TSS-Sub500
(TSS-500 SYSTEM)
SERVICE MANUAL
Infinity Systems Incorporated
250 Crossways Park Dr.
Woodbury, New York 11797
Rev0 6/2006
TSS-Sub500
TSS-500 PACKING/ACCESSORIES
Item #
Description
Part Number
Qty
1
2
3
4
5
6
7
8
9
Warranty Card
Owner’s Manual
Packing
Packing Bag
Inner Carton
Packing Bag
Nut wrench (metal bar)
15’ RCA cable
405-000-05110-E
406-000-05307-E
Not for Sale
Not for Sale
Not for Sale
Not for Sale
399-FE-00630-E
370-000-00273-E
373-000-05051-E
373-000-05050-E
371-000-05108-E
1
1
1
4
1
1
1
1
1
1
1
1
1
1
2
3
4
4
5
1
1
1
1
1
1
3
1
1
Rubber feet for stands (Platinum)
Rubber feet for stands (Charcoal)
Screw for stands (5) ¼ x 20 x1” (Platinum)
10
11
Screw for stands (5) ¼ x 20 x1” (Charcoal) 371-000-05114-E
Wall Bracket ball end (5) (Platinum)
Wall Bracket ball end (5) (Charcoal)
40’ Wire set (2)
373-000-05054-E
373-000-05055-E
370-000-00276G-E
370-000-00277G-E
325-ABS-05126-0VAE
325-ABS-05127-0BAE
398-ABS-00317-0VAE
325-ABS-05127-0VAE
325-ABS-05126-0BAE
336-RUB-05200-0VAE
431-000-05639-E
Not for Sale
12
13
14
20’ Wire set (3)
Satellite stand (Platinum)
Satellite stand (Charcoal)
Wall bracket
Center table stand (Platinum)
Center table stand (Charcoal)
Rubber gasket for stand
Subwoofer Top Packing
Packing Bag
Subwoofer Btm Packing
Desiccant
Outer Carton (Platinum)
Outer Carton (Charcoal)
15
16
17
18
19
20
21
22
431-000-05640-E
Not for Sale
402-000-05533-E
402-000-05534-E
2
TSS-Sub500
TSS-Sub500
100W Powered Sub/ Plate Amp
LINE VOLTAGE
US 120VAC/60Hz
Europe 220-240VAC, 50-60Hz
Yes/No
Yes
Yes
Hi/Lo Line
108-132 Vrms
220-240 Vrms
Unit
Notes
Normal Operation
Normal Operation
Parameter
Specification
Unit
QA Test Limits
Conditions
Notes
Amp Section
Type (Class AB, D, other)
Type (Class AB, D, other)
Load Impedance (speaker)
Rated Output Power
THD@ Rated Power
THD @ 1 Watt
AB
G
4
100
0.5
0.1
10
AB
G
Ohms
Watts
%
n/a
n/a
n/a
95
1
120V Model
230V Model
Nominal
Single input driven
22K filter
External Sink required
External Sink required
%
mV-DC
0.5
50
22K filter
@ Speaker Output
DC Offset
Measured at amplifier board speaker output
terminals, Output power 90 Watts
Damping factor
>100
DF
100
50Hz, 4 Ohms load
Input Sensitivity
Input Frequency
Line Input (L&R)
LFE Input
50
13.8
8.62
Hz
mVrms
mVrms
50
±2dB
±2dB
Nominal Freq.
To 1 Watt
To 1 Watt
Single input driven, AP Zo=600 Ohms
LFE input driven only, AP Zo=600 Ohms
Signal to Noise
SNR-A-Weighted
SNR-unweighted
SNR @ 1W-unweighted
100
80
60
dBA
dBr
dBr
85
80
60
rel. to rated power
rel. to rated power
rel. to 1W Output
A-Weighting filter
22K filter
22K filter
Volume @max, using RMS reading
DMM/VOM (or A/P)
Residual Noise Floor
Residual Noise Floor
1
1
mVrms
mVrms(max)
K ohms
2
2
Volume @max, w/ A/P Swept Bandpass
Measurement (Line freq.+ harmonics)
Input Impedance
Line input L&R , LFE
>10
n/a
Nominal
Filters
Low Pass (fixed or variable)
Subsonic filter (HPF)
4th order fix
2nd order
--
Hz
±2dB
±2dB
Limiter (yes/no)
THD at Max. Output Power
YES
1
--
%
Functional
Functional
Features
LFE Input
Volume pot Taper (lin/log)
ATO
YES
LOG
YES
Functional
Functional
Functional
--
--
Input Configuration
Line In (L,R)
Line level in LFE
L ,R
LFE
Functional
Functional
RCA inputs
Signal Sensing (ATO)
Auto-Turn-On (yes/no)
YES
50
--
Functional
Functional
ATO Input Frequency
Hz
2mV@50Hz into Line Input w/ 1 ch.
driven
Amp connected and AC on, then input
signal applied
ATO Level
2
5
mV
ms
Functional
Functional
Functional
Functional
ATO Turn-on time
Auto Mute/ Turn-OFF Time
Power on Delay time
10
3
minutes
sec.
T before muting, after signal is removed Auto turn of time (T) must be 5 > T <15
AC Power Applied
Transients/Pops
ATO Transient
Turn-on Transient
Turn-off Transient
5
50
50
mV-peak
mV-peak
mV-peak
10
100
100
Speaker Outputs
Speaker Output
Speaker Output
AC Line cycled from OFF to ON
AC Line cycled from ON to OFF
Efficiency
Maximum allowable input power under
nominal Input voltage and frequency, HOT
or COLD operation.
Stand-by Input Power
Power Cons.@rated power
12
195
Watts
Watts
15
210
@ nom. line voltage
@ nom. line voltage
100 Watts @ 4 Ohms nominal line voltage
3
TSS-Sub500
Parameter
Specification
Unit
QA Test Limits
Conditions
Notes
Protection
Short Circuit Protection
YES
--
Functional
Direct short at output
Temperature rise should not exceed 35K
rise
Relay or crowbar (for driver/fire protection)
Thermal Protection
DC Offset Protection
65 deg. C
YES
--
--
Functional
Functional
@1/8 max unclipped Power
DC present at Speaker Out leads
Line Fuse Rating
120 VAC
External fuse with UL/SEMKO rated holder
Type-T or Slo Blo, Fuse Markings T2.5A,
250V
Type-T, Low breaking capacity, Fuse
markings T1.25AL, 250V
2.5
Amps
Amps
230 VAC
1.25
4
TSS-Sub500
SUBWOOFER CONTROLS
Rear Panel
¡
A Few Suggestions
We recommend that you do not operate your speakers or
subwoofer with the bass, treble and loudness controls set to
full boost.This will place undue strain on your electronics and
speakers and could damage them.
£
™
The volume control setting on your processor/preamp or receiver
is not a specific indication of the overall loudness level of the
speakers.The only important consideration is the loudness level at
which the system can be played, regardless of where the volume
control is set.
Always turn down the volume control setting on your processor/
preamp or receiver when changing a cassette or CD, or switching
inputs to AM or FM operation. Excessively loud transients (clicks or
popping sounds) can damage the satellite speakers and possibly
the subwoofer.
R
¢
TSS-Sub500
Important!
NRTL/C
CSA 22-2 NO.1
UL 1492
This area is designed to become quite warm
during normal operation.
Whenever changing cables, pulling plugs, etc.,ALWAYS TURN OFF
ALL EQUIPMENT, including the subwoofer.
¡
™
£
¢
Subwoofer Level Control
LFE Input
Line-Level Inputs
Power Switch
5
TSS-500
5
TSS-Sub500
SUBWOOFER CONNECTIONS
If you have a Dolby® Digital or DTS® receiver/
processor with a low-frequency-effects (LFE)
or subwoofer output:
If your receiver/processor does not contain
a Dolby Digital or DTS processor but has a
subwoofer output:
15' (4.6m) subwoofer
cable included
RECEIVER/PROCESSOR
15' (4.6m) subwoofer
cable included
SUBWOOFER OR
LFE OUTPUT
NOTE: If your receiver/processor has only one sub out,
you may use either the L or R input.
6
TSS-500
6
TSS-Sub500
OPERATION
Surround Modes
When using the TSS-500 in a Dolby Digital or DTS home theater
system, make sure all speakers are set to“Small”. When using the
system in a Dolby Pro Logic® home theater system, make sure the
receiver’s center channel mode is set to“Normal”.
enhance bass, extending the response of the entire system so
the bass can be felt as well as heard. However, overall balance
must be maintained or the music will not sound natural.An
experienced listener will set the volume of the subwoofer so its
impact on bass response is always there but never obtrusive.
Some Dolby Digital-equipped receivers/processors offer different
setup options for each source or surround mode (e.g., CD-stereo,
videotape, Dolby Digital, Pro Logic). In each case, follow your
equipment’s instructions to ensure that the subwoofer output is
turned on and that the speakers are set to“Small”in each mode.
Final Positioning
After correctly connecting the TSS-500 system and verifying
that both the subwoofer and all satellite speakers are playing,
it is time to optimize the system for your particular listening
room. Earlier, you placed the subwoofer in its general location.
Finding the exact location for optimum performance sometimes
only involves moving the speakers up to a few inches in any
direction.We urge you, therefore, to experiment with placement,
if possible, until your speakers deliver their full potential.
If your receiver has adjustable crossover settings, we recommend
the subwoofer crossover be set between 100Hz and 120Hz.
Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use the
outlets on the back of the receiver.
ᕡ
Initially set the Subwoofer Level Control
to the“MIN”position.
MAINTENANCE AND SERVICE
ᕤ
Turn on the subwoofer by pressing the Power Switch on the
rear panel.
The satellite and subwoofer enclosures may be cleaned using a
soft cloth to remove fingerprints or to wipe off dust.
Turn on your entire audio system and start a CD or movie
soundtrack at a moderate level.
All wiring connections should be inspected and cleaned or
remade periodically.The frequency of maintenance depends on
the metals involved in the connections, atmospheric conditions
and other factors, but once per year is the minimum.
Auto On/Standby
With the Power Switch
ᕤ
in the ON position, the LED on the back
will remain lit in green or red to indicate the ON/STANDBY mode of
the subwoofer.
If a problem occurs, make sure that all connections are properly
made and clean. If a problem exists in one loudspeaker, reverse
the connection wires to the left and right system. If the problem
remains in the same speaker, then the fault is with the loud-
speaker. If the problem appears in the opposite speaker, the
cause is in another component or cable. In the event that your
TSS-500 ever needs service, contact your local Infinity dealer or
RED = STANDBY (No signal detected,Amp Off)
GREEN = ON (Signal detected,Amp On)
The subwoofer will automatically enter the Standby mode after
approximately 10 minutes when no signal is detected from your
system.The subwoofer will then power ON instantly when a signal
ᕤ
is detected. During periods of normal use, the Power Switch
ᕤ
can be left on.You may turn off the Power Switch
for extended
periods of nonoperation, e.g., when you are away on vacation.
Adjust Level
Turn the Subwoofer Level Control
ᕡ
up about halfway. If no sound
emanates from the subwoofer, check the AC-line cord and input
cables.Are the connectors on the cables making proper contact?
Is the AC plug connected to a“live”receptacle? Has the Power
ᕤ
Switch
been pressed to the“On”position? Once you have
confirmed that the subwoofer is active, proceed by playing a CD
or DVD. Use a selection that has ample bass information.
Set the overall volume control of the receiver/processor to a
ᕡ
comfortable level.Adjust the Subwoofer Level Control
until
you obtain a pleasing blend of bass. Bass response should
not overpower the room but rather be adjusted so there is
a harmonious blend across the entire musical range. Many
users have a tendency to set the subwoofer volume too loud,
adhering to the belief that a subwoofer is there to produce
lots of bass.This is not entirely true.A subwoofer is there to
7
TSS-500
7
TSS-Sub500
Test Set Up and Procedure
Equipment needed:
• Function/signal generator/sweep generator
• Integrated Amplifier
• Multimeter
• Speaker cables
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R
on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to
the single LFE input.
2) On the front of the unit, turn the LEVEL control full counterclockwise.
3) Turn on generator, adjust to 100mV, 50 Hz.
4) Plug in UUT; turn the power switch ON. LED should be Red. Turn LEVEL control full clockwise (MAX)
5) LED should now be Green; immediate bass response should be heard and felt from port tube opening.
6) Turn off generator, turn LEVEL control fully counterclockwise, disconnect RCA cable.
Sweep Function
1) Follow steps 3-6 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips.
2) Check DC resistance of woofer; it should be 3.3 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
9
TSS-Sub500
TSS500
Troubleshooting Flow Chart
AMP no signal out
no
Check fuse, transformer,
yes
D110,D115 etc
yes
DC voltage check ±Vcc
yes
no
Check Q117,118,119,D109 etc
yes
Check +/-15v
yes
LED red
Led light blue or red
Check,Q203,207,U203 etc
LED light blue
yes
yes
Check U201,R226,223 ,
U202,R213,214,C206
etc
Check U201
pin14 signal
no
Check U202 pin14 signal
yes
yes
no
no
Check limiter board C304
Check U301,R343,344 ,
C340,Q301,302, etc
yes
yes
yes
no
Check ,+vsw& -vsw
DC voltage
Test R121,122 signal
Check Q120,121,122,123
Q124,125,126,127 etc
no
yes
yes
Check Q107,108,105,
Q106,103,104,U101,etc
Check RLY101,D102,Q113,114
yes
no
Change the component
Check U101,Q115,116,R138
yes
yes
Check P102 signal
The Amp ass’y ok, END
11
TSS-Sub500
TSS-Sub500 (120v) Electrical Parts List
Description
Reference Designator
Qty
Part Number
PREAMP PCB
Resistors
R213,214,215,254
110-16102j26
Resistor 1K 1/6W ±5% CF 26mm
4
R212,216,217,220,221,222,225,228,226,232,
235,240,248
R231,266
R259
R264
R233
R253
R234
R252
R262,227
R257
R238,247,250,255
R223,237
R249
R258,260
R219,251
R211,229 ,230
R224
110-16103j26
110-16104j26
110-16105j26
110-16122j26
110-16124j26
110-16151j26
110-16153j26
110-16154j26
110-16183j26
110-16205j26
110-16223j26
110-16273j26
110-16333j26
110-16472j26
110-16473j26
110-16512j26
110-16513j26
115-h503a104
Resistor 10K 1/6W ±5% CF 26mm
Resistor 100K 1/6W ±5% CF 26mm
Resistor 1M 1/6W ±5% CF 26mm
Resistor 1.2K 1/6W ±5% CF 26mm
Resistor 120K 1/6W ±5% CF 26mm
Resistor 150Ω 1/6W ±5% CF 26mm
Resistor 15K 1/6W ±5% CF 26mm
Resistor 150K 1/6W ±5% CF 26mm
Resistor 18K 1/6W ±5% CF 26mm
Resistor 2M 1/6W ±5% CF 26mm
Resistor 22K 1/6W ±5% CF 26mm
Resistor 27K 1/6W ±5% CF 26mm
Resistor 33K 1/6W ±5% CF 26mm
Resistor 4.7K 1/6W ±5% CF 26mm
Resistor 47K 1/6W ±5% CF 26mm
Resistor 5.1K 1/6W ±5% CF 26mm
Resistor 51K 1/6W ±5% CF 26mm
variable Resistor D16 50K/1 A LEVEL
13
2
1
1
1
1
1
1
2
1
4
2
1
2
2
3
1
1
VR201
Capacitors
C207,208,210,211,212,214,220,230,249
C232,242,244,245,246,252,254
C229
C223,224
C218,221,222
C215
C216,217
C228
130-2b221k503
130-3f104z503
130-sl470k503
132-103j503
132-104j503
132-223ja03
132-473j503
135-3105m50
135-3106m50
135-3107m16
135-3226m50
disc Capacitor 220P 50V ± 10%
disc Capacitor 0.1U 50V +80/-20%
disc Capacitor 47P 50V ± 10%
electrolytic 0.01U 50V ± 5%
electrolytic 0.1U 50V ± 5%
electrolytic 0.22uF 100V ± 5%
electrolytic 0.047U 50V ± 5%
electrolytic 1U 50V ± 20%
9
7
1
2
3
1
2
1
8
2
1
C206,213,219,231,241,243,251,253
C233,234
C225
electrolytic 10uF 50V ± 20%
electrolytic 100uF 16V ± 20%
electrolytic 22U 50V ± 20%
Semiconductors
Q201,206,207
D201,202,207,208,211,212,214
D213
U203
U201,202
D209
192-027c1815gr
197-031n4148
199-15000335
190-06m4558d
190-16t1074cn
195-10204hgw
Transistor 2SC1815GR NPN
diode 100mA 75V SIGNAL 1N4148 ROHM
zener diode 3.3V 1/2W 52mm
I.C OPA 4558D DUAL OP-AMP
I .C TL074cm QUAD OP-AMP
LED 204HGW 3c
3
7
1
1
2
1
Miscellaneous
for D209
JK202
162-50159201
174-0rca326p
WIRE ASS'Y 2PIN 150mm
JACK RCA-326
1
1
POWER/MAIN PCB
Resistors
R147,150
R148,151
110-14472j26
110-14681j26
Resistor 4.7K 1/4W ±5% 26mm
Resistor 680Ω 1/4W ±5% 26mm
2
2
20
TSS-Sub500
Description
Reference Designator
Part Number
Qty
POWER/MAIN PCB
R120
R124
R134
R143
110-16101j26
110-16102j26
110-16103j26
110-16105j26
110-16123j26
110-16152j26
110-16153j26
110-16154j26
110-16181j26
110-16182j26
110-16223j26
110-16332j26
110-16392j26
110-16393j26
110-16470j26
110-16471j26
110-16472j26
110-16473j26
110-16560j26
110-16563j26
110-16682j26
110-10821jk2
110-122r2j15
110-20331jk2
113-50r10j10
114-03302m0
Resistor10 0Ω 1/6W ±5%CF 26mm
1
1
1
1
2
6
4
1
2
1
3
3
2
1
4
1
3
1
1
1
1
1
1
2
2
1
Resistor 1K 1/6W ±5% CF 26mm
Resistor 10K 1/6W ±5% CF 26mm
Resistor 1M 1/6W ±5% CF 26mm
Resistor 12K 1/6W ±5% CF 26mm
Resistor 1.5K 1/6W ±5% CF 26mm CF
Resistor 15K 1/6W ±5% CF 26mm
Resistor 150K 1/6W ±5% CF 26mm
Resistor 18Ω 1/6W ±5% CF 26mm
Resistor 1.8K 1/6W ±5% CF 26mm
Resistor 22K 1/6W ±5% CF 26mm
Resistor 3.3K 1/6W ±5% CF 26mm
Resistor 3.9K 1/6W ±5% CF 26mm
Resistor 39K 1/6W ±5% CF 26mm
Resistor 47Ω 1/6W ±5%CF 26mm
Resistor 470Ω 1/6W ±5% CF 26mm
Resistor 4.7K 1/6W ±5% CF 26mm
Resistor 47K 1/6W ±5% CF 26mm
Resistor 56Ω 1/6W ±5% CF 26mm
Resistor 56K 1/6W ±5% CF 26mm
Resistor 6.8K 1/6W ±5% CF 26mm
Resistor 820Ω 1W ±5% 10mm
R135,139
R103,123,136,137,141,142
R118,145,152,154
R131
R111,114
R153
R128,129,133
R106,107,144
R105,108
R126
R112,113,115,116
R140
R110,125,130
R101
R117
R104
R109
R132
R127
R146,149
R121,122
R138
Resistor 2.2Ω 1/2W ±5% 15mm
Resistor 330Ω 2W ±5% 5mm
cement Resistor 0.1Ω 5W ±5%
semi-fixed Resistor 3K 0.3W 1±20%
Capacitors
C116
C108.113.115.119
C106
C139,140
C107
C124,125,126,128
C105,112
C109,117,120
C114,118
C129,130
C111
C103
C123,127
C110
130-2b102k503
130-2f104z503
130-3f473m503
130-s1101k503
132-104j503
disc Capacitor 1000p 50V±10%
disc Capacitor0.1u 50V+80/ -20%
disc Capacitor0.047u 50V±20%
disc Capacitor100p 50V SL±10%
mylar Capacitor 0.1u50V ±5%
mylar Capacitor 0.022uF 100V ±5%
mylar Capacitor 1U 50V ±20%
mylar Capacitor100uF 16V ±20%
mylar Capacitor22U 50V ±20%
mylar Capacitor220U 10V ±20%
mylar Capacitor220U 16V ±20%
mylar Capacitor47U 25V ±20%
mylar Capacitor 0.022uF 100V ±5%
electrolytic 100uF 16V ±20%
1
4
1
2
1
4
2
3
2
2
1
1
2
1
2
132-223ja03
135-3105m50
135-3107m16
135-3226m50
135-3227m10
135-3227m16
135-3476m25
132-223ja03
135-3107m16
135-4688m50
C121,122
electrolytic 6800U/50V ±20% D25X45mm
Semiconductors
Q102,111,112,113,118
Q114,116
Q103,109
Q104,110
D101,103,105,108
D102
D106,107
D109
U101
Q107
Q108
Q101,115
Q117
192-027c1815gr
192-028a1015gr
192-1572n5551
192-1582n5401
197-031n4148
199-15000335
199-15000625
199-15001605
190-06m4558d
192-021tip35c
192-022tip36c
192-027c1815gr
192-201d882Y
Transistor 2SA1815GR NPN
Transistor 2SA1015GR PNP
Transistor 2N5551 NPN
Transistor 2N5401 AI-PNP 350V 500MA TO-92
diode 100mA 75V SIGNAL 1N4148 ROHM
zener diode3.3V 1/2W 52mm
zener diode 6.2V 1/2W 52mm
zener diode 16V 1/2W 52mm
IC OPA 4558D DUAL OP-AMP
Transistor TIP35C NPN
5
2
2
2
4
1
2
1
1
1
1
2
1
Transistor TIP36C PNP
Transistor 2SC1815GR NPN
TransistorKSD882Y PNP
21
TSS-Sub500
Description
Reference Designator
Part Number
Qty
POWER/MAIN PCB
Q119
Q106
Q105
D110
D104
192-202b772y
192-991d669a
192-992b649t
197-00kb1405
197-101n4002
TransistorKSD772Y PNP
1
1
1
1
1
TransistorHI-SINCERITY HSD669A NPN
Transistor HSB649T PNP
diode 4A500V KBL405 BRIDGE
diode IN4002
Miscellaneous
162-10202001
171-udhss124d
175-1c07v01
175-1d02v01
175-1d03v01
193-3m2520
wire 26AWC 1007 200mm RED
relay 5A 24V UDH-SS124D
wire connector 7PIN PITCH=2.5mm
wire connector 2PIN PITCH=3.96mm
wire connector 3PIN PITCH=3.96mm
insulator TO-3P 25x20mm
1
1
1
1
1
2
RY101
P101
P102
P103
for Q107,108
LIMITER PCB
R301,303,304,308,309,314,340,344
R302
R310,312
R341
R305
R342,343
R307
R311,313
R306
C305,306
C302,303
C301,340
C304
Q301,302
D301,302
110-16103j26
110-16183j26
110-16223j26
110-16273j26
110-16333j26
110-16472j26
110-16474j26
110-16751j26
110-16755j26
130-2f104z503
132-103j503
135-3226m50
135-3476m25
192-027c1815gr
197-031n4148
162-50289001
175-9f40hr2
Resistor 10K 1/6W ±5% CF 26mm
Resistor 18K 1/6W ±5% CF 26mm
Resistor 22K 1/6W ±5% CF 26mm
Resistor 27K 1/6W ±5% CF 26mm
Resistor 33K 1/6W ±5% CF 26mm
Resistor 4.7K 1/6W ±5% CF 26mm
Resistor 470K 1/6W ±5% CF 26mm
Resistor 750Ω 1/6W ±5% CF 26mm
Resistor 7.5k 1/6W ±5% CF 26mm
disc Capacitor 0.1u 50V +80/-20%
mylar Capacitor 0.01U 50V ± 5%
electrolytic 22U 50V ± 20%
electrolytic 47U 25V ± 20%
Transistor 2SC1815gr NPN
diode 100mA 75V SIGNAL 1N4148
CABLE ASS'Y wire's 280mm AWG26 WHT
coupling 40PIN PITCH=2.54mm HR2*40
I .C TL074cm st QUAD OP-AMP
8
1
2
1
1
2
1
2
1
2
2
2
1
2
2
1
0.15
1
P301
U301
190-16tl074cn
MISCELLANEOUS/MECHANICAL
123-14j70d
Ferrite Core U-16.3*8.2*13(J70)+CASE
1
1
1
1
1
1
1
1
1
1
C001
T1
130-3f472md00
150-e8604107
152-u602015
154-u25006t0
155-520020
162-10082007
162-50652003
176-wjcel
disc Capacitor 4700P 400V ± 20%
Power Transformer EI-86 60HZ 120V TT086996580
LineCord SVT FT-2 6FT
Fuse 2.5A 250V 20mm
Fuse Holder R3-11
WIRE RED 18AWG 80mm 8mm#1015
WIRE 650mm RED=205# 0.5T BLK=110# 0.5T
wire connector Pin CE-1
SW100
180-prf1003S
switch ROCK RF-1003-BB2-OHA POWER
176-wjce1
wire connector pin CE-1
1
4
4
6
2
8
4
2
1
2
350-EM04012D024 4￠*12 wood screw black
351-HM04016A218 M4*16 machine screw black
351-AM03008A079 M3*8 machine screw black
352-AM03010D065 ￠3*10 P type tapping screw black
352-AM03008D040 ￠3*8 B type tapping screw black
354-GM04002
362-FE-00013
311-ABS-00028
335-NYL-00002
M4 nut black
PCB support L TYPE t=1.6mmS.P.C.C 89*9*1.6T
plastic knob 46077-W soft matetial P.V.C. LEVEL
wire clip 4K-4 NO-BB
22
TSS-Sub500
Description
Reference Designator
Part Number
Qty
MISCELLANEOUS/MECHANICAL
333-EVA-00783
333-EVA-00807
EVA W 198*12*2.0T
EVA L 274*12*2.0T
2
2
2
2
4
1
1
1
1
1
333-EVA-00826 EVA W 198*12*1.0T
333-EVA-00835
320-RUB-00033
337-CU-00101
306-ABS-00177
162-50552003
EVA L 274*12*1.0T
rubber foot pad 25*21*4t
copper foil 65L*50W
rear Plastic housing 198*298*102mm
WIRE UL1007 #16 550mm#110/#205 0.5T
302-AL-05048-0BAE rear board 300*200*2.5T black(RoHS)
323-AL-00106-0BB HEAT SINK 117.5*71.5*25 anode is black
23
|
