Directed Electronics Directed Video OHD901 User Manual

O W N E R ’ S G U I D E

INSTALLATION GUIDE

9” (16:9)

Overhead Video

Monitor/DVD Player

MODEL OHD901

Table of Contents

Non-Transferable Limited One Year Consumer Warranty . . . . . . . . . . . . . . . . . . . . . .2

Safety Instructions and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

What’s Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . .6

Important . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

When Cleaning the Vehicle .............................................................................6

While Driving ...............................................................................................6

When Parked ................................................................................................7

Proper Use ...................................................................................................7

Disc Handling and Cleaning ............................................................................7

Repairs........................................................................................................7

Radio/TV Tuner Use.......................................................................................7

Installation..................................................................................................7

Picture Quality..............................................................................................8

Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

FCC Notice ...................................................................................................8

Your Warranty...............................................................................................8

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Monitor .......................................................................................................9

DVD—Mounted............................................................................................10

DVD—UnMounted........................................................................................12

DVD—Memory Card Mounting........................................................................13

DVD Player—Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

DVD Playerr—Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Setting the Screen Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Remote Buttons ..........................................................................................16

IR Remote Feedthrough................................................................................17

Battery Replacement....................................................................................18

Precautions ................................................................................................18

Loading and Unloading Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Loading Disc...............................................................................................18

Unloading Disc............................................................................................19

Operating the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Open/Close the Display Monitor.....................................................................20

Power Up/Down the Display Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Source (Mode) ............................................................................................21

Menu (Console Menu)...................................................................................21

Door Light On/Off .......................................................................................22

Courtesy Light On/Off ..................................................................................22

Basic Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

DVD Playback..............................................................................................23

Play/Pause (DVD/MP3/CD) ............................................................................24

Stop (DVD/MP3/CD).....................................................................................24

Selecting a Track or Chapter..........................................................................25

MP3 and JPEG Playback on CD or Memory Card ................................................25

Playback Programming .................................................................................26

Advanced Playback (DVD/MP3/CD).................................................................27

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Accessing Setup Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

1. TV System .............................................................................................29

2. Screen Saver..........................................................................................29

3. TV Type.................................................................................................30

4. Password...............................................................................................30

5. Rating (Parental Settings)........................................................................30

6. Default .................................................................................................31

7. Exit......................................................................................................31

Language Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

1. OSD Language........................................................................................31

2. Audio Lang............................................................................................31

3. Subtitle Lang.........................................................................................32

4. Menu Lang.............................................................................................32

Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Precautions ................................................................................................32

Electrical Connections..................................................................................33

Signal Connection........................................................................................34

Typical Wiring Diagram.................................................................................35

Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

System Wiring Diagram Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .339

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Safety Instructions and Cautions

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIP-

MENT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND

ANNOYING INTERFERENCE, USE ONLY THE INCLUDED HARDWARE.

THIS MONITOR IS ONLY DESIGNED FOR REAR SEAT PASSENGER VIEWING AND IS NOT

INTENDED FOR VIEWING BY THE DRIVER WHILE THE VEHICLE IS IN MOTION. SUCH USE MAY

DISTRACT THE DRIVER OR INTERFERE WITH THE SAFE OPERATION OF THE VEHICLE, AND

MAY ALSO VIOLATE STATE LAW.

DIRECTED ELECTRONICS, INC. DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY,

INCLUDING FATALITIES, OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR

UNINTENDED USES OF THIS PRODUCT.

SHOULD THE LCD PANEL BREAK OR LEAK FLUID, AVOID ALL CONTACT WITH THE UNIT. IF

YOU SHOULD COME IN CONTACT WITH THE LEAKED FLUID, WASH THE AFFECTED AREA

THOROUGHLY WITH WATER AND SEEK IMMEDIATE MEDICAL ATTENTION.

DO NOT CLOSE THE LCD SCREEN IF A MEMORY CARD HAS BEEN INSERTED INTO THE DVD

PLAYER. THIS CAN CAUSE THE LCD PANEL TO BREAK OR LEAK FLUID (SEE ABOVE WARN-

ING). REMOVE MEMORY CARD(S) BEFORE CLOSING SCREEN.

■

During operation, if the unit should over-heat or malfunction, switch off the unit and see your

dealer. Do not disassemble the unit as there are no user-serviceable parts in this unit and the war-

ranty will be voided.

■

Should there be a need to replace a blown fuse, turn off the unit and disconnect all power to

the player. Use only the correct rating fuse to avoid electrical damage to the unit.

■

Only operate the monitor as described in this guide. Attempts to use or modify this monitor

contrary to the descriptions in this guide may cause damage and void the warranty.

■

Extremes in temperature can cause abnormal display operation. This monitor has an optimal

operating temperature range between 32–120 degrees Fahrenheit. If the vehicle interior is outside

this range, do NOT operate the monitor until the temperature is within its operating range.

■

Exposure to moisture or dust can cause harmful damage to the internal electronics. Do not

mount near cup holders or in areas where spills may occur.

■

This monitor is designed for use in vehicles with standard (-) 12 volt ground electrical systems.

■

Do not operate for an extended period of time without the engine running or the vehicle’s bat-

tery voltage may drop to levels precluding engine starting.

■

Do not drop the LCD panel or subject it to direct impact. This will damage the panel and/or

the back light element.

■

When operating the unit, avoid contact with the LCD panel.

Prevent metal or foreign objects being locked between the LCD screen and the enclosure.

Foreign objects may impair smooth running of the disc and may cause electrical problems.

■

Keep unit away from equipment with strong magnets such as large loudspeakers.

■

To prevent malfunction, do not play discs other than the ones listed below: DVD audio discs, CD-

ROMs, JPEGs, MP3s and DVDs with region numbers other than this player's region number.

Welcome

Thank you for your purchase of Directed’s Overhead Monitor with integrated DVD. Prior to operating

this unit, please fully read this instruction manual and retain it for future reference.

What’s Included

The following items are included with your purchase:

z Monitor with DVD Player

z A/V Switch Box

z Power Harness

z DIN Cable

z (2) Headphones

z Domelight Harness

z Mounting Trim Bezel

z A/V Cable for DVD Player

z AC/DC Adapter for DVD Player

z Remote Control

z Mounting Plate (with 4 screws)

Important

WHEN CLEANING THE VEHICLE

Do not spray this unit with water or cleaning solutions. Moisture and the chemicals found in cleaning

fluids could damage the consoles finish and interior electronics. A soft damp, lens cleaning cloth

should be used to wipe the screen. Do NOT use any type of scouring pad, abrasive cleaners, or solvents.

WHILE DRIVING

This unit is intended for use in the rear seat area only. It is illegal in some jurisdictions to install the

unit in a location that would allow the driver to view it while driving.

WHEN PARKED

The screen is easily visible when deployed. Always close the screen when parking for an extended

period of time to avoid potential theft or extended exposure to direct sunlight.

PROPER USE

Do not touch the screen. Do not pull or hang from the fold down monitor door.

DISC HANDLING AND CLEANING

Always handle the discs by the edge. Never touch the shiny side of the discs, as this can impair prop-

er playback.

Mount and dismount the discs with care not to damage or scratch the shiny side of the disc. This

will cause playback faults.

Do not expose the discs to direct sunlight.

After playing, store the disc back in its case.

To clean the disc, use a clean soft lint-free cloth and wipe the disc from the center out. Do not wipe

with a circular motion. Do not use any solvents.

REPAIRS

If the monitor stops working for any reason, discontinue use immediately and consult with your

retailer about any necessary repairs.

RADIO/TV TUNER USE

When the unit is used in conjunction with a Radio/TV tuner, please assure that the receiver is man-

ufactured to receive television broadcast signals that are transmitted via terrestrial radio waves.

Reception quality will change and vary according to vehicle location and weather conditions.

INSTALLATION

Avoid installing the monitor at a location, where it will be under direct sunlight or a hot air vent.

The operating temperature of the unit is from 32–120°F (0–50°C). Install the unit at a dry location,

where it is away from condensation.

Use only the correct size fasteners and cables during installation. Failure to do so may cause a

mechanical or electrical failure and create a fire hazard. The installation should be done by an

authorized Directed dealer.

NOTE: If the internal temperature of the vehicle is higher than the normal oper-

ating temperature, please allow the vehicle to cool down (or warm up) prior

to operating the unit.

PICTURE QUALITY

The picture quality of this LCD unit depends strictly on its installed location. To achieve the best

picture quality, adjust the brightness control or viewing angle of the unit until the optimum view-

ing is achieved.

Important Information

FCC NOTICE

This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interfer-

ence received, including interference that may cause undesirable operation.

Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate this device.

YOUR WARRANTY

Your warranty registration must be completely filled out and returned within 10 days of purchase.

Your product warranty will not be validated if your warranty registration is not returned. Make sure

you receive the warranty registration from your dealer. It is also necessary to keep your proof of pur-

chase, which reflects that the product was installed by an authorized dealer.

Controls

MONITOR

1. DOME LIGHTS—Quantity 2.

2. DOOR LIGHT On/Off—Engage this switch to have the door open switch activate

the dome lights.

3. OPEN/CLOSE—The latch to open or close the LCD screen.

4. COURTESY LIGHT—Activate this switch to "ON/OFF" to activate the dome lights on the

monitor.

5. POWER—Power On/Off button, Source Select button. Hold for 3-seconds to turn power off.

Each press of this button cycles through sources DVD, AV1, or AV2.

UP Button—Used in conjunction with the MENU button to scroll up (or increase) the

menu setting.

7. MENU—Used to set FM Frequency, Brightness, Contrast, Saturation, Hue, or Reset (menu param-

eters). The menu will exit if no action is taken within a few seconds.

DOWN Button—Used in conjunction with the MENU button to scroll down (or decrease)

the menu setting.

9. IR Receiver—Infrared receiver which receives commands from the remote control.

DVD—MOUNTED

The illustration below shows the DVD player mounted in a typical LCD monitor.

1. LOCK/UNLOCK—To dock or undock the DVD player.

2. OPEN—Press this button to open the access door to mount or dismount a disc.

3. AUDIO—Each press of this button accesses each audio track recorded on the DVD (multiple lan-

gauges, commentary, etc.)

4. MENU—Displays the menu on the DVD. Use the Up, Down, Left, and Right buttons to scroll

through the available selections. Use the Enter button to select.

5. UP—

6. DOWN—

7. LEFT—

8. RIGHT—

9. ENTER

10. PLAY/PAUSE—When pressed pauses the playback until pressed again.

11. STOP—Halts playback. If the Play button is pressed the playback will continue from where

stopped. If the Stop button is pressed twice, playback will now start from the beginning.

WARNING: DO NOT CLOSE THE LCD SCREEN IF A MEMORY CARD HAS BEEN INSERTED INTO

THE DVD PLAYER. THIS CAN CAUSE THE LCD SCREEN TO BREAK OR LEAK FLUID. IF YOU

SHOULD COME IN CONTACT WITH LEAKED FLUID, WASH THE AFFECTED AREA THOROUGHLY

WITH WATER AND SEEK IMMEDIATE MEDICAL ATTENTION. REMOVE ALL MEMORY CARDS

BEFORE CLOSING THE LCD SCREEN.

12. MS Card—Memory Stick, allows playback of music, photographs, movies, etc.

13. SD Card—Secure Digital, allows playback of music, photographs, movies, etc.

14. CF Card—Compact Flash, allows playback of music, photographs, movies, etc.

NOTE: To read from a memory card, there must not be mounted a DVD or CD in the

player and the player door must be closed. Only 1 memory card can be

inserted into the player at a time.

* These buttons are used to navigate through the menus on the screen and then use the Enter but-

ton to select the option.

DVD—UNMOUNTED

The illustration below shows the side of the DVD player when removed from the LCD monitor.

VOL

PHONE A/V OUT

DC 12V

1. Electrical connector—This connector provides the electrical interface when mounted in the LCD

monitor.

2. VOL Control—Controls the volume to the phone jack output.

3. PHONE Jack—An optional headphone set can be connected here.

4. A/V OUT Jack—Audio/video output jack.

5. DC 12V Jack—Input power.

6. IR Receiver—For receiving commands from the remote control.

DVD—MEMORY CARD MOUNTING

Ensure that the memory cards are mounted with the logo side of the memory cards oriented with the

arrows as shown below:

Memory Stick

Logo

Side

Logo

Side

Logo

Secure Digital

Side

Compact Flash

WARNING: DO NOT CLOSE THE LCD SCREEN IF A MEMORY CARD HAS BEEN INSERTED INTO

THE DVD PLAYER. THIS CAN CAUSE THE LCD SCREEN TO BREAK OR LEAK FLUID. IF YOU

SHOULD COME IN CONTACT WITH LEAKED FLUID, WASH THE AFFECTED AREA THOROUGHLY

WITH WATER AND SEEK IMMEDIATE MEDICAL ATTENTION. REMOVE ALL MEMORY CARDS

BEFORE CLOSING THE LCD SCREEN.

DVD Player—Installation

1. Ensure power to the monitor is off and that the ignition key is off.

2. Align the notches in the side of the player with the tabs in the sides of the monitor DVD mount-

ing area and slide the player into the monitor.

3. Slide the player towards the LCD screen until the lock/unlock button latches.

NOTE: If the DVD player doesn’t power up correctly, remove the player (see instruc-

tions below) and then re-install.

Insert DVD Player

and then slid down

until unit locks.

ꢀ

Lock/Unlock

Button

Electrical

Connector

DVD Player—Removal

1. While holding and supporting the DVD player.

2. Move and hold the lock/unlock button to the right.

3. Slide the player away from the screen and carefully remove.

Setting the Screen Mode

The overhead monitor has 4 different screen modes. These are: FULL, NORMAL, WIDE, and ZOOM.

Press the Image

button on the remote control to access the different screen modes. The last

mode set is displayed on the screen. Each time the Mode button is pressed, the screen switches in

the following sequence.

Remote Control Unit

REMOTE BUTTONS

1. POWER (source)

2. IR (on/off)

28. ANGLE

29. SUBTITLE (on/off)

ꢀ

3. FM (on/off)

30. DOWN (Cursor)

31. AUDIO

4. Picture (PIP)

5-7. Numeric

(n/a in this model)

32. ZOOM (2, 3, 4, 1/2, 1/3, 1/4, OFF)

33. F.REV (Fast Reverse)

34. PLAY/PAUSE

8. UP (display)

9-11. Numeric

12. Console MENU

13-15. Numeric

35. F.FWD (Fast Forward)

36. SLOW

16. DOWN (display)

17. MENU/PBC

37. BACK

38. STOP

18-19 Numeric

39. NEXT

20. Image

(wide, zoom, full, normal)

40. REPEAT

21. TITLE

41. POWER (Tuner)*

42. DSP (channel display)*

43. TV/AV (selects Tuner or Aux input)*

44. DISPLAY

22. UP (Cursor)

23. SETUP

ꢀ

24. MUTE (on/off)

25. LEFT (Cursor)

26. ENTER

45. CH+ (channel up)*

46. CH- (channel down)*

47. AUTO (auto programming of TV channels)*

48. PROGRAM

27. RIGHT (Cursor)

IR REMOTE FEEDTHROUGH

The remote will operate, through the monitor, and transmit commands to other compatible devices

attached to the AV1 or AV2 source at the switch-box. The IR signals are compatible with models

DV2602, DV2605 DVD players, and TV100 tuner.

* These buttons are for use only with the TV tuner (model TV100).

BATTERY REPLACEMENT

NOTE: Before using remote after installation, remove the battery plastic protective slip.

Remote Controller

+ side

Battery

Latch

Battery Holder

1. Move the small latch to the right and slide out the battery holder.

2. Remove old battery and replace it with a new battery (CR2025) with the positive “+” sign facing

as shown above.

3. Push battery holder back into its compartment until it is locked.

PRECAUTIONS

1. Properly dispose of used battery.

2. Do not misuse battery by shorting the positive “+” and negative “-” terminal or put it into fire.

Overheating may cause the battery to explode and cause a fire hazard.

3. If the remote is not to be used for a long period, remove the battery from the remote to prevent

damage from battery leakage.

4. To avoid accidents, prevent children from playing with the battery.

Loading and Unloading Discs

You can use single side and dual layer DVDs, VCDs, CD-audio and CD-R compatible 12cm discs with

this system.

LOADING DISC

1. Press OPEN at the upper right corner to open the door.

2. Load with the recorded side (the shiny side) facing up. With double-sided discs, load with the

side you want to watch facing up. Ensure that the disc is seated properly before pushing tray back

into its locking position.

3. Push to close the door.

UNLOADING DISC

1. Press OPEN at the upper right corner to open the door.

2. Remove the disc. (Avoid touching the recorded surface.)

3. Push to close the door, until you hear a click sound from the door mechanism.

Operating the Monitor

OPEN/CLOSE THE DISPLAY MONITOR

To open the display monitor, push the "OPEN" button and pull the monitor down by the middle of the

LCD to the desired position.

WARNING: THE LCD MONITOR MUST ALWAYS BE OPENED, CLOSED, OR POSITIONED FROM

THE MIDDLE OF THE SCREEN AS SHOWN BY THE POINTING HAND BELOW. DO NOT USE THE

CORNERS OF THE SCREEN, THIS CAN RESULT IN DAMAGE/LEAKAGE OF THE SCREEN.

To Open—push center button

Use this portion of the

screen for opening, closing,

Open Position

and positioning.

WARNING: DO NOT CLOSE THE LCD SCREEN IF A MEMORY CARD HAS BEEN INSERTED INTO

THE DVD PLAYER. THIS CAN CAUSE THE LCD SCREEN TO BREAK OR LEAK FLUID. IF YOU

SHOULD COME IN CONTACT WITH LEAKED FLUID, WASH THE AFFECTED AREA THOROUGHLY

WITH WATER AND SEEK IMMEDIATE MEDICAL ATTENTION. REMOVE ALL MEMORY CARDS

BEFORE CLOSING THE LCD SCREEN.

To close the display monitor, push the LCD screen up until it latches closed with an audible click.

Note: The ignition key must be in the Accessory or Ignition position in order for

the monitor to have power.

Power Up/Down the Display Monitor

The unit will power up when the display monitor is unlatched and pulled down. (If the unit does

not power up, press the Power

side of the LCD screen.

button on either the remote or the Power button on the left

To turn the power off to the unit, press and hold for 3-seconds the POWER

button on the

remote or the Power button on the left side of the LCD screen. The power will also shut Off when

the display monitor is placed in the closed and latched position.

If the hand

icon or “INVALID KEY” displays in the upper left-hand corner of the screen when

using the remote, it indicates that the command issued is not allowed during the mode that the

monitor display is presently in, or is not available on this system.

SOURCE (MODE)

Press the

(SOURCE) button on the remote or momentarily press the POWER button on the left

side of the LCD screen to select the input signal AV1, AV2 or DVD.

MENU (CONSOLE MENU)

Press MENU button on the left side of the LCD screen or the

button on the remote to activate

the screen parameters set-up. The sequence of set-up items is as follows:

FM →

SHARPNESS → BRIGHTNESS → CONTRAST →

SATURATION → HUE → RESET

FM: Transmitting frequency

BRIGHTNESS: Brightness adjustment

SATURATION: Color saturation adj.

SHARPNESS: Sharpness adjustment

CONTRAST: Contrast adjustment

HUE: Color hue adjustment

RESET: Resets above (except FM) to factory default settings.

Once the desired setting is selected, press the cursor buttons to adjust the setting. On the remote

use the up/down cursor buttons located at either side of the menu button. On the monitor use the

cursor buttons to the right side of the

button. If a button is not activated within 5 seconds,

this function mode will turn OFF. Once the correct function is selected, press the cursor button (to

set the desired setting). If no button is pressed, the menu mode will turn OFF in about 5 seconds.

The FM frequency setting allows the monitor to transmit audio to the vehicle’s radio. Use a frequency

that is not interfered with from a local broadcast station. This setting also has an OFF position.

DOOR LIGHT ON/OFF

Engage this switch

on the monitor to activate the dome lights when a door is open.

NOTE: This function is operational only when the Gray wire of the dome light cir-

cuit is connected to the door switch.

COURTESY LIGHT ON/OFF

Activate this switch

on the monitor to control the dome light illumination.

Basic Functions

DVD PLAYBACK

1. Press the remote control’s POWER

switch on the unit’s power.

button or the monitor’s POWER button to

2. Select video source (DVD).

NOTE: If there is no disc in the DVD player, a “NO DISC” message will be displayed

in the upper left corner of the screen.

3. Load a disc into the unit. The message “READ” will appear in the upper left corner of the

screen.

4. DVD playback commences.

NOTE: The disc will start to play if there are no titles recorded on the disc. If one or

more titles are recorded on the disc, a menu will appear on the LCD screen.

5. Press

on the remote (or their equivalent on the DVD player) to select the

ꢀ

preferred item or title from the menu.

6. Press the ENTER (on remote or DVD player) button, the selected item will now start playing.

7. To return to the menu screen, press the DVD MENU button.

8. After viewing completion, press the POWER

button to put the unit into standby mode.

NOTE: If the “WRONG REGION” message appears, it means that the corresponding

operation is prohibited either by the player or by the disc.

FAST FORWARD OR REVERSE (DVD/MP3/CD)

1. Press the "FF"

button during playback. Each time this button is pressed, the unit will go

into a rapid advance playback mode. This will be shown on the LCD, depending on the speed of the

playback selected.

■

playback

FF 2X

FF 4X

FF 8X

FF 20X

PLAY

Press "PLAY" button, the speed will go back to standard.

2. Press the “FR”

button during playback. Each time this button is pressed, the unit will go

into a rapid reverse playback mode. This will be shown on the LCD, depending on the speed of the

playback selected.

■

playback

FR 2X

FR 4X

FR 8X

FR 20X

PLAY

Press “PLAY” button, the speed will go back to standard.

NEXT TRACK OR PREVIOUS TRACK (DVD/MP3/CD)

1. Press the "NEXT"

button during playback.

■

MP3/Audio CD

The player will skip forward to the next track each time the button is pressed. "NEXT" will be

displayed on the LCD screen.

■

DVD

The player will skip forward to the next title/chapter each time the button is pressed.

2. Press the "PREV"

button during playback.

■

MP3/Audio CD

The player will skip to the beginning of the previous track each time the button is pressed.

"PREVIOUS" will be displayed on the LCD screen.

■

DVD

The player will skip to the beginning of the previous chapter each time the button is pressed.

PLAY/PAUSE (DVD/MP3/CD)

1. Press the "PLAY/PAUSE"

button, during playback. "PAUSE" will display on the LCD. The play-

er is placed in the pause mode.

2. Press the "PLAY/PAUSE"

button again. "PLAY" will momentarily display on the LCD. The

player returns to normal playback.

STOP (DVD/MP3/CD)

1. During playback, when the "STOP"

button is pressed,the playback will stop. “PRE STOP” will

button to continue playback from the point where

display on the LCD. Press the "PLAY/PAUSE"

the "STOP"

button was pressed.

2. During playback, if the "STOP"

the "PLAY/PAUSE"

button is pressed twice. "STOP" will display on the LCD. Press

button to resume playback from the beginning.

SELECTING A TRACK OR CHAPTER

Selecting tracks or chapters can be accomplished by either using the remote or front mounted con-

trols. These controls allow the operator to skip over undesirable tracks or repeat a particular track.

When playing a DVD, press the numeric buttons on the menu or title page to select tracks. During

DVD playback, you can input the desired title number directly.

MP3 AND JPEG PLAYBACK ON CD OR MEMORY CARD

Place a MP3, or JPEG disc or memory card into the DVD player. The player will search the media for

the saved directories and files. It will automatically go to the first directory saved and play or dis-

play the first file in that directory.

By using the arrow and ENTER buttons on the DVD player or the remote you can navigate and select

the directories (left side of the screen), or the file (right side of the screen).

When the disc or memory card contains JPEGs press the "PLAY/PAUSE"

button to present these

in slide show mode (displays each JPEG for a few seconds before advancing to the next JPEG). Press

the "PLAY/PAUSE"

buttons

button to pause the slide show at a photograph of interest. Use the arrow

/ on the remote (or their equivalent on the DVD player) to change the

ꢀ

orientation of the photograph. Pressing the PROGRAM button on the remote as the slide show is

being presented will change the “wipe” as each JPEG is displayed (there are 16 choices to from,

including RANDOM and NONE [off]).

The bottom of the screen will display the contents of the media - music

icons. For example if a memory stick contains MP3 and JPEG files but does not contain any video

files, the music and camera icons will appear white, but the video icon will appear dark. If a

, camera

, video

file is playing or displaying, the icon associated with that file will turn RED.

PLAYBACK PROGRAMMING

Press the PROGRAM button on the remote to display the Track (T)/Chapter (C) programming menu

screen. This allows you to selected those items on a DVD, MP3, or JPEG that you wish to view or lis-

ten. Use the arrow navigation keys on the remote to enter the Track and Chapter numbers, and then

navigate down to PLAY and press the ENTER button on the remote control.

The program will be retained only as long as power is on to the monitor or the disk or memory stick

that is being programmed is mounted in the system.

For MP3 or JPEG files the Track corresponds to the folder and the Chapter corresponds to the play

or viewing selection(s) desired within that folder.

PROG

--:--

PLAY

CLEAR

For SVCD, VCD, or CD the programming menu below displays. These formats do not have Track and

Chapter.

PROG

[

]

[

]

[

]

[

]

PLAY

CLEAR

ADVANCED PLAYBACK (DVD/MP3/CD)

REPEAT MODE

■

MP3/Audio CD

When the “REPEAT” button is pressed:

REP ONE = The current track will be repeated.

FOLDER REP = The current folder will be repeated.

FOLDER = All the folders will be repeated.

■

DVD

When the “REPEAT” button is pressed:

CHAPTER REPEAT = The current chapter will be repeated.

TITLE REPEAT = After the DVD plays, the current title menu will be displayed.

REPEAT OFF = The repeat mode will be switched off.

CAMERA ANGLE (DVD)

Some DVD discs may contain scenes, which have more than one viewing angle. For these discs, a

projector

icon will display in the upper left corner of the screen. The same scene can be viewed

from a different angle by using the "ANGLE" button.

1. During DVD playback, press the "ANGLE" button. A

icon along with “x/y” will appear.

“x” represents the current camera angle, and “y” represents the total number available camera

angles.

2. Press the "ANGLE" button until the preferred viewing angle is selected. The ANGLE selection

will cycle through all available camera angles.

NOTE: This function will only work on discs where multiple camera angles have

been recorded.

AUDIO FUNCTION (DVD)

During DVD playback, press the AUDIO button. An audio

icon will appear, along with the language

presently playing. Each press of the AUDIO button will cycle the DVD through each language available.

NOTE: The audio function works only for discs that have multiple audio soundtracks.

SUBTITLE (DVD)

You may change the subtitle language from the one selected at the initial playback setting to a dif-

ferent language, if available.

During DVD playback, press the "SUBTITLE" button. A screen

icon will appear along with

the status/language to be displayed. Each press of the "SUBTITLE" button will cycle to the next

available subtitle language, and then back to off.

Setup

Using the setup menus, you can do the initial setup, adjust the picture quality, and set the various

outputs. You can also set a language for the on-screen display.

1. Press the SETUP button on the remote to display the "Setup System". It will allow you to mod-

ify some of the player's basic settings. While using the setup screens disk play will auto pause.

2. Select one of the two main groupings of setups, SYSTEM, or LANGUAGE. Then press the ENTER

button.

To Cancel using Setup, press the SETUP button on the remote.

Accessing Setup Menus

(A) Press the SETUP button on the remote, the setup menu will appear as shown below.

(B) Press the

of the desired page, then press the

to activate that page; For example, if you want to setup the

video page, press to highlight the video icon, the video

page will be displayed on the screen as shown on the right.

arrow buttons to highlight the icon

or arrow button

button to highlight the desired option.

to select, the choices of that option

Press Enter or press

appear on the right.

(D) Press the Arrow buttons to highlight the Exit Setup

option, then press Enter or Setup again to exit Setup Menu.

System Setup

1. TV SYSTEM

According to the Color System of the TV, you can choose the

TV System.

NTSC: Choose this settings if your DVD player is connected to

a NTSC TV.

PAL: Choose this settings if your DVD player is connected to

a PAL TV.

AUTO: Choose this settings if your DVD player is connected

to a multi-system TV.

NOTE: If a DVD that is recorded in PAL is inserted while the set-up menu has NTSC

selected, it will automatically go to AUTO and play PAL, and return to NTSC

when the DVD is finished playing. If this setting is set to AUTO the picture

will flicker, roll, as the system determines what format DVD has been insert-

ed and then settle into the correct display mode for that DVD.

2. SCREEN SAVER

ON: Choose this setting to activate the screen saver.

OFF: Choose this setting to cancel the screen saver.

3. TV TYPE

4 : 3 PS (Pan & Scan): Choosing this setting if your DVD

player is connected to a normal ratio TV. You can fill the

movie to the entire screen of your TV. This might mean that

parts of the picture (the left and right edges) won't be seen.

4 : 3 LB (Letter Box): Choosing this setting if your DVD play-

er is connected to a normal ratio TV. You'll see the movies in

their original aspect ratio (height-to-width ratio). You'll see

the entire frame of the movie, but it will take up a smaller portion of the screen vertically. The movie

might appear with black bars at the top and bottom of the screen.

16 : 9 (Wide Screen): Choose this setting if your DVD player is connected to a wide screen TV.

4. PASSWORD

The password option is initialized locked, and you cannot set

the ratings limit or change the password. In order for the

Ratings feature work, the password mode must be turned on

(the lock icon will be locked

). If you want to access and

------

set the ratings limit, you will need to first enter the password,

(factory default is 1234), and then press Enter to confirm (the

lock icon will be unlocked

). To change the password, you

will be prompted for the old password, and then be prompted

for a new password. Ensure that the new password is record-

ed for future use.

5. RATING (PARENTAL SETTINGS)

The Rating setting is a rating viewing limit system. It works

with DVD discs that have been assigned a rating. This helps

you control the DVDs that your family watches.

1 G

2 PG

There are 6 rating options, these are: G, PG, PG-13, R, NC-17,

and ALL. Select level ALL to view all DVDs. The factory default

setting is ALL.

3 PG -13

4 R

5 NC -17

6 ALL

NOTE: If the password option is locked, you cannot set the ratings limit. The rat-

ing limit does not work if the password option is unlocked. Refer to the

Password discussion above.

6. DEFAULT

Choose this option to reset all the setup options (except for

password and rating setting) to default settings.

SCREEN SAVER

7. EXIT

Choose this option to exit the setup options.

Language Setup

The language setup options are listed below:

1. OSD LANGUAGE

The OSD (On Screen Display) Language Menu allows the user to sel-

ect the language for the on-screen display. Highlight the OSD

LANGUAGE option, and press the Arrow buttons to choose the

OSD language you prefer. The user can select English, Chinese,

German, Spanish, French, and Portuguese.

2. AUDIO LANG

The Audio Lang Menu allows the user to select the language

for the disc. Highlight the AUDIO LANG option, and press the

Arrow buttons to choose the audio language you prefer. Press

Enter to confirm. You can select English, Japan, French,

Spanish, Portuguese, Latin, German or Chinese.

3. SUBTITLE LANG

The Subtitle Lang Menu allows the user to select the lang-

uage for the subtitle of disc. Highlight the SUBTITLE LANG

option, and press the Arrow buttons to choose the subtitle

language you prefer. Press Enter to confirm. You can select

English, Japan, French, Spanish, Portuguese, Latin, German

and Chinese.

4. MENU LANG

The Menu Lang allows the user to select the language for the

menu. Highlight the MENU LANG option, and press the Arrow

buttons to choose the menu language you prefer. Press Enter

to confirm. You can select English, Japan, French, Spanish,

Portuguese, Latin, German or Chinese.

Installation Guide

PRECAUTIONS

1. This unit should be installed by an authorized Directed dealer.

2. When selecting a location to install this unit, be sure it does not interfere with the driver’s

ability to operate the vehicle or the driver's or passenger's safety.

3. This product is designed to operate with a 12V DC, negative ground battery system.

4. Disconnect the ground wire from the battery terminal prior to connecting the unit to the elec-

trical system.

NOTE: Head units with security codes will have to be reset after battery power is

restored.

5. The wiring from some other products or accessories might bear similar color code as this prod-

uct; however, they might be for other functions. Please refer to the electrical connection diagrams

of this product prior to installation to avoid improper connection.

6. Use proper connectors and insulation to prevent electrical damage to the unit.

7. Do not connect the yellow wire and red wire together of this product directly to the +12V.

Connect the red wire of this product to the ACC of the ignition key switch and yellow wire to +12V.

Failure to do so may result in discharge of the battery.

8. Only supplied accessories should be used to avoid damage to the unit during installation.

9. Ensure that the display monitor is suitably installed at a location, such that it will not obstruct

the rear view mirror and/or the air condition vents or operation of a sunroof.

10. Do not install this unit at a declining angle exceeding 30 degrees.

11. Do not install screws over the plane surface, which may affect the LCD screen deployment or

retract function.

ELECTRICAL CONNECTIONS

Power Cable (4–pin, one pin not used)

Color Code

Black

Function

This wire is the ground source for the monitor and DVD.

Accessory +12V switched power source for the monitor and DVD. This

wire supplies the main power to the system (0.5A fuse).

Red

Constant +12V power. This wire supplies power to the DVD for last

position memory (3A fuse).

Yellow

Dome Light Cable (3–pin)

Color Code

Function

Black

Yellow

Gray

This wire supplies the ground to the domelight circuit.

This wire supplies +12V constant power to the domelight circuit.

This wire connects to the (-) door trigger.

SIGNAL CONNECTIONS

Adapter Audio

Color Code

Red 1 (RCA)

White 1 (RCA)

Red 2 (RCA)

White 2 (RCA)

Red 3 (RCA)

Function

Audio - Right (Input)

Audio - Left (Input)

Audio - Right (Input)

Audio - Left (Input)

Audio - Right (Output)

Audio - Left (Output)

White 3 (RCA)

Adapter Video

Color Code

Function

Yellow 1 (RCA)

Yellow 2 (RCA)

Yellow 3 (RCA)

Video - In (V-IN 1)

Video - In (V-IN 2)

Video - Out (V-OUT 1)

Adapter IR

In addition each IN 2 and IN 1 grouping has an IR output jack which passes the remote control com-

mands to the device (VCR, CD player, TV tuner or other devices) connected to this input.

TYPICAL WIRING DIAGRAM

RED–Ignition

YELLOW–12V Constant

BLACK–Ground

A/V

OUTPUT 3

A(R) A(L)

OUT

IN2

A(L) A(R)

IN1

A(L) A(R)

Wireless

Headphones

A/V

SOURCE 2 SOURCE 1

YELLOW–12V Constant

BLACK–Ground

GRAY (-) Door Trigger

Installation Procedure

1. Identify the polarity of the dome light circuit and set the switch on the cable connection side

of the overhead monitor housing to match the vehicle’s door trigger polarity. Factory default posi-

tion for this switch is Negative. This switch is marked with the following instruction label.

ꢁ

Positive

Trigger Door

Switch

ꢂ

Negative

Trigger Door

Switch

Grey: Door Switch Yellow: +12V Black: Ground

Dome Light Wiring

2. Test fit the overhead monitor system on the ceiling of the vehicle, verifying it is not going to

interfere with the safe operation of the vehicle and is physically safe for the driver and passenger(s).

3. Once the mounting location of the overhead monitor system has been determined, carefully

mark the location with masking tape.

4. Lower the vehicle's headliner down to see if a roof support beam is available to screw the

mounting bracket to. If a support beam is not available to screw into, use a ¾" piece of plywood

cut to the appropriate size. Attach the plywood to the roof of the vehicle using silicone allowing

adequate drying time before proceeding.

5. Screw the mounting bracket in the vehicle. DOUBLE CHECK THE LENGTH OF THE SCREWS PRIOR

TO MOUNTING THE BRACKET, TO PRECLUDE PENETRATION OF THE VEHICLE’S ROOF.

Roof Beam Support

Optional Spacer Material

(Installer Provided)

Metal Bracket

Screws

(not included)

Screws

(Included)

6. Cut a 1" hole in the headliner along the backside of the mounting bracket for the cables to

pass through.

7. Route cables through the hole to the predetermined location of the AV source(s).

8. Identify the dome light wires in the vehicle and connect them to the corresponding dome light

wires on the overhead monitor system. Ensure the domelight switch is in the correct position.

9. Plug in the AV, DIN and power cables into the overhead monitor system.

10. Carefully hold the overhead monitor system to the mounting bracket aligning the mounting

holes while screwing in the screws. (Make sure the wires and cables are not in the way while mount-

ing the monitor).

11. Ground the Black wire of the power cable to a clean ground spot.

12. Connect the Yellow wire of the power cable to the battery positive terminal.

13. Connect the Red wire of the power cable to the Accessory wire in the ignition harness.

NOTE: Make sure you keep the ground wire of the monitor and video source as short

as possible to prevent unwanted audio noise pickup from the vehicle’s systems.

System Wiring Diagram Example

VCR

AUDIO AMPLIFIER

YELLOW

BATTERY (+12V)

Video In

BLACK (GROUND)

OUT

Power

RED (ACC)

DVD

TV Tuner

YELLOW

BLACK (GROUND)

+12V CONSTANT

GRAY (DOOR SWITCH)

IR Transmitter

Troubleshooting

No Picture

Press the POWER (source) button (or the

on and the proper source input is selected.

button on the remote) to make sure the monitor is

If the DVD menu appears, check the source unit.

If no DVD menu appears, check all fuses and power connections to the model. Inspect the connect-

ing cables for any fraying or breakage.

No Sound

If acquiring signal from another remote device (e.g. DVD player or CD player) ensure the device is

setup correctly.

The DVD player is in pause, slow motion, fast forward, or fast reverse mode. Place player in play

mode.

Picture Rolls

Check that the T.V. type setting is correct for the monitors and DVDs being used. PAL video often

rolls on NTSC monitors.

With a DVD player and a widescreen DVD disc, there are black bars on the screen

Change the TV display mode to "WIDE" in the DVD player's setup menu. After changing this setting,

if there are still black bars, press the MODE button on the remote control.

With a widescreen 16:9 monitor, I have black bars on the screen

Change the TV display mode to "Wide".

The Remote does NOT Function

Are there obstacles obstructing the view between the monitor and the remote.

The distance between the remote and monitor is too great.

The remote is not being pointed at the IR receiver on the LCD screen.

The batteries in the remote are weak.

DISC does NOT Play

Parental code is set lower than than allowed by the DVD mounted.

Ensure the disk is mounted in the player with the correct orientation (shiny side up).

The disk is warped.

The player cannot play certain formats (see the beginning of this manual).

The region code on the DVD does not match the player.

Moisture condensation has occurred within the player. Leave the unit on and the disc access cover

open and try again after about 30 minutes.

The disc has not been properly finalized (formatted) when recorded. Refer to your manual that came

with your disc authoring equipment.

Unit does NOT Display or Operate Correctly

Press Reset button located on the monitor along side the DVD player. This resets all of the system,

except for the Password and Parental Level setting.

Specifications

System

Laser

Semiconductor laser

NTSC, PAL

Signal Formats

Audio Characteristics

Frequency Response

DVD Video (PCM@ 96kHz)

20 Hz - 40 kHz 1dB

20 Hz - 20 kHz 1dB

DVD Video (PCM@ 48kHz)

Signal-to-Noise Ratio

Harmonic Distortion

Dynamic Range

90dB

0.01%

DVD Video

95dB

Outputs (A/V Switchbox)

Audio (phono jacks)

Video (phono jack)

2 Vrms

1 V p-p @75 ohms

Inputs (A/V Switchbox)

Audio (phono jacks)

Video (phono jack)

General

2 Vrms

1 V p-p

Power Requirements

Power Consumption

Dimensions

14.4 VDC, 3.35 amps

42.6 watts

345 mm x 65 mm x 282 mm

(length/height/width)

13.6 in. x 2.6 in. x 11.1 in.

(length/height/width)

Mass

2.3 kg

5 lbs

Operating Temperature

Operating Humidity

0°–50°C

10% to 90%

32°–120°F

NOTE: Specifications and design are subject to change without notice.

The company behind this system is Directed Electronics, Inc.

Since its inception, Directed has had one purpose, to provide consumers with the finest vehicle security, car stereo

products, rear seat entertainment, and accessories available. The recipient of more than 20 patents in the field of

advanced electronic technology, Directed is ISO 9001 registered.

Quality Directed Electronics products are sold and serviced throughout North America and around the world.

Call (800) 274-0200 for more information about our products and services.

Directed^®is committed to delivering world-class quality products

and services that excite and delight our customers.

Directed Electronics, Inc.

Vista, CA 92081

www.directed.com

N82901 03-05

Aiphone Car Video System MYH CUB User Manual
Aiphone KB MV2 User Manual
Canon 2544A003 User Manual
Canon Elura 10 User Manual
Canon MVX40i User Manual
Casio EXILIM ZOOM EX Z90 User Manual
Casio FX 9750GII User Manual
Huey Chiao HCB25 User Manual
JBL AS6 User Manual
JVC GR DVM801 User Manual