User’s Manual for ELPLL02 Long-Focal Length Zoom Lens
• This long-focal length zoom lens is designed for use only with EPSON
multimedia projectors.
• It makes it possible to increase the distance between the projector and
the screen.
• Please read this manual completely before use to assure maximum per-
formance.
• Note that illustrations may differ slightly from your actual product.
• Specifications are subject to change without notice.
Safety Precautions
To assure that this product is used safely, and to help prevent dam-
age or injury, the following symbols are used in the manual. Please
read this manual thoroughly before use to ensure safety and opti-
mum performance.
Warning
Ignoring this warning, or implementing the content in-
correctly, could result in injury or even death.
Memo Important information, such as additional
explanations, key points to remember, and
things to avoid doing.
9
2. Mounting the zoom lens
Warning
Be sure to disconnect the power cable before installa-
tion, because there is danger of electrical shock.
Memo Always mount and dismount the lens in a
clean room, to minimize the amount of dust.
Excessive dust inside the lens could cause
damage.
• Note that the illustrations below may not match your par-
ticular projector model.
2-1 Removing the current lens
(1) Remove the front case.
1. Remove the two mounting screws, and pull off the front case.
Front case
Screws (two)
11
(2) Remove the current lens.
1. Use the enclosed screwdriver to remove the four mounting
screws, and dismount the current lens.
Current lens
2-2 Mounting the zoom lens
(1) Mounting the zoom lens
1. Remove the rear lens cap.
2. Use the enclosed screwdriver to mount the zoom lens with the
four mounting screws. Be sure that the seal reading “UPPER”
is on top.
Seal
Rear lens cap
12
(2) Mounting the front case
1. Set the front case into position and tighten the two screws.
This completes installation.
• Turn on the power and verify that the projector operates nor-
mally.
Memo Be sure to remove the front lens cap before
turning on the power, or it may melt from the
heat.
13
4. Zoom lens specifications
4-1 Lens specifications
1. Focal length
2. Zoom ratio
3. f number
4. Projection size
5. Mass
68.3 to 116.2 mm
1.7 x
2.14 to 2.98
60 to 300 inches
2100 g
4-2 Appearance with zoom lens mounted
About 505mm
15
User’s Manual for LongThrow Zoom Lens ELPLL03
• This long throw zoom lens is designed for use only with EPSON multi-
media projectors.
• It makes it possible to increase the distance between the projector and
the screen.
• Please read this manual completely before use to assure maximum per-
formance.
• Note that illustrations may differ slightly from your actual product.
• Specifications are subject to change without notice.
Safety Precautions
To assure that this product is used safely, and to help prevent dam-
age or injury, the following symbols are used in the manual. Please
read this manual thoroughly before use to ensure safety and opti-
mum performance.
Warning
Ignoring this warning, or implementing the content in-
correctly, could result in injury or even death.
Memo Important information, such as additional
explanations, key points to remember, and
things to avoid doing.
9
1. Before mounting the zoom lens
1-1 Safety precautions
Warning
Be sure to screw the Long throw zoom lens and adapter
ring down completely. Unless they are securely screwed
on, they could fall off and cause damage or injury (es-
pecially when the projector is ceiling-mounted).
1-2 Check product contents
• Make sure that you have all the parts, as shown below, before starting.
Rear lens cap
Zoom lens
Front lens cap
Screwdriver
User’s manual (this document)
Used to tighter/remove
mounting screws
• In addition to the included screwdriver, you will also need a Phillips
screwdriver, and various other common tools.
Memo Be sure to use a Phillips screwdriver that fits
the screws properly.
10
2. Mounting the zoom lens
Warning
Be sure to disconnect the power cable before installa-
tion, because there is danger of electrical shock.
Memo Always mount and dismount the lens in a
clean room, to minimize the amount of dust.
Excessive dust inside the lens could cause
damage.
• Note that the illustrations below may not match your par-
ticular projector model.
2-1 Remove the current lens
(1) Remove the front case.
1. Remove the two mounting screws, and pull off the front case.
Front case
Screws (two)
11
(2) Remove the current lens.
1. Use the enclosed screwdriver to remove the four mounting
screws, and dismount the current lens.
Current lens
2-2 Mounting the zoom lens
(1) Mounting the zoom lens
1. Remove the rear lens cap.
2. Use the enclosed screwdriver to mount the zoom lens with the
four mounting screws. Be sure that the seal reading “UPPER”
is on top.
Seal
Rear lens cap
12
(2) Mounting the front case
1. Set the front case into position and tighten the two screws.
This completes installation.
• Turn on the power and verify that the projector operates nor-
mally.
Memo Be sure to remove the front lens cap before
turning on the power, or it may melt from the
heat.
13
4. Zoom lens specifications
4-1 Lens specifications
1. Focal length
2. Zoom ratio
3. f number
4. Projection size
5. Mass
144.1 to 194.5mm
1.35 x
2.60 to 3.27
80 to 300 inches
2100 g
4-2 Appearance with zoom lens mounted
About 505mm
15
User’s Manual for ELPLR01 Rear Projector wide Lens
• This wide-angle lens is designed for use only on EPSON multimedia
projectors.
• This lens is designed for use only on rear projection and rear projection
box systems.
• Please read this manual completely before use to assure maximum per-
formance.
• Note that illustrations may differ slightly from your actual product.
• Specifications are subject to change without notice.
Safety Precautions
To assure that this product is used safely, and to help prevent dam-
age or injury, the following symbols are used in the manual. Please
read this manual thoroughly before use to ensure safety and opti-
mum performance.
Warning
Ignoring this warning, or implementing the content in-
correctly, could result in injury or even death.
Memo Important information, such as additional
explanations, key points to remember, and
things to avoid doing.
11
1. Before mounting the wide-angle lens
1-1 Safety precautions
Warning
Be sure to screw the Rear Projector wide lens and
adapter ring down completely. Unless they are securely
screwed on, they could fall off and cause damage or
injury (especially when the projector is ceiling-mounted).
1-2 Check product contents
• Make sure that you have all the parts, as shown below, before starting.
Screwdriver
Rear lens cap
Zoom lens
Front lens cap
Used to tighter/remove
mounting screws
Hex wrench
User’s manual (this document)
Used to loosen and tighten
the ring mounting screws.
• In addition to the included screwdriver, you will also need a Phillips
screwdriver, and various other common tools.
Memo Be sure to use a Phillips screwdriver that fits
the screws properly.
12
2. Mounting the rear-projection wide-angle lens
Warning
Be sure to disconnect the power cable before installa-
tion, because there is danger of electrical shock.
Memo Always mount and dismount the lens in a
clean room, to minimize the amount of dust.
Excessive dust inside the lens could cause
damage.
• Note that the illustrations below may not match your particu-
lar projector model.
2-1 Removing the current lens
(1) Remove the front case.
1. Remove the two mounting screws, and pull off the front case.
Front case
Screws (two)
13
(2) Remove the current lens.
1. Use the enclosed screwdriver to remove the four mounting
screws, and dismount the current lens.
Current lens
2-2 Mounting the rear-projection wide-angle lens
(1) Mounting the rear-projection wide-angle lens
1. Remove the rear lens cap.
2. Use the enclosed screwdriver to mount the rear projector wide
lens with the four mounting screws. Be sure that the seal read-
ing “UPPER” is on top.
Seal
Rear lens cap
14
(2) Adjusting the wide lens for a rear projector
• This lens must be adjusted to match the screen size. Adjust the
lens as follows, before installing the front case.
1. Turn the lens shift button to move the lens all the way down.
2. Loosen the 2 focus ring mounting screws by using the hex wrench
that came in the same package.
3. Loosen the 2 resolving plane correction ring mounting screws
with the hex wrench.
4. Turn on the projector power.
5. Rotate the two rings to adjust the image to the optimum appear-
ance. The resolving plane correction ring should provide a sharp
image across the entire screen area.
6. Use the hex wrench to retighten the four ring mounting screws.
7. Turn off the power, and disconnect the power cable.
WARNING
DO NOT TOUCH!
Lens shift button
Resolving plane
correction ring
Focus ring
Focus ring mounting screws
Resolving plane correction ring
mounting screws
Warning
Turn the power only when adjusting the lens. Always
disconnect the power cable at other times.
When adjusting the lens, take care not to touch any
other parts of the projector or lens, as there is a danger
of electric shock with the front case open.
Memo Be sure to remove the front lens cap before
turning on the power, or it may melt from the
heat.
15
(3) Mounting the front case
1. Set the front case into position and tighten the two screws.
This completes installation.
• Turn on the power and verify that the projector operates nor-
mally.
16
4. Rear-projection wide-angle lens specifications
4-1 Lens specifications
1. Focal length
2. f number
27mm
2.3
3. Projection size
4. Mass
60 to 100 inches
1600 g
4-2 Appearance with rear projector wide lens mounted
About 455mm
18
User’s Manual for ELPLS01 Standard Lens
• This standard lens is designed for use only with EPSON multimedia pro-
jectors.
• Please read this manual completely before use to assure maximum per-
formance.
• Note that illustrations may differ slightly from your actual product.
• Specifications are subject to change without notice.
Safety Precautions
To assure that this product is used safely, and to help prevent dam-
age or injury, the following symbols are used in the manual. Please
read this manual thoroughly before use to ensure safety and opti-
mum performance.
Warning
Ignoring this warning, or implementing the content in-
correctly, could result in injury or even death.
Memo Important information, such as additional
explanations, key points to remember, and
things to avoid doing.
9
1. Before mounting the standard lens
1-1 Safety precautions
Warning
Be sure to screw the Long-Focal Length lens and
adapter ring down completely. Unless they are securely
screwed on, they could fall off and cause damage or
injury (especially when the projector is ceiling-mounted).
1-2 Check product contents
• Make sure that you have all the parts, as shown below, before starting.
Rear lens cap
Standard lens
Front lens cap
Screwdriver
User’s manual (this document)
Used to tighter/remove
mounting screws
• In addition to the included screwdriver, you will also need a Phillips
screwdriver, and various other common tools.
Memo Be sure to use a Phillips screwdriver that fits
the screws properly.
10
2. Mounting the standard lens
Warning
Be sure to disconnect the power cable before installa-
tion, because there is danger of electrical shock.
Memo Always mount and dismount the lens in a
clean room, to minimize the amount of dust.
Excessive dust inside the lens could cause
damage.
• Note that the illustrations below may not match your par-
ticular projector model.
2-1 Removing the current lens
(1) Remove the front case.
1. Remove the two mounting screws, and pull off the front case.
Front case
Screws (two)
11
(2) Remove the current lens.
1. Use the enclosed screwdriver to remove the four mounting
screws, and dismount the current lens.
Current lens
2-2 Mounting the standard lens
(1) Mounting the standard lens
1. Remove the rear lens cap.
2. Use the enclosed screwdriver to mount the standard lens with
the four mounting screws. Be sure that the seal reading “UP-
PER” is on top.
Seal
Rear lens cap
12
(2) Mounting the front case
1. Set the front case into position and tighten the two screws.
This completes installation.
• Turn on the power and verify that the projector operates nor-
mally.
Memo Be sure to remove the front lens cap before
turning on the power, or it may melt from the
heat.
13
4. Standard lens specifications
4-1 Lens specifications
1. Focal length
2. Zoom ratio
3. f number
4. Projection size
5. Mass
49.2 to 68.9 mm
1.4 x
1.84 to 2.36
30 to 300 inches
1300 g
4-2 Appearance with standard lens mounted
About 475mm
15
User's Manual for the ELPLW01 Wide Zoom Lens
• This wide zoom lens is designed for use only with EPSON multimedia
projectors.
• It makes it possible to decrease the distance between the projector and
the screen.
• Please read this manual completely before use to assure maximum per-
formance.
• Note that illustrations may differ slightly from your actual product.
• Specifications are subject to change without notice.
Safety Precautions
To assure that this product is used safely, and to help prevent dam-
age or injury, the following symbols are used in the manual. Please
read this manual thoroughly before use to ensure safety and opti-
mum performance.
Warning
Ignoring this warning, or implementing the content in-
correctly, could result in injury or even death.
Memo Important information, such as additional
explanations, key points to remember, and
things to avoid doing.
9
1. Before mounting the zoom lens
1-1 Safety precautions
Warning
Be sure to screw the Long-Focal Length lens and
adapter ring down completely. Unless they are securely
screwed on, they could fall off and cause damage or
injury (especially when the projector is ceiling-mounted).
1-2 Check product contents
• Make sure that you have all the parts, as shown below, before starting.
Rear lens cap
Zoom lens
Front lens cap
Screwdriver
User’s manual (this document)
Used to tighter/remove
mounting screws
• In addition to the included screwdriver, you will also need a Phillips
screwdriver, and various other common tools.
Memo Be sure to use a Phillips screwdriver that fits
the screws properly.
10
2. Mounting the zoom lens
Warning
Be sure to disconnect the power cable before installa-
tion, because there is danger of electrical shock.
Memo Always mount and dismount the lens in a
clean room, to minimize the amount of dust.
Excessive dust inside the lens could cause
damage.
• Note that the illustrations below may not match your par-
ticular projector model.
2-1 Removing the current lens
(1) Remove the front case.
1. Remove the three mounting screws, and pull off the front case.
The two components will separate from each other.
Front case
Screws (three)
11
(2) Remove the current lens.
1. Use the enclosed screwdriver to remove the four mounting
screws, and dismount the current lens.
Current lens
2-2 Mounting the zoom lens
(1) Mounting the zoom lens
1. Remove the rear lens cap.
2. Use the enclosed screwdriver to mount the zoom lens with the
four mounting screws. Be sure that the seal reading "UPPER" is
on top.
Seal
Rear lens cap
12
(2) Mounting the front case
1. Set the front case into position and tighten the three screws.
This completes installation.
• Turn on the power and verify that the projector operates nor-
mally.
Memo • Be sure to remove the front lens cap be-
fore turning on the power, or it may melt
from the heat.
• When handling the zoom lens, take care
not to catch your finger between the lens
and the tabletop.
13
4. Zoom lens specifications
4-1 Lens specifications
1. Focal length
2. Zoom ratio
3. f number
4. Projection size
5. Mass
37.9 to 45.5 mm
1.2 x
2.34 to 2.65
60 to 200 inches
2600 g
4-2 Appearance with zoom lens mounted
About 480mm
15
|