Fusion Electronics Car Speaker MS BX3020 User Manual

USER / INSTALLATION MANUAL  
MS-BX3020  
2 WAY FULL RANGE CABIN SPEAKERS  
FUSION Electronics New Zealand  
FUSION Electronics Australia  
FUSION Electronics Europe  
FUSION Electronics USA  
09 369 2900  
1300 736 012  
+31 76 5723 632  
623 580 9000  
FUSION Electronics Pacific  
+64 9 369 2900  
WWW.FUSIONELECTRONICS.COM  
WWW.FUSIONELECTRONICS.COM  
CONTENTS OF THE BOX:  
2 x Speakers  
2 x Fully tinned speaker wires  
2 x Mounting Brackets  
4 x Mounting knobs and washers  
4 x Stainless Steel Mounting Screws  
Manual  
Warranty Card  
SPECIFICATIONS  
Woofer Size:  
3”  
Cone Material:  
Tweeter Type:  
Box Type:  
Waterproof paper  
Fabric Dome  
Sealed, ABS  
100  
Peak Power (watts):  
Efficiency (1W/1M):  
85 db  
Frequency Response: 200 Hz – 20 kHz  
Impedance:  
4 ohms  
DIMENSIONS  
Length 164mm  
Width 90mm  
Depth 112mm  
6-15/32”  
3-17/32”  
4-13/32”  
6
3
INSTALLATION GUIDE  
INSTALLATION TIPS  
1.  
Check mounting position for adequate space (see caution)  
Any speaker will only perform to its best capabilities, when correctly  
placed in the listening area. FUSION Engineers recognise that unlike a  
home or motor vehicle installation, there are an extremely wide range of  
marine environments where speakers may be placed.  
2.  
Place the mounting bracket in position, then mark and drill  
mounting holes.  
3.  
4.  
Place the mounting bracket and affix with supplied screws.  
FUSION MS-BX3020 full range marine speakers are optimised and  
tuned to work perfectly with the MS-AB1060R Active Subwoofer with a 2  
channel speaker amplifier which not only powers the speakers but also  
adds impressive low end to the audio experience, a little thought and care  
with placement of the speakers will result in better sound.  
Connect the wires from the source unit to the cabin speaker  
ensuring the correct polarity is observed.  
5.  
6.  
Attach the cabin speaker to the bracket using the washers and  
mounting knobs supplied.  
• High frequencies are directional. Placing the speakers low down in the  
boat will lose some of its information.  
Adjust the angle of the speaker to the preferred position before  
tightening the mounting knobs.  
• Speakers should be placed to simulate a “sound stage”, by being  
placed where you are able to hear both speakers in a stereo situation.  
CAUTION: For speaker mounting restrictions related to Magnetic  
interference, please refer to the manufacturers recommendations for any  
navigational equipment.  
TROUBLESHOOTING  
Before you contact your FUSION dealer or service centre, FUSION  
requires that you do some simple troubleshooting to help diagnose or  
resolve the problem.  
PROBLEM  
SOLUTION  
No Sound  
Check all connections from the source unit  
amplifier to the speaker terminals are  
connected correctly.  
System lacks in bass  
Check the connections from the source  
unit/amplifier to the speaker. Check Polarity.  
System lacks in  
high frequencies:  
Check Polarity  
Check the bass / treble control settings on the  
source unit.  
Distorted sound  
Check all wiring  
Check that it is not the surrounding panels of  
the craft rattling. Check connections from the  
source to the speaker.  
4
5

Audiovox MMD7HRG User Manual
Bryan Boilers LDTV 20 User Manual
Casio Cash Register TE 4000F User Manual
Clarion DXZ585USB User Manual
Crown Boiler 24 06 User Manual
Hifionics GLX1400 1D User Manual
Hitachi VM E53A User Manual
Hitachi VM E575LA User Manual
IBM M400 User Manual
JVC GR AX301 User Manual