JBL GTO5355OM User Manual

GTO5355  
OWNER’S MANUAL  
BEDIENUNGS-  
ANLEITUNG  
MODE D'EMPLOI  
MANUAL DE USO  
HANDLEIDING  
MANUALE UTENTE  
ANVÄNDAR-  
HANDBOK  
BRUGSVEJLEDNING  
OMISTAJAN  
KÄSIKIRJA  
PODRĘCZNIK  
UŻYTKOWNIKA  
РУКОВОДСТВО  
ПОЛЬЗОВАТЕЛЯ  
È
À
ý
1.000  
ENGLISH  
GTO5355 CAR AUDIO POWER AMPLIFIER OWNER’S MANUAL  
G
Installation Warnings and Tips  
• Disconnect the negative (–) lead from your vehicle’s  
battery.  
• At the installation sites, locate and make a note of  
all fuel lines, hydraulic brake lines, vacuum lines  
and electrical wiring. Use extreme caution when  
cutting or drilling in and around these areas.  
• Choose a safe mounting location away from  
moisture.  
• Make sure there is sufficient air circulation at the  
mounting location for the amplifier to cool itself.  
• GND: Connect to the vehicle’s chassis. Refer to  
the picture below.  
Protect LED  
• Illuminated under any of the following fault  
conditions: battery over/under voltage, short  
circuit in speaker wires, amplifier is too hot,  
amplifier’s output circuit has failed (DC voltage  
present in the amplifier’s output).  
Subwoofer Low-Pass Filter Frequency Control  
• 12dB/octave low-pass filter, variable from 20Hz  
to 200Hz.  
• See the adjustment procedure in  
DBO (Dynamic Bass Optimization)  
Variable Subsonic High-Pass Filter With  
Variable Boost (Q)  
Factory Bolt  
Ring Connector  
Ground Wire  
H
I
K
.
Note: Remove any paint  
below ring connector.  
Star Washer  
• Mount the amplifier, using the supplied hardware.  
• REM: Connect to the “Remote Out” lead from  
the source unit or to a source of switched  
12V+ (ACC).  
Front Input Connectors (RCA)  
• Connect to the front RCA outputs from the  
source unit or signal processor.  
Front Input-Level Control  
• Used to match the front input level of the  
amplifier to the output level of the source unit.  
• For woofers in tuned (vented) enclosures, set  
the Frequency control to a value 10Hz below the  
enclosure’s resonance (tuned) frequency.  
• For woofers in sealed boxes, set the control to  
any value you prefer between 30Hz and 50Hz.  
• Set the Boost control according to your  
preference, being careful not to apply  
enough boost to damage your woofer(s).  
Specifications  
• 55W RMS x 4 channels, plus 225W RMS  
x 1 channel, @ 4 ohms and 1% THD + N*  
• 75W RMS x 4 channels, plus 360W RMS  
x 1 channel, @ 2 ohms and 1% THD + N*  
• THD + N: 0.03% (rated power @ 4 ohms)  
• Signal-to-noise ratio: 85dB  
(reference 1W into 4 ohms)*  
• Signal-to-noise ratio: 104dB  
(reference rated power into 4 ohms)  
• Frequency response: 10Hz – 83kHz and  
20Hz – 250Hz  
• Max power: 660 watts  
* CEA-2006A-compliant  
3
4
A DBO High-Pass Filter Frequency control,  
variable between 20Hz and 100Hz.  
J
• See for the adjustment procedure.  
See above for appropriate settings.  
5
6
Front Crossover-Frequency Control  
• 12dB/octave crossover, variable from  
32Hz to 320Hz.  
B DBO Boost control provides up to  
12dB of boost, slightly above the high-  
pass filter’s frequency. See above for  
appropriate settings.  
K
• See for the adjustment procedure.  
Front Crossover-Filter Selector  
• LPF: Select for subwoofer(s).  
• Flat: Select for full-range speakers when  
no subwoofer will be used in the system.  
• HPF: Select for midrange speakers or  
full-range speakers when a subwoofer is  
used in the system.  
Power On LED  
• Illuminated when the amplifier is on.  
Subwoofer Input Connector (RCA)  
• Connect to the subwoofer RCA outputs from  
the source unit, or signal processor.  
Rear Crossover-Filter Selector  
• LPF: Select for subwoofer(s).  
• Flat: Select for full-range speakers when  
no subwoofer will be used in the system.  
• HPF: Select for midrange speakers or  
full-range speakers when a subwoofer is  
used in the system.  
Rear Crossover-Frequency Control  
• 12dB/octave crossover, variable from  
32Hz to 320Hz.  
J
Setting Input Level  
0
Speaker Output Connectors  
A Turn all Input-Level controls counterclockwise  
to 6V (minimum).  
• Connect the speakers to these terminals,  
observing proper polarity.  
B With a dynamic music track playing, turn the  
head unit’s volume control to the 3/4 position.  
• Five-channel operation: Connect the front left  
speaker to the Front L+ and L– terminals and  
the front right speaker to the Front R+ and  
R– terminals. Repeat for the rear speakers,  
using the Rear L+ and L– terminals, and  
the Rear R+ and R– terminals. Connect the  
subwoofer to the Sub+ and Sub– terminals.  
• Four-channel operation: Connect the stereo  
speakers to the Front terminals, as above.  
Connect the single speaker into which the  
amplifier’s rear channels will be bridged to the  
Rear R+ and Rear L– terminals. Connect the  
subwoofer to the Sub+ and Sub– terminals  
• Three-channel (bridged) operation: Connect  
one speaker to the Front R+ and Front L–  
terminals. Connect the other speaker to the  
Rear R+ and Rear L– terminals. Connect the  
subwoofer to the Sub+ and Sub– terminals.  
• Minimum speaker impedance for stereo  
operation is 2 ohms. Minimum speaker  
impedance for bridged operation is 4 ohms.  
Minimum subwoofer impedance is 2 ohms.  
C Turn Front Input-Level control clockwise until  
the music is so loud that it no longer sounds  
clear (distortion is present in the output).  
D Turn Front-Input-Level control counterclock-  
wise gradually, just until the music sounds  
clear, once again.  
7
8
E Front-Level input is now adjusted correctly.  
9
F Adjust the Rear and Sub Input-Level controls  
so that the level of the rear speakers and the  
level of the subwoofer are proportionate to the  
level of the front speakers, according to your  
preference.  
K
Setting the Crossover  
A Crossover setting for 5" or larger full-range  
speakers when no subwoofer is included in  
the system.  
A
B
B Crossover setting for full-range speakers  
K
• See the adjustment procedure in  
.
when a subwoofer is included in the system.  
Rear Input-Level Control  
• Used to match the rear input of the amplifier to  
the output of the source unit.  
C Crossover setting for subwoofers.  
D Crossover setting for systems that include  
separate mid-bass speakers driven by the rear  
channels, with the BP switch set to “BP.”  
Note: Acceptable frequency ranges are indicated  
in gray.  
1
2
Fuses  
J
• See for adjustment procedures.  
• Replace only with same type and rating.  
Power Input Connectors  
C
D
Rear Input Connectors (RCA)  
• Connect to rear RCA outputs from the source  
unit, or signal processor.  
• +12V: Connect to the positive terminal of the  
vehicle’s battery. 4 AWG wire is recommended.  
Install an appropriate fuse holder and fuse  
(80A minimum) within 18 inches of the battery.  
Make sure the wire is not damaged or pinched  
during installation. Install protective grommets  
when routing wires through the firewall or other  
sheet metal.  
L
Remote Level Control  
EXT/INT Switch  
The Remote Level Control, if installed, will allow  
you to adjust the level of bass while seated in the  
listening position.  
• If the source unit has a subwoofer output and  
you have connected it to the SUB input, set this  
switch to the EXT position. Otherwise, set it in  
the INT position.  
Subwoofer Remote Level Control Connector  
• Connect the Remote Level Control (RLC) here,  
using the supplied RJ-11 cable.  
E
F
Subwoofer Level Control  
• Used to match the SUB input of the amplifier to  
This product is designed for mobile applications and is not  
intended for connection to the mains.  
A valid serial number is required for warranty coverage.  
Features, specifications and appearance are subject to change  
without notice.  
the output of the source unit.  
J
• See for adjustment procedures.  
Konformitätserklärung  
Harman Deutschland GmbH  
Hünderstraße 1 * 74080 Heilbronn * Telefon: 07131 / 480 0  
Wir, Harman Consumer Group, Inc.  
2, route de Tours  
72500 Château du Loir - Frankreich  
erklären in eigener Verantwortung, dass das hier beschriebene  
Produkt folgenden Standards entspricht:  
EN 55013:2001+A1:2003  
© 2007 Harman International Industries, Incorporated. Alle Rechte vorbehalten.  
JBL ist eine Marke von Harman International Industries, Incorporated, eingetragen in  
den Vereinigten Staaten und/oder anderen Ländern.  
EN 55020:2002+A1:2003  
Klaus Lebherz  
Harman Consumer Group, Inc.  
Château du Loir, Frankreich 8/07  
Teile-Nr.: GTO5355OM 8/07  
Declaration of Conformity  
We, Harman Consumer Group, Inc.  
2, route de Tours  
72500 Château du Loir  
France  
Harman Consumer Group, Inc.  
250 Crossways Park Drive, Woodbury, NY 11797  
declare in own responsibility that the product described in this owner’s  
manual is in compliance with technical standards:  
EN 55013:2001+A1:2003  
© 2007 Harman International Industries, Incorporated. All rights reserved.  
EN 55020:2002+A1:2003  
JBL is a trademark of Harman International Industries, Incorporated,  
registered in the United States and/or other countries.  
Klaus Lebherz  
Part No. GTO5355OM 8/07  
Harman Consumer Group, Inc.  
Château du Loir, France 8/07  
www.jbl.com  

Alpine 68 13530Z42 A User Manual
Bosch Appliances MSM 5110 UC User Manual
Canon Camcorder T5i User Manual
Elevation Audio DX2000 1 User Manual
Hitachi VM 3800A User Manual
IDEAL INDUSTRIES ICOS HE12 User Manual
Jeep 50 0284x 015 Series User Manual
JVC Car Stereo System KS FX725R User Manual
JVC Everio GZ HM340U User Manual
JVC GR AXM236UC User Manual