Dual XIA5600 User Manual

XIA5600  
INSTALLATION/OWNERSꢀMANUAL  
2/1-ChannelꢀMobileꢀPowerꢀAmplifier  
XIA5600ꢀINSTALLATION  
ConnectionꢀDescriptions  
NOTE:ꢀBeꢀsureꢀtoꢀfollowꢀspecificꢀinstructionsꢀincludedꢀwithꢀyourꢀamplifierꢀinstallationꢀ  
kitꢀ(notꢀincludedꢀwithꢀthisꢀamplifier).ꢀTheꢀinformationꢀbelowꢀshouldꢀbeꢀusedꢀaꢀgeneralꢀ  
guidelineꢀonly.  
PowerꢀWireꢀ(+12V)  
• Disconnect negative battery terminal before proceeding. Consult a qualified  
technician for instructions if you are unsure.  
• Plan wire routing before cutting any wires to length. Begin by routing the power  
+12V wire from the battery to the amplifier location. Use a grommet when running  
wires through the firewall or metal openings. Avoid running the power wire near  
existing vehicle wiring to prevent induced noise from entering the audio system.  
• Use extreme caution when drilling holes to avoid damaging fuel lines or existing  
vehicle wiring.  
• The +12V wire MUST be fused within 18" of the battery for protection of the vehicle’s  
electrical system.  
GroundꢀWireꢀ(GND)  
• The amplifier ground wire should be as short as possible. Choose a clean unpainted  
section of metal or the vehicle chassis when attaching the ground connection.  
Be sure to clean the area of any dirt or grease.  
RemoteꢀTurn-onꢀWireꢀ(REM)  
• The remote turn-on wire connects to the head unit's amplifier turn-on lead or  
power antenna output.  
SpeakerꢀWires  
• Choose adequate gauge speaker wire depending on your exact amplifier/speaker  
combination. Be sure to observe polarity when connecting.  
• Do not ground any speaker wires or connect any speaker wires together.  
IlluminiteꢀCircuitꢀ(12VDCꢀOutputꢀ-ꢀforꢀDUALꢀilluminiteꢀspeakersꢀonly)  
• Use 18-gauge or larger wire for making the connections to the illuminite terminals  
of DUAL illuminite speakers ONLY. Be sure to observe polarity when connecting.  
• Do not ground any illuminite output wires or connect any illuminite wires together.  
InputꢀSignalꢀ  
• The amplifier's input signal connects to the head unit's low level (RCA) or high level  
(speaker wire) outputs.  
• Low level input signal deliver the best performance. If unavailable, use the high  
level inputs - when interfacing with factory head unit for instance.  
CAUTION  
• Do not use both low and high level inputs at the same time - connect only one or  
the other.  
3
XIA5600ꢀINSTALLATION  
ConnectionsꢀandꢀControls  
1
2
3
4
5
6
7
14  
13  
12  
11  
10  
9
8
Ground Connection  
Remote Connection  
Low Level Inputs  
High Level Inputs  
Input Level Control  
Crossover Frequency  
Crossover Mode Switch  
Bass Boost  
1
2
3
4
5
6
7
8
9
+12VDC Battery Connection  
Main Fuses  
10  
11  
12  
13  
14  
illuminite Fuse  
illuminite Outputs  
Speaker Connections  
LED Indicator  
4
XIA5600ꢀINSTALLATION  
TypicalꢀWireꢀRouting  
MainꢀPowerꢀConnections  
Connect +12V, GND and REM wires accordingly. A suitable fuse MUST be installed on the  
+12V lead within 18" of the battery for protection of the vehicle’s electrical system.  
FuseꢀRating  
Power/GroundꢀWireꢀSize  
When replacing fuses, make sure  
new fuse is the correct type and  
amperage. Using an incorrect fuse  
could damage the amplifier.  
For optimum performance, use only  
the wire size listed below or larger.  
Make sure to use the same size  
power and ground wire.  
Mainꢀfuse 30 amp ATO x 3  
Power/groundꢀꢀ4 gauge  
illuminiteꢀfuse 2 amp ATO x 1  
illuminiteꢀoutput 18 gauge  
5
XIA5600ꢀINSTALLATION  
OutputꢀConnections  
The lighting elements of DUAL illuminite speakers provide you with a unique custom  
touch to your vehicle. Dual’s patent pending illuminite LED system and control circuitry  
provides an extraordinary blue-hue illumination which allows great creative opportunities  
for the beginner and seasoned custom installer alike. DUAL XIA-series amplifiers provide  
a dedicated switched 12VDC output including independent fused protection (2 amp)  
specifically for use with illuminite speakers.  
DUAL illuminite speakers have two distinct sets of input terminals. The first is labeled  
audio input terminals and the second is labeled illuminite lighting inputs. The inputs are  
clearly marked with a label positioned directly above the terminal housing. The polarity  
(+ and -) indicators for each set of inputs also appear on these labels.  
1. Do not connect the amplifier speaker outputs or any audio source to the illuminite  
lighting inputs.  
2. Refer to the figures below for making the connections. Make sure to observe polarity  
as the illuminite circuitry will not operate when connected reverse polarity. Connect  
either red wire from the XIA amplifier illuminite outputs to the positive (+) illuminite input  
terminal and connect either black wire from the XIA amplifier illuminite outputs to the  
negative (-) illuminite input.  
Additionalꢀilluminiteꢀwiringꢀnotes:  
Several illuminite speakers can be connected to the 12VDC illuminite output at one time.  
Refer to the table below for the individual illuminite speaker current requirements.  
If you are unsure, consult a qualified professional or call DUAL technical assistance at  
1-866-382-5476 for further information.  
illuminiteꢀcurrentꢀ  
requirements  
(perꢀspeaker)  
XiNC112 - 55mA  
XiNC110 - 55mA  
XiNBP210 - 180mA  
XiNBP212 - 180mA  
XOBP12D - 130mA  
OUTPUT CONNECTOR  
(Plugs into amplifier)  
6
XIA5600ꢀINSTALLATION  
AmplifierꢀConnections  
2ꢀSpeakersꢀ(stereo)  
Subwooferꢀ(mono)  
SpeakerꢀConnections  
Connect speaker wires observing  
polarity. The minimum impedance  
load is 2 ohms stereo and 4 ohms  
bridged. Use of loads lower than  
these is not recommended and  
may cause amplifier damage.  
The XIA5600 can be wired for  
stereo, bridged or stereo/bridged  
simultaneous operation.  
TypicalꢀStereoꢀWiring  
TypicalꢀBridgedꢀWiring  
(2ꢀohmsꢀminimum)  
(4ꢀohmsꢀminimum)  
InputꢀSignalꢀConnections  
LowꢀLevelꢀInputꢀ(RCA)  
Low level (RCA) input signal is preferred for best performance. Typical trunk-mount  
amplifier installations require a 17-20 foot RCA cable. Most trucks and under-seat  
applications require a 6-9 foot RCA cable. Using twisted pair construction RCA cables will  
minimize noise.  
HighꢀLevelꢀInputꢀ(SpeakerꢀWire)  
High level inputs should only be used  
when RCA outputs are not available  
from the head unit. Connect the head  
unit speaker outputs to the high level  
input connector as shown below. The  
black wire (signal reference ground)  
may or may not require a connection  
to chassis ground - depending on your  
particular installation.  
CAUTION: Do not use both low and high  
level inputs at the same time - connect  
only one or the other.  
7
XIA5600ꢀOPERATION  
Configuration/Setup  
InputꢀlevelꢀControl The input level control (gain) is used to obtain the best  
possible match between the head unit audio output and  
the amplifier input. Begin by turning the input level control  
fully counterclockwise. Next, turn up the head unit volume  
control around 3/4 of the way up. Adjust the input level  
control clockwise until audible distortion is heard, then  
slightly counterclockwise to provide the best match.  
CrossoverꢀꢀMode The crossover is used to filter out frequencies above or  
below a certain point. Choose LPF when using the amplifier  
with subwoofers and FULL when using with coaxial-type  
speakers.  
NOTE:  
Choose FULL when using the amplifier in stereo/bridged  
simultaneous mode. In this mode, passive crossovers are  
required. Failure to use the correct passive components  
may damage the amplifier and/or speakers. Consult a  
qualified professional for recommendations.  
CrossoverꢀFrequencyꢀControl This control allows precise adjustment of the crossover  
frequency.  
BassꢀBoost This control provides additional boost @ 45Hz when used  
with subwoofers. Adjust this control with caution - as  
improper use can damage speakers!  
LEDꢀIndicator The LED indicator illuminates green during normal  
operation (POWER) and red when the amplifier detects a  
fault (PROTECT).  
8
XIA5600ꢀWARRANTY  
LimitedꢀOneꢀYearꢀWarrantyꢀ  
This warranty gives you specific legal rights.  
Whatꢀtoꢀdo?  
You may also have other rights which vary from  
state to state.  
1. Before you call for service, check the  
troubleshooting guide in your owner’s  
manual. A slight adjustment of any custom  
controls may save you a service call.  
Dual Electronics Corp. warrants this product to  
the original purchaser to be free from defects in  
material and workmanship for a period of one  
year from the date of the original purchase.  
2. If you require service during the warranty  
period, you must carefully pack the product  
(preferably in the original package) and ship  
it by prepaid transportation with a copy of the  
original receipt from the retailer to an  
authorized service center.  
Dual Electronics Corp. agrees, at our option,  
during the warranty period, to repair any defect  
in material or workmanship or to furnish an  
equal new, renewed or comparable product  
(whichever is deemed necessary) in exchange  
without charges, subject to verification of the  
defect or malfunction and proof of the date of  
purchase. Subsequent replacement products  
are warranted for the balance of the original  
warranty period.  
3. Please describe your problem in writing and  
include your name, a return UPS shipping  
address (P.O. Box not acceptable), and a  
daytime phone number with your shipment.  
4. For more information and for the location of  
the nearest authorized service center please  
contact us by one of the following methods:  
Whoꢀisꢀcovered?ꢀThis warranty is extended to  
the original retail purchaser for products  
purchased and used in the U.S.A.  
• Call us toll-free at 1-866-382-5476  
• E-mail us at [email protected]  
Whatꢀisꢀcovered?ꢀThis warranty covers all  
defects in material and workmanship in this  
product. The following are not covered:  
installation/removal costs, damage resulting  
from accident, misuse, abuse, neglect, product  
modification, improper installation, incorrect  
line voltage, unauthorized repair or failure to  
follow instructions supplied with the product,  
or damage occurring during return shipment of  
the product.  
Exclusion of Certain Damages: This warranty  
is exclusive and in lieu of any and all other  
warranties, expressed or implied, including  
without limitation the implied warranties of  
merchantability and fitness for a particular  
purpose and any obligation, liability, right,  
claim or remedy in contract or tort, whether  
or not arising from the company’s negligence,  
actual or imputed. No person or representative  
is authorized to assume for the company any  
other liability in connection with the sale of  
this product. In no event shall the company be  
liable for indirect, incidental or consequential  
damages.  
9
XIA5600ꢀOPERATION  
Specificationsꢀ  
CEA-2006 Power Standard Specifications  
(reference:ꢀ14.4VDCꢀ+/-0.2V,ꢀ20Hz~20kHz)  
Power Output: 200ꢀWattsꢀRMSꢀxꢀ2ꢀchannelsꢀatꢀ4ꢀohmsꢀandꢀ<ꢀ1%ꢀTHD+N  
Signal to noise ratio: 74dBAꢀ(reference:ꢀ1ꢀwattꢀintoꢀ4ꢀohms)  
Additional power output:  
250ꢀWattsꢀRMSꢀxꢀ2ꢀchannelsꢀatꢀ2ꢀohmsꢀandꢀ<ꢀ1%ꢀTHD+N  
500ꢀWattsꢀRMSꢀxꢀ1ꢀchannelꢀatꢀ4ꢀohmsꢀ(bridged)ꢀandꢀ<ꢀ1%ꢀTHD+N  
Dynamic power: 1000ꢀWattsꢀatꢀ4ꢀohmsꢀ(bridged)  
Speaker output impedance: 2~8ꢀohmsꢀ(stereo),ꢀ4~8ꢀohmsꢀ(bridged)  
illuminite output voltage: 12VDC  
illuminite output current:ꢀꢀ2ꢀampꢀ  
Low level input range: 200mV~6Vꢀ(10kꢀohms)  
High level input range: 2V~10Vꢀ(100ꢀohms)  
Bass boost: 0~12dBꢀ@ꢀ45Hz  
Crossover range: 40~400Hz  
Crossover slope: 24dB/octave  
Power supply: 11-16ꢀVDC,ꢀnegativeꢀground  
Fuses: 30ꢀampꢀATOꢀxꢀ3,ꢀ2ꢀampꢀATOꢀxꢀ1  
Amplifier dimensions: 18.5"ꢀxꢀ2.36"ꢀxꢀ9.96"ꢀ(WxHxD)  
(470ꢀxꢀ60ꢀxꢀ263ꢀmm)  
Typical installation dimensions: 19.5"ꢀxꢀ3.5"ꢀxꢀ11"ꢀ(WxHxD)  
(495ꢀxꢀ89ꢀxꢀ279ꢀmm)  
10  
XIA5600ꢀOPERATION  
Troubleshooting  
Problem  
Cause  
Action  
Unitꢀwillꢀnotꢀturnꢀon  
+12V wire not connected or incorrect voltage Check connections for proper voltage  
(noꢀpowerꢀLEDꢀindicator) REM wire not connected or incorrect voltage  
(11~16VDC)  
GND wire not connected  
Check connection to ground  
Replace fuse(s)  
Fuse(s) blown  
Unitꢀhasꢀpowerꢀ-ꢀLEDꢀisꢀ Speaker wires not connected  
Check connections at speakers  
Increase volume level at head unit  
greenꢀ(butꢀnoꢀsound)  
Volume turned all the way down  
One or more speaker wires touching each  
other or touching chassis ground  
Insulate all bare speaker wires from  
each other and chassis ground  
Speaker(s) defective or damaged  
Input signal not connected  
Check/replace speaker(s)  
Check high or low level inputs for  
proper connection  
Unitꢀblowsꢀfuse(s)  
Engineꢀnoise  
Incorrect fuse rating  
Use fuse(s) with correct rating  
Check for pinched wire  
+12V wire touching chassis ground  
Speaker(s) defective or damaged  
Bad ground connection  
Check/replace speaker(s)  
Make sure amplifier is grounded to  
clean bare metal  
Signal ground loop or RFI  
(radio frequency interference)  
Re-route RCA cables from existing  
high current wiring  
LEDꢀilluminatesꢀred  
(protectꢀmode)  
One or more speaker wires touching each  
other or touching chassis ground  
Insulate all bare speaker wires from  
each other and chassis ground  
Speaker(s) defective or damaged internally  
(shorted)  
Check/replace speaker(s)  
Speaker load less than 2 ohms (stereo)  
Speaker load less than 4 ohms (bridged)  
Adjust speaker load - amplifier will  
not operate at less than 4 ohms when  
bridged  
Distortedꢀaudioꢀoutput  
Lowꢀaudioꢀoutput  
Weakꢀbassꢀ  
Incorrect input signal type or input level too  
high  
Check connections and reduce/adjust  
input level  
Incorrect input signal type or input level  
too low  
Check connections and increase/  
adjust input level  
Speaker(s) are wired out of phase  
Check (+) and (-) speaker connections  
(Observe correct polarity)  
Noꢀilluminiteꢀoutputꢀ  
(noꢀlights)  
Fuse blown - illuminite output (+12VDC) wire Check or replace fuse  
touching ground  
Use 2 amp ATO fuse only  
illuminite (+) or (-) wires not connected  
Check connections at speakers  
illuminite connections wired wrong  
(reverse polarity)  
Reverse (+) and (-) connections  
(Observe correct polarity)  
illuminite speaker(s) defective or damaged  
Check/replace speaker(s)  
11  
Dual Electronics Corp.  
Toll Free: 1-866-382-5476  
©2006 Dual Electronics Corp.  
NSA0806-V01  

Blanco 157 080 User Manual
Canon 9139B001 User Manual
Carcomm Qtek 8310 User Manual
Crown Boiler CWI172 User Manual
Euro Pro NINJA MASTER PREP QB900QP 30 User Manual
Focal Polyglass 690 CVX User Manual
Franklin Industries, L L C FWC36 User Manual
Genz Benz SHUTTLE 6 2 STL6 2 User Manual
Hypertec 3111 User Manual
Iiyama Car Video System E2202WSV User Manual