XDMA5280
INSTALLATION/OWNER'SꢀMANUAL
AM/FM/CDꢀReceiverꢀwithꢀDetachableꢀFace
XDMA5280ꢀINSTALLATIONꢀ
WiringꢀDiagram
Rear Preamp Output
Connect to amplifier RCA input
RCA Cable
(sold separately)
Antenna Connector
BLUE Remote Turn-On
Connect to amplifier or power
AMP
antenna. Insulate wire if not used.
BLACK Ground
Connect to vehicle
chassis ground.
RED Accessory
Connect to ignition
circuit or switched 12 volt source.
10 AMP
AGC Fuse
YELLOW Memory
FUSE
Connect to battery
circuit or constant 12 volt source.
When replacing the
fuse, make sure new
fuse is the correct type
and amperage. Using
an incorrect fuse could
damage the radio.
Right Front
Gray/Black (-)
Gray (+)
Right Rear
Violet/Black (-)
Violet (+)
The XDMA5280 uses
one 10 amp ATM fuse
located beside the wiring
connector.
Left Front
White/Black (-)
White (+)
Left Rear
Green/Black (-)
Green (+)
3
XDMA5280ꢀOPERATION
ControlꢀLocationsꢀ-ꢀReceiver
1
2
3
4
5
6
7
8
18
17
16
15 14 13 12 11 10
9
Preset 6 / Folder Up
Preset 5 / Folder Down
Preset 4 / Play / Pause
Preset 3/ Intro
1
2
3
4
5
6
7
8
9
Release
10
11
12
13
14
15
16
17
18
Volume
Mute / Power
Tune / Track Down
Source
Preset 2 / Random
Preset 1 / Repeat
Band / Select
Tune / Track Up
Eject
Display / Escape
Audio / Menu
USB Port
Auxiliary Input
4
XDMA5280ꢀOPERATION
ControlꢀLocationsꢀ-ꢀRemote
5
6
4
3
2
1
7
8
9
1
2
3
4
5
Display/ESC
Tune/Track Down
Band/Select
Mute/Power
Volume Up
6
7
8
9
Source
Tune/Track Up
Volume Down
Audio/Menu
5
XDMA5280ꢀOPERATION
GeneralꢀOperation
Press or any other button (except EJECT) to turn the unit
PowerꢀOn/Off
on. Press to turn the unit off.
Press SOURCEꢀto select between AM/FM, CD player,
auxiliary input, USB and operation of iPod®/iPhone®. Modes
of operation are shown in the display.
ꢀChangingꢀModes
NOTE: CD, USB and operation of iPod modes will not appear
unless a CD is inserted or USB/iPod devices are connected.
The XDMA5280 offers a 3.5 mm port on the front panel.
Using a 3.5mm male-to-male cable, connect audio device,
MP3 player, etc. to the auxilary input. Press SOURCEꢀto
select AUX-IN mode.
AuxiliaryꢀInput
Adjust volume using volume knob (00-46).
Volume
Display
Press DISP to select between clock and different types of
information, such as radio frequency, CD track/elapsed time
or MP3/WMA song information.
Press RESET upon initial installation or if abnormal
operation occurs. Reset button is located behind the front
panel.
Reset
With the unit on, press and hold DISP until the clock begins
SetꢀtheꢀClock
to flash, then release. Press TUNE
to adjust the hours
nn
and TUNEꢀ
to adjust the minutes. Press DISP momen-
ll
tarily to save the selected time.
The clock will display 12-hour AM/PM time in USA frequency
12/24-hourꢀClockꢀ
SetupꢀMenu
:
spacing mode (10 00 PM). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
Press and hold AUDIO/MENU for more than 3 seconds to
access the setup menu. Press AUDIO/MENU momentarily
to select between the menu functions and rotate the volumeꢀ
knob left/right to adjust or activate the desired function.
6
XDMA5280ꢀOPERATION
GeneralꢀOperationꢀ-ꢀSetupꢀMenu
MenuꢀFunction
Options
Action
AutoꢀStationꢀ
Store
Press SELECT to seek and save 6 strong stations in the
AUTO STORE
LOCAL OFF
LOCAL ON
current band. (Tunerꢀmodeꢀonly)
Activates distance tuning (Tunerꢀmodeꢀonly).
Local/Distanceꢀ
Tuning
Activates local tuning for strong station reception only (Tunerꢀ
modeꢀonly).
Programs the unit to USA tuner spacing.
FREQ USA
FREQ EURO
IPOD FULL
Tuner
Frequency
Spacing
(200kHz for FM and 10kHz for AM). (Tunerꢀmodeꢀonly)
Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM). (Tunerꢀmodeꢀonly)
Programs the head unit to advanced control of the iPod/
iPhone device. (OperationꢀofꢀiPodꢀmodeꢀonly)
SelectableꢀiPodꢀ
Control
Programs the head unit to manual control of the iPod/iPhone
device and allows music to be controlled from the iPod/
iPhone device. (OperationꢀofꢀiPodꢀmodeꢀonly)
IPOD BASIC
CLOCK OFF
CLOCK ON
AUX ON
Programs unit to not display the clock when the power is off.
Programs unit to display the clock when the power is off.
Enables the front panel 3.5mm auxiliary input.
Disables the front panel 3.5mm auxiliary input.
Disables the confirmation beep.
Clockꢀ
Display
AuxiliaryꢀInput
AUX OFF
BEEP OFF
BEEP ON
Beepꢀ
Confirmation
Enables the confirmation beep.
Programmableꢀ
TurnꢀOnꢀVolume
Programs unit to always turn on at a specific volume
(default is OFF). Any volume level 1-46 can be selected.
PRO-VOL #
MSG OFF
MSG ON
Disables power on message. (example: GOOD MORNING)
Enables power on message to be displayed.
Powerꢀonꢀ
Message
Programs unit to scroll information once every 15 seconds
(default).
SCROLL 15 S
Programs unit to scroll once, then show the first 10
characters on display.
Scrollingꢀ
Option
SCROLL ONCE
SCROLL ON
SCROLL OFF
DIMMER HI
Programs unit to scroll continuously.
Programs unit to show the first 10 characters on the display.
Programs unit to the brightest illumination level.
Illuminationꢀ
Dimmer
DIMMER MED Programs unit to the middle illumination level.
DIMMER LOW Programs unit to the dimmest illumination level.
DEMO OFF
DEMO ON
Disables the demonstration mode.
Enables the demonstration message.
Demonstrationꢀ
Mode
7
XDMA5280ꢀOPERATION
GeneralꢀOperation
Audio Press AUDIO momentarily to select between Bass, Treble,
Balance, Fader, Equalizer and Source Volume Level.
BASS
TREBLE
BALANCE
FADER
EQUALIZER
SOURCE LEVEL
Bass Press AUDIO until BASS appears then rotate volume knob
left/right to adjust ( -6 minimum / +6 maximum).
Treble Press AUDIO until TREBLE appears then rotate volume knob
left/right to adjust ( -6 minimum / +6 maximum).
Balance Press AUDIO until BAL appears then rotate volume knob
left/right to adjust (BAL L12 - BAL R12).
BAL EVEN represents equal balance
Fader Press AUDIO until FADER appears then rotate volume knob
left/right to adjust (FADER F12 - FADER R12).
FAD EVEN represents equal fader
Equalizer Press AUDIO until EQ appears then turn the volumeꢀknob
to cycle through the following equalization curves: FLAT
(default), POP, JAZZ, CLASSIC, BEAT, ROCK and USER.
Any manual adjustment to the Bass or Treble settings are
automatically saved as USER.
SourceꢀVolumeꢀLevel The source volume level control allows a gain adjustment
for each audio source: AM, FM, CD, AUX, operation of iPod
and USB. Set the source volume level for each mode,
depending on the relative volume of each audio source.
To set the source volume level, press AUDIO until SRC
LEVEL appears. After one second, the current mode will
appear on the display. Turn the volume knob to adjust
the audio level of the current source (-6 minimum/+6
maximum).
Note:ꢀOnly the current mode will be available for
adjustment. To adjust another mode of operation, press
SOURCEꢀuntil the desired mode is selected, then set the
source volume level for that mode.
8
XDMA5280ꢀOPERATION
AM/FMꢀTunerꢀOperation
SeekꢀTuning Press TUNE
or TUNEꢀ
to seek to the next strong station.
for more than one second
nn
ll
ManualꢀTuning Press TUNE
or TUNEꢀ
momentarily to change
nn
ll
radio frequency up or down one step at a time. Press and
hold to advance quickly.
Bandꢀ Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
StoringꢀandꢀRecallingꢀ Up to 18 FM stations and 12 AM stations can be stored. To
StationꢀPresets store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
9
XDMA5280ꢀOPERATION
CDꢀPlayerꢀOperation
InsertꢀCD With the label facing up, insert a standard size CD into the
CD slot. The CD will automatically begin playback.
EjectꢀCD Press EJECT to eject the CD. The unit will change to
previous mode of operation. If the disc is not removed
within 10 seconds, the unit will reload the disc. The unit
does not have to be turned on to eject CD.
TrackꢀSelect
Press TRACKꢀ
to skip to the beginning of the next
ll
track. Press TRACK
to return to the beginning of the
nn
current track. Pressing TRACK
beginning of the previous track.
again skips to the
nn
FastꢀForwardꢀandꢀReverse
Press and hold TRACKꢀ
or reverse a track.
or TRACK
to fast forward
ll
nn
Pause
Intro
Press
Press
/
/
II to temporarily stop CD playback.
l
II again to resume playback.
l
Press INTꢀto enter the Intro menu, then turn the volume
knob to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ALL - Plays the first 10 seconds of each track.
Repeat
Random
Press RPTꢀto enter the Repeat menu, then turn the volume
knob to select one of the following options:
• ALL - Plays all tracks on CD.
• TRACK - Continuously repeats selected track.
Press RDMꢀto enter the Random menu, then turn the
volume knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL- Plays all tracks in random order.
CD-R/CD-RWꢀCompatibility
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method. In
addition, the following CDs may be incompatible with this
unit:
CDs exposed to extreme temperatures or direct sunlight
for extended periods of time, CDs recorded in which a
recording session failed or a re-recording was attempted
and, or encrypted or copy-protected CDs which do not
conform to the audio CD-DA red book recording standard.
10
XDMA5280ꢀOPERATION
CDꢀPlayerꢀOperationꢀ(MP3/WMAꢀFiles)
PlayingꢀanꢀMP3/WMAꢀDisc When an MP3/WMA encoded disc is first inserted,
“DISC READ” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
DisplayingꢀInformation Press DISP to select between song title, artist, file name,
folder name, track number, and clock/elapsed time.
“NO ARTIST” or "NO TITLE" will be displayed if the MP3/
WMA file contains no ID3 tag information.
ꢀꢀ
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
TitleꢀIconꢀ
ArtistꢀIconꢀ
FolderꢀIconꢀ
FileꢀIconꢀ
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
This icon will illuminate when the folder name is displayed.
This icon will illuminate when the file name is displayed.
ꢀ
ꢀ
CharacterꢀSupport Maximum character display information
• Track name – 32 character maximum
• Directory name – 32 character maximum
• *Song title – 32 character maximum
• *Artist name – 32 character maximum
*Song title and Artist Name will only be displayed if included
with the MP3/WMA file.
When referring to MP3/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name
11
XDMA5280ꢀOPERATION
CDꢀPlayerꢀOperationꢀ(MP3/WMAꢀFiles)
Folder/FileꢀSearchꢀMode MP3/WMA CD mode features a file and folder search mode.
This search allows navigating through folders to find a
specific MP3 or WMA file for playback.
Stepꢀ1 Press SELECT to enter the file/folder search mode. A list of
all the folders on the CD will be displayed.
Note: Any files located in the root directory will be located in
the folder named "ROOT". Press SELECT to view the files on
the root folder.
Stepꢀ2 Turn the volumeꢀknob to cycle through all the folders on the
device and press SELECT to choose the desired folder. The
list of files in the selected folder will be displayed. Turn the
volumeꢀknob to cycle through the list of files.
Note: Pressing ESC when viewing the contents of a folder
will return to the list of folders on the CD. Press ESC again
to exit the search menu.
Stepꢀ3 Once the desired song is displayed, press SELECT to begin
playback of the desired song.
12
XDMA5280ꢀOPERATION
CDꢀPlayerꢀOperationꢀ(MP3/WMAꢀFiles)
FolderꢀAccessꢀ Press
to select the previous folder.
to select the next folder.
Press
*Folder access is only available on MP3/WMA discs recorded
with more than one folder.
Repeat Press RPTꢀto enter the Repeat menu, then turn the volumeꢀ
knob to select one of the following options:
• ALL - Plays all tracks on CD.
• TRACK - Continuously repeats selected track.
• FOLDER - Continuously repeats all files in selected folder.
Random Press RDMꢀto enter the Random menu, then turn the volumeꢀ
knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL - Plays all tracks in random order.
• FOLDER - Plays all tracks in folder in random order.
Note: Random mode is retained in memory when selecting
between other modes and when the unit is turned on/off.
Intro Press INTꢀto enter the Intro menu, then turn the volumeꢀknob
to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ALL - Plays first 10 seconds of each track.
• FOLDER - Plays first 10 seconds of each track in folder.
Note: Folder repeat, random and intro options only function
on MP3/WMA discs recorded with more than one folder.
13
XDMA5280ꢀOPERATION
CDꢀPlayerꢀOperationꢀ(MP3/WMAꢀFiles)
MediaꢀCompatibility
The following types of discs/files are compatible:
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA
• MP3 data
• WMA data
The following types of discs/files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• Discs recorded with Track At Once or packet writing
• MP3 PRO format
• MP3 playlists
• WAV format
PlaybackꢀOrder
MP3/WMA playback sequence is based on recorded order
of files and begins in the root folder of the disc. Any empty
folders or folders that do not include MP3/WMA files are
skipped. This unit may not play files in the order they were
recorded in. Refer to your recording software’s user’s manual
for more information.
CompatibleꢀRecordingꢀ
Formats
• ISO9660 level 1
• ISO9660 level 2
• Yellow Book MODE 1
• Yellow Book MODE 2 FORM 1
• Multi session
• Maximum files - 999
• Maximum folders - 255
• Maximum folder levels - 8
• MPEG-1/2/2.5 Audio Layer-3
ISO9660 standards:
• Maximum nested folder depth is 8 (including the root folder).
• Valid characters for folder/file names are letters A-Z
(all caps), numbers 0-9, and “_” (underscore). Some
characters may not be displayed correctly, depending on
the character type.
• This device can play back discs in Joliet, Romeo, and other
standards that conform to ISO9660. MP3/WMA written in the
formats other than the above may not play and/or their file
names or folder names may not be displayed properly.
14
XDMA5280ꢀOPERATION
CDꢀPlayerꢀOperationꢀ(MP3/WMAꢀFiles)
AdditionalꢀMP3/WMAꢀ An internal buffer provides ESP (Electronic Skip Protection) to
Information virtually eliminate skipping.
When playing a disc recorded with regular audio files
(CD-DA or .WAV) and MP3/WMA files, the unit will play the
MP3/WMA files only.
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be played.
Do not attempt to play discs which contain non-MP3/WMA
files with the MP3/WMA extension.
SamplingꢀFrequencyꢀRates
MP3 8kHz ~ 48kHz
WMA 32kHz ~ 48kHz
TransferꢀBitꢀrates
MP3 32kbps ~ 320kbps constant
Variable bit rates
WMA 32kbps ~ 192kbps constant
Variable bit rates
Note: Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3ꢀTagꢀDisplay ID3 tags Version 1.0 to 2.4.
This model will not display ID3 Version 2.4 or greater tags.
RecommendedꢀSettings For best results, use the following settings when burning an
MP3 disc:
128kbps or higher constant bit rate
44.1kHz or higher sampling frequency
For best results, use the following settings when burning a
WMA disc:
64kbps or higher constant bit rate
32kHz or higher sampling frequency
15
XDMA5280ꢀOPERATION
USBꢀOperationꢀ
To play MP3/WMA files from most USB mass storage
devices, line up the USB connector and insert the USB
device into the XDMA5280's USB port.
ConnectingꢀaꢀUSBꢀDevice
(soldꢀseparately)
PlayingꢀMusic
When a USB device is first connected, “USB READ” will
appear in the display and playback will begin momentarily.
Depending on the number of files and folders, it may take
several seconds for the device to begin playing. If no valid
MP3/WMA files are detected, “NO FILE” will be displayed
and the last mode will be resumed.
TrackꢀSelect
Press TRACKꢀ
to skip to the beginning of the next
ll
track. Press TRACK
to return to the beginning of the
nn
current track. Pressing TRACK
beginning of the previous track.
again skips to the
nn
FastꢀForwardꢀandꢀ
Reverse
Press and hold TRACKꢀ
or TRACK
to fast
ll
nn
forward or reverse a track.
Pause
Press
Press
/
/
II to temporarily stop USB playback.
l
II again to resume playback.
l
FileꢀSearch
Stepꢀ1
Press SELECT to enter the file/folder search mode. A list of
all the folders from the USB device will be displayed.
Note: Any files located in the root directory will be located in
the folder named "ROOT". Press SELECT to view the files on
the root folder.
Stepꢀ2
Stepꢀ3
Turn the volumeꢀknob to cycle through all the folders on the
device and press SELECT to choose the desired folder. The
list of files in the selected folder will be displayed. Turn the
volumeꢀknob to cycle through the list of files.
Note: Pressing ESC when viewing the contents of a folder
will return to the list of folders on the USB device. Press
ESC again to exit the search menu.
Once the desired song is displayed, press SELECT to begin
playback of the desired song.
Note: Due to differences in USB device transfer speeds, it is
recommended to limit each folder to less than 30 songs.
16
XDMA5280ꢀOPERATION
USBꢀOperation
DisplayingꢀInformation When a file is accessed, the clock and elapsed time will be
displayed. Press DISP momentarily to select beween song
title, artist, file name, folder name, track number and clock/
elapsed time.
ꢀꢀ
"NO TITLE" will be displayed if no song title information is
available.
"NO ARTIST" will be displayed if no artist information is
available.
TitleꢀIconꢀ
ArtistꢀIconꢀ
FolderꢀIconꢀ
FileꢀIconꢀ
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
This icon will illuminate when the folder name is displayed.
This icon will illuminate when the file name is displayed.
ꢀ
ꢀ
FolderꢀAccessꢀ Press
to select the previous folder.
to select the next folder.
Press
Note: Folder access is only available on devices with more
than one folder.
Repeat Press RPTꢀto enter the Repeat menu, then turn the volumeꢀ
knob to select one of the following options:
• ALL - Plays all tracks on the device.
• TRACK - Continuously repeats selected track.
• FOLDER - Continuously repeats all files in selected folder.
Random Press RDMꢀto enter the Random menu, then turn the volumeꢀ
ꢀ
knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL - Plays all tracks in random order.
• FOLDER - Plays all tracks in folder in random order.
Note: Random mode is retained in memory when selecting
between other modes and when the unit is turned on/off.
Press INTꢀto enter the Intro menu, then turn the volumeꢀknob
to select one of the following options:
Intro
• OFF - Cancels the INTꢀfunction.
• ALL - Plays first 10 seconds of each track.
• FOLDER - Plays first 10 seconds of each track in folder.
17
XDMA5280ꢀOPERATION
USBꢀOperationꢀ
Maximum character display information
• Track name – 32 character maximum
• Directory name – 32 character maximum
• *Song title – 32 character maximum
• *Artist name – 32 character maximum
CharacterꢀSupport
*Song title and artist name will only be displayed if included
with the MP3/WMA file.
MediaꢀCompatibility
The following types of files are compatible:
• MP3 data
• WMA data
The following types of files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• MP3 PRO format
• MP3 playlists
• WAV format
PlaybackꢀOrder
MP3/WMA playback sequence is based on order the files
are copied to the USB device and begins in the root folder.
Any empty folders or folders that do not include MP3/WMA
files are skipped. Depending on your software, the playback
order may vary.
PlaybackꢀCapacity
• Maximum number of files: 50,000
• Maximum number of folders: 255 plus the root directory
• Maximum number of files in each folder and root: 50,000
Note: If the number of files/folders exceeds the maximum
outlined above, the additional files/folders will be ignored.
Note:ꢀDevices that exceed the maximum number of files or
folders may not function properly.
USBꢀDeviceꢀCompatibility
Due to the differences of USB devices, some devices may
not be compatible. USB devices must be ‘mass storage
class’ and formatted to the FAT or FAT32 file system in
order to ensure compatibility.
18
XDMA5280ꢀOPERATION
USBꢀOperation
AdditionalꢀMP3/WMAꢀ Only MP3 files with filename extension (.mp3) can be played.
Information Only WMA files with filename extension (.wma) can be
played. Do not attempt to play non-MP3/WMA files with the
MP3/WMA extension.
SamplingꢀFrequencyꢀRates
MP3 8kHz ~ 48kHz
WMA 32kHz ~ 48kHz
TransferꢀBitꢀrates
MP3 32kbps ~ 320kbps constant
Variable bit rates
WMA 32kbps ~ 192kbps constant
Variable bit rates
Note: Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3ꢀTagꢀDisplay ID3 tags Version 1.0 to 2.4
Note: If an invalid ID3 tag version is detected, "NO
SUPPORT" will scroll on the display.
19
XDMA5280ꢀOPERATION
OperationꢀofꢀiPod
ConnectꢀanꢀiPodꢀDevice The XDMA5280 features a direct USB control system for iPod. To
(NotꢀIncluded) play music from an iPod device, connect the USB cable (includedꢀ
withꢀyourꢀiPodꢀdevice) to the XDMA5280's USB port. Once connected,
"USB READ" is shown shortly, then "IPOD/IPHONE READ" will
appear in the display. Playback will begin automatically. If a song is
playing on the iPod device before it is connected, it will continue to
play.
DisplayingꢀInformation Press DISP to select between artist, song title, album, elapsed time,
clock and track number.
SearchꢀMode
SearchꢀMenuꢀFunctions
(stepꢀ1)
Press SELECT once to enter the search mode.
(stepꢀ2)
Turn the volume knob to select between playlist, artist, album,
songs,ꢀaudiobook and podcast. Press SELECT to select the desired
search type.
(stepꢀ3)
Navigate to the desired song and press SELECT to begin playback
of that song. Use the table below for reference when navigating
through the menu options.
Note: Press ESC to access the previous level (up one level). Pressing
ESCꢀfrom the search main menu will exit the search.
See the below table for a list of the search menu navigation options.
Menu Navigation
Songs
Search Item
Menu
Playlists
Playlist
Artists
Menu
Menu
Menu
Menu
Menu
Artists
Albums
Songs
Songs
Albums
Songs
Audiobooks
Podcasts
Albums
Songs
Audiobooks
Podcasts
Full/ManualꢀControl
The XDMA5280 features both full and manual control modes for iPod/iPhone devices. See page 7 for
details to toggle the control between full and manual modes.
Important: To support manual control for iPod/iPhone, the iPod device must be updated to the newest
firmware using iTunes.
Note: Not all iPod/iPhone devices are compatible with manual control mode.
20
XDMA5280ꢀOPERATION
OperationꢀofꢀiPod
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀSongꢀSelect
Press
to skip to the beginning of next song. Press
ll
to return to the beginning of current song. Pressing
nn
again skips to the beginning of previous song.
nn
ꢀꢀFastꢀForwardꢀandꢀ
Press and hold
or
to fast forward or reverse a
ll nn
Reverse
ꢀꢀ
song.
Pause
Press / II again to resume playback.
Press / II to temporarily stop playback.
l
l
Repeat
Press RPTꢀto enter the Repeat menu, then turn the volume
knob to select one of the following options:
• ALL - Repeats all tracks.
• SONG - Repeats selected track.
Random
Press RDMꢀto enter the Random menu, then turn the
volume knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL- Plays all tracks in random order.
• ALBUM - Plays all tracks in the selected album in
random order.
Intro
Press INTꢀto enter the Intro menu, then turn the volume
knob to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ON - Plays first 10 seconds of each track.
CharacterꢀSupport
Only alphanumeric characters can be displayed (ASCII
type). "NO SUPPORT" will be displayed if the file contains
characters that can not be displayed. "NO FILE" will be
displayed if there are no songs in the selected playlist.
Maximum character display information
• *Song title – 32 character maximum
• *Artist name – 32 character maximum
• *Album name – 32 character maximum
*Song Title, Artist Name and Album name will only be
displayed if included with the file.
DeviceꢀCompatibility
Made for
• iPod touch (4th generation)
• iPod nano (6th generation)
• iPod touch (3rd generation)
• iPod nano (5th generation)
• iPod touch (2nd generation)
• iPod nano (4th generation)
• iPod classic
• iPhone 4
• iPhone 3GS
• iPhone 3G
• iPhone
21
XDMA5280ꢀWARRANTY
LimitedꢀOneꢀYearꢀWarranty
This warranty gives you specific legal
Whatꢀtoꢀdo?
rights. You may also have other rights
which vary from state to state.
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any
custom controls may save you a service
call.
Dual Electronics Corp. warrants this
product to the original purchaser to be free
from defects in material and workmanship
for a period of one year from the date of
the original purchase.
2. If you require service during the
warranty period, you must carefully
pack the product (preferably in the
original package) and ship it by prepaid
transportation with a copy of the original
receipt from the retailer to an
Dual Electronics Corp. agrees, at our
option, during the warranty period,
to repair any defect in material or
workmanship or to furnish an equal
new, renewed or comparable product
(whichever is deemed necessary) in
exchange without charges, subject to
verification of the defect or malfunction and
proof of the date of purchase. Subsequent
replacement products are warranted for
the balance of the original warranty period.
authorized service center.
3. Please describe your problem in
writing and include your name, a
return UPS shipping address (P.O. Box
not acceptable), and a daytime phone
number with your shipment.
4. For more information and for the
location of the nearest authorized
service center please contact us by one
of the following methods:
Whoꢀisꢀcovered? This warranty is extended
to the original retail purchaser for products
purchased from an authorized Dual dealer
and used in the U.S.A.
• Call us toll-free at 1-866-382-5476
• E-mail us at [email protected]
Whatꢀisꢀcovered? This warranty covers all
defects in material and workmanship in
this product. The following are not covered: Exclusion of Certain Damages: This
software, installation/removal costs,
damage resulting from accident, misuse,
abuse, neglect, product modification,
improper installation, incorrect line
voltage, unauthorized repair or failure
to follow instructions supplied with the
product, or damage occurring during
return shipment of the product. Specific
warranty is exclusive and in lieu of any
and all other warranties, expressed or
implied, including without limitation the
implied warranties of merchantability and
fitness for a particular purpose and any
obligation, liability, right, claim or remedy
in contract or tort, whether or not arising
from the company’s negligence, actual
license conditions and copyright notices for or imputed. No person or representative
com.
is authorized to assume for the company
any other liability in connection with the
sale of this product. In no event shall the
company be liable for indirect, incidental or
consequential damages.
22
XDMA5280ꢀOPERATION
Troubleshootingꢀ
Problem
Cause
Action
Yellow wire not connected or incorrect
voltage Red wire not connected or
incorrect voltage
Check connections for proper
voltage (11~16VDC)
Unitꢀwillꢀnotꢀturnꢀonꢀ
(noꢀpower)
Black wire not connected
Fuse blown
Check connection to ground
Replace fuse
Speaker wires not connected
Check connections at speakers
Unitꢀhasꢀpowerꢀ
(butꢀnoꢀsound)
Insulate all bare speaker wires
from each other and chassis
ground
One or more speaker wires touching
each other or touching chassis ground
Yellow or red wire touching chassis
ground
Check for pinched wire
Unitꢀblowsꢀfuses
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Use fuse with correct rating
Unit is not mounted correctly or
backstrap is not secure
Check mounting sleeve and
backstrap support
Excessiveꢀskipping
Physical defect in media (CD, CD-R or
CD-RW)
Check media for scratches
ERRORꢀ2ꢀappearsꢀ
onꢀdisplay
Disc read error or disc is in upside
down
Press eject or RESET
PROTECTꢀappearsꢀ
onꢀdisplay
The WMA file is copy-protected by DRM Write disc using WMA files that
(Digital Rights Management)
are not copy-protected
NOꢀFILEꢀappearsꢀ
onꢀdisplay
Selected file is not available in direct or
alphanumeric search modes
Repeat search using valid
parameters
Press and hold EJECTꢀ
for 3 seconds to reset CD
mechanism position
CD mechanism position out of
alignment
Unitꢀwillꢀnotꢀacceptꢀ
aꢀdisc
Remove 2 transit screws
located on top of the unit
CD transit screws still in place
An invalid ID3 tag version is present
An ID3 tag character is not supported
Version 1.0 to 2.4 ID3 tags are
supported.
NOꢀSUPPORTꢀappearsꢀ
onꢀdisplay
Only ASCII characters are
supported.
23
XDMA5280ꢀOPERATION
Specifications
CDꢀPlayer Frequency response: 10Hz-20kHz
Channel separation @ 1kHz: >65dB
D/A converter: 1ꢀBit
FMꢀTuner Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AMꢀTuner Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
General Speaker output impedance: 4~8ꢀohms
Line output voltage: 2ꢀVoltsꢀRMS
Dimensions: 7"ꢀxꢀ7"ꢀxꢀ2"ꢀ(178ꢀxꢀ178ꢀxꢀ51ꢀmm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 18 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
24
XDMA5280ꢀOPERATION
FCCꢀCompliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
25
XDMA5280ꢀOPERATION
Notes
26
XDMA5280ꢀOPERATION
Notes
27
Dual Electronics Corp.
Toll Free: 1-866-382-5476
©2011 Dual Electronics Corp. All rights reserved.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or
iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible
for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this
accessory with iPod or iPhone may affect wireless performance.
Other trademarks and trade names are those of their respective owners.
NSA0711-V01
|