MXD662B
INSTALLATION/OWNER'SꢀMANUAL
AM/FM/CD/MP3/WMA/USB/3.5mmꢀ
MarineꢀReceiverꢀwithꢀDetachableꢀFace
MXD662BꢀINSTALLATIONꢀ
WiringꢀDiagram
RCA Connections
Right Channel (Red)
Left Channel (White)
REAR
FRONT
SUBWOOFER
FRONT
SUB/W
L-CH
R-CH
REMOTE IN
Antenna
Connector
Steering Wheel Interface Input
(PAC SWI-PS required)
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The MXD662B uses one
10 amp ATM fuse located
beside the wiring connector.
3
MXD662BꢀOPERATIONꢀ
ControlꢀLocationsꢀ-ꢀReceiver
2
5
6
4
8
1
3
7
9
10
20
18
16
19
17
15
14
13
12 11
USB Port with Silicone Cover
11
12
13
14
15
16
17
18
Release
Mode
1
2
Auxiliary Input with Silicone Cover
Tune/Track Up
Tune/Track Down
Display
Power ( )/Select
Preset 1/Repeat
3
4
5
Preset 4/Play/Pause
Preset 2/Random
Band/ESC
EQ
6
7
Preset 5/Folder Down
Preset 3/Intro
Preset 6/Folder Up
Eject
Scan/PS
8
9
19 Mute
20
10
Audio/Menu
The MXD662B allows playback of your favorite MP3 and WMA files recorded on CD-R and
CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while
maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic
Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track
search - even while a song is currently playing!
4
MXD662BꢀOPERATION
ControlꢀLocationsꢀ-ꢀRemote
2
1
3
4
5
6
20
19
7
8
18
17
9
10
16
15
11
12
13
14
Mode
Preset 5/Folder Down
Local/Distance Tuning
Loudness
11
12
13
14
15
16
17
18
19
1
2
Power ( )/Select
Volume Up
3
Display
4
Audio/Menu
Mute
5
Tune/Track Up
Volume Down
Scan/PS
EQ
6
Preset 4/Play/Pause
Preset 1/Repeat
Band/ESC
7
8
Preset 3/Intro
Preset 2/Random
Preset 6/Folder Up
9
10
20 Tune/Track Down
5
MXD662BꢀOPERATION
GeneralꢀOperation
Press RELEASE and pull away from the left side to remove.
To re-install, insert right side of faceplate first then push
left side to secure.
FaceplateꢀRemoval
Remove trim ring and install supplied #1 x 7/32” Phillips
head screw through left side of mounting frame into faceplate.
Semi-Permanentꢀ
FaceplateꢀInstallation
Press
on. Inserting a disc will turn the unit on automatically. Press
and hold to turn the unit off.
or any other button (except eject) to turn the unit
PowerꢀOn/Off
ꢀ
Press MODE to select between AM/FM, CD player, auxiliary
input and USB. Modes of operation are indicated in the
display.
Mode
Note: CD mode will not appear unless a CD is inserted.
Insert 3.5 mm plug to connect your portable audio device.
AuxiliaryꢀInput
Volume
The steering wheel interface input located on the back of the
Adjust volume using rotary encoder (00-46).
Mute
Press MUTE to silence the audio. “MUTE” will flash in the
display. Press MUTE again to cancel.
PresetꢀEQꢀCurves
Press EQꢀto enter EQ setup menu, then use the rotary
encoder to select between POP, JAZZ, CLASSIC, BEAT, ROCK
and FLAT (default) equalization curves. Any adjustment to
the Bass or Treble settings automatically cancels the current
EQ curve (if one is selected).
Reset
Display
Press to RESET the unit upon initial installation or if
abnormal operation occurs. The reset button is located
behind the faceplate.
Press DISP to select between clock and different types of
information, such as radio frequency, CD track or MP3/USB
song information.
SetꢀtheꢀClock
With the unit on, press and hold DISP until the clock begins
to flash, then release. Press TUNE
to adjust the
nn
hours and TUNEꢀ
to adjust the minutes. Press DISP
ll
momentarily to save the selected time.
12/24-hourꢀClock
The clock will display 12-hour AM/PM time in USA frequency
:
spacing mode (PM 10 00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
6
MXD662BꢀOPERATION
GeneralꢀOperation
Press and hold AUDIO/MENU for more than 3 seconds to
access the setup menu, then press AUDIO/MENU to cycle
through menu options. When desired option appears in the
display, rotate the rotaryꢀencoder left/right to adjust or activate
the desired function. Press ESC to exit the menu at any time.
SetupꢀMenu
SetupꢀMenu
MenuꢀFunction
Options
Action
AutoꢀStationꢀ
Store
AUTO STORE
Press SELECT to seek and save 6 strong stations in the current band.
Note: This option only appears in Tuner mode.
Loudnessꢀ
Curve
LOUD OFF
LOUD ON
Disables the loudness function.
Enables the loudness function. Activating this feature will enhance the
bass and treble frequencies when listening to music at low volumes.
TunerꢀFrequencyꢀ
Spacing
FREQ USA
FREQ EUR
Programs unit to USA tuner spacing.
(200kHz for FM and 10kHz for AM)
Programs unit to European tuner spacing.
(50kHz for FM and 9kHz for AM)
Clockꢀ
CLK OFF
CLK ON
Programs unit to not display the clock when the power is off.
Programs unit to display the clock when the power is off.
Enables the front panel 3.5mm auxiliary input.
Disables the auxiliary input.
Display
Auxiliaryꢀ
Input
AUX ON
AUX OFF
BEEP OFF
BEEP ON
PRO-VOL #
BeepꢀConfirmation
Disables the confirmation beep.
Enables the confirmation beep.
Programmableꢀ
TurnꢀOnꢀVolume
Programs unit to turn on at a specific volume
(default is OFF).
Local/Distanceꢀ
Tuning
LOCAL OFF
LOCAL ON
Activates distance tuning.
Activates local tuning for strong station reception only.
Disables power on message.
PowerꢀonꢀMessage MSG OFF
MSG ON
Enables power on message to be displayed.
Scrollingꢀ
Option
SCROLL ONCE
Programs unit to scroll once, then show the first 10 characters on the
display.
SCROLL ON
SCROLL OFF
DIMMER HI
DIMMER MED
DIMMER LOW
DEMO OFF
Programs unit to scroll continuously.
Programs unit to show the first 10 characters on the display.
Programs unit to the brightest illumination level.
Programs unit to the middle illumination level.
Programs unit to the dimmest illumination level.
Disables the demonstration mode.
Illuminationꢀ
Dimmer
Demonstrationꢀ
Mode
DEMO ON
Enables the "FULL SPEED USB INPUT " message.
7
MXD662BꢀOPERATION
GeneralꢀOperation
Press ESC to exit any menu adjustment mode.
Escape
Press AUDIO/MENU momentarily to select between Volume
(default), Bass, Treble, Balance, Fader, Subwoofer and
Source Volume Level.
Audio
VOLUME
BASS
TREBLE
BALANCE
FADER
SUBWOOFER
SOURCE LEVEL
Press AUDIO/MENU until BASS appears, then press SELECTꢀ
to confirm. Rotate encoder left/right to adjust (-6 minimum /
+6 maximum).
Bass
Press AUDIO/MENU until TREBLE appears, then press
SELECTꢀto confirm. Rotate encoder left/right to adjust ( -6
minimum / +6 maximum).
Treble
Note:ꢀAny adjustment to the Bass or Treble settings
automatically cancels the current EQ curve (if one is
selected).
Note: Bass and Treble settings are retained for each mode
individually.
Press AUDIO/MENU until BAL appears, then press SELECTꢀ
to confirm. Rotate encoder left/right to adjust (BAL L 12-BAL
00-BAL R 12). BAL 00 represents equal balance.
Balance
Fader
Press AUDIO/MENU until FADER appears, then press
SELECTꢀto confirm. Rotate encoder left/right to adjust (FAD
F 12-FAD 00-FAD R 12). FAD 00 represents equal fader.
Press AUDIO/MENU until SUB-W appears, then press
SELECTꢀto confirm. Rotate encoder left/right to adjust (0-12).
Adjusting levels to 0 turns the subwoofer off.
Subwoofer
The source volume level control allows a gain adjustment
for each audio source: AM, FM, CD, AUX and USB. Set the
source volume level for each mode, depending on the
relative volume of each audio source.
SourceꢀVolumeꢀLevel
To set the source volume level, press AUDIO/MENU until
SRC LEVEL appears. After one second, the current mode
will appear on the display. Turn the rotary encoder to adjust
the audio level of the current source (-6 minimum/+6
maximum).
Note:ꢀOnly the current mode will be available for
adjustment. To adjust another mode of operation, press
MODE until the desired mode is selected, then set the
source volume level for that mode.
8
MXD662BꢀOPERATION
AM/FMꢀTunerꢀOperation
SeekꢀTuning Press TUNE
or TUNEꢀ
for more than one second to
nn
ll
seek the next strong station.
ManualꢀTuning Press TUNE
or TUNEꢀ
momentarily to move radio
nn
ll
frequency up or down one step at a time. Press and hold to
advance quickly.
ScanꢀTuning Press SCAN to preview strong stations on the current band,
pausing for five seconds at each. Press SCAN again to
cancel.
Bandꢀ Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
StoringꢀandꢀRecallingꢀ Up to 18 FM stations and 12 AM stations can be stored. To
StationꢀPresets store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
two seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
PresetꢀScan Press PS for more than two seconds to scan presets 1-6 on
the current band, pausing for five seconds at each. Press
PS again to cancel.
9
MXD662BꢀOPERATIONꢀ
CDꢀPlayerꢀOperation
With the label facing up, insert a standard size CD into the
CD slot. The CD will automatically begin playback.
InsertꢀCD
Press EJECT to eject the CD. The unit will change to
previous mode of operation (tuner, AUX or USB). If the disc
is not removed within 10 seconds, the unit will reload the
disc. The unit does not have to be turned on to eject CD.
EjectꢀCD
Press TRACKꢀ
to skip to the beginning of the next
TrackꢀSelect
ll
track. Press TRACK
to return to the beginning of the
nn
current track. Pressing TRACK
beginning of the previous track.
again skips to the
nn
Press and hold TRACKꢀ
or reverse a track.
or TRACK
to fast forward
FastꢀForwardꢀandꢀReverse
ll
nn
Press
Press
/
/
II to temporarily stop CD playback.
Pause
l
l
II again to resume playback.
Press RPTꢀto enter the Repeat menu, then turn the rotary
encoder to select one of the following options:
• OFF - Cancels the RPTꢀfunction.
Repeat
• TRACK - Continuously repeats selected track.
Press RDMꢀto enter the Random menu, then turn the rotary
encoder to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
Random
• ALL- Plays all tracks in random order.
Note: Random mode is retained in memory when selecting
between tuner, CD, AUX, and USB modes and when the unit
is turned on/off.
Press INTꢀto enter the Intro menu, then turn the rotary
encoder to select one of the following options:
• OFF - Cancels the INTꢀfunction.
Intro
• ALL - Plays the first 10 seconds of each track.
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method.
In addition, the following CDs may be incompatible with
this unit: CDs exposed to extreme temperatures or direct
sunlight for extended periods of time, CDs recorded in
which a recording session failed or a re-recording was
attempted and encrypted or copy-protected CDs that do not
conform to the audio CD-DA red book recording standard.
CD-R/CD-RWꢀCompatibility
10
MXD662BꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
PlayingꢀanꢀMP3/WMAꢀDisc
When an MP3/WMA encoded disc is first inserted,
“READING” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
DisplayingꢀInformation
Press DISP to select between track name (default), song
title, artist, track number or clock & elapsed time.
“NO ID3 TAG” will be displayed if the MP3 file contains no
ID3 tag information.
ꢀꢀ
“UNKNOWN” will be displayed if the WMA file contains no
WMA tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
ꢀTitleꢀIconꢀ
ArtistꢀIcon
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
This icon will illuminate when the folder name is displayed.
This icon will illuminate when the track name is displayed.
FolderꢀIconꢀ
TrackꢀIconꢀ
ꢀ
ꢀ
CharacterꢀSupport
Maximum character display information
• Track name – 32 character maximum
• Directory name – 23 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
*Song title and Artist Name will only be displayed if included
with the MP3/WMA file.
When referring to MP3/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name
11
MXD662BꢀOPERATIONꢀ
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
Folder/FileꢀSearchꢀMode
Press SELECT to enter the folder/file search mode. The head
unit will read the CD, and a list of folders and files from the
CD will be displayed, starting from the current directory.
Folder/FileꢀNavigation
Turn the rotary encoder to cycle through the list of folders
and files. The current selection will flash in the display.
Folders will be displayed first, followed by any files.
FOLDER 1
FOLDER 2
FILE 1
FILE 2
Etc . . .
• When a folder name is being displayed,
• When a file name is being displayed,
will illuminate.
will illuminate.
Press SELECT when a folder is displayed to change
directories and begin displaying the contents of that folder.
When searching the contents of a subfolder, select ". ." at the
top of the menu to go up one folder level.
NavigatingꢀNote
Press ESC from the root directory to exit search mode.
After navigating to desired file, the track name will be
displayed by default. Press DISP momentarily to cycle
through other display options:
TRACK NAME
TITLE
TRACK NUMBER
CLOCK & ELAPSED TIME
ARTIST
12
MXD662BꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
FolderꢀAccessꢀ
Press
Press
to select the previous folder.
to select the next folder.
Note:ꢀFolder access is only available on MP3/WMA discs
recorded with more than one folder.
Repeat
Press RPTꢀto enter the Repeat menu, then turn the rotary
encoder to select one of the following options:
• OFF - Cancels the RPTꢀfunction.
• TRACK - Continuously repeats selected track.
• FOLDER - Continuously repeats all files in selected folder.
Random
Press RDMꢀto enter the Random menu, then turn the rotary
encoder to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL- Plays all tracks in random order.
• FOLDER - Plays all tracks in folder in random order.
Note: Random mode is retained in memory when selecting
between tuner, CD, AUX and USB modes and when the unit
is turned on/off.
Intro
Press INTꢀto enter the Intro menu, then turn the rotary
encoder to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ALL - Plays first 10 seconds of each track.
• FOLDER - Plays first 10 seconds of each track in folder.
Note: Folder repeat, random and intro options only function
on MP3/WMA discs recorded with more than one folder.
13
MXD662BꢀOPERATIONꢀ
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
MediaꢀCompatibility
The following types of discs/files are compatible:
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA
• MP3 data
• WMA data
The following types of discs/files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• Discs recorded with Track At Once or packet writing
• MP3 PRO format
• MP3 playlists
• WAV format
PlaybackꢀOrder
MP3/WMA playback sequence is based on recorded order
of files and begins in the root folder of the disc. Any empty
folders or folders that do not include MP3/WMA files are
skipped. This unit may not play files in the order they were
recorded in. Refer to your recording software’s user’s
manual for more information.
CompatibleꢀRecordingꢀ
Formats
• ISO9660 level 1
• ISO9660 level 2
• Yellow Book MODE 1
• Yellow Book MODE 2 FORM 1
• Multi session
• Maximum folders and files - 256
• Maximum folder levels - 8
• MPEG-1/2/2.5 Audio Layer-3
ISO9660 standards:
• Maximum nested folder depth is 8 (including the root
folder).
• Valid characters for folder/file names are letters A-Z
(all caps), numbers 0-9, and “_” (underscore). Some
characters may not be displayed correctly, depending on
the character type.
• This device can play back discs in Joliet, Romeo, and other
standards that conform to ISO9660. MP3/WMA written in the
formats other than the above may not play and/or their file
names or folder names may not be displayed properly.
14
MXD662BꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
AdditionalꢀMP3/WMAꢀ
An internal buffer provides ESP (Electronic Skip Protection) to
virtually eliminate skipping.
Information
When playing a disc recorded with regular audio files
(CD-DA or .WAV) and MP3/WMA files, the unit will play the
MP3/WMA files only.
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be played.
Do not attempt to play discs which contain non-MP3/WMA
files with the MP3/WMA extension.
SamplingꢀFrequencyꢀRates
MP3
8kHz ~ 48kHz
32kHz ~ 48kHz
WMA
TransferꢀBitꢀrates
MP3
32kbps ~ 320kbps constant
Variable bit rates
WMA
32kbps ~ 192kbps constant
Variable bit rates
Note:
Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3ꢀTagꢀDisplay
ID3 tags Version 1.0 to 2.0
RecommendedꢀSettings
For best results, use the following settings when burning an
MP3 disc:
128kbps or higher constant bit rate
44.1kHz or higher sampling frequency
For best results, use the following settings when burning a
WMA disc:
64kbps or higher constant bit rate
32kHz or higher sampling frequency
15
MXD662BꢀOPERATION
USBꢀOperationꢀ-ꢀMP3/WMAꢀFilesꢀ(Optional)
Play MP3/WMA files from most mass storage devices by
connecting them to the MXD662B's USB port.
ConnectingꢀaꢀUSBꢀDevice
(soldꢀseparately)
When a USB device is first connected, press MODE to
access USB mode. “READING” will appear momentarily in
the display. Depending on the number of files and folders,
this may take several seconds. If no valid MP3/WMA files
are detected, “NO FILE” will be displayed and the last mode
will be resumed.
PlayingꢀMusic
Press TRACKꢀ
track. Press TRACK
current track. Pressing TRACK
beginning of the previous track.
to skip to the beginning of the next
TrackꢀSelect
ll
to return to the beginning of the
nn
again skips to the
nn
Press and hold TRACKꢀ
forward or reverse a track.
or TRACK
to fast
FastꢀForwardꢀandꢀReverse
Pause
ll
nn
Press
Press
/
/
II to temporarily stop USB playback.
II again to resume playback.
l
l
Press SELECTꢀmomentarily, and TRK * will appear in the
display. Turn the rotary encoder to select the desired track
number, then press SELECT to begin playback of selected
track.
DirectꢀFileꢀSelect
When a file is accessed, the clock and elapsed time will
be displayed. Press DISP momentarily to select file name
(default), song title, artist, track number or clock & elapsed
time.
DisplayingꢀInformation
TRACK NAME
TITLE
TRACK NUMBER
CLOCK & ELAPSED TIME
ARTIST
ꢀꢀ
"NO TITLE" will be displayed if no song title information is
available.
"NO ARTIST" will be displayed if no artist information is
available.
16
MXD662BꢀOPERATION
USBꢀOperationꢀ-ꢀMP3/WMAꢀFilesꢀ(Optional)
ꢀTitleꢀIconꢀ
ArtistꢀIcon
FolderꢀIconꢀ
TrackꢀIconꢀ
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
This icon will illuminate when the folder name is displayed.
This icon will illuminate when the track name is displayed.
ꢀ
ꢀ
Press
Press
to select the previous folder.
to select the next folder.
FolderꢀAccessꢀ
Note: Folder access is only available on USB devices with
more than one folder.
Repeat Press RPTꢀto enter the Repeat menu, then turn the rotary
encoder to select one of the following options:
• OFF - Cancels the RPTꢀfunction.
• TRACK - Continuously repeats selected track.
• FOLDER - Continuously repeats all files in selected folder.
Random
ꢀ
Press RDMꢀto enter the Random menu, then turn the rotary
encoder to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL- Plays all tracks in random order.
• FOLDER - Plays all tracks in folder in random order.
Note: Random mode is retained in memory when selecting
between tuner, CD, AUX and USB modes and when the unit
is turned on/off.
Intro
Press INTꢀto enter the Intro menu, then turn the rotary
encoder to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ALL - Plays first 10 seconds of each track.
• FOLDER - Plays first 10 seconds of each track in folder.
17
MXD662BꢀOPERATION
USBꢀOperationꢀ-ꢀMP3/WMAꢀFilesꢀ(Optional)
CharacterꢀSupport
Maximum character display information
• Track name – 32 character maximum
• Directory name – 32 character maximum
• *Song title – 32 character maximum
• *Artist name – 32 character maximum
*Song title and artist name will only be displayed if included
with the MP3/WMA file.
MediaꢀCompatibility
The following types of files are compatible:
• MP3 data
• WMA data
The following types of files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• MP3 PRO format
• MP3 playlists
• WAV format
PlaybackꢀOrder
MP3/WMA playback sequence is based on order the files are
copied to the USB device and begins in the root folder. Any
empty folders or folders that do not include MP3/WMA files
are skipped. Depending on your software, the playback order
may vary.
PlaybackꢀCapacity
• Maximum number of files: 48896
• Maximum number of folders: 127 plus the root directory
• Maximum number of files in each folder and root: 382
• Maximum number of folder levels (sub folders): 8
(7 levels plus the root)
Note: If the number of files/folders exceeds the maximum
outlined above, the additional files/folders will be ignored.
USBꢀDeviceꢀCompatibility
Due to the differences of USB devices, some devices may not
be compatible. USB devices must be ‘mass storage class’
and formatted to the FAT or FAT32 file system in order to
ensure compatibility.
18
MXD662BꢀOPERATION
USBꢀOperationꢀ-ꢀMP3/WMAꢀFilesꢀ(Optional)
AdditionalꢀMP3/WMAꢀ
Information
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be
played. Do not attempt to play non-MP3/WMA files with the
MP3/WMA extension.
SamplingꢀFrequencyꢀRates
MP3
8kHz ~ 48kHz
32kHz ~ 48kHz
WMA
TransferꢀBitꢀrates
MP3
32kbps ~ 320kbps constant
Variable bit rates
WMA
32kbps ~ 192kbps constant
Variable bit rates
Note: Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3ꢀTagꢀDisplay
USBꢀCharging
ID3 tags Version 1.0 to 2.0
Note: If an invalid ID3 tag version is detected, "NO
SUPPORT" will scroll on the display.
Charge a cell phone, portable MP3 player or other device
through the unit's USB port.
19
MXD662BꢀOPERATION
LimitedꢀOneꢀYearꢀWarranty
This warranty gives you specific legal rights.
You may also have other rights which vary from
state to state.
Whatꢀtoꢀdo?
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls may save you a service call.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
in material or workmanship or to furnish an
equal new, renewed or comparable product
(whichever is deemed necessary) in exchange
without charges, subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.
3. Please describe your problem in writing and
include your name, a return UPS shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.
4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:
Whoꢀisꢀcovered?ꢀThis warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A.
• Call us toll-free at 1-866-382-5476
• E-mail us at [email protected]
Whatꢀisꢀcovered?ꢀThis warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
line voltage, unauthorized repair or failure to
follow instructions supplied with the product,
or damage occurring during return shipment of
the product.
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect, incidental or consequential
damages.
20
MXD662BꢀOPERATION
Troubleshootingꢀ-ꢀGeneral
Problem
Cause
Action
Yellow wire not connected or incorrect voltage Check connections for proper
Unitꢀwillꢀnotꢀturnꢀonꢀ
(noꢀpower)
Red wire not connected or incorrect voltage
Black wire not connected
Fuse blown
voltage (11~16VDC)
Check connection to ground
Replace fuse
Speaker wires not connected
Check connections at speakers
Unitꢀhasꢀpowerꢀ
(butꢀnoꢀsound)
One or more speaker wires touching each
other or touching chassis ground
Insulate all bare speaker wires from
each other and chassis ground
Yellow or red wire touching chassis ground
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Check for pinched wire
Use fuse with correct rating
Unitꢀblowsꢀfuses
Unit is not mounted correctly or backstrap is
not secure
Check mounting sleeve and
backstrap support
Excessiveꢀskipping
Physical defect in media (CD, CD-R or CD-RW) Check media for scratches
ERROR-01ꢀappearsꢀ
onꢀdisplay
Disc read error
Press EJECT or RESET
ERROR-02ꢀappearsꢀ
onꢀdisplay
Focus error or disc is in upside down
Press EJECT or RESET
PROTECTꢀappearsꢀ
onꢀdisplay
The WMA file is copy-protected by DRM
(Digital Rights Management)
Write disc using WMA files that are
not copy-protected
NOꢀFILEꢀappearsꢀ
onꢀdisplay
Selected file is not available in direct or
alphanumeric search modes
Repeat search using valid
parameters
INVALIDꢀappearsꢀ
onꢀdisplay
The file format is incompatible
Write disc using valid audio files
with .mp3 or .wma file extensions
CD mechanism position out of alignment
CD transit screws still in place
Press and hold EJECT for 3 seconds
to reset CD mechanism position
Unitꢀwillꢀnotꢀacceptꢀ
aꢀdisc
Remove 2 transit screws located on
top of the unit
An invalid ID3 tag version is present
Version 1.0 to 2.0 ID3 tags are
supported.
NOꢀSUPPORTꢀappearsꢀonꢀ
display
21
MXD662BꢀOPERATION
Specifications
CDꢀPlayer Frequency response: 10Hz-20kHz
Channel separation @ 1kHz: >65dB
D/A converter: 1ꢀBit
FMꢀTuner Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AMꢀTuner Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
General Operating voltage: 11-16ꢀVDC,ꢀnegativeꢀground
Speaker output impedance: 4~8ꢀohms
Line output voltage: 2ꢀVoltsꢀRMS
Dimensions: 7"ꢀxꢀ7"ꢀxꢀ2"ꢀ(178ꢀxꢀ178ꢀxꢀ51ꢀmm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 17 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
22
MXD662BꢀOPERATION
Notes
23
Dual Electronics Corp.
Toll Free: 1-866-382-5476
©2008 Dual Electronics Corp. All rights reserved.
Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the
United States and or other countries. Other trademarks and trade names are those of their respective owners.
NSA0708-V01
|