Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide
(separate volume) carefully to familiarize yourself with safe and
effective usage.
Please refer to the Setup Guide for basic information ranging from
connection of the monitor to a PC or external device to using the
monitor.
•
•
The latest User’s Manual is available for download from our web site:
Notice for this monitor
This product is suited to general purposes like creating documents, viewing multimedia content.
This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more
after the monitor power has been turned on.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on
the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a fixed lifetime. When the screen becomes dark or begins to flicker, please contact
your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference
patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure
marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until
the dew condensation disappears, otherwise it may cause some damage to the monitor.
3
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or
panel, and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
Note
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with
water.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according
to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
4
CONTENTS
CONTENTS............................................................. 5
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
CONTENTS
5
CONTENTS
6
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• 23″ wide format LCD
• Applicable to the resolution of 1920 × 1080.
• Panel with a wide field of view adopted
VA panel with 178º horizontal and vertical viewing angles.
• HDMI connector × 2
Applicable to the PC input signal using HDMI input, allowing three different digital signal inputs from a PC.
-
• The Color Mode function allows the user to select the display mode optimum to the displayed image.
The Paper mode reproduces an easy-on-the-eyes display that looks just like printed paper.
-
• ContrastEnhancer function
Automatically adjusts the contrast according to the image, enabling the display of high contrast and sharp animated
images.
• Power Resolution function
You can reduce image blur by enhancing its outline.
• Two dedicated gamma modes (“Power1”/“Power2”) suitable for game images implemented
The images will be sharpened by increasing the halftone (Power1) and low-tone (Power2) contrasts.
• A variety of Screen Size can be selected, such as dot by dot (image is displayed without scaling the input
signals), Letterbox, Overscan (change of the display area of the input image)
• The software “ScreenManager Pro for LCD (DDC/CI)” to adjust the screen using the mouse and keyboard
is included.
• Remote control enables easy operation, setting and adjustment of the monitor.
• Color sheets (in three colors) to be pasted at the bottom of the monitor included
Select your desired color to add an accent to the monitor.
See “Setup Guide”.
• HDCP (High-bandwidth Digital Content Protection)
• Built-in stereo speakers and headphone jack
Chapter1Introduction
7
1-2. Controls and Functions
Monitor
Menu
Color
Screen
Sound
PowerManager
Monitor Settings
Information
Settingmenu*1
12
14
13
1 2
3
4
5 6
7
8
9
10
11
2. Remote control
Receivesthesignalfromtheremotecontrol.
detector
3.
button
PC1(DVI)→PC2(D-SUB)→HDMI1→HDMI2
button Displaysthevolumeadjustmentmenutovolumeupordown.
Turnsthepoweronoroff.
4.
5.
/
button
Indicatesthemonitor’soperationstatus.
Blue:
Orange:
Red
Operating
Powersavingmode
Poweroff
6. Power indicator
OFF:
Mainpoweroff
7. Main power switch
8. Power connector
Turnsthemainpoweronoroff.
Connectsthepowercord.
Left:HDMIconnector×2(HDMI1,HDMI2)/Center:DVI-Dconnector/
Right:D-Submini15-pinconnector
9. Input signal connector
10. Stereo mini jack
11. Headphone jack
12. Security lock slot
13. Stand*2
Connectsthestereominijackcable.
Connectstheheadphones.
ComplieswithKensington’sMicroSaversecuritysystem.
Usedtoadjusttheangleofthemonitorscreen.
Outputsaudiosource.
14. Speaker
*2Anoptionalarm(oranoptionalstand)canbeattachedbyremovingthestand(see“7-1.HowtoAttachtheOptional
Chapter1Introduction
8
Remote Control
2
3
1. OFF TIMER
2. DISPLAY
Setsthetimeuntilthemonitorpower-off.
Displaysthecurrentinputport.
Changesthescreensize.
3. SCREEN SIZE
4. POWER
1
5
4
6
Turnsthepoweronoroff.
5. INPUT SELECT Switchesinputsignalsfordisplay.
PC
PC1(DVI)→PC2(D-SUB)
HDMI1→HDMI2
8
9
HDMI
7
6. MUTE
Mutessoundtemporarily.
7. VOLUME +/-
8. MENU
Adjuststhevolume.
10
11
12
13
Displays/ExitstheSettingmenu.
Returnstothepreviousmenuinmenuoperation.
9. RETURN
• Choosesandincreases/decreasesadjustmentsettings
foradvancedadjustmentusingtheSettingmenu.
17).
10.
/
/
/
Determinesanitemonthemenuscreen,andsaves
valuesadjusted.
11. ENTER
12. MODE
Changesthecolormode.
13. EcoView
Displays/ExitstheEcoViewmenu.
Before Using Remote Control
How to install battery
●
1. While pushing the tab toward the arrow (1), pull out the
battery case (2).
(1)
(2)
2. Insert a battery with the positive side up. (Battery model
number: CR2032)
3. Insert the battery case until it clicks.
Receivable Range of Remote Control
Use the remote control inside of the range as below.
5m
20°
20°
7m
30°
30°
5m
5m
5m
7m
Chapter1Introduction
9
1-3. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk
contents and the overview of the software programs.
Disk contents and software overview
●
The disk includes software programs for adjustment, and User’s Manual. Refer to Readme.txt file on the disk
for software startup procedures or file access procedures.
Windows Macintosh
Item
Overview
AReadme.txtfile
√
√
√
√
Screenadjustmentpatternfiles
Usedwhenadjustingtheimageofanalog
signalinputmanually.
ScreenManagerProforLCD(DDC/
CI)
Softwareforadjustingthescreenusingthe
mouseandkeyboard
√
-
ThissoftwaredoesnotrunonaPC
connectedviatheHDMIinput.
EIZOScreenSlicer
Softwarethatdividesascreenandlaysout
multiplewindowsefficiently.
√
√
-
User’sManualofthismonitor(PDFfile)
√
To use “ScreenManager Pro for LCD(DDC/CI)/EIZO ScreenSlicer”
●
For the installation and use of “ScreenManager Pro for LCD(DDC/CI)/EIZO SceenSlicer”, refer to the
respective User’s Manual on the disk.
Chapter1Introduction
10
1-4. Basic Operations and Functions
Basic operation of the Setting menu
●
Displaying the Setting menu
1.
1. Press
on the remote control. The Setting menu appears.
Menu
Color
Screen
Sound
PowerManager
Monitor Settings
Information
Adjusting/Setting
1. Choose a menu to adjust/set with
2.
,
, and then press
. The Sub menu appears.
Color
Return
Color Mode
[
[
[
[
[
[
[
U se r1
8 0
7 5
5 0
0
0
Of f
]
]
]
]
]
]
]
Brightness
Black Level
Contrast
Saturation
Hue
Temperature
Advanced Settings
Color Reset
2. Choose an item to adjust/set with
,
, and then press
. The adjustment/ setting menu appears.
Brightness
60
3. Adjust/set the selected item with
,
,
,
, and then press
.
Exiting
1. Press
3.
.
Note
• To go back to the previous menu, press
.
Chapter1Introduction
11
Functions
●
The following table shows all the Setting menu’s adjustment and setting menus.
Main menu
Setting
Reference
Color*1
ColorMode
Brightness
BlackLevel
Contrast
Saturation
Hue
Temperature
AdvancedSettings ContrastEnhancer
PowerResolution
Gamma
Gain
Overdrive
ColorReset
Screen
AutoScreenAdjust*2
AutoRangeAdjust*2
Clock*2
Phase*2
Position*2
ColorSpace*3
Smoothing
Sound
Source*3
SoundLevel
PowerSave
PowerSave
DDC/CI
PowerManager
MonitorSettings
KeyLock
Logo
PowerIndicator
Language
Reset
Information
*1Theadjustment/settingsavailableonthe“Color”menudependontheselectedColormode.Theabove
tableshowsthesubmenuswhentheUser1orUser2modeisselected.
*2Thesefunctionscanbeadjustedwithanaloginput.
*3ThisfunctionisavailablewithHDMIsignalinput.
Chapter1Introduction
12
Chapter 2 Adjusting Screens
2-1. Compatible Resolutions/Formats
The monitor supports the following resolutions and signal format.
Analog Input (D-Sub)
Vertical Scan
Frequency
upto75Hz
70Hz
Resolution
Applicable Signals
Dot Clock
640×480
720×400
VGA,VESA,CEA-861
VGATEXT
800×600
VESA
VESA
CEA-861
VESA
VESA
upto75Hz
upto75Hz
60Hz
60Hz
upto75Hz
60Hz
1024×768
1280×720
1280×960
1280×1024
1680×1050
1920×1080*
148.5MHz
(Max.)
VESACVT,VESACVTRB
CEA-861
60Hz
Digital Input (DVI-D, HDMI: PC signal)
Vertical Scan
Frequency
60Hz
Resolution
Applicable Signals
Dot Clock
640×480
720×400
800×600
VGA,CEA-861
VGATEXT
VESA
70Hz
60Hz
1024×768
1280×720
1280×960
1280×1024
1680×1050
1920×1080*
VESA
CEA-861
VESA
VESA
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
148.5MHz
(Max.)
VESACVT,VESACVTRB
CEA-861
A graphics board in conformance with the VESA and CEA-861 standards is required.
*Recommended resolution
Digital Input (HDMI: video signal)
• Video signal
VGA / 525i (480i)/525p (480p)/1125i (1080i)/750p (720p)/1125p (1080p): 60 Hz
625i (576i)/625p (576p)/1125i (1080i)/750p (720p)/1125p (1080p): 50 Hz
-
-
• Audio signal
2ch linear PCM (32 kHz / 44.1 kHz / 48 kHz)
-
Chapter2AdjustingScreens
13
2-2. Setting the Resolution
When you connect the monitor to the PC and find that the resolution is improper, or when you want to change
the resolution, follow the procedure below.
Windows 7
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Screen resolution”.
3. On the “Screen Resolution” dialog box, select the monitor.
4. Click “Resolution” to select the desired resolution.
5. Click the [OK] button.
6. When a confirmation dialog box is displayed, click [Keep changes].
Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the
“Resolution” field.
5. Click the [OK] button.
6. When a confirmation dialog box is displayed, click [Yes].
Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired
resolution for “Screen resolution” under “Display”.
4. Click the [OK] button to close the dialog box.
Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions”
field.
4. Your selection will be reflected immediately. When you are satisfied with the selected resolution, close
the window.
Chapter2AdjustingScreens
14
2-3. Adjusting Color
To select the display mode (Color Mode)
●
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode
Purpose
User1
User2
sRGB
Paper
Game
Selectoneoftheseusermodestodefineadesiredsetofparametersettings.
SuitableforcolormatchingwithsRGBcompatibleperipherals.
Producesaprintedpapereffectbydecreasingcontrastandcolortemperature.
Suitablefordisplayinggameimages.
Cinema
Suitablefordisplayingmovie-likeimages.
Displaysthecurrentmode.
Color Mode
User1
Procedure
1. Press
on the remote control.
The mode name appears at the center of the screen.
2. The mode among the list is highlighted in turn each time
is pressed.
You can switch the current mode with
or
while the mode menu is being displayed.
→User1←→User2←→sRGB←→Paper←→Game←→Cinema←
Note
• The Setting menu and the Mode menu cannot be displayed at the same time.
• “ScreenManager Pro for LCD (DDC/CI)” allows you to select the Color mode automatically according to the
application used (see “Chapter 3 Auto Fine-Contrast” in the “ScreenManager Pro for LCD (DDC/CI)” User’s
Manual).
Chapter2AdjustingScreens
15
To perform advanced adjustments
●
The “Color” menu of the Setting menu allows you to set and save the independent color adjustment for each
mode.
Attention
• The monitor will take about 30 minutes before its internal electric components stabilize. Wait 30 minutes or more
after turning the monitor power on before starting adjustment.
• Perform the range adjustment first when adjusting color for analog signals (see “To adjust color gradation
• The same image may be seen in different colors on multiple monitors due to their monitor-specific characteristics.
Make fine color adjustment visually when matching colors on multiple monitors.
Note
• The value shown in “K” is available only as reference.
• Using the “ScreenManager Pro for LCD (DDC/CI)” allows you to perform the color adjustment by using the mouse
and keyboard of your PC. (Refer to “Chapter 4 Color Adjustment” in the User’s Manual for “ScreenManager Pro for
LCD (DDC/CI)”.)
Adjustable settings in each mode
●
The adjustable settings depend on the mode. (You cannot select any non-adjustable or non-settable function.)
For instructions on how to adjust or set each function, refer to subsequent pages.
√: Adjustable -: Not adjustable
Color Mode
Function
User1
User2
sRGB
Paper
Game
Cinema
Brightness
BlackLevel
Contrast
√
√
√
√
√
√
√
√
√
√
√
√
√
-
√
-
√
√
√
√
√
√
√
√
√
-
√
√
√
√
√
√
√
√
-
-
-
Saturation
Hue
-
-
-
-
Temperature
-
√
-
AdvancedSettings ContrastEnhancer
-
PowerResolution
-
-
Gamma
-
-
Gain
Overdrive
-
-
-
-
-
√
√
-
ColorReset
√
√
√
Chapter2AdjustingScreens
16
To adjust brightness “Brightness”
●
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD
back panel).
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Brightness” in the “Color” menu, and press
The “Brightness” menu appears.
.
3. Use
or
for adjustment.
4. Press
to exit the adjustment.
Note
• While the Setting menu is not displayed,
or
on the remote control is available for adjustment.
• If you feel that the image is too bright even if the brightness is set to 0 or that the image is too dark even if the
brightness is set to 100, adjust the contrast.
To adjust black level “Black Level”
You can adjust the black level of images.
Adjustable range
●
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Black Level” in the “Color” menu, and press
The “Black Level” menu appears.
.
3. Use
or
for adjustment.
4. Press
to exit the adjustment.
Note
• After completing black level adjustment, readjust the contrast as appropriate.
Chapter2AdjustingScreens
17
To adjust contrast “Contrast”
●
The brightness of the screen is adjusted by varying the video signal level.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press
2. Choose “Contrast” in the “Color” menu, and press
The “Contrast” menu appears.
.
.
3. Use
or
for adjustment.
4. Press
to exit the adjustment.
Note
• In the contrast of 50, every color gradation is displayed (for PC input signal only).
• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the
gradation characteristics, prior to the contrast adjustment.
• Perform the contrast adjustment in the following cases.
- When you feel the image is too dark even if the brightness is set to 100 (Set the contrast to higher than 50.)
- When you feel the image is too bright even if the brightness is set to 0 (Set the contrast to lower than 50.)
To adjust the color saturation “Saturation”
●
This function allows you to adjust color saturation.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press
2. Choose “Saturation” in the “Color” menu, and press
The “Saturation” menu appears.
.
.
3. Use
or
for adjustment.
4. Press
to exit the adjustment.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The minimum value (-50) changes the screen to monochrome.
Chapter2AdjustingScreens
18
To adjust hue “Hue”
This function allows you to adjust hue.
Adjustable range
-50 to 50
●
Procedure
1. Choose “Color” in the Setting menu, and press
2. Choose “Hue” in the “Color” menu, and press
The “Hue” menu appears.
.
.
3. Use
or
for adjustment.
4. Press
to exit the adjustment.
Attention
• Using this function may make some color gradations unavailable for display.
To adjust color temperature “Temperature”
●
Color temperature can be adjusted.
The color temperature is normally used to express the hue of “White” and/or “Black” by a numerical value.
The value is expressed in degrees “K” (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the flame
temperature. A gain preset value is set for each color temperature setting value.
Adjustable range
Off, 4000K-10000K (specified by every 500K unit, including 9300K)
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Temperature” in the “Color” menu, and press
The “Temperature” menu appears.
.
3. Use
or
for adjustment.
4. Press
to exit the adjustment.
Note
• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).
• When gain is changed, the color temperature is changed to “Off”.
Chapter2AdjustingScreens
19
To set ContrastEnhancer “ContrastEnhancer”
●
This function allows you to set whether to automatically adjust the contrast according to the darkness or
brightness of a scene, for example.
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Advanced Settings” in the “Color” menu, and press
.
3. Choose “ContrastEnhancer” in the “Advanced Settings” menu, and press
The “ContrastEnhancer” menu appears.
.
4. Select “Enable” or “Disable” with
or
.
5. Press
to exit the adjustment.
Note
• Setting “Enable” allows you to display high contrast and sharp images.
To reduce image blur “Power Resolution”
You can reduce image blur by enhancing its outline.
Adjustable range
●
Off, 1, 2, 3
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Advanced Settings” in the “Color” menu, and press
.
3. Choose “Power Resolution” in the “Advanced Settings” menu, and press
The “Power Resolution” menu appears.
.
4. Use
or
for adjustment.
5. Press
to exit the adjustment.
Note
• If you keep pressing the
monitor enters the demo mode. To return to normal display, keep pressing
or
button for two seconds or more while “Power Resolution” is displayed, the
or for at least two seconds.
- Left half of screen:
- Right half of screen:
Power Resolution On
Power Resolution Off
Chapter2AdjustingScreens
20
To adjust gamma “Gamma”
●
Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the
variation rate is not proportional to the input signal. To keep the balance between the input signal and the
brightness of the monitor is called as “Gamma correction”.
Adjustable range
1.8, 2.0, 2.2, 2.4, 2.6, 2.8, Power1, Power2
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Gamma” in the “Advanced Settings” menu, and press
The “Gamma” menu appears.
.
.
4. Use
or
for adjustment.
5. Press
to exit the adjustment.
Note
• Choosing “Power1” will help to sharpen halftone images by increasing their contrast.
• Choosing “Power2” will help to make dark images visible by increasing the low-tone contrast.
To adjust gain “Gain”
●
The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of
“white” by adjusting gain.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Gain” in the “Advanced Settings” menu, and press
The “Gain” menu appears.
.
.
4. Adjust gain with
or
for each of red, green, and blue.
5. Press
to exit the adjustment.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The value of gain changes with that of color temperature.
• When gain is changed, the color temperature is changed to “Off”.
Chapter2AdjustingScreens
21
To set overdrive intensity “Overdrive”
●
This function allows you to set overdrive intensity based on the use of the monitor. You can reduce Image
lags by setting it to “Enhanced” when displaying animated images.
Adjustable range
Enhanced, Standard, Off
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Overdrive” in the “Advanced Settings” menu, and press
The “Overdrive” menu appears.
.
.
4. Use
or
for adjustment.
5. Press
to exit the adjustment.
Attention
• The overdrive function is disabled in the following cases:
- The vertical scan frequency of input signals is more than 60 Hz
- The screen size is “Normal” (excluding the case that the display resolution is 1920 x 1080) or “Letterbox”
2-4. Screen Adjustment
Digital Signal Input
●
When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if
When performing more advanced adjustment, see “2-3. Adjusting Color” (page 15) and subsequent pages.
Analog Signal Input
●
Attention
• The monitor will take about 30 minutes before its internal electric components stabilize. Wait 30 minutes or more
after turning the monitor power on before starting adjustment.
• The Self Adjust (automatic screen adjustment) function does not work for the images under the resolution of 800 ×
600 (SVGA).
• The self adjustment (or automatic screen adjustment) function works correctly when an image is fully displayed over
the Windows or Macintosh display area. They do not work properly in the cases below:
- When an image is displayed only on a part of the screen (command prompt window, for example)
- When a black background (wallpaper, etc.) is in use
Also, these functions cannot work properly in some graphic boards.
The monitor screen adjustment is used to suppress flickering of the screen or adjust screen position and
screen size correctly according to the PC to be used.
Note
• The Self Adjust function works when all of the following conditions are satisfied:
- When a signal is input into the monitor for the first time or when a resolution or vertical/horizontal scan frequency
not used before is set
If the screen is not displayed correctly even after performing the Self Adjust operation, adjust the screen
according to the procedures on the following pages to use the monitor comfortably.
Chapter2AdjustingScreens
22
Setting Procedures
Perform the auto adjustment.
1.
To adjust flickering, screen position, and screen size automatically “Auto Screen
●
Adjust”
Procedure
1. Choose “Screen” in the Setting menu, and press
2. Choose “Auto Screen Adjust” in the “Screen” menu, and press
3. Select “Yes” with or , and press
.
.
.
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
Ifthescreenisnotdisplayedcorrectlyevenafterperforming“1.Performtheautoadjustment.”(page23),
performtheadjustmentsaccordingtotheproceduresonthefollowingpages.Ifthescreenisdisplayed
Prepare to use analog screen adjustment patterns.
2.
Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern files”.
Note
• For details and instructions on opening the “Screen adjustment pattern files”, refer to the Readme.txt file.
Perform the auto adjustment again with the analog screen adjustment pattern
displayed.
3.
To adjust flickering, screen position, and screen size automatically “Auto Screen
Adjust”
●
Procedure
1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern files”.
2. Choose “Screen” in the Setting menu, and press
3. Choose “Auto Screen Adjust” in the “Screen” menu, and press
4. Select “Yes” with or , and press
.
.
.
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
Ifthescreenisnotdisplayedcorrectlyevenafterperforming“3.Performtheautoadjustmentagain
withtheanalogscreenadjustmentpatterndisplayed.”(page23),performtheadjustmentsaccordingto
theproceduresonthefollowingpages.Ifthescreenisdisplayedcorrectly,goto“5.Adjustingcolor
Chapter2AdjustingScreens
23
Choose “Screen” from the Setting menu to perform advanced adjustments.
4.
Adjust the clock, phase and position, in this order.
To eliminate vertical bars “Clock”
Procedure
●
1. Choose “Clock” in the “Screen” menu, and press
The “Clock” menu appears.
.
2. Adjust the clock with
or
to eliminate vertical bars.
Press
or
slowly so as not to miss the adjustment point.
3. Press
to exit the adjustment.
When blurring, flickering or bars appear on the screen after adjustment, proceed to “Phase” to remove flickering or
blurring.
To remove flickering or blurring “Phase”
Procedure
●
1. Choose “Phase” in the “Screen” menu, and press
The “Phase” menu appears.
.
2. Adjust the phase with
or
to minimize flickering or blurring.
3. Press to exit the adjustment.
When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars “Clock””.
(Clock → Phase → Position)
Attention
• Flickering or blurring may not be eliminated depending on your PC or graphics board.
Chapter2AdjustingScreens
24
To correct the screen position “Position”
●
Note
• Since the number of pixels and the pixel positions are fixed on the LCD monitor, only one position is provided to
display images correctly. The position adjustment is made to shift an image to the correct position.
Procedure
1. Choose “Position” in the “Screen” menu, and press
The “Position” menu appears.
.
2. Adjust the position with
/
/
/
.
3. Press to exit the adjustment.
4. Close Pattern 1.
Adjusting color gradation.
5.
To adjust color gradation automatically “Auto Range Adjust”
●
Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
Procedure
1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern files”.
2. Choose “Screen” in the Setting menu, and press
.
3. Choose “Auto Range Adjust” in the “Screen” menu, and press
The “Auto Range Adjust” menu appears.
.
4. Select “Yes” with
or
, and press
.
The output range is set automatically.
5. Close Pattern 2.
Chapter2AdjustingScreens
25
Modify blurred characters or lines.
6.
To modify blurred characters/lines “Smoothing”
●
When an image is displayed with a resolution other than recommended, the characters or lines of the
displayed image may blur.
Attention
• Smoothing setting may not be required depending on the display resolution. (You cannot choose the smoothing icon.)
Adjustable range
1 to 5
Procedure
1. Choose “Screen” in the Setting menu, and press
.
2. Choose “Smoothing” in the “Screen” menu, and press
The “Smoothing” menu appears.
.
3. Use
or
for adjustment.
4. Press
to exit the adjustment.
2-5. Screen Size Changing
Analog Input (D-Sub)/Digital Input (DVI-D, HDMI: PC signal)
●
The image with the resolution other than the recommended resolution is displayed in full screen
automatically. You can change the screen size by using the “Screen Size” function.
Setting
Function
FullScreen
Displaysanimageinfullscreen.Imagesaredistortedinsomecasesbecausethe
verticalrateisnotequaltothehorizontalrate.
Enlarged
Normal
Displaysanimageinfullscreen.Insomecases,ablankhorizontalorverticalborder
appearstoequalizetheverticalrateandthehorizontalrate.
Displaysimageswiththespecifiedresolution.
Example: Image size 1024 × 768
FullScreen
Enlarged
Normal
(1920×1080)
(1440×1080)
(1024×768)
Procedure
1. Press
on the remote control.
Each time you press
, the size changes.
Attention
• Selecting “Normal” may make some color gradations unavailable for display.
Chapter2AdjustingScreens
26
Digital Input (HDMI: video signal)
●
The screen size can be changed with the “Screen Size” function.
Setting
Function
Screen Display
Auto
Themonitorautomaticallychangesthescreen
sizeaccordingtotheaspectratioandresolution
informationfromtheexternaldevice.Thiscanbeset
onlyforHDMI(SDSignal)input.
FullScreen
Enlarged
Displaysanimageinfullscreen.Imagesare
distortedinsomecasesbecausetheverticalrateis
notequaltothehorizontalrate.
Displaysanimageinfullscreen.Insomecases,
ablankhorizontalorverticalborderappearsto
equalizetheverticalrateandthehorizontalrate.
Letterbox
DisplaysLetterboxof16:9infullscreen.Exceptfor
Letterbox,theupperandlowerpartsoftheprojected
imagearecut.ThiscanbesetonlyforHDMI(SD
Signal)input.
Normal*1
Theimageisdisplayedwithoutscalingtheinput
signals.
*1When“ScreenSize”is“Normal”,“Overscan”isfixedat“Off”.
Procedure
1. Press
on the remote control.
Each time you press
, the size changes.
Attention
• Selecting “Normal” may make some color gradations unavailable for display.
To set the screen ratio “Overscan”
In order to hide distortion or noise at the image’s edge, the display area of the input image can be changed so
that peripheral images are not displayed.
Setting
Function
On
Off
Displaysaninputimageinthescreenbytrimmingtheverticalandhorizontalpartsofthe
image.
Displaysmostoftheinputimage.
Procedure
1. Press
on the remote control.
The “Screen Size” menu appears.
2. Select “Overscan” with
.
3. Use
or
for adjustment.
4. Press
to exit the adjustment.
Attention
• When “Screen Size” is “Normal”, “Overscan” is fixed at “Off”.
Chapter2AdjustingScreens
27
Chapter 3 Setting Monitor
3-1. Adjusting Volume
To turn the volume up/down
●
This function allows you to adjust the volume.
Adjustable range
0 to 30
Procedure
1. Press
or
on the remote control.
Note
• Alternatively, you can use
8)).
or
on the monitor for adjustment. (see “1-2. Controls and Functions” (page
• The volume for the HDMI1, HDMI2, and the stereo mini jack can be set individually.
To mute the sound temporarily
Procedure
●
1. Press
on the remote control.
Mute sound temporarily.
By pressing the button again or pressing
, the sound comes back.
Note
• The mute setting can also be released by pressing
• While the monitor is muted, press or
on the monitor.
on the monitor to decrease the volume setting.
3-2. Switching sound source for HDMI signal input
“Source”
This function allows you to switch sound source for HDMI signal input. You can select the HDMI or stereo
mini jack.
Procedure
1. Choose “Sound” in the Setting menu, and press
2. Choose “Source” in the “Sound” menu, and press
The “Source” menu appears.
.
.
3. Select “HDMI” or “Stereo Mini Jack” with
or
.
4. Press
to exit the adjustment.
Note
• This function is available with HDMI signal input. However, if a DVI-HDMI adapter cable is used, the sound source
is automatically “Stereo Mini Jack” and cannot be changed.
Chapter3SettingMonitor
28
3-3. To adjust the sound level “Sound Level”
The input sound level can be adjusted.
The volume difference may occur depending on the kinds of input signals, since the average sound level of the
external device differs.
Adjustable range
-1 to 1
Procedure
1. Choose “Sound” in the Setting menu, and press
.
2. Choose “Sound Level” in the “Sound” menu, and press
The “Sound Level” menu appears.
.
3. Use
or
for adjustment.
4. Press
to exit the adjustment.
Note
• For example, if the volume difference of PC1 and PC2 input signals becomes large, you can reduce the volume
difference between them by raising the “Sound Level” of the lower volume side.
3-4. Enabling/Disabling DDC/CI communication
“DDC/CI”
This function allows you to enable/disable the DDC/CI communication (see “7-5. Glossary” (page 46)).
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “DDC/CI” in the “Monitor Settings” menu, and press
The “DDC/CI” menu appears.
.
.
3. Select “Enable” or “Disable” with
or
.
4. Press
to exit the adjustment.
Note
• HDMI input does not support DDC/CI communication.
3-5. Locking Buttons “Key Lock”
This function allows you to lock the buttons on the monitor.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “Key Lock” in the “Monitor Settings” menu, and press
The “Key Lock” menu appears.
.
.
3. Select “On” with
or
.
4. Press
to exit the adjustment.
Note
• The following operations are available even if the buttons are locked:
- Turning on or off the monitor with the Power button
• Does not lock the remote control operation.
Chapter3SettingMonitor
29
3-6. Setting the EIZO Logo Display “Logo”
When the monitor is turned on, the EIZO logo appears on the screen. You can choose to display or not to
display the EIZO logo.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “Logo” in the “Monitor Settings” menu, and press
The “Logo” menu appears.
.
.
3. Select “On” or “Off” with
or
.
4. Press to exit the adjustment.
3-7. Setting Language “Language”
This function allows you to select a language for the Setting menu or displaying message.
Selectable languages
English/German/French/Spanish/Italian/Swedish/Japanese/Simplified Chinese/Traditional Chinese
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “Language” in the “Monitor Settings” menu, and press
The “Language” menu appears.
.
.
3. Choose a language with
or
.
4. Press to exit the adjustment.
3-8. Changing the HDCP authentication setting for
HDMI signal input
The external device cannot be authenticated successfully according to your external device and the screen
cannot be displayed. In this case, follow the procedures below to change the HDCP from the normal to extended
state.
Procedure
1. Press
2. Press
on the remote control or on the monitor to turn OFF the monitor power.
on the monitor for five seconds or more.
The setting changes and the monitor power is turned on.
Note
• The current setting status can be identified based on the color used to display the input port or signal error.
Setting
Input port
Signal Error
Normal
HDMI1
HDMI1
Signal Error
Extended
HDMI1
HDMI1
Signal Error
Chapter3SettingMonitor
30
3-9. Resetting the Monitor to the Default Settings
There are two different Resets: Color Reset for only resetting the color adjustments to the default settings and
Full Reset for resetting all settings to the defaults.
Attention
• After resetting, you cannot undo the operation.
Note
To reset the color adjustments “Color Reset”
●
This function only resets the color adjustments for the currently selected mode to the default settings.
Procedure
1. Choose “Color” in the Setting menu, and press
2. Choose “Color Reset” in the “Color” menu, and press
3. Select “Yes” with or
4. Press
.
.
.
.
The color adjustments revert to the default settings.
To reset all adjustments to the default settings “Reset”
●
This function resets all adjustments to the default settings.
Attention
• The reset operation cannot return the HDCP authentication setting (“3-8. Changing the HDCP authentication setting
for HDMI signal input” (page 30)) to the default setting.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “Reset” in the “Monitor Settings” menu, and press
.
.
3. Select “Yes” with
4. Press
or
.
.
All adjustments revert to the default settings.
Chapter3SettingMonitor
31
Chapter 4 Power Saving Functions
4-1. Setting Power Saving “Power Save”
Monitor
●
This function allows you to specify whether to set the monitor into the power saving mode, depending on the
state of an external device connected to it. When the monitor has shifted to the power saving mode, the
images on the screen are not displayed.
Attention
• Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.
• Power consumption varies even when the stereo mini jack cable is connected.
Note
• The monitor changes to the power saving mode about 15 seconds after the signal input ceases to be detected.
Procedure
1. Choose “PowerManager” in the Setting menu, and press
.
2. Choose “Power Save” in the “PowerManager” menu, and press
The “Power Save” menu appears.
.
3. Select “Enable” or “Disable” with
4. Press to exit the adjustment.
or
.
Power Saving System
Analog Signal Input
This monitor complies with the VESA DPM standard.
PC Monitor
Power Indicator
On
Powersaving STAND-BY
Operating
Blue
Powersavingmode
Orange
mode
SUSPENDED
OFF
PowerOff
Powersavingmode
Orange
Digital Signal Input
When the external device connected is a PC
This monitor complies with the DVI DMPM standard.
PC
Monitor
Power Indicator
On
Operating
Blue
Powersavingmode
PowerOff
Powersavingmode
Powersavingmode
Orange
Orange
When the external device connected is not a PC
Ext. Device Monitor
Power Indicator
PowerOn
PowerOff
Operating
Blue
Powersavingmode
Orange
Chapter4PowerSavingFunctions
32
Attention
• When all the conditions below are met, the monitor does not change to the power saving mode even if “Power Save”
is set to “Enable”:
In these cases, reset the mute.
Exiting the power saving mode
If the monitor receives input, it automatically exits the power saving mode and returns to the normal display
mode.
Audio Output
●
This monitor allows you to turn off the audio output from the speakers/headphone at the power saving mode.
Procedure
1. Choose “Sound” in the Setting menu, and press
.
2. Choose “Power Save” in the “Sound” menu, and press
The “Power Save” menu appears.
.
3. Select “Sound On” or “Sound Off” with
or
.
4. Press
to exit the adjustment.
Attention
• No audio is output while the monitor is in the Power Saving mode, if the HDMI signal is input or the sound source is
of HDMI.
4-2. Setting Power Indicator “Power Indicator”
This function allows you to set the power indicator (blue) ON/OFF in the monitor ON condition.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
.
2. Choose “Power Indicator” in the “Monitor Settings” menu, and press
The “Power Indicator” menu appears.
.
3. Select “Enable” or “Disable” with
4. Press to exit the adjustment.
or
.
Chapter4PowerSavingFunctions
33
4-3. Enabling/Disabling Automatic Brightness
Adjustment “Auto EcoView”
The sensor on the front side of the monitor detects the environmental brightness to adjust the screen brightness
automatically and comfortably by using the Auto EcoView function.
Attention
• Be careful not to block the sensor on the lower side of the monitor when using the Auto EcoView function.
Procedure
1. Press
on the remote control.
The “EcoView” menu appears.
2. Select “On” or “Off” with
or
.
3. Press
to exit the adjustment.
Note
• As “Brightness” in the Setting menu is changed, the auto adjustment range for Auto EcoView is also changed.
4-4. Checking the power saving level
The EcoView menu allows you to check Power Reduction, CO2 Reduction, and Eco Performance Level. The
more indicators light up representing the Eco Performance Level, the higher the power saving level attained.
Indicator
Procedure
1. Press
on the remote control.
The “EcoView” menu appears.
4-5. Enabling/Disabling Auto Power-OFF “Off Timer
(min)”
This function allows you to set the time to power off the monitor automatically.
Adjustable range
Disable, 30, 60, 90, 120, 150, 180
Procedure
1. Press
on the remote control.
Each time you press
, the set time changes.
Chapter4PowerSavingFunctions
34
Canceling Off Timer
1. Press
until “Disable” appears.
Checking the remaining time
1. Press
when the Off Timer is set.
The time to turn off the power appears.
Extending the time of the Off Timer
1. Press
while the remaining time is displayed.
Each time you press
, the time is extended.
Chapter4PowerSavingFunctions
35
Chapter 5 Connecting Cables
5-1. Connecting Multiple External Devices
The product has multiple connections to external devices and allows you to switch to one of the connections for
display.
Attention
• Do not use dual link cables.
Connection examples
HDMIconnector
DVI-Dconnector
D-Sub
connector
Toext.device1
Digital
(HDMI)
Digital
(DVI)
Analog
Signalcable
(MD-C87option)
D-Submini
15-pinconnector
Toext.device2
Signalcable
(suppliedFD-C39)
DVIconnector
Toext.device3,4
HDMIcable*1
(Commerciallyavailableproduct)
HDMI
connector
or
DVIconnector
DVI-HDMIconvertercable
(Commerciallyavailableproduct)
*1UseaproductabletohandleHighSpeed.
To switch among input signals
●
Press
or
on the remote control to change the input signal.
When the signal is switched, the active input port name appears at the top right corner of the screen.
PC2(D-SUB)
Note
•
Chapter5ConnectingCables
36
Chapter 6 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer.
No picture
Problem
Possible cause and remedy
1. No picture
• Powerindicatordoesnotlight.
• Checkwhetherthepowercordisconnectedproperly.
• Turnthemainpowerswitchon.
• Press
monitor).
ontheremotecontrol(or onthe
• Turnoffthemainpower,andthenturnitonagaina
fewminuteslater.
• Powerindicatorislightingblue.
• Powerindicatorislightingorange.
• Increase“Brightness”,“Contrast”,or“Gain”inthe
• Checkwhetherthesignalcableisconnectedproperly.
• Checkwhethertheexternaldeviceisturnedon.
• Operatethemouseorkeyboard.
• Switchtheinputsignal.
• IfanexternaldeviceispluggedintotheHDMIport,
changetheHDCPauthenticationsetting.Poweroff
onceandthenpress
onthemonitorforfive
secondsormoretochangethesettingandthenturn
onthepoweragain.(see“3-8.ChangingtheHDCP
2. The message below appears.
Thismessageappearswhenthesignalisnotinput
correctlyevenwhenthemonitorfunctionsproperly.
Example:
• Themessageshowsthattheinputsignalisoutofthe
specifiedrange.
PC2(D-SUB)
Signal Error
• Whentheanalogsignal(D-Sub)/digitalsignal(DVI-D,
HDMI:PCsignal)isinput,takethemeasuresbelow:
CheckwhetherthePCisconfiguredtomeetthe
resolutionandverticalscanfrequencyrequirements
ofthemonitor(see“2-1.CompatibleResolutions/
-
RebootthePC.
-
-
Selectanappropriatedisplaymodeusingthe
graphicsboard’sutility.Refertothemanualofthe
graphicsboardfordetails.
Chapter6Troubleshooting
37
Imaging problems (for both digital and analog)
Problem
Possible cause and remedy
3. The screen is too bright or too dark.
• Use“Brightness”or“Contrast”intheSettingmenuto
adjustit.(TheLCDmonitorbacklighthasalimitedlife
span.Whenthescreenbecomesdarkorbeginsto
flicker,contactyourlocaldealer.)
• TurnontheAutoEcoViewfunction.Themonitor
detectstheenvironmentalbrightnesstoadjustthe
screenbrightnessautomatically.
4. Characters are blurred.
• CheckwhetherthePCisconfiguredtomeetthe
resolutionandverticalscanfrequencyrequirements
ofthemonitor(see“2-1.CompatibleResolutions/
• Use“Smoothing”intheSettingmenutoadjustit(see
5. Afterimages appear.
• AfterimagesareparticulartoLCDmonitors.Avoid
displayingthesameimageforalongtime.
• Usethescreensaverorpowersavefunctiontoavoid
displayingthesameimageforextendedperiodsof
time.
6. Green/red/blue/white dots or defective
dots remain on the screen.
• ThisisduetoLCDpanelcharacteristicsandisnota
failure.
7. Interference patterns or pressure marks
remain on the screen.
• Leavethemonitorwithawhiteorblackscreen.The
symptommaydisappear.
8. Noise appears on the screen.
• WhenenteringthesignalsofHDCPsystem,the
normalimagesmaynotbedisplayedimmediately.
9. The screen is whitish or blackish.
• Use“ColorSpace”ofthe“Screen”submenu(forthe
contrast“Contrast””(page18))intheSettingmenuto
adjustit.
Imaging problems (for digital only)
Problem
Possible cause and remedy
10. The color shown on the display is not
correct (for HDMI input).
• Changethecolorspaceofthevideosignalin“Screen”
-“ColorSpace”undertheSettingmenu.
11. The screen flashes (for HDMI input)
• Transmittablesignalsdifferonthecategoryofthe
HDMIcable.CheckwhetherthecablesupportHigh
Speed.
Chapter6Troubleshooting
38
Imaging problems (for analog only)
Problem
Possible cause and remedy
12. Display position is incorrect.
• Use“Position”intheSettingmenutocorrectthe
• Iftheproblempersists,usethegraphicsboard’sutility
ifavailabletochangethedisplayposition.
13. Vertical bars appear on the screen or a
part of the image is flickering.
14. Whole screen is flickering or blurring.
Chapter6Troubleshooting
39
Other problems
Problem
Possible cause and remedy
15. The “Smoothing” on the Setting menu
“Screen” cannot be selected.
• Youcannotchoose“smoothing”whenthescreenis
displayedinthefollowingresolutionsorsettings.
Theresolutionis1920×1080
ScreenSizeis“Normal”
-
-
16. The auto adjustment function does not
work.
• Thisfunctiondoesnotworkduringdigitalsignalinput.
• ThisfunctionisintendedforuseontheMacintosh
andonAT-compatiblePCrunningWindows.Itdoes
notworkproperlywhenanimageisdisplayedonly
onapartofthescreen(commandpromptwindow,for
example)orwhenablackbackground(wallpaper,etc.)
isinuse.
• Thisfunctiondoesnotworkcorrectlywithsome
graphicsboards.
17. No audio output.
• Checkwhetherthestereominijackcableisconnected
properly.
• Checkwhethervolumeissetto0.
• Checkthecurrentexternaldeviceandaudioplayback
softwaretoseewhethertheyareconfiguredcorrectly.
• IfHDMIinputisused,checkthecurrentexternal
deviceandthe“Source”settingintheSettingmenu
18. “ScreenManager Pro for LCD (DDC/CI)”
does not run.
• “ScreenManagerProforLCD(DDC/CI)”doesnotrun
whenaPCisconnectedtotheHDMIinput.
19. Will not change to the power saving mode
• Whenalltheconditionsbelowaremet,themonitor
doesnotchangetothepowersavingmodeevenif
“PowerSave”issetto“Enable”:
-
-
Inthesecases,resetthemute.
Chapter6Troubleshooting
40
Chapter 7 Reference
7-1. How to Attach the Optional Arm
An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web
site for the corresponding optional arm (or optional stand). http://www.eizo.com
Attention
• When attaching an arm or stand, follow the instructions of their user’s manual.
• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the
VESA standard. Use the M4 × 12 mm screws supplied with this product.
- Clearance between the screw holes: 100 mm × 100 mm
- Thickness of plate: 2.6 mm
- Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables.
• When using an arm or stand, attach it to meet the following tilt angles of the monitor.
- Up 45°, down 45° (horizontal display, and vertical display rotated 90 degrees clockwise)
• Connect the cables after attaching an arm or stand.
• The monitor and arm or stand are heavy. Dropping them may result in injury or equipment damage.
Procedure
Lay the LCD monitor on a soft cloth spread over on a stable surface with the
panel surface facing down.
1.
Remove the Stand base.
2.
Turn the fixing screws for the Stand base to detach it.
Attach the arm or stand to the monitor.
3.
Secure the monitor to the arm or stand using the screws specified in the user’s manual of the arm or stand.
Chapter7Reference
41
7-2. Attaching the Stand base
The once removed the Stand base can be attached to the monitor again with the following procedures.
Procedure
Lay the LCD monitor on a soft cloth spread over on a stable surface with the
panel surface facing down.
1.
Attach the Stand base.
2.
Hold the Stand base with the arrow “ ” facing upward, align the two holes (a) of the Stand base with the two
tabs (b) at the bottom of the monitor, and snap the tabs into the holes.
b
a
Turn the supplied screw in the “LOCK” direction to lock the Stand base.
3.
Tightenscrew,thenpressknobflat.
7-3. Displaying Monitor Information “Information”
This function allows you to display the model name, serial number, usage time, resolution, and input signal.
Procedure
1. Choose “Information” in the Setting menu, and press
The “Information” menu appears.
.
Attention
• The usage time is not always “0” when you purchase the monitor due to factory inspection.
Chapter7Reference
42
7-4. Specifications
LCDPanel
Size
23.0-inch(580mm)
Type
TFTcolorLCD,VA
Surfacetreatment
Surfacehardness
Viewingangles
DotPitch
Anti-GlareHardCoating
3H
Viewingangles:Horizontal178°,vertical178°(CR≥10)
0.2655mm
ResponseTime
Black-white-black:Approx.25ms
Gray-to-gray:Approx.7ms(Overdrivesetting:Enhanced)
Contrastratio
3000:1(whenContrastEnhancersettingis“On”10000:1)
HorizontalScan Analog
31-81kHz
Frequency
Digital
DVI
31-68kHz
HDMI
15-68kHz
VerticalScan
Frequency
Analog
Digital
55-76Hz(non-interlace)
DVI
59-61Hz(non-interlace)
(VGATEXT:69-71Hz)
HDMI
49-61Hz(VGATEXT:69-71Hz)
Applicablevideosignalformats
VGA/525i(480i)/525p(480p)/1125i(1080i)/750p(720p)/1125p(1080p):60Hz
625i(576i)/625p(576p)/1125i(1080i)/750p(720p)/1125p(1080p):50Hz
Applicableaudiosignalformats
Resolution
2chlinearPCM(32kHz/44.1kHz/48kHz)
1920Dots×1080Lines
Max.DotClock
148.5MHz
Max.DisplayColor
DisplayArea(H×V)
PowerSupply
Approx.16.77millioncolors(1064.33millioncolors/10bitLUT)
509.76mm×286.74mm(20.1inch×11.3inch)
100-120VAC±10%,50/60Hz0.75A
200-240VAC±10%,50/60Hz0.45A
Power
ScreenDisplayOn
45Worless(Speakerworking)
Consumption
43Worless(Speakernotworking)
Powersavingmode
1.0Worless(forD-Subsinglesignalinput,whenstereominijack
cableisnotconnected)
PowerOff
0.17Worless
MainPowerOff
0W
InputSignalConnector
D-Submini15-pin
DVI-Dconnector(ApplicabletoHDCP)
HDMITypeA*1×2
AnalogInputSignal(Sync)
AnalogInputSignal(Video)
DigitalSignalTransmission
Videosignalmemory(Max.)
Separate,TTL,positive/negative
Analog,Positive(0.7Vp-p/75Ω)
TMDS(SingleLink)
D-Subinput:45types,DVI-Dinput:10types,
HDMI1input:10types,HDMI2input:10types
AudioOutput
LineInput
Speakeroutput:0.5W+0.5W(8Ω,THD+N:1%orless)
Headphoneoutput:2mW+2mW
Inputimpedance:44kΩ(typ.)
Inputlevel:2.0Vrms(Max.)
Plug&Play
VESADDC2B/EDIDstructure1.3
*1HDMICEC(ormutualcontrol)isnotsupported.
Chapter7Reference
43
Dimensions
(Width)×
(Height)×
(Depth)
Mainunit
549mm(21.6inch)×403mm(15.9inch)×212mm(8.3inch)
Mainunit(withoutstand) 549mm(21.6inch)×393mm(15.5inch)×58mm(2.28inch)
Mass
Mainunit
Approx.6.9kg(15.2lbs)
Mainunit(withoutstand) Approx.6.1kg(13.4lbs)
Tilt:20°Up,-5°Down
Movablerange
Environmental Temperature
Conditions
Operating:5°Cto35°C(41°Fto95°F)
Transportation/Storage:-20°Cto60°C(-4°Fto140°F)
Humidity
Operating:20%to80%R.H.(nocondensation)
Transportation/Storage:10%to90%R.H.(nocondensation)
AirPressure
Operating:700to1,060hPa
Transportation/Storage:200to1,060hPa
Main Default Settings
ColorMode
D-Sub/DVI-Dinput:User1
HDMIinput:Game
OffTimer
Disable
ScreenSize
D-Sub/DVI-Dinput:Fullscreen
HDMI(PCsignal/HDsignal)input:Fullscreen
HDMI(SDsignal)input:Auto
AutoEcoView
Smoothing
On
3
SoundLevel
Sound-PowerSave
PowerManager-PowerSave
DDC/CI
0
SoundOff
Enable
Enable
Off
KeyLock
Logo
On
PowerIndicator
Language
Enable
English
Chapter7Reference
44
Outside Dimensions
Unit:mm(inch)
486(19.1)
171(6.7)
180(7.1)
549(21.6)
TILT
224.5(8.8)
100(3.9)
224.5(8.8)
5°
511.8(20.1)
18.6
(0.73)
214(8.4)
62
(2.44)
212(8.3)
216(8.5)
Accessories
CleaningKit
EIZO“ScreenCleaner”
MD-C87
Signalcable(D-Submini15-pin)
For the latest information about the accessories, refer to our web site.
Chapter7Reference
45
7-5. Glossary
Clock
The analog signal input monitor needs to reproduce a clock of the same frequency as the dot clock of the
graphics system in use, when the analog signal is converted to a digital signal for image display. This is
called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.
Color Space
Color space is a method to specify and express the color. There are YUV and RGB, etc. YUV expresses the
color by using the luminance (Y), the color difference of R (U) and the color difference of blue (V). RGB
does it by using the gradation of 3 colors of Red (R, Green (G) and Blue (B).
DDC/CI (Display Data Channel/Command Interface)
VESA provides the standardization for the interactive communication of the setting information, etc.
between a PC and the monitor.
DVI (Digital Visual Interface)
DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss.
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors.
One is a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and
analog signal inputs.
DVI DMPM (DVI Digital Monitor Power Management)
DVI DMPM is a digital interface power-saving function. The “Monitor ON (operating mode)” and “Active
Off (power-saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.
Gain
This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color by
the light passing through the panel color filter. Red, green and blue are the three primary colors. All the
colors on the screen are displayed by combining these three colors. The color tone can be changed by
adjusting the light intensity (volume) passing through each color’s filter.
Gamma
Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma
Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value produces a
high-contrast image.
HDCP (High-bandwidth Digital Content Protection)
Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc.
This helps to transmit the digital contents safely by coding the digital contents sent via the DVI or HDMI
connector on the output side and decoding them on the input side.
Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not
applicable to HDCP system.
Chapter7Reference
46
HDMI (High-Definition Multimedia Interface)
HDMI is a digital interface standard, developed for consumer electrical appliance or AV device. This
standard is issued on the basis of the DVI standard which is one of an interface specification for the
connection between a PC and a monitor. The projected image, sound and control signal without compressed
enable to be transmitted with one cable.
Overdrive
This technology enhances response speed by increasing the potential difference at the time of motion of
liquid-crystal pixels, and it is used for liquid-crystal TV sets and others in general. It provides clear-cut
three-dimensional display with little image lag, by improving response speed of the intermediate graduation
range that frequently appears in moving images.
Phase
Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment is
made to adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted
correctly.
Range Adjustment
Range adjustment controls the signal output levels to display every color gradation. It is recommended that
range adjustment be made before color adjustment.
Resolution
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This
monitor consists of 1920 horizontal pixels and 1080 vertical pixels. At a resolution of 1920 × 1080, all pixels
are illuminated as a full screen (1:1).
sRGB (Standard RGB)
International standard for color reproduction and color space among peripheral devices (such as monitors,
printers, digital cameras, scanners). As a form of simple color matching for the Internet, colors can be
displayed using tones close to those of the transmission and reception devices.
Temperature
Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. The
screen becomes reddish at a low temperature, and bluish at a high temperature, like the flame temperature.
5000K: Slightly reddish white
6500K: White referred to as daylight-balanced color
9300K: Slightly bluish white
TMDS (Transition Minimized Differential Signaling)
TMDS is one of the signal transmission methods for the digital interface.
Chapter7Reference
47
VESA DPM (Video Electronics Standards Association - Display Power
Management)
VESA specifications achieve increased energy efficiency for computer monitors. This involves
standardization of signals sent from the computer (graphics board).
DPM defines the status of signals transmitted between the computer and monitor.
7-6. Preset Timing
The following table shows factory preset analog signal timing:
Attention
• Display position may be deviated depending on the PC connected, which may require screen adjustment using Setting
menu.
• If a signal other than those listed in the table is input, adjust the screen using the Setting menu. However, screen display
may still be incorrect even after the adjustment.
• When interlace signals are used, the screen cannot be displayed correctly even after screen adjustment using the Setting
menu.
Frequency
Polarity
Applicable
Signals
Resolution
Dot Clock:
MHz
Horizontal:
kHz
Vertical: Hz Horizontal Vertical
640×480
720×400
640×480
800×600
800×600
1024×768
1024×768
1280×720
1280×960
1280×1024
1280×1024
1680×1050
1680×1050
1920×1080
VGA/CEA-861
VGATEXT
VESA
25.18
28.32
31.50
40.00
49.50
65.00
78.75
31.47
31.47
37.50
37.88
46.88
48.36
60.02
45.00
60.00
63.98
79.98
65.29
64.67
67.50
59.94
70.09
75.00
60.32
75.00
60.00
75.03
60.00
60.00
60.02
75.03
59.95
59.88
60.00
Negative
Negative
Negative
Positive
Positive
Negative
Positive
Positive
Positive
Positive
Positive
Negative
Positive
Positive
Negative
Positive
Negative
Positive
Positive
Negative
Positive
Positive
Positive
Positive
Positive
Positive
Negative
Positive
VESA
VESA
VESA
VESA
CEA-861
VESA
VESA
74.25
108.00
108.00
135.00
146.25
119.00
148.50
VESA
VESACVT
VESACVTRB
CEA-861
Chapter7Reference
48
Appendix
Trademark
VESA is a registered trademark or a trademark of the Video Electronics Standards Association in the United
States and other countries.
Windows, Windows Vista, Windows Media, SQL Server, and Xbox 360 are registered trademarks of Microsoft
Corporation in the United States and other countries.
Apple, Mac, Macintosh, iMac, eMac, Mac OS, MacBook, PowerBook, ColorSync, QuickTime, and iBook are
registered trademarks of Apple Inc.
Acrobat, Adobe, Adobe AIR, and Photoshop are registered trademarks of Adobe Systems Incorporated in the
United States and other countries.
PowerPC is a registered trademark of International Business Machines Corporation.
Pentium is a registered trademark of Intel Corporation in the United States and other countries.
AMD Athlon and AMD Opteron are trademarks of Advanced Micro Devices, Inc.
GRACoL and IDEAlliance are registered trademarks of International Digital Enterprise Alliance.
ColorVision, ColorVision Spyder2 are registered trademarks of DataColor Holding AG.
Spyder3 is a trademark of DataColor Holding AG.
Eye-One, ColorMunki, and X-Rite are registered trademarks or trademarks of X-Rite Incorporated.
TouchWare is a trademark of 3M Touch Systems, Inc.
NextWindow is a registered trademark of NextWindow Ltd.
RealPlayer is a registered trademark of RealNetworks, Inc.
NEC is a registered trademark of NEC Corporation. PC-9801 and PC-9821 are trademarks of NEC
Corporation.
PlayStation is a registered trademark of Sony Computer Entertainment Inc.
PSP and PS3 are trademarks of Sony Computer Entertainment Inc.
ENERGY STAR is a registered trademark of the United States Environmental Protection Agency in the United
States and other countries.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing, LLC in the United States and other countries.
EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiForce, RadiCS, RadiNET, Raptor, and
ScreenManager are registered trademarks of EIZO NANAO CORPORATION in Japan and other countries.
ColorNavigator, EIZO EasyPIX, EcoView NET, EIZO ScreenSlicer, i•Sound, Screen Administrator, and
UniColor Pro are trademarks of EIZO NANAO CORPORATION.
All other company and product names are trademarks or registered trademarks of their respective owners.
License
A round gothic bold bit map font designed by Ricoh is used for the characters displayed on this product.
ENERGY STAR
As an ENERGY STAR Partner, EIZO NANAO CORPORATION has determined that this
product meets the ENERGY STAR guidelines for energy efficiency.
Appendix
49
TCO
This product has acquired the TCO standard that relates to the safety, ergonomics, environment and so forth of
office equipment. For an overview of the TCO, refer to our web site.
FCC Declaration of Conformity
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZONANAOTECHNOLOGIESINC.
5710WarlandDrive,Cypress,CA90630
Phone:(562)431-5011
declare that the product
Tradename:EIZO
Model:FORISFS2331
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuant
toPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainst
harmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio
frequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful
interferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurin
aparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,
whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrectthe
interferencebyoneormoreofthefollowingmeasures.
* Reorientorrelocatethereceivingantenna.
* Increasetheseparationbetweentheequipmentandreceiver.
* Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
* Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
Changesormodi cationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe
user’sauthoritytooperatetheequipment.
Note
Usetheattachedspeci edcablebeloworEIZOsignalcablewiththismonitorsoastokeepinterference
withinthelimitsofaClassBdigitaldevice.
- ACCord
- ShieldedSignalCable(Enclosed)
Canadian Notice
ThisClassBdigitalapparatuscomplieswithCanadianICES-003.
CetappareilnumériquedeleclasseBestcomformeàlanormeNMB-003duCanada.
Appendix
50
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige
Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der
Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:
Der Standfuß muß den nachfolgenden Anforderungen entsprechen:
a)Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes vom Bildschirmgerät
und des spezifizierten Zubehörs besitzen. Das Gewicht des Bildschirmgerätes und des Zubehörs sind in der
zugehörenden Bedienungsanleitung angegeben.
b)Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der Bildschirmanzeige nicht höher
als die Augenhöhe eines Benutzers in sitzender Position ist.
c)Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart erfolgen, daß die Höhe der
Bildschirmmitte über dem Boden zwischen 135 – 150 cm beträgt.
d)Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max. vorwärts: 5°, min. nach
hinten ≥ 5°).
e)Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen (max. ±180°). Der maximale
Kraftaufwand dafür muß weniger als 100 N betragen.
f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.
g)Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt).
h)Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der normalen aufrechten Position
kippsicher sein.
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB2000 mit dem Videosignal, 1920 ×
1080, Digital Eingang und mindestens 60,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus
ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte
Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)
Übermäßiger Schalldruck von Ohrhörern bzw. Kopfhörern kann einen Hörverlust bewirken.
Eine Einstellung des Equalizers auf Maximalwerte erhöht die Ausgangsspannung am Ohrhörer- bzw.
Kopfhörerausgang und damit auch den Schalldruckpegel.
„Maschinenlärminformations-Verordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779“
[Begrenzung des maximalen Schalldruckpegels am Ohr]
Bildschirmgeräte: Größte Ausgangsspannung 150 mV
Appendix
51
LIMITED WARRANTY
LIMITED WARRANTY
EIZONANAOCORPORATION(hereinafterreferredtoas“EIZO”)anddistributorsauthorizedbyEIZO(hereinafter
referredtoasthe“Distributors”)warrant,subjecttoandinaccordancewiththetermsofthislimitedwarranty(hereinafter
referredtoasthe“Warranty”),totheoriginalpurchaser(hereinafterreferredtoasthe“Original Purchaser”)who
purchasedtheproductspeci edinthisdocument(hereinafterreferredtoasthe“Product”)fromEIZOorDistributors,
thatEIZOandDistributorsshall,attheirsolediscretion,eitherrepairorreplacetheProductatnochargeiftheOriginal
PurchaserbecomesawarewithintheWarrantyPeriod(de nedbelow)thattheProductmalfunctionsorisdamagedinthe
courseofnormaluseoftheProductinaccordancewiththedescriptionintheinstructionmanualattachedtotheProduct
(hereinafterreferredtoasthe“User’s Manual”).
TheperiodofthisWarrantyislimitedto(i)five(5)yearsfromthedateofpurchaseoftheProduct;or,limitedtothe
expirationof(ii)30,000hoursofitsuseoftheProduct(hereinafterreferredtoasthe“WarrantyPeriod”);provided,
however,thattheWarrantyPeriodfortheLCDpaneloftheProductislimitedtothree(3)yearsfromthedateofpurchase
oftheProduct.EIZOandDistributorsshallbearnoliabilityorobligationwithregardtotheProductinrelationtothe
OriginalPurchaseroranythirdpartiesotherthanasprovidedunderthisWarranty.
EIZOandDistributorswillceasetoholdorstoreanypartsoftheProductuponexpirationofseven(7)yearsafterthe
productionofsuchpartsisdiscontinued.Inrepairingthemonitor,EIZOandDistributorswilluserenewalpartswhich
complywithourQCstandards.
TheWarrantyisvalidonlyinthecountriesorterritorieswheretheDistributorsarelocated.TheWarrantydoesnotrestrict
anylegalrightsoftheOriginalPurchaser.
NotwithstandinganyotherprovisionofthisWarranty,EIZOandDistributorsshallhavenoobligationunderthisWarranty
whatsoeverinanyofthecasesassetforthbelow:
(a) AnydefectoftheProductcausedbyfreightdamage,modi cation,alteration,abuse,misuse,accident,incorrect
installation,disaster,faultymaintenanceand/orimproperrepairbythirdpartyotherthanEIZOandDistributors;
(b) AnyincompatibilityoftheProductduetopossibletechnicalinnovationsand/orregulations;
(c) AnydeteriorationofdisplayperformancecausedbythedeteriorationofexpendablepartssuchastheLCDpanel
and/orbacklight,etc.(e.g.changesinbrightness,changesinbrightnessuniformity,changesincolor,changesin
coloruniformity,defectsinpixelsincludingburntpixels,etc.);
(d) AnydefectoftheProductcausedbyexternalequipment;
(e) AnydefectoftheProductonwhichtheoriginalserialnumberhasbeenalteredorremoved;
(f) AnydefectoftheProductcausedbyliquidleakingfrombattery;
(g) Anynormaldeteriorationoftheproduct,particularlythatofconsumables,accessories,and/orattachments(e.g.
batteries,buttons,rotatingparts,remotecontrol,cables,User’sManual,etc.);and
(h) Anydeformation,discoloration,and/orwarpoftheexterioroftheproductincludingthatofthesurfaceoftheLCD
panel.
ToobtainserviceundertheWarranty,theOriginalPurchasermustdelivertheProduct,freightprepaid,initsoriginal
packageorotheradequatepackageaffordinganequaldegreeofprotection,assumingtheriskofdamageand/orloss
intransit,tothelocalDistributor.TheOriginalPurchasermustpresentproofofpurchaseoftheProductandthedateof
suchpurchasewhenrequestingservicesundertheWarranty.
TheWarrantyPeriodforanyreplacedand/orrepairedproductunderthisWarrantyshallexpireattheendoftheoriginal
WarrantyPeriod.
EIZOORDISTRIBUTORSARENOTRESPONSIBLEFORANYDAMAGETO,ORLOSSOF,DATAOROTHER
INFORMATIONSTOREDINANYMEDIAORANYPARTOFANYPRODUCTRETURNEDTOEIZOORDISTRIBUTORS
FORREPAIR.
EIZOANDDISTRIBUTORSMAKENOFURTHERWARRANTIES,EXPRESSEDORIMPLIED,WITHRESPECTTO
THEPRODUCTANDITSQUALITY,PERFORMANCE,MERCHANTABILITYORFITNESSFORANYPARTICULAR
USE.INNOEVENTSHALLEIZOORDISTRIBUTORSBELIABLEFORANYINCIDENTAL,INDIRECT,SPECIAL,
CONSEQUENTIALOROTHERDAMAGEWHATSOEVER(INCLUDING,WITHOUTLIMITATION,DAMAGESFOR
LOSSOFPROFIT,BUSINESSINTERRUPTION,LOSSOFBUSINESSINFORMATION,ORANYOTHERPECUNIARY
LOSS)ARISINGOUTOFTHEUSEORINABILITYTOUSETHEPRODUCTORINANYCONNECTIONWITHTHE
PRODUCT,WHETHERBASEDONCONTRACT,TORT,NEGLIGENCE,STRICTLIABILITYOROTHERWISE,EVEN
IFEIZOORDISTRIBUTORSHAVEBEENADVISEDOFTHEPOSSIBILITYOFSUCHDAMAGES.THISEXCLUSION
ALSOINCLUDESANYLIABILITYWHICHMAYARISEOUTOFTHIRDPARTYCLAIMSAGAINSTTHEORIGINAL
PURCHASER.THEESSENCEOFTHISPROVISIONISTOLIMITTHEPOTENTIALLIABILITYOFEIZOAND
DISTRIBUTORSARISINGOUTOFTHISLIMITEDWARRANTYAND/ORSALES.
Appendix
52
BEGRENZTE GARANTIE
EIZONANAOCORPORATION(imWeiterenals„EIZO“bezeichnet)unddieVertragsimporteurevonEIZO(imWeiteren
als„Vertrieb(e)“bezeichnet)garantierendemursprünglichenKäufer(imWeiterenals„Erstkäufer“bezeichnet),der
dasindiesemDokumentvorgegebeneProdukt(imWeiterenals„Produkt“bezeichnet)vonEIZOodereinemVertrieb
erworbenhat,gemäßdenBedingungendieserbeschränktenGarantie(imWeiterenals„Garantie“bezeichnet),dass
EIZOundderVertriebnacheigenemErmessendasProduktentwederkostenlosreparierenoderaustauschen,falls
derErstkäuferinnerhalbderGarantiefrist(weiteruntenfestgelegt)eineFehlfunktionbzw.BeschädigungdesProdukts
feststellt,diewährenddesnormalenGebrauchsdesProduktsgemäßdenAnweisungendeszumLieferumfangdes
ProduktsgehörendenBenutzerhandbuchs(imWeiterenals„Benutzerhandbuch“bezeichnet)aufgetretenist.
DieDauerderGarantieleistungbeträgt(i)fünf(5)JahreabdemErstverkaufsdatumdesProduktsoder(ii)30.000
BetriebsstundendesProdukts(imWeiterenals„Garantiefrist“bezeichnet);dieGarantiefristfürdasLCD-Paneldes
Produktsistjedochaufdrei(3)JahreabdemErstverkaufsdatumdesProduktsbeschränkt.EIZOunddieVertriebe
übernehmenüberdenRahmendieserGarantiehinaushinsichtlichdesProduktskeinerleiHaftungoderVerp ichtung
demErstkäuferoderDrittengegenüber.
EIZOunddieVertriebeverp ichtensich,ErsatzteilefürdasProduktübereinenZeitraumvonsieben(7)Jahrennach
EinstellungderProduktionderErsatzteilezulagernbzw.anzubieten.EIZOundseineVertriebspartnerverp ichtensich,
beieineretwaigenReparaturdesMonitorsausschließlichProduktegemäßdenEIZO-Qualitätssicherungsstandardszu
verwenden.
Diese Garantie gilt nur in Ländern oder Gebieten, in denen sich Vertriebe befinden. Die gesetzlichen
GewährleistungsrechtedesErstkäufersgegenüberdemVerkäuferwerdendurchdieseGarantienichtberührt.
EIZOunddieVertriebebesitzenimRahmendieserGarantiekeinerleiVerp ichtungindenfolgendenFällen:
(a) Produktdefekte,dieaufFrachtschäden,Modifikation,Nachgestaltung,Missbrauch,Fehlbedienung,Unfälle,
unsachgemäßeInstallation,Naturkatastrophen,fehlerhafteWartungund/oderunsachgemäßeReparaturdurcheine
andereParteialsEIZOunddieVertriebezurückzuführensind.
(b) EineInkompatibilitätdesProduktsaufgrundvontechnischenNeuerungenund/oderneuenBestimmungen,die
nachdemKaufinKrafttreten.
(c) JeglicheVerschlechterungderBildschirmleistung,diedurchVerschleißteilewiedasLCD-Panelund/oderdie
Hintergrundbeleuchtungusw.hervorgerufenwerden(z.B.VeränderungenvonHelligkeitoderHelligkeitsverteilung,
VeränderungenvonFarbeoderFarbverteilung,PixeldefekteeinschließlichvondurchgebranntenPixelnusw.).
(d) Produktdefekte,diedurchexterneGeräteverursachtwerden.
(e) JeglicherDefekteinesProdukts,dessenursprünglicheSeriennummergeändertoderentferntwurde.
(f) Produktdefekte,diedurchAustrittvonBatterie üssigkeitverursachtwerden.
(g) NormaleAbnutzungdesProdukts,insbesonderevonVerbrauchsteilen,Zubehörteilenund/oderBeilagen(z.B.
Batterien,Tasten,drehbareTeile,Fernbedienung,Kabel,Benutzerhandbuchusw.);sowie
(h) Verformungen,Verfärbungenund/oderVerziehungenamProduktäußeren,einschließlichderOber ächedesLCD-
Panels.
BeiInanspruchnahmederGarantieleistungistderErstkäuferverpflichtet,dasProduktaufeigeneKostenund
inderOriginalverpackungbzw.eineranderengeeignetenVerpackung,dieeinengleichwertigenSchutzgegen
Transportschädenbietet,andenörtlichenVertriebzuübersenden,wobeiderErstkäuferdasTransportrisikogegenüber
Schädenund/oderVerlustträgt.ZumZeitpunktderInanspruchnahmederGarantieleistungmussderErstkäufereinen
Verkaufsbelegvorweisen,aufdemdasKaufdatumangegebenist.
DieGarantiefristfüreinimRahmendieserGarantieausgetauschtesund/oderrepariertesProdukterlischtnachAblauf
derursprünglichenGarantiefrist.
EIZOODERDIEEIZO-VERTRAGSIMPORTEUREHAFTENNICHTFÜRZERSTÖRTEDATENBESTÄNDEODERDIE
KOSTENDERWIEDERBESCHAFFUNGDIESERDATENBESTÄNDEAUFJEGLICHENDATENTRÄGERNODER
TEILENDESPRODUKTS,DIEIMRAHMENDERGARANTIEBEIEIZOODERDENEIZO-VERTRAGSIMPORTEUREN
ZURREPARATUREINGEREICHTWURDEN.
EIZOUNDDIEEIZO-VERTRAGSIMPORTEUREGEBENWEDEREXPLIZITENOCHIMPLIZITEGARANTIEN
INBEZUGAUFDIESESPRODUKTUNDSEINEQUALITÄT,LEISTUNG,VERKÄUFLICHKEITODEREIGNUNG
FÜREINENBESTIMMTENZWECK.AUFKEINENFALLSINDEIZOODERDIEEIZO-VERTRAGSIMPORTEURE
VERANTWORTLICHFÜRJEGLICHEZUFÄLLIGE,INDIREKTE,SPEZIELLE,FOLGE-ODERANDERESCHÄDEN
JEGLICHERART(EINSCHLIESSLICHOHNEJEDEBEGRENZUNGSCHÄDENBEZÜGLICHPROFITVERLUST,
GESCHÄFTSUNTERBRECHUNG,VERLUSTVONGESCHÄFTSINFORMATIONODERJEGLICHEANDEREN
FINANZIELLENEINBUSSEN),DIEDURCHDIEVERWENDUNGDESPRODUKTESODERDIEUNFÄHIGKEIT
ZURVERWENDUNGDESPRODUKTESODERINJEGLICHERBEZIEHUNGMITDEMPRODUKT,SEIES
BASIERENDAUFVERTRAG,SCHADENSERSATZ,NACHLAESSIGKEIT,STRIKTEHAFTPFLICHTODERANDEREN
FORDERUNGENENTSTEHEN,AUCHWENNEIZOUNDDIEEIZO-VERTRAGSIMPORTEUREIMVORAUSÜBER
DIEMÖGLICHKEITSOLCHERSCHÄDENINFORMIERTWURDEN.DIESERAUSSCHLUSSENTHÄLTAUCHJEDE
HAFTPFLICHT,DIEAUSFORDERUNGENDRITTERGEGENDENERSTKÄUFERENTSTEHENKANN.ZWECK
DIESERKLAUSELISTES,DIEHAFTUNGVONEIZOUNDDENVERTRIEBENGEGENÜBERFORDERUNGENZU
BEGRENZEN,DIEAUSDIESERBESCHRÄNKTENGARANTIEUND/ODERDEMVERKAUFENTSTEHENKÖNNEN.
Appendix
53
GARANTIE LIMITÉE
EIZONANAOCORPORATION(ci-aprèsdénommé«EIZO »)etlesdistributeursautorisésparEIZO(ci-aprèsdénommés
«Distributeurs »),sousréserveetconformémentauxtermesdecettegarantielimitée(ci-aprèsdénommée«Garantie
»),garantissentàl’acheteurinitial(ci-aprèsdénommé«Acheteur initial »)duproduitspéci édanslaprésente(ci-après
dénommé«Produit »)achetéauprèsd’EIZOoudeDistributeursagréésEIZO,queEIZOetsesDistributeursauront
pouroptionderéparerouremplacergratuitementleProduitsil’Acheteurinitialconstate,pendantlaPériodedegarantie
(dé nieci-dessous),qu’ilyaundysfonctionnementouqueleProduitasubiundommagedanslecadred’uneutilisation
normaleduProduitconformémentàladescriptiondumoded’emploiquiaccompagneleProduit(ci-aprèsdénommé«
Manuel d’utilisation »).
LapériodedecetteGarantieestlimitéeà(i)cinq(5)ansàpartirdeladated’achatduProduitouà(ii)30000heures
d’utilisationduProduit(ci-aprèsdénommée«Période de Garantie »),sousréserve,toutefois,quelaPériodede
GarantiedupanneauLCDduProduitestlimitéeàtrois(3)ansàpartirdeladated’achatduProduit.EIZOetses
DistributeursdéclinenttouteresponsabilitéouobligationconcernantceProduitfaceàl’Acheteurinitialouàtouteautre
personneàl’exceptiondecellesstipuléesdanslaprésenteGarantie.
EIZOetsesDistributeurscesserontdetenirouconserverenstocktoutepiècedeceProduitaprèsl’expirationde
lapériodedesept(7)anssuivantl’arrêtdelaproductiondetellespièces.Pourréparerlemoniteur,EIZOetses
distributeursutiliserontdespiècesderechangeconformesànosnormesdecontrôlequalité.
LaGarantieestvalableuniquementdanslespaysoulesterritoiresoùsetrouventlesDistributeurs.LaGarantienelimite
aucundesdroitsreconnusparlaloiàl’Acheteurinitial.
NonobstanttouteautreclausedecetteGarantie,EIZOetsesDistributeursn’aurontd’obligationdanslecadredecette
Garantiepouraucundescasénumérésci-dessous:
(a) ToutdéfautduProduitrésultantdedommagesoccasionnéslorsdutransport,d’unemodi cation,d’unealtération,
d’unabus,d’unemauvaiseutilisation,d’unaccident,d’uneinstallationincorrecte,d’undésastre,d’unentretienet/
oud’uneréparationincorrectseffectuésparunepersonneautrequeEIZOousesDistributeurs;
(b) TouteincompatibilitéduProduitrésultantd’améliorationstechniqueset/ouréglementationspossibles;
(c) Toutedétériorationdesperformancesd’affichagecauséeparladétériorationdesélémentsconsommablestels
quelepanneauLCDet/oulerétroéclairage,etc.(parexempledeschangementsdeluminosité,deschangements
del’uniformitédelaluminosité,desmodi cationsdecouleur,deschangementsdel’uniformitédescouleurs,des
défectuositésdepixelsycomprisdespixelsbrûlés,etc.);
(d) ToutdéfautduProduitcauséparunappareilexterne;
(e) Toutdéfautd’unProduitsurlequellenumérodesérieoriginalaétéaltéréousupprimé;
(f) ToutdéfautduProduitcauséparunécoulementduliquidecontenudanslespiles;
(g) ToutedétériorationnormaleduProduit,particulièrementcelledesconsommables,desaccessoireset/oudes
piècesreliéesauProduit(piles,touches,élémentspivotants,télécommande,câbles,Manueld’utilisationetc.),et
(h) Toutedéformation,décoloration,et/ougondolagedel’extérieurduProduit,ycompriscelledelasurfacedu
panneauLCD.
Pourbéné cierd’unservicedanslecadredecetteGarantie,l’AcheteurinitialdoitrenvoyerleProduitportpayé,dans
sonemballaged’origineoutoutautreemballageappropriéoffrantundegrédeprotectionéquivalent,auDistributeurlocal,
etassumeralaresponsabilitédesdommageset/oupertepossibleslorsdutransport.L’Acheteurinitialdoitprésenterune
preuved’achatduProduitcomprenantsadated’achatpourbéné cierdeceservicedanslecadredelaGarantie.
LaPériodedegarantiepourtoutProduitremplacéet/ouréparédanslecadredecetteGarantieexpireraàla ndela
Périodedegarantieinitiale.
EIZOOUSESDISTRIBUTEURSNESAURAIENTÊTRETENUSRESPONSABLESDESDOMMAGESOUPERTESDE
DONNÉESOUD’AUTRESINFORMATIONSSTOCKÉESDANSUNMÉDIAQUELCONQUEOUUNEAUTREPARTIE
DUPRODUITRENVOYÉÀEIZOOUAUXDISTRIBUTEURSPOURRÉPARATION.
AUCUNEAUTREGARANTIE,EXPLICITEOUTACITE,N’ESTOFFERTEPAREIZOETSESDISTRIBUTEURS
CONCERNANTLEPRODUITETSESQUALITÉS,PERFORMANCES,QUALITÉMARCHANDEOUADAPTATION
ÀUNUSAGEPARTICULIER.ENAUCUNCAS,EIZOOUSESDISTRIBUTEURSNESERONTRESPONSABLES
DESDOMMAGESFORTUITS,INDIRECTS,SPÉCIAUX,INDUITS,OUDETOUTAUTREDOMMAGEQUEL
QU’ILSOIT(YCOMPRIS,SANSLIMITATION,LESDOMMAGESRÉSULTANTD’UNEPERTEDEPROFIT,D’UNE
INTERRUPTIOND’ACTIVITÉS,D’UNEPERTEDEDONNÉESCOMMERCIALES,OUDETOUTAUTREMANQUE
ÀGAGNER)RÉSULTANTDEL’UTILISATIONOUDEL’INCAPACITÉD’UTILISERLEPRODUITOUAYANTUN
RAPPORTQUELCONQUEAVECLEPRODUIT,QUECESOITSURLABASED’UNCONTRAT,D’UNTORT,D’UNE
NÉGLIGENCE,D’UNERESPONSABILITÉSTRICTEOUAUTRE,MÊMESIEIZOOUSESDISTRIBUTEURSONTÉTÉ
AVERTISDELAPOSSIBILITÉDETELSDOMMAGES.CETTELIMITATIONINCLUTAUSSITOUTERESPONSABILITÉ
QUIPOURRAITÊTRESOULEVÉELORSDESRÉCLAMATIONSD’UNTIERSCONTREL’ACHETEURINITIAL.
L’ESSENCEDECETTECLAUSEESTDELIMITERLARESPONSABILITÉPOTENTIELLEDEEIZOETDESES
DISTRIBUTEURSRÉSULTANTDECETTEGARANTIELIMITÉEET/OUDESVENTES.
Appendix
54
GARANTÍA LIMITADA
EIZONANAOCORPORATION(enlosucesivo“EIZO”)ysusdistribuidoresautorizados(enlosucesivolos
“Distribuidores”),conarregloydeconformidadconlostérminosdeestagarantíalimitada(enlosucesivola“Garantía”),
garantizanalcompradororiginal(enlosucesivoel“Comprador original”)quecompróelproductoespeci cadoeneste
documento(enlosucesivoel“Producto”)aEIZOoasusDistribuidores,queEIZOysusDistribuidores,asupropio
criterio,repararánosustituiránelProductodeformagratuitasielCompradororiginaldetectadentrodelperiododela
Garantía(indicadoposteriormente)queelProductonofuncionacorrectamenteoquesehaaveriadoduranteeluso
normaldelmismodeacuerdoconlasindicacionesdelmanualdeinstruccionessuministradoconelProducto(enlo
sucesivoel“Manual del usuario”).
ElperíododevalidezdeestaGarantíaestálimitadoa(i)cinco(5)añosapartirdelafechadecompradelProductoo
(ii)a30.000horasdeusodelProducto(enadelantedesignadocomoel“Periodo de Garantía”);conlaexclusión,no
obstante,dequeelperíododegarantíadelpanelLCDdelProductoestálimitadoatres(3)añosapartirdelafecha
decompradelProducto.EIZOysusDistribuidoresnotendránningunaresponsabilidadniobligaciónconrespectoal
ProductoparaconelCompradororiginalnicontercerosquenoseanlasestipuladasenlapresenteGarantía.
EIZOysusDistribuidoresnoestaránobligadosasuministrarcualquierrecambiodelProductounavezpasadossiete
(7)añosdesdequesedejedefabricarelmismo.Paralareparacióndelmonitor,EIZOylosdistribuidoresutilizarán
repuestosquecumplanconnuestrosestándaresdecontroldecalidad.
LaGarantíaesválidasóloenlospaísesyterritoriosdondeestánubicadoslosDistribuidores.LaGarantíanorestringe
ningúnderecholegaldelCompradororiginal.
ApesardelasestipulacionesdeestaGarantía,EIZOysusDistribuidoresnotendránobligaciónalgunabajoesta
Garantíaenningunodeloscasosexpuestosacontinuación:
(a) CualquierdefectodelProductocausadopordañoseneltransporte,modi cación,alteración,abuso,usoincorrecto,
accidente,instalaciónincorrecta,desastre,mantenimientoincorrectoy/oreparaciónindebidarealizadaporun
terceroquenoseaEIZOosusDistribuidores.
(b) CualquierincompatibilidaddelProductodebidaaposiblesinnovacionestécnicasy/oreglamentaciones.
(c) Cualquierdeterioroenelrendimientodelavisualizacióncausadoporfallosenlaspiezasconsumiblescomoel
panelLCDy/ola"Backlight",etc.(p.ej.cambiosdebrillo,cambiosdeuniformidaddelbrillo,cambiosdecolor,
cambiosdeuniformidaddelcolor,defectosdepíxeles,incluyendopíxelesmuertos,etc.).
(d) CualquierdefectodelProductocausadoporunequipoexterno.
(e) CualquierdefectodelProductoenelquehayasidoalteradooborradoelnúmerodeserieoriginal.
(f) CualquierdefectodelProductocasusadoporfugasdelíquidodelaspilas.
(g) CualquierdeterioronormaldelProducto,yenparticulardelaspiezasconsumibles,accesoriosydemás(p.ej.
pilas,botones,piezasgiratorias,mandoadistancia,cables,Manualdelusuario,etc.).
(h) Cualquierdeformación,decoloracióny/oalabeodelexteriordelProductoincluidalasuper ciedelpanelLCD.
ParaobtenerservicioenlostérminosdeestaGarantía,elProductodeberáserenviadoporelCompradororiginal,
asuDistribuidorlocal,coneltransportepreviamentepagado,enelembalajeoriginaluotroembalajeadecuadoque
ofrezcaelmismogradodeprotección,asumiendoelriesgodedañosy/opérdidadelProductoduranteeltransporte.El
CompradororiginaldeberápresentaruncomprobantedecompradelProductoenelquesere ejelafechadecompra
delmismocuandolosoliciteelserviciodeGarantía.
ElPeriododegarantíaparacualquierProductoreemplazadoy/oreparadoenlostérminosdeestaGarantíaexpiraráal
vencerelPeriododegarantíaoriginal.
EIZOOLOSDISTRIBUIDORESAUTORIZADOSDEEIZONOSERESPONSABILIZANDENINGÚNDAÑOO
PÉRDIDAQUEPUEDANSUFRIRLOSDATOSUOTRAINFORMACIÓNALMACENADAENCUALQUIERMEDIOO
CUALQUIERPARTEDECUALQUIERPRODUCTODEVUELTOAEIZOOALOSDISTRIBUIDORESDEEIZOPARA
SUREPARACIÓN.
EIZOYLOSDISTRIBUIDORESAUTORIZADOSDEEIZONOOFRECENNINGUNAOTRAGARANTÍA,IMPLÍCITA
NIEXPLÍCITA,CONRESPECTOALPRODUCTOYASUCALIDAD,RENDIMIENTO,COMERCIABILIDADE
IDONEIDADPARACUALQUIERUSOENPARTICULAR.ENNINGÚNCASOSERÁNEIZOOLOSDISTRIBUIDORES
AUTORIZADOSDEEIZORESPONSABLESDENINGÚNDAÑOEMERGENTE,INDIRECTO,ESPECIAL,INHERENTE
OCUALQUIERAQUESEA(INCLUYENDO,SINLIMITACIÓN,DAÑOSPORLUCROCESANTE,INTERRUPCIÓN
DELAACTIVIDADCOMERCIAL,PÉRDIDADEINFORMACIÓNCOMERCIALOCUALQUIEROTRAPÉRDIDA
PECUNIARIA)QUESEDERIVEDELUSOOIMPOSIBILIDADDEUSODELPRODUCTOOENRELACIÓNCONEL
PRODUCTO,YASEABASADOENCONTRATO,PORAGRAVIO,NEGLIGENCIA,ESTRICTARESPONSABILIDAD
OCUALQUIERAQUESEA,AUNCUANDOSEHAYAADVERTIDOAEIZOOALOSDISTRIBUIDORESDEEIZO
DELAPOSIBILIDADDETALESDAÑOS.ESTAEXCLUSIÓNTAMBIÉNABARCACUALQUIERRESPONSABILIDAD
QUEPUEDADERIVARSEDERECLAMACIONESHECHASPORUNTERCEROCONTRAELCOMPRADOR
ORIGINAL.LAESENCIADEESTAESTIPULACIÓNESLIMITARLARESPONSABILIDADPOTENCIALDEEIZOYLOS
DISTRIBUIDORESQUEPUDIERADERIVARSEDEESTAGARANTÍALIMITADAY/OVENTAS.
Appendix
55
GARANZIA LIMITATA
EIZONANAOCORPORATION(acuisifaràriferimentodaquiinpoicon“EIZO”)ediDistributoriautorizzatidaEIZO(a
cuisifaràriferimentodaquiinpoicon“Distributori”)garantiscono,secondoiterminidiquestagaranzialimitata(acuisi
faràriferimentodaquiinpoicon“Garanzia”)all’acquirenteoriginale(acuisifaràriferimentodaquiinpoicon“Acquirente
originale”)chehaacquistatoilprodottospecificatoinquestodocumento(acuisifaràriferimentodaquiinpoicon
“Prodotto”)daEIZOodaisuoiDistributori,cheEIZOeidistributori,alorodiscrezione,riparerannoosostituirannoil
Prodottosenzaaddebitosel’Acquirenteoriginaletrova,entroilperiododellaGaranzia(de nitosotto),cheilProdotto
malfunzionaesièdanneggiatonelcorsodelsuonormaleutilizzoosservandoleindicazionidelmanualediistruzioni
allegatoalProdotto(acuisifaràriferimentodaquiinpoicon“Manuale utente”).
LapresenteGaranziaèlimitatoa(i)cinque(5)anniapartiredalladatad'acquistodelProdotto;o,limitato(ii)allo
scaderedi30.000ored'utilizzodelProdotto(acuisifaràriferimentodaquiinpoicon“Periodo di Garanzia”);tenendo
peròpresentecheilPeriododigaranziadelpannelloLCDdelProdottoèlimitatoatre(3)annidalladatad'acquisto
delProdotto.EIZOeisuoiDistributorinonsiassumonoalcunaresponsabilitàenonhannoalcunobbligoriguardoal
Prodottoversol’AcquirenteoriginaleoterzidiversidaquellirelativiaquestaGaranzia.
EIZOeisuoiDistributoricesserannoditenereodiconservarequalsiasiricambiodelProdottoalloscaderedisette
(7)annidopochelaproduzioneditaliricambièstataterminata.Perlariparazionedelmonitor,EIZOeiDistributori
utilizzerannopartidiricambioconformiainostristandarddicontrollodellaqualità.
LaGaranziaèvalidasoltantoneipaesidovecisonoiDistributoriEIZO.LaGaranzianonlimitaalcundirittolegale
dell’Acquirenteoriginale.
IndipendentementedaqualsiasialtracondizionediquestaGaranzia,EIZOeisuoiDistributorinonavrannoalcunobbligo
derivantedaquestaGaranziainognunodeicasielencatidiseguito:
(a) QualsiasidifettodelProdottocausatodadanniditrasporto,modi che,alterazioni,abusi,usiimpropri,incidenti,
installazioneerrata,calamità,manutenzioneerratae/oriparazioniimproprieeseguitedaterzepartichenonsiano
EIZOoisuoiDistributori.
(b) QualsiasiincompatibilitàdelProdottodovutaapossibiliinnovazionitecnichee/onormative.
(c) Qualsiasideterioramentodelleprestazionidelloschermocausatodaldeterioramentodelleparticonsumabili,come
ilpannelloLCDe/olaretroilluminazione,ecc.(peresempio:icambiamentidiluminosità,cambiamentidiuniformità
dellaluminosità,icambiamentidicolore,icambiamentidiuniformitàdelcolore,idifettideipixel,inclusiipixel
bruciati,ecc.).
(d) QualsiasidifettodelProdottocausatodaapparecchiatureesterne.
(e) QualsiasidifettodelProdottoincuiilnumerodiserieoriginalesiastatoalteratoorimosso.
(f) QualsiasidifettodelProdottocausatodallafuoriuscitadiliquidodallepile.
(g) QualsiasinormaledeterioramentodelProdotto,inparticolarmodonellesuepartidiconsumo,accessori,e/o
attacchi(peresempio:pile,tasti,partirotanti,telecomando,cavi,Manualedell’utente,ecc.).
(h) Qualsiasitipodideformazione,scolorimento,e/odiinvolucroesternodelProdottoinclusalasuper ciedelpannello
LCD.
PerricevereassistenzatecnicaconquestaGaranzia,l’AcquirenteoriginaledeveinviareilProdotto,contrasporto
pre-pagato,nellasuaconfezioneoriginaleoaltraconfezioneadeguatachefornisceunlivelloanalogodiprotezione,
assumendosiilrischiodidannie/operditaintransito,alDistributorelocale.L’Acquirenteoriginaledevepresentarela
provadiacquistochestabilisceladatadiacquistodelProdottoquandorichiedeserviziosottoGaranzia.
IlPeriododigaranziaperqualsiasiProdottosostituitoe/oriparatosottoquestaGaranziascadealla nedelPeriododi
garanziaoriginale.
EIZOOISUOIDISTRIBUTORINONSONORESPONSABILIPERQUALSIASIDANNOOPERDITADIDATIOALTRE
INFORMAZIONIMEMORIZZATISUQUALSIASISUPPORTOOQUALSIASIPARTEDIQUALSIASIPRODOTTO
INVIATOAEIZOOISUOIDISTRIBUTORIPERRIPARAZIONI.
EIZOEISUOIDISTRIBUTORINONOFFRONOALCUNAGARANZIAADDIZIONALE,IMPLICITAOESPLICITA,
RIGUARDOILPRODOTTOELASUAQUALITÀ,PRESTAZIONI,VENDIBILITÀOAPPROPRIATEZZAPER
QUALSIASIUSOPARTICOLARE.INNESSUNCASOEIZOOIDISTRIBUTORIEIZOAUTORIZZATISARANNO
RESPONSABILIPERQUALSIASIDANNOACCIDENTALE,INDIRETTO,SPECIALE,CONSEGUENTEODI
QUALSIASIALTRANATURA(INCLUSI,SENZALIMITI,DANNIPERPERDITADIPROFITTI,INTERRUZIONEDELLE
ATTIVITÀ,PERDITADIINFORMAZIONID’AFFARIOQUALSIASIALTRAPERDITAPECUNIARIA)DERIVANTI
DALL’USOODALL’IMPOSSIBILITÀDIUSAREILPRODOTTOOINQUALSIASIRELAZIONEALPRODOTTO,
SIASUBASEDICONTRATTO,TORTO,NEGLIGENZA,STRETTARESPONSABILITÀOALTRIMENTI,ANCHE
SEEIZOOIDISTRIBUTORIEIZOAUTORIZZATISONOSTATIAVVERTITIDELLAPOSSIBILITÀDITALIDANNI.
QUESTAESCLUSIONEINCLUDEANCHEQUALSIASIRESPONSABILITÀCHEPOSSAINSORGEREDARECLAMI
DITERZICONTROL’ACQUIRENTEORIGINALE.L’ESSENZADIQUESTOPROVVEDIMENTOÈLIMITARELA
RESPONSABILITÀPOTENZIALEDIEIZOEDEIDISTRIBUTORIDERIVANTEDAQUESTAGARANZIALIMITATAE/O
DALLEVENDITE.
Appendix
56
BEGRÄNSAD GARANTI
EIZONANAOCORPORATION(nedankallat“EIZO”)ochEIZOsauktoriseradedistributörer(nedankallade
“Distributörer”)garanterarienlighetmedvillkorenidennabegränsadegaranti(nedankallad“Garantin”)den
ursprungligeköparen(nedankalladden“Ursprunglige köparen”)somköptedenidokumentetspeci ceradeprodukten
(nedankallad“Produkten”)frånEIZOellerDistributörer,attEIZOellerDistributörerenligtegetgott nnandekostnadsfritt
antingenrepareraellerbytautdendefektaProduktenomdenUrsprungligeköpareninomGarantiperioden(de nieras
nedan)upptäckerattProduktenfungerarfelaktigtellerskadasundernormalanvändningavProduktenienlighetmed
beskrivningenibruksanvisningen(nedankallad“Bruksanvisning”).
Giltighetsperiodenfördennagarantiärbegränsadtill(i)fem(5)årfråndatumetförProduktensinköpeller,omdetta
inträffartidigare,begränsattillutlöpandetav(ii)30000timmarsanvändningavProdukten(härikallad“Garantiperioden”).
GarantiperiodenförProduktensLCD-panelärdockbegränsadtilltre(3)årfråndatumetförProduktensinköp.EIZOoch
DistributörerskainteundernågravillkorhanågotannatansvaränvadsomangesidennagarantigällandeProdukteni
relationtilldenUrsprungligeköparenellertredjepart.
EIZOochDistributörerkommerattupphöramedlagerhållningavProduktensdelareftersju(7)årefterattproduktionen
avdessadelarupphört.NätskärmenreparerasanvänderEIZOochdistributörerreservdelarsomuppfyllervåra
kvalitetsstandarder.
GarantinärendastgiltigideländerdärdetfinnsDistributörer.GarantinbegränsarintenågraavdenUrsprunglige
köparenslagstadgaderättigheter.
OavsettandravillkoridennagarantiskainteEIZODistributörerundernågravillkorhanågotansvarinågotavdefall
sombeskrivsnedan:
(a) NärnågonbristfällighethosProduktenkanhärledastillatthauppståttvidfrakt,modifiering,ändring,felaktigt
handhavande,olycka,felaktiginstallation,katastrof,felaktigtunderhålloch/ellerfelaktigreparationutfördavtredje
partannanänEIZOochDistributörer.
(b) AllaformeravinkompatibilitethosProduktenpågrundavmöjligatekniskainnovationeroch/ellerbestämmelser.
(c) Alla försämringar av bildens prestanda beroende på förbrukningsdelar så som LCD-panel och/eller
bakgrundsbelysningetc.(t.ex.ändringariljusstyrka,jämnhetiljusstyrka,färg,färgjämnhet,defektapixlaroch/eller
fastlysandepixlaretc.).
(d) AlladefekterhosProduktensomorsakatsavexternutrustning.
(e) AlladefekterhosProduktenpåvilkendetursprungligaserienumretharändratselleravlägsnats.
(f) Allaproduktfelsomorsakasavvätskasomläckerfrånbatteriet.
(g) AllnormalförsämringavProdukten,specielltförbrukningsartiklar,tillbehöroch/elleryttredelar(t.ex.batterier,
knappar,roterandedelar,fjärrkontroll,kablar,Bruksanvisningenetc.).
(h) Varjedeformation,missfärgningoch/ellerskevhetavProduktensyttreinklusiveytanpåLCD-panelen.
FöratterhållaserviceunderdennagarantimåstedenUrsprungligeköparen(medhänseendetillriskenförskada
och/ellerförlustundertransport)levereraProduktentillnärmasteDistributörmedförebetaldfrakt,idessursprungliga
förpackningellerannanfullgodförpackningsomgerlikvärdigtskydd.DenUrsprungligeköparenmåstekunnavisa
inköpsbevisförProduktensomklargörProduktensinköpsdatumvidbegäranavgarantiservice.
Garantiperiodenförallautbyttaoch/ellerrepareradeprodukterunderdennagarantiskallupphöravidutgångenavden
ursprungligaGarantiperioden.
EIZOELLERDISTRIBUTÖRERÄRINTEANSVARIGAFÖRNÅGONFORMAVSKADAELLERFÖRLUSTAVDATA
ELLERANNANINFORMATIONSOMHARLAGRATSINÅGONFORMAVMEDIAELLERANNANDELAVNÅGON
PRODUKTSOMHARRETURNERATSTILLEIZOELLERDISTRIBUTÖRERFÖRREPARATION.
EIZOOCHDISTRIBUTÖRERNAGARANTERARINGET,UTTRYCKLIGENELLERUNDERFÖRSTÅTT,VAD
BETRÄFFARPRODUKTENOCHDESSKVALITET,PRESTANDA,SÄLJBARHETELLERLÄMPLIGHETFÖRNÅGON
FORMAVSPECIELLANVÄNDNING.UNDERINGAOMSTÄNDIGHETERSKALLEIZOELLERDISTRIBUTÖRERNA
HÅLLASANSVARIGAFÖRNÅGRASOMHELSTUNDERORDNADE,INDIREKTA,SPECIELLA,DÄRAVFÖLJANDE
ELLERÖVRIGASKADOR(INKLUSIVE,UTANBEGRÄNSNINGTILL,SKADORFÖRFÖRLUSTAVINKOMST,
AVBRUTENAFFÄRSRÖRELSE,FÖRLUSTAVAFFÄRSINFORMATIONELLERANNANSÄRSKILDFÖRLUST)SOM
UPPSTÅTTSOMETTRESULTATAVANVÄNDNINGELLEROFÖRMÅGAATTANVÄNDAPRODUKTENELLERI
NÅGONFORMAVANSLUTNINGTILLPRODUKTERNA,VARESIGDETTAGRUNDASPÅKONTRAKT,ÅTALBAR
HANDLING,FÖRSUMLIGHET,ANSVARSSKYLDIGHETELLERANNAT,ÄVENOMEIZOELLERDISTRIBUTÖRERNA
HARINFORMERATSBETRÄFFANDEMÖJLIGHETATTSÅDANASKADORFÖRELIGGER.DETTAUNDANTAG
OMFATTARÄVENALLFORMAVANSVARSSKYLDIGHETSOMKANUPPSTÅGENOMENTREDJEPARTSANSPRÅK
GENTEMOTDENURSPRUNGLIGEKÖPAREN.GRUNDBESTÅNDSDELENIBESTÄMMELSENÄRATTBEGRÄNSA
DETEVENTUELLAANSVARSTAGANDETFÖREIZOOCHDISTRIBUTÖRERNASOMKANUPPSTÅGENOMDENNA
BEGRÄNSADEGARANTIOCH/ELLERFÖRSÄLJNING.
Appendix
57
ΠΕΡΙΟΡΙΣΜΕΝΗ ΕΓΓΥΗΣΗ
ΗEIZONANAOCORPORATION(στοεξής«EIZO»)καιοιδιανομείςπουεξουσιοδοτείηEIZO(στοεξής«Διανομείς»)
παρέχουνεγγύηση,υποκείμενηκαισύμφωναμετουςόρουςτηςπαρούσαςπεριορισμένηςεγγύησης(στοεξής
«Εγγύηση»),στοναρχικόαγοραστή(στοεξής«Αρχικός Αγοραστής»)οοποίοςαγόρασετοπροϊόνπουκαθορίζεταιστο
παρόνέγγραφο(στοεξής«Προϊόν»)απότηνEIZOήτουςΔιανομείς,ηοποίαεξασφαλίζειότιηEIZOκαιοιΔιανομείς,
σύμφωναμετηδιακριτήευχέρειάτους,είτεθαεπισκευάσουνείτεθααντικαταστήσουντοΠροϊόνχωρίςχρέωσηεάνο
ΑρχικόςΑγοραστήςαντιληφθείεντόςτηςΠεριόδουΕγγύησης(ορίζεταικατωτέρω)ότιτοΠροϊόνδυσλειτουργείήέχει
υποστείβλάβηκατάτηδιάρκειακανονικήςχρήσηςτουΠροϊόντοςσύμφωναμετηνπεριγραφήστοεγχειρίδιοχρήσηςπου
συνοδεύειτοΠροϊόν(στοεξής«Εγχειρίδιο Χρήστη»).
ΗπερίοδοςτηςπαρούσαςΕγγύησηςείναι(i)πέντε(5)έτηαπότηνημερομηνίααγοράςτουΠροϊόντος,ή,στηλήξητων
(ii)30.000ωρώνχρήσηςτουΠροϊόντος(στοεξής«Περίοδος Εγγύησης»),μετηνπροϋπόθεση,ωστόσο,ότιηΠερίοδος
ΕγγύησηςγιατηνοθόνηLCDτουΠροϊόντοςπεριορίζεταισετρία(3)έτηαπότηνημερομηνίααγοράςτουΠροϊόντος.Η
EIZOκαιοιΔιανομείςδενφέρουνκαμίαευθύνηήυποχρέωσηόσοναφοράτοΠροϊόνσεσχέσημετονΑρχικόΑγοραστή
ήοποιοδήποτετρίτομέρος,ούτεάλληευθύνηδιαφορετικήαπόαυτήνπουπαρέχεταιστηνπαρούσαΕγγύηση.
ΗEIZOκαιοιΔιανομείςθαπαύσουνναδιατηρούνήνααποθηκεύουντυχόνεξαρτήματατουΠροϊόντοςκατόπιντηςλήξης
τωνεπτά(7)ετώνμετάτηδιακοπήτηςπαραγωγήςτέτοιωνεξαρτημάτων.Κατάτηνεπισκευήτηςοθόνης,ηEIZOκαιοι
ΔιανομείςθαχρησιμοποιήσουνανταλλακτικάεπισκευήςπουσυμμορφώνονταιμεταπρότυπάμαςγιατηΔιασφάλιση
Ποιότητας.
ΗΕγγύησηισχύειμόνοσεχώρεςήπεριοχέςόπουβρίσκονταιοιΔιανομείς.ΗΕγγύησηδενπεριορίζειοποιαδήποτε
νόμιμαδικαιώματατουΑρχικούΑγοραστή.
ΛαμβανομένηςυπόψηκάθεδιάταξηςτηςπαρούσαςΕγγύησης,ηEIZOκαιοιΔιανομείςδενθαέχουνκαμίααπολύτως
υποχρέωσησύμφωναμετηνπαρούσαΕγγύησησεοποιαδήποτεαπότιςπεριπτώσειςπουδιατυπώνονταικατωτέρω:
(α) ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόζημιάκατάτημεταφορά,τροποποίηση,αλλαγή,κατάχρηση,
λανθασμένηχρήση,ατύχημα,λανθασμένηεγκατάσταση,καταστροφή,εσφαλμένησυντήρησηή/καιλανθασμένη
επισκευήαπότρίτομέροςεκτόςτηςEIZOκαιτωνΔιανομέων,
(β) ΤυχόνασυμβατότητατουΠροϊόντοςλόγωπιθανώντεχνικώνκαινοτομιώνή/καικανονισμών,
(γ) Τυχόνεπιδείνωσητηςαπόδοσηςοθόνηςπουπροκαλείταιαπότηφθοράαναλώσιμωνεξαρτημάτωνόπως
τηςοθόνηςLCDή/καιτουφωτόςυποβάθρου,κτλ.(π.χ.αλλαγέςστηφωτεινότητα,αλλαγέςστηνομοιομορφία
φωτεινότητας,αλλαγέςστοχρώμα,αλλαγέςστηνομοιομορφίαχρώματος,ελαττώματασεpixelπεριλαμβανομένων
τωνκαμένωνpixel,κτλ.),
(δ) ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόεξωτερικόεξοπλισμό,
(ε) ΤυχόνελάττωματουΠροϊόντοςστοοποίοέχειτροποποιηθείήαφαιρεθείογνήσιοςαριθμόςσειράς,
(στ)ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόδιαρροήυγρούαπότηνμπαταρία,
(ζ) Τυχόν φυσιολογική φθορά του προϊόντος, ιδιαίτερα αυτής των αναλώσιµων, των αξεσουάρ ή/και των
προσαρτηµάτων(π.χ.μπαταρίες,κουµπιά,περιστρεφόµεναµέρη,τηλεχειριστήριο,καλώδια,ΕγχειρίδιοΧρήστη,
κτλ.),και
(η) Τυχόν παραμόρφωση, αποχρωματισμό ή/και διαστρέβλωση του εξωτερικού μέρους του προϊόντος,
περιλαμβανομένηςτηςεπιφάνειαςτηςοθόνηςLCD.
ΟΑρχικόςΑγοραστήςγιαναδικαιούταιυπηρεσίεςεπισκευήςσύμφωναμετηνΕγγύηση,θαπρέπειναπαραδώσειτο
Προϊόν,μεπληρωμέναταμεταφορικάέξοδα,στηναρχικήτουσυσκευασίαήσεάλληεπαρκήσυσκευασίαμεισότιμο
βαθμόπροστασίας,αναλαμβάνονταςτονκίνδυνοβλάβηςή/καιαπώλειαςκατάτημεταφορά,στοντοπικόΔιανομέα.Ο
ΑρχικόςΑγοραστήςότανζητάυπηρεσίεςεπισκευήςσύμφωναμετηνΕγγύηση,θαπρέπειναπροσκομίζειτηναπόδειξη
αγοράςτουΠροϊόντοςκαιτηνημερομηνίατηςαγοράς.
ΗΠερίοδοςΕγγύησηςγιαοποιοδήποτεαντικατεστημένοή/καιεπισκευασμένοπροϊόνσύμφωναμετηνπαρούσα
ΕγγύησηλήγειστοτέλοςτηςαρχικήςΠεριόδουΕγγύησης.
ΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΔΕΝΕΥΘΥΝΟΝΤΑΙΓΙΑΟΠΟΙΑΔΗΠΟΤΕΒΛΑΒΗΉΑΠΩΛΕΙΑΔΕΔΟΜΕΝΩΝΉΑΛΛΩΝ
ΠΛΗΡΟΦΟΡΙΩΝΠΟΥΑΠΟΘΗΚΕΥΟΝΤΑΙΣΕΟΠΟΙΟΔΗΠΟΤΕΜΕΣΟΉΟΠΟΙΟΔΗΠΟΤΕΑΛΛΟΜΕΡΟΣΣΕ
ΟΠΟΙΟΔΗΠΟΤΕΠΡΟΪΟΝΠΟΥΕΠΙΣΤΡΕΦΕΤΑΙΣΤΗΝEIZOΉΣΕΔΙΑΝΟΜΕΑΓΙΑΕΠΙΣΚΕΥΗ.
ΗEIZOΚΑΙΟΙΔΙΑΝΟΜΕΙΣΔΕΝΠΑΡΕΧΟΥΝΚΑΜΙΑΠΕΡΑΙΤΕΡΩΕΓΓΥΗΣΗ,ΡΗΤΗΉΣΥΝΕΠΑΓΟΜΕΝΗ,ΟΣΟΝ
ΑΦΟΡΑΤΟΠΡΟΪΟΝΚΑΙΤΗΝΠΟΙΟΤΗΤΑ,ΤΗΝΑΠΟΔΟΣΗ,ΤΗΝΕΜΠΟΡΕΥΣΙΜΟΤΗΤΑΉΤΗΝΚΑΤΑΛΛΗΛΟΤΗΤΑ
ΤΟΥΓΙΑΟΠΟΙΑΔΗΠΟΤΕΣΥΓΚΕΚΡΙΜΕΝΗΧΡΗΣΗ.ΣΕΚΑΜΙΑΠΕΡΙΠΤΩΣΗΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΔΕΝ
ΘΑΕΥΘΥΝΟΝΤΑΙΓΙΑΚΑΜΙΑΑΠΟΛΥΤΩΣΤΥΧΑΙΑ,ΕΜΜΕΣΗ,ΕΙΔΙΚΗ,ΣΥΝΕΠΑΓΟΜΕΝΗΉΑΛΛΗΒΛΑΒΗ
(ΠΕΡΙΛΑΜΒΑΝΟΜΕΝΩΝ,ΜΕΤΑΞΥΑΛΛΩΝ,ΒΛΑΒΩΝΉΑΠΩΛΕΙΑΣΚΕΡΔΩΝ,ΔΙΑΚΟΠΗΣΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝ
ΔΡΑΣΤΗΡΙΟΤΗΤΩΝ,ΑΠΩΛΕΙΑΣΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝΠΛΗΡΟΦΟΡΙΩΝΉΤΥΧΟΝΑΛΛΗΣΧΡΗΜΑΤΙΚΗΣΑΠΩΛΕΙΑΣ)
ΠΟΥΠΡΟΚΥΠΤΕΙΑΠΟΤΗΧΡΗΣΗΉΤΗΝΑΝΙΚΑΝΟΤΗΤΑΧΡΗΣΗΣΤΟΥΠΡΟΪΟΝΤΟΣΉΤΥΧΟΝΑΛΛΗΣΣΥΝΔΕΣΗΣ
ΜΕΤΟΠΡΟΪΟΝ,ΕΙΤΕΒΑΣΙΖΕΤΑΙΣΕΣΥΜΒΟΛΑΙΟ,ΒΛΑΒΗ,ΑΜΕΛΕΙΑ,ΑΥΣΤΗΡΗΕΥΘΥΝΗΉΕΙΔΑΛΛΩΣ,ΑΚΟΜΗ
ΚΙΕΑΝΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΕΝΗΜΕΡΩΘΟΥΝΓΙΑΤΗΝΠΙΘΑΝΟΤΗΤΑΤΕΤΟΙΩΝΖΗΜΙΩΝ.ΗΕΞΑΙΡΕΣΗΑΥΤΗ
ΠΕΡΙΛΑΜΒΑΝΕΙΕΠΙΣΗΣΟΠΟΙΑΔΗΠΟΤΕΕΥΘΥΝΗΕΝΔΕΧΕΤΑΙΝΑΠΡΟΚΥΨΕΙΑΠΟΑΞΙΩΣΕΙΣΤΡΙΤΟΥΜΕΡΟΥΣ
ΚΑΤΑΤΟΥΑΡΧΙΚΟΥΑΓΟΡΑΣΤΗ.ΗΟΥΣΙΑΤΟΥΟΡΟΥΑΥΤΟΥΕΙΝΑΙΝΑΠΕΡΙΟΡΙΣΕΙΤΗΝΠΙΘΑΝΗΕΥΘΥΝΗΤΗΣ
EIZOΚΑΙΤΩΝΔΙΑΝΟΜΕΩΝΠΟΥΠΡΟΚΥΠΤΕΙΑΠΟΤΗΝΠΑΡΟΥΣΑΕΓΓΥΗΣΗΉ/ΚΑΙΤΙΣΠΩΛΗΣΕΙΣ.
Appendix
58
ОГРАНИЧЕННАЯ ГАРАНТИЯ
EIZONANAOCORPORATION(называемаявдальнейшем“EIZO”)иавторизированныеEIZOдистрибуторы
(называемыевдальнейшем“Дистрибуторы”)гарантируют,всоответствиисусловиямиипунктамиэтой
ограниченнойгарантии(называемойвдальнейшем“Гарантия”),первичномупокупателю(называемомув
дальнейшем“Первоначальный покупатель”),которыйприобрелуEIZOилиДистрибуторовпродукт,указанный
вэтомдокументе(называемыйвдальнейшем“Продукт”),чтоEIZOилиДистрибуторынасвоеусмотрение
либобесплатноотремонтируют,либобесплатнозаменятПродукт,еслиПервоначальныйпокупательпризнает
впределахГарантийногосрока(определенногониже),чтоПродуктнеисправенилионповрежденпроцессе
нормальногоиспользованияпродуктавсоответствиисописаниемвинструкциипоэксплуатации,прилагаемойк
Продукту(называемойвдальнейшем“Руководство пользователя”).
Гарантийныйпериодограниченсроком(i)пять(5)летотдатыприобретенияПродукта,илиограниченсроком(ii)
30000часовиспользованияПродукта(называемыйвдальнейшем“Гарантийный период”),приусловии,что
ГарантийныйпериоддляпанелиЖКДограниченсрокомтри(3)годаотдатыприобретенияПродукта.EIZOи
ДистрибуторыненесутникакойответственностиинеберутобязательствотносительноПродуктапоотношениюк
Первоначальномупокупателюилипоотношениюклюбымтретьимсторонам,кромеобязательств,оговоренныхв
этойГарантии.
EIZOиДистрибуторыпрекратятхранениеилискладированиелюбыхдеталейПродуктапоистечениисеми(7)
летпослепрекращенияпроизводстватакихдеталей.ВслучаеремонтамонитораEIZOиДистрибьюторыбудут
использоватьзапчасти,которыесоответствуютнашимстандартамQC(контролькачества).
Гарантиядействительнатольковстранахилирегионах,гдерасположеныДистрибуторы.Гарантияне
ограничиваетникакиезаконныеправаПервоначальногопокупателя.
НесмотрянадругиеусловияэтойГарантииEIZOиДистрибуторыненесутникакихобязательствсогласноэтой
Гарантиивлюбомизперечисленныхнижеслучаев:
(а) ЛюбыедефектыПродукта,вызванныеповреждениямиприперевозке,модификацией,изменением,
неправильнымобращением,неправильнымиспользованием,авариями,неправильнойустановкой,
стихийнымибедствиями,неправильнымуходоми/илинеправильнымремонтомтретьейстороной,отличной
отEIZOилиДистрибуторов;
(б) ЛюбыенесовместимостиПродуктаиз-затехническихусовершенствованийи/илиизменениятехнических
норм;
(в) Любыеухудшенияработыдисплея,вызванныеизнашиваниемневосстановимыхчастей,такихкак
панельЖКДи/илиподсветкаит.д.(например,изменениевяркости,изменениевравномерностияркости,
изменениевцветности,изменениевравномерностицветности,изменениевпикселах,включаявыгоревшие
пикселыит.д.);
(г) ЛюбыедефектыПродукта,вызванныевнешнимоборудованием;
(д) ЛюбыедефектыПродукта,прикоторыхоригинальныйсерийныйномербылизмененилиудален;
(е) ЛюбыедефектыПродукта,вызванныепротеканиембатарейки;
(ж) Любые естественные ухудшения продукта, в частности, вызванные износом расходных частей,
принадлежностейи/илиприспособлений(например,батареек,кнопок,вращающихсячастей,пульта
дистанционногоуправления,кабелей,Руководствапользователяит.д.);и
(з) Любыедеформации,измененияцветаи/иликороблениявнешнейповерхностипродукта,включая
поверхностьпанелиЖКД.
ЧтобыполучитьтехническоеобслуживаниеврамкахГарантии,Первоначальныйпокупательдолжендоставить
ПродуктместномуДистрибутору,оплативперевозку,вегооригинальнойупаковкеиливдругойсоответствующей
упаковке,обеспечивающейравноценнуюстепеньзащиты,принимаявовниманиерискповрежденияи/илиутерю
притранспортировке.ПризапросетехническогообслуживанияврамкахГарантииПервоначальныйпокупатель
долженпредоставитьсвидетельствопокупкипродуктаидатыпокупки.
Гарантийныйпериоддлялюбогозамененногои/илиотремонтированногопродуктаврамкахГарантииистекаетв
концезавершениясрокадействияоригинальногоГарантийногопериода.
EIZOИЛИДИСТРИБУТОРЫНЕНЕСУТОТВЕТСТВЕННОСТИЗАЛЮБЫЕПОВРЕЖДЕНИЯИЛИУТЕРЮ
ДАННЫХИЛИДРУГОЙИНФОРМАЦИИ,ХРАНЯЩИХСЯНАКАКИХ-ЛИБОНОСИТЕЛЯХИНФОРМАЦИИИЛИНА
ЛЮБЫХДРУГИХЧАСТЯХПРОДУКТА,КОТОРЫЙВОЗВРАЩЕНEIZOИЛИДИСТРИБУТОРАМДЛЯРЕМОНТА.
EIZO И ДИСТРИБУТОРЫ НЕ ДАЮТ НИКАКОЙ ДАЛЬНЕЙШЕЙ ГАРАНТИИ, ВЫРАЖЕННОЙ ИЛИ
ПОДРАЗУМЕВАЕМОЙ,ОТНОСИТЕЛЬНОПРОДУКТАИЕГОКАЧЕСТВА,ТЕХНИЧЕСКИХХАРАКТЕРИСТИК,
ТОВАРНОСТИИЛИСООТВЕТСТВИЯДЛЯКАКОГО-ЛИБООПРЕДЕЛЕННОГОИСПОЛЬЗОВАНИЯ.НИПРИ
КАКИХУСЛОВИЯХEIZOИЛИДИСТРИБУТОРЫНЕНЕСУТОТВЕТСТВЕННОСТИЗАЛЮБОЙСЛУЧАЙНЫЙ,
КОСВЕННЫЙ,СПЕЦИАЛЬНЫЙ,ПОБОЧНЫЙИЛИИНОЙУЩЕРБ(ВКЛЮЧАЯ,БЕЗОГРАНИЧЕНИЙ,УЩЕРБИЗ-
ЗАНЕПОЛУЧЕННОЙПРИБЫЛИ,ПРЕРЫВАНИЯБИЗНЕСА,ПОТЕРИКОММЕРЧЕСКОЙИНФОРМАЦИИИЛИ
ЛЮБЫЕДРУГИЕФИНАНСОВЫЕПОТЕРИ),ВОЗНИКШИЙИЗ-ЗАИСПОЛЬЗОВАНИЯИЛИНЕВОЗМОЖНОСТИ
ИСПОЛЬЗОВАТЬПРОДУКТИЛИВЛЮБОЙДРУГОЙСВЯЗИСПРОДУКТОМ,ЛИБООСНОВАННЫЙНА
КОНТРАКТНЫХОТНОШЕНИЯХ,ГРАЖДАНСКИХПРАВОНАРУШЕНИЯХ,НЕБРЕЖНОСТИ,ПРИЧИНЕНИЯ
УЩЕРБА ТРЕТЬЕЙ СТОРОНЕ ИЛИ ЧЕМ-ЛИБО ЕЩЕ, ДАЖЕ ЕСЛИ EIZO ИЛИ ДИСТРИБУТОРЫ БЫЛИ
УВЕДОМЛЕНЫОВОЗМОЖНОСТИТАКОГОУЩЕРБА.ЭТОИСКЛЮЧЕНИЕТАКЖЕВКЛЮЧАЕТЛЮБЫЕ
ОБЯЗАТЕЛЬСТВА,КОТОРЫЕМОГУТВОЗНИКНУТЬВРЕЗУЛЬТАТЕТРЕБОВАНИЙТРЕТЬЕЙСТОРОНЫ
В ОТНОШЕНИИ ПЕРВОНАЧАЛЬНОГО ПОКУПАТЕЛЯ. СУЩЕСТВОМ ЭТОГО ПОЛОЖЕНИЯ ЯВЛЯЕТСЯ
ОГРАНИЧЕНИЕПОТЕНЦИАЛЬНОЙОТВЕТСТВЕННОСТИEIZOИДИСТРИБУТОРОВ,ВОЗНИКАЮЩЕЙИЗ-ЗА
ЭТОЙОГРАНИЧЕННОЙГАРАНТИИИ/ИЛИПРОДАЖ.
Appendix
59
有限责任保证书
EIZO NANAO 有限公司 以下简称 EIZO 和EIZO 授权的经销商 以下简称 经销商
”),
接受并依照本有限责任保证书
(
“
”)
(
“
以下简称 保证书 之条款 向从EIZO 和经销商购买本文中所规定产品 以下简称 产品 的原买方 以下称 原买方
”) ”) ”)
(
“
,
(
“
(
“
提供保证 在保证期内 规定如下 如果原买方发现按本产品所附使用说明书 以下简称 用户手册 所述方式正常使
), ”)
:
(
(
“
用本产品过程中 本产品出现故障或损坏 EIZO 和经销商根据其独自的判断免费修理或更换该产品
。
,
,
本保证期限定为(i) 自本产品购买之日起的五(5) 年期间或限定为到达 ii 使用本产品3 万小时的期限 以下简称 保证期限
( )
(
“
”),
但本产品的液晶显示屏 LCD 的保证期限定为自本产品购买之日起的三(3) 年期间 EIZO 和经销商将不向原买方或任何
(
第三方承担本保证书所规定之外的与本产品有关任何责任或义务
)
。
。
本产品的任何部件停产七(7) 年后 EIZO 和经销商将不再保留或保管任何这类部件 维修显示器时 EIZO 与经销商将使
,
用符合我方质量控制标准的替换零件
。
,
。
本保证书仅对于设有经销商的国家或地区有效 本保证书并不限定原买方的任何法律权利
。
。
无论本保证书的任何其他条款如何规定 对于任何下列情况之一 EIZO 和经销商将不承担本保证书规定责任
,
,
:
(a) 由于运输损害 改装 改动 滥用 误用 意外事故 错误安装 灾害 维护不善和/ 或由除EIZO 和经销商以外的
、
、
、
、
、
第三方进行不适当的修理造成本产品的任何故障
、
、
、
。
(b) 由于可能发生的技术变更和/ 或调整造成本产品的任何不兼容性
。
(c) 由于诸如液晶显示屏 LCD 和/ 或背灯等消耗品部件的老化造成的任何显示性能低劣 如亮度变化 亮度均一性变化
(
色彩变化 色彩均一性变化 如烧伤像素等像素缺陷
)
(
、
、
、
、
)。
(d) 因外部设备造成本产品的任何故障
。
(e) 因本产品的原序号被改变或消除造成本产品的任何故障
。
(f) 因电池液体泄漏造成本产品的任何故障
。
(g) 本产品的任何正常老化 尤其是消耗品 附件和/ 或附加装置 如电池 按钮 旋转部件 遥控器 电缆 用户手册等
,
、
(
、
、
、
、
、
)、
以及
(h) 本产品表面包括液晶显示屏 LCD 表面的任何变形 变色和/ 翘曲
。
(
)
、
为了获得本保证书规定的服务 原买方必须使用原包装或其他具有同等保护程度的适当包装将本产品运送到当地的经销商
,
,
并且预付运费 承担运输中的损坏和/ 或损失的风险 要求提供本保证书规定的服务时 原买方必须提交购买本产品和标
,
明此购买日期的证明
。
,
。
按本保证书规定进行了更换和/ 或修理的任何产品的保证期限 将在原保证期限结束时终止
,
。
在返回给EIZO 和经销商进行修理后 任何产品的任何媒体或任何部件中储存的数据或其他信息发生任何损坏或损失 对
,
,
此EIZO 和经销商将不承担责任
。
对于本产品及其质量 性能 可销售性以及对于特殊用途的适合性 EIZO 和经销商不提供其他任何明示或暗示的保证 因
、
、
,
。
使用本产品或无法使用本产品或因与本产品有任何关系 无论是否根据合同 而造成: 任何附带的 间接的 特殊的 随
(
之发生的或其他的损害 包括但不仅限于 利润损失 业务中断 业务信息丢失或其他任何金钱损失 以及侵权行为 过失
)
、
、
、
(
:
、
、
)
、
、
。
严格赔偿责任或其他责任 即使已经向EIZO 和经销商提出了发生这些损害的可能性 对此EIZO 和经销商概不承担责任
,
,
本免责条款还包括因第三方向原买方提出索赔而可能发生的任何责任 本条款的本质是限定由于本有限责任保证书和/ 或
销售本产品所发生的EIZO 和经销商的潜在责任
。
。
Appendix
60
China Measures for RoHS Compliance in ChinaRoHS
关于电子信息产品污染控制标识
本标识根据「电子信息产品污染控制管理办法」,适用于在中华人民共和国销售的电子信息产品。标识中央的
数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项,在自制造日起算的年限内,不会
产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。
•
有毒有害物质或元素的名称及含量
部件名称
有毒有害物质或元素
铅
(Pb)
×
汞
(Hg)
○
镉
(Cd)
○
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
印刷电路板
机箱
○
○
○
○
○
○
○
○
○
○
○
○
○
×
○
×
○
○
液晶显示器
其他
×
○
○
○:表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T 11363-2006规定的限量要求以下。
×:表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T 11363-2006规定的限量要求。
(企业可在此处,根据实际情況对上表中打“×” 的技术原因进行进一步说明)
Appendix
61
4th Edition-May, 2012
03V23307D1
Copyright © 2010-2012 EIZO NANAO CORPORATION All rights reserved.
(
U.M-FS2331)
|