BLender
item Stock number
169053
UPC: 681131690539
For Customer asistance, call Customer Service at
1-877-207-0923 (US) or 1-877-556-0973 (Canada)
169053 • 681131690539
sAve tHese instruCtions!
Consumer Safety information
This appliance is intended for indoor household use only.
Short Power Supply Cord information
A short power supply cord is provided to reduce the risk of becoming entangled in
or tripping over a long cord. extension cords may be used if care is exercised in
their use.
if an extension cord is used, the marked electrical rating of the extension cord
should be at least as great as the electrical rating of the appliance. the cord
should be arranged so that it will not drape over the countertop or tabletop where
it can be pulled on by children or tripped over unintentionally. if the appliance is of
the grounded type, the extension cord should be a grounding-type 3-wire cord.
Grounding instructions
this appliance must be grounded while in use to protect the operator from
electrical shock. the appliance is equipped with a 3-conductor cord and a 3-prong
grounding-type plug to fit the proper grounding-type receptacle. the appliance
has a plug that looks like sketch A. An adaptor, sketch B, should be used for
connecting sketch A-type plug to two-ground receptacles. the grounding tab,
which extends from the adaptor, must be connected to a permanent ground such
as a properly grounded outlet box as shown in sketch C, using a metal screw.
3
PArts
1. Blender Base
2. Power on Light
3. Power switch (see detail)
4. Blade Collar
5. Filler Cap
6. Blade
7. Glass Jar
8. Lid
9. Cord storage
moDeL
model no. rated voltage rated power Capacity
Dimensions
Weight
44x22x20Cm
3.984Kg
169053 120v 500W 1.25L
17.3x8.7x7.9 inches 8.783 lb.
4
HoW to AssemBLe
Control Panel
Before First Use: After unpacking the blender, wash everything except the blender base
in hot, soapy water. Dry thoroughly. Wipe the blender base with a damp cloth or sponge.
Do not immerse tHe BAse in WAter. Care should be taken when handling the cutting
blades as they are very sharp.
1. Before starting, make sure that the blender cord is unplugged and that the power
switch, located on the middle of the blender base is in the “off” position.
2. Check the jar to be certain that the cutting blade assembly gasket (a), rubber seal (b),
and jar gasket (c) are in the proper positions. Cutting blade assembly must be
securely tightened to the jar before placing food or liquid in the jar. tighten the cutting
blade assembly by holding the jar and rotating the cutting blade assembly clockwise.
3. Place the jar assembly on the blender base so that it is firmly seated and not tilted to
one side. never place the blade assembly on the blender base without the jar being
completely assembled and securely tightened.
oPerAtinG instruCtions
1. Add ingredients to be processed and place lid on the jar. Be sure lid is fully seated. Be
sure the power switch is still in the “off” position before plugging the blender into the
wall outlet.
2. Blue light indicates power on. You can start to operate the unit.
3. turn the power switch to your desired setting.
on— For ingredients that require continuous processing to a smooth mixture, use
“on” setting.
Pulse— short bursts of power. it is used for chopping and ice-crushing. You can hold
the power switch down in the “Pulse” position for continuous processing until
desired texture is achieved.
off— to stop processing, turn the power switch to “off” position.
4. Always be sure to switch the power switch to the “off” position when you are
not blending.
5
user mAintenAnCe instruCtions
Cleaning
1. Before cleaning, be sure that the unit is “off,” power-on light is off and the cord
is unplugged from the outlet.
2. Whenever possible, rinse the filler cap and lid immediately after processing to
make cleanup easier. Do not immerse the motor base in liquid. iF washing the
jar by hand, wash in hot, soapy water, rinse, and dry thoroughly. if necessary,
use a nylon bristle brush to thoroughly clean the jar.
3. Do not use rough scouring pads or cleansers on any plastic or metal parts.
4. Do not fill the jar with boiling water. Do not place any of the parts in boiling
water.
5. Do not allow the blade assembly in the jar to soak in water for long periods
of time.
CaUTion – never immerSe THe BaSe in waTer or anY oTHer LiqUid
6
Customer AssistAnCe
if you have a claim under this warranty, please call our Customer Assistance number.
For faster service, please have the model, type and series numbers ready for the
operator to assist you. these numbers can be found on the bottom of your appliance.
model: _________Type: ____________________ Series: ___________________
Customer Assistance number 1-877-207-0923 (u.s.) or 1-877-556-0973 (Canada)
Keep these numbers for future reference!
How does state law relate to this
Two-Year LimiTed warranTY
warranty?
what does your warranty cover?
• this warranty gives you specific legal
rights, and you may also have other
rights which vary from state to state
or province to province.
• Any defect in material or workmanship.
For how long after the original purchase?
• two years.
• this warranty is in lieu of any other
warranty or condition, whether express
or implied, written or oral, including,
without limitation, any statutory
warranty or condition of merchantability
or fitness for a particular purpose.
what will we do?
• Provide you with a new one.
• For those items still under warranty but
no longer available, WAL-mArt reserves
the right to replace with a similar Ge
branded product of equal or greater value.
• WAL-mArt, Ge and the product
manufacturer expressly disclaim all
responsibility for special, incidental and
consequential damages or losses caused
by use of this appliance. Any liability is
expressly limited to an amount equal to
the purchase price paid whether a claim,
however instituted, is based on contract,
indemnity, warranty, tort (including
negligence), strict liability, or otherwise.
some states or provinces do not allow
this exclusion or limitation of incidental
or consequential losses so the foregoing
disclaimer may not apply to you.
How do you make a warranty claim?
• save your receipt.
• Properly pack your unit. We recommend
using the original carton and packing
materials.
• return the product to your nearest
WAL-mArt store or call Customer
Assistance at 1-877-207-0923 (u.s.)
or 1-877-556-0973 (Canada).
what does your warranty not cover?
• Parts subject to wear, including, without
limitation, glass parts, glass containers,
cutter/strainer, blades, seals, gaskets,
clutches, motor brushes, and/or
agitators, etc.
• Commercial use or any other use not
found in printed directions.
• Damage from misuse, abuse, or neglect,
including failure to clean product
regularly in accordance with
what if you encounter a problem with
this product while using it outside the
country of purchase?
• the warranty is valid only in the country
of purchase and you follow the warranty
claim procedure as noted.
manufacturer’s instructions.
marketed in Canada by:
Wal-mart Canada Corp.
1940 Argentia road, mississauga, ontario L5n1P9
is a trademark of General electric
Company and is used under the
license by Wal-mart stores inc.,
Bentonville, Ar 72716
|