BRASS COMPASS
(LARGE)
42433
ASSEMBLY & OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
REV 01/05
Warning:
The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking your Compass, check to make sure the following parts are included. If any parts
are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.
Operation
This manual explains the parts and basic use of the Compass. It is important that you read the
entire manual to become familiar with the product BEFORE you use the Compass.
We recommend you use a separate book (not included) on Compass usage or Orienteering, to learn
how to use the Compass for more complex applications.
providing additional information that was included in this manual. This information was used with his
permission.
The Brass Compass is a type of compass called a “mirror compass.” It has many uses and can be
used for the practical measurement of angles.
All magnetic compasses use the Earth’s magnetic field to supply a reference direction for the
measurement of horizontal angles. This direction has a fundamental significance only when the
directions on the earth’s surface are to be specified, and then the magnetic declination must be
taken into account.
This Compass can determine the magnetic heading of an object and its angle of elevation or declination.
Magnetic declination is the difference between the true geographic north (north pole) and the magnetic
north (in northern Canada).This variation fluctuates throughout the world.
The following list will explain the uses of the parts of the Compass highlighted in FIGURES 2 and 3.
1. Mirror -This is used to view the compass capsule. It is designed in this way so you can see
your target and get a measurement at the same time. When hinged at 45 degrees, the
mirror can aid in finding the altitude angle measurements while simultaneously looking
at the object.
Note: To get proper directional orientation, the mirror should be used to read the
compass.
2. Graduated Dial - By increments of 1 degree, the dial is graduated 0 degrees through 360
degrees. It is used to read compass bearings.
3. Levels - Allows for altitude and angles measurement as well as plumb leveling.
4. Clinometer Arrows - The arrow pointing to the ground when the Compass is on its side, is used
in conjunction with the orienting circles to measure angle of inclination.
SKU 42433
For technical questions please call 1-800-444-3353.
Page 3
5. Pendulous Arm - To read the vertical angle of an object of elevation or declination.
6. Magnetic Declination Scale - Works in conjunction with the Pendulous Arm for reading angles of
elevation and declination.
7. Compass Needle - To be used with the Graduated Dial for basic bearings. The Red Mark points
toward magnetic north.
8. Peep Sight - With the Lid fully open, you can use the Peep Sight in conjunction with the Mirror to
look directly at an object while taking a reading. Warning: Do not look at the Sun.
9. Sine Chart - Standard geometrical reference numbered 1 to 45 degrees of angle and the figure
opposite each degree is the linear measurement from the baseline at 1 inch from the vertex
of the angle. For example: Envision 2 lines meeting to form a 45 degree angle. The point
they meet is the vertex. Add 1 inch from this point; the measurement from one line to the
other is .707 inches-see Figure 1.
Figure 1-Sine Chart
Opening up the Compass
The Compass opens up into two sections. The lower section contains the Magnetic Needle, the
Graduated Circle, and a Sight. The upper section contains the Mirror, a Sighting Line and a Sight.
Note:
The Compass produces best results when it is used on a firm, level surface.
Preparing the Compass for Use
The Compass contains a Circular Bubble Level. Check the Circular Bubble Level to make certain
that the Compass is perfectly horizontal. Make certain that the Needle is free to rotate. Extend the
Front Sight making certain that the slotted part is horizontal and that the sight is vertical.
Sighting with the Compass
Take a sighting of the object you wish to measure. A sighting can be taken either by the mirror or
using the Sight. Once the object is sighted, press down the needle clamp so that the Needle is held
in a fixed position. Note the position before unclamping the Needle.
SKU 42433
For technical questions please call 1-800-444-3353.
Page 4
Azimuths
The direction of a line can be specified by its azimuth, the angle the north end ot the compass’
horizontal projection makes with north (magnetic or true), measured clockwise from 0 degrees to
360 degrees.
Measuring a Horizontal Angle
1.
2.
To measure a horizontal angle, adjust the Mirror so that when you look into the Mirror you
see the Front Sight.
Move the Compass around until the Sighting Line is lined up with the tip of the Front Sight
and with the object you are sighting. The Compass is now aligned.
3.
4.
Read and note the position of the Needle. This will give you an accurate reading to 1 degree.
Sight a second object the same way as in steps 1,2 and 3. The difference in the azimuths
obtained by the two sights is the angle between the lines from you, the observer, to the two
objects. For instance, if object one is at 280 degreess and object 2 is at 170 degrees,
the angle is 280-170 = 110 degrees.
Measuring an Angle with the Compass Firmly Supported
1.
2.
Use this method only if the Compass is firmly supported. Open the Compass up
completely. Look through the aperture near you to the tip of the far Sight. Line up the object
in these sights. The Compass is now aligned.
Making certain that the Compass does not move, move your eye away from the Sights and
note the measurement on the Compass.
Measuring a Vertical Angle
Located in the lower half of the Compass are an index and Vernier that can be rotated by an arm on
the outside of the Compass case. Also there is a Bubble Level, and a Circular Level. Finally, there
are two scales. The inner one measures in degrees to + or - 90o. The outside scale measures in
percent grade, from 0% to 100%.
1.
2.
3.
Sight from the Front Sight thorugh the small hole in the Mirror. Adjust the Mirror so that you
can see the Frame and the Bubble Level.
Move the Lever so that the Bubble Level is centered while you are sighting the desired
object.
Note the reading on the Scales.
Estimating the Inclination of a Line
The inclination of a line can be estimated by opening the Compass all the way up. Line up the edge
of the case with the line that you want to estimate the inclination of. Move the lever until the Level
Bubble is centered. Note the reading.
SKU 42433
For technical questions please call 1-800-444-3353.
Page 5
Figure 2
Sine Chart (see Figure 1)
(on lid-not shown)
Mirror
Sight Line
Spyhole
lid
Figure 3
Pendulous Arm
Graduated Dial
Red Mark
Bubble
Level
Needle
Magnetic Declination
Scale
Bubble Level
Clinometer
Arrows
SKU 42433
For technical questions please call 1-800-444-3353.
Page 6
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
A
B
B
SKU 42433
For technical questions please call 1-800-444-3353.
Page 7
|