to brighten, or
towards “–” to darken.
● The Bright Level Indicator is displayed under the Date/Time Display when you play back images recorded in
Wide Mode (੬ pg. 41).
Speaker Volume Control: Slide the Power Zoom Lever (VOL.) towards “+” to turn up the volume,
or towards “–” to turn down the volume.
● The Speaker Volume Indicator is displayed under the Date/Time Display when you play back images
recorded in Wide Mode (੬ pg. 41).
Still Playback: Pauses during playback.
1) Press 4/6 during playback.
2) To resume normal playback, press 4/6 again.
● Noise bars will appear and the picture will become monochrome during Still Playback.
● If TBC (੬ pg. 23) is engaged, noise bars will not appear. This mode is called Fine Still.
Shuttle Search: Allows high-speed search in either direction.
1) Press
3
for forward or
2
for reverse search during playback.
2) To resume normal playback, press 4/6.
● During playback, press and hold or 3. The search continues as long as you hold the button. Once you
release it, normal playback resumes.
● Noise bars appear and pictures may become monochrome or darken during Shuttle Search. This is normal.
2
EN23
Tracking: Eliminates noise bars that appear on-screen
REFRESH Button
Makes the DSC lamp go out.
during playback. Factory-preset is Auto Tracking.
To activate Manual Tracking:
1) Press the TRACKING Wheel for approx. 2 seconds.
“MT” appears.
COUNTER R/M Button
2) Rotate the TRACKING Wheel so that the noise bars
disappear.
● To return to Auto Tracking, press the TRACKING Wheel
for approx. 2 seconds or set the Power Switch to “OFF”
and then ”
” again. “AT” blinks. When Auto
Stop (5) Button
Tracking finishes, the indication disappears.
● When noise bars appear during playback, the
camcorder enters the Auto Tracking mode and “AT” is
displayed.
Rewind (2) Button
Play/Pause (4/6) Button
● Manual Tracking may not work with tapes recorded on
other VCRs or camcorders.
Fast-Forward (3) Button
TRACKING
TBC (Time Base Corrector): Removes jitter from
fluctuating video signals to deliver a stable picture even
with old tapes. Factory-preset: TBC is engaged.
To activate/release the TBC mode, press TBC during
playback for more than 1 second. When the TBC mode is
activated, “TBC” is displayed.
Wheel
TBC Button
Counter Memory Function: Makes it easier to
locate a specific tape segment.
1) Press COUNTER R/M and hold for more than 1 second.
The counter resets to “0:00:00”.
2) Press COUNTER R/M for less than 1 second.
“M” appears.
Set to “
”.
3) After recording or playback, press 5, then 2. The tape
automatically stops at or close to 0:00:00.
4) Press 4/6 to start playback.
● The counter memory functions in the Fast-Forward and
Rewind modes.
● To disable the Counter Memory Function, press
COUNTER R/M for less than 1 second so that “M”
disappears.
Playback Special Effects (CLASSIC FILM,
MONOTONE, SEPIA, STROBE and VIDEO
ECHO, ੬ pg. 39): Allows you to add creative
effects to the playback image.
1) Activate the TBC mode and Auto Tracking.
2) Press DIGIFECT repeatedly until the desired mode’s
name and indication appear. They are displayed for
approx. 2 seconds, then the name disappears so that
only the indication remains. The mode is activated.
3) To cancel the effect, select “OFF” in step 2.
● Playback Special Effects do not work during shuttle
search.
● The selected effect mode cannot be changed during still
playback.
For other notes, ੬ pg. 59
VIDEO PLAYBACK (cont.)
24
EN
Basic Connections
These are some basic types of connections. When making the connections, refer also to your VCR and TV
instruction manuals.
A. Connection to a TV or VCR equipped with an S-VIDEO IN and A/V input connectors
Use optional S-Video and Audio cables.
To TV or VCR
TV
To S-Video
Input
To S-Video
Output
S-Video cable
(optional)
VCR
Audio cable
(optional)
To Audio
Input
To Audio
Output
Connector cover*
*When connecting the cables, open this cover.
B. Connection to a TV or VCR equipped only with A/V input connectors
Use optional Video and Audio cables.
To TV or VCR
TV
To Audio
Input
To Audio
Output
Audio cable
(optional)
VCR
Video cable
(optional)
To Video
Input
To Video
Output
Connector cover*
*When connecting the cables, open this cover.
EN25
Basic Connections
Tape Dubbing
Make sure all units are turned off.
Following the illustration on pg. 24, connect the
camcorder and the VCR.
1
2
1
2
Connect the camcorder to a TV or VCR as
Set the camcorder’s Power Switch to “
turn on the VCR’s power, and insert the
”,
shown in the illustration (੬ pg. 24).
If using a VCR . . . go to step 3.
If not . . . go to step 4.
appropriate cassettes in the camcorder and the
VCR.
Connect the VCR output to the TV input,
Engage the VCR’s AUX and Record-Pause
3
4
5
referring to your VCR’s instruction manual.
3
4
modes.
Turn on the camcorder, the VCR and the TV.
Engage the camcorder’s Play mode to find a
spot just before the edit-in point. Once it is
reached, press 4/6 on the camcorder.
Set the VCR to its AUX input mode, and set the
TV to its VIDEO mode.
Press 4/6 on the camcorder and engage the
VCR’s Record mode.
5
6
7
NOTES:
Engage the VCR’s Record-Pause mode and press
4/6 on the camcorder.
● It is recommended to use the AC Adapter as the
power supply instead of the battery pack
(੬ pg. 9).
Repeat steps 4 through 6 for additional editing,
then stop the VCR and camcorder when
finished.
● If your VCR has an S-Video input connector,
connect the camcorder and the VCR using an
optional S-Video cable. This can improve the
dubbed picture quality.
NOTE:
If you wish to dub still images recorded with the DSC
Lamp lit, play back the still images (੬ pg. 30, 31),
and instead of doing the above steps 4 through 6,
engage the VCR’s Record mode and record them
onto a tape.
● To monitor the picture and sound from the
camcorder without inserting a tape, set the
camcorder’s Power Switch to “ ” or “ ”, then
set your TV to the appropriate input mode.
● Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound
when the camcorder is turned on.
● If you have a TV or speakers that are not specially
shielded, do not place the speakers adjacent to the
TV as interference will occur in the camcorder
playback picture.
VIDEO PLAYBACK (cont.)
26
EN
Using The Cassette Adapter (VHS Playpak)
Use this to play back an S-VHS-C/VHS-C video cassette
recorded with this camcorder on a VHS VCR. It is fully
compatible with any S-VHS/VHS video cassette recorder.
The cassette adapter is battery powered and automatically
performs tape loading and unloading.
Slide the battery cover up to remove it, install one
1
2
“AA (R6)” size battery as shown, then reattach the
cover.
Slide the latch to open the adapter compartment
door, then insert the cassette and close the compart-
ment door.
VCR
Load the cassette adapter into the VCR and play the
tape back as you would any other.
Compartment door
3
4
Slide the latch and the compartment door opens
automatically. This may take around 10 seconds. Do
not attempt to force the adapter open. Then, insert
your finger in the hole on the underside of the
adapter as shown in the illustration at left, and push
up and remove the cassette.
NOTES:
●During tape loading and unloading, do not touch the
reels for safety and tape protection.
●Tapes recorded in S-VHS or S-VHS ET mode cannot be
played back on a regular VHS VCR. Playback is possible
with a VCR equipped with the S-VHS or SQPB (S-VHS
QUASI PLAYBACK) function.
Sliding latch
Compact video cassette
●During special-effect playback (slow motion, still frame,
etc.), the picture may vibrate or noise bars may appear
on the screen.
Reels
●To record on a VCR using a compact cassette and the
adapter, cover the adapter’s recording safety hole with
adhesive tape.
Recording safety hole
DIGITAL STILL CAMERA (D.S.C.) RECORDING & PLAYBACK
EN27
DIGITAL STILL CAMERA
(D.S.C.) RECORDING
&
PLAYBACK
CONTENTS
D.S.C. RECORDING ...................... 28–29
Quick Review
(for still images stored in the built-in memory) .... 29
D.S.C. PLAYBACK ........................ 30–34
Normal Playback .................................... 30
Slide Show ........................................... 30
INDEX Screen ........................................ 31
Index Playback ...................................... 31
Protecting Images ................................... 32
Deleting Images ..................................... 33
Connection To A Windows® PC .................... 34
D.S.C. RECORDING
28
EN
When shooting a still image, it is not recorded onto the
tape, but it is stored in the camcorder's built-in memory in
the selected Picture Mode. A stored still image data can be
transferred to a PC, saved, and processed using a Paint
Software program or Mr. Photo Gold (੬ pg. 34).
A still image processed on the PC can be also inserted
onto a tape (੬ pg. 53).
REFRESH Button
Makes the DSC lamp come on.
Stop (5) Button
MODE SELECTION
Rewind (2) Button
Press in the tabs on the lens cap to remove it, then set
1
the Power Switch to “ ”. The VIDEO Lamp comes
on. If the DSC Lamp is not lit, press REFRESH for
approx. 1 second to select “DSC”. An image appears.
Play/Pause (4/6) Button
SNAPSHOT Button
MENU
Wheel
To select the Picture Mode, perform steps 2 through 4
2
3
of “Picture Mode Setting” on pg. 16.
Rotate the MENU Wheel to select “SNAPSHOT”, and
press it. The SNAPSHOT Menu appears.
Rotate the MENU Wheel to select the appropriate
mode among the 4 Snapshot modes (੬ pg. 29), and
press it. Selection is complete.
The Menu Screen reappears with the highlight bar on
During shooting
4
“
RETURN”. Press the MENU Wheel in again to
close the Menu Screen.
Power Switch
Display
STILL IMAGE STORAGE
Menu Screen
TAPE LENGTH
T
30
Press SNAPSHOT.
P I CTURE
F I NE
FULL
1
•Regardless of the Power Switch position (“ ” or
SNAPSHOT
“
”), Snapshot recording takes place using the
ᮣ
RETURN
selected Snapshot mode.
•The remaining number of shots available is
displayed.
SNAPSHOT
SNAPSHOT Menu
FULL
To Delete Unwanted Still Images . . .
–
P I N UP
–
–
MULT I
MULT I
4
9
When the remaining number indicator displays “0”
(blinking), it is not possible to continue storing pictures
until you delete some shots to make room for new ones.
Perform “DELETE” function in the Menu Screen to remove
pictures you do not need (੬ pg. 33).
EX I T
TAPE LENGTH
P I CTURE
SNAPSHOT
T
30
F I NE
–
P I N UP
ᮣ
RETURN
Normal Screen
Snapshot mode
indicator
P
P (PIN-UP)
M4 (MULTI-4)
M9 (MULTI-9)
No indication (FULL)
EN29
NOTES:
DSC
F I NE 15
Remaining number
of shots
● Some sample images have been stored in the built-in
memory at the factory. If you wish to delete them, first
remove the “Protecting Images” function (੬ pg. 32),
then perform the “Deleting Images” function (੬ pg.
33).
60 59
1
0
(Blinking)
Pictrue mode display
● If a Snapshot is taken while the camcorder is in the
WIDE mode (੬ pg. 41), the Snapshot image is
recorded without the black bars at the top and bottom of
the screen.
D.S.C. mode indicator
● When you shoot in a dark environment, the still image
will become coarse and its true colors will be lost.
● During the D.S.C. recording, the Zooming (੬ pg. 20),
Picture Stabilizer (੬ pg. 20) and Video Light
(੬ pg. 21) functions can be operated.
FULL*
(Snapshot mode with
no frame)
● Still images are taken in a format based on JPEG (Joint
Photographic Experts Group).
● When you use the LCD monitor outdoors under direct
sunlight, the LCD monitor may be difficult to see. If this
happens, close the LCD monitor and use the viewfinder
instead.
● To store the still images you shot, we recommend that
you transfer them to a computer and save them on disk
(੬ pg. 34), or transfer them to a VCR connected to the
camcorder and record them onto a tape.
PIN-UP*
(Pin-Up mode)
● Image data stored in the camcorder’s built-in memory
can be transferred to a Windows® PC and saved using
the provided image transfer software, Picture Navigator
(੬ pg. 34).
MULTI-4**
(Multi-Analyzer 4)
* There is a momentary camera shutter-type blackout
together with the image.
** Continuous camera shutter-type blackout takes place 4
or 9 times with the image, like serial photography, then
the 4 or 9 still images you took are displayed.
Quick Review (for still images stored
in the built-in memory): To check the still
image most recently stored in the built-in memory.
MULTI-9**
(Multi-Analyzer 9)
1) Set the Power Switch to “ ” or “ ”. If the DSC Lamp
is not lit, press REFRESH for approx. 1 second to select
“DSC”.
2) Press
2
and release quickly.
● The still image is displayed for approx. 3 seconds. The
message “DELETE OK? PRESS PLAY BUTTON”
appears.
To remove the still image you have checked
(Instant Delete) . . .
Press 4/6 while the message “DELETE OK? PRESS PLAY
BUTTON” is displayed.
D.S.C. PLAYBACK
30
EN
REFRESH Button
Makes the DSC lamp come on.
Normal Playback
Still images shot using this camcoder are automatically
numbered, then stored in numerical order in the built-in
memory. You can view the still images stored in memory,
one at a time, much like flipping through a photo album.
Set the Power Switch to “
”. The VIDEO Lamp
1
2
comes on. If the DSC Lamp is not lit, press REFRESH
for approx. 1 second to select “DSC”. A still image
stored in memory is displayed.
Previous Page (2) Button
Next Page (3) Button
•When no still image is stored in memory, the screen
becomes blue.
MENU (BRIGHT)
Wheel
Press
view.
3
or
2
to select the still image you want to
•Each time
2
3
is pressed, the page goes back, while
is pressed, the page goes next.
Power Switch
each time
•If there are no stored images, “NO IMAGES
STORED” is displayed.
NOTES:
● When the Power Switch is set to “
” and the LCD
monitor is opened at an angle of 60 degrees or more, the
LCD monitor switches on and the viewfinder switches
off automatically to save power.
● The playback picture can be viewed in the viewfinder
(with the LCD monitor shut), on the LCD moitor or on a
connected TV (੬ pg. 24).
Display
To move
the page
next
● When viewing a playback picture on a connected TV, it
may jitter slightly.
● You can also view the playback picture on the LCD
monitor with it flipped over and retracted.
● To brighten the LCD monitor, rotate the BRIGHT Wheel
towards “+”. To darken the LCD monitor, rotate it
towards “–”.
● Even if you shoot a new picture after playing back a still
image with a low number, this will not overwrite the
existing picture because new pictures are automatically
stored after the still image most recently stored in
memory.
To move
the page
back
Slide Show
You can run through all the images stored in memory
automatically in numerical order.
Display
MENU
Set the Power Switch to “
”. If the DSC Lamp is
Menu Screen
I NDEX
SL I DE SHOW
PROTECT
1
not lit, press REFRESH for approx. 1 second to select
DELETE
“DSC”.
Press the MENU Wheel in. The Menu Screen
ᮣ
RETURN
2
3
4
appears.
Rotate the MENU Wheel to select “SLIDE SHOW”
and press it. The Slide Show starts.
To stop the Slide Show, press the MENU Wheel in
twice.
EN31
Picture mode
Index number
INDEX Screen
The images you shot can be displayed together with their
index information. Convenient for checking images shot
beforehand, the INDEX Screen also shows the Picture
mode as well as which images are protected against
accidental erasure.
Selected image
EXIT
01
<
INDEX
02
>
06
01: Index number
Index numbers are marked from 01. For example, when
10 images are stored (index number: 01 to 10), if three
images with index numbers 02, 04 and 06 are deleted
from memory, the remaining images are automatically
moved up to fill any gaps in the numerical sequence.
Therefore, the number of remaining images is 7, and the
new index numbers range from 01 to 07.
04
05
: Picture mode
Protect icon
Displays the Picture mode of the stored image. There are 2
modes available: FINE and STANDARD (੬ pg. 16). A star
mark is displayed next to still images shot in the FINE
mode. There are no marks next to still images shot in the
STANDARD mode.
: Protect icon
When an image is protected against its accidental erasure,
a padlock mark appears next to the Picture mode
indicator, and that image cannot be deleted.
Selected Image
An image is framed like this when it is selected. Rotate
MENU to move the frame to the desired image.
Index Playback
You can view all still images stored in memory six at a
time. Use this mode when looking for a still image you
want to view and when checking the still images you shot
beforehand.
Display
Set the Power Switch to “
”. If the DSC Lamp is
EXIT
01
<INDEX>
INDEX Menu
02
03
06
1
not lit, press REFRESH for approx. 1 second to select
“DSC”.
04
Press the MENU Wheel in. The Menu Screen
appears.
2
3
4
Rotate the MENU Wheel to select “INDEX” and press
it. The INDEX Menu appears.
Playback Screen
Rotate the MENU Wheel to select the desired still
image, then press it. The one you selected is
displayed on the whole screen, then the screen enters
normal playback.
•If the desired still image cannot be found, place the
highlight bar on “EXIT”, then press the MENU
Wheel in twice to exit the menu.
NOTE:
On the Index Menu, a star mark is displayed next to a still
image you shot in the FINE mode.
D.S.C. PLAYBACK (cont.)
32
EN
REFRESH Button
Protecting Images
The Protect mode helps prevent the accidental erasure of
images. When a padlock mark is displayed next to the
Picture Mode indication, that image cannot be deleted.
Makes the DSC lamp
come on.
Set the Power Switch to “
”. If the DSC Lamp is
1
not lit, press REFRESH for approx. 1 second to select
“DSC”.
Press the MENU Wheel in. The Menu Screen
MENU Wheel
2
3
appears.
Rotate the MENU Wheel to select “PROTECT” and
press it. The PROTECT Menu appears.
TO PROTECT AN IMAGE
Before doing the following, perform steps 1 through 3
above.
Power Switch
Display
Rotate the MENU Wheel to move the frame to the
desired image and press it. A “ ” padlock mark
appears on the selected image.
Repeat this procedure for all images you do not wish
to delete by accident.
MENU
4
5
Menu Screen
I NDEX
SL I DE SHOW
PROTECT
DELETE
Rotate the MENU Wheel upward to select “EXIT”,
then press it twice. The normal playback screen
appears.
ᮣ
RETURN
NOTE:
EXIT
01
<
PROTECT
02
>
PROTECT Menu
When the memory is initialized or corrupted, even
protected images are deleted. If you do not want to lose
important images, transfer them to a PC and save them.
03
06
04
05
TO REMOVE PROTECTION
Before doing the following, perform steps 1 through 3
above.
Padlock mark
Rotate the MENU Wheel to move the frame to the
Normal playback
If Protection is
removed
4
5
desired image and press it. The “ ” padlock mark
located above the image disappears and the image is
no longer protected.
EXIT
01
<
PROTECT
02
>
Repeat this procedure for all images from which you
wish to remove protection.
03
06
Rotate the MENU Wheel upward to select “EXIT”,
then press it twice. The normal playback screen
appears.
04
05
Normal playback
EN33
REFRESH Button
Deleting Images
Previously shot images can be deleted either one at a time or
all at once.
Set the Power Switch to “
”. If the DSC Lamp is not
lit, press REFRESH for approx. 1 second to select “DSC”.
Makes the DSC lamp
1
2
3
come on.
Press the MENU Wheel in. The Menu Screen appears.
MENU Wheel
Power Switch
Rotate the MENU Wheel to select “DELETE” and press it.
The DELETE Menu appears.
TO SELECT AN IMAGE BY BROWSING
IMAGES STORED IN MEMORY
Before doing the following, perform steps 1 through 3 above.
Rotate the MENU Wheel to select “SELECT” and press it.
Display
The Delete Select Menu appears.
4
5
DELETE
DELETE Menu
SELECT
ALL
Rotate the MENU Wheel to move the frame to the desired
image that you wish to delete and press it. An “
appears above the selected image.
Repeat this procedure for all images that you wish to
delete.
”
In case of “ALL”
EX I T
Rotate the MENU Wheel upward to select “NEXT” and
press it. The Delete Execute Menu appears.
6
7
NEXT <DELETE>
Delete Select
Menu
Rotate the MENU Wheel to select “ENTER” and press it.
After “ENTER” blinks, the selected images are deleted
and the Menu Screen reappears. Press the MENU Wheel
in again to close the Menu Screen.
•To cancel deletion, rotate the MENU Wheel to select
“CANCEL” and press it twice. The Menu Screen closes.
01
02
06
04
05
In case of
“SELECT”
TO DELETE ALL IMAGES
Before doing the following, perform steps 1 through 3 above.
DELETE
Delete Execute
Menu
Rotate the MENU Wheel to select “ALL” and press it. The
Delete Excute Menu appears.
CANCEL
ENTER
4
5
Rotate the MENU Wheel to select “ENTER” and press it.
After “ENTER” blinks, all the images are deleted and the
Menu Screen reappears. Press the MENU Wheel in
again to close the Menu Screen.
•To cancel deletion, rotate the MENU Wheel to select
“CANCEL” and press it twice. The Menu Screen closes.
Menu Screen
NOTES:
● Before deleting some still images stored in memory, perform
“Protecting Images” for the necessary ones (੬ pg. 32) or
save them on a PC so that you do not lose them accidentally
(੬ pg. 34).
CAUTION:
While “ENTER” is selected on the Delete
Execute Menu and it is blinking, switching
off the camcorder or removing the power
supply unit (battery pack or AC Adapter)
may cause the camcorder’s built-in memory
to become corrupt. Never remove the
power supply unit at this stage.
● Protected images (੬ pg. 32) cannot be deleted with the
above operation. To delete them, remove protection first.
● If the remaining number of shots is not 30 in the FINE mode
or 60 in the STANDARD mode when “ALL” is selected on
the DELETE Menu, initialize the camcorder’s memory
(੬ pg. 57).
D.S.C. PLAYBACK (cont.)
Connection To A Windows® PC
34
EN
Makes the DSC lamp come on.
Image data stored in the camcorder’s built-in memory can
be transferred to a Windows® PC and saved using the
image transfer software, Picture Navigator. The image data
transferred to a Windows® PC can also be further
processed using Mr. Photo Gold, and the still image
processed on the PC can be inserted onto a tape
(੬ pg. 53).
To assure safety, make sure all units are turned off before
making any connection.
Connect the camcorder’s DIGITAL connector to the
1
2
COM Port (RS-232C) on a Windows® PC, using the
provided PC connection cable.
Set the Power Switch to “
”. The VIDEO Lamp
comes on. If the DSC Lamp is not lit, press REFRESH
for approx. 1 second to select “DSC”. A still image
stored in memory appears.
To DIGITAL
connector
Open the cover.
•When transferring still images to a computer, be
sure that a still image is displayed on the screen.
Launch the provided software on your Windows® PC.
Transfer the still images stored in the camcorder’s
memory to the Windows® PC. Refer to the software’s
instruction manual on the provided CD-ROM for
details.
PC connection
cable (provided)
3
4
•During transfer of the still image, the camcorder’s
screen becomes blue and “
” is
For Windows®:
To COM Port
(RS-232C)
displayed. After transferring is finished, the screen
displays the same still image as in step 2.
Close the software, then switch off the camcorder.
NOTES:
● Before transferring still images from your personal computer to the camcorder’s built-in memory, perform the
camcorder’s Picture Mode Setting (੬ pg. 16). The still images will be transferred from the personal
computer in the selected Picture Mode.
● When transferring still images from your personal computer to the camcorder, make sure the number of
images to be transferred is smaller than the camcorder’s remaining number of shots available.
● Use the AC Adapter as the power supply instead of the battery pack.
● The still images stored in the camcorder’s memory are not automatically removed after being transferred to
the PC. If you wish to remove those still images from the camcorder’s memory, delete them (੬ pg. 33).
● Windows® are trademarks of Microsoft Corporation, registered in the U.S.A. and other countries.
ADVANCED FEATURES
EN35
ADVANCED FEATURES
CONTENTS
Night-Alive .................................................................. 36
Fade/Wipe Effects.......................................................... 37
Program AE With Special Effects .......................................... 38
Digital Effects ............................................................... 39
Using Menus For Detailed Adjustment .............................40 – 42
Snapshot..................................................................... 43
Exposure Control............................................................ 44
Focusing ..................................................................... 45
White Balance Adjustment ................................................. 46
Manual White Balance Operation ......................................... 46
Date/Time Insert ........................................................... 47
Instant Titles ................................................................ 47
Animation.................................................................... 48
Time-Lapse .................................................................. 48
USING THE REMOTE CONTROL UNIT ...................... 49–53
Installing The Batteries ................................................ 50
Playback Zoom ......................................................... 51
Animation And Time-Lapse ............................................ 51
Insert Editing (VIDEO) ................................................. 52
Insert Editing
(Insert A Still Image From The Built-In Memory Onto A Tape) ..... 53
Audio Dubbing .......................................................... 53
ADVANCED FEATURES
36
EN
REFRESH Button
Night-Alive
Makes dark subjects or areas even brighter than they
would be under good natural lighting. Although the
recorded image is not grainy, it may look as if it is strobing
due to the slow shutter speed.
NIGHT-ALIVE Button
Set the Power Switch to “ ” or “ ”. Press
1
2
REFRESH for approx. 1 second to select “VIDEO” (the
DSC Lamp goes out) or “DSC” (the DSC Lamp comes
on).
DSC Lamp
Press NIGHT-ALIVE repeatedly until the desired
mode’s name and indication appear.
They are displayed for approx. 2 seconds, then the
name disappears so that only the indication remains.
The mode is activated.
To cancel the effect, press NIGHT-ALIVE repeatedly
until “OFF” appears. “OFF” is displayed for approx.
2 seconds.
3
Power Switch
A NIGHT AUTO
The shutter speed is automatically adjusted
(maximum 1/6 sec.).
1 NIGHT 10X*
The shutter speed is set to 1/6th of a second to provide 10
times the sensitivity.
2 NIGHT 60X*
The shutter speed is set to 1 second to provide 60 times
the sensitivity.
*Appears when the Power Switch is set to “ ”.
NOTES:
● During Night-Alive, the following functions or settings
cannot be activated:
•“Picture Stabilizer” (੬ pg. 20), “Program AE With
Special Effects” (੬pg. 38) and “Digital Effects”
(੬ pg. 39).
•“S.LX” in CAMERA MENU (੬ pg. 41).
● Night-Alive does not work when LIGHT OFF/AUTO/
ON is set to “AUTO” or “ON” (੬ pg. 21).
● During Night-Alive, it may be difficult to bring the
camcorder into focus. To prevent this, use of a tripod is
recommended.
EN37
REFRESH Button
FADE/WIPE Button
Fade/Wipe Effects
These effects let you make pro-style scene transitions.
Fade- or wipe-in works at recording start, and fade- or
wipe-out works at recording end.
Set the Power Switch to “ ”. If the DSC Lamp is lit,
1
2
press REFRESH for approx. 1 second to select
DSC Lamp
“VIDEO”.
Press FADE/WIPE repeatedly until the desired mode’s
name and indication appear.
3
They are displayed for approx. 2 seconds, then the
name disappears so that only the indication remains.
The effect is reserved.
Press the Recording Start/Stop Button to activate fade-
in/out or wipe-in/out.
3
4
To cancel a fade or wipe, press FADE/WIPE
repeatedly until “OFF” appears.
“OFF” is displayed for approx. 2 seconds and the
fade/wipe standby mode is canceled.
Power Switch
Recording Start/Stop Button
FADER
Fades in/out to a black screen.
MOSAIC (Fader)
Gradually turns/returns the picture into/from a mosaic
pattern.
SHUTTER (Wipe)
A black screen moves in from the top and bottom, closing
over the image like a shutter, or a new image pushes open
the black screen vertically from the center.
SLIDE (Wipe)
A black screen moves in from the left to gradually cover
the image, or a new image moves in from right to left.
DOOR (Wipe)
Wipes in as the two halves of a black screen open to the
left and right, revealing the scene, or wipes out and the
black screen reappears from left and right to cover the
scene.
CORNER (Wipe)
Wipes in on a black screen from the upper right to the
lower left corner, revealing the scene, or wipes out from
lower left to upper right, leaving a black screen.
NOTE:
Pressing and holding the Recording Start/Stop
Button allows you to vary the length for the
image during fade in/out or wipe in/out.
WINDOW (Wipe)
Wipes in on a black screen from the center of the screen
towards the corners, revealing the scene, or wipe out from
the corners to the center, leaving a black screen.
ADVANCED FEATURES (cont.)
Program AE With Special Effects
38
EN
REFRESH Button
P.AE Button
Set the Power Switch to “ ”. Press REFRESH for
1
2
approx. 1 second to select “VIDEO” (the DSC Lamp
goes out) or “DSC” (the DSC Lamp comes on).
Press P.AE repeatedly until the desired mode’s name
and indication appear.
They are displayed for approx. 2 seconds, then the
name disappears so that only the indication remains.
The mode is activated.
DSC Lamp
To cancel the effect, press P.AE repeatedly until “OFF”
appears. “OFF” is displayed for approx. 2 seconds.
3
Power Switch
SPORTS
High shutter speed clearly captures fast-moving action.
ND : ND EFFECT
A black mist darkens the picture, as when an ND filter is
used. Helps to counter the effects of glare on the subject.
FG : FOG
Makes the picture look misty white, as when an external
fog filter is attached to the lens. Softens the image and
gives it a “fantasy” look.
NOTES:
● Only one mode can be engaged at a time.
● The screen becomes slightly dark in the High
Speed Shutter mode. Use in well-lit situations.
● In the “High Speed Shutter” or “Sports”
modes, picture color may be adversely
affected if the subject is lit by alternating
discharge-type light sources such as
TWILIGHT
Dusk, twilight scenery, fireworks, etc., look more natural
and dramatic. The following happens when Twilight
mode is selected:
•Auto gain control is turned off.
•White Balance is set to “
also be manually changed to another mode (੬ pg. 46).
•Auto Focus becomes available only in the range of
10 m (32 ft.) to infinity. To focus when the subject-to-
camera distance is less than 10 m (32 ft.), use manual
focusing (੬ pg. 45).
:FINE” (day mode), but can
flourescent or mercury-vapor lights.
● This function cannot be activated during
Night-Alive (੬ pg. 36).
● The “FOG” mode cannot be used when the
“VIDEO ECHO” mode (੬pg. 39) is activated.
S1/2000
(1/2000 sec. High Speed Shutter)
Captures faster action than Sports mode.
EN39
REFRESH Button
DIGIFECT Button
Digital Effects
Set the Power Switch to “ ”. Press REFRESH for
1
2
approx. 1 second to select “VIDEO” (the DSC Lamp
goes out) or “DSC” (the DSC Lamp comes on).
Press DIGIFECT repeatedly until the desired mode’s
name and indication appear.
They are displayed for approx. 2 seconds, then the
name disappears so that only the indication remains.
The mode is activated.
DSC Lamp
To cancel the effect, press DIGIFECT repeatedly until
“OFF” appears. “OFF” is displayed for approx.
2 seconds.
3
Power Switch
SEPIA
Recorded scenes have a brownish tint like old photos.
Combine this with the WIDE mode (੬ pg. 40, 41) for a
classic look.
MONOTONE
Like black and white films, your footage is shot in B/W.
Combine this with the WIDE mode (੬ pg. 40, 41) for a
classic look.
NEGA POSI
The colors of a picture are reversed.
MOSAIC
Turns recorded scenes into a mosaic pattern.
STRETCH
Doubles the width of the picture horizontally.
CLASSIC FILM
Makes your footage look like a classic movie by
shooting in black and white, with a strobing effect, and
black bars added at the top and bottom.
NOTES:
● Digital Effects can be changed during
recording or during Record-Standby.
● Digital zoom (੬pg. 20) cannot be used
when the “VIDEO ECHO” mode is activated.
● This function cannot be activated during the
Night-Alive (੬ pg. 36).
STROBE
Your recording looks like a series of consecutive
snapshots.
● Picture Stabilizer (੬ pg. 20) cannot be
activated during the “CLASSIC FILM”,
“STROBE” and “VIDEO ECHO” mode.
VIDEO ECHO
Adds a “ghost” to the subject, giving your recording a
“fantasy” feeling. Zoom magnification of over 10X is not
available.
ADVANCED FEATURES (cont.)
40
EN
REFRESH Button
Using Menus For Detailed Adjustment
This camcorder is equipped with an easy-to-use,
on-screen menu system that simplifies many of the more
detailed camcorder settings.
The operation system depends on the function you
DSC Lamp
1
wish to select.
Set the Power Switch to “ ”. Press REFRESH for
approx. 1 second to select “VIDEO” (the DSC Lamp
goes out) or “DSC” (the DSC Lamp comes on)
according to each function’s “*/**” explanation
described at the bottom of pages 41 and 42.
Press the MENU Wheel in. The Menu Screen
MENU Wheel
2
3
appears.
Rotate the MENU Wheel to select the desired
function.
•To go from CAMERA MENU to SYSTEM MENU,
rotate the MENU Wheel to select “ TO SYSTEM
MENU” and press it. SYSTEM MENU is composed
of 2 pages. To go to the next page, rotate the MENU
Wheel to select “ NEXT” and press it.
Power Switch
Display
CAMERA MENU
Menu Screen
ᮣ
TO SYSTEM MENU
•To return to CAMERA MENU from page 2 of
SYSTEM MENU, rotate the MENU Wheel to select
FOCUS
AUTO
EXPOSURE
AUTO
“
TO CAMERA MENU” and press it.
SYSTEM MENU
Press the MENU Wheel in to display the Setting
ᮣ
NEXT
4
5
6
Menu and rotate it to select the desired setting.
REC MODE
D. ZOOM
WI DE
SP
50
x
OFF
ON
Press the MENU Wheel in. The Menu Screen
reappears with the highlight bar on “ RETURN”.
–
S
VHS
TAPE LENGTH
D I SPLAY
P I CTURE
SNAPSHOT
T
30
FULL
F I NE
FULL
Press the MENU Wheel in. The normal screen
reappears.
ᮣ
RETURN
REC MODE
Setting Menu
(ex. REC MODE)
SP
EP
EX I T
SYSTEM MENU
ᮣ
NEXT
REC MODE
D. ZOOM
WI DE
EP
50
x
OFF
ON
–
S
VHS
TAPE LENGTH
D I SPLAY
P I CTURE
T
30
FULL
F I NE
FULL
SNAPSHOT
ᮣ
RETURN
Normal Screen
EN41
MENU SCREEN EXPLANATIONS
CAMERA MENU
Refer to “Focusing” (੬ pg. 45).
FOCUS
Refer to “Exposure Control” (੬ pg. 44).
EXPOSURE
M.W.B.
Refer to “White Balance Adjustment” and “Manual White Balance Operation”
(੬ pg. 46).
S.LX
MAX
To record a subject in a darkly lit environment, when it is more
convenient to shoot the subject with a brighter image even if the
picture becomes slightly coarse.
NORMAL
To record a subject in a dimly lit environment, when it is more
convenient to shoot with a less coarse picture although the
subject becomes slightly dark. This setting is suitable for
measuring sensitivity conforming to EIA-639 (EIA* Standard for
Low Light Sensitivity Measurement).
*EIA : Electronic Industries Alliance
OFF
Allows you to shoot dark scenes with no picture brightness
adjustment.
Allows you to superimpose one of eight preset titles (੬pg. 47).
TITLE*
Makes the date/time settings appear in the camcorder or on a connected monitor
(੬ pg. 47).
DATE/TIME
DISP.*
SYSTEM MENU
This Menu Screen cannot be accessed while recording.
Allows you to set the recording mode (SP or EP) depending on your preference
(੬ pg. 14).
REC MODE*
50X
Allows you to use the Digital Zoom. By digitally processing and
magnifying images, zooming is possible from 16X (the optical
zoom limit), to a maximum of 50X digital magnification.
D. ZOOM
600X
OFF
Allows you to use the Digital Zoom. By digitally processing and
magnifying images, zooming is possible from 16X (the optical
zoom limit), to a maximum of 600X digital magnification.
Digital Zoom is not available. Only optical zoom (maximum
16x magnification) can function. When set to “OFF” during
Digital Zoom, zoom magnification changes to 16X.
WIDE
OFF
ON
Does not display black bars.
Allows you to record black bars at the top and bottom of the screen
to produce a cinema-like “wide-screen” effect. If a snapshot
(੬pg. 28, 43) is taken while the camcorder is in the WIDE
mode, the snapshot image is recorded without the black bars at
the top and bottom of the screen.
*Activated only when “VIDEO” is selected (the DSC Lamp is not lit). If “DSC” is selected (the DSC Lamp is lit), this
function will not be activated even though the highlight bar on the Menu Screen will move to that position.
Functions listed without an asterisk are available when either “DSC” or “VIDEO” is selected.
: Factory-preset
CONTINUED ON NEXT PAGE
ADVANCED FEATURES (cont.)
42
EN
SYSTEM MENU (cont.)
ON
Records in S-VHS on a VHS or S-VHS cassette (੬ pg. 12).
Records in VHS on a VHS or S-VHS cassette (੬ pg. 12).
S-VHS***
(S-VHS ET***)
OFF
Allows you to set the tape length depending on the tape used (੬ pg. 14).
TAPE LENGTH*
DISPLAY
FULL
Make all of the indications appear on the LCD monitor/viewfinder
during playback or recording.
SIMPLE
Make the following indications disappear from the LCD monitor/
viewfinder during recording or playback: cassette warning, tape
remaining time, battery pack remaining power indicator and tape length
indicator (੬ pg. 62, 63)
Refer to “Picture Mode Setting” (੬ pg. 16).
PICTURE**
Displayed when “VIDEO” (the DSC Lamp is not lit, ੬ pg. 43) or “DSC”
(the DSC Lamp is lit, ੬ pg. 29) is selected.
SNAPSHOT
FULL
PIN-UP
MULTI-4
MULTI-9
Displayed when “DSC” (the DSC Lamp is lit, ੬ pg. 29) is selected.
Refer to “Animation” and “Time-Lapse” (੬ pg. 48).
REC TIME*
INT. TIME
Refer to “Time-Lapse” (੬ pg. 48).
Usually the distance to a subject where the lens is in focus depends on
the zoom magnification. Unless there is a distance of more than 1 m
(3.25 ft) to the subject, the lens is out of focus at the maximum telephoto
setting. When set to “ON”, you can shoot a subject as large as possible at
a distance of approx. 60 cm (23-5/8").
TELE MACRO
OFF
ON
•Depending on the zoom position, the lens may go out of focus.
Allows you to select the language (ENGLISH, FRENCH, SPANISH or PORTUGUESE)
of Instant Titles (੬ pg. 47).
TITLE LANG.*
DATE/TIME
Allows you to set the current date and time (੬ pg. 11).
ON
Demonstrates certain functions automatically. When “DEMO MODE” is
set to “ON” and the Menu Screen is closed, the demonstration starts.
Operating the Power Zoom Lever during the demonstration stops the
demonstration temporarily. If the Power Zoom Lever is not moved for
more than 1 minute after that, the demonstration will resume.
DEMO MODE*
NOTE:
When a tape whose Erase Protection tab is in the position that allows
recording is loaded in the camcorder, demonstration is not available.
OFF
Automatic demonstration will not take place.
*
Activated only when “VIDEO” is selected (the DSC Lamp is not lit). If “DSC” is selected (the DSC Lamp is lit), this
function will not be activated even though the highlight bar on the Menu Screen will move to that position.
** Activated only when “DSC” is selected (the DSC Lamp is lit). If “VIDEO” is selected (the DSC Lamp is not lit), this
function will not be activated even though the highlight bar on the Menu Screen will move to that position.
Functions listed without */** are available when either “DSC” or “VIDEO” is selected.
*** S-VHS ET is displayed when a VHS cassette is loaded, and S-VHS is displayed when an S-VHS cassette is loaded
(੬ pg. 12). If a cassette is not loaded, “S-VHS” will be displayed in the Menu Screen.
S-VHS ET is preset to “OFF”.
: Factory-preset
EN43
REFRESH Button
Snapshot
This interesting feature lets you record two types of digital
still images that look like photographs onto a tape, as well
as keeping them in the camcorder’s built-in memory. It is a
great way to spice up footage of events such as parties,
weddings and graduations.
DSC Lamp
SNAPSHOT Button
SNAPSHOT MODE SELECTION
Press in the tabs on the lens cap to remove it, then set
MENU
Wheel
1
the Power Switch to “ ”. The VIDEO Lamp comes on.
If the DSC Lamp is lit, press REFRESH for approx. 1
second to select “VIDEO”. The camcorder enters
Record-Standby mode.
Press the MENU Wheel in. The Menu Screen
2
3
4
appears.
Rotate the MENU Wheel to select “ TO SYSTEM
MENU” and press it to display SYSTEM MENU.
During shooting
Rotate the MENU Wheel to select “SNAPSHOT”, and
press it. The SNAPSHOT Menu appears.
Rotate the MENU Wheel to select “FULL” or “PIN-
UP”, and press it. Selection is complete.
Power Switch
Display
Menu Screen
TAPE LENGTH
T
30
The Menu Screen reappears with the highlight bar on
P I CTURE
STANDARD
FULL
5
“
RETURN”. Press the MENU Wheel in to close the
SNAPSHOT
Menu Screen.
ᮣ
RETURN
SNAPSHOT RECORDING
SNAPSHOT
SNAPSHOT Menu
FULL
Press SNAPSHOT.
–
P I N UP
1
•Regardless of the Power Switch position ( “ ” or
“
”), Snapshot recording takes place using the
selected Snapshot mode.
If you press during Record-Standby . . .
.... a still image will be recorded for approx.
6 seconds, then the camcorder re-enters the
Record-Standby mode.
EX I T
TAPE LENGTH
P I CTURE
SNAPSHOT
T
30
Menu Screen
If you press during Recording . . .
STANDARD
.... a still image will be recorded for approx.
6 seconds, then the normal recording resumes.
–
P I N UP
ᮣ
RETURN
NOTES:
● When the remaining number indicator displays “0”
(blinking), the still image will be recorded onto the tape
but not in the built-in memory. If you wish to store a still
image in the built-in memory, ੬ pg. 33.
● If a snapshot is taken while the camcorder is in the
WIDE mode (੬ pg. 41), the snapshot image is recorded
without the black bars at the top and bottom of the
screen.
● When a Snapshot is taken in a dark environment, the
still image recorded onto the tape and stored in memory
will become coarse and its true colors will be lost.
● The Snapshot mode can also be used during playback.
However, only the Full mode is available regardless of
the Snapshot mode setting, and the shutter sound is not
heard.
FULL
PIN-UP
(Pin-Up mode)
(Snapshot mode with
no frame)
ADVANCED FEATURES (cont.)
44
EN
REFRESH Button
Exposure Control
This feature automatically adjusts the iris for the best
available picture quality, but you can override it and make
the adjustment manually. Manual exposure adjustment is
recommended in the following situations:
•When shooting using reverse lighting or when the
background is too bright.
DSC Lamp
•When shooting on a reflective natural background such
as at the beach or when skiing.
•When the background is overly dark or the subject light.
Set the Power Switch to “ ”. Press REFRESH for
1
approx. 1 second to select “VIDEO” (the DSC Lamp
goes out) or “DSC” (the DSC Lamp comes on).
MENU Wheel
Press the MENU Wheel in. The Menu Screen
2
3
4
appears.
Rotate the MENU Wheel to select “EXPOSURE” and
press it. The EXPOSURE Menu appears.
Power Switch
Rotate the MENU Wheel to select “MANU”, then
press it. The Menu Screen disappears and “00”
(exposure control level counter) appears.
Manual Exposure
Screen
00
To brighten the image, rotate the MENU Wheel
downward. The exposure control level counter
increases (maximum +06).
To darken the image, rotate the MENU Wheel
upward. The exposure control level counter
decreases (maximum –06).
5
Exposure
control
level counter
Press the MENU Wheel in. The setting is complete.
To brighten the image
6
7
The Menu Screen reappears with the highlight bar on
“
RETURN”.
+
–06
06
Press the MENU Wheel in. The Menu Screen
disappears and the exposure control level counter
reappears to indicate the exposure is adjusted.
NOTES:
To darken the image
● To return to the factory setting, select “AUTO” in step 4.
● To re-adjust exposure, repeat the procedure from step 2.
EN45
Focus detection zone
Focusing
AUTO FOCUS
The camcorder’s Full Range AF system offers continuous
shooting ability from close-up to infinity. However, correct
focus may not be obtainable in the situations listed below
(in these cases use manual focusing):
•When two subjects overlap in the same scene.
•When illumination is low.*
•When the subject has no contrast (difference in
brightness and darkness), such as a flat, one-color wall,
or a clear, blue sky.*
•When a dark object is barely visible in the viewfinder.*
•When the scene contains minute patterns or identical
patterns that are regularly repeated.
•When the scene is affected by sunbeams or light
reflecting off the surface of a body of water.
•When shooting a scene with a high-contrast background.
NOTES:
● If the lens is smeared or blurred, accurate
focusing is not possible. Keep the lens clean,
wiping with a piece of soft cloth if it gets
dirty. When condensation occurs, wipe with
a soft cloth or wait for it to dry naturally.
● When shooting a subject close to the lens,
zoom out first (੬pg. 20). If zoomed in in
the auto focus mode, the camcorder could
automatically zoom out depending on the
distance between the camcorder and the
subject. This does not occur with “TELE
MACRO” (੬pg. 42).
* The low-contrast warning “
” appears.
MANUAL FOCUS
Make the necessary viewfinder adjustments to use the
viewfinder (੬ pg. 10).
REFRESH Button
Set the Power Switch to “ ”. Press REFRESH for
1
approx. 1 second to select “VIDEO” (the DSC Lamp
goes out) or “DSC” (the DSC Lamp comes on).
DSC Lamp
Press the MENU Wheel in. The Menu Screen
2
3
4
appears.
Rotate the MENU Wheel to select “FOCUS” and
press it. The FOCUS Menu appears.
Rotate the MENU Wheel to select “MANU”, then
press it. The Menu Screen disappears and “ ” and
MENU Wheel
Power Switch
“
” appear. The focus is locked at this point.
To focus on a farther subject, rotate the MENU Wheel
upward. “ ” appears and blinks.
To focus on a nearer subject, rotate the MENU Wheel
downward. “ ” appears and blinks.
5
Press the MENU Wheel in. The setting is complete.
6
7
The Menu Screen reappears with the highlight bar on
“
RETURN”.
Press the MENU Wheel in. The Menu Screen
disappears and “
is locked.
” reappears to indicate the focus
NOTES:
● To return to Auto Focus, select “AUTO” in step 4.
● To re-adjust Manual Focus, repeat the procedure from step 2.
● Be sure to focus the lens in the maximum telephoto position when you use the Manual Focus mode. If you
focus in on a certain subject in the wide-angle position, sharply focused images cannot be obtained when
zoomed in because the depth-of-field is reduced at longer focal lengths.
● When the focus level cannot be adjusted any farther or closer, “ ” or “ ” will blink.
ADVANCED FEATURES (cont.)
46
EN
White Balance Adjustment
Manual White Balance Operation
A term that refers to the correctness of color
reproduction under various lighting. If the white
balance is correct, all other colors will be accurately
reproduced.
The white balance is usually adjusted automatically.
However, more advanced camcorder operators
control this function manually to achieve a more
professional color/tint reproduction.
Perform Manual White Balance when shooting under
various types of lighting.
Follow steps 1 through 4 of the white balance
1
2
adjustment, and select “MWB”.
Hold a sheet of plain white paper in front of the
subject. Adjust zoom or position yourself so that
the white paper fills the screen.
Set the Power Switch to “ ”. Press REFRESH
Press the MENU Wheel in until “MWB” begins
blinking.
When the setting is completed, “MWB” stops
blinking, and the Menu Screen reappears with
the highlight bar on “ RETURN”.
1
for approx. 1 second to select “VIDEO” (the
DSC Lamp goes out) or “DSC” (the DSC Lamp
comes on).
3
Press the MENU Wheel in. The Menu Screen
2
3
4
appears.
Press the MENU Wheel in again to close the
4
Menu Screen.
Rotate the MENU Wheel to select “M.W.B.”,
then press it. The M.W.B. Menu appears.
REFRESH Button
Rotate the MENU Wheel to select the desired
setting.
“AUTO”
White balance is adjusted automatically (factory
preset).
DSC Lamp
“
: FINE”
Outdoors on a sunny day.
: CLOUD”
Outdoors on a cloudy day.
: HALOGEN”
MENU Wheel
“
White paper
“
A video light or similar type of lighting is used.
“MWB”
White balance is set manually.
Press the MENU Wheel in. The Menu Screen
Power Switch
5
reappears with the highlight bar on
“
RETURN”. Press the MENU Wheel in again
to close the Menu Screen.
To Change The Tint For Recording . . .
.... in step 2, substitute colored paper for white. The
white balance is adjusted based on the color,
changing the tint. Red paper = deeper green; blue
paper = orange; yellow paper = deeper purple.
To Return To Automatic White Balance . . .
.... select “AUTO” in step 4. Or set the Power
Switch to “ ”.
NOTE:
NOTES:
White balance cannot be used when the “SEPIA” or
“MONOTONE” mode (੬ pg. 39) is activated.
● In step 2, it may be difficult to focus on the white
paper. In such a case, adjust focus manually
(੬pg. 45).
● A subject can be shot under various types of lighting
conditions indoors (natural, flourescent, candlelight,
etc.). Because the color temperature is different
depending on the light source, the subject tint will
differ depending on the white balance settings. Use
this function for a more natural result.
● Once you adjust white balance manually, the
setting is retained even if the power is turned off or
the battery removed.
EN47
Date/Time Insert
Set the Power Switch to “ ”. If the DSC Lamp is lit,
1
press REFRESH for approx. 1 second to select
Allows you to display the date and time in the
camcorder or on a connected color monitor, as
well as to record them manually or
automatically.
“VIDEO”.
Press the MENU Wheel in. The Menu Screen
2
3
4
5
appears.
You should have already performed the Date/
Time Setting procedure (੬pg. 11).
Rotate the MENU Wheel to select “DATE/TIME DISP.”
and press it. The DATE/TIME DISP. Menu appears.
REFRESH Button
Rotate the MENU Wheel to select the desired mode,
then press it. The desired mode is activated.
The Menu Screen reappears with the highlight bar on
“
RETURN”. Press the MENU Wheel in to close the
DSC Lamp
Menu Screen.
NOTES:
DISPLAY
● The selected display can be recorded.
● If you do not want to record the display, select the OFF
mode before shooting.
● The date/time is displayed during the VIDEO mode only,
and it is recorded only onto the tape.
MENU Wheel
Power Switch
AUTO DATE
● Your camcorder automatically records the date for about
5 seconds after recording is initiated in the following
situations:
DEC 25. 01
•After changing the date.
AUTO DATE
•After loading a cassette.
•After Auto Date Record mode is selected by rotating
the MENU Wheel.
● In this mode, the date is replaced after 5 seconds with
“AUTO DATE” but this is not recorded.
DEC 25. 01
(DATE)
AM 10 : 25 : 00
(TIME)
DEC 25. 01
AM 10 : 25 : 00
(DATE/TIME)
Set the Power Switch to “ ”. If the DSC Lamp is lit,
No indication
(OFF)
1
press REFRESH for approx. 1 second to select
“VIDEO”.
Press the MENU Wheel in. The Menu Screen
Instant Titles
2
3
4
5
appears.
The camcorder has eight preset titles in
memory. You can superimpose one of them
over the video image.
Rotate the MENU Wheel to select “TITLE” and press it.
The TITLE Menu appears.
Instant Titles can be displayed not only in
English but also in French, Spanish and
Portuguese. Change the setting in TITLE LANG.
in SYSTEM MENU (੬ pg. 42).
Rotate the MENU Wheel to select the desired mode,
then press it. The desired mode is activated.
The Menu Screen reappears with the highlight bar on
T I TLE
OFF
“
RETURN”. Press the MENU Wheel in to close the
HAPPY B I RTHDAY
OUR VACAT I ON
MERRY CHR I STMAS
Menu Screen.
NOTES:
A
SPEC I AL DAY
● The title is displayed during the VIDEO mode only, and
it is recorded only onto the tape.
● The selected title will remain until OFF is selected in the
TITLE Menu.
HAPPY HOL I DAYS
OUR NEW BABY
WEDD I NG DAY
CONGRATULAT I ONS
EX I T
ADVANCED FEATURES (cont.)
48
EN
NOTE:
Animation
Before performing the following steps, make
sure that:
You can shoot a series of pictures, each slightly different,
of the same object for a brief period of time.
● “VIDEO” is selected (the DSC Lamp is not lit).
● The Power Switch is set to “ ”.
● The camcorder is in the Record-Standby
mode.
Press the MENU Wheel in. The Menu Screen
1
2
appears.
● The recording mode is set to “SP”.
Rotate the MENU Wheel to select “ TO SYSTEM
MENU” and press it to display SYSTEM MENU.
Rotate the MENU Wheel to select “ NEXT” and
press it to display the next page. Then, rotate the
MENU Wheel to select “REC TIME” and press it. The
REC TIME Menu appears. Rotate the MENU Wheel to
select the desired recording time, then press it.
The Menu Screen reappears with the highlight bar on
MENU Wheel
3
4
”
RETURN”. Press the MENU Wheel in again to
close the Menu Screen.
Press the Recording Start/Stop Button after focusing
on the subject. The recording stops automatically
after the selected period of time.
Recording Start/Stop Button
Display
•Repeat step 4 for the desired number of pictures.
To release the Animation mode, set “REC TIME” in
REC T I ME
5
the Menu screen to “OFF”.
REC TIME Menu
OFF
1
1
1
5
/
/
4
2
S
S
S
S
Time-Lapse
You can record sequentially at preset time spans. Leaving
the camcorder aimed at a specific subject, you can record
subtle changes over an extended period of time.
I NT. T I ME
INT. TIME Menu
OFF
15
30
S
S
Set “REC TIME” (੬step 1 and 2 of “Animation”
above).
1
5
M I N
M I N
1
2
Rotate the MENU Wheel to select “INT. TIME” and
press it. The INT. TIME Menu appears. Rotate the
MENU Wheel to select the desired interval time, then
press it. The Menu Screen reappears with the
highlight bar on “ RETURN”. Press the MENU
Wheel in again to close the Menu Screen.
Interval time
indicator
15
S
1
S
Recording time
indicator
Press the Recording Start/Stop Button. Recording and
intervals alternate automatically.
3
4
To release the Time-Lapse mode, when “
displayed, press the Recording Start/Stop Button to
display “ ”, then set “REC TIME” and
“INT. TIME” in the Menu Screen to “OFF”.
” is not
NOTES (for Animation and Time-Lapse):
● For best results, make sure the camcorder is secured when shooting in Animation or Time-Lapse mode.
● Fade- or wipe-in/out cannot be performed during Animation or Time-Lapse shooting.
● Before performing other operations following Animation or Time-Lapse recording, make sure the Animation
or Time-Lapse mode is deactivated.
● Animation and Time-Lapse are canceled when the power is shut off or when the cassette is ejected.
USING THE REMOTE CONTROL UNIT
EN49
The Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic
operations (Playback, Stop, Pause, Fast-Forward and Rewind) of your VCR.
1
2
3
4
5
6
8
9
0
!
@
7
Functions
Buttons
With the camcorder’s Power Switch set
to “ ” or “ ”.
With the camcorder’s Power Switch
set to “
”.
1 Infrared beam
Transmits the beam signal.
transmitting window
2 ZOOM (T/W) Buttons Zoom in/out (੬ pg. 20)
Zoom in/out (੬ pg. 51)
3 PLAY Button
—
Playback start (੬ pg. 22)
4 REW Button
Retake (rewind), Quick Review
(੬ pg. 21, 29)
Rewind, Reverse Shuttle Search,
Previous Still Image Playback
(੬ pg. 22, 30)
5 STOP Button
—
Stop (੬ pg. 22)
6 INSERT Button
—
Insert Editing (੬ pg. 52, 53)
7 REC TIME Button
Animation, Time-Lapse (੬ pg. 51)
—
ANIM. Button
8 START/STOP Button
Functions the same as the Recording Start/Stop Button on the camcorder.
9 FF Button
Retake (forward) (੬ pg. 21)
Fast-Forward, Forward Shuttle Search,
Next Still Image Playback (੬ pg. 22,
30)
0 PAUSE Button
—
—
Pause (੬ pg. 22)
Audio dubbing (੬ pg. 53)
—
! A.DUB Button
@ INT. TIME Button
Time-Lapse (੬ pg. 51)
SELF TIMER Button*
*This function is unavailable with this camcorder.
USING THE REMOTE CONTROL UNIT (cont.)
50
EN
Installing The Batteries
The remote control uses two “AAA (R03)” size
batteries. See “General Battery Precautions”
(੬ pg. 66).
1
3
Open the battery compartment cover as
1
2
3
illustrated.
2
Insert two “AAA (R03)” size batteries in the
correct direction.
Replace the battery compartment cover.
Remote sensor
When using the remote control, be sure to point it
at the remote sensor. The illustration shows the
approximate transmitted beam effective area for
indoor use.
The transmitted beam may not be effective or may
cause incorrect operation outdoors or when the
remote sensor is directly exposed to sunlight or
powerful lighting.
Transmitted beam
effective area
5m (16 ft)
EN51
To magnify the recorded image up to 10X at any time
during playback.
Remote sensor
Playback Zoom
NOTES:
● Use the remote control unit to perform this procedure.
● Make sure that the TBC mode is activated (੬ pg. 23).
1) Press PLAY to find the scene of interest.
2) Press the ZOOM Buttons (T/W) on the remote control.
Make sure the remote control is pointed at the
camcorder’s remote sensor. Pressing T zooms in.
To End Zoom . . .
.... press and hold W until magnification returns to
normal. Or, press STOP and then press PLAY.
ZOOM (T/W)
NOTES:
● Zoom can also be used during still playback.
● Due to digital image processing, the quality of the image
may suffer.
PLAY
STOP
● After zooming in on a still video image, when normal
playback is started, the zoomed-in effect is momentarily
canceled but then resumes, returning magnification to
the previously set level.
Display
Animation And Time-Lapse
The remote control lets you set/release Interval Time and
Recording Time without using the Menu Screen.
Interval time
indicator
Animation
1) Set
1
1
M I N
/
2S
Instead of performing steps 1 and 2 on pg. 48
(“Animation”), press REC TIME on the remote control.
Each time REC TIME is pressed, the Recording Time
indicator appears, changing in the following order:
1/4S, 1/2S, 1S, 5S and no indication (off).
2) Release
Recording time
indicator
Remote sensor
Instead of using the Menu in step 5 on pg. 48
(“Animation”), press REC TIME on the remote control
until the Recording Time indicator disappears.
Time-Lapse
1) Set
Instead of performing steps 1 and 2 on pg. 48 (“Time-
Lapse”), press REC TIME and INT. TIME on the remote
control. Each time REC TIME is pressed, the Recording
Time indicator appears, changing in the following
order: 1/4S, 1/2S, 1S, 5S and no indication (off). Each
time INT. TIME is pressed, the Interval Time indicator
appears, changing in the following order: 15S, 30S,
1MIN, 5MIN and no indication (off).
2) Release
START/STOP
Instead of using the Menu in step 4 on pg. 48 (“Time-
Lapse”), press REC TIME and INT. TIME on the remote
control until the indicators disappear.
NOTE:
Also refer to pg. 48.
REC TIME
INT. TIME
USING THE REMOTE CONTROL UNIT (cont.)
52
EN
REFRESH Button
Insert Editing (VIDEO)
COUNTER R/M Button
You can record a new scene onto a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in- and out-points. The
original audio remains unchanged.
NOTE:
Use the remote control unit to perform this procedure.
DSC Lamp
Set the Power Switch to “
”. If the DSC Lamp is
1
lit, press REFRESH for approx. 1 second to select
“VIDEO”.
Play back the tape, locate the Edit-Out point and
2
3
press PAUSE.
Press and hold COUNTER R/M on the camcorder for
more than 1 second to reset the tape counter, then
press it again for less than 1 second so that “M”
appears.
Power Switch
Display
Press REW to go a little beyond the beginning of the
scene you want to replace, press PLAY to view the
recorded tape, and press PAUSE exactly at the Edit-In
point where the new scene should start.
w
4
5
Insert editing
indicator
–
:
:
M
0
12 34
Tape Counter
Press and hold INSERT, and without releasing
INSERT, press and release PAUSE on the Remote
Control. The Insert Editing indicator appears and the
Insert Editing mode is engaged. When the scene the
camcorder is aimed at appears on the screen, go to
the next step.
e
4
Audio dubbing
indicator
–
:
:
M
0
0 5 2 0
During Audio
Dubbing
To begin Insert Editing, press START/STOP. When the
counter reaches “0:00:00”, editing stops automati-
cally and the camcorder enters the Insert-Pause
mode.
6
7
Remote sensor
To end Insert Editing, press STOP.
NOTES:
● During Insert Editing, the original audio will be heard
from the speaker.
● After step 5, Retake (੬ pg. 21) can be performed.
● The tape may stop slightly before or after the designated
end point, and noise bars may appear. Neither indicates
a defect in the unit.
● Only the video signal is recorded in the Insert Editing
mode.
Microphone
START/STOP
PLAY
REW
STOP
FF
PAUSE
A.DUB
INSERT
EN53
NOTE:
Use the remote control unit to perform the following procedures.
Insert Editing (Insert A Still Image
From The Built-in Memory Onto A
Tape)
Audio Dubbing
You can record a new soundtrack on a prerecorded
tape (normal audio only). The sound is recorded from
the built-in microphone.
Perform steps 1, 2 and 3 of the Insert Editing
(VIDEO) procedure (੬ pg. 52) before continuing.
You can insert a still image stored in the camcorder’s
built-in memory into a previously recorded tape,
replacing a section of the original recording with
minimal picture distortion at the in- and out-points.
The original audio remains unchanged.
Press REW to go a little beyond the beginning of
1
the scene onto which you want to dub the new
audio, press PLAY to view the recorded tape,
then press PAUSE at exactly the point where
dubbing should start.
Perform steps 1 through 5 in Insert Editing (VIDEO)
(੬pg. 52) before the following procedure.
Press REFRESH for approx. 1 second to select
Press and hold A. DUB, and without releasing
A. DUB, press and release PAUSE on the
Remote Control. The Audio Dub-Standby mode
is engaged.
1
2
“DSC”. The DSC Lamp comes on. Press REW
2
3
4
or FF to select the still image you wish to insert.
To begin Insert Editing, press START/STOP.
When the counter reaches “0:00:00”, editing
stops automatically and the camcorder enters
the Insert-Pause mode.
To insert still images in sequential order onto
the tape . . .
... press REW or FF to move the page forward.
To insert still images at random onto the
tape . . .
... first record the still image you selected in
step 1 onto the tape, then press START/
STOP to engage the Insert-Pause mode. To
select another still image, press REW or FF
again, then press START/STOP. Insert Editing
begins.
To begin Audio Dubbing, press PLAY. When the
counter reaches “0:00:00”, Audio Dubbing
stops automatically and the camcorder enters
the Audio Dub-Standby mode.
To end Audio Dubbing, press STOP.
NOTES:
● Do not press FF or REW during Audio Dub-
Standby, or the edit points will not be accurate.
● If the microphone is too close to the TV, or if the
TV’s volume is too high, whistling or howling may
occur.
To end Insert Editing, press STOP.
NOTES
3
(for Insert Editing and Audio Dubbing):
● Insert Editing and Audio Dubbing may not work
correctly if the tape contains blank segments, or if
the recording speed was changed during the
original recording.
NOTES:
● The tape may stop slightly before or after the
designated end point, and noise bars may appear.
Neither indicates a defect in the unit.
● Only video signal is recorded in the Insert Editing
mode.
● To edit/dub onto a tape, make sure the Erase
Protection tab is in the position that allows
recording. If not, slide the tab. Some cassettes have
removable tabs. If the tab has been removed, cover
the hole with adhesive tape.
● Do not press STOP during Insert Editing or Audio
Dubbing, or the edit points will not be accurate.
● During Insert Editing and Audio Dubbing, when
Insert-Pause or Audio Dub-Standby is engaged, the
counter may go slightly past “0:00:00”. Recording,
however, stops at exactly 0:00:00.
REFERENCES
REFERENCES
54
EN
CONTENTS
TROUBLESHOOTING ....................... 55–57
DETAILS ..................................... 58–59
INDEX ....................................... 60–63
Controls, Connectors And Indicators ........60 – 61
Indications ....................................62 – 63
TERMS ...................................... 64–65
CAUTIONS .................................. 66–68
SPECIFICATIONS.................................... 69
TROUBLESHOOTING
If, after following the steps in the chart below, the problem still exists, please consult your JVC dealer.
EN55
The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might
prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Adapter,
etc.); and then re-connect it and proceed as usual from the beginning.
SYMPTOM
POSSIBLE CAUSE(S)
POWER
No power is supplied.
● The battery pack has not been attached correctly (੬ pg. 8).
● The battery pack is not charged (੬ pg. 8).
● The power supply has not been correctly connected (੬ pg. 9).
The power suddenly goes off and does
not come back on by itself.
● The battery pack has completely discharged.
● Remove the cassette and disconnect the power source, then
after a few minutes, try turning the power back on. If it still
does not come on, consult your nearest JVC dealer.
OTHER
Some functions are not available.
● The Power Switch is set to “ ”.
● Certain combinations of modes or effects are not possible to use.
During recording, the indications do
not appear.
● Set “DISPLAY” to “FULL” in SYSTEM MENU (੬pg. 42).
Vertical white lines appear when
shooting a very bright object.
● This sometimes occurs when the contrast between the back-
ground and the object is great. It is not a defect of the camcorder.
Bright, crystal-shaped spots appear in
the LCD monitor and the viewfinder.
● Sunlight is directly entering the lens. This is not a defect of the
camcorder.
The rear of the LCD monitor is hot.
● The light used to illuminate the LCD monitor causes it to be
hot. Close the LCD monitor to turn it off or set the Power
Switch to “OFF”, and let the unit cool down.
● The LCD monitor and the viewfinder are made with high-
precision technology. However, black spots or bright spots of
light (red, green or blue) may appear constantly on the LCD
monitor or in the viewfinder. These spots are not recorded on
the tape. This is not due to any defect of the unit. (Effective
dots: more than 99.99 %.)
Colored bright spots appear all over the
LCD monitor or the viewfinder.
The indicators and the picture color on
the LCD monitor are not clear.
● This may occur when the surface or the edge of the LCD
monitor is pressed.
The LCD monitor, the viewfinder and
the lens have become dirty (ex.
fingerprints).
● Wipe them gently with soft cloth. Gently wipe the LCD monitor
in a semicircle because wiping strongly spreads the stain and it
won’t come out easily.
An error number (i.e. E03) appears.
● Turn the camcorder’s power off, then disconnect the power
source. After a few minutes, try turning the power on again. If
the error number still appears, consult your nearest JVC dealer.
The image is out of focus.
● The diopter needs to be adjusted (੬ pg. 10).
● The scene being shot is adversely affecting the operation of
Auto Focus (੬pg. 45).
Even though the lens cap is detached,
the “LENS CAP” warning indicator
(੬ pg. 63) blinks.
● The “LENS CAP” warning indicator may blink when the
camcorder is used in dark areas, regardless of whether the lens
cap is attached or detached.
TROUBLESHOOTING (cont.)
When “VIDEO” is selected (the DSC Lamp is not lit):
56
EN
SYMPTOM
POSSIBLE CAUSE(S)
RECORDING
Recording cannot be performed.
● Make sure the Erase Protection tab is in the position that allows
recording. If not, slide the tab. Some cassettes have removable
tabs. If the tab has been removed, cover the hole with adhesive
tape (੬ pg. 15).
● If “DSC” is selected (the DSC Lamp is lit), it is not possible to
record onto the tape. Press REFRESH for approx. 1 second to
select “VIDEO” (the DSC Lamp is not lit).
Recording does not start.
● The camcorder Power Switch has not been set to “ “ or “
(੬ pg. 18).
”
Animation or Time-Lapse is not
available.
● Before recording in the Animation mode at the very beginning
of a tape, set the camcorder to the Recording mode for about
5 seconds, so that the tape runs smoothly. Using the Fade-in
function at this point is a good way to begin an animated
program (੬ pg. 48).
PLAYBACK
The tape is running, but there is no
playback picture.
● The TV has not been set to its VIDEO mode or channel.
● If A/V connection is used, the TV’s VIDEO/TV Switch has not
been set to VIDEO.
Playback cannot be performed.
● If “DSC” is selected (the DSC Lamp is lit), it is not possible to
play back a tape. Press REFRESH for approx. 1 second to select
“VIDEO” (the DSC Lamp is not lit).
Playback picture is blurred or
interrupted.
● The video heads are dirty or worn out. Consult your nearest
JVC dealer for head cleaning or replacement.
The counter indication is blurred during
Still playback.
● This is normal.
TAPE TRANSPORT
The tape stops during fast-forward or
rewind.
● The Counter Memory Function has been activated (੬ pg. 23).
Rewinding or fast-forwarding cannot be
performed.
● The tape is already fully wound on one reel or the other.
OTHER
The picture is blurred in the Quick
Review or Retake mode.
● This is normal while recording in the EP mode. Some noise
may be present while recording in the SP mode (੬pg. 14).
The date and time displays
disappear.
● If you remove the power source from the camcorder while the
power is on, all settings and selections are erased. Make sure to
turn the camcorder’s power off before disconnecting the power
source.
The wrong date and time are displayed/
recorded.
● If you have not performed Date/Time Setting (੬ pg. 11), the
date and time are not displayed/recorded correctly. Be sure that
Date/Time setting is carried out.
The tape will not eject.
● The battery pack is running low.
● If the LCD monitor is not open over 60 degrees, EJECT switch
does not function.
EN57
When “DSC” is selected (the DSC Lamp is lit):
SYMPTOM
POSSIBLE CAUSE(S)
SHOOTING
Although SNAPSHOT is pressed, a still
image is not stored in the built-in
memory.
● When the number of remaining shots available reaches “0”
(blinking), it becomes impossible to take your next shot.
Perform “Deleting Images” function to remove some still
images already stored in memory (੬ pg. 33).
It is not possible to shoot in sucession.
● A still image is in the process of being stored in memory for
approx. 2 seconds after SNAPSHOT is pressed. During that
time, it is impossible to take another shot. When the still image
disappears and the scene you are currently aimed at appears
on the screen, take another shot (੬ pg. 28).
PLAYBACK
Although “ALL” is selected in the
DELETE Menu Screen, all still images
cannot be deleted.
● The “Protecting Images” function is in effect for some still
images. If they are not necessary, cancel the “Protecting Images”
function, then try deleting all still images again (੬ pg. 32).
OTHER
Date/Time Insert is not performed
while shooting a still image.
● It is not possible to display the date/time on a still image.
Instant Titles are not displayed while
shooting a still image.
● It is not possible to display the Instant Titles on a still image.
Some settings cannot be changed in the
Menu Screen.
● It is not possible to set “REC TIME” and “INT. TIME” in the
Menu Screen.
Since the camcorder is a microcomputer-controlled device, external noise and interference (from a TV, a
radio, etc.) might prevent it from functioning properly. For example, when a still image you shot is stored
in the camcorder’s built-in memory, the above may cause the following: Although the remaining number
of shots indicator shows that shooting is possible, a still image cannot be stored in memory after shooting.
In such a case, initialize the memory by following steps 1 through 3 below. Please note that initialization
deletes all the still images (including ones for which you performed the “Protect” function) stored in the
camcorder’s memory. If you wish to keep any of the still images that are stored in memory, before
initialization first transfer them to a PC and save them. If image data is corrupt, transfer is impossible.
1. Set the Power Switch to “
”. If the DSC Lamp is not lit, press REFRESH
FORMAT
for approx. 1 second to select “DSC”.
CANCEL
ENTER
2. Press P.AE for more than 5 seconds. The FORMAT Menu appears.
3. Rotate the MENU Wheel to select “CANCEL” or “ENTER” , then press it.
•“CANCEL” does not initialize the memory.
•“ENTER” initializes the memory. During initialization, “ENTER” blinks.
When initialization is complete, the screen becomes blue back.
FORMAT Menu
CAUTION:
While “ENTER” is selected and it is blinking, switching off the camcorder or removing the power supply
unit (battery pack or AC Adapter) may cause the camcorder’s built-in memory to become corrupt.
Never remove the power supply unit at this stage.
DETAILS
58
EN
I T E M S
N O T E S
❍ Perform charging where the temperature is between 10°C and 35°C
(50°F and 95°F). 20°C to 25°C (68°F to 77°F) is the ideal
temperature range for charging. If the environment is too cold,
charging may be incomplete.
❍ Power
(੬ pg. 8)
❍ Charging times are for a fully discharged battery pack.
❍ Charging time varies according to the ambient temperature and the
status of the battery pack.
❍ To avoid interference with reception, do not use the AC Adapter
near a radio.
❍ Since the AC Adapter processes electricity internally, it becomes
warm during use. Be sure to use it only in well-ventilated areas.
❍ The following operation stops charging or discharging:
•Set the Power Switch to “
”, “ ” or “ ”.
•Disconnect the AC Adapter from the camcorder.
•Unplug the AC Adapter’s power cord from the AC outlet.
•Detach the battery from the camcorder.
❍ Date/Time
Settings
❍ The date/time cannot be stored in memory if the built-in clock
battery runs out. Consult an authorized JVC dealer for replacement,
or set the date/time as necessary before you start shooting.
(੬ pg. 11)
EN59
I T E M S
N O T E S
❍ When the Power Switch is set to “ ” or “ ” and the LCD
❍ VIDEO
monitor is opened at an angle of 60 degrees or more, the LCD
monitor switches on and the viewfinder switches off automatically
to save power.
RECORDING
(੬ pg. 18, 19)
❍ The cassette holder cannot be opened unless a power supply is
attached.
❍ There may be a delay after you slide EJECT until the cassette holder
opens. Do not use force.
❍ The time required to calculate the remaining tape length, and the
accuracy of the calculation, may vary according to the type of tape
used.
❍ The tape remaining time indicator is correct only if the correct tape
length has been selected (੬ pg. 14).
❍ “TAPE END” appears when the tape reaches its end, and the power
goes off automatically if left in this condition for 5 minutes.
“TAPE END” also appears when a cassette whose tape is already at
its end is loaded.
❍ If the Recording Start/Stop button is pressed after the Record-
Standby mode has continued for over 5 minutes, recording may not
start immediately.
❍ While shooting, sound is not heard from the speaker.
❍ The “TBC” indicator turns green (gray with a camcorder equipped
❍ TBC
with a black/white viewfinder) while TBC is working.
(Time Base
Corrector)
(੬ pg. 23)
❍ TBC does not work during still playback and shuttle search.
❍ The “TBC” indicator turns white while TBC is not operative.
❍ It may take a few seconds before TBC actually starts working.
❍ The picture may be distorted if the TBC mode is activated or
deactivated at the edit-in/-out points or when normal playback
resumes after still playback or shuttle search.
❍ If the playback picture is distorted when TBC is set to on, turn off
TBC.
INDEX Controls, Connectors And Indicators
60
EN
p
#
$
%
^
Q
q
y u
1
2
3
4
5
w
e
6 7 8 9 0 !
r
t
(
*
&
o
i
W
)
@
E
R
T
I
Y
U
EN61
Controls
Connectors
1 Video Light Switch
The connectors q to r are located beneath the
cover.
[LIGHT OFF/AUTO/ON] ..................... ੬pg. 21
2 Stop Button [STOP] ........................ ੬pg. 22, 29
q S-Video Output Connector [S] .............. ੬ pg. 24
w Audio Output Connector [A] ................ ੬ pg. 24
e Video Output Connector [V] ................ ੬ pg. 24
r DC IN Connector............................... ੬ pg. 8, 9
t Digital Connector [DIGITAL] ................ ੬ pg. 34
3 •Retake Rewind Button [RETAKE R]..... ੬pg. 21
•Quick Review Button [
R] ...... ੬pg. 21, 29
•Rewind Button [R]............................. ੬pg. 22
•Previous Page Button......................... ੬pg. 30
4 Play/Pause Button .......................... ੬pg. 22, 29
5 •Retake Forward Button [RETAKE F] .... ੬pg. 21
•Fast-Forward Button [F] ..................... ੬pg. 22
•Next Page Button .............................. ੬pg. 30
Indicators
y •DSC Lamp ...................... ੬ pg. 18, 22, 28, 30
•CHARGE Lamp ................................... ੬pg. 8
6 •Fade/Wipe Button [FADE/WIPE] ........ ੬pg. 37
•Counter Reset/Memory Button
u •VIDEO Lamp .................................... ੬ pg. 18
•REFRESH Lamp ................................... ੬pg. 8
[COUNTER R/M] .............................. ੬pg. 23
7 •Program AE Button [P.AE] .................. ੬pg. 38
Other Parts
•Memory Initialize Button ................... ੬pg. 57
i LCD Monitor ................................. ੬ pg. 18, 19
o Shoulder Strap Eyelets .......................... ੬ pg. 10
p Eyepiece
Q Battery Pack Mount ............................... ੬pg. 8
W Viewfinder ........................................... ੬ pg. 10
E Speaker ............................................... ੬ pg. 22
8 Digital Effect Button [DIGIFECT] .......... ੬pg. 39
9 NIGHT-ALIVE Button .......................... ੬pg. 36
0 REFRESH Button .............੬ pg. 8, 18, 22, 28, 30
! EJECT Switch ....................................... ੬pg. 15
@ Close Button ........................................ ੬pg. 15
# •MENU Wheel [–, +] .......................... ੬pg. 40
•BRIGHT Wheel [–, +] ........... ੬pg. 18, 22, 30
•TRACKING Wheel [–, +] ................... ੬pg. 23
R •Camera sensor
Be careful not to cover this area; a sensor
necessary for shooting is built-in here.
•Remote Sensor .................................. ੬ pg. 50
$ Snapshot Button [SNAPSHOT] ....... ੬pg. 28, 43
% •Power Zoom Lever [T/W] .................. ੬pg. 20
T Grip Strap ............................................ ੬ pg. 10
Y Microphone......................................... ੬ pg. 52
U Video Light .......................................... ੬ pg. 21
I Tripod Mounting Socket ....................... ੬ pg. 10
•Speaker Volume Control [VOL.] ....... ੬pg. 22
^ •Picture Stabilizer Button
[P. STABILIZER] ................................. ੬pg. 20
•Time Base Corrector Button [TBC] ..... ੬pg. 23
& Power Switch
[
, OFF,
,
] .......... ੬pg. 18, 22, 28, 30
* Recording Start/Stop Button.................. ੬pg. 18
( Battery Release Switch
[BATTERY RELEASE] .............................. ੬ pg. 8
) Diopter Adjustment Control ................. ੬pg. 10
INDEX Indications
62
EN
Indications During Recording
1
2 3 4
5
6
7
120M I N
REC SP
S–ET
T
40
8
F I NE 15
&
*
444
1
N I GHT 10
x
9
!
+
02
0
@
(
S–VHS REC
MWB
a
PAUSE
1X
)
#
5
M I N
q
1 / 2
S
– – – – – – – – – –
+
–
$
^
6
BR I GHT
%
CONGRATULAT I ONS
DEC 25. 01 AM 11 45 18
b
:
:
1 •Tape Remaining Time........................ ੬ pg. 59
Blinks when a tape is about to reach its end.
•D.S.C. Mode Indicator....................... ੬ pg. 29
“DSC” appears when the D.S.C. mode is
selected.
4 •Picture Mode Display .................. ੬pg. 16, 29
•Remaining Number Of Shots
Indicator ..................................... ੬pg. 16, 29
5 Recording Format Indicator
(S/S-ET) ................................................ ੬pg. 12
2 Recording Mode Indicator (SP/EP) ........ ੬ pg. 14
6 Tape Length Indicator .......................... ੬pg. 14
3,9 Digital Effect Indicator ..................... ੬ pg. 39
Displayed at 3 for approx. 2 seconds when
the Digital Effect is switched from one mode to
another by pressing DIGIFECT, then only the
indicator remains at 9.
3,0 •Program AE Indicator.................... ੬ pg. 38
Displayed at 3 for approx. 2 seconds when
Program AE with special effects is switched
from one mode to another by pressing P.AE,
then only the indicator remains at 0.
7 Zoom Indicator Bar.............................. ੬pg. 20
Zoom Level Indicator
Approximate Zoom Ratio
8 Recording Indicator ............................. ੬pg. 18
@ Picture Stabilizer Indicator ................... ੬pg. 20
# Interval Time/Recording Time
Indicator .............................................. ੬pg. 48
$ Bright Level Indicator ........................... ੬pg. 18
% Instant Title Display ............................. ੬pg. 47
^ Date/Time Display ............................... ੬pg. 47
& Focus Indicator .................................... ੬pg. 45
* Exposure Control Level Counter ........... ੬pg. 44
( White Balance Mode Indicator ............. ੬pg. 46
) S-VHS/S-VHS ET Recording Indicator ... ੬pg. 12
q Record–Standby Mode Indicator .......... ੬pg. 18
•Night-Alive Indicator .................... ੬ pg. 36
Displayed at 3 for approx. 2 seconds when
Night-Alive is switched from one mode to
another by pressing NIGHT-ALIVE, then only
the indicator remains at 0.
3,! Fade/Wipe-Standby Indicator .......... ੬ pg. 37
Displayed at 3 for approx. 2 seconds when
the Fade/Wipe is switched from one effect to
another by pressing FADE/WIPE, then only the
indicator remains at !.
EN63
•w: Insert Editing Indicator .................. ੬ pg. 52
Displayed during Insert Editing.
1 •
: Cassette Indicator
Indications During Playback
Displayed when a tape is loaded.
1
2 3
4
5 6
7
8
2 TBC Indicator ...................................... ੬ pg. 23
3 Playback Special Effect Indicator .......... ੬ pg. 23
4 Recording Format Indicator (S/S-ET) ..... ੬ pg. 12
5 Tape Counter ................................. ੬ pg. 23, 52
6 Recording Mode Indicator (SP/EP) ........ ੬ pg. 14
7 Tape Running Indicator
–
S ET
SP
4
–
:
:
TBC
1
2 3 4 5
AT
MONOTONE
4
: Playback
3
2
6
: Fast-Forward/Shuttle Search
: Rewind/Shuttle Search
: Pause
–
:
:
M 0 1 2 3 4
e
4
: Audio Dubbing
8 Tracking Indicator ................................ ੬ pg. 23
9 Tape Counter ....................................... ੬ pg. 52
Displayed only during Insert Editing.
–––––6–––––
+
VOLUME
–
0 •BRIGHT: Bright Level Indicator .......... ੬ pg. 22
0
9
•VOLUME: Speaker Volume
Indicator ........................................... ੬ pg. 22
Warning Indications
Indications
Function
Displays the battery remaining power.
Remaining power level: high. It does not necessarily
mean that the battery pack is fully charged.
Remaining power level: exhausted
As the battery power comes close to nil, the battery indicator
power warning).
blinks (battery
When the battery power is exhausted, power turns off automatically.
Blinks when no cassette is loaded, or when the Erase Protection tab is not in the position
that allows recording.
(੬ pg. 15)
Appears when the tape ends during recording, playback or fast-forward.
Appears for 5 seconds after power is turned on if the lens cap is attached.
(੬ pg. 59)
TAPE END
LENS CAP
These 2 warnings appear alternately every 3 seconds if condensation occurs. In this case,
all functions except tape eject and power on/off are disabled. Remove the tape, turn the
unit off (without removing the power supply), wait a few minutes for the warnings to
clear, and turn it on again.
CONDENSATION
OPERATION PAUSED
PLEASE WAIT
These 2 warnings appear alternately every 3 seconds if dirt is detected on the heads
during recording. In this case, use an optional cleaning cassette. If the warning remains
after cleaning, consult your nearest JVC dealer.
HEAD CLEANING
REQUIRED
USE CLEANING
CASSETTE
E01—E06
UNIT IN
SAFEGUARD MODE
REMOVE AND
REATTACH BATTERY
The error indications (E01 — E06) show what type of malfunction has occured. If an
error indication and warning appear, turn the unit off, remove the power supply (battery,
etc.) and wait a few minutes for them to clear. When it does, you can resume using the
camcorder. If the indication remains, consult your nearest JVC dealer.
TERMS
64
EN
A
F
AC Adapter ................................................. pg. 8, 9
Animation Recording .............................. pg. 48, 51
Audio Dubbing ............................................. pg. 53
Auto Date Record ......................................... pg. 47
Auto Focus.................................................... pg. 45
Auto Shut Off .......................................... pg. 22, 59
Fade-In/Out .................................................. pg. 37
Fast-Forward Tape ......................................... pg. 22
FINE Mode .................................................... pg. 16
Fine Still........................................................ pg. 22
Full Image ............................................... pg. 29, 43
G
B
Grip Adjustment............................................ pg. 10
Battery Pack .......................................... pg. 8, 9, 66
Brighten The Image ....................................... pg. 44
Brighten The LCD Monitor ............................ pg. 18
H
High Speed Shutter Mode ............................. pg. 38
I
C
INDEX Menu ................................................ pg. 31
Index Mode .................................................. pg. 31
Index Number............................................... pg. 31
Initialization.................................................. pg. 57
Insert Editing ........................................... pg. 52, 53
Instant Delete................................................ pg. 29
Instant Titles .................................................. pg. 47
Cassette Adapter ........................................... pg. 26
Charge Marker ................................................ pg. 9
Charging The Battery Pack .............................. pg. 8
Classic Film Effect ......................................... pg. 39
Clean The Camcorder ................................... pg. 68
COM Port (RS-232C) ..................................... pg. 34
Connection To A VCR/TV ............................. pg. 24
Connection To A Windows® PC..................... pg. 34
Contents .................... cover page, 7, 17, 27, 35, 54
Counter Memory ........................................... pg. 23
J
Journalistic Shooting ..................................... pg. 19
JPEG ............................................................. pg. 29
D
L
Darken The Image ........................................ pg. 44
Darken The LCD Monitor ............................. pg. 18
Date/Time Display ........................................ pg. 47
Date/Time Settings ........................................ pg. 11
DELETE Menu ............................................... pg. 33
Delete Mode ................................................. pg. 33
Delete Select Menu ....................................... pg. 33
Demonstration Mode ................................ pg. 6, 42
Digital Effects ................................................ pg. 39
Digital Zoom ................................................ pg. 41
Digital Still Camera ............................... pg. 27 – 34
Diopter Adjustment ....................................... pg. 10
LCD monitor/Viewfinder, Indications ...... pg. 62, 63
Load A Tape .................................................. pg. 15
M
Manual Focus ............................................... pg. 45
Menu Screen......................................... pg. 40 – 42
Monotone Effect............................................ pg. 39
Move The Page Back .................................... pg. 30
Move The Page Next..................................... pg. 30
N
ND Effect Mode ............................................ pg. 38
Nega/Posi Mode ........................................... pg. 39
Night-Alive ................................................... pg. 36
E
Electronic Fog Filter Mode ............................ pg. 38
Erase Protection ............................................ pg. 15
Exposure Control .......................................... pg. 44
EN65
P
T
Padlock Mark ................................................ pg. 32
Picture Mode Setting ..................................... pg. 16
Picture Stabilizer ........................................... pg. 20
Pin-Up Image .......................................... pg. 29, 43
Playback (D.S.C.) .......................................... pg. 30
Playback (VIDEO) ......................................... pg. 22
Playback Special Effects ................................ pg. 23
Playback Zoom ............................................. pg. 51
Power Switch Position .................................. pg. 18
Program AE With Special Effects ................... pg. 38
PROTECT Menu............................................ pg. 32
Protect Mode ................................................ pg. 32
Provided Accessories ...................................... pg. 4
Tape Counter .......................................... pg. 23, 52
Tape Dubbing ......................................... pg. 24, 25
Tape Length Setting ....................................... pg. 14
Tele Macro .................................................... pg. 42
Time Base Corrector..................................... pg. 23
Time-Lapse Shooting ............................... pg. 48, 51
Tracking ........................................................ pg. 23
Tripod Mounting ........................................... pg. 10
Twilight Mode ............................................... pg. 38
U
Unload A Tape .............................................. pg. 15
V
Video Echo Effect .......................................... pg. 39
Video Light ................................................... pg. 21
Viewfinder Adjustment .................................. pg. 10
Q
Quick Review ......................................... pg. 21, 29
R
W
Recording, Advanced Features .............. pg. 35 – 48
Recording, Start/Stop (VIDEO) ................. pg. 18, 19
Recording (D.S.C.) .................................. pg. 28, 29
Recording Format ......................................... pg. 12
Recording Mode ........................................... pg. 14
Record-Standby ............................................ pg. 18
Remote Control ............................................. pg. 49
Retake ........................................................... pg. 21
Rewind The Tape .......................................... pg. 22
White Balance Adjustment ............................ pg. 46
Wide Mode ................................................... pg. 41
Wipe-In/Out.................................................. pg. 37
Z
Zooming ....................................................... pg. 20
S
Self-Recording .............................................. pg. 19
Sepia Mode ................................................... pg. 39
Shoulder Strap Attachment ............................ pg. 10
Shuttle Search ............................................... pg. 22
Slide Show Mode .......................................... pg. 30
Snapshot During Playback ............................ pg. 43
Snapshot Mode ....................................... pg. 28, 43
Snapshot (VIDEO) ......................................... pg. 43
Specifications ................................................ pg. 69
Sports Mode .................................................. pg. 38
STANDARD Mode ........................................ pg. 16
Star Mark On The Setting Menus ........... pg. 31 – 33
Still Image Data Transfer ............................... pg. 34
Still Playback ................................................ pg. 22
Store A Still Image In The Built-In Memory .... pg. 28
Strobe Effect .................................................. pg. 39
Super LoLux (S.LX) ........................................ pg. 41
Super VHS Expansion Technology ................. pg. 12
CAUTIONS
66
EN
When using the AC Adapter in areas other than the
3. Be sure to install batteries in the correct direction.
USA
4. Do not use rechargeable batteries.
Ⅲ The provided AC Adapter features automatic
voltage selection in the AC range from 110 V to
240 V.
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s AC Adapter to an AC
wall outlet other than American National Standard
C73 series type use an AC plug adapter, called a
“Siemens Plug”, as shown.
5. Do not expose the batteries to excessive heat as
they can leak or explode.
6. Do not dispose of the batteries in a fire.
7. Remove the batteries from the unit if it is to be
stored for an extended period to avoid battery
leakage which can cause malfunctions.
For this AC plug adapter, consult your nearest JVC
dealer.
Battery Packs
The battery packs are nickel-cadmium
or nickel metal-hydride batteries.
Before using the supplied battery pack
or an optional battery pack, be sure to
read the following cautions:
Plug adapter
1. To avoid hazard . . .
Video Light
... do not burn.
Terminals
... do not short-circuit the terminals.
DANGER:
... do not modify or disassemble.
•The video light becomes extremely hot. Do not
touch it either while in operation or soon after
turning it off, otherwise serious injury may result.
•Do not place the camcorder into the carrying case
immediately after using the video light, since it
remains extremely hot for some time.
•When operating, keep a distance of about 30 cm
(11-13/16" ft.) between the video light and people
or object.
... use only specified chargers.
2. To prevent damage and prolong service
life . . .
... do not subject to unnecessary shock.
... avoid repeated charging without fully
discharging.
... charge in an environment where temperatures
are within the tolerances shown in the chart
below. This is a chemical reaction type
battery—cooler temperatures impede chemical
reaction, while warmer temperatures can
prevent complete charging.
•Do not use near flammable or explosive materials.
•It is recommended that you consult your nearest
JVC dealer for replacing the video light.
... store in a cool, dry place. Extended exposure to
high temperatures will increase natural
discharge and shorten service life.
... avoid prolonged uncharged storage.
... remove from charger or powered unit when
not in use, as some machines use current even
when switched off.
General Battery Precautions
If the remote control or cassette adapter is not
functioning even if it is being operated correctly, the
batteries are exhausted. Replace them with fresh
ones.
NOTES:
Use only the following batteries:
●It is normal for the battery pack to be warm after
charging, or after use.
Remote control ................. AAA (R03) size x 2
(RM-V715U)
Cassette adapter ............... AA (R6) size x 1
(C-P6U or C-P7U)
Temperature Range Specifications
Charging .............. 10°C to 35°C (50°F to 95°F)
Operation ............ 0°C to 40°C (32°F to 104°F)
Storage ................ –10°C to 30°C (14°F to 86°F)
●Recharging time is based on room temperature of
20°C (68°F.)
Please make note of the following rules for battery
use. When misused, the batteries can leak or
explode.
1. When replacing batteries, refer to page 50 for the
remote control, or read the cassette adapter
(C-P6U/C-P7U) instructions.
●The lower the temperature, the longer recharging
takes.
2. Do not use any different size of batteries from
those specified.
EN67
Cassettes
Main Unit
To properly use and store your cassettes, be sure to
read the following cautions:
1. For safety, DO NOT . . .
... open the camcorder’s chassis.
... disassemble or modify the unit.
1. During use . . .
... short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not in
use.
... allow inflammables, water or metallic objects
to enter the unit.
... remove the battery pack or disconnect the
power supply while the power is on.
... leave the battery pack attached when the
camcorder is not in use.
... make sure the cassette bears the S-VHS-C or
VHS-C mark.
... be aware that recording onto prerecorded tapes
automatically erases the previously recorded
video and audio signals.
... make sure the cassette is positioned properly
when inserting.
... do not load and unload the cassette
repeatedly without allowing the tape to run at
all. This slackens the tape and can result in
damage.
2. Avoid using the unit . . .
... in places subject to excessive humidity or dust.
... in places subject to soot or steam such as near
a cooking stove.
... in places subject to excessive shock or
vibration.
... do not open the front tape cover. This exposes
the tape to fingerprints and dust.
2.Store cassettes . . .
... away from heaters or other heat sources.
... out of direct sunlight.
... near a television set.
... near appliances generating strong magnetic or
electric fields (speakers, broadcasting antennas,
etc.).
... in places subject to extremely high (over 40°C
or 104°F) or extremely low (under 0°C or 32°F)
temperatures.
... where they won’t be subject to unnecessary
shock or vibration.
... where they won’t be exposed to strong
magnetic fields (such as those generated by
motors, transformers or magnets).
... vertically, in their original cases.
3. DO NOT leave the unit . . .
... in places of over 50°C (122°F).
... in places where humidity is extremely low
(below 35%) or extremely high (above 80%).
... in direct sunlight.
... in a closed car in summer.
... near a heater.
... in dusty places such as a beach.
4. To protect the unit, DO NOT . . .
... allow it to become wet.
... drop the unit or strike it against hard objects.
... subject it to shock or excessive vibration during
transportation.
... keep the lens directed at extremely bright
objects for long periods.
... direct the eyepiece of the viewfinder at the sun.
... carry it by holding the viewfinder or the LCD
monitor. Be sure to hold the main unit with
both hands or use the grip.
... swing it excessively when using the shoulder
strap.
CAUTIONS (cont.)
68
EN
LCD Monitor
For Your Maintenance
1. To prevent damage to the LCD monitor,
DO NOT . . .
1. After Use
1 Set the Power Switch to “OFF” to turn off the
... push it strongly or apply any shocks.
... place the camcorder with the LCD monitor on
the bottom.
camcorder.
2 Open the LCD monitor to an angle of over 60
degrees. Slide EJECT to open the cassette
holder, then remove the cassette.
3 Close and lock the cassette holder by pressing
the Close button.
2. To prolong service life . . .
... avoid rubbing it with coarse cloth.
3. Be aware of the following phenomena for LCD
monitor use. These are not malfunctions:
4 Close and lock the LCD monitor.
•While using the camcorder, the surface around the
LCD monitor and/or the back of the LCD monitor
may heat up.
•If you leave power on for a long time, the surface
around the LCD monitor becomes hot.
5 Slide BATTERY RELEASE to remove the battery
pack.
6 Attach the provided lens cap to the camcorder’s
lens.
2. Cleaning The Camcorder
1 CLEAN EXTERIOR
Wipe gently with a soft cloth.
Put cloth in diluted mild soap and wring it well
to wipe off heavy dirt, then wipe again with a
dry cloth.
How To Handle a CD-ROM
•Take care not to soil or scratch the mirror surface
(opposite to the printed surface). Do not write
anything or put a sticker on either the front or back
surface. If the CD-ROM gets dirty, gently wipe it
with a soft cloth outward from the center hole using
a circular motion.
2 CLEAN LCD MONITOR
Open the LCD monitor and wipe it gently with
a soft cloth. Be careful not to damage the
monitor. Close the LCD monitor.
•Do not use conventional disc cleaners or cleaning
spray.
•Do not bend the CD-ROM or touch its mirror
surface.
•Do not store your CD-ROM in a dusty, hot or
humid environment. Keep it away from direct
sunlight.
3 CLEAN LENS
Blow it with a blower brush, then wipe it gently
with lens cleaning paper.
4 REMOVE EYEPIECE
Turn the eyepiece counterclockwise and pull it
out.
5 CLEAN VIEWFINDER
Remove dust using a blower brush.
6 RE-ATTACH EYEPIECE
About moisture condensation . . .
Re-attach the eyepiece and turn it clockwise.
● You may have observed that pouring a cold
liquid into a glass will cause drops of water to
form on the glass’ outer surface. This same
phenomenon occurs on the head drum of a
camcorder when it is moved from a cool place
to a warm place, after heating a cold room,
under extremely humid conditions or in a
place directly subjected to the cool air from an
air conditioner.
NOTES:
● Avoid using strong cleaning agents such as benzine
or alcohol.
● Cleaning should be done only after the battery
pack has been removed or other power units have
been disconnected.
● Mold may form if the lens is left dirty.
● When using a cleaner or chemically treated cloth,
refer to the cautions that came with it.
● When removing the eyepiece, be sure to hold the
viewfinder securely.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the camcorder itself.
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
SPECIFICATIONS
EN69
Viewfinder
: Electronic viewfinder with
Camcorder
0.55" color LCD
General
White balance
adjustment
LCD monitor
: Auto/Manual adjustment
Format
Power source
: S-VHS/VHS NTSC standard
: DC 11 V
(Using AC Adapter)
DC 6 V
(Using battery pack)
: 3" diagonally measured, LCD
panel/TFT active matrix
system
Speaker
: Monaural
Power consumption
Viewfinder on
LCD monitor on
Video light
Connectors
: 4.7 W
: 5.4 W
: 3.0 W
Video
: 1 V (p-p), 75 Ω unbalanced,
analog output
(via Video output connector)
Signal system
: NTSC-type
Audio
: 300 mV (rms), 1 kΩ analog
Video recording system
Luminance
Color
output
: FM recording
: Converted sub-carrier
direct recording
(via Audio output connector)
Digital
: ø2.5 mm, 4-pole, mini-head
jack
Conforms to VHS standard
S-Video
: Y : 1 V (p-p), 75 Ω,
Cassette
Tape speed
SP
EP
:
/
cassette
analog output
C : 0.29 V (p-p), 75 Ω,
analog output
: 33.35 mm/sec. (1-5/16 ips)
: 11.12 mm/sec. (7/16 ips)
Recording time (max.)
AC Adapter AP-V10U
Power requirement : AC 110 V to 240 V`,
SP
: 40 minutes
EP
: 120 minutes (with TC-40)
50 Hz/60 Hz
D.S.C. format
Recording format : Digital data storage
Output
Dimensions
(W x H x D)
: DC 11 V
, 1 A
: 59 mm x 31 mm x 69 mm
(2-3/8" x 1-1/4" x 2-3/4")
: Approx. 130 g (0.29 lbs)
(based on JPEG)
Recording medium : Built-in flash memory,
Weight
2 Mbyte
Number of storable shots
Optional Accessories
FINE mode
: approx. 30 shots
•Battery Packs BN-V12U, BN-V20U, BN-V400U
•A/V (Audio/Video) Cable
•S-Video Cable QAM0004-004
STANDARD mode: approx. 60 shots
Image size
: 640 x 480 pixels
(when captured on a PC)
Operating
temperature
•Compact S-VHS (
•Compact VHS (
) Cassettes ST-C-40/30/20
) Cassettes TC-40/30/20
: 0°C to 40°C (32°F to 104°F)
Operating humidity : 35% to 80%
Storage temperature : –20°C to 50°C
(–4°F to 122°F)
•Active Carrying Bag CB-V7U
Weight
Dimensions
: Approx. 930 g (2.1 lbs)
Some accessories are not available in some areas.
Please consult your nearest JVC dealer for details on
accessories and their availability.
: 206 mm x 112 mm x 118 mm
(8-1/8" x 4-7/16" x 4-11/16")
(with the LCD monitor closed
and with the viewfinder fully
tilted downward)
Pickup
Lens
: 1/4" format CCD
: F1.6, f = 3.9 mm to 62.4 mm,
16:1 power zoom lens with
auto iris and macro control,
filter diameter 40.5 mm
Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications subject to change
without notice.
MEMO
MEMO
EN
VICTOR COMPANY OF JAPAN, LIMITED
1P1ri0n0teMdKinV*JaUpNan*YP
UM
COPYRIGHT© 2000 VICTOR COMPANY OF JAPAN, LTD.
|