For Your Safety
WARNING
Service
Be sure to read these notes before use
Safety Notes
• Make sure that you use your camera correctly. Read these
safety notes and your Owner’s Manual carefully before use.
• After reading these safety notes, store them in a safe place.
Servicing: Do not attempt to service this video product
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Do not use the camera in the bathroom or shower. This
can cause a fire or electric shock.
Do not use in
the bathroom
or shower
Damage Requiring Service: Unplug this video product from
the wall outlet and refer servicing to qualified service per-
sonnel under the following conditions:
• When the power-supply cord or plug is damaged
• If liquid has been spilled, or objects have fallen into the
video product.
• If the video product has been exposed to rain or water.
• If the video product has been dropped or the cabinet has
been damaged.
If the video product does not operate normally follow the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper adjust-
ment of other controls may result in damage and will often
require extensive work by a qualified technician to restore
the video product to its normal operation.
Never attempt to change or take apart the camera
(never open the case). Failure to observe this pre-
caution can cause fire or electric shock.
About the Icons
The icons shown below are used in this document to indi-
cate the severity of the injury or damage that can result if the
information indicated by the icon is ignored and the product
is used incorrectly as a result.
Do not disas-
semble
Should the case break open as the result of a fall or other
accident, do not touch the exposed parts. Failure to ob-
serve this precaution could result in electric shock
or in injury from touching the damaged parts. Re-
move the battery immediately, taking care to avoid
injury or electric shock, and take the product to the
point of purchase for consultation.
This icon indicates that death or seri-
WARNING ous injury can result if the information
is ignored.
Do not touch
internal
parts
This icon indicates that personal injury
CAUTION or material damage can result if the in-
formation is ignored.
Do not change, heat or unduly twist or pull the connection
cord and do not place heavy objects on the connection
cord. These actions could damage the cord and
cause a fire or electric shock. If the cord is dam-
aged, contact your FUJIFILM dealer.
Do not place the camera on an unstable surface. This
can cause the camera to fall or tip over and cause
injury.
The icons shown below are used to indicate the nature of the
instructions which are to be observed.
When the video product exhibits a distinct change in perfor-
mance — this indicates a need for service.
Triangular icons tell you that this information re-
quires attention (“Important”).
Replacement Parts: When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same character-
istics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
Circular icons with a diagonal bar tell you that the
action indicated is prohibited (“Prohibited”).
Never attempt to take pictures while in motion. Do
not use the camera while walking or driving. This
can result in you falling down or being involved in
a traffic accident.
Filled circles with an exclamation mark indicate an
action that must be performed (“Required”).
Safety Check: Upon completion of any service or repairs to
this video product, ask the service technician to perform
safety checks to determine that the video product is in
proper operating condition.
WARNING
Do not touch any metal parts of the camera during a
thunderstorm. This can cause an electric shock due
to induced current from the lightning discharge.
If a problem arises, turn the camera off, remove the
battery, and disconnect and unplug the AC power
adapter. Continued use of the camera when it is
emitting smoke, is emitting any unusual odor, or
is in any other abnormal state can cause a fire or
Do not use the battery except as specified. Load the
battery as shown by the indicator.
Unplug
from power
socket
Do not heat, change or take apart the battery. Do not
drop or subject the battery to impacts. Do not store the
battery with metallic products. Any of these actions
can cause the battery to burst or leak and cause
fire or injury as a result.
electric shock. Contact your FUJIFILM dealer.
Do not allow water or foreign objects to enter the
camera. If water or foreign objects get inside the
camera, turn the camera off, remove the battery,
and disconnect and unplug the AC power adapt-
er. Continued use of the camera can cause a fire
or electric shock. Contact your FUJIFILM dealer.
iii
For Your Safety
The Battery and Power Supply
Note: Check the type of battery used in your camera and
read the appropriate sections.
WARNING
CAUTION
Use only batteries or AC power adapters specified for
use with this camera. Do not use voltages other than
the power supply voltage shown. The use of other
power sources can cause a fire.
Do not place heavy objects on the camera. This can
cause the heavy object to tip over or fall and
cause injury.
The following describes the proper use of batteries and how
to prolong their life. Incorrect use can shorten battery life or
cause leakage, overheating, fire, or explosion.
Do not move the camera while the AC power adapter
is still connected. Do not pull on the connection cord
to disconnect the AC power adapter. This can dam-
age the power cord or cables and cause a fire or
electric shock.
If the battery leaks and fluid gets in contact with your
eyes, skin or clothing, flush the affected area with clean
water and seek medical attention or call an emergency
number right away.
Li-ion Batteries
Read this section if your camera uses a rechargeable
Li-ion battery.
Do not use the charger to charge batteries other than those
specified here. The supplied charger is for use only
with batteries of the type supplied with the camera.
Using the charger to charge conventional batteries
or other types of rechargeable batteries can cause
the battery to leak, overheat or burst.
Do not cover or wrap the camera or the AC power
adapter in a cloth or blanket. This can cause heat
to build up and distort the casing or cause a fire.
The battery is not charged at shipment. Charge the battery
before use. Keep the battery in its case when not in use.
■ Notes on the Battery
The battery gradually loses its charge when not in use.
Charge the battery one or two days before use.
When you are cleaning the camera or you do not plan
to use the camera for an extended period, remove
the battery and disconnect and unplug the AC power
adapter. Failure to do so can cause a fire or elec-
tric shock.
Do not use in the presence of flammable objects, ex-
plosive gases, or dust.
Battery life can be extended by turning the camera off when
not in use.
When charging ends, unplug the charger from the
power socket. Leaving the charger plugged into
the power socket can cause a fire.
When carrying the battery, install it in a digital cam-
era or keep it in the hard case. When storing the bat-
tery, keep it in the hard case. When discarding, cover
the battery terminals with insulation tape. Contact
with other metallic objects or batteries could
cause the battery to ignite or burst.
Battery capacity decreases at low temperatures; a depleted
battery may not function at when cold. Keep a fully charged
spare battery in a warm place and exchange as necessary,
or keep the battery in your pocket or other warm place and
insert it in the camera only when shooting. Do not place
the battery in direct contact with hand warmers or other
heating devices.
Using a flash too close to a person’s eyes may tempo-
rarily affect the eyesight. Take particular care when
photographing infants and young children.
Keep memory cards out of the reach of small children.
Because memory cards are small, they can be
swallowed by children. Be sure to store memory
cards out of the reach of small children. If a child
swallows a memory card, seek medical attention
or call an emergency number.
When a memory card is removed, the card could come
out of the slot too quickly. Use your finger to hold it and
gently release the card. Injury could result to those
struck by the ejected card.
■ Charging the Battery
Charge the battery in the supplied battery charger. Charging
times will increase at ambient temperatures below +10 °C
(+50 °F) or above +35 °C (+95 °F). Do not attempt to charge
the battery at temperatures above 40 °C (+104 °F); at tem-
peratures below 0 °C (+32 °F), the battery will not charge.
Request regular internal testing and cleaning for your
camera. Build-up of dust in your camera can cause
a fire or electric shock. Contact your FUJIFILM
dealer to request internal cleaning every two
years. Please note that this service is not free of
charge.
CAUTION
Do not attempt to recharge a fully charged battery. The bat-
tery does not however need to be fully discharged before
charging.
Do not use this camera in locations affected by oil
fumes, steam, humidity or dust. This can cause a fire
or electric shock.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
The battery may be warm to the touch immediately after
charging or use. This is normal.
Do not leave this camera in places subject to extremely
high temperatures. Do not leave the camera in loca-
tions such as a sealed vehicle or in direct sunlight.
This can cause a fire.
■ Battery Life
At normal temperatures, the battery can be recharged about
300 times. A noticeable decrease in the length of time the
battery will hold a charge indicates that it has reached the
Keep out of the reach of small children. This product
could cause injury in the hands of a child.
iv
For Your Safety
end of its service life and should be replaced.
move the batteries. Note that the camera clock will be reset. ing. Refer to the instructions provided with the charger for more
• The batteries may be warm to the touch immediately after information. Use the charger with compatible batteries only.
■ Storage
use. Turn the camera off and allow the batteries to cool
before handling.
Performance may be impaired if the battery is left unused
for extended periods when fully charged. Run the battery
flat before storing it.
Ni-MH batteries gradually lose their charge when not in use.
■ Disposal
• Battery capacity tends to decrease at low temperatures.
Keep spare batteries in a pocket or other warm place and
exchange as necessary. Cold batteries may recover some
of their charge when warmed.
• Fingerprints and other stains on the battery terminals
can impair battery performance. Thoroughly clean the
terminals with a soft, dry cloth before inserting them in
the camera.
Dispose of used batteries in accord with local regulations.
If the camera will not be used for an extended period, re-
move the battery and store it in a dry place with an ambient
temperature of from +15 °C to +25 °C (+59 °F to +77 °F). Do
not store in locations exposed to extremes of temperature.
AC Power Addaapptteerrss ((AAvvaaiillaabbllee SSeparately)
This section applies to all camera models. Use only
FUJIFILM AC power adapters designated for use with this
camera. Other adapters could damage the camera.
• The AC power adapter is for indoor use only.
• Be sure the DC plug is securely connected to the camera.
• Turn the camera off before disconnecting the adapter. Dis-
connect the adapter by the plug, not the cable.
• Do not use with other devices.
■ Cautions: Handling the Battery
• Do not transport or store with metal objects such as neck-
laces or hairpins.
• Do not expose to flame or heat.
If the batteries leak, clean the battery compartment
thoroughly before inserting new batteries.
• Do not disassemble or modify.
If fluid from the battery comes into contact with
skin or clothing, flush the affected area with water.
If fluid enters your eyes, immediately flush the affected
area with water and seek medical attention. Do not rub
your eyes. Failure to observe this precaution could result
in permanent visual impairment.
• Use with designated chargers only.
• Dispose of used batteries promptly.
• Do not drop or subject to strong physical shocks.
• Do not expose to water.
• Keep the terminals clean.
• The battery and camera body may become warm to the
touch after extended use. This is normal.
• Do not disassemble.
• Do not expose to high heat and humidity.
• Do not subject to strong physical shocks.
• The adapter may hum or become hot to the touch during
use. This is normal.
• If the adapter causes radio interference, reorient or relocate
the receiving antenna.
■ Ni-MH Batteries
The capacity of Ni-MH batteries may be temporarily reduced
when new, after long periods of disuse, or if they are repeat-
edly recharged before being fully discharged. This is nor-
mal and does not indicate a malfunction. Capacity can be
increased by repeatedly discharging the batteries using the
discharge option in the camera setup menu and recharging
them using a battery charger.
AA Alkalline/Rechargeable Ni-MH Batteries
Read this section if your camera uses AA alkaline or re-
chargeable AA Ni-MH batteries. Information on compat-
ible battery types may be found elsewhere in the camera
manual.
■ Cautions: Handling the Batteries
• Do not expose to water, flame, or heat, or store in warm or
humid conditions.
• Do not transport or store with metal objects such as neck-
laces or hairpins.
• Do not disassemble or modify the batteries or battery
casing.
• Do not subject to strong physical shocks.
• Do not use batteries that are leaking, deformed, or discol-
ored.
• Keep out of reach of infants and small children.
• Insert in the correct orientation.
• Do not mix old and new batteries, batteries with different
charge levels, or batteries of different types.
• If the camera will not be used for an extended period, re-
Q
CAUTION: Do not use the discharge option with alkaline
batteries.
The camera draws a small amount of current even when off.
Ni-MH batteries that have been left in the camera for an ex-
tended period may be drawn down to the point that they no
longer hold a charge. Battery performance may also drop if
the batteries are run down in a device such as a flashlight. Use
the discharge option in the camera setup menu to discharge
Ni-MH batteries. Batteries that no longer hold
a
charge
even after repeatedly being discharged and recharged have
reached the end of their service life and must be replaced.
Ni-MH batteries can be recharged in a battery charger (sold sep-
arately). Batteries may become warm to the touch after charg-
v
For Your Safety
Although the display is manufactured using extremely high-
precision technology, it may contain pixels that are always lit
or that do not light. This is not a malfunction, and images
recorded with the product are unaffected.
Using the Camera
IMPORTANT NOTICE: Read Before Using the Software
Do not aim the camera at extremely bright light sources,
such as the sun in a cloudless sky. Failure to observe this
precaution could damage the camera image sensor.
Direct or indirect export, in whole or in part, of licensed soft-
ware without the permission of the applicable governing
bodies is prohibited.
Trademarkk Information
Take Test Shots
xD-Picture Card and E are trademarks of FUJIFILM
Corporation. The typefaces included herein are solely de-
veloped by DynaComware Taiwan Inc. Macintosh, Quick-
Time, and Mac OS are trademarks of Apple Inc. in the U.S.A.
and other countries. Windows 7, Windows Vista, and the
Windows logo are trademarks of the Microsoft group of
companies. Adobe and Adobe Reader are either trademarks
or registered trademarks of Adobe Systems Incorporated in
the U.S.A. and/or other countries. The SDHC and SDXC logos
are trademarks of SD-3C, LLC. The HDMI logo is a trademark.
YouTube is a trademark of Google Inc. All other trade names
mentioned in this manual are the trademarks or registered
trademarks of their respective owners.
Before taking photographs on important occasions (such as
at weddings or before taking the camera on a trip), take a
test shot and view the results to ensure that the camera is
functioning normally. FUJIFILM Corporation can not accept
liability for damages or lost profits incurred as a result of
product malfunction.
Notes on Copyright
Unless intended solely for personal use, images recorded us-
ing your digital camera system cannot be used in ways that
infringe copyright laws without the consent of the owner.
Note that some restrictions apply to the photographing of
stage performances, entertainments, and exhibits, even
when intended purely for personal use. Users are also asked
to note that the transfer of memory cards containing images
or data protected under copyright laws is only permissible
within the restrictions imposed by those copyright laws.
Electrical Innterference
This camera may interfere with hospital or aviation equip-
ment. Consult with hospital or airline staff before using the
camera in a hospital or on an aircraft.
Haandling
Color Television Systems
To ensure that images are recorded correctly, do not subject
the camera to impact or physical shocks while images are
being recorded.
NTSC (National Television System Committee) is a color televi-
sion telecasting specification adopted mainly in the U.S.A., Can-
ada, and Japan. PAL (Phase Alternation by Line) is a color televi-
sion system adopted mainly in European countries and China.
Liquid CCrystal
In the event that the display is damaged, care should be
taken to avoid contact with liquid crystal. Take the urgent
action indicated should any of the following situations arise:
Electrical Innterference
Exif Print is a newly revised digital camera file format in
which information stored with photographs is used for opti-
mal color reproduction during printing.
•
•
•
If liquid crystal comes in contact with your skin, clean the
area with a cloth and then wash thoroughly with soap and
running water.
If liquid crystal enters your eyes, flush the affected eye with
clean water for at least 15 minutes and then seek medical
assistance.
If liquid crystal is swallowed, rinse your mouth thoroughly
with water. Drink large quantities of water and induce
vomiting, then seek medical assistance.
vi
For Your Safety
Notes on the Grant: To comply with Part 15 of the FCC Rules,
this product must be used with a Fujifilm-specified ferrite-
core A/V cable, USB cable, and DC supply cord.
NOTICES
To prevent fire or shock hazard, do not expose the unit
to rain or moisture.
For Customers in Canada
CAUTION: This Class B digital apparatus complies with Cana-
dian ICES-003.
Please read the “Safety Notes” and make sure you un-
derstand them before using the camera.
Perchlorate Material—special handling may apply. See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate.
Disposall of Electrical and Electronic Equipment in Private
Houseeholds
For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
In the European Union, Norway, Iceland and Liechten-
stein: This symbol on the product, or in the man-
ual and in the warranty, and/or on its packaging
indicates that this product shall not be treated as
household waste. Instead it should be taken to
an applicable collection point for the recycling
of electrical and electronic equipment.
FCC Statement: This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences to the en-
vironment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
CAUTION: This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a This symbol on the batteries or accumulators in-
residential installation. This equipment generates, uses, and dicates that those batteries shall not be treated
can radiate radio frequency energy and, if not installed and as household waste.
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
If your equipment contains easy removable batteries or
guarantee that interference will not occur in a particular in-
accumulators please dispose these separately according to
stallation. If this equipment does cause harmful interference
your local requirements.
to radio or television reception, which can be determined by
The recycling of materials will help to conserve natural re-
sources. For more detailed information about recycling this
product, please contact your local city office, your household
waste disposal service or the shop where you purchased the
product.
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the fol-
lowing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
In Countries Outside the European Union, Norway, Iceland and
Liechtenstein: If you wish to discard this product, including
the batteries or accumulators, please contact your local au-
thorities and ask for the correct way of disposal.
• You are cautioned that any changes or modifications not
expressly approved in this manual could void the user’s
authority to operate the equipment.
vii
About This Manual
Before using the camera, read this manual and the warnings in“For Your Safety”(Pii). For information
on specific topics, consult the sources below.
Task Index .............................................................................................. Pix Table of Contents ................................................. Pxii
Know what you want to do but don’t know the The “Table of Contents” gives an overview of the
name for it? Find the answer in the“Task Index.” entire manual. The principal camera operations
are listed here.
Troubleshooting ................................................P102 Warning Messaggeess aanndd Displays .........................P106
Having a specific problem with the camera? Find out what’s behind that flashing icon or error
Find the answer here.
message in the display.
Glossary............................................................P109 Reessttrriiccttiioonnss oonn CCaammeerraa SSettings..........................P116
The meanings of some technical terms may be See page 116 for restrictions on the options avail-
found here.
able in each shooting mode.
Memoryy Caarrds
Pictures are stored on optional SD, SDHC, and SDXC memory cards (P16), referred to in this manual as“memory
cards.”
viii
Task Index
Find items by task.
■ Exchanging Lenses
■ Adjusting Exposure
Attaching lenses.....................................................................11
Removing lenses....................................................................11
ISO sensitivity...........................................................................48
Metering......................................................................................49
Program autoexposure......................................................24
Shutter priority autoexposure.......................................25
Aperture priority autoexposure....................................26
Manual exposure...................................................................27
Long time exposures...........................................................28
Exposure lock...........................................................................43
Exposure compensation...................................................29
■ Taking Photographs
The optical viewfinder........................................................20
Power management............................................................23
The self-timer...........................................................................41
■ Choosing Image Quality and Size
Image size ..................................................................................67
Image quality...........................................................................67
RAW images..............................................................................53
Color space................................................................................83
■ Adjusting Colors to the Light Source
White balance..........................................................................32
Film simulation........................................................................51
Dynamic range .......................................................................68
Color/tone/sharpness.................................................68, 69
■ Focusing
Focus mode ..............................................................................45
Focus frame selection.........................................................47
Focus lock...................................................................................43
Manual focus............................................................................45
ix
Task Index
■ Choosing a Drive Mode
■ Custom Settings
Burst photography................................................................34
Bracketing ..................................................................................35
Panoramas .................................................................................37
Movies..........................................................................................39
Assigning a role to the Fn button................................50
Saving and recalling settings.........................................52
■ Using the Flash
Flash photography ...............................................................54
Flash mode................................................................................54
Flash compensation ............................................................72
Optional flash units......................................................54, 97
x
Prodduucctt CCaarree
Camera body: For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body
after each use. Do not use alcohol, thinner, or other volatile chemicals, which could discolor or deform
the leather on the camera body. Any liquid on the camera should be removed immediately with a
soft, dry cloth. Use a blower to remove dust from the monitor, taking care to avoid scratches, and then
gently wipe with a soft, dry cloth. Any remaining stains can be removed by wiping gently with a piece
of FUJIFILM lens-cleaning paper to which a small amount of lens-cleaning fluid has been applied. To
prevent dust entering the camera, replace the body cap when not lens is in place.
Image sensor: Dust can be removed from the image sensor using the VSENSOR CLEANING option in
the setup menu (P82).
Lenses: Use a blower to remove dust, then gently wipe with a soft, dry cloth. Any remaining stains can
be removed by wiping gently with a piece of FUJIFILM lens-cleaning paper to which a small amount of
lens-cleaning fluid has been applied. Replace the front and rear caps when the lens is not use.
xi
Table of Contents
For Your Safety.....................................................................................ii
IMPORTANT SAFETY INSTRUCTIONS.........................................ii
Safety Notes.......................................................................................iii
NOTICES..............................................................................................vii
About This Manual..........................................................................viii
Task Index .............................................................................................ix
Product Care ........................................................................................xi
Firstt SSteepps
Attaching the Strap ...........................................................................9
Attaching a Lens .............................................................................. 11
Charging the Battery ..................................................................... 12
Inserting the Battery and a Memory Card........................... 13
Compatible Memory Cards..................................................... 16
Turning the Camera on and Off ................................................ 17
Basic Setup ......................................................................................... 18
Choosing a Display ......................................................................... 19
Using the Hybrid Viewfinder..................................................... 20
The DISP/BACK Button....................................................................... 21
Optical Viewfinder: Shooting................................................. 21
Electronic Viewfinder: Shooting............................................ 21
LCD Monitor: Shooting............................................................. 21
Electronic Viewfinder/LCD Monitor: Playback................. 22
Power Management....................................................................... 23
Before You Begin
Symbols and Conventions..............................................................1
Supplied Accessories........................................................................1
Parts of the Camera...........................................................................2
The Selector ........................................................................................4
The Command Dial ..........................................................................4
The Q (Quick Menu) Button...........................................................5
Camera Displays................................................................................6
Shooting: Optical Viewfinder ....................................................6
Shooting: Electronic Viewfinder...............................................7
Shooting: LCD Monitor................................................................7
Playback: Electronic Viewfinder/LCD Monitor....................8
Taking Phhotoographs
Program AE (P).................................................................................. 24
Shutter-Priority AE (S) ................................................................... 25
Aperture-Priority AE (A) ............................................................... 26
Manual Exposure (M)..................................................................... 27
Long Time-Exposures (T/B)......................................................... 28
Time (T).............................................................................................. 28
Bulb (B)............................................................................................... 28
Exposure Compensation.............................................................. 29
Focusing and Taking Pictures .................................................... 30
xii
Table of Contents
Moorre on Phhotoography
Viewing Pictures
FMacro Mode (Close-ups)......................................................... 31
White Balance ................................................................................... 32
IContinuous Shooting (Burst Mode).................................. 34
Bracketing........................................................................................... 35
Multiple Exposures......................................................................... 36
Panoramas.......................................................................................... 37
FRecording High-Definition (HD) Movies......................... 39
Before Recording ........................................................................... 40
hUsing the Self-Timer ................................................................. 41
Focus/Exposure Lock ..................................................................... 43
Focus Mode ........................................................................................ 45
Focus Frame Selection .................................................................. 47
Sensitivity ........................................................................................... 48
Metering.............................................................................................. 49
The Fn Button.................................................................................... 50
Film Simulation ................................................................................ 51
Saving Settings................................................................................. 52
Recording Pictures in RAW Format ......................................... 53
NFlash Photography...................................................................... 54
Viewing Pictures Full Frame ....................................................... 56
Viewing Photo Information ....................................................... 57
Playback Zoom ............................................................................... 57
Multi-Frame Playback................................................................... 58
Viewing Movies ................................................................................ 59
Image Search..................................................................................... 60
mPhotoBook Assist...................................................................... 61
Creating a PhotoBook.................................................................. 61
Viewing Photobooks .................................................................... 62
Editing and Deleting Photobooks........................................... 62
Viewing Panoramas........................................................................ 63
Viewing Pictures Taken in a Single Burst.............................. 64
xDeleting Pictures....................................................................... 65
Creating JPEG Copies of RAW Pictures.................................. 66
xiii
Table of Contents
cFRAMING GUIDLINE ............................................................ 71
CAF ILLUMINATOR .................................................................. 72
kAE/AF-LOCK MODE.............................................................. 72
vAE/AF-LOCK BUTTON.......................................................... 72
mAUTOROTATE PB ................................................................... 72
pFLASH MODE ......................................................................... 72
IFLASH........................................................................................ 72
BRED EYE REMOVAL............................................................... 73
nSAVE ORG IMAGE.................................................................. 73
WMOVIE MODE......................................................................... 73
Using the Menus: Playback Mode............................................ 74
Playback Menu Options .............................................................. 74
jRAW CONVERSION............................................................... 74
AERASE........................................................................................ 74
GCROP.......................................................................................... 74
eRESIZE ....................................................................................... 75
DPROTECT .................................................................................. 75
CIMAGE ROTATE....................................................................... 75
BRED EYE REMOVAL............................................................... 76
ISLIDE SHOW ........................................................................... 76
mPHOTOBOOK ASSIST ........................................................... 77
jMARK FOR UPLOAD TO ...................................................... 77
bIMAGE SEARCH...................................................................... 77
KPRINT ORDER (DPOF).......................................................... 77
JDISP ASPECT........................................................................... 78
IPLAYBACK VOLUME............................................................. 78
Menus
Using the Menus: Shooting Mode........................................... 67
Shooting Menu Options.............................................................. 67
NISO.............................................................................................. 67
OIMAGE SIZE.............................................................................. 67
TIMAGE QUALITY .................................................................... 67
UDYNAMIC RANGE.................................................................. 68
PFILM SIMULATION ................................................................ 68
XFILM SIMULATION BKT ....................................................... 68
BSELF-TIMER.............................................................................. 68
DWHITE BALANCE ................................................................... 68
fCOLOR....................................................................................... 68
qSHARPNESS............................................................................. 69
rHIGHLIGHT TONE.................................................................. 69
sSHADOW TONE ..................................................................... 69
hNOISE REDUCTION............................................................... 69
KLONG EXPOSURE NR ........................................................... 69
uSELECT CUSTOM SETTING ................................................ 69
KEDIT/SAVE CUSTOM SETTING.......................................... 69
FAF MODE.................................................................................. 69
GCORRECTED AF FRAME...................................................... 70
lFOCAL LENGTH SETTING................................................... 70
mSHOOT WITHOUT LENS...................................................... 70
FFn BUTTON.............................................................................. 70
nMULTIPLE EXPOSURE.......................................................... 70
vDISP. CUSTOM SETTING ..................................................... 71
xiv
Table of Contents
The Setup Menu............................................................................... 79
Using the Setup Menu................................................................. 79
Setup Menu Options .................................................................... 80
FDATE/TIME............................................................................... 80
NTIME DIFFERENCE................................................................. 80
La................................................................................ 80
RRESET......................................................................................... 80
oSILENT MODE......................................................................... 80
BFRAME NO............................................................................... 81
IFOCUS RING............................................................................ 81
JLCD BRIGHTNESS.................................................................. 81
UPOWER SAVE MODE ............................................................ 81
HQUICK START MODE............................................................ 81
MAUTO POWER OFF................................................................ 82
GOPERATION VOL.................................................................... 82
AIMAGE DISP.............................................................................. 82
VSENSOR CLEANING.............................................................. 82
JCOLOR SPACE......................................................................... 83
cGUIDANCE DISPLAY............................................................. 83
MFOCUS SCALE UNITS ........................................................... 83
OBACKGROUND COLOR........................................................ 83
KFORMAT.................................................................................... 83
Connections
Viewing Pictures on TV ................................................................. 84
Printing Pictures via USB ............................................................. 85
Connecting the Camera.............................................................. 85
Printing Selected Pictures .......................................................... 85
Printing the DPOF Print Order .................................................. 86
Creating a DPOF Print Order...................................................... 87
WITH DATE s/WITHOUT DATE............................................ 88
RESET ALL....................................................................................... 89
Viewing Pictures on a Computer.............................................. 90
Windows: Installing MyFinePix Studio .................................. 90
Macintosh: Installing FinePixViewer....................................... 92
Connecting the Camera.............................................................. 94
xv
Table of Contents
Techniccaall NNoottes
Appeenndix
Optional Accessories...................................................................... 96
Accessories from FUJIFILM......................................................... 96
Recommended Third-Party Accessories............................... 98
Connecting the Camera to Other Devices........................... 99
Caring for the Camera .................................................................100
Storage and Use ...........................................................................100
Traveling..........................................................................................100
Cleaning the Image Sensor.......................................................101
Glossary .............................................................................................109
Memory Card Capacity ...............................................................110
Specifications..................................................................................111
Restrictions on Camera Settings............................................116
Troubleshooting
Problems and Solutions .............................................................102
Warning Messages and Displays............................................106
xvi
Before You Begin
Symbols andd Convventions
The following symbols are used in this manual:
QThis information should be read before use to ensure correct operation.
RAdditional information that may be helpful when using the camera.
POther pages in this manual on which related information may be found.
Menus and other text in the displays are shown in bold. In the illustrations in this manual, displays may
be simplified for explanatory purposes.
Supplied Accessories
The following items are included with the camera:
NP-W126 rechargeable battery
BC-W126 battery charger
Clip attaching tool
Body cap
USB cable
• Owner’s Manual (this
manual)
• Shoulder strap
• Protective covers (× 2)
• Diopter adjustment lens
(comes installed in camera)
CD-ROM
Metal strap clips (× 2)
1
Parts of the Camera
For more information, refer to the page listed to the right of each item.
1 Shutter button..................................................30 11 Focus mode selector .........................................45 22 Command dial ....................................................4
2 Exposure compensation dial .............................29 12 Lens signal contacts..........................................11 23 Connector cover.................................... 84, 85, 94
3 Shutter speed dial........................... 24, 25, 26, 27 13 Lens release button ..........................................11 24 Cable channel cover for DC coupler
4 Dial release .................................................25, 27 14 Viewfinder selector...........................................20 25 Battery-chamber cover latch ......................13, 14
5 AF-assist illuminator.........................................72 15 Microphone ......................................................39 26 Battery-chamber cover.....................................13
Self-timer lamp ................................................41 16 ON/OFF switch.................................................17 27 Tripod mount
6 Hot shoe .....................................................55, 99 17 Fn (Function) button........................................50 28 LCD monitor........................................................6
7 Viewfinder window ..........................................20 18 Battery chamber...............................................13 29 HDMI mini connector........................................84
8 Strap eyelet ........................................................9 19 Memory card slot..............................................14 30 USB connector ............................................85, 94
9 Speaker.............................................................59 20 Battery latch...............................................13, 15 31 Body cap...........................................................11
10 Sync terminal....................................................55 21 Eye sensor.........................................................19
2
Parts of the Camera
36 Q (quick menu) button .......................................5
37 MENU/OK button...............................................4
38 Selector ..............................................................4
39 DISP (display)/BACK button ............................21
o(silent mode) button..................................30
40 AF (autofocus) button ................................46, 47
b(delete) button............................................56
41 AE (autoexposure) button ................................49
n(playback zoom out) button .................57, 58
42 DRIVE button...................................................34
k(playback zoom in) button....................57, 58
32 VIEW MODE button .........................................19 34 a(playback) button ......................................56 43 Diopter adjustment lens ...............................6, 98
33 Indicator lamp (see below)
35 AFL/AEL (focus lock/exposure) button.......43, 45
Thhee IInndicator Lamp
The indicator lamp shows camera status as follows:
Indicator lamp
Indicator lamp
Glowwss ggrreen
Blinks green
Caammera sstatus
Focus locked.
Blur, focus, or exposure warning. Picture can be taken.
Blinks green and orange Recording pictures. Additional pictures can be taken.
Glowwss oorraannggee
Blinks red
Recording pictures. No additional pictures can be taken at this time.
Lens or memory error.
R Warnings may also appear in the display (P106).
3
Parts of the Camera
The Selector
Press the selector up ( ), right
The Command Dial
The command dial can be used to navi-
gate the menus, to view the most re-
cent picture (P56), and to select op-
tions in the quick menu display (P5).
q
(
), down ( ), or left ( ) to
w
e
r
highlight items and press MENU/
OK ( ) to select. Pressing the
t
selector up (MACRO) during
shooting displays macro op-
tions (P31).
Press the center of the command dial
to zoom in on the focus area selected
formanualfocus(P46)ortheactivefo-
cus point during playback (P57).
Coontrol Loock
To avoid accidentally displaying macro options dur-
ing shooting, press MENU/OK until X is displayed. The
control can be unlocked by pressing MENU/OK until X
is no longer displayed.
4
Parts of the Camera
The Q (Quick Menu) Button
Press Q for quick access to the following items:
Option
uSELECT CUSTOM SETTING
NISO
P
Option
52 TIMAGE QUALITY
48 PFILM SIMULATION
P
67
51
69
69
68
69
Option
P
41
69
54
81
BSELF-TIMER
FAF MODE
UDYNAMIC RANGE
DWHITE BALANCE
hNOISE REDUCTION
OIMAGE SIZE
68
32
69
67
rHIGHLIGHT TONE
sSHADOW TONE
fCOLOR
IFLASH MODE
JLCD BRIGHTNESS
qSHARPNESS
Press Q to display the quick menu during shooting.
1
Use the selector to highlight items and rotate the command dial to change.
2
3
Press Q to exit when settings are complete.
R For quick access to custom settings banks, press and hold the Q button.
5
Parts of the Camera
Camera Displays
The following types of indicator may be displayed during shooting and playback. Indicators vary with
camera settings.
■ Shooting: Optical Viewfinder
1 Manual focus indicator .....................................45 11 Virtual horizon..................................................71
2 Flash mode .......................................................54 12 Temperature warning .....................................108
3 Metering...........................................................49 13 Bright frame
100
4 White balance...................................................32 14 Distance indicator.......................................45, 83
5 Film simulation.................................................51 15 Sensitivity.........................................................48
6 Dynamic range .................................................68 16 Aperture ............................................... 24, 26, 27
7 Number of available frames......................81, 110 17 Shutter speed ....................................... 24, 25, 27
8 Image quality and size......................................67 18 Shooting mode..........................24, 25, 26, 27, 28
9 Battery level .....................................................17 19 Histogram.........................................................22
10 Focus frame ................................................43, 47 20 Exposure compensation/
exposure indicator ......................................27, 29
Viewfinder Focus
Displayed if the edges of the
picture are outside the bor-
ders of the EVF.
Viewfinder focus can be adjusted using diopter ad-
justment lenses available separately from third-party
suppliers (P98).
6
Parts of the Camera
■ Shooting: Electronic Viewfinder
1 Flash mode .......................................................54 15 Distance indicator.......................................45, 83
2 Macro (close-up) mode.....................................31 16 Battery level .....................................................17
3 Self-timer indicator ..........................................41 17 Sensitivity.........................................................48
4 Continuous mode .............................................34 18 Aperture ............................................... 24, 26, 27
5 White balance...................................................32 19 Shutter speed ....................................... 24, 25, 27
6 Film simulation.................................................51 20 Metering...........................................................49
7 Dynamic range .................................................68 21 Shooting mode..........................24, 25, 26, 27, 28
8 Focus frame ................................................43, 47 22 Manual focus indicator .....................................45
9 Number of available frames......................81, 110 23 Exposure compensation/
10 Image quality and size......................................67
exposure indicator ......................................27, 29
11 Temperature warning .....................................108 24 Histogram.........................................................22
12 Blur warning...................................................106 25 Virtual horizon..................................................71
13 Focus warning ..........................................30, 106 26 Depth-of-field preview.....................................26
14 Silent mode indicator .................................30, 80
■ Shooting: LCD Monitor
1 Flash mode .......................................................54 11 White balance...................................................32
2 Macro (close-up) mode.....................................31 12 Battery level .....................................................17
3 Metering...........................................................49 13 Sensitivity.........................................................48
4 Continuous mode .............................................34 14 Aperture ............................................... 24, 26, 27
5 Silent mode indicator .................................30, 80 15 Focus frame/focus point .............................43, 47
6 Number of available frames......................81, 110 16 Shutter speed ....................................... 24, 25, 27
7 Temperature warning .....................................108 17 Shooting mode..........................24, 25, 26, 27, 28
8 Image quality and size......................................67 18 Focus mode ......................................................45
9 Dynamic range .................................................68 19 Self-timer indicator ..........................................41
10 Film simulation.................................................51 20 Exposure compensation/
exposure indicator ......................................27, 29
7
Parts of the Camera
■ Playback: Electronic Viewfinder/LCD Monitor
1 Rating...............................................................56 6 Playback mode indicator...................................56
2 Red-eye removal indicator................................73 7 Mark for upload to............................................77
3 Silent mode indicator .................................30, 80 8 Photobook assist indicator................................61
4 Gift image.........................................................56 9 DPOF print indicator .........................................87
5 Frame number..................................................81 10 Protected image ...............................................75
/.
3
8
First Steps
Attachinngg tthhee SStrap
Attach the strap clips to the camera and then attach the strap.
Open a strap clip.
Use the clip attaching tool to open a strap clip
as shown.
Pass the clip through the eyelet.
Rotate the clip fully through
the eyelet until it clicks
closed.
1
3
Attach a protective cover.
4
Place a protective cover over the eyelet as
shown, with the black side of the cover toward
the camera. Repeat Steps 1–4 for the second
eyelet.
Q Keep the tool in a safe place. You will need it to
open the strap clips when removing the strap.
Place the strap clip on an eyelet.
Hook the strap eyelet in the clip opening. Re-
move the tool, using the other hand to keep
the clip in place.
2
9
Attaching the Strap
Insert the strap.
Insert the strap through a protective cover
Fasten the strap.
Fasten the strap as shown. Repeat Steps 5–6
5
6
and strap clip.
for the second eyelet.
Q To avoid dropping the camera, be sure the strap is
correctly secured.
10
Attaching a Lens
Lenses attach as described below.
Q Care is required to prevent dust entering the camera while attaching and removing lenses.
Remove the body and rear caps.
Remove the body cap from the camera and
the rear cap from the lens.
1
Removinng Lenses
Lens release button
To remove the lens, turn the
camera off, then press the
lens release button and rotate
the lens as shown.
Q To prevent dust accumulating inside the camera, replace
the body cap when no lens is attached.
Supporteed Lenses (P96)
Q Do not touch the camera’s internal parts.
The camera can be used with optional XF18mmF2 R,
XF35mmF1.4 R, and XF60mmF2.4 R Macro inter-
changeable lenses.
Attach the lens.
2
Place the lens on mount, keeping the marks
on the lens and camera aligned, and then ro-
tate the lens until it clicks into place.
Q Do not press the lens release button while at-
taching the lens.
11
Chhaarrggiinngg the Batteerryy
The battery is not charged at shipment. Charge the battery before use.
Place the battery in the charger.
Place the battery in the supplied battery char-
ger as shown.
Plug the charger in.
Plug the charger into a power outlet. The
charging indicator will light.
1
2
Charge lamp
Thhee CCharggiinngg IInnddicator
The charging indicator shows battery charge sta-
tus as follows:
Charging
Battery charger
Battery status
Action
indicator
Battery not
inserted.
Battery fully
charged.
Insert the battery.
Arrow
Off
Reemmoove the battery.
—
On
Battery charging.
Battery
Unplug the charger
and reemove the
battery.
Blinks
Battery fault.
The camera uses an NP-W126 rechargeable bat-
tery.
Charge the battery.
3
Remove the battery when charging is com-
plete. Seethespecifications(P114)forcharg-
ing times (note that charging times increase
at low temperatures).
Q Unplug the charger when it is not in use.
12
Innsseertinng the Baatttterryy aanndd aa MMemory Cardd
The camera has no internal memory; instead, pictures are stored on optional SD, SDHC, and SDXC
memory cards (sold separately). After charging the battery, insert the battery and memory card as
described below.
Open the battery-chamber cover.
Slide the battery-chamber latch as shown and
open the battery-chamber cover.
Insert the battery.
1
2
Insert the battery as shown inside the battery
chamber, using the battery to keep the bat-
tery latch pressed to one side.
Arrow
Q Do not open the battery-chamber cover when
the camera is on. Failure to observe this precau-
tion could damage image files or memory cards.
Q Do not use excessive force when handling the
battery-chamber cover.
Battery latch
Q Insert the battery in the correct orientation. Do
not use force or attempt to insert the battery up-
side down or backwards. The battery will slide in
easily in the correct orientation.
13
Inserting the Battery and a Memory Card
Q Be sure card is in the correct orientation; do not
insert at an angle or use force.
Q SD/SDHC/SDXC memo-
Insert the memory card.
Holding the memory
card in the orientation
shown at right, slide
it in until it clicks into
place at the back of
the slot.
3
ry cards can be locked,
making it impossible to
format the card or to
record or delete images.
Write-protect switch
Click
Before inserting a memory card, slide the write-
protect switch to the unlocked position.
Close the battery-chamber cover.
Slide the battery-chamber latch as shown and
close the battery-chamber cover.
4
14
Inserting the Battery and a Memory Card
Q Batteries
Reemoving the Battery annd Memorry Caarrdd
• Remove dirt from the battery terminals with a clean,
dry cloth. Failure to observe this precaution could
prevent the battery from charging.
• Do not affix stickers or other objects to the battery.
Failure to observe this precaution could make it im-
possible to remove the battery from the camera.
• Do not short the battery terminals. The battery could
overheat.
• Read the cautions in “The Battery and Power Supply”
(Piv).
• Use only battery chargers designated for use with the
battery. Failure to observe this precaution could re-
sult in product malfunction.
Before removing the battery or memory card, turn
the camera off and open the battery-chamber cover.
To remove the battery, press
the battery latch to the side,
and slide the battery out of
the camera as shown.
Battery latch
To remove the memory card,
press it in and release it slowly.
The card can then be removed
by hand. When a memory card
is removed, the card could come out of the slot too
quickly. Use your finger to hold it and gently release
the card.
• Do not remove the labels from the battery or attempt
to split or peel the outer casing.
• The battery gradually loses its charge when not in
use. Charge the battery one or two days before use.
15
Inserting the Battery and a Memory Card
■ Compatible Memory Cards
FUJIFILM and SanDisk SD, SDHC, and SDXC memory cards have been approved for use in the cam-
era. A complete list of approved memory cards is available at http://www.fujifilm.com/support/digital_
cameras/compatibility/. Operation is not guaranteed with other cards. The camera can not be used
with xD-Picture Cards or MultiMediaCard (MMC) devices.
Q Memory Caarrds
• Do not turn the camera off or remove the memory card while the memory card is being formatted or data are
being recorded to or deleted from the card. Failure to observe this precaution could damage the card.
• Format memory cards before first use, and be sure to reformat all memory cards after using them in a computer
or other device. For more information on formatting memory cards, see page 83.
• Memory cards are small and can be swallowed; keep out of reach of children. If a child swallows a memory card,
seek medical assistance immediately.
• miniSD or microSD adapters that are larger or smaller than the standard dimensions of an SD/SDHC/SDXC card
may not eject normally; if the card does not eject, take the camera to an authorized service representative. Do
not forcibly remove the card.
• Do not affix labels to memory cards. Peeling labels can cause camera malfunction.
• Movie recording may be interrupted with some types of SD/SDHC/SDXC memory card. Use a Gcard or
better when shooting HD movies.
• Formatting a memory card in the camera creates a folder in which pictures are stored. Do not rename or delete
this folder or use a computer or other device to edit, delete, or rename image files. Always use the camera to
delete pictures; before editing or renaming files, copy them to a computer and edit or rename the copies, not
the originals. Renaming the files on the camera can cause problems during playback.
16
Turning the Camera on and Off
Rotate the ON/OFF switch to ON to turn the camera on. Select OFF to turn
the camera off.
R Press the a button to start playback. Press the shutter button halfway to
return to shooting mode.
R The camera will turn off automatically if no operations are performed for the
length of time selected for MAUTO POWER OFF (P82). To reactivate the camera after it has turned off auto-
matically, press the shutter button halfway or turn the ON/OFF switch to OFF and then back to ON.
R For information on other power saving and startup options, see page 23.
Q Fingerprints and other marks on the lens or viewfinder can affect pictures or the view through the viewfinder.
Keep the lens and viewfinder clean.
Batterryy LLevel
After turning the camera on, check the battery level in the display.
Indicator
D(white)
C(white)
B(red)
Description
Battery partially discharged.
Battery more than half discharged
Low battery. Charge as soon as possible.
A(blinks red)
Battery exhausted. Turn camera off and recharge battery.
17
Baassic SSetup
A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as
described below (you can reset the clock or change languages at any time using the FDATE/TIME
orLaoptionsinthesetupmenu;forinformationondisplayingthesetupmenu, seepage80).
Choose a language.
1
Highlight a language and press MENU/OK.
R Press DISP/BACK to skip the current step. Any steps you skip will be displayed
the next time the camera is turned on.
Set the date and time.
2
Press the selector left or right to highlight the year, month, day, hour,
or minute and press up or down to change. To change the order in
which the year, month, and day are displayed, highlight the date for-
mat and press the selector up or down. Press MENU/OK to exit to shoot-
ing mode when settings are complete.
R If the battery is removed for an extended period, the camera clock will be reset and the language-selection
dialog will be displayed when the camera is turned on.
18
Chhooosing a Display
The camera is equipped with a hybrid optical/electronic viewfinder
(OVF/EVF) and an LCD monitor (LCD). Press VIEW MODE to choose a dis-
play.
OVF/EVF
OVF/EVF
LCD
LCD
Automatic display selection
using eye sensor
Viewfinder only
LCD monitor only
Automatic Display Selection
Eye sensor
In this mode, the viewfinder turns on automatically when you put your eye to the view-
finder, and the LCD monitor turns on when you take your eye away (note that the eye sensor
may respond to objects other than your eye or to light shining directly on the sensor).
19
Choosing a Display
Using the Hybrid Viewfinder
Choosing a Display
Use the viewfinder selector to
choose between optical and
electronic viewfinders. Keep
the selector pressed up to
choose the optical viewfinder
display zoom ratio.
Choose a display according to the task.
Display
Description
This display is immune from digital video ef-
fects and allows the subject to be viewed di-
rectly with no display lag. Subjects are always
in focus, allowing you to check their expression
at any time, while a field of view slightly larger
than that of the lens makes it easier to locate
your subject without removing your eye from
the viewfinder. The viewfinder window is how-
ever at a slight distance from the lens, with the
result that the display in the viewfinder may
differ slightly from the final photograph due to
parallax.
Optical
viewfinder
(OVF)
Optical viewfinder display
Electronic viewfinder display
This display shows the view through the lens
and has exactly the same field of view, allowing
Electronic you to frame your subjects precisely and pre-
viewfindeer view focus, depth of field, exposure, and white
(EVF)
balance (although there may be a slight display
lag). It can also be used to view photographs
after shooting.
This display is identical to the electronic view-
finder, except that its large size makes it easier
to view shooting indicators and the view
through the lens. It may however be difficult
to see in bright light.
LCD
monitor
20
The DISP/BACK Button
The DISP/BACK button controls the display of indicators in the viewfinder and LCD monitor.
■ Optical Viewfinder: Shooting
■ LCD Monitor: Shooting
100
Detailed display
Standard display
Standard display
Custom display
■ Electronic Viewfinder: Shooting
.
Custom display
Standard display
Custom display
Custom DDisplay
Choose items for display using vDISP. CUSTOM SETTING in the shooting menu (P71):
Framing grid
Virtual horizon
Exposure (shutter speed, aperture, and sensitivity)
Exposure compensation/exposure indicator
Film simulation
Dynamic range
Focus distance (autofocus)
Focus distance (manual focus)
Histogram
Metering
Flash mode
White balance
Number of exposures remaining/media
Image quality and size
Battery level
R See pages 6–7 for the locations of these items in the displays.
21
The DISP/BACK Buttion
■ Electronic Viewfinder/LCD Monitor: Playback
Indicators displayed
Indicators hidden
Favorites
Photo information
AM
3
Q The optical viewfinder can not be used for playback.
Histoograms
Histograms show the distribution of tones in the im- Optimal exposure: Pixels are distrib-
age. Brightness is shown by the horizontal axis, the uted in an even curve through-
number of pixels by the vertical axis.
out the tone range.
Shadows
Highlights
Overexposed: Pixels are clustered
on the right side of the graph.
No. of pixels
Underexposed: Pixels are clustered
on the left side of the graph.
Pixel brightness
22
Power Mannagement
The setup menu contains the following power management options (P81). For information on using
the setup menu, see page 79.
• UPOWER SAVE MODE: Select ON to increase the number of photographs that can be taken with a
fully-charged battery.
• HQUICK START MODE: Select ON to reduce camera startup time.
UPOWER SAVE MODE
OFF
0.5s
2 minutes
ON
1.0s
—
Startup time
Standby time
OFF
ON
350 shots (1,000 shots when optical vieewwfinder
is used)
Endurance
300 shots
Startup time
Standby time
0.5s
24 minutes
0.5s
10 minutes
250 shots (400 shots when optical viewfinnder is
used)
Endurance
150 shots
R All figures are approximate. The values for endurance are measured under FUJIFILM test conditions and may
vary depending on how the camera is used.
23
Taking Photographs
Proggrraamm AAEE ((PP)
To allow the camera to adjust both shutter speed and aperture
for optimal exposure, rotate the shutter speed dial and lens aper-
ture ring to A. P will appear in the display.
A
16 11
8
5.6
Q If the subject is outside the metering range of the camera, the shutter
speed and aperture displays will show“–––”.
Optical viewfinder
EVF/LCD
Prooggrraamm SShhiifft
If desired, you can press the selector left or right to other combinations of shutter
speed and aperture without altering exposure (program shift). Program shift is not
available if the attached flash supports TTL auto, AUTO is selected for UDYNAM-
IC RANGE in the shooting menu (P68), or an auto option is selected for NISO in
the shooting menu (P48).
Shutter speed
Aperture
24
Shhuutttteerr--PPrriioorriitty AE (S)
To adjust shutter speed manually while letting the camera select
aperture for optimal exposure, rotate the lens aperture ring to A
and use the shutter speed dial (if A is currently selected for shut-
ter speed, press the dial release while rotating the shutter speed
dial). S will appear in the display.
A
16 11
8
5.6
Q If the correct exposure can not be achieved at the selected shutter
speed, aperture will be displayed in red when the shutter button is
pressed halfway. Adjust shutter speed until the correct exposure is
achieved.
Q If the subject is outside the metering range of the camera, the aper-
ture display will show“–––”.
Optical viewfinder
EVF/LCD
25
Aperture--PPrriioorriitty AE (A)
To adjust aperture manually while letting the camera select shut-
ter speed for optimal exposure, rotate the shutter speed dial to A
and use the lens aperture ring. A will appear in the display.
A
16 11
8
5.6
4
2.8
Q If the correct exposure can not be achieved at the selected aper-
ture, the shutter speed will be displayed in red when the shutter but-
ton is pressed halfway. Adjust aperture until the correct exposure is
achieved.
Q If the subject is outside the metering range of the camera, the shutter
speed display will show“–––”.
Q The slowest shutter speed available when ON is selected for
Optical viewfinder
EVF/LCD
/
UPOWER SAVE MODE is 1 4s (P81).
Depth of Field
The aperture ring can be used to adjust aperture before recording begins. Choose
a low f-numbers to soften background details. The effect can be heightened by
increasing the distance between your subject and the background.
A
16 11
8
5.6
4
2.8
Preevviieewwing Depth of Field
When LPREVIEW DEPTH OF FIELD is selected for FFn BUTTON (P50) in the
shooting menu, pressing the Fn button stops aperture down to the selected setting,
allowing depth of field to be previewed in the electronic viewfinder or LCD monitor.
26
Maannual Exppoossuurre (M)
Exposure can be altered from the value suggested by the cam-
era by rotating both the shutter speed dial and aperture ring to
settings other than A (if A is currently selected for shutter speed,
press the dial release while rotating the shutter speed dial). M
will appear in the display.
A
16 11
8
5.6
4
2.8
.
Optical viewfinder
EVF/LCD
R The manual exposure display includes an exposure indicator that
shows the amount the picture would be under- or over-exposed at
current settings.
.
27
Long Time-Exposuures (T/B)
Select a shutter speed of T (time) or B (bulb) for long time-exposures.
R Use of a tripod is recommended to prevent the camera from moving during the exposure.
R To reduce “noise” (mottling) in long time-exposures, select ON for KLONG EXPOSURE NR in the shooting
menu. Note that this may increase the time needed to record images after shooting.
Time (T)
Bulb (B)
Rotate the shutter speed dial to T.
Rotate the shutter speed dial to B.
1
1
Press the selector left or right to
choose a shutter speed between 2s
Press the shutter button all the way
down. The shutter will remain open
for up to 60 minutes while the shut-
ter button is pressed.
2
2
/
and 30s in steps of 1 3EV.
R Selecting an aperture of A fixes shutter speed at 30s.
Using a Remote Release
A remote release (available from third-party suppli-
ers) can be used for long time-exposures.
Press the shutter button all the way
down to take a picture at the select-
ed shutter speed.
3
28
Exposuure Compeensaation
Rotate the exposure compensation dial to adjust exposure when photographing very bright,
very dark, or high-contrast subjects. The effect is visible in the LCD monitor and electronic
viewfinder; when using the optical viewfinder, use the exposure indicator to check exposure.
Exposure compensation indicator
Choosing aan Expossuurre Coommppeennssaattiioonn VVaalue
• Backlit subjects: Choose values
/
/
from +2 3EV to +12 3EV (for an
explanation of the term “EV”,
see the Glossary on page 109).
OVF
EVF
LCD
• Highly reflective subjects or very
bright scenes (e.g., snowfields): +1EV
Choose positive values (+) to
increase exposure
• Scenes that are mostly sky: +1EV
• Spotlit subjects (particularly if photographed against dark back-
/
grounds): –2 3EV
• Subjects with low reflectivity (pine trees or dark-colored foliage):
/
–2 3EV
Choose negative values (–) to
reduce exposure
29
Focusing and Taking Pictures
Press the shutter button halfway to focus and the rest of the way down to shoot.
Focus.
1
Frame the picture with your subject in the center focus area and press the shutter button
halfway to focus.
R If the subject is poorly lit, the AF-assist illuminator may light (P72).
If the camera is able to focus, it will beep twice and focus area will glow green. Focus and exposure will
lock while the shutter button is pressed halfway.
If the camera is unable to focus, the focus frame will turn red, and swill be displayed.
Shoot.
2
Smoothly press the shutter button the rest of the way down to take the picture.
Silennt Mode
In situations in which camera sounds or lights may be unwelcome, press the
DISP/BACK button for a second, or select ON for oSILENT MODE in the setup
menu(P80;notethatsilentmodeisnotavailableduringmovieplayback). The
camera speaker, flash, and AF-assist illuminator/self-timer lamp turn off and
flash and volume settings can not be adjusted.
30
More on Photography
FMaacroo Mooddee ((CClloossee--uuppss))
To focus at short distances, press the selector up (MACRO) and select F. If the optical
viewfinder is on, the camera will automatically switch to the electronic viewfinder
(because of parallax, the optical viewfinder is not recommended). To exit macro
mode, press the selector up left and select OFF.
R The LCD monitor and electronic viewfinder can be used to focus at short ranges when macro mode is not
selected, but the time needed to focus increases.
R The shadow cast by the lens may appear in photographs taken with the flash at distances under 50cm/19.6in.
Turn the flash off or increase the distance to the subject.
31
Whitee BBalance
For natural colors, select DWHITE BALANCE in the shooting menu to display the
following options, then use the selector to highlight an option that matches the
light source and press MENU/OK. The dialog shown at bottom right will be displayed;
use the selector to fine-tune white balance or press DISP/BACK to exit without fine-
tuning (for an explanation of“white balance,”see the Glossary on page 109).
E
HI
Option
Description
Option
j
Description
For subjects in the shade.
AUTO White balance adjusted automatically.
h
k
i
Measure a value for white balance (P33).
k
Use under“daylight”fluorescent lights.
Use under“warm white”fluorescent lights.
Use under“cool white”fluorescent lights.
Use under incandescent lighting.
Reduces the blue cast typically associated
with underwater lighting.
Selecting this option displays a list of color
temperatures (P33); highlight a tempera-
ture and press MENU/OK to select the high-
lighted option and display the fine-tuning
dialog.
l
ET
m
n
g
For subjects in direct sunlight.
R White balance is adjusted for flash lighting only in AUTO and gmodes. Turn the flash off using other white
balance options.
R Results vary with shooting conditions. Play pictures back after shooting to check colors.
R White balance can also be adjusted using the Q button.
32
White Balance
h: Custom White Balance
Choose hto adjust white balance for unusual lighting conditions. White balance measurement options will
be displayed; frame a white object so that it fills the display and press the shutter button all the way down to
measure white balance (to select the most recent custom value and exit without measuring white balance,
press DISP/BACK, or press MENU/OK to select the most recent value and display the fine-tuning dialog).
• If “COMPLETED!” is displayed, press MENU/OK to set white balance to the measured value.
• If “UNDER” is displayed, raise exposure compensation (P29) and try again.
• If “OVER” is displayed, lower exposure compensation and try again.
k: Coolloor Temperature
Color temperature is an objective measure of the color of a light source, expressed in Kelvin (K). Light sources
with a color temperature close to that of direct sunlight appear white; light sources with a lower color tempera-
ture have a yellow or red cast, while those with a higher color temperature are tinged with blue. You can match
color temperature to the light source as shown in the following table, or choose options that differ sharply from
the color of the light source to make pictures“warmer”or“colder.”
Choose for redder light sources
or“colder”pictures
Choose for bluer light sources
or“warmer”pictures
2,000 K
Candlelight
Sunset/sunrise
5,000 K
Direct sunlight
15,000 K
Blue sky
Shade
33
IContinuous Shhoooottiinngg ((BBuurrsstt MMoode)
Capture motion in a series of pictures.
Press the DRIVE button to display
drive options.
Press the shutter button the rest
of the way down to start shoot-
ing. Shooting ends when the shut-
ter button is released, the selected
number of pictures has been taken,
or memory is full.
1
4
R Focus and exposure are determined by the first
frame in each series. The flash turns off automati-
cally; the previously-selected flash mode is restored
when burst shooting is turned off .
R Frame rate varies with shutter speed and may slow
as more shots are taken.
R Additional time may be required to record pictures
when shooting ends.
R If file numbering reaches 999 before shooting is
complete, the remaining pictures will be recorded
to a new folder (P81).
Press the selector up or down to
choose from frame rates of approxi-
mately 6 fps (frames per second)
and 3 fps, and press left or right
to choose the number of shots per
burst.
2
3
Press the shutter button halfway to
focus.
34
Bracketing
Automatically vary settings over a series of pictures.
Press the DRIVE button to display drive options and press the selector up or down
to highlight one of the following:
1
Option
Description
Press the selector left or right to highlight a bracketing amount. Each time the shutter
button is pressed, the camera will take three shots at up to about 6fps: one using the
AE BKT metered value for exposure, the second overexposed by the selected amount, and the
third underexposed by the same amount (regardless of the amount selected, exposure
will not exceed the limits of the exposure metering system).
Press the selector left or right to highlight a bracketing amount. Each time the shutter
is released, the camera will take a picture at the current sensitivity (P48) and process it
ISO BKT to create two additional copies, one with sensitivity raised and the other with sensitivity
lowered by the selected amount (regardless of the amount selected, sensitivity will not
exceed ISO 6400 or fall below ISO 200).
FILM
Each time the shutter is released, the camera takes one shot and processes it to create
SIMULATION copies with the film simulation settings selected for XFILM SIMULATION BKT in the
BKT
shooting menu (P68).
Each time the shutter button is pressed, the camera takes three shots with different
dynamic ranges (P68): 100% for the first, 200% for the second, and 400% for the third.
The shots are taken at rates of up to about 6fps. While dynamic range bracketing is in
effect, sensitivity will be restricted to a minimum of ISO 800; the sensitivity previously in
effect is restored when bracketing ends.
DYNAMIC
RANGE BKT
Press MENU/OK to select the highlighted option.
Take photographs.
2
35
Multiple Exposures
Create a photograph that combines two exposures.
Select ON for nMULTIPLE EXPOSURE in
the shooting menu.
Take the second shot.
1
2
4
5
Take the first shot.
Press MENU/OK to create the multiple
exposure, or press the selector left
to return to Step 4 and retake the
second shot.
Press MENU/OK. You will be prompt-
ed to take the second shot.
3
R To return to Step 2 and retake the first shot, press
the selector left. To save the first shot and exit
without creating a multiple exposure, press DISP/
BACK.
36
Panoramas
Follow an on-screen guide to create a panorama.
Press the DRIVE button to display
drive options. Press the selector up
or down to highlight r (MOTION
PANORAMA) and press MENU/OK.
Pan the camera in the direction shown by the
arrow. Shooting ends automatically when the
camera is panned to the end of the guides
and the panorama is complete.
1
5
ANGLE
DIRECTION
R Shooting ends if the shutter button is pressed all
the way down during shooting. No panorama
may be recorded if the shutter button is pressed
before the panorama is complete.
To select the size of the angle
through which you will pan the
camera while shooting, press the se-
lector left. Highlight a size and press MENU/OK.
2
The size of the completed panorama varies with
the angle and pan direction.
Press the selector right to view a
choice of pan directions. Highlight
a pan direction and press MENU/OK.
3
4
Angle
Pan diirection
Horizontal
Vertical
Size (W × H)
5,120×1,440/ 7.3M
2,160×5,120/11.1M
7,680×1,440/11.1M
2,160×7,680/16.6M
P
Press the shutter button all the way down to
start recording. There is no need to keep the
shutter button pressed during recording.
Horizontal
Vertical
O
37
Panoramas
Q Panoramas are created from multiple frames; expo-
sure for the entire panorama is determined by the
first frame. The camera may in some cases record an
greater or lesser angle than selected or be unable to
stitch the frames together perfectly. The last part of
the panorama may not be recorded if shooting ends
before the panorama is complete.
Q Shooting may be interrupted if the camera is panned
too quickly or too slowly. Panning the camera in a
direction other than that shown cancels shooting.
Q The desired results may not be achieved with mov-
ing subjects, subjects close to the camera, unvary-
ing subjects such as the sky or a field of grass, sub-
jects that are in constant motion, such as waves and
waterfalls, or subjects that undergo marked chang-
es in brightness. Panoramas may be blurred if the
subject is poorly lit.
For Besst Results
For best results, use a lens with a focal length of
35mm or less (50mm or less in 35mm format). Prop
your elbows against your sides and move the camera
slowly in a small circle at a steady speed, keeping the
camera horizontal and being careful only to pan in
the direction shown by the guides. Use a tripod for
best results. If the desired results are not achieved, try
panning at a different speed.
38
FRecording High-DDefinition (HDD)) MMovies
Record short high-definition movies. Sound is recorded in stereo via the built-in microphone; during
recording, do not cover the microphone or use the viewfinder selector, which is located next to the
microphone.
R Focus, exposure, and white balance are adjusted
automatically throughout recording. The color and
brightness of the image may vary from those dis-
played before recording begins.
R The indicator lamp lights while movies are being
recorded.
Press the DRIVE button to display
drive options. Press the selector up
or down to highlight F(MOVIE)
and press MENU/OK.
1
Q The microphone may pick up lens noise and other
sounds made by the camera during recording.
Q Vertical or horizontal streaks may appear in movies
containing very bright subjects. This is normal and
does not indicate a malfunction.
MOVE
Q If the optical viewfinder is on, the camera will au-
tomatically switch to the electronic viewfinder.
Press the shutter button all the way
down to start recording.
2
3
Press the shutter button all the way
down again to end recording. Re-
cording ends automatically after ten
minutes or when memory is full.
39
FRecording High-Definition (HD) Movies
Before Recording
Before recording, choose a frame size of i1920 (1,920 × 1,080, or Full HD) or h1280 (1,280 × 720,
orHD)usingtheWMOVIEMODEoptionintheshootingmenu(P73), adjustaperture(P26), white
balance (P32), film simulation (P51), and exposure compensation (P29), and select a focus mode
(P45).
R To increase zoom by 3× for a focal length equivalent to 105mm (35mm format), press the kbutton before
recording begins. Press nto cancel zoom.
Q Continuous AF is used when S is selected for focus mode.
40
hUsing thee Selff-Timer
Use the timer for self-portraits or to prevent blur caused by camera shake.
P
Press MENU/OK in shooting mode to display the shooting menu. Press
the selector up or down to highlight BSELF-TIMER and press MENU/
OK.
1
EXIT
P
Press the selector up or down to highlight one of the following op-
2
tions and press MENU/OK to select.
Option
Description
The shutter is released two seconds after the shutter button is pressed. Use
R2 SEC to reduce blur caused by the camera moving when the shutter button is
pressed.
The shutter is released ten seconds after the shutter button is pressed. Use
for photographs in which you wish to appear yourself.
S10 SEC
OFF
Self-timer off.
Press the shutter button halfway to focus.
3
Q Stand behind the camera when using the shutter button. Standing in
front of the lens can interfere with focus and exposure.
41
hUsing the Self-Timer
Press the shutter button the rest of the way down to start the timer.
4
The display in the monitor shows the number of seconds remaining
until the shutter is released. To stop the timer before the picture is
taken, press DISP/BACK.
The self-timer lamp on the front of the camera will blink immediately
before the picture is taken. If the two-second timer is selected, the
self-timer lamp will blink as the timer counts down.
R The self-timer turns off automatically when the camera is turned off.
42
Focus/Expossure Lock
To compose photographs with off-center subjects:
Focus: Position the subject in the focus frame and press the shutter button half-
way to lock focus and exposure. Focus and exposure will remain locked while
the shutter button is pressed halfway (AF/AE lock).
1
R Depending on the option selected for vAE/AF-LOCK BUTTON in the shooting menu (P72), focus and/
or exposure can also be locked by pressing the AFL/AEL button; focus and/or exposure will remain locked
even if the shutter button is pressed. Choose AE LOCK ONLY to lock exposure but not focus, AF LOCK
ONLY to lock focus but not exposure, or AE/AF LOCK to lock both focus and exposure. In manual focus
mode (P45), the camera will focus automatically with the AFL/AEL button.
Recompose: Keep the shutter button pressed halfway or keep the AFL/AEL button
pressed.
2
3
R If AE&AF ON/OFF SWITCH is selected for kAE/AF-LOCK MODE (P72), focus and/or
exposure lock when the AFL/AEL button is pressed and remain locked until the button
is pressed again.
Shoot: Press the button all the way down.
43
Focus/Exposure Lock
Autoffocus
Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects listed
below.
• Very shiny subjects such as mirrors or car bodies.
• Fast-moving subjects.
• Subjects photographed through a window or other reflective object.
• Dark subjects and subjects that absorb rather than reflect light, such as hair or fur.
• Insubstantial subjects, such as smoke or flame.
• Subjects that show little contrast with the background (for example, subjects in clothing that is the same color
as the background).
• Subjects positioned in front of or behind a high-contrast object that is also in the focus frame (for example, a
subject photographed against a backdrop of highly contrasting elements).
44
Focus MMode
Use the focus mode selector to choose how the camera focuses.
• S (single AF): Focus locks while the shutter button is pressed halfway.
Choose for stationary subjects.
• C (continuous AF): Focus is continually adjusted to reflect changes in the
distance to the subject even when the shutter button is not pressed
halfway (note that this increases the drain on the battery).
• M (manual): Focus manually using the focus ring. Rotate the ring left to reduce the focus distance,
right to increase. The manual focus indicator indicates how closely the focus distance matches the
distance to the subject in the focus brackets (the red bar indicates the focus distance, the white bar
the depth of field, or in other words the distance in front of and behind the focus point that ap-
pears to be in focus); you can also check focus visually in the electronic viewfinder or LCD monitor.
Choose for manual control of focus or in situations in which the camera is unable to focus using
autofocus (P44).
Focus distance
(red bar)
A
16 11
8
5.6
4
2.8
Manual focus
mode icon
Reduce focus
distance
Increase focus
distance
Manual focus
indicator
Depth of field
(white bar)
R Use the IFOCUS RING option in the setup menu (P81) to reverse the direction of rotation of the focus ring.
R The camera will not focus if the focus ring is rotated past infinity.
R To focus using autofocus, press the AFL/AEL button. This can be used to quickly focus on a chosen subject in
manual focus mode.
R The camera can show focus distance in meters or feet. Use the MFOCUS SCALE UNITS option in the setup
menu (P83) to choose the units used.
45
Focus Mode
Maannuall Focuss
Pressing the center of the command dial magnifies the view in the electronic
viewfinder or LCD monitor for precise focus. To scroll to other areas of the
frame, press the AF button and use the selector.
46
Focus Frame Selection
When tAREA is selected for FAF MODE in the shooting
menu and S is selected for focus mode, the electronic viewfinder
and LCD monitor offer a choice of 49 focus points and the opti-
cal viewfinder a choice of 25, allowing photographs to be com-
posed with the main subject positioned almost anywhere in the
frame. To position the focus frame, press the AF button and use
the selector (the focus frame can be returned to the center by
pressing MENU/OK). Press the AF button again to put the setting
into effect.
Focus point
Focus frame
EVF/LCD
Q When you switch to the optical viewfinder, the camera will select the
focus frame closest to that selected in the electronic viewfinder or
LCD monitor.
OVF
When framing pictures in the electronic viewfinder or LCD moni-
tor, you can choose the size of the focus frame for S by pressing
the AF button and rotating the command dial left or right. Rotate
the dial left to reduce the frame by up to 50%, right to enlarge it
by up to 150%, or press the center of the dial to restore the frame
to its original size. Press the AF button again to put the setting
into effect.
EVF/LCD
47
Sensitiivviitty
“Sensitivity” refers to the camera’s sensitivity to light. Choose from values between L (100) (ISO 100)
and H (25600) (ISO 25600). Higher values can be used to reduce blur when lighting is poor, while low-
er values allow slower shutter speeds or wider apertures in bright light; note, however, that mottling
may appear in pictures taken at high sensitivities, particularly at H (25600), while choosing L (100)
reduces dynamic range. Values of from ISO 200 to ISO 6400 are recommended in most situations. If
an AUTO option is selected, the camera will adjust sensitivity automatically in response to shooting
conditions; the value in parentheses is the maximum sensitivity that will be selected when the subject
is poorly lit.
P
Press MENU/OK in shooting mode to display the shooting menu. Press
the selector up or down to highlight NISO and press MENU/OK.
1
R At default settings, ISO options can also be displayed by pressing the Fn
button.
EXIT
P
Press the selector up or down to highlight the desired option and
press MENU/OK to select.
2
R Sensitivity is not reset when the camera is turned off.
R L (100) is reset to ISO 200 and H (12800) and H (25600) are reset to ISO 6400 when RAW, FINE+RAW, or
NORMAL+RAW is selected for image quality (P53, 67). For more information on the settings available with
L (100), H (12800), and H (25600), see page 116.
48
Meettering
To choose how the camera meters exposure, press the AE button
to display metering options. Use the selector to highlight an op-
tion and press AE to select.
Mode
Description
The camera instantly determines exposure based on an analysis of
composition, color, and brightness distribution. Recommended in
most situations.
o
(MULTI)
The camera meters lighting conditions in an area at the center of
the frame equivalent to 2% of the total. Recommended when the
background is much brighter or darker than the main subject; due to
parallax, not recommended when pictures are framed in the optical
viewfinder.
p
MULTI
OVF
EVF/LCD
(SPOT)
Exposure is set to the average for the entire frame. Provides consistent
exposure across multiple shots with the same lighting, and is particu-
q
(AVERAGE) larly effective for landscapes and portraits of subjects dressed in black
or white.
49
The Fn BBuutttton
The role played by the Fn button can be selected using the FFn
BUTTON option in the shooting menu (P70). The options available
include multiple exposure (P36), depth-of-field preview (P26), the
self-timer (P41), sensitivity (P48), image size (P67), image quality
(P67), dynamic range (P68), film simulation (P51), white balance
(P32),AFmode(P69),movierecording(P39),RAW/JPEGtoggle(P53),andcustomsettings(P52).
R The FFn BUTTON menu can also be displayed by pressing and holding the Fn button.
50
Film Simulation
Simulate the effects of different kinds of film, including black-and-white (with or without color filters).
P
Press MENU/OK in shooting mode to display the shooting menu. Press
the selector up or down to highlight PFILM SIMULATION and
press MENU/OK.
1
EXIT
Press the selector up or down to highlight one of the following options and press MENU/OK to select.
2
Option
Description
c(PROVIA/STANDARD)
Standard color reproduction. Suited to a wide range of subjects, from portraits to landscapes.
A high-contrast palette of saturated colors, suited to nature photos.
>
(Velvia/VIVD)
Enhances the range of hues available for skin tones in portraits while preserving the bright blues
of daylight skies. Recommended for outdoor portrait photography.
e(ASTIA/SOFT)
Offers slightly more contrast than h (PRO Neg. Std). Recommended for outdoor portrait pho-
tography.
g
(PRO Neg. Hi)
A soft-toned palette. The range of hues available for skin tones is enhanced, making this a good
choice for studio portrait photography.
h
(PRO Neg. Std)
;
(MONOCHROME)
Take pictures in standard black and white.
Take black-and-white pictures with slightly increased contrast. This setting also slightly tones
down the brightness of the sky.
e(MONOCHROME + Ye FILTER)
Take black-and-white pictures with increased contrast. This setting also tones down the bright-
ness of the sky.
d(MONOCHROME + R FILTER)
f(MONOCHROME + G FILTER) Soften skin tones in black-and-white portraits
f(SEPIA)
Take pictures in sepia.
R Film simulation options can be combined with tone and sharpness settings (P69).
51
Saving Settings
Save up to three sets of custom camera settings for commonly-encountered situations. Saved settings
can be recalled using the uSELECT CUSTOM SETTING option in the shooting menu.
P
Press MENU/OK in shooting mode to display the shooting menu. Press
the selector up or down to highlight KEDIT/SAVE CUSTOM SET-
TING and press MENU/OK.
1
EXIT
Highlight a custom settings bank and press MENU/OK to select. Adjust
the following as desired and press DISP/BACK when adjustments are com-
plete: NISO, UDYNAMIC RANGE, PFILM SIMULATION, DWHITE
BALANCE, fCOLOR, qSHARPNESS, rHIGHLIGHT TONE,
sSHADOW TONE, and hNOISE REDUCTION.
2
R To replace the settings in the selected bank with the settings currently selected with the camera, select
KSAVE CURRENT SETTINGS and press MENU/OK.
A confirmation dialog will be displayed; highlight OK and press MENU/
OK.
3
52
Recording Pictures in RAW Format
To toggle RAW image quality on or off for a single shot, assign RAW
to the Fn button (P50). If a JPEG option is currently selected for im-
age quality, pressing the Fn button temporarily selects the equivalent
JPEG+RAW option. If a JPEG+RAW option is currently selected, pressing
the Fn button temporarily selects the equivalent JPEG option, while if
RAW is selected, pressing the Fn button temporarily selects FINE. Taking a picture or pressing the Fn
button again restores the previous setting.
R RAW images record raw, unprocessed data from the camera image sensor. JPEG copies of RAW images can
be created using the jRAW CONVERSION option in the playback menu, or RAW images can be viewed on
a computer using the RAW File Converter application that is installed with the software on the supplied CD
(P90, 92).
R Sensitivities of L (100), H (12800), and H (25600) are not available when RAW image quality is on (P48).
R Control lock (P4) disables the RAW button. To enable the RAW button, press MENU/OK until the X icon clears
from the display.
53
NFlash Phhotoography
Optional EF-42, EF-20, and EF-X20 shoe-mounted flash units (P97) can be used for additional lighting
when shooting at night or indoors under low light. See the manual provided with the flash unit for
details.
P
To choose the flash mode for the optional flash unit, select IFLASH MODE in the
shooting menu. The options shown below will be displayed; press the selector up
or down to highlight an option and press MENU/OK to select.
Mode
Description
AUTO (AUTO FLASH)/
The flash fires when required. Recommended in most situations.
K(RED EYE REDUCTION)*
N(FORCED FLASH)/ The flash fires whenever a picture is taken. Use for backlit subjects or for natural
L(FORCED FLASH)* coloration when shooting in bright light.
The flash does not fire even when the subject is poorly lit. Use of a tripod is rec-
ommended.
P(SUPPRESSED FLASH)
l (2ND CURTAIN SYNC.)/
The flash fires immediately before the shutter closes.
d(2ND CURTAIN SYNC.)*
O(SLOW SYNCHRO)/ Capture both the main subject and the background under low light (note that
M(RED-EYE & SLOW)* brightly lit scenes may be overexposed).
* Red-eye removal (K, L, M, or d) is available in these modes when ON is selected for
BRED EYE REMOVAL in the shooting menu (P73). Red-eye removal minimizes“red-eye”
caused when light from the flash is reflected from the subject’s retinas as shown in the il-
lustration at right.
R If pis displayed when the shutter button is pressed halfway, the flash will fire when the photo is taken.
R The flash may fire several times with each shot. Do not move the camera until shooting is complete.
R Remove lens hoods to prevent shadows in photos taken with the flash.
Q The flash does not fire in silent mode.
54
Flash Photography
Fllash Sync Speed
/
The flash will synchronize with the shutter at shutter speeds of 1 180s or slower.
Thhee Sync Terminal
Use the sync terminal to connect flash units that require a sync cable.
Thhiirrdd--PPaarrtty Fllaasshh UUnnits
Do not use third-party flash units that apply over 300V to the camera hot shoe.
55
Viewing Pictures
Viewing Pictures Full Frame
Pictures can be viewed in the electronic viewfinder or LCD monitor. When taking important pictures,
take a test shot and check the results.
To view pictures full frame, press a.
Deletingg Piccttuurres
To delete the current picture, press the b button.
The following dialog will be displayed.
3
Additional pictures can be viewed by
pressing the selector left or right or ro-
tating the command dial. Press the se-
lector or rotate the dial right to view pictures in
the order recorded, left to view pictures in reverse
order. Keep the selector pressed to scroll rapidly
to the desired frame.
To delete the picture, highlight OK and
press MENU/OK. To exit without deleting
the picture, highlight CANCEL and press
MENU/OK.
R Pictures can also be deleted from the playback
menu (P65).
R Pictures taken using other cameras are indicated by
Creatingg JPEEGG CCopies of RAW PPicttuurres
Pressing the RAW button during playback displays
RAW conversion options (P53).
a m(“gift image”) icon during playback.
Favorittes: Rattinngg PPiiccttuurres
To rate the current picture, press DISP/BACK and press
the selector up and down to select from zero to five
stars.
56
Viewing Pictures Full Frame
Viewing Photo Information
The photo information display changes
each time the selector is pressed up.
Playback Zoom
Press kto zoom in on the current picture, nto
zoom out. When the picture is zoomed in, the
selector can be used to view areas of the image
not currently visible in the display. Press DISP/BACK
or MENU/OK to exit zoom.
Zoom indicator
Basic data
Details, page 1
Navigation window shows
portion of image currently
displayed
R The maximum zoom ratio varies with image size
(P67). Playback zoom is not available with cropped
or resized copies saved at a size of a.
Active focus point (“+”)
Details, page 2
R Rotate the command dial to view other images.
Zoooommiinngg iinn oonn tthe Focus Point
Press the center of the command
control to zoom in on the focus
point. Press the center of the com-
mand control again to return to
full-frame playback.
57
Viewing Pictures Full Frame
Multi-Frame Playback
To change the number of images displayed, press nwhen a picture is displayed full frame.
Press nto view
more images.
Press kto view
fewer images.
Use the selector to highlight images and press MENU/OK to view the highlighted image full frame. In
the nine- and hundred-frame displays, press the selector up or down to view more pictures.
58
Viewingg Movvies
Movie icon
During playback, movies are displayed as shown at right. The following operations
can be performed while a movie is displayed:
Operation
Description
Press the selector down to start playback. Press again to pause. While playback is
Start/pause playback paused, you can press the selector left or right to rewind or advance one frame
at a time.
End playback
Press the selector up to end playback.
Press the selector left or right to adjust playback speed during playback. Speed is
shown by the number of arrows (M or N).
Adjust speed
Press MENU/OK to pause playback and display volume controls. Press the selector
up or down to adjust the volume; press MENU/OK again to resume playback. Vol-
ume can also be adjusted in the playback menu (P78).
Adjust volume
Progress bar
Progress is shown in the display during playback.
Q Do not cover the speaker during playback.
Q Sound is not played back in silent mode.
59
Immaage SSearch
Follow the steps below to search for pictures.
Press MENU/OK during playback to display the playback menu. Press the selector up or down to
highlight bIMAGE SEARCH and press MENU/OK.
1
2
Highlight an option and press MENU/OK.
Option
BY DATE
BY FACE
Description
Search by date.
Search for pictures that include faces.
BY I FAVORITES Search by rating.
BY TYPE OF DATA Find all still pictures, all movies, all pictures taken in burst mode, or all RAW pictures.
BY UPLOAD MARK Find all pictures selected for upload to a specified destination.
Option
AERASE
DPROTECT
ISLIDE SHOW
See page
65
75
Select a search condition. Only pictures that match the search condition
3
4
will be displayed. To delete or protect selected pictures or to view the se-
lected pictures in a slide show, press MENU/OK and choose from the options
at right.
76
To end the search, select EXIT SEARCH.
60
mPhotooBBoook Assist
Create books from your favorite photos.
Creating a PhotoBook
Select NEW BOOK for mPHOTOBOOK AS-
SIST in the playback menu (P77) and choose
from the following options:
• SELECT FROM ALL: Choose from all available
pictures.
Select COMPLETE PHOTOBOOK (to select all
photos or all photos matching the specified
search conditions for the book, choose SE-
LECT ALL). The new book will be added to
the list in the photobook assist menu.
1
3
• SELECT BY IMAGE SEARCH: Choose from pictures
matching selected search conditions (P60).
Q Books can contain up to 300 pictures.
Q Books that contain no photos are automatically de-
leted.
R Neither photographs a or smaller nor movies
can be selected for photobooks.
Scroll through the images and press the se-
lector up to select or deselect. To display the
current image on the cover, press the selector
down. Press MENU/OK to exit when the book is
complete.
2
R The first picture selected becomes the cover im-
age. Press the selector down to select a different
image for the cover.
61
mPhotoBook Assist
Viewing Photobooks
Editing and Deleting Photobooks
Highlight a book in the photobook assist menu Display the photobook and press MENU/OK. The
and press MENU/OK to display the book, then press following options will be displayed; select the
the selector left or right to scroll through the pic- desired option and follow the on-screen instruc-
tures.
tions.
• EDIT: Edit the book as described in “Creating a
PhotoBook”(P61).
• ERASE: Delete the book.
Photoobooks
Photobooks can be copied to a computer using the supplied MyFinePix Studio software (P90).
62
Viewing Panoramas
If you press the selector down when a panorama is dis-
played full frame, the camera will play back the picture from
left to right or from bottom to top. Press the selector down
to pause and resume playback, or press the dial up to return
to full-frame playback. To rewind or advance one frame at a
time, press the selector left or right while playback is paused.
63
Viewing Pictures Taken in a Single Burst
Position in burst/total number
of pictures in burst
When a picture taken in continuous shooting mode is dis-
played full frame, the first picture in the current burst can
be viewed by pressing the selector down (burst mode play-
back). Press the dial right to view pictures in the order re-
corded, left to view pictures in reverse order. Keep the dial
pressed to scroll rapidly to the desired frame. To exit, press
DISP/BACK.
First picture in burst
R Pressing the selector right when the last picture in the burst is displayed displays the first picture in the burst;
similarly, pressing the dial left when the first picture is displayed displays the last picture.
R Deletion (P65), rotation (P75), and protect (P75) operations applied during burst mode playback apply
only to the current picture. In contrast, if these operations are performed when a picture taken in continuous
shooting mode is displayed in single-frame playback, all images in the same burst will be affected.
Bursts That Cross Folders
If a single burst is spread across multiple folders, the pictures in each folder will be treated as separate bursts.
Viewing Photo Information
To view photo information for a picture taken in continuous shooting mode, display it in burst mode playback.
Photo information for pictures taken in continuous shooting mode can not be viewed during single-frame
playback.
64
xDeleting Pictures
The AERASE option in the playback menu can be used to delete individual pictures, multiple select-
ed pictures, or all pictures. Note that deleted pictures can not be recovered. Copy important pictures to
a computer or other storage device before proceeding.
Press MENU/OK during playback to display the playback menu, then press the se-
lector up or down to highlight AERASE and press right to display the following
options. Press the selector up or down to highlight an option and press MENU/OK
to select.
Option
FRAME
Description
Press the selector left or right through pictures and press MENU/OK to delete the current picture (a confirmation
dialog is not displayed)
Highlight pictures and press MENU/OK to select or deselect (pictures that in a photobook or print order are
SELECTED FRAMES shown by S). When the operation is complete, press DISP/BACK to display a confirmation dialog, then high-
light OK and press MENU/OK.
A confirmation dialog will be displayed; highlight OK and press MENU/OK to delete all unprotected pictures.
Pressing DISP/BACK cancels deletion; note that any pictures deleted before the button was pressed can not be
ALL FRAMES
recovered.
R Protected pictures can not be deleted. Remove protection from any pictures you wish to delete (P75).
R If a message appears stating that the selected images are part of a DPOF print order, press MENU/OK to delete
the pictures.
65
Crreeaattiing JPEG Copiess of RAAWW PPiiccttuurreess
RAW pictures store information on camera settings separately from the data captured by the camera
image sensor. Using the jRAW CONVERSION option in the playback menu, you can create JPEG
copies of RAW pictures using different options for the settings listed below. The original image data
are unaffected, allowing a single RAW image to be processed in a multitude of different ways.
Setting
Description
Press MENU/OK during playback to display the
playback menu, then press the selector up
or down to highlight jRAW CONVERSION
and press MENU/OK to display the settings list-
ed in the table at right.
1
REFLECT SHOOTING Create a JPEG copy using the settings in ef-
COND.
PUSH/PULL
PROCESSING
fect at the time the photo was taken.
Adjust exposure by –1EV to +3EV in incre-
ments of 1 3EV (P29).
Enhance details in highlights for natural
/
DYNAMIC RANGE
FILM SIMULATION
contrast (P68).
R If RAW is assigned to the Fn button (P53), these
options can also be displayed by pressing Fn
during playback.
Simulate the effects of different types of film
(P51).
WHITE BALANCE Adjust white balance (P32).
WB SHIFT
COLOR
SHARPNESS
Fine-tune white balance (P32).
Adjust color density (P68).
Sharpen or soften outlines (P69).
Press the selector up or
down to highlight a setting
and press the dial right to
select. Press the dial up or
2
3
HIGHLIGHT TONE Adjust highlights (P69).
SHADOW TONE Adjust shadows (P69).
NOISE REDUCTION Process the copy to reduce mottling (P69).
down to highlight the de-
sired option and press MENU/OK to select and
return to the settings list. Repeat this step to
adjust additional settings.
Choose the color space used for color repro-
duction (P83).
COLOR SPACE
Press the Q button to preview the JPEG copy
and press MENU/OK to save.
66
Menus
Using the MMenus: Shhoooottiinngg MMode
P
The shooting menu is used to adjust settings for a wide range of shooting condi-
tions. To display the shooting menu, press MENU/OK in shooting mode. Highlight
items and press the selector right to view options, then highlight an option and
press MENU/OK. Press DISP/BACK to exit when settings are complete.
X
Shooting Menu Options
NISO
(defaults to 200)
Control the camera’s sensitivity to light (P48).
OIMAGE SIZE
(defaults to O3 : 2)
Option Prints at sizes up to
O3 : 2 41 × 28 cm (16 × 11 in.) Q3 : 2 21 × 14 cm (8 × 6 in.)
O16 : 9 41 × 23 cm (16 × 9 in.) Q16 : 9 21 × 12 cm (8 × 5 in.)
O1 : 1 28 × 28 cm (11 × 11 in.) Q1 : 1 14 × 14 cm (6 × 6 in.)
P3 : 2 29 × 20 cm (12 × 8 in.)
Choose the size and aspect ratio at which still pictures are recorded.
Option Prints at sizes up to
Aspect Ratio
Pictures wiith an asspect raatio of 3::2 have tthe same pproporttions as
a frame of 35mm film, while an aspect ratio of 16:9 is suited to
display onn High Definition (HD) devviiccees.. PPiiccttuures wiith an aaspect
ratio of 1:1 are square.
P16 : 9 29 × 16 cm (12 × 6 in.)
P1 : 1 20 × 20 cm (8 × 8 in.)
O IMAGE SIZE is not reset when the camera is turned off or an-
other shooting mode is selected.
TIMAGE QUALITY
(defaults to FINE)
Choose a file format and compression ratio. Select FINE or NORMAL to record JPEG images, RAW to record RAW images, or
FINE+RAW or NORMAL+RAW to record both JPEG and RAW images. FINE and FINE+RAW use lower JPEG compression ratios
for higher-quality JPEG images, while NORMAL and NORMAL+RAW user higher JPEG compression ratios to increase the num-
ber of images that can be stored.
67
Using the Menus: Shooting Mode
UDYNAMIC RANGE
(defaults to A)
Control contrast. Choose lower values to increase contrast when shooting indoors or under overcast skies, higher values to
reduce loss of detail in highlights and shadows when photographing high-contrast scenes. Higher values are recommended
for scenes that include both sunlight and deep shade, for such high-contrast subjects as sunlight on water, brightly-lit autumn
leaves, and portraits taken against a blue sky, and for white objects or people wearing white; note, however, that mottling may
appear in pictures taken at higher values.
R If AUTO is selected, shutter speed and aperture will be displayed when the shutter button is pressed halfway.
R B200% is available at sensitivities of ISO 400 and above, C400% at sensitivities of ISO 800 and above.
PFILM SIMULATION
(defaults to <)
Simulate the effects of different types of film (P51).
XFILM SIMULATTION BKT
Choose film types for film simulation bracketing (P35).
BSELF-TIMER
Take pictures with the self-timer (P41).
(defaults to OFF)
(defaults to AUTO)
(defaults to MID)
DWHITE BAALLANCE
Adjust colors to match the light source (P32).
fCOLOR
Adjust color density.
68
Using the Menus: Shooting Mode
qSHARPNESS
(defaults to STANDARD)
Sharpen or soften outlines.
rHIGHLIGHT TONE
Adjust the appearance of highlights.
(defaults to STANDARD)
(defaults to STANDARD)
(defaults to STANDARD)
(defaults to ON)
sSHADOW TONE
Adjust the appearance of shadows.
hNOISE REDUCTION
Reduce noise in pictures taken at high sensitivities.
KLONG EXPOSURE NR
Select ON to reduce mottling in long time-exposures (P28).
uSELECT CUSTOM SETTING
Recall settings saved with KEDIT/SAVE CUSTOM SETTING.
KEDIT/SAVE CUSTOM SETTING
Save settings (P52).
FAF MODE
(defaults to tAREA)
Choose how the camera selects the focus area when in focus mode S.
• sMULTI: When the shutter button is pressed halfway, the camera detects high-contrast subjects and selects the focus area
automatically.
• tAREA: Choose the focus area manually (P47).
69
Using the Menus: Shooting Mode
GCORRECTEED AF FRAME
(defaults to OFF)
If ON is selected, a second focus frame for focus distances of about 80cm (2.6ft) will be added to the display in the optical view-
finder. The focus frame for the current focus distance is displayed in green when the shutter button is pressed halfway.
ON
OFF
Focus frame for focus distance of infinity
Focus frame
Focus frame for focus distance of
about 80 cm (2.6 ft)
lFOCAL LENGTH SETTING
(defaults to 50 mm)
Enter lens focal length when using a lens that does not supply the focal length to the camera. Choose from LENS 1 (21 mm),
LENS 2 (24 mm), LENS 3 (28 mm), LENS 4 (35 mm), LENS 5 (50 mm), and LENS 6 (75 mm). The focal length for lenses 5 and 6
can be chosen by rotating the command dial; the focal lengths for the remaining options are fixed at the value given in brackets.
mSHOOT WITHOUT LENS
Choose whether shutter release is enabled when no lens is attached.
(defaults to OFF)
(defaults to NISO)
(defaults to OFF)
FFn BUTTON
Choose the role played by the Fn button (P50).
nMULTIPLE EXPOSURE
Create a photograph that combines two exposures (P36).
70
Using the Menus: Shooting Mode
vDISP. CUSTOM SETTING
Choose the items displayed in the optical viewfinder or in the electronic viewfinder and LCD monitor (P21). The following items
can be displayed: framing grid (you can also select the grid type as described on page 71), virtual horizon, focus distance (auto or
manual), histogram, exposure (shutter speed, aperture, and sensitivity), exposure compensation/exposure indicator, metering,
flash mode, white balance, film simulation, dynamic range, number of exposures remaining, image size and quality, and battery
level. See pages 6–8 for the locations of these items in the displays.
Highlight OVF or EVF/LCD and press MENU/OK.
1
2
Press the selector up or down to highlight items and press MENU/OK to select or deselect. Press DISP/BACK to exit when settings
are complete.
Virtuall Horizon
Seelleeccttingg ELECTRONIC LEVEL dispplays a virttual hhorizzoonn.. TThe cameraa is leevveell wwhheenn tthhee ttwwoo lliinneess oover-
lap.
R The virtual horizon may not be displayed if the camera lens is pointed up or down.
cFRAMING GUIDLINE
Choose the type of framing grid available in shooting mode.
(defaults to FGRID 9)
HHD FRAMING
FGRID 9
GGRID 24
For “rule of thirds” composition.
A six-by-four grid.
Frame HD pictures in the crop shown by the
lines at the top and bottom of the display.
71
Using the Menus: Shooting Mode
CAF ILLUMINATOR
(defaults to ON)
If ON is selected, the AF-assist illuminator will light to assist autofocus.
R The AF-assist illuminator turns off automatically in silent mode.
Q The camera may be unable to focus using the AF-assist illuminator in some cases. If the camera is unable to focus in macro
mode, try increasing the distance to the subject.
Q Avoid shining the AF-assist illuminator directly into your subject’s eyes.
kAE/AF-LOCK MODE
(defaults to AE & AF ON WHEN PRESSING)
If AE & AF ON WHEN PRESSING is selected, exposure and/or focus will lock while the AFL/AEL button is pressed. If AE & AF ON/
OFF SWITCH is selected, exposure and/or focus will lock while the AFL/AEL button is pressed and remain locked until the button
is pressed again.
vAE/AF-LOCK BUTTON
(defaults to AE LOCK ONLY)
Choose the role played by the AFL/AEL button (P43).
mAUTOROTATE PB
(defaults to ON)
Choose ON to automatically rotate“tall”(portrait-orientation) pictures during playback.
pFLAASHH MODE
Choose a flash mode for optional flash units (P54).
IFLASH
(defaults to 0)
/
/
Adjust flash brightness. Choose from values between +2 3EV and –2 3EV. Note that the desired results may not be achieved
depending on shooting conditions and the distance to the subject.
72
Using the Menus: Shooting Mode
BRED EYE RREMOVAL
(defaults to OFF)
Choose ON to remove red-eye effects caused by the flash.
R Red-eye reduction is performed only when a face is detected.
R Red-eye removal is not available with RAW images.
nSAVE ORG IMAGE
(defaults to OFF)
Choose ON to save unprocessed copies of pictures taken using BRED EYE REMOVAL.
WMOVIE MODE
(defaults to i)
Choose a frame size for movie recording (P39).
73
Using the MMenus: Playbbaacckk MMode
To display the playback menu, press MENU/OK in playback mode. Highlight items
and press the selector right to view options, then highlight an option and press
MENU/OK. Press DISP/BACK to exit when settings are complete.
XT
Playback Menu Options
jRAW CONVVERSION
Create JPEG copies of RAW pictures (P56).
AERASE
Delete all or selected pictures (P65).
GCROP
Create a cropped copy of the current picture.
Display the desired picture.
1
Select GCROP in the playback menu.
2
3
Use the kand nbuttons to zoom in and out and press the selector up, down, left, or right to scroll the picture until the
desired portion is displayed.
Press MENU/OK to display a confirmation dialog.
4
5
Press MENU/OK again to save the cropped copy to a separate file.
R Larger crops produce larger copies; all copies have an aspect ratio of 3:2. If the size of the final copy will be a, OK will be
displayed in yellow.
74
Using the Menus: Playback Mode
eRESIZE
Create a cropped copy of the current picture.
Display the desired picture.
1
Select eRESIZE in the playback menu.
2
3
4
Highlight a size and press MENU/OK to display a confirmation dialog.
Press MENU/OK again to save the resized copy to a separate file.
R The sizes available vary with the size of the original image.
DPROTECT
Protect pictures from accidental deletion. Highlight one of the following options and press MENU/OK.
• FRAME: Protect selected pictures. Press the selector left or right to view pictures and press MENU/OK to select or deselect. Press
DISP/BACK when the operation is complete.
• SET ALL: Protect all pictures.
• RESET ALL: Remove protection from all pictures.
Q Protected pictures will be deleted when the memory card is formatted (P83).
CIMAGE ROTATE
Rotate pictures.
Display the desired picture.
1
Select CIMAGE ROTATE in the playback menu.
2
3
4
Press the selector down to rotate the picture 90 ° clockwise, up to rotate it 90 ° counterclockwise.
Press MENU/OK. The picture automatically be displayed in the selected orientation whenever it is played back on the camera.
R Protected pictures can not be rotated. Remove protection before rotating pictures (P75).
R The camera may not be able to rotate pictures created with other devices.
R Pictures taken with mAUTOROTATE PB are automatically displayed in the correct orientation during playback (P72).
75
Using the Menus: Playback Mode
BRED EYE RREMOVAL
Remove red-eye from portraits. The camera will analyze the image; if red-eye is detected, the image will be processed to create
a copy with reduced red-eye.
Display the desired picture.
1
Select BRED EYE REMOVAL in the playback menu.
2
Press MENU/OK.
3
R Red eye may not be removed if the camera is unable to detect a face or the face is in profile. Results may differ depending on
the scene. Red eye can not be removed from pictures that have already been processed using red-eye removal or pictures
created with other devices.
R The amount of time needed to process the image varies with the number of faces detected.
R Copies created with BRED EYE REMOVAL are indicated by a eicon during playback.
R Red eye removal can not be performed on RAW images.
ISLIDEE SHOW
View pictures in an automated slide show. Choose the type of show and press MENU/OK to start. Press DISP/BACK at any time dur-
ing the show to view on-screen help. The show can be ended at any time by pressing MENU/OK.
Option
NORMAL
Description
Press the selector left or right to go back or skip ahead one frame. Select FADE-IN for fade transitions between
frames.
FADE-IN
NORMAL g
FADE-IN g
As above, except that camera automatically zooms in on faces.
MULTIPLE Display several pictures at once.
R The camera will not turn off automatically while a slide show is in progress.
76
Using the Menus: Playback Mode
mPHOTOBOOK ASSIST
Create books from your favorite photos (P61).
jMARK FOR UPLOAD TO
Select pictures for upload to YouTube or Facebook using MyFinePix Studio (Windows only).
Select YouTube to choose movies for upload to YouTube, FACEBOOK to choose photos and movies for upload to Facebook.
1
2
Press the selector left or right to display pictures and press MENU/OK to select or deselect. Press DISP/BACK to exit when all the
desired pictures are selected.
R Only movies can be selected for upload to YouTube.
R During playback, selected pictures are marked with jYouTube or jFACEBOOK indicators.
R Choose RESET ALL to deselect all pictures. If the number of pictures affected is very large, a message will be displayed while
the operation is in progress. Press DISP/BACK to exit before the operation is complete.
Uploadiing Picttures (Winddowss Only)
Seelleecctteedd ppiiccttuurreess ccaann bbee uuppllooaaddeedd uussiinngg tthhee YouTube/Facebook Upload op- Select with camera
tion in MyFinePix Studio. For information on installing MyFinePix Studio aanndd
connecting the camera to a computer, see “Viewinng Pictuures onn a Compputer”
(P90).
Upload from computer
bIMAGE SEARCH
Search for pictures (P60).
KPRINT ORDER (DPOF)
Select pictures for printing on DPOF- and PictBridge-compatible devices (P87).
77
Using the Menus: Playback Mode
JDISP ASPECT
Choose how High Definition (HD) devices display pictures with an aspect ratio of 3:2
(this option is available only when an HDMI cable is connected). Select 16:9 to display
the image so that it fills the screen with its top and bottom cropped out, 3:2 to display
the entire image with black bands at either side.
16:9
3:2
16 : 9
3 : 2
IPLAAYYBBAACK VOLUME
(defaults to 7)
Control the volume for movie playback.
78
The Setup MMenu
Using the Setup Menu
Display the setup menu.
1.1 Press MENU/OK to display the menu for the current mode.
1
1.2 Press the selector left to highlight the tab for the current menu.
1.3 Press the selector down to highlight Z.
EXIT
Tab
1.4 Press the selector right to place the cursor in the setup menu.
Adjust settings.
2
Highlight items and press the selector right to view options, then highlight an option and press
MENU/OK. Press DISP/BACK to exit when settings are complete.
79
The Setup Menu
Setup Menu Options
FDATE/TIME
Set the camera clock (P18).
NTIME DIFFFERENCE
(defaults to h)
Switch the camera clock instantly from your home time zone to the local time at your destination when traveling. To specify the
difference between local time and your home time zone:
Highlight g LOCAL and press the selector right.
1
2
Use the selector to choose the time difference between local time and your home time zone. Press MENU/OK when settings
are complete.
To set the camera clock to local time, highlight g LOCAL and press MENU/OK. To set the clock to the time in your home time
zone, select h HOME. If g LOCAL is selected, g will be displayed for three seconds when the camera is turned on.
La
Choose a language (P18).
RRESET
Reset all settings except FDATE/TIME, NTIME DIFFERENCE, and OBACKGROUND COLOR to default values. Press the
selector right to display a confirmation dialog, then highlight OK and press MENU/OK.
oSILENT MODE
(defaults to OFF)
Select ON to disable the speaker, flash, and illuminator in situations in which camera sounds or lights may be unwelcome (P30).
80
The Setup Menu
BFRAME NO.
(defaults to CONTINUOUS)
New pictures are stored in image files named using a four-digit file number assigned by adding one to the
last file number used. The file number is displayed during playback as shown at right. BFRAME NO. con-
trols whether file numbering is reset to 0001 when a new memory card is inserted or the current memory
card is formatted.
Frame number
100-0001
Directory
File
number number
Option
CONTINUOUS
RENEW
Description
Numbering continues from the last file number used or the first available file number, whichever is higher.
Choose this option to reduce the number of pictures with duplicate file names.
Numbering is reset to 0001 after formatting or when a new memory card is inserted.
R If the frame number reaches 999-9999, the shutter release will be disabled (P107).
R Selecting RRESET (P80) sets BFRAME NO. to CONTINUOUS but does not reset the file number.
R Frame numbers for pictures taken with other cameras may differ.
IFOCUS RING
(defaults to XCW)
(defaults to 0)
Choose the direction in which the focus ring is rotated to increase the focus distance.
JLCD BRIGHTNESS
Control the brightness of the displays.
UPOWER SAVE MODE
(defaults to OFF)
Select ON to reduce the drain on the battery, increasing the number of pictures that can be taken on a single charge (P23).
HQUICK START MODE
(defaults to OFF)
Select ON to reduce the time needed to restart the camera after it has been turned off (P23).
81
The Setup Menu
MAUTO PPOWER OFF
(defaults to 2 MIN)
Choose the length of time before the camera turns off automatically when no operations are performed. Shorter times reduce
the drain on the battery; if OFF is selected, the camera must be turned off manually. Note that in some situations the camera
turns off automatically even when OFF is selected.
GOPERATTIONN VVOL.
Adjust the volume of the sounds produced when camera controls are operated. Choose eOFF (mute) to disable control sounds.
AIMAGE DISP.
(defaults to 1.5 SEC)
(defaults to c)
Choose how long images are displayed after shooting. Colors may differ slightly from those in the final image and “noise” mot-
tling may be visible at high sensitivities.
Option
Description
Pictures are displayed until the MENU/OK button is pressed or the shutter button is pressed halfway. To zoom
in on the active focus point, press the center of the command control; press again to cancel zoom.
CONTINUOUS
1.5 SEC
3 SEC
OFF
Pictures are displayed for three seconds (3 SEC) or 1.5 seconds (1.5 SEC) or until the shutter button is pressed
halfway.
Pictures are not displayed after shooting.
R OFF has no effect in continuous shooting mode.
VSENSOR CLEANING
Remove dust from the camera image sensor.
Option
Description
OK
Clean sensor immediately (Pxi).
WHEN SWITCHED ON Sensor cleaning is performed when the camera turns on.
Sensor cleaning is performed when the camera turns off (sensor cleaning is not however performed if the
camera turns off in playback mode).
WHEN SWITCHED OFF
R Dust that can not be removed using sensor cleaning can be removed manually (P101).
82
The Setup Menu
JCOLOR SPACE
(defaults to sRGB)
Choose the gamut of colors available for color reproduction.
Option
Description
sRGB
Recommended in most situations.
Adobe RGB For commercial printing.
cGUIDANCE DISPPLLAY
(defaults to ON)
Choose whether to display tool tips.
MFOCUS SCALE UNITS
(defaults to METERS)
Choose the units used for the focus distance indicator (P45).
OBACKGROUNND COLOORR
Choose a color scheme.
KFORMAT
Select OK to format the memory card.
Q All data—including protected pictures—will be deleted from the memory card. Be sure important files have been copied to
a computer or other storage device.
Q Do not open the battery-chamber cover during formatting.
83
Connections
Viewing Pictures on TV
To show pictures to a group, connect the camera to a TV using an HDMI cable (available separately
from third-party suppliers; note that the TV can only be used for playback, not shooting).
Turn the camera off.
1
Connect the cable as shown below.
2
Insert into HDMI
connector
Insert into HDMI mini
connector
R Be sure the connectors are fully inserted.
Tune the television to the HDMI input channel. See the documentation supplied with the televi-
sion for details.
3
Turn the camera on and press abutton. The camera monitor turns off and pictures and movies
are played back on the TV. Note that the camera volume controls have no effect on sounds played
on the TV; use the television volume controls to adjust the volume.
4
R The USB cable can not be used while an HDMI cable is connected.
R Some televisions may briefly display a black screen when movie playback begins.
84
Printing Pictures via USB
If the printer supports PictBridge, the camera can be connected directly to the printer and
pictures can be printed without first being copied to a computer. Note that depending on the
printer, not all the functions described below may be supported.
Connecting the Camera
Printing Selected Pictures
Connect the supplied USB cable as shown and
Press the selector left or right to dis-
1
1
turn the printer on.
play a picture you wish to print.
R To print one copy of the current picture, pro-
ceed directly to Step 3.
Press the selector up or down to
2
choose the number of copies (up to
99). Repeat steps 1–2 to select ad-
ditional pictures.
Turn the camera on. tUSB will be displayed
in the monitor, followed by the PictBridge dis-
play shown below at right.
2
Press MENU/OK to display a confirma-
tion dialog.
3
4
R Pictures can be printed from memory cards that has
been formatted in the camera.
R Page size, print quality, and border selections are
made using the printer.
Press MENU/OK to start printing.
85
Printing Pictures via USB
Printing the DPOF Print Order
Printinng thee DDaattee ooff RReecoorrding
To print the print order created with KPRINT
ORDER (DPOF) in the playback menu (P77):
To print the date of recording on pictures, press
DISP/BACK in the PictBridge display and select PRINT
WITH DATE s (to print pictures without the date of
recording, select PRINT WITHOUT DATE). To ensure
that the date is correct, set the camera clock before
taking pictures. Some printers do not support date
printing. See the printer manual for details.
In the PictBridge display, press DISP/
BACK to open the PictBridge menu.
1
Press the selector up or down to
highlight uPRINT DPOF.
2
Press MENU/OK to display a confirma-
tion dialog.
3
4
Press MENU/OK to start printing.
86
Printing Pictures via USB
Creating a DPOF Print Order
During PPrinting
The KPRINT ORDER (DPOF) option in the play-
back menu can be used to create a digital “print
order” for PictBridge-compatible printers or de-
vices that support DPOF.
The message shown at right is
displayed during printing. Press
DISP/BACK to cancel before all
pictures are printed (depending
on the printer, printing may end
before the current picture has
printed).
DPOF
DPOF (Digital Print Order Format) is stan-
dard that allows pictures to be printed from
“print orders” stored on the memory card.
The information in the order includes the
pictures to be printed and the number of copies of
each picture.
If printing is interrupted, turn the camera off and
then on again.
Disconnecting thhee CCamera
Confirm that the above message is not displayed and
turn the camera off. Disconnect the USB cable.
87
Printing Pictures via USB
■ WITH DATE s/ WITHOUT DATE
Repeat steps 1–2 to complete the
print order. Press MENU/OK to save
the print order when settings are
complete, or DISP/BACK to exit with-
out changing the print order.
3
4
To modify the DPOF print order, select KPRINT
ORDER (DPOF) in the playback menu and press
the selector up or down to highlight WITH
DATE s or WITHOUT DATE.
WITH DATE s: Print date of recording
on pictures.
The total number of prints is dis-
played in the monitor. Press MENU/
OK to exit.
WITHOUT DATE: Print pictures without
date.
The pictures in the current
print order are indicated by a
u icon during playback.
Press MENU/OK and follow the steps below.
Press the selector left or right to dis-
1
play a picture you wish to include in
or remove from the print order.
Press the selector up or down to
2
choose the number of copies (up
to 99). To remove a picture from the
order, press the selector down until
the number of copies is 0.
Total number of prints
Number of copies
88
Printing Pictures via USB
R Print orders can contain a maximum of 999 pictures.
R If a memory card is inserted
■ RESET ALL
To cancel the current print
order, select RESET ALL for
KPRINT ORDER (DPOF). The
confirmation shown at right
will be displayed; press MENU/OK
to remove all pictures from the
order.
containing a print order cre-
ated by another camera, the
message shown at right will
be displayed. Pressing MENU/OK
cancels the print order; a new
print order must be created as
described above.
89
Viewingg Picturreess oonn aa CCoommppuutter
The supplied software can be used to copy pictures to a computer, where they can be stored, viewed,
organized, and printed. Before proceeding, install the software as described below. Do NOT connect
the camera to the computer until installation is complete.
Windows: Installing MyFinePix Studio
Confirm that the computer meets the following system requirements:
1
Windoows 7 (Service Pack 1))/Winndows Vista (Service Paack 2)1
Windows XP (Service Pack 3)1
3GHz Pentium 4 or better
2GHz Pentium 4 or better
CPU
(2.4GHz Core 2 Duo or better2)
(2.4GHz Core 2 Duo or better2)
RAM
1GB or more
512MB or more (1GB or more2)
Free disk space
2GB or more
Supports DirectX 7 or later (required; performance
not guaranteed with other GPUs)
GPU
Supports DirectX 9 or later (recommended)
Video
1024×768 pixels or more with 24-bit color or better
• Built-in USB port recommended. Operation is not guaranteed with other USB ports.
• .NET Framework 3.5 Service Pack 1 required when uploading images or using Map Viewer.
• Internet connection (broadband recommended) required to install .NET Framework (if necessary), to use
auto update feature, and when performing such tasks as sharing pictures on-line or via e-mail.
Other
1 Other versions of Windows are not supported. Only pre-installed operating systems are supported; operation is not
guaranteed on home-built computers or computers that have been upgraded from earlier versions of Windows.
2 Recommended when displaying HD movies.
Start the computer. Log in to an account with administrator privileges before proceeding.
2
90
Viewing Pictures on a Computer
Exit any applications that may be running and insert the installer CD in a CD-ROM drive.
3
Windoows 7/Wiindows Vista
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed;
click Yes (Windows 7) or Allow (Windows Vista).
The installer will start automatically; click Install MyFinePix Studio and follow the on-screen in-
structions to install MyFinePix Studio and RAW FILE CONVERTER.
If the Installer Does Noott SSttaarrtt AAuuttoommaattiiccaalllly
If the installer does not start automatically, select Computer or My Computer from the Start menu, then
double-click the FINEPIX CD icon to open the FINEPIX CD window and double-click setup or SETUP.EXE.
If prompted to install Windows Media Player or DirectX, follow the on-screen instructions to com-
plete installation.
4
5
Remove the installer CD from the CD-ROM drive when installation is complete. Store the installer
CD in a dry location out of direct sunlight in case you need to re-install the software.
Installation is now complete. Proceed to“Connecting the Camera”(P94).
91
Viewing Pictures on a Computer
Macintosh: Installing FinePixViewer
Confirm that the computer meets the following system requirements:
1
CPU
PowerPC or Intel (Core 2 Duo or better)
Pre-installed copies of Mac OS X version 10.3.9–10.6 (visit http://www.fujifilm.com/support/digital_cameras/
compatibility/ for more information). Mac OS X version 10.7 and later not supported.
OS
RAM
256MB or more (1GB or more recommended when displaying HD movies)
Free disk space A minimum of 200MB required for installation with 400MB available when FinePixViewer is running
Video
Other
800×600 pixels or more with thousands of colors or better
Built-in USB port recommended. Operation is not guaranteed with other USB ports.
After starting the computer and quitting any applications that may be running, insert the installer
CD in a CD-ROM drive and double-click Installer for Mac OS X.
2
3
An installer dialog will be displayed; click Installing FinePixViewer to start installation. Enter an
administrator name and password when prompted and click OK, then follow the on-screen in-
structions to install FinePixViewer. Click Exit to quit the installer when installation is complete.
R To install RAW FILE CONVERTER, double-click SILKYRFCEXInstaller. RAW FILE CONVERTER is used to view
RAW images on your computer.
Remove the installer CD from the CD-ROM drive. Note that you may be unable to remove the CD
if Safari is running; if necessary, quit Safari before removing the CD. Store the installer CD in a dry
location out of direct sunlight in case you need to re-install the software.
4
92
Viewing Pictures on a Computer
Mac OS X 10.5 or earlier: Open the“Applications”folder, start Image Capture, and select Preferences…
from the Image Capture application menu. The Image Capture preferences dialog will be displayed;
choose Other… in the When a camera is connected, open menu, then select FPVBridge in the
“Applications/FinePixViewer”folder and click Open. Quit Image Capture.
5
Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications” folder and start Image
Capture. The camera will be listed under DEVICES; select the camera and choose FPVBridge from
the Connecting this camera opens menu and click Choose. Quit Image Capture.
Installation is now complete. Proceed to“Connecting the Camera”(P94).
93
Viewing Pictures on a Computer
Connecting the Camera
Find a memory card containing pictures you want to copy to the computer and insert the card into
the camera (P14).
1
R Windows users may require the Windows CD when starting the software for the first time.
Q Loss of power during transfer could result in loss of data or damage to the memory card. Insert a fresh or
fully-charged battery before connecting the camera.
Turn the camera off and connect the supplied USB cable as
2
shown, making sure the connectors are fully inserted. Con-
nect the camera directly to the computer; do not use a USB
hub or keyboard.
Turn the camera on. MyFinePix Studio or FinePixViewer will start automatically; follow the on-screen
instructions to copy pictures to the computer. To exit without copying pictures, click Cancel.
3
Q If the software does not start automatically, it may not be correctly installed. Disconnect the camera and
reinstall the software.
For more information on using the supplied software, start the application and select the appropriate
option from the Help menu.
94
Viewing Pictures on a Computer
Q If a memory card containing a large number of images is inserted, there may be a delay before the software
starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.
Q Make sure that the computer does not display a message stating that copying is in progress and that the indi-
cator lamp is out before turning the camera off or disconnecting the USB cable (if the number of images cop-
ied is very large, the indicator lamp may remain lit after the message has cleared from the computer display).
Failure to observe this precaution could result in loss of data or damage to the memory card.
Q Disconnect the camera before inserting or removing memory cards.
Q In some cases, it may not be possible to access pictures saved to a network server using the supplied software
in the same way as on a standalone computer.
Q The user bears all applicable fees charged by the phone company or Internet service provider when using
services that require an Internet connection.
Disconnecting thhee CCamera
After confirming that the indicator lamp is out, turn the camera off and disconnect the USB cable.
Uninstalling the Supplied Softtwwaarree
Only uninstall the supplied software when it is no longer required or before beginning reinstallation. After
quitting the software and disconnecting the camera, drag the“FinePixViewer”folder from“Applications”into the
Trash and select Empty Trash in the Finder menu (Macintosh), or open the control panel and use “Programs
and Features” (Windows 7/Windows Vista) or “Add or Remove Programs” (Windows XP) to uninstall MyFinePix
Studio. Under Windows, one or more confirmation dialogs may be displayed; read the contents carefully before
clicking OK.
95
Technical Notes
Oppttiioonnaall AAcccesssoories
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.
Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest information on the accesso-
ries available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.com/
products/digital_cameras/index.html.
Recharggeeaabbllee LLii--iioonn bbaatteries
NP-W126: Additional large-capacity NP-W126 rechargeable batteries can be purchased as required.
Batteryy chargers
BC-W126: Replacement battery chargers can be purchased as required. At+20°C/+68°F, the BC-W126
charges an NP-W126 in about 150 minutes.
FUJINOON Lenses
XF18mmF2 R: F=18mm, maximum aperture f/2.
XF35mmF1.4 R: F=35mm, maximum aperture f/1.4.
XF60mmF2.4 R Macro: F=60mm, maximum aperture f/2.4.
96
Optional Accessories
Prootector Filter
PRF-52: Protector Filter (diameter 52mm).
PRF-39: Protector Filter (diameter 39mm).
Grips
HG-XPro1: Features an improved grip.
Shoe-mounted flash units
EF-20: This clip-on flash unit (powered by two AA batteries) has a Guide Number of 20/66 (ISO 100, m/ft.)
and supports TTL flash control. The flash head can be rotated upwards 90° for bounce lighting.
EF-42: This clip-on flash unit (powered by four AA batteries) has a Guide Number of 42/138 (ISO 100, m/ft.)
and supports TTL flash control and auto power zoom in the range 24–105 mm (35 mm format equivalent).
The flash head can be rotated 90° up, 180° left, or 120° right for bounce lighting.
EF-X20: This clip-on flash unit has a Guide Number of 20/66 (ISO 100, m/ft.).
Leeaatther cases
LC-XPro1: This leather case, exclusively for use with the X-Pro1, combines practicality with the luxury of leather and comes with
a shoulder strap made of the same material. Pictures can be taken with the camera still in its case.
97
Optional Accessories
Recommended Third-Party Accessories
Diopter adjustment lenses
COSINA diopter adjustment lenses are recommended for use with this camera.
98
Optional Accessories
Connecting the Camera to Other Devices
■ Printing
■ Fllash Photography
X-Pro1
USB cable
(supplied)
EF-20 shoe mount EF-42 shoe mount
EF-X20 shoe
mount flash *
flash *
flash *
PictBridge-compatible printer†
SD/SDHC/SDXC
memory card†
■ Leens
Printer†
XF18mmF2 R * XF35mmF1.4 R * XF60mmF2.4 R Macro *
■ Coommpputer Reellatteedd
USB cable (supplied)
■ Audio/Visual
SD card slot or card reader
HDMI cable†
Computer†
HDTV†
* Available separately from FUJIFILM.
† Available separately from third-party suppliers.
99
Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
Storage and Use
■ Water and Sand
If the camera will not be used for an extended pe- Exposure to water and sand can also damage the
riod, remove the battery and memory card. Do camera and its internal circuitry and mechanisms.
not store or use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
• exposed to direct sunlight or very high temper-
atures, such as in a closed vehicle on a sunny
day
When using the camera at the beach or seaside,
avoid exposing the camera to water or sand. Do
not place the camera on a wet surface.
■ Condensation
Sudden increases in temperature, such as occur
when entering a heated building on a cold day,
can cause condensation inside the camera. If this
occurs, turn the camera off and wait an hour be-
fore turning it on again. If condensation forms on
the memory card, remove the card and wait for
the condensation to dissipate.
• extremely cold
• subject to strong vibration
• exposed to strong magnetic fields, such as near
a broadcasting antenna, power line, radar emit-
ter, motor, transformer, or magnet
• in contact with volatile chemicals such as pes-
ticides
Traveling
• next to rubber or vinyl products
Keep the camera in your carry-on baggage.
Checked baggage may suffer violent shocks that
could damage the camera.
100
Clleeaanniinngg tthhee IImage Seensor
Multiple photographs marred by spots or blotches in identical locations may indicate the presence
of dust on the camera image sensor. Clean the sensor using the VSENSOR CLEANING option in
the setup menu (P82); if the problem persists, you can clean the sensor manually as described below.
Note that there will be a charge to repair or replace the image sensor if it is damaged during cleaning.
Use a blower (not a brush) to remove dust from the sensor.
1
Q Do not use a brush or blower brush. Failure to observe this precaution could damage the sensor.
Check whether the dust has been successfully removed.
2
R Repeat Steps 1 and 2 as necessary.
Replace the body cap or lens.
3
101
Troubleshooting
Problems and Solutions
Power and Battery
Problem
Solution
• Thhee bbaattery is exhausted: Chharge the batttery (P12) or innsert a fullly-charrgged spare bbattery (P13).
• Thhee bbaattery is inserted iincorrectly: Reeiinnsseerrtt iinn tthhee ccorrreecct oriieennttation (P13).
• Thhee bbaatttteerry-chamber cover is not latched: Lattcchh tthhe batttteery-chamber ccovveerr (P14).
The cameera does not
turn on.
• Thhee bbattery is cold: Warmm tthhee bbaatterry by placing it in a pocket or otheer waarrm plaace and reinsert it in the cameraa
immediiatteely before taking a picture.
The battery runs down
quickly.
• Thheerree iiss ddiirrtt oonn tthhee bbaatttteerryy tteerminals: CClleeaann tthhee terminalss with a sooft, dry cloth.
• C is selected for focus mode: Seelleecctt aa diiffereennt focus mode (P45).
• Thhee battery has been charggeedd mmaanny ttiimes: The batttteerryy has reached the end of its charging life. Purchase a neww
battery.
The cameera turns off
suddenly.
Thhee bbaattery is exhausted: Chharge the batttery (P12) or innsert a fuully-chaarrged sparee battery (P13).
Charging does not start. Reeiinnsseerrtt tthhee bbaattery in the correct oriieenntation and make sure thatt tthhee cchhaarrggeerr iiss pplluuggggeedd iinn ((P12).
Charging is slow.
Chharge the baattery att room temperattuurree ((Piv).
The charging lamp liigghhts, • Thheerree iiss ddiirrtt oonn tthhee bbaatttteerryy tteerminals: Clleeaann tthhee terminals with a soft, dry cloth.
but the battery does not • Thhee battery has been charggeedd mmaanny ttiimes: The batttteerryy has reached the end of its charging life. Purchase a neww
charge.
batttteery. If the batttteerryy ssttiillll fails to charge, coonnttaacctt yyoouurr FFUUJJIIFFIILLMM ddeeaalleerr..
Menus and Displays
Problem
Solution
Display is not in English. Seellect ENGLISH for La (P80).
102
Problems and Solutions
Shooting
Problem
Solution
• Memory is full: Insert a new memoory carrdd or deleete piccturess (P14, 65).
• Memory is not formatted: Formmaat the memory card (P83).
• Thheeree iiss ddiirrtt oonn tthhee mmemory cardd ccoonnttacts: Cllean the coonnttaaccttss wwiitthh aa ssoofftt,, ddrryy ccllootthh..
• Thhee memory cardd iiss ddaamaged: Insert a new mmemorry card (P14).
• Thhee bbaattery is exhausted: Chharge the batttery (P12) or innsert a fullly-charrgged spare bbattery (P13).
• Thhee ccaamera has turned off automatically: Turnn tthhee ccaammeerra oon (P17).
• Thhee indicator lamp wwas oraange wwhhen yyoouu aatttteemmpptteedd ttoo rreeccoorrd a paanoramma: Waitt uunttiill tthhee iinnddiicattoorr llaammppss ttuurrns off
(P3).
Noo ppiiccture is taken when
the shutter button is
pressed.
Mottling (“noise”) appears
in the monitor or
electroniic viewfinder
when the shutter button is
pressed halfway.
Gain is increased to aid coommppoossiittiioonn wwhheenn tthhee ssuubbjjeecctt iiss ppoooorrly lit and aperture is ssttooppppeedd dowwnn,, wwhhiicchh mmaayy rreessuulltt
in noticeeaabbllee mmoottttlliinngg wwhheenn iimmaaggeess aarree pprreeviewweedd iinn tthhee ddiissppllaayyss.. IImmaaggeess ttaakkeenn wwiitthh tthhee ccaammeerra are unaffected.
• Thhee ssuubbjjeecct is close to the camera: Seelleecctt macrro modee (P31).
The cameera does not ffocus. • Thhee ssuubject is far away froomm tthhe camera: Cancel macro mode (P31).
• Thhee ssuubbjjeecct is not suited to autofocus: Usse focus lock (P43) or manual focus (P45).
• Thhee flflaasshh ccaann not be used at curreenntt sseettings: Seeee tthhee lliisstt ooff tthhee sseettttiinnggss tthhaatt can bbee used wwith tthhe flashh (P54).
• Thhee flaasshh is off (P): Chhoose a different flash mode (P54).
The flash does not fire.
• Thhee bbaattery is exhausted: Chharge the batttery (P12) or innsert a fullly-charrgged spare bbattery (P13).
• Thhee ccaammeerraa is in continuous mode: Seelleectt aa differentt ddrrive mode (P34).
• Thhee ccaammeerraa is in silent mode: Turnn ssiilleennt mode off (P30, 80).
Some flash modes are not
available.
The camera is in silentt mmooddee.. TTurn silennt mode off (P30, 80).
103
Problems and Solutions
Problem
Solution
• Thhee ssuubbjjeecct is not in range of the flash: Posiition thhe subjeect in range of the flash.
• Thhee flflaasshh wwiinndow is obstructed: Hold the cameraa ccoorrrreeccttllyy..
The flash does not fully
light the subject.
/
• Shutter speed is faster than 1180s: Chhoose a slowweerr sshhuutttteer speed (P25, 27).
• Thhee lleennss iiss ddiirrtty: Clleeaan the lens (Pxi).
• Thhee lleens is blocked: Keep objects away from the lens.
• sis diisplayyed duurring sshhootinng andd tthe fooccuuss ffrraammee iiss ddiissppllaayyeedd iinn rred: Chheecckk ffooccus before shooting (P30).
• kis displayed during shooting: Ussee tthe flaassh or mountt tthhee ccaammeerraa oonn aa ttrripod (P54).
• Shuttter sppeeed is sslow annd the aambiennt teemmppeerraattuurre is hhigh: This is normmaall aanndd ddooeess nnoott iinnddiiccaate a malfunction.
• Thhee ccaammeerraa hhaass bbeeeenn uusseedd ccoonnttinuously att high ttemperratures or a temperaturee wwaarrnniinngg iiss ddiissppllaayyeedd: Turn thhe cam-
era off and waait for it to cool dowwnn..
Piiccttuures are blurred.
Piiccttuures are mottled.
Playback
Problem
Solution
Piicctures are grainy.
The pictures were taken with a differeent make or modell of camera.
Playback zoom is unavail-
able.
The picttures weerre crreeaatedd using ORESIZE or with a different make or model off camera.
• Playback volume is too low: Adjust playback volume (P78).
Noo ssoouund in movie
playback.
• Thhee microopphhoonnee wwaass oobstructed: Hold the cameraa ccoorrrreeccttllyy dduurring recoorrddiinngg ((P2, 39).
• Thhee ssppeaker is obstructed: Hold the cameraa ccoorrrreeccttllyy dduurring playybbaacckk ((P2, 59).
• Thhee ccaammeerraa is in silent mode: Turnn ssiilleennt mode off (P30, 80).
Selected pictures are not Soommee ooff tthhee ppiiccttuurreess sseelleecctteedd ffoorr ddeelleettiioonn aarree pprrootteecctteedd.. RReemmoovvee pprrootteeccttiioonn uussiinngg tthhee ddeevviiccee wwiitthh wwhhiicchh iitt wwas
deleted.
oriiggiinnally aappliieed (P75).
File numbering is unex-
pectedly reset.
The baattery-chhambeerr covveerr wwaass ooppeenneedd wwhhiille the cameraa wwaass on. TTurrnn tthhee ccaammeerraa ooffff bbeeffoorree ooppeenniinngg tthhee bbaatt--
tery-chammber ccovveerr (P13, 17).
104
Problems and Solutions
Connections/Miscellaneous
Problem
Solution
• Thhee ccaamera is not prooppeerrlly connected: Connect the cameraa pprrooppeerrly (P84). Note thaat oncee tthhe cameraa iiss ccoonn--
nected, piictures wiill be dispplayed onn tthhee TTVV iinnsstteeaadd ooff iinn tthhee ccaammeerraa moniitor.
• Input on the television is set to “TV”: Seett iinnppuutt ttoo““HHDDMMII”.
Noo ppiiccture or sound.
• Thhee vvoolume on the TV is too llow: Ussee tthe coonnttrroollss oonn tthhee tteelleevvision to adjust the vvolume.
The coomputer does not
recognize thee camera.
Bee ssuurree tthhee ccaammeerra aand computer are coorrrecttly connected (P94).
Can not traannssffeerr RRAW or
JPEG filess to computer.
Ussee tthhe bundled software tto transfer pictures (P90).
Piiccttuures can not be
printed.
• Thhee ccaamera is not prooppeerrlly connecteed: Connect the cameraa ccoorrrreeccttllyy ((P85).
• Thhee pprrinter is off: Turnn tthe priinnter on.
Only one copy is prrinted/
the daate iss nnot printed.
The priinnteer is not PiictBriiddggee ccompatible.
The camera is unrespon- • Temporary camera malfunction: Reemmoove and reinsert the battery (P13, 15).
sive.
• Thhee bbaattery is exhausted: Chharge the batttery (P12) or innsert a fullly-charrgged spare bbattery (P13).
Reemmoovve andd rreinsert thhe battery (P13,, 15). If the pprobllem perrsisttss, conttaacctt yyoouurr FFUUJJIIFFIILLMM ddeealer.
Turnn ssiilleennt mode off (P30, 80).
The camerra does not func-
tion as expected.
Noo sound.
105
Warning Meessages and DDissplays
The following warnings appear in the display.
Warning
Description
B(red)
A(blinks red)
k
Low battery. Chharge the batttery (P12)) or inserrt a fullyy-chargeed spare bbattery (P13).
Baattery exxhausted.. CCharge thee battery (P12) oor insert aa fullly-chhaarged sparre battery (P13).
Slow shutter speed. Pictures may be bluurrred; uuse the flash or a triipod.
s
(displayed in red with
red focus frame)
The caamera can not focus. TTry onee of thee folloowing solutions:
• Ussee ffoocus lock to focus on aanother ssubject aat the same disstance, then recoommppoosse the picture (P43).
• Ussee mmaaccrroo mmode to focus when taking close-ups (P31).
Aperture or shutter speed The subject is too brriigghhtt oorr ttoooo ddaarrkk aanndd tthhee ppiiccttuurree wwiillll bbee oovveerr-- oorr uunnddeerr-exposseedd.. IIff tthhee ssuubbjjeecctt iiss ddaarrkk,, uussee tthhee
displayed in red
flash (P54).
FOCUS ERROR
TURN OFF THE CAMERA
AND TURN ON AGAIN
Camerraa mmaallfunction. Turn the ccamera off and then on agaiin. If tthe meessagee perssiists,, cconttaacctt aa FFUUJJIIFFIILLMM ddeeaaller.
LENS CONTROL ERROR
LENS ERROR
BUSY
Turnn tthhee ccaammeerra off, remmovvee tthe lens, and clean the mounnting surfaceess,, tthhen replacee tthhee lleennss aannd turn the camerra
on. If tthe prooblem ppeerrssiissttss,, ccoontact a FUJIFILM deaaler.
The memorry card iss incorrecctly forrmmaattteedd.. UUse the cameeraa tto formaat the card (P83).
• Thhee mmeemmoorryy ccaarrdd iiss nnoott ffoorrmmaatttteedd oorr tthhee mmeemmoorryy ccaarrdd hhaass bbeeeenn ffoorrmmaatttteedd iinn aa ccoommppuutteerr oorr ootthheerr ddeevviiccee: Formmaat the
memory card using the KFORMAT optionn in thhe cammeera setup menu (P83).
• Thhee memory carrd contacts requiree cclleeaning: Clean the conttaaccttss wwiith a soft,, ddry cloth. IIf thee mmeessssaaggee iiss rreeppeeaatteedd,,
formmaat the card (P83)). If thhe messaage perrsists,, replaace the card.
• Caammeerra mallfunctionn: Conttact a FUJIFILM dealer.
The memory card is locked. Unlock the card (P14).
CARD NOT INITIALIZED
PROTECTED CARD
106
Warning Messages and Display
Warning
Description
• Thhee mmeemory cardd iiss nnoott ffoorrmmaatttted for use in the camera: Formmaat the card (P83).
• Thhee memory cardd ccoonnttacts reeqquuiirree cclleeaanniinngg oorr tthhee mmeemory cardd iiss ddaammaaged: Clean the coonttaaccttss wwiith a soft,, ddrryy
cloth. If tthe meessagee is reepeated, formmaat the card ((P83).. If thhee messaage peersistts, reeplace the card.
• Incommpatiibbllee mmeemmoorryy ccaarrdd: Use a coommppaattiibbllee ccaarrd (P16).
CARD ERROR
• Caammeerra mallfunctionn: Conttact a FUJIFILM dealer.
The memmory caarrd is fuull aanndd ppiiccttuurreess ccaann nnoott bbee rreeccorrddeedd.. DDeelleettee ppiiccttuurreess ((P65) oor inseert a meemmory caard with
more freee spacce (P14).
bMEMORY FULL
The shutter can only be released when a memory card is inserted. Insert a memory card.
NO CARD
• Memorry carrd error or connectiion errrror: Reeiinnsseerrtt tthhee ccaarrdd oorr ttuurnn tthhee ccaammeerraa off andd then oon agaiin. Iff tthe message
persistts, conttaacctt aa FFUUJJIIFFIILLMM dealer.
• Noott eennoough memory reemmaining to reeccoordd aaddddiittiioonnaal pictureess: Dellete pictuurres (P65) or insert a memory card
with mmore frree sppaace (P14).
• Thhee memory cardd iiss nnoot formatted: Formmaat the memory card (P83).
• Thhee fifillee iiss ccoorrupt or was not creeaatteedd with the camera: The file can not be viieewed.
• Thhee memory carrd contacts requiree cclleeaning: Clean the conttaaccttss wwiith a soft,, ddry cloth. IIf thee mmeessssaaggee iiss rreeppeeaatteedd,,
formmaat the card (P83)). If thhe messaage perrsists,, replaace the card.
WRITE ERROR
READ ERROR
• Caammeerra mallfunctionn: Conttact a FUJIFILM dealer.
The cameeraa hhaass rruunn oouutt ooff ffrraammee nnuummbbeerrss ((ccuurrrreenntt ffrraammee nnuummbbeerr iiss 999999--99999999)).. FFoorrmmaatt tthhee mmeemmoorryy ccaarrdd aanndd
select RENEW for BFRAME NO. Take a picture to reset fraammee nnuummbbeerring to 100-0001, then select CONTINU-
OUS for BFRAAME NO. (P81).
FRAAME NO. FULL
• A search has reetturned moree tthan 30,000 results: Chhoooossee aa ssearch thatt rreettuurrns fewer results.
• Moree tthan 999 images aree sseelleeccted for deletion: Chhoooose fewer images.
TOO MANY FRAMES
107
Warning Messages and Display
Warning
Description
An atttteemmpptt waass mmaaddee ttoo ddeelleettee oorr rroottaattee ttoo aa pprrootteecctteedd ppiiccttuurree.. RRemovvee pprrootteeccttiioonn aanndd ttrryy aaggaaiinn ((P75).
The piccture iis damaaggeedd oorr wwas nott created with the ccamera.
Reedd--eeyyee rreemmoovval caan not be appllied to piicctures crreatteedd wwiitthh ootthheerr ddeeviceess..
Reedd--eeyyee rreemmoovval can noot be applied tto movviieess..
PROTECTED FRAAME
CAN NOT CROP
mCANNOT EXECUTE
FCANNOT EXECUTE
CAN NOT ROTATE
The selectted picturre can not bbe rotated.
Mooviess can noot be roottaated.
FCAN NOT ROTATE
The DPOOF priinnt oorrddeerr oonn tthhee ccuurrrreenntt mmeemmoorryy ccaarrdd ccoonntaaiinnss mmoorree tthhaann 999999 iimmaaggeess.. CCooppyy tthhee ppiiccttuurreess ttoo aa ccoomm--
puter and creattee aa nneew priinnt order.
DPOF FILE ERROR
The picture can not be priinnted using DPOF.
Moovies can not be priinnted using DPOF.
CAN NOT SET DPOF
FCAN NOT SET DPOF
A coonnnneeccttiioonn eerrror occcuurrred while pictures were being priinted or cooppiieedd ttoo aa ccoommppuutteerr oorr ootthheerr ddeevviiccee.. CCoonnfifirrmm
thatt tthhee ddeeviice is turnned on aannd that the USB cable is coonnnneeccted.
Printteerr out oof paper or ink, or other printer errroorr.. CCheck priinnter (see priinnter manual for details). To resume printing,
turnn tthe priinnter off annd then turn itt back on.
COMMUNICATION ERROR
PRINTER ERROR
Printteerr oout of paper or ink, or other priinntter errroorr.. CCheeck priinnter (ssee priinnter maanual foor detaails).. If priinnting ddoes not
resume aautomatically, press MENU/OK to resume.
PRINTER ERROR
RESUME?
An attttempt waass mmaaddee ttoo pprrintt aa mmovviiee,, aa ppiiccttuurree nnoott ccrreeaatteedd wwiitthh tthhee ccaammeerraa,, oorr aa ppiiccttuurree iinn aa ffoorrmatt nnoott ssuupp--
ported byy tthhee pprrintteerr.. MMovviieess,, RRAAWW iimmaaggeess,, aanndd ssoommee pictures creatteedd wwiitthh ootthheerr ddeevvices can not be priinted; if
the pictture iss a stilll pictuure creeated with the cameraa,, cchheecckk tthhee pprriinntteerr mmaannuuaall ttoo ccoonnfifirrmm tthhaatt tthhee pprriinntteerr ssuuppppoorrttss
the JFIF--JPEG or Exxif-JPEGG fformmaat. If it does not,, tthhee ppiiccttuurreess ccaann nnoott bbee pprrintteedd..
CANNOT BE PRINTED
p
Turnn tthhee ccaammeerra off annd waaiitt ffoorr iitt to cooooll.. MMottling may increase in pictures taken when this waarrning is displayed.
108
Appendix
Gllossary
DPOF (Digital Print Order Format): A standard that allows pictures to be printed from “print orders”stored
on a memory card. The information in the order includes the pictures to be printed and the number of
copies of each picture.
EV (Exposure Value): The exposure value is determined by the sensitivity of the image sensor and the amount
of light that enters the camera while the image sensor is exposed. Each time the amount of light doubles, EV
increases by one; each time the amount of light is halved, EV decreases by one. The amount of light entering the
camera can be controlled by adjusting aperture and shutter speed.
Exif Print: A standard for storing information with pictures for optimal color reproduction during printing.
HDMI (High-Definition Multimedia Interface): An interface standard for the transmission of images and sound that
adds audio input to the DVI interface used to connect computers to displays.
JPEG (Joint Photographic Experts Group): A compressed file format for color images. The higher the compression
rate, the greater the loss of information and more noticeable drop in quality when the picture is displayed.
MOV: A movie file format (extension “.mov”) developed by Apple, Inc., and viewed using QuickTime Player. This
format is popular on the Internet.
White balance: The human brain automatically adapts to changes in the color of light, with the result that objects
that appear white under one light source still appear white when the color of the light source changes. Digital
cameras can mimic this adjustment by processing images according to the color of the light source. This process
is known as“white balance.”
109
Meemory Carrd Caappacityy
The following table shows the recording time or number of pictures available at different image sizes.
All figures are approximate; file size varies with the scene recorded, producing wide variations in the
number of files that can be stored. The number of exposures or length remaining may not diminish
at an even rate.
Capacity
4 GB
8 GB
O
TFINE
620
730
930
990
1160
1470
1850
2170
2750
480
TNORMAL
990
TFINE
1250
1480
1870
1990
2340
2960
3710
4360
5530
970
TNORMAL
1990
2340
2920
3880
4600
5650
7110
8290
8020
1910
2820
2820
4210
O3 : 2
O16 : 9
O1 : 1
P3 : 2
P16 : 9
P1 : 1
Q3 : 2
Q16 : 9
Q1 : 1
O(verttical)
O(horizontal)
P(verttical)
P(horizontal)
RAW
1160
1450
1930
2290
2810
3540
4130
3990
950
720
720
1060
1400
1400
2100
1440
1440
2140
160
320
h1280
38min.
54min.
76min.
109min.
i1920
* Use a Gcard or better. Individual movies can not exceed 29 minutes in length.
110
Specificcaattions
System
Model
X-Pro1 digiital ccamerra
16.3 million
Effective pixels
Image sensor
23.6 mm × 155.6 mmm (APSS--CC formmaatt)) CCMMOOSS ((coommpplleemmeennttary meetal-ooxidee semiconductor) image sensor with
square pixels and priimmaarryy ccolor filter
Storage media
File system
FUJIFILM--rreeccommmenddeed SD//SSDHC/SSDXC mmeemory ccards
Compliaant with Design Rule for Cameera File System (DCF), Exif 2.3, and Digital Print Order Formmaat (DPOF)
File format
• Still ppicturres: Exif 2.3 JPEG (compressed); RAAW (origiinnaall RRAAFF ffoorrmmaatt,, ssppeecciiaall--ppuurrppoossee ssooffttwware required); RAWW++JPG avvailable
• Movies: H.264 standard with stereo sound (MOV)
Image size
• O3 : 2: 4,896 × 3,624
• O16 : 9: 4,896 × 2,760
• O1 : 1: 3,264 × 3,264
• P3 : 2: 3,4556 × 2,304
• P16 : 9: 3,4456 × 1,944
• P1 : 1: 2,3004 × 2,304
• Q3 : 2: 2,496 × 1,664
• Q16 : 9: 2,496 × 1,408
• Q1 : 1: 1,664 × 1,664
• O panorama: 2,160 × 7,680 (vertiical) / 7,680 × 1,440 (horizontal)
• P panorama: 2,160 × 5,120 (vertiical) / 5,120 × 1,440 (horizontal)
Lens mounnt
Sensitivity
FUJIFILLM X mouunnt
/
Sttaannddaarrdd oouuttpput sensitivity equivaalleenntt ttoo IISSOO 220000––66440000 iinn iinnccrreemmeennttss ooff EV; AUTO (400), AUTO (800), AUTO
(1600), AAUTO (32000); extenndded outpuutt sseennssiittiivviittyy eeqquuiivvalent ISO 100, 12800, or 25600
Metering
256-seegment through-the-lens (TTL) meteerriing; MULTI, SPPOOTT,, AAVVEERRAGE
Exposurree ccontrol
Programmed AE (with progrraamm sshhiifft); shutter--pprriioorriity AE; aperture-prioriittyy AAEE;; manual eexposure
/
Exposure compensation –2 EV – +2 EV in incremmeennts of EV
/
/
Shhuutttter speed (combined • P mode: sec. to sec.
mechanicaall and electronic
shutter)
• Time: 30 sec. to 2 sec.
• All other modes: 30 sec. to sec.
/
• Bulb: Maaxx.. 60 min.
111
Specifications
System
Continuous
Focus
Approximmately 6 or 3 fps
• Mode: Sinngle orr cconttiinnuuoouuss AAFF;; mmaannuuaall ffooccuuss wwiitthh ffooccuuss rring
• Focus--area selection: Multti, areeaa with foocus arreea size sselecttion; 449 (7 × 7)) areass aavailabble in ellectronnic vieewwfifinnddeerr
and LCD monitor, 25 (5 × 5) areas availabbllee iinn ooppttiiccaall vviieewfinder
• Autofoccus systemm: Contraasstt--ddeetteecctt TTTTLL AAFF wwiitthh AAFF--aassssiisst illuminattoorr
Whhite balance
Customm, color temperrattuurree sseellection, auto, ddirectt sunnlliigghht,, sshade, daylight fluuoresceenntt,, wwaarrmm wwhhiittee flfluuoorreesscceenntt,,
cool whiite fluoorreesscceennt, incandeessccent,, uunderrwatteerr
Self-timer
Flash
Off, 2 sec., 10 sec.
/
Accceessssoorryy sshhooee with TTL coonnttaaccttss aanndd ssyync coonnttaacctt ((XX ccoonnttaacctt)) tthhaatt ssuuppppoorrttss ssyynncc ssppeeeeddss aass ffaasstt aass s
Mode
Auto, fill flash, off,, rear--ccuurrttaaiinn ssyynncc,, ssloww ssyynncc (red--eye reemmooval ooff); auto with red-eeyye removvaall,, fifillll flflaasshh wwiitthh rreedd--eeyyee
removaall,, ooff, rear--ccuurrttaaiinn ssyynncc wwiitthh rreedd--eeyyee rreemmoovaall, sloww ssyynncc wwiitthh rreedd--eye reemovaall (red-eeye remmooval on)
Hybrid vviewfinder
• Optical viiewfinder: Reevveerrssee GGaalliilleeaann vviieewwfifinnddeerr wwiitthh eelleeccttrroonniicc bbrriigghhtt ffrraammee ddiissppllaayy aanndd aapppprrooxx.. 00..3377××//00..66×× mmaagg--
nification;; frame coovveerraaggee aapppprrooxx.. 9900%%
• Electroonniicc viewfinder: 0.477-in.,, 1,4400kk--ddoott ccolorr LCD vieewwfifinnddeerr;; eeyyee ppooiinntt aapppprrooxx.. 1144mmmm;; ffrraammee ccooveerage approx.
100%
LCD monitor
Movies
3.0-inn./7.6 ccm, 1,223300kk--ddoott RRGGBBWW ((rreedd,, ggrreeeenn,, bblluuee,, aanndd wwhhiittee)) ccoolloorr LLCCDD mmoonniittoorr;; ffrraammee ccoovveerragee approoxx. 100%
i (1,920 × 1,080)/h (1,280 × 720); 24 fps; stereo sound; maximum length 29 minutes
Input/output terminals
HDMI output
HDMI minni connector
USB 2.0 High-Speed
Digital input/output
112
Specifications
Power supply/other
Power supply
NP-W1266 recharrggeabbllee bbaattery
Battery liife (approximate
numberr of fraames thhaatt ccan
be takeen withh a fullly-charged
battery)
Battery type
NP-W126 (tyype suppplied wiithh ccamera)
CIPA staandard,, mmeasuredd using bbattery supplied with ccamera and SD memory card.
Notte: NNumberr of shhoots thhaat can be ttakenn wwith baattery vaarries wwith baattery charge levveell aanndd wwiillll ddeecclliinnee aatt lloow
temperrattuures.
Approoximate number of frames
300
Camera size (W × H × D) 139.5 mm × 81.8 mm × 42.5 mm (34.1 mm excluding projections, measured at thinnest part)/5.5 in. × 3.2 in. × 1.7 in. (1.3 in.)
Camera wweight
Approx.. 400 g/114.1 oz.., excludding battery, accceessssoorriieess,, and memory card
Approxx. 450 gg//15.9 ozz., inccludinng battery and memorry card
Shhoooottiinngg wweeiigghht
Operatingg conditions
• Temperratuurree: 0 °C to +40 °C/+32 °F to +104 °F
• Humidity: 10% – 80% (no condensation)
113
Specifications
NP-W126 rechargeable battery
Noomminal voltage
7.2V DC
Noomminal capacity
1,260 mAh
Operating teemperrature
0 °C to +40 °C/+32 °F to +104 °F
Dimensions (W × H × D) 36.4 mm × 47.1 mm × 15.7 mm/1.4 in. × 1.9 in. × 0.6 in.
Weight
Approx. 47 g/1.7 oz.
BC-W126 battery charger
Raatteedd input
100V – 240V AC, 50/60 Hz
13 –21VA
Input capacity
Raatteedd ooutput
8.4V DC, 0.6 A
Supported batteries
Charging time
NP-W126 rechargeable batttteerries
Approx. 150 minutes (+20 °C/+68 °F)
5 °C to +40 °C/+41 °F to +104 °F
Operating teemperrature
Dimensions (W × H × D) 65 mm × 91.5 mm × 28 mm/2.5 in. × 3.6 in. × 1.1 in., excluding projections
Weight Approx. 77 g/2.7 oz., excluding battery
Weight and dimensions vary with the country or region of sale. Labels, menus, and other displays may differ from those on the
actual camera.
114
Specifications
■ Noottiices
• Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/
digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual.
• Although the electronic viewfinder and LCD monitor are manufactured using advanced high-precision technol-
ogy, small bright points and anomalous colors may appear, particularly in the vicinity of text. This is normal for
this type of LCD display and does not indicate a malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static electricity,
or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images. This is normal.
115
Restrictions on Camera Settings
The options available in each shooting mode are listed below.
Option
P
S
✔
A
✔
M n r F
Option
P
S
A
M n r F
1
1
OFF
F
H (25600)
H (12800)
6400
5000
4000
3200
2500
2000
1600
800
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
F
(macro mode)
✔
✔
✔
✔
7
AUTO
N
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
7
7
7
7
7
7
7
7
7
✔
✔
✔
✔
✔
✔
B
OFF
O
l
P
✔
✔
✔
✔
N
(flash
mode)
K
L
M
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
B
ON
NISO
d
P
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
640
500
400
200
WB (white balance)
✔
✔
✔
6 fps
3 fps
O
W
X
Y
o
p
q
C
I(continuous)
L (100)
AUTO (3200)
AUTO (1600)
AUTO (800)
AUTO (400)
O
✔
✔
✔
✔
Bracketing
2
2
✔
✔
✔
✔
✔
✔
✔
✔
Metering
OIMAGE SIZE
P
4
Q
✔
✔
✔
FINE
✔
✔
✔
✔
✔
3
Focus mode
S
M
NORMAL
FINE+RAW
NORMAL+RAW
RAW
✔
✔
✔
TIMAGE
QUALITY
7
Exposurre compensation
✔
116
Restrictions on Camera Settings
Option
P
S
A
M n r F
Option
P
S
A
M n r F
7
FRAMING
GUIDLINE
ELECTRONIC
LEVEL
AF DISTANCE
INDICATOR
MF DISTANCE
INDICATOR
HISTOGRAM
APERTURE/
S-SPEED/ISO
EXP. COMPENSA-
TION
PHOTOMETRY
FLASH
WHITE BALANCE
FILM SIMULATION
DYNAMIC RANGE
FRAMES REMAIN-
ING
BATTERY LEVEL
IMAGE SIZE/
QUALITY
AUTO
A
B
C
c
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
UDYNAMIC
RANGE
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
d
e
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
b
PFILM SIMU-
✔
✔
LATION
e
d
vDISP.
CUSTOM
SETTING
f
✔
✔
✔
✔
✔
f
BSELF-TIMER
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
fCOLOR
qSHARPNESS
rHIGHLIIGHT TONE
sSHADOOW TONE
hNOISE REDUCTION
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
KLONG EXPOSURE NR
5
s
t
✔
✔
✔
FAF MODE
5
uSELECT CUSTOM SETTING
KEDIT/SAVE CUSTOM SETTING
117
Restrictions on Camera Settings
1 Fixed at OFF.
2 Fixed at o(multi).
3 Continuous AF is used when S is selected for focus mode.
4 Fixed at Q.
5 Center focus area selected automatically.
6 Automatically optimized for selected shooting mode.
7 Options available vary with shooting mode.
Option
pFLASH MODE
IFLASH
CAF ILLUMINATOR
BRED EYE REMOVAL
IFOCUS RING
UPOWER SAVE MODE
HQUICK SSTART MODE
JCOLOR SPACE
P
S
A
M n r F
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
6
✔
118
Memo
119
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
|