Owner’s Manual
Installation and Operation
Models:
Cosmo-I30
Cosmo-I35
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
WARNING
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• DO NOT store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
• What to do if you smell gas
- DO NOT try to light any appliance.
High temperatures may ignite clothing or other flammable
materials.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
• Keep clothing, furniture, draperies and other flammable
materials away.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppli-
er’s instructions.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
- If you cannot reach your gas supplier, call
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
ACO detector shall be installed in the room where the appliance
in installed.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions
and the manufactured home construction and safety standard,
Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
1
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 4
7 Installation Preparation
A. Inspection and Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . 20
B. Flue Damper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
C. Gas Line. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
D. Fireplace Conversion Notice . . . . . . . . . . . . . . . . . . . . . . 20
E. Electrical Outlet Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1 Listing and Code Approvals
A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
B. Glass Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . . 6
E. Non-Combustible Materials Specification. . . . . . . . . . . . . . 6
F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 6
G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
8 Installing Vent Pipe and Appliance
A. Vent Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
B. Venting Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
C. Connecting Vent Pipe. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
D. Placing, Securing and Leveling the Appliance . . . . . . . . . 22
E. Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
F. Installing Adaptor and Termination Cap . . . . . . . . . . . . . . 23
User Guide
2 Operating Instructions
A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
C. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
D. Decorative Doors, Fronts and Surrounds. . . . . . . . . . . . . . 8
E. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
F. Remote Controls, Wall Controls and Wall Switches. . . . . . 8
G. IPI Battery Tray/Battery Installation . . . . . . . . . . . . . . . . . . 8
H. Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . . . 9
I. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . 9
J. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 10
K. After Appliance is Lit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
L. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 11
9 Gas Information
A. Fuel Conversion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . 24
10 Electrical Information
A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
B. IntelliFire Plus™ Ignition System Wiring . . . . . . . . . . . . . 25
C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 26
D. Fan Wiring with Remote. . . . . . . . . . . . . . . . . . . . . . . . . . 27
E. Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . . 27
3 Maintenance and Service
11 Finishing
A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 12
B. Maintenance Tasks-Service Technician . . . . . . . . . . . . . . 13
A. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 28
12 Appliance Setup
Installer Guide
A. Remove Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 29
B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 29
C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
E. Glass Panel Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . 29
F. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
G. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4 Getting Started
A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 15
B. Design and Installation Considerations . . . . . . . . . . . . . . 16
C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 16
D. Inspect Appliance and Components. . . . . . . . . . . . . . . . . 16
5 Fireplace Size Requirements
13 Troubleshooting
A. Minimum Fireplace Opening . . . . . . . . . . . . . . . . . . . . . . 17
B. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 18
A. IntelliFire Plus™ Ignition System . . . . . . . . . . . . . . . . . . . 31
14 Reference Materials
6 Termination Locations
A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 33
B. Vent Kits Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
C. Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 19
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
3
B. Limited Lifetime Warranty
4
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
B. Limited Lifetime Warranty (continued)
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
5
Listing and Code Approvals
1
A. Appliance Certification
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
MODELS: Cosmo-I30, Cosmo-I35
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Vented Gas Fireplace Heater
STANDARD: ANSI Z21.88-2009 CSA 2.33-2009
Vented Gas Fireplace Heaters
When installing above 2000 feet elevation:
• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burn-
ing Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
Check with your local gas utility to determine proper
orifice size.
E. Non-Combustible Materials Specification
Heat & Glo gas inserts are designed for installations into
solid fuel masonry or factory built fireplaces that have been
installed in accordance with the National, Provincial, State
and local building codes. Fireplaces are to be constructed
of non-combustible materials and, in the absence of local
or regional codes, meet criteria of NFPA211. No additional
outside air source is required.
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750 ºC and UL763 shall be
considered non-combustible materials.
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed pa-
per, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemen-
tal room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
G. Electrical Codes
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA
70-latest edition or the Canadian Electric Code CSA
C22.1.
B. Glass Specifications
This appliance is equipped with 5 mm ceramic glass. Re-
place glass only with 5 mm ceramic glass. Please contact
your dealer for replacement glass.
• A 120 VAC circuit for this product must be protected with
ground-fault circuit-interrupter protection, in compliance
with the applicable electrical codes, when it is installed in
locations such as in bathrooms or near sinks.
C. BTU Specifications
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orifice
Size
(DMS)
Models
(U.S. or Canada)
US
23,000
20,700
28,000
25,200
23,000
20,700
27,500
24,750
13,500
12,150
15,500
13,950
13,500
12,150
14,500
14,000
42
43
38
39
54
55
52
53
(0-2000 FT)
Cosmo-I30 (NG)
Cosmo-I35 (NG)
Cosmo-I30 (LP)
Cosmo-I35 (LP)
CANADA
(2000-4500 FT)
US
(0-2000 FT)
CANADA
(2000-4500 FT)
US
(0-2000 FT)
CANADA
(2000-4500 FT)
US
(0-2000 FT)
CANADA
(2000-4500 FT)
6
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
User Guide
Operating Instructions
2
• Install a switch lock or a wall/remote control with child
protection lockout feature.
A. Gas Fireplace Safety
• Keep remote controls out of reach of children.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
• Never leave children alone near a hot fireplace, whether
operating or cooling down.
• Teach children to NEVER touch the fireplace.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• Consider not using the fireplace when children will be
present.
Contact your dealer for more information, or visit: www.
hpba.org/safety-information.
• CAREFULLY SUPERVISE children in same room as
fireplace.
To prevent unintended operation when not using your fire-
place for an extended period of time (summer months,
vacation/trips, etc):
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
• Remove batteries from remote controls.
• Turn off wall controls.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
B. Your Fireplace
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
WARNING! DO NOT operate fireplace before read-
ing and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
WARNING! Choking Hazard! Keep media out of reach
of children.
If you expect that small children or vulnerable adults may
come into contact with this fireplace, the following precau-
tions are recommended:
• Install a physical barrier such as:
- A decorative firescreen.
- Adjustable safety gate.
APPLIANCE INSTALLED IN EXISTING
SOLID FUEL FIREPLACE
DECORATIVE DOORS
(NOT SHOWN)
SECTION 2.D.
FIXED GLASS ASSEMBLY
(NOT SHOWN)
MANTEL
SECTION
5.B AND
11.A
SECTION 12.F.
HEARTH
CLEAR SPACE
SECTION 2.C.
Figure 2.1 General Operating Parts
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
7
C. Clear Space
E. Fixed Glass Assembly
WARNING! DO NOT place combustible objects in front
of the fireplace or block louvers. High temperatures may
start a fire. See Figure 2.2.
See Section 12.F.
F. Remote Controls, Wall Controls and Wall
Switches
Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.
Follow the instructions supplied with the control installed
to operate your fireplace:
For safety:
• Install a switch lock or a wall/remote control with child
protection lockout feature.
APPLIANCE INSTALLED IN EXISTING
SOLID FUEL FIREPLACE
• Keep remote controls out of reach of children.
See your dealer if you have questions.
G. IPI Battery Tray/Battery Installation
The IntelliFire PlusTM system has a battery backup option.
Battery longevity and performance will be affected by the
service temperatures of this appliance.
NOTICE: Batteries should only be used as a power source
in the event of an emergency such as an outage.
Figure 2.2 Clear Space
D. Decorative Doors, Fronts and Surrounds
WARNING! Risk of Fire! Install ONLY doors, fronts or
surrounds approved by Hearth & Home Technologies.
Unapproved doors or fronts may cause appliance to over-
heat.
This appliance has been supplied with an integral
barrier to prevent direct contact with the fixed glass
panel. DO NOT operate the appliance with the barrier
removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
For more information refer to the instructions supplied with
your decorative door or front.
8
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
H. Control Module Operation
1. The control module has an ON/OFF/REMOTE selector
switch that must be set. See Figure 2.3.
OFF Position: Appliance will ignore all power inputs and
will not respond to any commands from a wall switch or
remote. The unit should be in the OFF position during
installation, service, battery installation, fuel conversion,
and in the event that the control goes into LOCK-OUT
mode as a result of an error code.
SELECTOR
SWITCH
ON Position: Appliance will ignite and run continuously
in the HI flame setting, with no adjustment in flame
output. This mode of operation is primarily used for
initial installation or power outage operation with battery
backup.
STATUS INDICATOR LED
REMOTE Position: Appliance will initiate commands
from an optional wired wall switch and/or the wireless
remote (RC300).
FLAME HI/LO SWITCH
NG/LP SETTING
Figure 2.3 Control Module
2. If using a wired wall switch with the module in REMOTE
mode, the flame output can be adjusted with the HI/LO
selector switch on the module. See Figure 2.3. Note
that the flame HI/LO selector switch will become inactive
once an optional remote control (RC200/RC300) is
programmed to the control module. Note that the control
module will always ignite the fireplace on HI and remain
so for the initial 10 seconds of operation. If the HI/LO
is switched to the LO position, the flame output will
automatically drop to the lowest setting after the flame
has been established for 10 sec. After this 10 second
period, the flame can be adjusted from HI to LO with
the switch.
•
Start the appliance.
WARNING! Risk of Explosion! DO NOT press the mod-
ule reset switch more than one time within a five minute
time period. Gas may accumulate in firebox. Call a quali-
fied service technician.
I. Before Lighting Fireplace
3. The control module has safety feature that automatically
shuts down the fireplace after 9 hours of continuous
operation without receiving a command from the RC300
remote.
Before operating this fireplace for the first time, have a
qualified technician:
• Verify all shipping materials have been removed from
inside and/or underneath the firebox.
4. If you intend to use both an optional wired wall switch
and the RC300 remote control to operate your fireplace,
the wall switch will override any commands given by
the remote.
• Review proper placement of logs, ember material and/or
other decorative materials.
• Check the wiring.
5. Module Reset
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
This module may lock-out under certain conditions.
When this occurs, the appliance will not ignite or
respond to commands. The module will go into
lock-out mode by emitting three audible beeps, then
continuously displaying a RED/GREEN error code at
its status indicator LED.
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
WARNING! Risk of Fire/Asphyxiation! DO NOT oper-
ate fireplace with fixed glass assembly removed.
•
Check battery tray. Remove batteries if installed.
Batteries should only be installed for use during power
outages. See Section G.
• An Intellifire Plus™ ignition system is standard with this
appliance.
•
•
•
Locate the module selector switch. (See Figure 2.3).
Set the module selector switch to the OFF position.
Wait five (5) minutes to allow possible accumulated gas
to clear.
•
Set the module selector switch to ON or REMOTE
position.
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
9
J. Lighting Instructions (IPI)
The IPI system may be operated with four AA-cell batteries. When using batteries, unplug the transformer. To prolong bat-
tery life, remove them when using the transformer.
FOR YOUR SAFETY
LIGHTING
READ BEFORE LIGHTING
INSTRUCTIONS (IPI)
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
1. This appliance is equipped with an ignition
device which automatically lights the burner.
DO NOT try to light the burner by hand.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
A. This appliance is equipped with an
intermittent pilot ignition (IPI) device
which automatically lights the burn-
er. DO NOT try to light the burner by
hand.
GAS
VALVE
• If you cannot reach your gas sup-
plier, call the fire department.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
C. DO NOT use this appliance if any
part has been under water. Imme-
diately call a qualified service tech-
nician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
2. Wait five (5) minutes to clear out any gas.
Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” in the Safety
Information located on the left side of this la-
bel. If you do not smell gas, go to next step.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
3. To light the burner:
• DO NOT touch any electric switch; do
not use any phone in your building.
Equipped with wall switch: Turn ON/OFF switch
to ON.
Equipped with remote or wall control: Press
ON or FLAME button.
WARNING: CAUTION:
Equipped with thermostat: Set temperature to
desired setting.
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gaso-
line and other liquids having flammable
vapors away.
DO NOT CONNECT LINE VOLT-
AGE (110/120 VAC OR 220/240
VAC) TO THE CONTROL VALVE.
4. If the appliance does not light after three tries,
call your service technician or gas supplier.
Improper installation, adjustment, al-
teration, service or maintenance can
cause injury or property damage. Re-
fer to the owner’s information manual
provided with this appliance.
TO TURN OFF
GAS TO APPLIANCE
1. Equipped with wall switch: Turn ON/OFF switch
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
to OFF.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
Equipped with remote or wall control: Press
OFF button.
NOT FOR USE
WITH SOLID FUEL
Equipped with thermostat: Set temperature to
lowest setting.
If not installed, operated, and main- For use with natural gas and propane.
tained in accordance with the manufac- A conversion kit, as supplied by the
turer’s instructions, this product could manufacturer, shall be used to convert
expose you to substances in fuel or this appliance to the alternate fuel.
2. Service technician should turn off electric
power to the control when performing service.
fuel combustion which are known to the
State of California to cause cancer, birth
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
593-913G
defects, or other reproductive harm.
For assistance or additional informa-
Keep burner and control compartment
tion, consult a qualified installer, ser-
clean. See installation and operating
vice agency or the gas supplier.
instructions accompanying appliance.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
Final inspection by
10
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
K. After Appliance is Lit
Initial Break-in Procedure
• The appliance should be run three to four hours
continuously on high.
• Turn the appliance off and allow it to completely cool.
• Remove fixed glass assembly. See Section 12.F.
• Clean fixed glass assembly. See Section 3.
• Replace the fixed glass assembly and run continuously
on high an additional 9 hours.
This cures the materials used to manufacture the fire-
place.
NOTICE! Open windows for air circulation during ap-
pliance break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
L. Frequently Asked Questions
ISSUE
SOLUTIONS
This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.
Condensation on the glass
This is a result of normal operation and the flames will begin to yellow as the appliance is al-
lowed to burn for 20 to 40 minutes.
Blue flames
When first operated, this appliance may release an odor for the first several hours. This is caused
by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may
also be released from finishing materials and adhesives used around the appliance.
Odor from appliance
Film on the glass
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Metallic noise
In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is
turned off. Some optional control systems available with IPI models may allow pilot flame to
remain lit.
Is it normal to see the pilot flame burn
continually?
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
11
Maintenance and Service
3
Doors, Surrounds, Fronts
Any safety screen or guard removed for servicing must be
replaced prior to operating the appliance.
Frequency: Annually
By: Homeowner
When properly maintained, your appliance will give you
many years of trouble-free service. We recommend an-
nual service by a qualified technician.
Tools needed: Protective gloves, stable work surface
• Assess condition of screen and replace as necessary.
A. Maintenance Tasks-Homeowner
• Inspect for scratches, dents or other damage and repair
as necessary.
Installation and repair should be done by a qualified techni-
cian only. The appliance should be inspected before use
and at least annually by a professional service person.
• Check that louvers are not blocked.
• Vacuum or dust surfaces.
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service ap-
pointment.
Remote Control
Frequency: Seasonally
By: Homeowner
More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner
and circulating air passageway of the appliance must be
kept clean.
Tools needed: Replacement batteries and remote con-
trol instructions.
• Locate remote control transmitter and receiver.
• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.
CAUTION! Risk of Burns! The appliance should be
turned off and cooled before servicing.
Glass Cleaning
Frequency: Seasonally
By: Homeowner
• Place batteries as needed in remote transmitters and
battery-powered receivers.
• Place remote control out of reach of children.
Tools Needed: Protective gloves, glass cleaner, drop
cloth and a stable work surface.
If not using your fireplace for an extended period of time
(summer months, vacations/trips, etc), to prevent unin-
tended operation:
CAUTION! Handle fixed glass assembly with care.
Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• Remove batteries from remote controls.
• DO NOT clean glass while it is hot
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth
on a flat, stable surface.
Note: Fixed glass assembly and gasketing may have res-
idue that can stain carpeting or floor surfaces.
• Remove door or decorative front from appliance and set
aside on work surface.
• See Section 12.F for instructions to remove fixed glass
assembly.
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
• Carefully set fixed glass assembly in place on appliance.
Hold glass in place with one hand and secure glass
latches with the other hand.
• Reinstall door or decorative front.
12
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
Venting
Firebox
Frequency: Seasonally
By: Homeowner
Frequency: Annually
By: Service Technician
Tools needed: Protective gloves and safety glasses.
Tools needed: Protective gloves, sandpaper, steel wool,
cloths, mineral spirits, primer and touch-up paint.
• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.
• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.
• Verify termination cap clearance to subsequent construc-
tion (building additions, decks, fences, or sheds). See
Section 6.
• Replace appliance if firebox has been perforated.
Control Compartment and Firebox Top
Frequency: Annually
• Inspect for corrosion or separation.
By: Service Technician
• Verify weather stripping, sealing and flashing remains
Tools needed: Protective gloves, vacuum cleaner, dust
intact.
cloths
• Inspect draft shield to verify it is not damaged or missing.
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.
B. Maintenance Tasks-Service Technician
The following tasks must be performed by a qualified
technician.
• Remove all foreign objects.
• Verify unobstructed air circulation.
Gasket Seal and Glass Assembly Inspection
Frequency: Annually
By: Service Technician
Tools needed: Protective gloves, drop cloth and a stable
work surface.
• Inspect gasket seal and its condition.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
13
Burner Ignition and Operation
Frequency: Annually
By: Service Technician
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
• Verify burner is properly secured and aligned with pilot
or igniter.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
• Verify batteries have been removed from battery back-up
IPI systems to prevent premature battery failure or
leaking. For optimal battery life, locate the battery
pack outside of the control cavity on the hearth. This
placement will reduce the chances of overheating the
batteries during extended burns which could result in
reduced battery life or degradation.
Figure 3.1 IPI Pilot Flame Patterns
• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.
• Inspect for lifting or other flame problems.
• Verify air shutter setting is correct. See Section 12.G for
required air shutter setting. Verify air shutter is clear of
dust and debris.
• Inspect orifice for soot, dirt and corrosion. Verify orifice
size is correct. See Service Parts List for proper orifice
sizing.
• Verify manifold and inlet pressures. Adjust regulator as
required.
• Inspect pilot flame pattern and strength. See Figure 3.1
for proper pilot flame pattern. Clean or replace orifice
spud as necessary.
• Inspect thermocouple/thermopile or IPI flame sensing rod
for soot, corrosion and deterioration. Clean with emery
cloth or replace as required.
• Verify that there is not a short in flame sense circuit by
checking continuity between pilot hood and flame sense
rod. Replace pilot as necessary. (IPI only)
14
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
Installer Guide
Getting Started
4
A. Typical Appliance System
NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual
VERTICAL TERMINATION CAP
(SECTION 8.F)
VENT PIPE
(SECTION 8)
3 INCH FLEX LINERS
(SECTION 8)
MANTEL AND MANTEL LEG
SECTION 5.B AND 11.A
SURROUND OR FRONT
NOT SHOWN
SECTION 2.D AND 8.D.
HEARTH EXTENSION
GAS LINE (SECTION 9)
ACCESS THROUGH EXISTING
MASONRY OR WOODBURNING
FIREPLACE
Figure 4.1 Typical System
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
15
B. Design and Installation Considerations
D. Inspect Appliance and Components
Heat & Glo gas inserts are designed for installations into
solid fuel masonry or factory built fireplaces that have
been installed in accordance with the National, Provin-
cial, State and local building codes. Fireplaces are to be
constructed of non-combustible materials and, in the ab-
sence of local or regional codes, meet criteria of NFPA
211. No additional outside air source is required.
• Carefully remove the appliance and components from
the packaging.
• The vent system components and decorative doors and
fronts may be shipped in separate packages.
• If packaged separately, the log set and appliance grate
must be installed.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
Installation MUST comply with local, regional, state and na-
tional codes and regulations. Consult insurance carrier, local
building inspector, fire officials or authorities having jurisdic-
tion over restrictions, installation inspection and permits.
• Read all of the instructions before starting the instal-
lation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
Prior to installing the gas insert:
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, in-
complete or substitute components. Keep appliance dry.
• Have the chimney and adjacent structure inspected
and cleaned by qualified professionals. Hearth & Home
Technologies recommends that NFI or CSIA certified
professionals, or technicians under the direction of certi-
fied professionals, conduct a minimum of a NFPA 211
Level 2 inspection of the chimney.
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
• Replace component parts of the chimney and fireplace
as specified by the professionals.
• Installation and use of any damaged appliance or vent
system component.
• Ensure combustible mantel and surround clearances
comply with applicable codes and regulations for solid-
fuel fireplaces. In the absence of local or regional codes,
refer to NFPA 211.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
• Ensure all joints are properly engaged and the chimney
is properly secured.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
• Minimum fireplace size. See Section 5.A.
• Gas supply piping requirements.
• Electrical wiring requirements.
• Finishing details.
Any such action may cause a fire hazard.
WARNING! Risk of Fire,/Explosion/Electric Shock!
DO NOT use this appliance if any part has been under
water. Call a qualified technician to inspect the appliance
and to replace any part of the control system and/or gas
control which has been under water.
• Whether optional accessories—devices such as a wall
switch or remote control—are desired.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified
technician, service agency or your dealer.
C. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Tape measure
Pliers
Framing material
Flat blade screwdriver
Phillips screwdriver
Framing square
Hammer
Gloves
Voltmeter
Plumb line
Level
Electric drill and bits (1/4 in.)
Safety glasses
Reciprocating saw
Manometer
Noncorrosive leak check solution
1/2 - 3/4 inch length, #6 or #8 Self-drilling screws
Caulking material (300º F minimum continuous exposure
rating)
Stove cement (1200ºF or higher continuous exposure
rating)
16
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
Fireplace Size Requirements
5
from the factory built firebox if attached with mechanical
A. Minimum Fireplace Opening
fasteners.
Minimum fireplace opening requirements for a standard 3/4
inch deep surround are shown in Figure 5.1. For smaller
openings, an optional 1-1/2 inch deep surround is available
and dimensions are shown in Figure 5.2.
• The metal floor of the solid fuel firebox may be removed to
facilitate the installation of the insert. The appliance may
not be placed directly on the base of the outer wrap, a 1/4
inch airspace must be provided between the insert and
the floor of the outer wrap. Use the levelling legs to raise
the insert a minimum of 1/4 inch. The original fireplace
may never be returned to solid fuel in this condition.
The sidewalls and top structure of the firebox may not
be altered with the exception of removable baffles and
dampers.
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be locat-
ed out of traffic and away from furniture and draperies.
• The firebrick (refractory), glass doors, screen rails, screen
mesh and log grates can be removed from a factory
built firebox in order to gain minimum gas insert opening
requirements.
• Cutting of any sheet metal parts of the fireplace in which
the gas fireplace insert is to be installed is prohibited,
except the floor as tested for and as noted above.
• Any smoke shelves, shields and baffles may be removed
TOP VIEW
FRONT VIEW
SIDE VIEW
C
A
D
E
I
F
G
H
B
MINIMUM FIREPLACE SIZE
COSMO-I35
COSMO-I30
Location
Inches
23-1/2
34-5/8
31-9/16
15-11/16
24
Millimeters
597
Inches
20-1/4
30-1/2
27-7/16
12-13/16
20-1/2
17-5/8
14-3/4
9-1/2
Millimeters
514
A
B
Rear Width
Front Width
879
775
C
Glass Opening Width
Glass Opening Height
Height-Front
802
697
D
398
325
E
610
521
F
Height-Rear
21-1/16
16
535
448
G**
H
Unit Depth
406
375
Venting Depth
10-1/2
267
241
Height to Top of
Glass Frame
I
22
559
18-1/4
464
* Note: If exhaust collar on insert and fireplace damper do not line up, add 4 inches (102 mm) to minimum
fireplace height for bends in vent pipe.
**Unit depth is measured to the back of the surround to give the depth needed for installation.
In addition to these dimensions, also reference Clearances and Mantel Projections (Section 5.B).
Figure 5.1 Fireplace Opening
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
17
SIDE VIEW
TOP VIEW
1-1/2 IN.
BD
AD
CD
SURROUND
APPLIANCE
SURROUND
APPLIANCE
MINIMUM FIREPLACE SIZE
COSMO-I35
COSMO-I30
Location
Inches
33-3/16
15-1/16
22-9/16
Millimeters
843
Inches
29-1/16
13-7/8
Millimeters
738
AD
BD
CD
Alternate Unit Width
Alternate Unit Depth
Alternate Unit Height
383
352
573
19-1/16
484
* Note: If exhaust collar on insert and fireplace damper do not line up, add 4 inches (102 mm) to minimum
fireplace height for bends in vent pipe.
Figure 5.2 Fireplace Opening - Deep Surround
B. Mantel and Wall Projections
EXISTING NON-COMBUSTIBLE FACING
WARNING! Risk of Fire! Comply with all minimum clear-
ances to combustibles as specified. Framing or finishing
material closer than the minimums listed must be construct-
ed entirely of noncombustible materials (i.e., steel studs,
concrete board, etc).
12 IN. MAX.
Clearance to combustible material under the insert is 1/4
inch (6 mm). Clearance from top of fireplace opening for
combustibles extending 12 inches max. is 12 inches.
• Use leveling legs to raise insert minimum 1/4 inch (6 mm)
above combustible material or outer wrap of factory built
firebox.
12 IN. MIN.
Combustible facings must not extend behind the insert
surround. For non-combustible material specifications
refer to section 1.E.
Figure 5.3 Mantel Clearances
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
18
Termination Locations
6
A. Vent Termination Minimum Clearances
A
B
6 in. (minimum) up to 20 in.
152 mm/508 mm
18 in. minimum
457 mm
WARNING
20 in. and over
0 in. minimum
Fire Risk.
Gas, Wood or Fuel Oil
Termination Cap
Maintain vent clearance to combustibles as
specified.
• DO NOT pack air space with insulation or
other materials.
B
Failure to keep insulation or other materials
away from vent pipe may cause fire.
A *
HORIZONTAL
OVERHANG
Gas
Termination
Cap **
2 FT.
20 INCHES MIN.
VERTICAL
MIN.
WALL
LOWEST
DISCHARGE
OPENING
GAS DIRECT VENT
TERMINATION CAP
X
*
If using decorative cap cover(s), this distance may need to be
increased. Refer to the installation instructions supplied with the
decorative cap cover.
12
ROOF PITCH
IS X/ 12
In a staggered installation with both gas and wood or fuel oil
terminations, the wood or fuel oil termination cap must be
higher than the gas termination cap
**
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Figure 6.2 Staggered Termination Caps
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12.................................................1.25*
Over 7/12 to 8/12.................................................1.5*
Over 8/12 to 9/12.................................................2.0*
Over 9/12 to 10/12...............................................2.5
Over 10/12 to 11/12.............................................3.25
Over 11/12 to 12/12.............................................4.0
Over 12/12 to 14/12.............................................5.0
Over 14/12 to 16/12.............................................6.0
Over 16/12 to 18/12.............................................7.0
Over 18/12 to 20/12.............................................7.5
Over 20/12 to 21/12.............................................8.0
* 3 foot minimum in snow regions
Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
19
Installation Preparation
7
Prepare the existing solid fuel masonry or factory built
non-combustible firebox for installation.
D. Fireplace Conversion Notice
Permanently attach the label with the following warning to
the inside lower back of the fireplace firebox into which the
insert is being installed. Silicone or mechanical fasteners
may be required to properly secure the label.
A. Inspection and Cleaning
Prior to installing the gas insert:
• Have the chimney and adjacent structure inspected
and cleaned by qualified professionals. Hearth & Home
Technologies recommends that NFI or CSIA certified
professionals, or technicians under the direction of certi-
fied professionals, conduct a minimum of a NFPA 211
Level 2 inspection of the chimney.
WARNING! Risk of Fire! This fireplace has been con-
verted for use with a gas fireplace insert only and cannot
be used for burning wood or solid fuels unless all original
parts have been replaced, and the fireplace re-approved
by the authority having jurisdiction.
• Replace component parts of the chimney and fireplace
as specified by the professionals.
E. Electrical Outlet Box
An outlet box may be installed in a bottom back corner of
the existing solid fuel masonry or factory built fireplace to
power the appliance. Each insert ships standard with a
cord assembly to permit blowers or other optional acces-
sories to be used. The accessories plug into the new out-
let box or may be routed out onto the hearth to a nearby
outlet.
• Ensure all joints are properly engaged and the chimney
is properly secured.
• Ensure combustible mantel and surround clearances
comply with applicable codes and regulations for solid-
fuel fireplaces. In the absence of local or regional codes,
refer to NFPA 211.
• Ensure chimney is constructed of non-combustible
materials.
• Ensure chimney is clean and in good working order.
• Ensure that all chimney cleanouts fit properly to prevent
air leakage into chimney.
B. Flue Damper
Fully lock the solid fuel fireplace’s flue damper in the open
position, OR completely remove it.
C. Gas Line
Note: If the factory built fireplace has no gas access hole
provided, an access hole of 1 inch (25 mm) diameter or
less may be drilled through the lower sides or bottom of the
firebox in a proper workmanship - like manner. This access
hole must be plugged with non-combustible insulation after
the gas supply line has been installed.
• Install gas line into firebox cavity.
• Check local codes and gas line sizing requirements
following NFPA51. See Section 9.
• It is recommended that extra length of gas line be
installed within the existing wood burner or masonry
fireplace to allow removal of the insert for future servicing
needs.
20
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
Installing Vent Pipe and Appliance
8
A. Vent Limits
B. Venting Components
The abbreviations listed in this vent table key are used in
the vent diagrams.
CAUTION! Risk of Cuts/Abrasions/Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
Description
The vertical vent termination system installed on this model
includes:
Minimum Vertical Run Length 10 ft.
Maximum Vertical Run Length 50 ft.
• Flexible vent pipe for exhaust air (included with vent kit).
• One length of 3-inch flexible vent pipe for combustion
air (included with vent kit).
Horizontal venting is NOT allowed.
Vertical terminations are measured to top of chimney.
• One pipe-to-cap adaptor (included with vent kit).
• One vertical termination cap (included with vent kit).
This appliance is listed for use with LINK-DV systems
and components only. It is permissible to extend venting
above existing chimney (within specified maximum verti-
cal limits) using SL-D series or Dura Vent GS series 4 in.
x 6-5/8 in. gas direct-vent pipe. Connection is made us-
ing DV-46DVA-GK. The vent must be terminated with the
cap supplied with the LINK-series vent kit.
C. Connecting Vent Pipe
Reference instructions in the termination kit.
• Install the 3-inch flexible vent pipe(s) down through the
chimney.
WARNING! Risk of Fire/Explosion/Asphyxiation! Do
NOT connect this gas appliance to a chimney flue serving
a separate solid fuel or gas burning appliance.
• Secure the exhaust flexible vent pipe to the exhaust
starting collar on top of the appliance with three screws
and seal with stove cement rated for continuous
exposure to 1200ºF or higher. See Figure 8.1.
• May impair safe operation of this appliance or other
appliances connected to the flue.
• Vent this appliance directly outside.
• Use 3 screws to attach the section of inlet air vent to
the inlet collar on the collar slide plate and seal with
stove cement rated for continuous exposure to 1200ºF
or higher. See Figure 8.1. NOTE: The collar slide plate
may be removed from appliance to aid installation.
• Use separate vent system for this appliance.
CAUTION! ALL vent specifications MUST be followed.
This product is tested and listed to these specifications.
Appliance performance will suffer if specifications are not
followed.
TERMINATION
CAP
ADAPTER
INLET
COLLAR
EXHAUST
COLLAR
INLET AIR STARTING COLLAR
LOCKING TAB
EXHAUST
AIR
VENT PIPE
V = 10 FT. MINIMUM
50 FT. MAXIMUM
STARTING COLLAR BRACKET
EXHAUST STARTING COLLAR
HANDLE
INLET AIR
VENT PIPE
INLET AIR STARTING COLLAR
NOTE: TO ACHIEVE OPTIMUM PERFOR-
MANCE OF INSERT, MINIMIZE OR AVOID
BENDS IN EXHAUST VENT PIPE.
STARTING COLLAR BRACKET
EXHAUST STARTING COLLAR
Figure 8.1
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
21
WARNING! Risk of Fire! Only an approved Hearth &
Home Technologies surround may be used to cover inte-
gral grills on solid fuel burning fireplaces. No other com-
ponents such as shrouds, sheetmetal plates, etc., may be
used to seal off vents.
CUT AND BEND
FLASHING AS NEEDED
TO FIT CHIMNEY
WARNING! Risk of Explosion! Failure to position the
parts in accordance with these diagrams or failure to use
only parts specifically approved with this appliance may
result in property damage or personal injury.
SEALANT
ADHESIVE
WARNING! Risk of Explosion/Combustion Fumes!
Connect vent sections per installation instructions.
• Connect exhaust vent pipe ONLY to exhaust starting
collar and termination cap center collar.
• Connect inlet air vent ONLY to inlet air collar on appliance
and the termination cap inlet air collar.
• DO NOT allow vent to sag below connection point to
appliance.
Figure 8.2
• Trim chimney top plate to minimize excess overhang or
bend over flue tile (see Figure 8.2).
• Place 3/8 inch bead of 300º F silicone on flue tile top.
E. Remote Control
D. Placing, Securing and Leveling the Appli-
ance
If a remote control kit is used to control blower function,
the Auxiliary 300 module can only be placed in the control
cavity to the right of the control panel. See Figure 8.3.
• Install insert (without surround attached) into existing
fireplace while pulling collar slide plate forward.
• Install gas line into hole provided on insert side.
• If applicable install remote control wires into insert side
(see Section 8.E).
• Secure collar slide plate to appliance by placing locking
handle into position with locking tabs (see Figure 8.1)
and secure with #8 screw.
• Level the appliance from side to side and front to back. If
necessary, use the leveling legs included with the manual
bag to set each corner of the base.
• Position any excess flexible vent pipe back up into
chimney without sagging. Twist and push flex vent
together to shorten.
AUXILIARY 300 MODULE
• Install fiberglass insulation pieces to back face of
surround.
Figure 8.3 Location of AUX300 for Remote Control
Blower Function
• Attach surround. Follow instructions for surround
installation included with the front.
• Push insert into the opening so that it tightly overlaps
the fireplace opening.
22
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
CAUTION! Risk of Cuts/Abrasions/Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
F. Installing Adaptor and Termination Cap
For installation of termination cap see minimum vent
heights for various pitched roofs (see Figure 8.4) .
Damper Flashing Kit (Optional)
To install adaptor see Figure 8.5.
For use with LINK-DV30B or LINK-DV4-30B Liner Kit.
Note: Damper may have to be removed to use this kit.
• Run flex liners through 3 in. holes in damper flashing.
HORIZONTAL
OVERHANG
• Attach damper flashing to firebox roof with self tapping
screws included in kit.
2 FT.
20 INCHES MIN.
VERTICAL
MIN.
WALL
LOWEST
DISCHARGE
OPENING
CLASS A PIPE
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Roof Pitch
H (Min.) Ft.
Roof Pitch
H (Min.) Ft.
Over 11/12 to 12/12.......4.0
Over 12/12 to 14/12.......5.0
Over 14/12 to 16/12.......6.0
Over 16/12 to 18/12.......7.0
Over 18/12 to 20/12.......7.5
Over 20/12 to 21/12.......8.0
Flat to 6/12....................1.0*
Over 6/12 to 7/12........1.25*
Over 7/12 to 8/12..........1.5*
Over 8/12 to 9/12..........2.0*
Over 9/12 to 10/12........2.5*
Over 10/12 to 11/12.....3.25
Figure 8.5
* 3 foot minimum in snow regions
Figure 8.4 Minimum Height from Roof to Lowest Discharge
Opening
Note: The LINK-DV4-30B
To help eliminate cold air drafts, it may be necessary to place non-
system REQUIRES this insulation.
combustible insulation around the flues as they go though the damper.
Masonry
Factory Built
Wood Burning
LINK-DV30B
Installation
LINK-DV4-30B
Installation
TERMINATION
CAP
OPTIONAL LINK-ZC-ADPB
FOR USE WITH CLASS A
WOODBURNING PIPE
EXHAUST
AIR
EXHAUST
AIR
VENT PIPE
VENT PIPE
OR
WARNING:
DO NOT BLOCK
THIS PIPE END!
Note: Untwist the
pipe while extend-
ing it, to achieve full
30’ length.
INLET AIR
VENT PIPE
INLET AIR
VENT PIPE
Remove 18 inch x 18 inch flashing on cap by removing 3
screws. Connect both the LINK-ZC-ADPB to Class A Pipe
and the termination cap to the LINK-ZC-ADPB with the
self tapping screws provided.
Figure 8.6
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
23
Gas Information
9
A. Fuel Conversion
C. Gas Connection
• Make sure the appliance is compatible with available gas
types.
• Refer to Reference Section 15 for location of gas line
access in appliance.
• Conversions must be made by a qualified technician
(NFI certified or factory-trained) using Hearth & Home
Technologies specified and approved parts.
• Gas line may be run through knockout(s) provided.
• The gap between supply piping and gas access hole may
be caulked with caulk with a minimum of 300ºF continuous
exposure rating or stuffed with non-combustible, unfaced
insulation to prevent cold air infiltration.
B. Gas Pressure
• Optimum appliance performance requires proper input
pressures.
• Ensure that gas line does not come in contact with outer
wrap of the appliance. Follow local codes.
• Gas line sizing requirements will be determined in ANSI
Z223.1 National Fuel Gas Code in the USA and CAN/
CGA B149 in Canada.
• Pipe incoming gas line into valve compartment.
• Connect incoming gas line to the 1/2 in. (13 mm)
connection on manual shutoff valve.
• Pressure requirements are:
WARNING! Risk of Fire/Explosion! Support control
when attaching pipe to prevent bending gas line.
Gas Pressure
Minimum inlet pressure
Maximum inlet pressure
Manifold pressure
Natural Gas
5.0 in. w.c.
10.0 in. w.c.
3.5 in. w.c.
Propane
11.0 in. w.c.
13.0 in. w.c.
10.0 in. w.c.
• A small amount of air will be in the gas supply lines.
WARNING! Risk of Fire/Explosion! Gas build-up during
line purge could ignite.
• Purge should be performed by technician certified by
NFI or factory-trained.
• Ensure adequate ventilation.
WARNING! Risk of Fire/Explosion! High pressure will
damage valve. Low pressure may cause explosion.
• Ensure there are no ignition sources such as sparks
or open flames.
• Verify inlet pressures. Verify minimum pressures when
other household gas appliances are operating.
Light the appliance. It will take a short time for air to purge
from lines. When purging is complete the appliance will
light and operate normally.
• Install regulator upstream of valve if line pressure is
greater than 1/2 psig.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all fittings and connections with a non-corrosive
commercially available leak-check solution. DO NOT use
open flame. Fittings and connections could have loos-
ened during shipping and handling.
WARNING
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
WARNING! Risk of Fire! DO NOT change valve settings.
This valve has been preset at the factory.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
Note: Have the gas supply line installed in accordance with
local codes, if any. If not, follow ANSI 223.1. Installation
should be done by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth
of Massachusetts installation must be performed by a
licensed plumber or gas fitter).
When installing above 2000 feet elevation:
• In the USA: Reduce burner orifice 4% for each 1000 feet
above 2000 feet.
• In the CANADA: Reduce burner orifice 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Note: A listed (and Commonwealth of Massachusetts ap-
proved) 1/2 inch (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 inch
(13 mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
24
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
Electrical Information
10
B. IntelliFire Plus™ Ignition System Wiring
A. Wiring Requirements
• Wire an outlet box (120VAC) in the bottom back corner of
the existing solid fuel masonry or factory built fireplace to
plug in the cord assembly. The supplied cord assembly
may also be routed out onto the hearth to a nearby outlet.
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
WARNING! Risk of Shock or Explosion! DO NOT wire
IPI controlled appliance junction box to a switched circuit.
Incorrect wiring will override IPI safety lockout.
• This appliance comes standard with a 120 VAC cord
assembly which has a female plug in to accommodate
all control options and accessories. See Figure 10.1.
This is required for proper operation of the appliance
(IntelliFire Ignition). An outlet box may be installed in a
bottom back corner of the existing solid fuel masonry or
factory built fireplace to plug in the cord assembly, or the
supplied power cord may be routed out onto the hearth
to a nearby outlet.
• Refer to Figure 10.1, IPI Wiring Diagram.
• This appliance is equipped with an IntelliFire Plus™
control valve which operates on a 6 volt/1.5 AMP
system.
• Plug the 6 volt transformer plug into the cord assembly to
supply power to the insert OR install 4 AA cell batteries
(not included) into the battery pack before use.
• A 120 VAC circuit for this product must be protected with
ground-fault circuit-interrupter protection, in compliance
with the applicable electrical codes, when it is installed in
locations such as in bathrooms or near sinks.
ON/OFF Switch
• An ON/OFF switch is included with the appliance
surround and should be attached to surround/facing.
(See Installation instructions for remote control/fronts).
• Low voltage and 120 VAC voltage cannot be shared
within the same wall box.
• If desired an additional wall switch or thermostat may
be added to system as shown in Figure 10.1.
WARNING! Risk of Shock or Explosion! DO NOT wire
120V to the valve or to the appliance wall switch. Incor-
rect wiring will damage controls.
• An IntelliFire Plus™ ignition system is standard with this
appliance.
INTERMITTENT
PILOT IGNITOR
RC100 RC200
RC300
(OPTIONAL WALL CONTROLS)
TO CORD ASSEMBLY
120VAC
MODULE
AUX2 NOT USED FOR INSERT MODELS.
ORG
AUX300 MODULE
FAN
PROTECTIVE COVER INCLUDED
WHT
FLAME
MODULATION
TO CORD
ASSEMBLY
(110V)
AUX2
AUX1
BATTERY PACK
6V DC
RED
BLK
RED
BLK
ORANGE
(PILOT)
ROCKER
SWITCH
GREEN
(MAIN)
BROWN
WALL SWITCH
OR REMOTE
INSTALL
GROUND
Figure 10.1 IPI Wiring Diagram
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
25
• An IntelliFire Plus™ Wireless Controls or WSK-21
wired wall switch may be used with the IntelliFire
Plus™ Ignition System. Hearth & Home Technologies
recommends that IntelliFire Plus™ wireless controls be
used for their features and functionality with the Intel-
liFire Plus™ ignition system.
C. Optional Accessories Requirements
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
• To connect optional accessories, the supplied cord as-
sembly should be used. See attached Figure 10.2 for
a wiring diagram for a blower or remote.
• A standard ON/OFF switch is compatible.
Wiring for optional Hearth & Home Technologies approved
accessories should be done now to avoid reconstruction.
Follow instructions that come with those accessories.
WARNING! Risk of Shock! Label all wires prior to dis-
connection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
• Plug the cord into a convenient outlet.
• Must use cord supplied.
WARNING! Risk of Shock! Replace damaged wire with
type 105° C rated wire. Wire must have high temperature
insulation.
NOTE: IF ANY OF THE ORIGINAL
PLUG
BLOWER
WIRE AS SUPPLIED WITH THE
APPLIANCE MUST BE REPLACED,
IT MUST BE REPLACED WITH TYPE
1050 C RATED WIRE.
120V EXISTING
OUTLET
NOTE: USE ZIPTIES TO RESTRAIN
THE LOOSE WIRES UNDERNEATH
THE APPLIANCE AND KEEP THEM
AWAY FROM THE BLOWER WHEEL
(FAN BLADES).
JUMPER WIRE
TEMPERATURE
SENSOR SWITCH
TO VALVE
ORG
BLK
WHT (2)
GRN (2)
BLK (2)
GRN
SPEED CONTROL
(RHEOSTAT)
BLK (2)
GRN (2)
BLK (2)
BRN
TO VALVE BRACKET
(GROUND)
BLK
RED
PLUG INTO 120V
EXISTING OUTLET
DC REGULATOR
RECEPTACLE
VARIABLE SPEED
CONTROL
BLK
BLK
BLK
BLK
WHT
GRN
BLK
GRN
BLK
BLK
BLOWERS
BLOWER
RECEPTACLE
TEMPERATURE
SENSOR SWITCH
BLK
BLK
GRN
WHT
GRN
BLK
Figure 10.2 Fan Wiring Diagram
26
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
2. Plug two cord assembly spade connectors together.
3. Unplug fan cord assembly from standard cord assembly.
4. Plug fan cord assembly into AUX300 module.
D. Fan Wiring with Remote
This appliance may be used with an RC200 or RC300
remote control. See Figure 10.3.
1. Remove cord assembly spades from rheostat and
sensor switch.
5. Plug AUX300 module into the standard cord assembly.
NOTICE: Fan speed and operation are controlled by the
remote control. The sensor switch and rheostat are no
longer needed.
E. Control Module Operation
See Section 2.H for control module operation instructions.
NOTE: IF ANY OF THE ORIGINAL
WIRE AS SUPPLIED WITH THE
APPLIANCE MUST BE REPLACED,
IT MUST BE REPLACED WITH TYPE
PLUG
1050 C RATED WIRE.
120V EXISTING
BLOWER
OUTLET
STEP 5
NOTE: USE ZIPTIES TO RESTRAIN
THE LOOSE WIRES UNDERNEATH
THE APPLIANCE AND KEEP THEM
AWAY FROM THE BLOWER WHEEL
(FAN BLADES).
STEPS
1 & 2
STEPS
3 & 4
SENSOR SWITCH
WHT (2)
GRN (2)
BLK (2)
BLK (2)
GRN (2)
BLK (2)
SPEED CONTROL
(RHEOSTAT)
NOTE: SENSOR SWITCH AND
RHEOSTATSPEED CONTROLMUST
BE REMOVED FROM CIRCUIT IF
SYSTEM IS CONTROLLED WITH
RC200/RC300 REMOTE.
PLUG INTO 120V
EXISTING OUTLET
BLK
GRN
WHT
GRN
BLK
DC REGULATOR
RECEPTICLE
BLK
BLOWERS
AUX 300 MODULE
FAN
TO CONTROL
MODULE
BLK
BLK
BLK
BLK
GRN
WHT
GRN
BLK
BLOWER
RECEPTICLE
Figure 10.3 Wiring Diagram - Fan with RC200/RC300 Remote
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
27
Finishing
11
A. Mantel and Wall Projections
EXISTING NON-COMBUSTIBLE FACING
WARNING! Risk of Fire! Comply with all minimum clear-
ances to combustibles as specified. Framing or finishing
material closer than the minimums listed must be construct-
ed entirely of noncombustible materials (i.e., steel studs,
concrete board, etc).
12 IN. MAX.
Clearance to combustible material under the insert is 1/4
inch (6 mm). Clearance from top of fireplace opening for
combustibles extending 12 inches max. is 12 inches.
• Use leveling legs to raise insert minimum 1/4 inch (6 mm)
above combustible material or outer wrap of factory built
firebox.
12 IN. MIN.
Combustible facings must not extend behind the insert
surround. For non-combustible material specifications
refer to section 1.E.
Figure 11.1 Clearances to Mantels or other Combustibles
above Appliance
28
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
Appliance Setup
12
A. Remove Glass Assembly
See Section 12.F.
B. Remove the Shipping Materials
RETAINING
BRACKET
Remove shipping materials from inside or underneath the
SELF-DRILLING
SCREW
GLASS
firebox.
PANEL
C. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
RETAINING TAB
D. Accessories
Install approved accessories per instructions included
with accessories. Contact your dealer for a list of ap-
proved accessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional acces-
sories with this appliance. Using non-listed accessories
could result in a safety hazard and will void the warranty.
Figure 12.2 Bend Retaining Tab Down
E. Glass Panel Instructions
1. Install back glass panel (see Figure 12.1). Bend retain-
ing tab down to hold back glass panel in position (see
Figure 11.2).
2. Install left glass panel (see Figure 12.1). Install retain-
ing bracket with the self-drilling screw provided to hold
the left glass panel in position (see Figure 12.2).
3. Install right glass panel (see Figure 12.1). Install re-
taining bracket with the self-drilling screw provided to
hold the right glass panel in position (see Figure 12.2).
SMOOTH SURFACE MUST FACE OUT
B
A
C
Figure 12.1 Placement of Glass Panels
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
29
F. Fixed Glass Assembly
G. Air Shutter Setting
Air shutter settings should be adjusted by a qualified ser-
vice technician at the time of installation. The air shutter is
set at the factory for minimum vertical vent run. Adjust air
shutter for longer vertical runs. See Figure 12.4.
Removing Fixed Glass Assembly
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
NOTICE: If sooting occurs, provide more air by opening
the air shutter.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
• Replace as a complete assembly.
Removing Fixed Glass Assembly
• The glass assembly fastens to the fireplace in four
places. Four of the fastening mechanisms are spring-
loaded glass latches. An example of the glass latch
is shown in Figure 12.3.
•
To release glass assembly, pull the two bottom
spring-loaded latches forward and allow them to re-
tract away from the glass assembly. Slide the glass
assembly outward and downward until the top latches
disengage.
Figure 12.4 Air Shutter
Replacing Fixed Glass Assembly
• Tilt glass assembly toward fireplace and slide glass
assembly upward to engage top latches. Verify top
latches are fully engaged and then fasten the two
bottom latches.
Air Shutter Settings
NG
LP
COSMO-I30
COSMO-I35
1/8 in.
1/8 in.
1/4 in.
1/4 in.
Figure 12.3 Fixed Glass Assembly
30
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
Troubleshooting
13
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you
do experience a problem, this troubleshooting guide will assist a qualified technician in the diagnosis of a problem and the
corrective action to be taken. This troubleshooting guide can only be used by a qualified technician. Contact your dealer to
arrange a service call by a qualified technician.
A. IntelliFire Plus™ Ignition System
Symptom
Possible Cause
Corrective Action
1. Pilot won’t light.
The ignitor/module
makes noise, but no
spark.
A. Incorrect wiring.
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are
connected to correct terminals on module and pilot assembly.
B. Loose connections or electrical
shorts in the wiring.
Verify no loose connections or electrical shorts in wiring from mod-
ule to pilot assembly. Verify connections underneath pilot assembly
are tight; also verify igniter and flame sense wires are not grounding
out to metal chassis, pilot burner, pilot enclosure, mesh screen if
present, or any other metal object.
C. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
2. Pilot won’t light,
there is no noise or
spark.
A. No power, transformer installed
incorrectly, or depleted batteries.
Verify that transformer is installed and plugged into module. Check
voltage of transformer at connection to module. Acceptable read-
ings of a good transformer are between 6.4 and 6.6 volts AC. Bat-
tery power supply voltage must be at least 4 volts. If below 4 volts,
replace batteries.
B. A shorted or loose connection in
wiring configuration or wiring har-
ness.
Remove and reinstall the wiring harness that plugs into module.
Verify there is a tight fit. Verify pilot assembly wiring to module. Re-
move and verify continuity of each wire in wiring harness. Replace
any damaged components.
C. Improper wall switch wiring.
D. Module not grounded.
Verify that 120/VAC power is “ON” to junction box.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
3. Pilot sparks, but
Pilot will not light.
A. Gas supply.
Verify that incoming gas line ball valve is “open”. Verify that inlet
pressure reading is within acceptable limits.
B. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
C. Module is not grounded.
D. Pilot valve solenoid
Verify module is securely grounded to metal chassis of appliance.
Verify that 1.5 to 1.8 VDC is supplied to pilot solenoid from module.
If below 1.5 volts, replace module. If 1.5 volts or greater, replace
valve.
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
31
IntelliFire Plus™ Ignition System (continued)
Symptom
Possible Cause
Corrective Action
4. Pilot lights but con-
tinues to spark, and
main burner will not
ignite. (If the pilot
continues to spark
after the pilot flame
has been lit, flame
rectification has not
occurred.)
A. A shorted or loose connection in
Verify all connections to wiring diagram in manual. Verify connec-
tions underneath pilot assembly are tight. Verify flame sense or ig-
niter wires are not grounding out to metal chassis, pilot burner, pilot
enclosure or screen if present, or any other metal object.
flame sensing rod.
B. Poor flame rectification or contami- With fixed glass assembly in place, verify that flame is engulfing
nated flame sensing rod.
flame sensing rod on left side of pilot hood. Flame sensing rod
should glow shortly after ignition. With a multi-meter, verify that cur-
rent in series between module and sense lead is at least 0.14 mi-
croamps. Verify correct pilot orifice is installed and gas inlet is set to
pressure specifications. Clean flame sensing rod with emery cloth
to remove any contaminants that may have accumulated on flame
sensing rod.
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance.
Verify that wire harness is firmly connected to the module.
D. Damaged pilot assembly or con-
Verify that ceramic insulator around the flame sensing rod is not
cracked, damaged, or loose. Verify connection from flame sensing
rod to white sensor wire. Clean flame sensing rod with emery cloth
to remove any contaminants that may have accumulated on flame
sensing rod. Verify continuity with a multi-meter with ohms set at
lowest range. Replace pilot if any damage is detected.
taminated flame sensing rod.
32
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
Reference Materials
14
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only.
A
H
S
O
Q
R
P
G
T
B
C
D
F
I
E
M
J
GAS LINE
K
ACCESS
ELECTRICAL
ACCESS
N
L
MODEL DIMENSIONS
MODEL DIMENSIONS
COSMO-I35
COSMO-I35
COSMO-I30
COSMO-I30
Location
Location
Inches Millimeters Inches Millimeters
Inches Millimeters Inches Millimeters
A
B
C
D
E
F
23-1/2
34-5/8
31-9/16
15-11/16
24
597
879
802
398
610
535
403
298
518
44
20-3/16
30-1/2
27-7/16
12-13/16
20-1/2
17-5/8
14-5/8
10-1/8
17
513
775
697
325
521
448
372
257
432
44
K
L
4-13/16
10-1/16
2-1/4
5
122
256
57
4-13/16
9
122
229
57
M
N
O
P
Q
R
S
T
2-1/4
3-15/16
5-3/16
8
127
130
203
46
100
132
203
44
5-1/8
8
21-1/16
15-7/8
11-3/4
20-3/8
1-3/4
G*
H
I
1-13/16
2-1/4
4-13/16
10-1/2
1-3/4
2-1/4
4-7/16
9-1/2
57
57
122
267
113
241
J
1-3/4
*Note: Location G on Figure 14.1 is measuring the appliance depth, for installation depth reference Location G
on Figure 5.1.
Figure 14.1 Appliance Dimensions
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
33
B. Vent Kits Components
Direct Vent Flex Liner Kits (see Figure 14.2)
LINK-DV-30B or (LINK-DV-30): Masonry 3 inch flex liner
kit. Expands to 30 feet. Includes: two liners, termination
cap, flashing, and link adapter.
LINK-DV4-30B or (LINK-DV4-30): Masonry 3 inch flex liner
kit. Expands to 30 feet and 4 feet respectively. Includes:
two liners, termination cap, flashing, and link adapter.
FLASH-DAMP
LINK-ZC-ADP
LINK-DV-30B
(LINK-DV-30)
DV-46DVA-GK
FLEX3-30
LINK-DV4-30B
(LINK-DV4-30)
Figure 14.2 Direct Vent Flex Liner Kits
FLEX3-CNCT
Direct Vent Flex Liner Accessory Kits (see Figure 14.3)
Flash-Damp: Zero clearance damper flashing kit for use
with the LINK-DV-30B or LINK-DV4-30B liner kits.
Figure 14.3 Direct Vent Flex Liner Accessory Kits
LINK-ZC-ADP: Zero clearance chimney adapter
DV-46DVA-GK: Adapter kit (colinear to coaxial 3 inches
included in above kits). It is permissible to use DV-46DVA-
GK to connect collinear flex vent to SL-D vent pipe to
extend the run.
FLEX3-30: One 3 inch flexible liner expands to 30 feet.
FLEX-CNCT: Connector kit - 3 inch liner to 3 inch liner,
one connector per kit.
34
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
COSMO-I30
C. Service Parts
Beginning Manufacturing Date: June 2010
Ending Manufacturing Date: ______
30” Modern Metal Insert, IPI
2
1
3
4
5
11
10
8
7
9
6
Part number list on following page.
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
35
C. Service Parts List
COSMO-I30
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
Stocked
at Depot
ITEM
DESCRIPTION
Termination Plate Assembly
COMMENTS
PART NUMBER
2206-012
438-351
1
Flex Pipe Handle
Gasket
2206-401
2203-007
2203-103
2239-100
2206-800
GLA-2206
100-512
Burner Assembly
Burner Leg
2
3
Y
Base Pan
4
On/Off Rheostat
Glass Door Assembly
Rheostat Knob
Control Panel
Blower
5
Y
Y
Y
6
7
2205-129
GFK-210
2206-068
2201-017
8
9
Wire Assembly
Power cord Assembly
10
11
Y
Y
Gasket Assembly
2206-080
Gems, Black
Qyt 2 req
Qty 2 req
Qty 2 req
MEDIA-BK-GEMS
2155-045
Glass Latch Assembly, Bottom
Glass Latch Assembly, Top
Glass Refractory, Back
Glass Refractory, Left
Glass Refractory, Right
Jumper wire
Y
Y
339-121A
2239-200
2239-201
2239-202
2187-198
Y
Y
Remote Wire Assembly
Touch Up Paint
2103-013
TUP-GBK-12
Conversion Kit NG
Conversion Kit LP
Pilot Orifice NG
Pilot Orifice LP
Regulator NG
NGK-COSMOI30
LPK-COSMOI30
2098-520
Y
Y
Y
Y
Y
Y
2098-512
NGK-DXV-50
LPK-DXV-50
Regulator LP
Additional service part numbers appear on following page.
36
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
C. Service Parts
COSMO-I35
Beginning Manufacturing Date: June 2010
35” Modern Metal Insert, IPI
Ending Manufacturing Date: ______
2
1
3
4
5
11
10
8
7
9
6
Part number list on following page.
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
37
C. Service Parts List
COSMO-I35
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
Stocked
at Depot
ITEM
DESCRIPTION
Termination Plate Assembly
COMMENTS
PART NUMBER
2205-012
438-351
1
Flex Pipe Handle
Gasket
2206-401
2204-007
2238-103
2238-100
2206-800
GLA-2205
100-512
Burner Assembly
Burner Leg
2
3
Y
4
Base Pan
5
On/Off Rheostat
Glass Door Assembly
Rheostat Knob
Control Panel
Blower
Y
Y
Y
6
7
2205-129
GFK-210
2206-068
2201-017
8
9
10
11
Wire Assembly
Power cord Assembly
Y
Y
2206-080
Gasket Assembly
Qty 2 req
Qty 2 req
Qty 2 req
Gems. Black
MEDIA-BK-GEMS
2155-045
Glass Latch Assembly, Bottom
Glass Latch Assembly, Top
Glass Refractory, Back
Glass Refractory, Left
Glass Refractory, Right
Jumper wire
Y
Y
339-121A
2238-200
2238-201
2238-202
2187-198
Y
Y
2103-013
Remote Wire Assembly
Touch Up Paint
TUP-GBK-12
Conversion Kit NG
Conversion Kit LP
Pilot Orifice NG
Pilot Orifice LP
Regulator NG
NGK-COSMOI35
LPK-COSMOI35
2098-520
Y
Y
Y
Y
Y
Y
2098-512
NGK-DXV-50
LPK-DXV-50
Regulator LP
Additional service part numbers appear on following page.
38
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
COSMO-I30, COSMO-I35
Service Parts
Beginning Manufacturing Date: June 2010
Ending Manufacturing Date: ______
#12 IPI Valve Assembly
3
2
1
4
5
6
7
14
13
12
11
10
8
9
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
Stocked
at Depot
ITEM
DESCRIPTION
Flexible Gas Connector
COMMENTS
PART NUMBER
7000-156
582-842
12.1
Y
Y
Y
Y
Y
Y
Y
Orifice NG (#42C)
Orifice LP (#54C)
Orifice NG (#38C)
Orifice LP (#52C)
Pilot Assembly NG
Pilot Assembly LP
Pilot Bracket
COSMO-I30
COSMO-I35
582-854
12.2
582-838
582-852
2198-014
2198-015
2239-112
2205-128
2205-146
302-320A
2166-302
2166-303
303-315/5
2166-323
2166-304
2166-305
2166-307
046-018A
12.3
12.4
12.5
12.6
12.7
Control Panel Bracket
Valve Bracket
Flex Ball Valve Assembly
Valve NG
Y
Y
Y
Y
Y
Y
Y
Y
Y
12.8
12.9
Valve LP
Brass Connector
PKG of 5
12.10 Battery Pack**
12.11 Wire Assembly
12.12 Transformer
12.13 Control Module
12.14 Temp Sensor Switch
**Fuse for battery pack can be sourced locally, not a warranty item. Specs are 500mA~10A 3/4” long
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
39
D. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies Inc.
7571 215th Street West, Lakeville, MN 55044
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
- NOTES -
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487,
5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712,
6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.
2000-945
Printed in U.S.A. - Copyright 2011
40
Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11
|