Daewoo 65M200 User Manual

PROJECTION MONITOR

Operating Guide for

51M200, 65M200, 51M200A

IMPORTANT SAFETY INSTRUCTIONS ................................................................................ 2-3

FIRST TIME USE .................................................................................................................. 4-19

THE REMOTE CONTROL .................................................................................................. 20-30

ON-SCREEN DISPLAY........................................................................................................ 31-52

CARE OF YOUR ASPECT PROJECTION MONITOR AND REMOTE CONTROL ..................53

USEFUL INFORMATION .................................................................................................... 54-57

INDEX ........................................................................................................................................58

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment

Follow all warnings and instructions marked on this Projection

Monitor.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

15. Projection Monitors are designed to comply with the

recommended safety standards for tilt and stability.

Do not apply excessive pulling force to the front, or top,

of the cabinet which could cause the product to over-

turn resulting in product damage and/or personal

injury.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accor-

dance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use the attachments/accessories specified by the

manufacturer.

16. Follow instructions for wall, shelf or ceiling mounting as

recommended by the manufacturer.

17. An outdoor antenna should not be located in the vicin-

ity of overhead power lines or other electrical circuits.

18. If an outside antenna is connected to the receiver be

sure the antenna system is grounded so as to provide

some protection against voltage surges and built up

static charges. Section 810 of the National Electric

Code, ANSI/NFPA No. 70-1984, provides information

with respect to proper grounding for the mast and sup-

porting structure, grounding of the lead-in wire to an

antenna discharge unit, size of grounding connectors,

location of antenna-discharge unit, connection to

grounding electrodes and requirements for the ground-

ing electrode.

ANTENNA

LEAD IN

WIRE

GROUND

CLAMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

12.

Use only with the cart, stand, tripod,

bracket, or table specified by the man-

ufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination

to avoid injury from tip-over.

ELECTRIC

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUNDING CONDUCTORS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250 PART H)

NEC NATIONAL ELECTRICAL CODE

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

Note to the CATV system installer: This reminder is

provided to call the CATV system installer’s attention to

Article 820-44 of the NEC that provides guidelines for

proper grounding and, in particular, specifies that the

cable ground shall be connected to the grounding sys-

tem of the building, as close to the point of cable entry

as practical.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into apparatus, the apparatus has been

exposed to rain or moisture, does not operate normal-

ly, or has been dropped.

Disposal of this product may require specific

instructions pertaining to your resident state. For

disposal or recycling information, please contact

your local authorities or the Electronic Industries

Alliance: www.eiae.org.

Do not place any objects on the top of the

Projection Monitor which may fall or cause a child

to climb to retrieve the objects.

Projection Monitor’s are heavy and can mark or damage floor surfaces (especially wood flooring) if moved improperly.

Do not slide or force Projection Monitor into position.

PREVENTION OF SCREEN BURN

This Wide Screen Projection Monitor is designed to display wide screen pictures. Images should be viewed mostly in wide screen

format or zoomed to fill the screen with moving pictures. Use of side panels, top and bottom panels of standard picture formats

should only be 15% of your total viewing time to prevent uneven aging of the phosphors. Phosphors in the lighted area of the pic-

ture will age more rapidly than the gray areas. Continuous on-screen displays such as video games, stock market quotations,

computer generated graphics, and other fixed (non-moving) patterns can cause permanent damage to Projection Monitors. Such

“SCREEN BURNS” constitute misuse and are NOT COVERED by your ASPECT Factory Warranty.

Lead Notice

This product contains lead. Dispose of this product in accordance with applicable environmental laws. For product recycling and

disposal information, contact your local government agency or the Electronic Industries Alliance at www.eiae.org (in the US) or

the Electronic Product Stewardship Canada at www.epsc.ca (in Canada). FOR MORE INFORMATION, CALL 1-800-488-2244.

ACCESSORIES

Check to make sure you have the following accessories before disposing of the packing material.

REMOTE CONTROL

HL02251

“AA” BATTERIES

POWER

CBL/SAT DVD/VCR

SWAP PIP MODE

PIP

FREEZE

C.C.

DAY/NIGHT

SELECT

EXIT

LAST CH

MUTE

VOL

ANT

INFO

VID1

VID2

VID3

SIZE

VID4

SLEEP

REC

VID5

CLU-433OUG

1. Remote Control Unit is either CLU-4330UG (Part No. HL02251).

2. Two “AA” size, 1.5V batteries (For Remote Control Unit).

REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT

1. Open the battery cover of the remote control by pushing the notched part of the cover with your fingers and pulling the

cover off.

2. Insert two new “AA” size batteries for the remote control. When replacing old batteries, push them towards the springs

and lift them out.

3. Match the batteries to the (+) and (-) marks in the battery compartment.

4. Replace the cover.

BOTTOM VIEW

Lift up on tab to

remove back cover.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace with the same or equivalent type.

HOW TO SET UP YOUR NEW HITACHI PROJECTION MONITOR

LOCATION

Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location

selected allows a free flow of air to and from the perforated back cover of the set.

To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the Projection Monitor where

temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc.

VIEWING

The major benefit of the ASPECT Projection Monitor is its large viewing screen. To see this large screen at its best, test various locations

in the room to find the optimum spot for viewing.

The best picture is seen by sitting directly in front of the Projection Monitor and about 10 to 18 feet from the screen. Picture brightness

decreases as the viewer moves to the left and right of the receiver.

During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the

reflection or the Projection Monitor can be located in a different section of the room.

If the Projection Monitor’s audio output will be connected to a Hi-Fi system’s external speakers, the best audio performance will be

obtained by placing the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture

screen center. For best stereo separation, place the external speakers at least four feet from the side of the Projection Monitor, place

the surround speakers to the side or behind the viewing area. Differences in room sizes and acoustical environments will require some

experimentation with speaker placement for best performance.

20'

4" Minimum

BEST

HORIZONTAL

BEST

VERTICAL VIEWING

ANGLE

10'

15'

20'

VIEWING ANGLE

4" Minimum

10'

15'

20'

CAUTION: Magnetic fields, such as those of external speakers, may cause the picture to distort if they are placed too

close to the Projection Monitor. Move the magnetic field source away from the Projection Monitor until there is

no picture distortion.

HOOK-UP CABLES AND CONNECTORS

Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors.

For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell

audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output

and input connector types required by the various components and the length of each cable.

Phono Connector

S-Video (Super Video) Connector

Used on all standard video and audio cables which

connect to inputs and outputs located on the Projection

Monitor’s rear jack panel and front control panel.

This connector is used on camcorders, VCRs and laser-

disc players with an S-Video feature in place of the

standard video cable to produce a high quality picture.

Digital Visual Interface (DVI) Connection Cable

This cable is used to connect external devices with

DVI-HDTV output capability. It delivers digital video in

its native format. Audio information is carried sepa-

rately.

FRONT PANEL CONTROLS

PULL

ASPECT

POWER

PULL

ASPECT

POWER

ቦ

ቩ

AUDIO

VOL-

VOL+

INPUT

EXIT

INPUT 5

SELECT

MAGIC FOCUS

VIDEO L/MONO

S-VIDEO

CURSOR

ባ

ቢ

ቤ

ብ

ቧ

ቨ

ቢ MENU/SELECT button

This button allows you to enter the MENU, making it possible to set Projection Monitor features to your preference without using

the remote. This button also serves as the SELECT button when in MENU mode.

ባ INPUT/EXIT button

Press this button to select the current VIDEO: 1, 2, 3, 4, 5. Your selection is shown in the top right corner of the screen. This button

also serves as the EXIT button when in MENU mode.

NOTES: Your remote control does not have an INPUT button. To change to video inputs, press VID1~VID5 buttons depending

on your choice (see page 22).

ቤ CURSOR UP/DOWN buttons

These buttons serve as the cursor down (̄) and up (̆) buttons when in MENU mode.

ብ VOLUME level

Press these buttons for your desired sound level. The volume level will be displayed on the Projection Monitor screen. These

buttons also serve as the cursor left (̇) and right (̈) buttons when in MENU mode.

ቦ POWER button/POWER LED

Press this button to turn the Projection Monitor on or off. This LED light is ON during normal operation.

ቧ MAGIC FOCUS

Use this button to automatically adjust your picture quality to optimum performance (see page 46). The Magic Focus button will not

work when adjustment mode is set to manual (see page 47).

ቨ FRONT INPUT JACKS (INPUT 5)

Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantly view your favorite show or new recording.

Press the INPUT button until VIDEO: 5 appears in the top right corner of the Projection Monitor screen. If you have mono sound,

insert the audio cable into the left audio jack.

ቩ IR RECEIVER Sensor

When using the remote control, point it towards the IR receiver for best response.

FRONT PANEL JACKS AND CONNECTORS

The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following

examples:

-AUDIO-

INPUT 5

S-VIDEO

L/MONO

S-VIDEO

VIDEO

L/MONO

MAGIC FOCUS

NOTE:

1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture

may be abnormal.

2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable.

3. If you have a mono VCR, insert the audio cable into the left audio jack of your Projection Monitor.

REAR PANEL JACKS

IMPORTANT:

This is a monitor only product. No TV or Cable tuner is included.

ቢ

ቧ

ቦ

DVI-HDTV

P_B

P_R

INPUT 1

(MONO)/L

AUDIO

P_B

P_R

Y/VIDEO

INPUT 2

(MONO)/L

AUDIO

(MONO)/L VIDEO

S-VIDEO

INPUT 3

INPUT 4

AUDIO

TO HI-FI

VIDEO

MONITOR

OUT

AUDIO

ቤ

ባ

ብ

ቢ Audio/Video Inputs 1, 2, 3 and 4

The VID1~VID4 buttons will select each video source each time they are pressed. Use the audio and video inputs to connect

external devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (If you have mono sound, insert the audio cable

into the left audio jack.)

NOTE:

You may use VIDEO or S-VIDEO inputs to connect to INPUT 3 and 4, but only one of these inputs may be used at a

time.

ባ MONITOR OUT

These jacks provide fixed audio and video signals which are used for recording. Use the S-VIDEO Output for high quality video

output.

NOTE:

S-VIDEO Output may be used for recording, only when the input is of S-VIDEO type.

ቤ AUDIO TO HI-FI Output

These jacks provide variable audio output to a separate stereo amplifier. With this connection, the audio to the stereo can be

controlled by the television’s main volume.

ብ S-VIDEO Inputs 3 and 4

Inputs 3 and 4 provide S-VIDEO (Super Video) jacks for connecting equipment with S-VIDEO output capability.

REAR PANEL JACKS

ቦ Component: Y-P_BP_RInputs

Inputs 1 and 2 provide Y-P_BP_Rjacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may

use composite video signal for INPUT:2.

NOTES: 1. Do not connect composite VIDEO and S-VIDEO to Input 3, 4 or 5 at the same time. S-VIDEO has priority over VIDEO

input.

2. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the

Monitor’s P input and the components R-Y output to the Monitor’s P input.

3. Your component outputs may be labeled Y-C C . In this case, connect the component C output to the Monitor’s

B R

input and the component C output to the Monitor’s P input.

4. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-P P inputs. (See page 34)

B R

5. To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-P P jacks.

B R

6. Input 2 (Y/VIDEO) can be used for composite video or component video input.

ቧ DVI-HDTV Input (Input 1)

Use this DVI-HDTV Input for your external devices with DVI-HDTV output such as a Set-Top-Box, high-band DTV decoders, DVD

players and D-VHS with Digital Content Protection.

NOTES: 1. Only DTV format such as 1080i, 720p, 480i and 480p are available for DVI-HDTV input.

2. The DVI-HDTV input is NOT compatible when used with a DVD player from a personal computer.

3. When connecting a Set-Top-Box with a copy-protect digital out terminal, a high definition picture can be displayed

on the screen in its digital form.

REAR PANEL CONNECTIONS

TYPICAL FULL-FEATURE SETUP

DVI-HDTV

Connect only 1 component to each input jack.

NOTE:

2. Follow connections that pertain to your personal entertainment system.

3. Composite video signal can be input to Input2~Input5.

4. Cables are not included with the purchase of this Projection Monitor.

TIPS ON REAR PANEL CONNECTIONS

•

S-VIDEO and DVI-HDTV connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use

these connections in place of the standard video connection if your device has this feature.

•

If your device has only one audio output (mono sound), connect it to the left audio jack on the Projection Monitor.

Refer to the operating guide of your other electronic equipment for additional information on connecting your cables.

You may use VIDEO or S-VIDEO inputs to connect to Input 3, Input 4 or Input 5, but only one of these may be used at a time.

Connect only 1 component (VCR, DVD player, camcorder, etc.) to each input jack.

COMPONENT: Y-P P (Input 1 & 2) connections are provided for high performance components, such as DVD players and

B R

set-top-boxes. Use these connections in place of the standard video connection if your device has this feature. Input 2 accepts

both composite or component video signals.

•

Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the Monitor’s P

input and the components R-Y output to the Monitor’s P input.

Your component outputs may be labeled Y-C C . In this case, connect the components C output to the Monitor’s P input

and the components C output to the Monitor’s P input.

B R

•

You may use composite video signal for Input 2~Input 5.

It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-P P inputs (see page 34).

B R

Y-P P

•

To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the

jacks.

B R

When using a DVI input from a Set-Top-Box, it is recommended that a 1080i or 720p input signal is used.

CONNECTING EXTERNAL AUDIO DEVICES

To control the audio level of an external audio amplifier with the remote control, connect the system as shown below.

REAR PANEL OF PROJECTION MONITOR

DVI-HDTV

NOTE:

To prevent damage to the speaker and distorted sound, set the volume control of the audio amplifier lower and adjust

the sound using the remote control of the Projection Monitor.

CONNECTING EXTERNAL VIDEO SOURCES

The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your

Projection Monitor is dependent on the model and features of each component. Check the owner’s manual of each component for

the location of video and audio inputs and outputs.

The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your

particular assortment of components and features. For best performance, video and audio cables should be made from coaxial

shielded wire.

Before Operating External Video Source

The input mode is changed every time the VID1~VID5 button is pressed as shown below. Connect an external source to the INPUT

terminal, then press the VID1~VID5 button as necessary to view the input source (see page 22).

NOTE:

When a video signal is not received from the VIDEO INPUT JACK on the back panel of the Projection Monitor

(i.e., VCR/laserdisc player, etc. is not connected or the video device is OFF), the Monitor will appear to be OFF.

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A MONAURAL AUDIO SOURCE TO INPUT1~INPUT5

1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the

Projection Monitor below.

2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack.

3. Press the VID4 button to view the program from the VCR or the laserdisc player. The VIDEO label disappears automatically after

approximately four seconds.

DVI-HDTV

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A STEREO SOURCE TO INPUT1~INPUT5

Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the

Projection Monitor below.

Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.

Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.

Press the VID4 button to view the program from the VCR or laserdisc player. The VIDEO label disappears automatically

after approximately four seconds.

DVI-HDTV

NOTE:

Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING AN S-VIDEO SOURCE TO INPUT 3, 4 AND 5

Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the

Projection Monitor below.

Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.

Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.

Press the VID4 button to view the program from the VCR or laserdisc player. The VIDEO label disappears automatically

after approximately four seconds.

DVI-HDTV

NOTE:

Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A COMPONENT SOURCE WITH DVI-HDTV CAPABILITY TO INPUT 1.

Connect the DVI connection cable from the output of the HDTV set top box or DVD player to the DVI-HDTV input as shown on

the Projection Monitor below.

Connect the cable from the AUDIO OUT R of the HDTV set top box or DVD player to the INPUT (AUDIO/R) jack.

Connect the cable from the AUDIO OUT L of the HDTV set top box or DVD player to the INPUT (AUDIO/L) jack.

Press the VID1 button to view the program from the HDTV set top box or DVD player. The VIDEO label disappears

automatically after approximately four seconds.

DVI-HDTV

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A COMPONENT SOURCE TO INPUT 1 OR 2: Y-P P .

B R

Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the

Projection Monitor below.

Connect the cable from the C /P OUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (P jack.

Connect the cable from the C /P OUT or R-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (P ) jack.

Connect the cable from the AUDIO OUT R of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/R) jack.

Connect the cable from the AUDIO OUT L of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/L) jack.

Press the VID1 button, to view the program from the Laserdisc/DVD player or HDTV set top box. The VIDEO label

disappears automatically after approximately four seconds.

DVI-HDTV

NOTE:

1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

2. See page 12 for tips on REAR PANEL CONNECTIONS.

THE REMOTE CONTROL

In addition to controlling all the functions on your ASPECT Projection Monitor, the new remote control is designed to operate dif-

ferent types of VCRs, CBL (Cable TV) converters, satellite receivers, DVD players, and other audio/video equipment. Basic oper-

ation keys are grouped together in one area.

To operate your Projection Monitor, point the remote control at the IR Receiver sensor (see page 7) of the Projection Monitor and

press the TV button. The remote will now control your Projection Monitor.

To operate your cable/satellite box, point the remote at the remote sensor of the cable/satellite box and press the CABLE/

SATELLITE (CBL/SAT) button. The remote will now control your cable/satellite box (see page 29 for instructions on how to

program the remote to control your cable box.)

To operate your DVD/VCR player, point the remote at the remote sensor of the DVD/VCR player and press the DVD/VCR but-

ton. The remote will now control your DVD/VCR player (see pages 28 and 30 for instruction on how to program the remote to

control your DVD/VCR player.)

POWER

These buttons allow the remote to control your

TV (Projection Monitor), VCR, DVD or cable/satellite

CBL/SAT DVD/VCR

box depending on which mode is chosen, as explained

above.

SWAP PIP MODE

FREEZE

PIP

C.C.

DAY/NIGHT

SELECT

EXIT

LAST CH

MUTE

VOL

INFO

ANT

TV (Projection Monitor) OR VCR/DVD BUTTONS

VID3

SIZE

VID4

SLEEP

VID1

VID2

VID5

When in TV (Projection Monitor) mode, these buttons,

REC

except the REC button, will select from five video input

sources. When inVCR/DVD mode, these buttons transmit

the chosen precoded VCR/DVD codes.

CLU-433OUG

HOW TO USE THE REMOTE TO

CONTROL YOUR PROJECTION MONITOR

POWER

ቢ PROJECTION MONITOR

POWER button

CBL/SAT DVD/VCR

SWAP PIP MODE

ባ _{PICTURE-IN-PICTURE}

FREEZE

PIP

C.C.

DAY/NIGHT

ቱ

ተ

MENU button

ቤ _{DAY/NIGHT button}

CLOSED CAPTION (CC) button

SELECT

EXIT

ብ _{SELECT, MENU, CURSOR buttons}

ቯ

ቮ

LAST CHANNEL (LAST CH) button

EXIT button

LAST CH

MUTE

ቦ _{VOLUME, MUTE buttons}

VOL

ቧ _{CHANNEL SELECTOR buttons}

ANT button

ቨ

INFO

ANT

ቭ

ቫ

INFO button

VID3

SIZE

VID4

VID1

VID2

VID5

SLEEP

REC

CLU-433OUG

SLEEP button

ቩ VID1~VID5 buttons

ቪ

SIZE button

ᕃ POWER button

Press this button to turn the Projection Monitor on or off when the remote is in TV (Monitor) mode.

ባ PICTURE-IN-PICTURE buttons

See separate section on pages 25, 26 and 27 for description.

ቤ DAY/NIGHT button

Press this button to toggle between Day and Night picture mode settings. Select Day for day time viewing with more brightness

and contrast to compete with room light. Select Night for night time viewing with less brightness and contrast for a more detailed

picture (see page 33 for settings changes).

ብ SELECT, MENU, CURSOR buttons

All the On-Screen Display features can be set or adjusted by using the CURSOR buttons, except for numeric entries.

The CURSOR will highlight functions or adjust and set different features. Press the CURSOR toward desired direction then press

the SELECT button to select.

HOW TO USE THE REMOTE TO

CONTROL YOUR PROJECTION MONITOR

ቦ VOLUME, MUTE button

Press the VOLUME up (̆) or down (̄) button until you obtain the desired sound level.

To reduce the sound to one half the normal volume (SOFT MUTE), press the MUTE button. Press the MUTE button again to turn

the sound off completely (MUTE). To restore the sound, press the MUTE button one more time, or press the VOLUME Up (̆) but-

ton.

MUTE

Volume

Soft Mute 8

Mute

Closed Captioning will display when MUTE/SOFT MUTE is on and Closed Caption is set to AUTO (See page 52).

ቧ CHANNEL selector buttons [Cable Box/Satellite Receiver (CBL/SAT)Mode Only]

These buttons are only applicable when the remote control is in CBL/SAT mode.

CHANNEL selector buttons are used to select channels, lock access code, etc.

Enter one, two, or three numbers to select channels. Enter “0” first for channels 1 to 9, or simply press the single digit channel you

wish to tune then wait a few seconds for the device to tune. For channels 100 and above, press the “1” button, wait until two dash-

es appear next to the channel display on your Projection Monitor, then enter the remaining two numbers using the number buttons.

Channel selection may also be performed by pressing CH up (̆) or down (̄).

ቨ ANTENNA button [Satellite Receiver (SAT) Mode Only]

The ANT button is only applicable when the Remote Control is in SAT mode.

ቩ VID1 ~ VID5

When the remote control is in TV (Monitor) mode, press these buttons to directly select the video input sources between the five

video inputs. When the remote control is in DVD/VCR mode, these buttons will control the DVD or VCR, and execute the secondary

function labeled.

HOW TO USE THE REMOTE TO

CONTROL YOUR PROJECTION MONITOR

ቪ SIZE button

Press this button to quickly change the picture format SIZE ratio.

Depending on the input signal, the picture format ratio allows you to adjust the images through the following options.

4:3 Standard

4:3 Expanded

Use this size mode to display conventional (4:3) images. Side panels (gray areas) are placed to the

left and right of the image to preserve the original size ratio of the source. Note: Use this mode for

only 15% of your total viewing time to prevent uneven aging of the phosphors. Phosphors in the lighted

area of the picture will age more rapidly than the black areas.

use this size mode to display conventional (4:3) sources by linearly increasing image expansion from

the center towards the edges of the display area in order to fill it.

4:3 Zoom1/Zoom2

16:9 Standard

Use these size modes to zoom in on conventional (4:3) sources.

Use this size mode to display 16:9 sources like HDTV and DVD’s preserving the original 16:9 aspect

ratio.

16:9 Zoom

Use this size mode to zoom 16:9 images.

(1) 480i/NTSC

4:3 INPUT

4:3 STANDARD

4:3 EXPANDED

4:3 ZOOM1

4:3 ZOOM2

16:9 ZOOM

16:9 STANDARD

4:3 EXPANDED

(2) 480p INPUT with Video ID: Letter

4:3 INPUT

4:3 STANDARD

4:3 ZOOM2

4:3 ZOOM1

(3) 720p/1080i INPUT

16:9 STANDARD

16:9 ZOOM

16:9 INPUT

NOTE:

All five video inputs have independent Picture Format ratio settings.

HOW TO USE THE REMOTE TO

CONTROL YOUR PROJECTION MONITOR

ቫ SLEEP button

Show and set your SLEEP timer for up to 3 hours in 15 minute intervals.

_Zzzz--:--

ቭ INFO button

Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second

audio program (SAP), the time and CHANNEL ID.

When a COMPONENT

VIDEO: Y-P P Input

is connected to

VIDEO: 1.

YPBPR:1

B R

Time

3:32 PM

Video: 3

VID 3

Main Picture Source

}

Aspect

Mode

Vitual HD

S - IN: 3

When an S-VIDEO

Input is connected to

VIDEO: 3.

Day/Night

Mode

Day

4:3 Expanded

1080i

Sleep Timer

_Zzzz-:--

Closed

Captioning

ቮ EXIT button

When in MENU mode, this button will exit all On-Screen Displays.

ቯ LAST CHANNEL (LAST CH) button [Cable Box/Satellite Receiver (CBL/SAT) Mode Only]

This button is only applicable when iin CBL/SATmode.

Use this button to select between the last two channels viewed.

LAST CH

ተ C.C. button

Press this button to set the Closed Caption options to ON, OFF, and AUTO.

ቱ MENU button

The MENU button will start the On-Screen Display.

PICTURE-IN-PICTURE (PIP)

All Video inputs can be viewed as both the main picture and the sub-picture simultaneously. To select between main picture and PIP

sub-picture tuning, press the SWAP button on the remote. The green highlighted Video input display will move with every press of the

SWAP button. You can change your Video input when the green highlighted display is shown.

DVI-HDTV

POWER

CBL/SAT DVD/VCR

ቤ

ባ

ቢ

SWAP PIP MODE

FREEZE

PIP

DAY/NIGHT

ብ,ቦ

C.C.

SELECT

EXIT

LAST CH

MUTE

Use above connection to view VCR program as a sub-picture while viewing another program as main picture (VID 1, VID2, VID3,

VID5).

ቢ PIP button

Press the PIP button and a sub-picture will appear in one of the three different modes (POP, PIP or SPLIT), depending on the last

selection of the PIP mode. To change the PIP mode, use the PIP MODE button to cycle through the three different modes.

POP MODE PICTURE-IN-PICTURE

POP Mode PIP displays the sub-picture outside of the main picture. Use the CURSOR PAD (̆ or ̄) to move the sub-picture. This

feature is not available with a 1080i signal. Please refer to the PICTURE-IN-PICTURE MODES Table (see page 26).

Video: 3

Main Picture

Video: 3

PIP

Sub Picture

NOTES: 1. In POP mode, CURSOR ̆ and ̄ will move the sub-picture up/down.

2. Only Sound from the main picture can be heard.

PIP MODE PICTURE-IN-PICTURE (This feature is only available with a 1080i signal)

To prevent a pattern burn, occasionally move the sub-picture using the CURSOR ̇, ̈, ̆, ̄.

Main Picture

Sub Picture

PIP

PICTURE-IN-PICTURE (PIP)

SPLIT MODE PICTURE-IN-PICTURE

Split Mode PIP displays the main picture and sub-picture evenly on the screen.

Video: 3

Video: 4

Sub Picture

Main Picture

ባ SWAP button

If you wish to enable the Audio from the Main Picture to the Sub-Picture, press the SWAP button.

Video: 3

Video: 4

Video: 3

SWAP

SPLIT

Green Highlight

NOTE: The SWAP button will only operate in POP/SPLIT/PIP mode.

ቤ PIP MODE button

To change between the different PIP modes (POP, PIP or SPLIT) press the PIP MODE button when PIP is ON. Each press of

this button will change PIP to a different mode.

Video: 3

Video: 4

Video: 3

PIP MODE

Video: 4

PIP MODES will depend on the type of input signal.

PICTURE-IN-PICTURE (PIP) MODES

POP

YES

PIP SPLIT

480i

YES

480p

720p

1080i

YES

PICTURE-IN-PICTURE (PIP)

ብ FREEZE button (With PIP ON)

If you wish to freeze the sub-picture, press the FREEZE button. This is convenient when trying to write down the address for

a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the FREEZE button

again.

NOTE:

When PIP is on, the FREEZE function will only operate when POP/PIP/SPLIT mode is chosen.

ቦ FREEZE button (with PIP OFF)

Press the FREEZE button to freeze the picture, depending on the PIP mode selected (POP Sub Freeze, SPLIT or STROBE).

To change FREEZE modes, use the PIP MODE button to cycle through the three different modes.

POP SUB FREEZE (with PIP OFF)

PIP should be in POP mode. Press the FREEZE button to freeze. Press the FREEZE button again to return to normal viewing.

Video: 3

Hot Springs Clay Mask

C/O John Doe

Run-Spa Retreat

P.O. Box 55512

FREEZE

Any Town, USA 98765

Check or

Hot Springs Clay Mask

C/O John Doe

Run-Spa Retreat

Money Order Only

1-800-555-1212

P.O. Box 55512

Any Town, USA 98765

Check or

Money Order Only

1-800-555-1212

SPLIT FREEZE(with PIP OFF)

PIP should be in SPLIT mode. Press the FREEZE button to freeze the picture you are currently viewing (only the right sub-picture

will freeze). Press the FREEZE button again to return to normal viewing.

Sub Picture

Main Picture

Video: 3

FREEZE

STROBE FREEZE(with PIP OFF)

Freeze Mode should be in STROBE Freeze. Press the FREEZE button to freeze three frames of the picture you are currently

viewing. Press this button again to return to normal viewing. This feature is useful for viewing a moving picture that has many details,

for example, a close play in a sporting event or a golf swing.

FREEZE

NOTES: Each freeze frame is delayed about 0.1 (1/10) second.

USING THE REMOTE TO CONTROL VCR FUNCTIONS

Operating the precoded function for your VCR.

This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your

VCR.

1. Turn ON your VCR.

2. Aim the remote control at the front of your VCR.

3. Press and release the DVD/VCR button to switch to VCR pre-coded mode.

4. Hold down the DVD/VCR button on the remote and enter the two digit preset code that matches your VCR, as shown below.

5. Aim the remote at the VCR and press the POWER button. The remote will turn off your VCR when the correct two digit preset code

is entered. When this occurs, the remote control is programmed for your VCR. If the VCR does not turn off, try a different two digit

preset code.

6. The remote will now control your VCR.

NOTES:

1. If your VCR cannot be operated after performing the

POWER

above procedures, your VCR’s code has not been

precoded into the remote.

CBL/SAT DVD/VCR

ቢ

2. In the unlikely event that your VCR cannot be operated

after performing the above procedures, please consult

your VCR operating guide.

SWAP PIP MODE

FREEZE

PIP

C.C.

DAY/NIGHT

3. The remote control will remember the codes you have

programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the

entire programming procedure as stated above.

SELECT

EXIT

ቤ

ቢ DVD/VCR Button

LAST CH

MUTE

This button allows the remote to control your VCR by set-

ting it to VCR mode.

ባ PRECODED VCR Buttons

VOL

These buttons transmit the chosen precoded VCR codes.

For some VCRs, you must press the RECORD button twice

to record a program.

ባ

ቤ EXCLUSIVE TV (Monitor) Buttons

These buttons are for operating the Projection Monitor.

INFO

ANT

VCR BRAND

CODE

Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Daewoo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Emerson . . . . . . . . . . . . . . . . . . . . . . . .20,21,22,23,24

Fisher . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34,37,38,39

Funai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

General Electric . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Goldstar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Hitachi . . . . . . . . . . . . . . . . . . . . .00,01,02,03,04,05,06

JVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18,49,50,51

Magnavox . . . . . . . . . . . . . . . . . . . . . . . . . . .12,13, 14

Mitsubishi . . . . . . . . . . . . . . . . . . . . . . . . . .27,28,29,30

NEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40,41

Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10,11

Philips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17,25,26

Scott . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Sharp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31,32

Shintom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .07,08,09

Symphonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Teknica . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

VID1

VID2

VID5

VID3

SIZE

VID4

SLEEP

REC

CLU-433OUG

MY VCR CODE IS:

NOTE:

Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR.

USING THE REMOTE TO CONTROL

CABLE/SATELLITE BOX FUNCTIONS

Operating the precoded function for your cable/satellite box.

This remote is designed to operate different types of cable/satellite boxes. You must first program the remote to match the remote sys-

tem of your cable/satellite box .

1. Turn ON your cable/satellite box.

2. Aim the remote control at the front of your cable/satellite box.

3. Press and release the cable/satellite (CBL/SAT) button to switch to cable/satellite pre-coded mode.

4. Hold down the CBL/SAT button on the remote and enter the two digit preset code that matches your cable/satellite box as shown

below.

5. Aim the remote at the cable/satellite box and press the POWER button. The remote will turn off your cable/satellite box when the

correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable/satellite box. If the

box does not turn off, try a different two digit preset code.

6. The remote will now control your cable/satellite box.

NOTES:

1. If your cable/satellite box cannot be operated after

POWER

performing the above procedures, your cable/satellite box

code has not been precoded into the remote.

ቢ

CBL/SAT DVD/VCR

SWAP PIP MODE

FREEZE

PIP

2. In the unlikely event that your cable/satellite box cannot

be operated after performing the above procedures,

please consult your cable/satellite box operating guide.

C.C.

DAY/NIGHT

3. The remote control will remember the codes you have

programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the

entire programming procedure as stated above.

SELECT

EXIT

ቤ

LAST CH

MUTE

VOL

ቢ CABLE (CBL/SAT) Button

ባ

This button allows the remote to control your cable/satellite

box by setting it to CABLE/SATELLITE mode.

ባ PRECODED CABLE/SATELLITE BOX Buttons

These buttons transmit the chosen precoded cable/satellite

codes.

INFO

ANT

ቤ EXCLUSIVE TV (Monitor) Buttons

ባ

These buttons are for operating the Projection Monitor.

VID1

VID2

VID5

VID3

SIZE

VID4

SLEEP

CABLE BRAND

CODE

REC

General Instrument . . . . . . . . . . . . . . . . . . . . . . . . . .17

Hamlin . . . . . . . . . . . . . . . . . . . . . . . . . . . .22,23,24,25

Jerrold . . . . . . . . . . . . . . . .00,01,02,03,04,05,06,07,21

Oak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26,27,28

Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . .18,19,20

Pioneer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13,14

Scientific Atlanta . . . . . . . . . . . . . . . . . . . . . . .08,09,10

Tocom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15,16

Zenith . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11,12

CLU-433OUG

SATELLITE BRAND

CODE

MY CABLE/SATELLITE

BOX CODE IS:

Ecostar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Hitachi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Hughes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30, 35

Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

NOTE:

Refer to instruction manual of the Cable/Satellite Box for operation of the buttons exclusively for the Cable/Satellite Box.

USING THE REMOTE TO CONTROL

DVD FUNCTIONS

Operating the precoded function for your DVD player.

This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of

your DVD player.

1. Turn ON your DVD player.

2. Aim the remote control at the front of your DVD player.

3. Press and release the DVD/VCR button to switch to DVD pre-coded mode.

4. Hold down the DVD/VCR button on the remote and enter the two digit preset code that matches your DVD player, as shown below.

5. Aim the remote at the DVD player and press the POWER button. The remote will turn off your DVD player when the correct two

digit preset code is entered. When this occurs, the remote control is programmed for your DVD player. If the DVD player does not

turn off, try a different two digit preset code.

6. The remote will now control your DVD player.

NOTES:

1. If your DVD player cannot be operated after performing

POWER

CBL/SAT DVD/VCR

the above procedures, your DVD player’s code has not

been precoded into the remote.

ቢ

SWAP PIP MODE

FREEZE

PIP

2. In the unlikely event that your DVD player cannot be

operated after performing the above procedures, please

consult your DVD player operating guide.

C.C.

DAY/NIGHT

3. The remote control will remember the codes you have

programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the

entire programming procedure as stated above.

SELECT

EXIT

LAST CH

MUTE

ቤ

ቢ DVD/VCR Button

This button allows the remote to control your DVD player by

setting it to DVD mode.

VOL

ባ PRECODED DVD Buttons

ባ

These buttons transmit the chosen precoded DVD codes.

ቤ EXCLUSIVE TV (Monitor) Buttons

These buttons are for operating the Projection Monitor.

INFO

ANT

VID1

VID2

VID5

VID3

SIZE

VID4

SLEEP

REC

DVD BRAND

CODE

Hitachi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53, 59, 60

Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Pioneer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Sanyo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

CLU-433OUG

MY DVD PLAYER CODE IS:

NOTE:

Refer to instruction manual of the DVD player for operation of the buttons exclusively for the DVD player.

ON-SCREEN DISPLAY (OSD)

1. Press MENU on the remote control to display the different features on your ASPECT Projection Monitor.

2. Press the CURSOR ̇, ̈, ̆ and ̄ to highlight a different feature, then press SELECT to choose.

3. Press EXIT on the remote control to quickly exit from a menu.

4. Press CURSOR ̇ or ̈ to access Favorite Channels menu.

SELECT

EXIT

This part of the screen shows

which selections are available.

Video

Audio

Aspect

Locks

Setup

Move

SEL

Sel

This part of the screen shows

which Remote Control buttons

to use.

PULL

ASPECT

POWER

ON-SCREEN DISPLAY (OSD)

Picture Mode

Select between the two picture modes; Day

and Night.

Contrast

Adjust contrast.

Adjust brightness.

Adjust color.

Adjust tint.

Adjust sharpness.

Set this to High for less intense color with more blue, set to Medium

for natural color, set to Standard for standard colors or Black and

White for more reddish color.

Brightness

Color

Tint

Sharpness

Color Temperature

Video

Black Enhancement

Edge Enhancement

Reset Video Settings

Color Management

Adjust shadow detail in dark screens.

Automatically enhances the edges between light and dark areas.

Choose to Reset Video settings.

Adjust and balance individual colors to make either deeper or more

pure according to preference.

Color Decoding

Auto Color

Adjust the percentage of Red, Green and Color according to

preference.

The AUTO COLOR function automatically monitors and adjusts the

color to maintain constant color levels even after a program or channel

changes. It also maintains natural flesh tones while preserving fidelity

of background colors.

Noise Reduction

Auto Movie Mode

Reduces conspicuous noise in the picture.

Turn ON/OFF the 3:2 Pulldown detection feature.

Treble

Bass

Balance

Adjust the treble.

Adjust the bass.

Adjust the balance.

Sound Enhancement

Internal Speakers

Perfect Volume

Loudness

Select SRS and BBE settings.

Select internal speakers to be “on” or “off”.

Adjust volume in fixed setting.

Adjust Loudness.

Audio

Mode

Choose the picture format aspect ratio.

Aspect

Change Access Code

Engage Lock

Movie Ratings

Change Lock access code.

Choose to lock channel, video input, and front panel.

Block various types of movies and video types based on motion

picture ratings.

TV Ratings

Block various types of movies and television programming based on a

parental guide ratings.

Locks

Setup

Canadian Ratings (ENG)

Canadian Ratings (FRN)

Block various types of movies and television programming based on

the Canadian ratings system.

Block various types of movies and television programming based on

the Canadian French ratings system.

Magic Focus Tune Up

Automatic and manual alignment of the red, green and blue colors to

make white.

Choose English, French, or Spanish text.

Set the Projection Monitor clock. It must be set before using the Lock

feature.

Label Video Inputs , VCR, DVD, etc.

Set tint and color coordinates for DTV programs.

Select between 1080i and 540p signal.

Set the gray side bars on/off when watching 4:3 signals in

standard mode.

Menu Preference

Set The Clock

Set The Inputs

Set The Color System

Set Virtual HD

Set Black Side Panel

Set Closed Captions

About Your TV

Feature to display dialogue/text.

Information display for this Projection Monitor.

VIDEO

Select VIDEO to adjust picture settings and improve picture quality. You can independently customize each of the

Video Inputs to your preference to increase viewing performance and pleasure depending upon the video program

being viewed. If RESET is selected, only the selected input will reset to initial conditions.

Video

Picture Mode

Use this function to choose from automatic picture settings to optimize your Projection Monitor’s performance.

Video

Audio

Aspect

Locks

Setup

SEL

Move

Sel

SELECT

Video: 3

Day

Video

Night

Picture Mode

100%

50%

Contrast

Brightness

50%

Color

Tint

Sharpness

50%

High

Color Temperature

Black Enhancement

Edge Enhancement

Reset Video Settings

Middle

High

Picture Mode

Day Night

SEL Return

Next/Prev

Select

SEL Return

Move

Use CURSOR ̇ or ̈ to highlight and select Picture Mode settings.

Function Day Night

Reset

Reset the video

menu settings on

current input

automatically to

Day Mode.

Contrast

100%

50%

45%

Brightness

Color

Tint

Center

50%

High

Middle

High

Off

Center

50%

Standard

Low

Sharpness

Color Temperature

Black Enhancement

Edge Enhancement

Auto Color

Low

Off

Noise Reduction

Off

Color Management

(Set User Colors)

Auto Movie Mode

Off

(3:2 Pulldown)

Press EXIT to quit menu or select PICTURE MODE to return to previous menu.

VIDEO

ANT A/B

Day

Video

Audio

Aspect

Locks

Setup

Move

Video

Picture Mode

Night

100%

50%

Contrast

Brightness

50%

Color

Tint

SEL

SELECT

Sel

Sharpness

50%

High

Color Temperature

Black Enhancement

Edge Enhancement

Reset Video Settings

Middle

High

SEL Return

Move

Use the CURSOR ̆ or ̄ to highlight the function to be adjusted.

Press the SELECT button to select the function settings.

Press the CURSOR ̇ or ̈ to adjust the function.

Press MENU to return to main menu.

Press EXIT to quit menu.

Contrast

Use this function to change the contrast between black and white levels in the picture.

Use this function to adjust overall picture brightness.

Brightness

Color

Use this function to adjust the level of color in the picture.

Tint

Use this function to adjust flesh tones so they appear natural.

Sharpness

Use this function to adjust the amount of fine detail in the picture. Sharpness function will be disabled

when Noise Reduction is ON.

Color Temperature

Black Enhancement

Edge Enhancement

Set this to High for cooler color with more blue, set to Medium for more natural color, set to Standard for

accurate color or set to Black/White for more reddish color.

Use this function to enhance the shadow detail in dark scenes using the settings off, low, middle and high.

Use this function to automatically enhance the edges between light and dark areas using the settings Off,

Low, Middle, and High.

NOTES: 1. If CONTRAST is selected, you are adjusting CONTRAST. The additional menu items BRIGHTNESS, COLOR, TINT,

and SHARPNESS can be selected and adjusted in the same manner.

2. It may be necessary to adjust TINT to obtain optimum picture quality when using the COMPONENT VIDEO Y-P P

B R

input jacks.

3. Each of the video inputs have their own independent settings.

VIDEO

This function allows you to Reset the Video Menu Settings of the present input and return it to the Day VIDEO

mode.

Reset Video

Settings

Ant A/B

Day

Video

Picture Mode

Video

Reset Video Settings

Night

100%

50%

Contrast

Select “Reset” to Return the Video

Menu Settings on this input to the

original factory settings.

Brightness

50%

Color

Tint

Reset

SELECT

Sharpness

50%

High

Color Temperature

Black Enhancement

Edge Enhancement

Reset Video Settings

Middle

High

Move

^SELReturn

Move

^SELSelect

Use CURSOR to highlight functions.

Press the SELECT button to select Reset Video Settings.

Use CURSOR ̄ to access other video settings.

You can customize each of the Video Inputs to your preference to increase viewing performance and pleasure, depending upon the

video program being viewed. If RESET is selected, only the selected Input will reset to the initial conditions as explained above.

If RESET is selected in Video:1 mode, only Video:1 mode will return to factory conditions.

Ant A/B

Day

Video

Color Management

Video

Picture Mode

Night

100%

50%

Color Decoding

Auto Color

Contrast

Off

Brightness

50%

Noise Reduction

Auto Movie Mode

Color

Tint

SELECT

Move

^SELSelect

Sharpness

50%

High

Color Temperature

Black Enhancement

Edge Enhancement

Reset Video Settings

Middle

High

Move

^SELSelect

Use this function to adjust and balance the listed individual colors to make them either deeper or more

pure depending on the user’s preference.

Color Management

Video

Color Management

Color Decoding

Auto Color

Set User Colors

Off

Magenta

Red

50%

Noise Reduction

Auto Movie Mode

Yellow

Green

Cyan

Move

^SELSelect

Blue

Reset

Move

^SELReturn

Use CURSOR to highlight function.

Press the SELECT button to select the User Colors setting. When the function has a “ͱ” in the box, it is ON.

Press CURSOR ̇, ̈, ̄and ̆ to highlight and adjust individual colors.

Use CURSOR to highlight and select “Reset” to return all colors to default settings.

NOTE:

When the Set User Colors box is not checked, the listed colors will be grayed out.

VIDEO

Use this function to adjust the percentage of Red, Green and Color according to the user’s preference.

Use TINT to adjust flesh tones so they appear natural.

Color Decoding

Video

Color Decoding

Color Management

Color Decoding

Auto Color

RGB

Off

Red

50%

Noise Reduction

Auto Movie Mode

Green

Color

Tint

SELECT

SEL Select

Move

Reset

SEL Return

Move

Use CURSOR to highlight function.

Press the SELECT button to select from 4 menu items.

Press CURSOR ̇, ̈, ̄ and ̆ to highlight and adjust Red, Green, Color and Tint.

Use CURSOR to highlight and select “Reset” to return all settings to default.

NOTE:

Color Decoding settings are independently stored in each of the 4 Color Temperature settings.

The AUTO COLOR function automatically monitors and adjusts the color to maintain constant color levels

even after a program or channel changes. It also maintains natural flesh tones while preserving fidelity of

background colors.

Auto Color

NOTE:

When using Component or DVI-HDTV input, Auto Color will not be available (grayed out).

The NOISE REDUCTION function automatically reduces conspicuous noise in the picture without

degrading picture quality. Set NOISE REDUCTION to OFF if the Projection Monitor experiences

picture blocking. When Noise Reduction is ON, Sharpness function is disabled (grayed out).

Noise Reduction

Auto Movie Mode

The Auto Movie Mode function turns ON or OFF the 3:2 PULLDOWN DETECTION SPECIAL FEATURE.

Theatrical movies are shot on film at 24 frames or still pictures per second, instead of 30 frames or 60 fields

like video. When film is transferred to video for Projection Monitor viewing, the disparity between the two

frame rates must be reconciled. This involves a process known as 3:2 pulldown.

When Auto Movie Mode is turned ON from the VIDEO menu, your ASPECT Projection Monitor will activate

the circuitry for this special feature to improve video performance when watching film based sources.

NOTES: 1. When using Progressive Scan Component or DVI-HDTV input (Ex. 480p, 720p and 1080i), Auto Movie Mode will not

be available (grayed out).

2. All Video settings are independent of each other based on it’s input (Input 1~5).

AUDIO

Audio

Select AUDIO to adjust the Projection Monitor to your preference and to improve the sound quality.

Audio

Treble

Video

Audio

Aspect

Locks

Setup

Move

45%

50%

Bass

Balance

Sound Enhancement

Internal Speakers

Perfect Volume

Loudness

Off

SEL

Sel

SELECT

SEL Return

Move

Press CURSOR ̆ or ̄ to select menu item.

Press CURSOR ̇ or ̈ to adjust the function.

Press EXIT to quit the MENU, or select AUDIO to return to the main menu.

NOTE:

If TREBLE is selected you are adjusting treble. The additional menu items Bass and Balance can be selected and

adjusted in the same manner.

This function controls the high frequency audio to all speakers.

Treble

Bass

This function controls the low frequency audio to all speakers.

This function will control the left to right balance of the Projection Monitor internal speakers.

Balance

Sound Enhancement See page 38.

This function is useful when setting up the external speakers.

ON - Select this feature if using the internal speakers only.

OFF - Select this feature if you prefer to use only speakers from a separate stereo system.

Internal Speakers

This function will automatically adjust volume so each channel and input has the same average volume

level.

Perfect Volume

Loudness

This function turns loudness ON or OFF. It will improve the quality of both low and high frequency sounds

when listening at low volume levels.

AUDIO

The following surround settings will reproduce the “live” sound you would hear in concert halls,

sports stadiums, movie theaters, etc. with only two speakers.

Sound Enhancement

Audio

Treble

Video

Audio

Aspect

Locks

Setup

Move

45%

50%

Bass

Balance

Sound Enhancement

Internal Speakers

Perfect Volume

Loudness

SRS

Off

SEL

Sel

SELECT

SEL Return

Move

To enter SOUND ENHANCEMENT, use CURSOR ̆ or ̄ to highlight then press CURSOR ̈ to select SOUND ENHANCEMENT of

your choice (Off, SRS, BBE and SRS and BBE).

Use the CURSOR to highlight your sound enhancement choice, and press SELECT to select your choice.

Based on the principles of the human hearing system, SRS technology delivers and exciting and realistic 3D Sound experience from

just two external speakers (or) the two internal speakers of your ASPECT Projection Monitor. If your ASPECT Projection Monitor is

connected to an external audio system, SRS will also create an incredible 3D sound experience from two speakers and even enhance

a complete multi-speaker surround sound system.

NOTES:

*SRS and the

Labs, Inc.

symbol are trademarks of SRS Labs, Inc. SRS technology is incorporated under license from SRS

Technology

Sound reproduction quality enhancement system. The BBE technology produces sound that is natural and crisp from just two speak-

ers (or) the two internal speakers of your ASPECT Projection Monitor. If your ASPECT Projection Monitor is connected to an external

audio system, BBE will also create an incredible crisp sound experience from two speakers. BBE brings to the listener’s ear a more

complete and accurate reproduction of the original performance. Each voice, speaking or singing, each instrument or sound effect is

presented with its attendant harmonics or partials more clearly audible. The ear can then more easily recognize the unique tonal col-

ors of each sound as though the sound was being produced live.

Licensed by BBE Sound, Inc. under USP5510752 and 5736897. BBE and BBE symbol are registered trademarks of BBE

Sound, Inc. Manufactured under license from BBE Sound, Inc.

NOTES:

ASPECT

Aspect Mode

Use this function to select the Picture Format Aspect Ratio (SIZE).

Video

Aspect

Audio

Aspect

Locks

Setup

Move

Mode

16:9 Standard

4:3 Standard

4:3 Zoom1

16:9 Zoom

4:3 Expanded

4:3 Zoom2

Auto Aspect

SEL

Sel

SELECT

Vertical Position

SEL Return

Move

Auto Aspect

Automatically adjust the Aspect Ratio depending on the input signal to fill the screen.

Press CURSOR ̆, ̄, ̇ and ̈ to select menu item.

Press the SELECT button to select. A “ͱ” in the box indicates that the feature is ON.

NOTES: 1. The Auto Aspect function is recommended on an input signal with VIDEO ID.

2. The Auto Aspect function is best used on composite video, S-Video, and 480i component signals.

3. See page 23 for Aspect Mode availability.

Vertical Position

This function allows you to select when aspect style is either 4:3 EXPANDED/ZOOM1/ZOOM2 or 16:9 ZOOM. Vertical position can be

changed with these modes. For example, it will be useful for centering the picture area at both the top and bottom of the picture with

480i/480P signal. Adjustable range is -10 (video center is toward bottom of screen) to +10 (video center is toward top of screen).

Press CURSOR ̆ or ̄ to select menu item.

Press CURSOR ̇ or ̈ to adjust the function.

Press EXIT to quit the MENU, or select ASPECT to return to the main menu.

NOTE:

Vertical Position will not be available in 4:3 Standard and 16:9 Standard modes.

LOCKS

This function is only available if used in conjunction with an external tuner. This function will block out

the picture and sound of the selected channel or video input. It can also be used to keep the Projection

Monitor from being viewed for a scheduled time period that you set.

Locks

The code to enter the Locks feature is a four digit secret code number. The factory preset code is 0000.

Use the number buttons to select secret code.

Video

Audio

Aspect

Locks

Please Enter Access Code

Setup

Move

SEL

SELECT

Sel

[ - - - - ]

[# Keys] Enter Code

Locks

Change Access Code

Engage Lock

Movie Ratings

TV Ratings

Canadian Ratings (Eng)

Canadian Ratings (Frn)

SEL Return

Move

Use CURSOR ̆ or ̄ to highlight function and then press SELECT button.

To change the secret code number, select Change Access Code. Enter a new four digit key number you prefer.

Select CHANGE ACCESS CODE to change the factory preset code (0000) to your preference.

When ENGAGE LOCK is selected, SET INPUT LOCK and SET FRONT PANEL LOCK can be set individually.

When SET INPUT LOCK is turned on, the picture and sound for all video inputs will be blocked out.

When FRONT PANEL LOCK is turned on, all buttons on the Front Panel will be deactivated, except the Power button.

When MOVIE RATINGS is selected, you can block various types of movies and video tapes based on motion picture ratings. Picture-

in-Picture will also be blocked automatically (see page 41).

When TV RATINGS is selected, various types of television programming based on a parental guide ratings will be blocked.

Picture-in-Picture will also be blocked automatically (see page 42).

Use CANADIAN RATINGS to block various types of movies and television programs based on the two rating systems used in

Canada that you feel may be inappropriate due to its content (see pages 43-44).

If you forget your secret code, use the factory code 7777 to erase your key number. This will reset the secret code number back to the

factory preset 0000.

Press EXIT to quit the menu or select LOCKS to return to previous menu.

LOCKS

Use MOVIE RATINGS to prevent viewing of any movie that you feel may be inappropriate due to

its content.

Movie Ratings

Locks

Change Access Code

Locks

Movie Ratings

Engage Lock

Status

Not Rated:

Movie Ratings

PG:

TV Ratings

Canadian Ratings (Eng)

Canadian Ratings (Frn)

SELECT

PG-13:

SEL Select

Move

NC-17:

SEL Return

Move

Use CURSOR ̆ or ̄ to select the MOVIE RATING category that you want to block.

Press SELECT to block the MOVIE RATING that you have selected. Once rating is selected, for example PG-13, all

movies rated PG-13 and higher (R, NC-17, and X) will be blocked.

Press EXIT to quit the menu or select MOVIE RATINGS to return to the previous menu.

Motion Picture Ratings Table

Contains no rating. Not Rated

(NR) and Not Applicable (NA) pro-

grams. Movie has not been rated or

ratings do not apply.

NOT RATED

General audiences. All ages admit-

ted.

Parental guidance suggested.

Some material may not be suitable

for children.

Parents strongly cautioned. Some

material may be inappropriate for

children under 13.

PG-13

Restricted. Under 17 requires

accompanying parent or adult

guardian.

No one 17 and under admitted.

NC-17

Adults only

NOTES: 1. A movie rating is dependent upon the movie that is viewed. If the movie does not carry a rating, the Projection

Monitor will not block it.

2. Blocking “NOT RATED” programs may block emergency programming, sports, news, public service

announcements, religious programs and weather.

LOCKS

Use TV RATINGS to prevent the viewing of any TV program that you feel may be inappropriate

due to its content.

TV Ratings

Locks

Change Access Code

Locks

TV Ratings

Status

Engage Lock

Sub Rating

Movie Ratings

TV Ratings

TV-Y:

Canadian Ratings (Eng)

Canadian Ratings (Frn)

TV-Y7:

TV-YG:

TV-PG:

TV-14:

TV-MA:

SELECT

SEL Select

Move

SEL Return

Move

Use CURSOR ̆ or ̄ to highlight the category that you want to block.

Press select to block the TV RATINGS that you have selected.

Press EXIT to quit the menu or select TV RATINGS to return to the previous menu.

TV Parental Guide Ratings Table

NOTE:

All children. The themes and elements in this

If you Block TV-14D, you will still permit

TV MA programs; If you block TV-14V,

you will automatically block TV-MAV

programs, but you will still permit TV-

MALS programs. This means that the

Projection Monitor will block violence in

TV-14 and higher (TV-MA), but not lan-

guage and sex.

TV program ratings are dependent on

the broadcaster. If the program is not

rated, the Projection Monitor will not

block it.

program are specifically designed for a very

young audience, including children from ages

2-6.

TV-Y

Directed to older children. Themes and ele-

ments in this program may include mild physi-

cal or comedic violence, or may frighten chil-

dren under the age of 7.

TV-Y7

TV-G

General audience. It contains little or no vio-

lence, no strong language, and little or no sex-

ual dialogue or situations.

Parental guidance suggested. The program

may contain infrequent coarse language, limit-

ed violence, some suggestive sexual dialogue

and situations.

TV-PG

Parents strongly cautioned. This program

may contain sophisticated themes, intense

sexual situation, more intense violence and

intensely suggestive dialogue.

TV-14

Mature audiences only. This program may

contain mature themes, indecent language,

graphic violence, and explicit sexual content.

TV-MA

Fantasy Violence

Violence

Sexual Situation

Adult Language

Sexually Suggestive Dialogue.

LOCKS

Use CANADIAN RATINGS (ENG) to block any type of movie and television program in Canada

that you feel might be inappropriate in its content.

Canadian Ratings

(Eng)

Locks

Change Access Code

Locks

Canadian Ratings (Eng)

Status

Engage Lock

Movie Ratings

TV Ratings

C8+:

Canadian Ratings (Eng)

SELECT

Canadian Ratings (Frn)

PG:

SEL Select

Move

14+:

18+:

SEL Return

Move

Use CURSOR ̆ or ̄ to select the CANADIAN RATINGS (Eng) category that you want to block.

Press SELECT to set the CANADIAN RATINGS (Eng) that you have selected. Once rating is selected, for example C8+,

all movies and television programs rated C8+ and higher (G, PG, 14+ and 18+) will be blocked automatically.

Press EXIT to quit menu.

Canadian Ratings English Table

Programming intended for children under age 8 - Violence Guidelines; Careful

attention is paid to themes, which could threaten children’s sense of security and well-

being. There will be no realistic scenes of violence. Depictions of aggressive behav-

iour will be infrequent and limited to portrayals that are clearly imaginary, comedic or

unrealistic in nature. Other Content Guidelines: There will be no offensive language,

nudity or sexual content.

Programming generally considered acceptable for children 8 years and over to

watch on their own - Violence Guidelines: Violence will not be portrayed as the pre-

ferred, acceptable, or only way to resolve conflict; or encourage children to imitate dan-

gerous acts which they may see on television. Any realistic depictions of violence will

be infrequent, discreet, of low intensity and will show the consequences of the acts.

Other Content Guidelines: There will be no profanity, nudity or sexual content.

C8+

General Audience - Violence Guidelines: Will contain very little violence, either physi-

cal or verbal or emotional. Will be sensitive to themes which could frighten a younger

child, will not depict realistic scenes of violence which minimize or gloss over the

effects of violent acts. Other Content Guidelines: There may be some inoffensive

slang, no profanity and no nudity.

Parental Guidance - Programming intended for a general audience but which may not

be suitable for younger children. Parents may consider some content inappropriate for

unsupervised viewing by children ages 8-13. Violence Guidelines: Depictions of con-

flict and/or aggression will be limited and moderate; may include physical, fantasy, or

supernatural violence. Other Content Guidelines: May contain infrequent mild profani-

ty, or mildly suggestive language. Could also contain brief scenes of nudity.

Programming contains themes or content which may not be suitable for viewers

under the age of 14 - Parents are strongly cautioned to exercise discretion in permit-

ting viewing by pre-teens and early teens. Violence Guidelines: May contain intense

14+

scenes of violence. Could deal with mature themes and societal issues in a realistic

fashion. Other Content Guidelines: May contain scenes of nudity and/or sexual activity.

There could be frequent use of profanity.

Adult - Violence Guidelines: May contain violence integral to the development of the

plot, character or theme, intended for adult audiences. Other Content Guidelines: May

contain graphic language and explicit portrayals of nudity and/or sex.

18+

LOCKS

Use CANADIAN RATINGS (FRN) to block Canadian French programs according to various pro-

gram ratings that you feel might be inappropriate in its content.

Canadian Ratings

(Frn)

Locks

Change Access Code

Locks

Canadian Ratings (Frn)

Status

Engage Lock

Movie Ratings

8 ans+:

13 ans+:

16 ans+:

18 ans+:

TV Ratings

Canadian Ratings (Eng)

Canadian Ratings (Frn)

SELECT

SEL Select

Move

SEL Return

Move

Use CURSOR ̆ or ̄ to highlight the category that you want to block.

Press SELECT to set the CANADIAN RATINGS (Frn) that you have selected.

Once rating is selected, for example 8 ans+, all movies and television programs rated 8 ans+ and higher will be

automatically blocked.

Press EXIT to quit menu or select CURSOR ̇ to return to the previous menu.

Canadian Ratings French Table

General - Programming intended for audiences

of all ages. Contains no violence, or the vio-

lence content is minimal or is depicted appropri-

ately with humor or caricature or in an unrealis-

tic manner.

8 + General - Not recommended for young

children - Programming intended for a broad

audience but contains light or occasional

violence that could disturb young children.

Viewing with an adult is therefore recommended

8 ans +

for young children (under the age of 8) who can-

not differentiate between real and imaginary

portrayals.

Programming may not be suitable for chil-

dren under the age of 13 - Contains either a

few violent scenes or one or more sufficiently

violent scenes to affect them. Viewing with an

adult is therefore strongly recommended for

children under 13.

13 ans +

Programming is not suitable for children

under the age of 16 - Contains frequent scenes

of violence or intense violence.

16 ans +

18 ans +

Programming restricted to adults - Contains

constant violence or scenes of extreme violence.

SETUP

Select SETUP when setting your Projection Monitor up for the first time. Use the CURSOR ̆ or ̄ on the remote

to highlight the function desired.

Setup

Video

Audio

Aspect

Locks

Setup

Move

Setup

Magic Focus Tune Up

Menu Preference

Set The Clock

Set The Inputs

Set The Color System

Set Virtual HD

SELECT

SEL

Sel

Set Black Side Panel

Set Closed Captions

About Your TV

SEL Return

Move

Use CURSOR ̆ or ̄ to select the sub-menu of your choice.

SETUP

Magic Focus

Tune Up

Auto Digital Convergence Adjustment

Please turn ON your Projection Monitor for at least 20 minutes before using this feature.

The Magic Focus button on control panel will not work when adjustment mode is set to Manual (see page 47).

Your ASPECT Projection Monitor has three color projection tubes: one for red, one for green, one for blue. When mixed together in the

proper proportion, the output of these three color tubes can produce any color. To produce these colors, however, the beams must be

precisely aligned over each other so that the colors can be mixed. The process of aligning these picture beams is called “convergence”.

Over a period of time, the picture tubes can drift out of alignment due to normal bumps and vibrations or moving the Projection Monitor.

If you move your Projection Monitor, or if, after a time, you notice color rings or halos around objects in the picture, you may want to

converge (align) the colors.

Properly converged, the lines appear white, which is actually a combination of the outputs of the three color tubes. The output of the

green tube is stationary. The outputs of the red and blue tubes can be adjusted. When properly aligned, the outputs of all three tubes

should be directly over each other to produce the white lines.

To simplify convergence, ASPECT Projection Monitor incorporates a function called MAGIC FOCUS located on the front control panel,

which allows the Projection Monitor to self-adjust. Press this MAGIC FOCUS button and the convergence self adjustment will start and

this process will take approximately 20 seconds. If this button is pressed during this process, no change in picture quality will occur.

After this 20 second self-adjust period, picture quality will be optimum (do not move the Projection Monitor during self-adjust).

You may also select MAGIC FOCUS TUNE UP from the Setup Menu.

MAGIC FOCUS

NOTES: Only a momentary press of the MAGIC FOCUS button is necessary to start AUTO DIGITAL CONVERGENCE. At any

time during this convergence correction process, you may press the MAGIC FOCUS button to exit the MAGIC FOCUS

mode. However, the convergence correction process needs to be completed to SAVE the new corrected convergence

data.

Video

Audio

Aspect

Locks

Setup

Move

Setup

Magic Focus Tune Up

Menu Preference

Set The Clock

Set The Inputs

Set The Color System

Set Virtual HD

SELECT

SEL

Sel

Set Black Side Panel

Set Closed Captions

About Your TV

SEL Select

Move

SELECT

Setup

Magic Focus Tune Up

Aligns the Red, Green, and Blue

colors to correct for Magnetic

Influences.

Adjustment Mode

Auto

MAGIC FOCUS

SELECT

Manual

If you want to adjust now

Start

SEL Return

Move

SETUP

Manual Convergence Adjustment Mode

NOTES: 1. Please turn ON your Projection Monitor for at least 20 minutes before using this feature.

2. Auto Adjustment Mode is recommended. If convergence is still not acceptable, use the Manual Adjustment Mode.

3. If Auto Adjust mode is selected or the Magic Focus button is pressed, all manual adjust mode settings will be erased.

Using the Remote Control, select SETUP-MAGIC FOCUS TUNE UP-MANUAL ADJUSTMENT MODE-START to access convergence

crosshatch pattern. The adjustment point is indicated by the Adjustment Point Cursor.

To Move Adjustment Point

To move the adjustment point cursor using the CURSOR buttons, the Adjustment Cursor must be WHITE. Another way to move the

Adjustment Point Cursor is to press the following buttons: [2] up, [4] left, [5] down, [6] right. If you use the number buttons while the

adjustment point is WHITE, it will change to RED.

To Change the Color of Adjustment Point

Press the SELECT button repeatedly (WHITE-RED-BLUE-WHITE...). Green color is fixed and cannot be adjusted.

To Adjust the Convergence

Move the Adjustment Cursor to the point to be adjusted. Use the CURSOR to match the RED and BLUE colors to GREEN (reference

color). Properly aligned, all three colors should appear white.

Video

Audio

Aspect

Locks

Setup

Move

Setup

Magic Focus Tune Up

Menu Preference

Set The Clock

Set The Inputs

Set The Color System

Set Virtual HD

SELECT

SEL

Sel

Set Black Side Panel

Set Closed Captions

About Your TV

SEL Select

Move

SELECT

Adjustment Point

Cursor

Setup

Magic Focus Tune Up

Aligns the Red, Green, and Blue

colors to correct for Magnetic

Influences.

Adjustment Mode

Auto

SELECT

Manual

If you want to adjust now

Start

SEL Return

Move

If convergence is acceptable after Manual Convergence adjustment, press EXIT button to access menu mode.

117 Manual Adjust

Please Enter Number.

0.Cancel and go to Normal Mode.

1.Done and go to Normal Mode.

EXIT

2.Back to Adjust Mode

3.Factory Reset and back to

Adjust Mode.

0-3.Select

Press the [0] button on the remote control to CANCEL adjusted data and return to main picture.

Press the [1] button on the remote control to SAVE adjusted data and return to main picture.

Press the [2] button on the remote control to return to the manual convergence adjustment mode (crosshatch pattern).

Press the [3] button on the remote control to recall the factory pre-set convergence data.

SETUP

Menu Preference

This feature will allow you to select any one of three different languages for all on-screen displays.

Setup

Magic Focus Tune Up

Menu Preference

Set The Clock

Menu Preferences

Set The Language

English

Francais

Español

Set The Inputs

Set The Menu Background

Shaded

Solid

Set The Color System

Set Virtual HD

SELECT

SEL Return

Move

Set Black Side Panel

Set Closed Caption

About Your TV

SEL Select

Move

Setup

Menu Preferences

Set The Language

English

Francais

Español

Set The Menu Background

Shaded

Solid

SEL Select

Move

Use CURSOR ̇ or ̈ to highlight the language of your choice.

Press SELECT to select the highlighted language.

Press EXIT to quit menu or select MENU PREFERENCE to return to previous menu.

SETUP

This function allows you to choose from two menu backgrounds.

Menu Background

Setup

Menu Preferences

Set The Language

English

Francais

Español

Set The Menu Background

Shaded Solid

^SELSelect

Move

Use CURSOR ̇ or ̈ to highlight SET THE MENU BACKGROUND (shaded or solid), and press the SELECT button to select setting.

Press EXIT to quit menu or CURSOR ̇ to return to previous menu.

Select SOLID for a black background (no picture can be seen behind menu screen), or select SHADED for a light background.

Set The Clock

The clock must be adjusted before you can use the “Set Event Timer” features.

Setup

Magic Focus Tune Up

Menu Preference

Set The Clock

Set The Inputs

Set The Color System

Set Virtual HD

SELECT

Time : 03:57 PM Apr 29, 2005

Set Black Side Panel

Set Closed Caption

About Your TV

SEL Return

Move

SEL Select

Move

Setup

Set The Clock

Time : 03:57 PM Apr 29, 2005

SEL Return

Move

Set

Use CURSOR ̆ or ̄ to set the time and date.

Press CURSOR ̇ or ̈ to change position.

Press EXIT to quit menu or select SET THE CLOCK to return to previous menu.

SETUP

Use this feature to give a name to any of the five video inputs.

Set The Inputs

Setup

Set The Inputs

Video1 Rename List

Magic Focus Tune Up

Menu Preference

Set The Clock

Set The Inputs

Video2

Video3

Video4

Video5

AVR

CAM

CBL

CBL2

DVD

DVD2

PVR2

SAT

VCR

VCR2

Set The Color System

STB

SELECT

Set Virtual HD

PVR

STB2

Reset

Set Black Side Panel

Set Closed Caption

About Your TV

SEL Select

Move

SEL Return

Move

Press CURSOR ̆, ̄, ̇, ̈ to highlight the name of the video inputs.

Press the SELECT button to select desired input name.

Select RESET to set video names to original factory preset condition.

Use this function to automatically turn the Projection Monitor on and tune to Video2 when it detects a video

signal to input 2.

Video 2 Auto Link

Setup

DVD

Set The Inputs

Video1 Rename List

Set The Inputs

Video1

Video2

Video3

Video4

Video5

Rename List

Video2

Video3

Video4

Video5

AVR

CAM

CBL

CBL2

DVD

DVD2

PVR2

SAT

VCR

AVR

CAM

DVD

DVD2

PVR2

SAT

VCR

VCR2

STB

CBL

STB

PVR

STB2

Reset

CBL2

PVR

STB2

Reset

(2 times)

Auto Link

Auto

Remote Off

SEL Return

Move

Use CURSOR ̇, ̈, ̆ and ̄ then press the SELECT button to change AUTO LINK setting.

When AUTO is selected, the Projection Monitor will turn on and tune to Video2 automatically, when the Video2 input device is turned

on. This is convenient when you want to watch a movie with your VCR, laserdisc player, or DVD player.

When REMOTE is selected, the Projection Monitor will turn on and switch to Video2 automatically when the Video2 input device is

turned on and the VCR, laserdisc, or DVD play button on your remote control is pressed.

This is convenient when you want to record a movie with your VCR and watch it later.

Select Off to disable this function.

Press EXIT to quit menu.

NOTES: 1. Once the Projection Monitor has been turned on using the AUTO LINK feature, it must be reset before AUTO LINK is

used again. To do this, turn your VCR, laserdisc, or DVD player OFF. This feature is now reset and will turn on your

Projection Monitor as described above.

2. When using REMOTE mode, any remote control button will substitute for your video input device play button.

However, intended operation is for use with your VCR, laserdisc, or DVD play button.

3. If no remote control button is pressed after the Projection Monitor is turned on by AUTO LINK, the Projection Monitor

will automatically turn off after three hours.

SETUP

This function allows you to automatically change tint and color coordinates for DTV programs.

HDTV - High Definition Television - Use for High Vision Signal Y-P_BP_Rfrom HDTV Set-Top Box.

Set The Color

System

SDTV/DVD - Standard Definition Television or DVD (Digital Versatile Disc Player) Y-C_BC_R.

NOTES: 1. If Color System is set improperly (does not match actual input signal), the color and tint of the main picture will be

abnormal.

2. You must be tuned to VIDEO: 1 or 2 inputs and have a component hooked up to the Y-P P input jacks to access

B R

this color system.

3. All component color type settings will affect only color component input you are currently viewing. If you are using

both sets of component input jacks, be sure to set the color system feature for both inputs.

Set Virtual HD

Use this feature to select between 1080i and 540p.

The BLACK SIDE PANEL function turns the gray side bars on/off when watching 4:3 signals in

Standard mode. The top/bottom gray bar will appear in SPLIT MODE PIP and SPLIT FREEZE.

Set Black Side

Panel

NOTE:

To maximize operating life of the Projection Monitor’s picture tubes when watching 4:3 signal, Black Side Panel is can-

celled at Power OFF. It is recommended to watch 4:3 signal with gray side bar.

SETUP

Closed Captions are the dialogue, narration, and/or sound effects of a television program or home video

which are displayed on the Projection Monitor screen. Your local TV program guide denotes these programs

Set Closed

Caption

Setup

Set Closed Caption

Caption Display

Off On

Magic Focus Tune Up

Menu Preference

Set The Clock

Auto

Text

Set The Inputs

Analog Captions

Mode:

Channel:

Captions

Set The Color System

Set Virtual HD

SELECT

Set Black Side Panel

Set Closed Caption

About Your TV

SEL Return

Move

SEL Select

Move

Caption Display:On/Off will turn the

display on or off.

display on when Mute/Soft Mute is on.

Auto will turn the

Caption Mode: Captions is for the program you are viewing.

Text is for additional information such as news reports or a TV program guide. This information covers the entire

screen and viewing the TV program is not possible. Text may not be available with every

program.

CHANNEL:

1 is used for the primary language (usually English).

2 is sometimes used for a second language (may vary by region).

3 is sometimes used for a third language (may vary by region).

4 is sometimes used for a fourth language (may vary by region).

Use CURSOR ̆, ̄ to highlight the function to change then press the SELECT button to change the function.

Press EXIT to quit menu or CURSOR ̇ to return to previous menu.

NOTE:

1. CAPTION DISPLAY will not work when viewing a 480p, 720p, or 1080i input via the COMPONENT: Y-P P inputs.

B R

2. When PIP Surf is on, Closed Caption will not work.

The Projection Monitor model name and set dimensions will be displayed on the screen. The set dimensions

of the Projection Monitor model is listed on page 56.

About Your TV

Setup

Magic Focus Tune Up

Setup

About Your TV

Menu Preference

Set The Clock

Model:

Dimensions (Inches) (mm)

Set The Inputs

Set The Color System

Set Virtual HD

Height:

Width:

Depth:

- / -

SELECT

Set Black Side Panel

Set Closed Caption

About Your TV

Caution

SEL Select

Move

SEL Return

Move

SELECT

Setup

About Your TV

Caution:

Continuous on-screen

displays such as Video games, stock

market quotations, and other

fixed (non-moving) patterns can

cause permanent damage.

Such “SCREEN BURNS” are not covered

by your Hitachi Factory Warranty.

SEL Return

Move

CARE OF YOUR ASPECT PROJECTION MONITOR

AND YOUR REMOTE CONTROL

Dust the screen and cabinet with a soft cloth.

Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if

the screen is extremely dirty.

Place your Projection Monitor away from extreme heat, humidity, and extremely dusty places.

Remove the plug from the wall outlet if your Projection Monitor will not be used for a long period of time, for

instances, when you go on vacation.

DO NOT

Do not clean your screen or cabinet with strong cleaners, polishes or a chemically treated cloth.

Do not place rubber or vinyl products or cellophane tape on your Projection Monitor.

Do not touch the screen too often.

Do not subject the remote control to shocks such as dropping it on the floor, etc. Physical damage to the precision

parts may result.

Avoid placing the remote control in a high humidity place or getting it wet. Do not leave it on or near a heater.

Excessive heat or moisture may cause the unit to cease operation.

When the batteries run down, remote control operation will become erratic or possibly stop altogether. Replace the

old batteries with two new “AA” size batteries. Do not use an old battery with a new battery.

Exposure of the viewing screen to prolonged direct sunlight or heat may cause the screen to permanently warp,

resulting in a distorted picture.

Reception Problems

• IGNITION NOISE:

Black spots or horizontal streaks may appear, picture may flutter or drift.

Usually caused by interference from automobile ignition systems, neon

lamps, electrical drills, and other electrical appliances.

• GHOSTS:

Ghosts are caused by the television signal following two paths. One is the

direct path and the other is reflected from tall buildings, hills or some other

objects. Changing the direction or position of the antenna may improve

reception. Ghosting may also be caused by defects in the antenna system

such as unshielded leads or connecting several sets to the same antenna

without using multiple antenna couplers.

• SNOW:

If your receiver is located in the fringe area of a television station where

the signal is weak, your picture may be marred by the appearance of small

dots. When the signal is extremely weak, it may be necessary to install a

special antenna to improve the picture.

• RADIO FREQUENCY INTERFERENCE:

The interference produces moving ripples or diagonal streaks, and in

some cases, causes loss of contrast in the picture.

NOTE:

The Projection Monitor can generate sound distortion in external devices such as a radio. Please separate radio equip-

ment from the Projection Monitor set to a considerable distance.

USEFUL INFO

SYMPTOMS

No Picture, no sound

Sound OK, picture poor

Picture OK, sound poor

Picture blurred

Lines or streaks in picture

Picture rolls vertically

No color

Poor color

ASPECT Projection Monitor incorporates advanced power surge protection technology designed to protect against

component or circuit damage due to external or internal voltage power surges.

IF YOUR PROJECTION MONITOR SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS PRO-

CEDURE:

1. Press the power switch (ON/OFF switch) once.

2. If there is still no power, wait 30 seconds and press the power switch again.

3. If there is still no power, unplug the power cord from the wall. Wait 30 seconds and plug the power cord back in.

Press the power switch again.

This protective technology should provide for years of lasting entertainment from your ASPECT Projection Monitor.

USEFUL INFO

Features:

•

Superfine Picture Quality

1280 Line Horizontal Resolution

•

Remote (Controls many VCRs, DVD players, cable boxes, and satellite boxes.)

New Easy-to-Use (3-Language) On-Screen Menu

Full Set of Input Jacks, including S-VIDEO

COMPONENT VIDEO: Y-P_B/P_R

Velocity Modulation

Six Aspect Modes

Closed Caption Decoder

Picture in Picture

Magic Focus (Auto Digital Convergence and Manual Adjustment)

Video Input Sensor

3 Dimensional Y/C Comb Filter

Compatible with 1080i, 720p, 480p and 480i input signals.

DVI-HDTV (High bandwidth Digital Content Protection V1.0 compatible).

High Bandwidth Digital Content Protection V1.0 Compatible.

•

Technology.

*Licensed by BBE Sound, Inc. under USP5510752 and 5736897. BBE and BBE symbol are registered

trademarks of BBE Sound, Inc. Manufactured under license from BBE Sound, Inc.

•

Technology.

*SRS and the

SRS Labs, Inc.

symbol are trademarks of SRS Labs, Inc. SRS technology is incorporated under license from

Inputs:

Dimensions:

•

Power Input . . . . . . . . . . . . . .AC 120V, 60Hz

51M200

51M200A 65M200

•

Stand-by Power . . . . . . . . . . . . . . . . . .1.3W

Power Consumption

- Refer to rear panel at the back of the Projection

Monitor

Video . . . . . . . . . . . . . . . . .1.0Vp-p, 75 Ohm

•

Height (in.)

(mm)

50 1/4

1,275.0

59 7/8

1,520.7

Width (in.)

(mm)

48 3/4

1,239.0

1,549.0

•

Depth (in.)

(mm)

25 1/16

636.0

28 3/16

716

S-Video

Luminance (Y) . . . . . . . . . .1.0Vp-p, 75 Ohm

Chrominance (C) . . . . . . .0.286Vp-p, 75 Ohm

•

Weight (lbs.)

(kg.)

245

111.0

324

147.0

•

Component Video

Luminance (Y) . . . . . . . . . . . . . . .1.0Vp-p, 75 Ohm

Chrominance (P /P ) . . . . . . . . .0.7Vp-p, 75 Ohm

Audio input Impedence . . . . . . . . . .47k Ohm

•

Average input level . . . . . . . . . . . . . . . . .470mVrms

DVI-HDTV . . . . . . . . . . . . . . . . . . . . . . . .DVI 25 pin

Outputs:

•

Video . . . . . . . . . . . . . . . . . . . . . . .1.0Vp-p. 75 Ohm

Audio (Fixed) . . . . . . . . . . . . . .470mVrms, 1k Ohm

NOTE:

Due to improvements, specifications in this oper-

ating guide are subject to change without notice.

USEFUL INFO

To locate an authorized

ASPECT service facility

in the continental U.S.A.

and Canada,

DIAL TOLL FREE

7 days a week, 24 hours a day

ASPECT Brand Electronics

ASPECT has made every effort to assure you hours of trouble free operation from your unit. However, should you require serv-

ice, a network of ASPECT Authorized Service Facilities has been established in all 50 states and Puerto Rico. Each facility will

provide you with convenient and expedient assistance. Our service hotline operator will direct you to the ASPECT Authorized

Service Facility nearest you. Just present proof of purchase and/or delivery receipts to the ASPECT Authorized Service Facility,

and service will be rendered in accordance with the terms of the limited warranty as stated on your warranty card or operating

guide.

Should you have any questions regarding warranty, service, operation, or technical assistance, please contact:

ASPECT Brand Electronics

2420 Fenton Street

Chula Vista, CA 91914

INDEX

Accessories, 4

Language

Remote Control

Aspect Ratio, 23

Audio (Sound Enhancement)

SRS, 38

Menu Language, 48

Locks

Change Access Code, 40

Functions, 20 - 31

Programming Codes, 28 - 30

Installing Batteries, 4

BBE, 38

Audio Settings, 37 - 38

Auto Color, 36

Input Lock, 40

Front Panel Lock, 40

TV Time Lock, 40

Movie Ratings, 41

TV Ratings, 42

Sharpness, 34

Balance, 37

Bass, 37

TV Ratings

Sound Enhancement, 38

Speakers, 37

(Canadian - English), 43

TV Ratings

(Canadian - French), 44

Connecting External Speakers, 5, 13

Black Enhancement, 34

Black Side Panel, 51

Brightness, 34

Loudness, 37

Magic Focus

Time, 49

Tint, 34

Treble, 37

Clock

Time, 49

Closed Captions

Captions, 52

Color Management, 35

Color Temperature, 34

Color, 34

Auto Convergence, 7, 46

Manual Convergence, 47

Menu Preference

Language, 48

Background, 49

Monitor Out, 9

Vertical Position, 39

Video Settings, 33 - 36

Contrast, 34

Convergence (see Magic Focus)

Picture Mode, 33

Picture-in-Picture (PIP), 25 - 27

Picture-outside-Picture (POP), 25

Input Setup, 50

NOTES

QR64461

Advent TOYBTSW3 User Manual
BlueTrek EN300 328 02 User Manual
Bosch Appliances Boiler 24i junior User Manual
Burnham LEDV 1 User Manual
GN Netcom Jabra BT250v User Manual
HP (Hewlett Packard) Hewlett Packard Car Video System S1931A User Manual
Hypertec 3102 User Manual
Hypertec PerfectSkin N12308NHY User Manual
JVC Everio GZ HM50U User Manual
JVC GR SXM250 User Manual